Professional Documents
Culture Documents
JSA Concrete Works
JSA Concrete Works
Concrete Works WORK ACTIVITY: ___________________________________ Each piece of equipment and crew are associated with known specific hazards that cause accidents to reoccur on one project after another. xxxx Sundararajan SITE SUPERVISOR:___________________ LOCATION ;____________________ PERMIT #:____________
Probability factors. 5 8 6 4 2 1
No 1. Activity ( Job Steps ) Work permit from Client to be obtained.
DECC
Severity Factors 8: Fatality, Permanent Disability 6: Serious Injury (LD>30 days) 4: Major Injury (30>LD>4 days) 2: Minor Injury (4>LD>1 day)
Probability Factors 5 : Extremely High 4 : Highly Probable 3 : Probable 2 : Rare 1 : Very Rare
Abbreviation E.P :Evaluation Points S : Severity Factor P : Probability Factor T : Total Points LD : Lost Workdays
Potential Hazard Unauthorized commencement of works may result in exposing workers and or potential to harm or danger
Who/ What Might Be Harmed Injury to IMCO Personnel and or client property.
Control/ Recovery Measures Authorized PTW holder shall ensure obtaining and maintaining valid work permit. The worksite supervisor responsible for this activity has to check the PPE of his staff to ensure that all required items are available and properly used. Inform all workers regarding permit condition before work starts. Worksite supervisor shall conduct toolbox talks about nature of works and associated potential hazards and their essential precautionary measure.
No
Potential Hazard Delay to schedule Physical injury from heavy equipment, heavy lifting, pinch point, slip, trips and fall hazards
Control/ Recovery Measures Follow mobilization schedule and arrange the required documents to avoid any cause of delay. Before transporting the loads to the site, rest assure that the materials are secured and tight with nylon rope for the safe transporting. Ensure that a driver is having knowledge to the hazard while transporting the materials. The driver shall not have driving attitude while using the road. Driver is driving only in the minimum speed limit. Minimize work personnel in the vicinity of equipment. Provide ergonomic training, institute good housekeeping procedure. Keep feet and hands clear of moving/suspended materials and equipment. Keep a tidy site. Ensure that the pre task briefing is given out in a language understood by the work force, have it translated. Ask question regarding the briefing to get feedback from the staff, this ensures full comprehension. Issue required appropriate PPE and
4 x 4 = 16
2x1=2
The work force does not understand the pre task briefing therefore does not understand the potential dangers and control measures to be implemented. Some of the workers could be
IMCO Personnel
2x4=8
2x1=2
Page 2 of 8
No
Control/ Recovery Measures replace PPE that has signs of defect. PPE must include both hearing protection as well as dust inhalation protection. Ensure that adequate shaded areas are provided. Provide proper ventilation and drink plenty of water even if you are not thirst. Wear loose fitting full length clothing that can breathe. Ensure that all markers and signage are of a suitable height to be clearly seen and sufficient lighting is placed to identify the area at night. Ensure that all equipment is having valid QP certificates to work in the vicinity. Make sure all operators know the safe limitations of their equipment. Assigned a competent banksman when equipment is moving at the working area. Ensure strict control measure to separate mechanical plant and enforce swing radius area as no go area for any person or vehicle in order to avoid collisions. Set control measure in place that all fuel transfers take place under strict guidelines. Fuel is only transferred by purpose built fuel delivery tanker.
Responsible/ Action By
IMCO personnel
4 x 3 = 12
2x1=2
Unloading the ready mix concrete from truck and from concrete pumps
Markers are not clearly visible creating a risk of others coming into the area. Machine works too close to persons within the same working area.
IMCO personnel
2x1=2
Site supervisor, workers and site safety officer Site supervisor, workers and site safety officer
IMCO personnel
4 x 3 = 12
2x1=2
Machine strikes another vehicle or person in the vicinity. Machine creates an environmental hazard by fuel leakage during fuel transfer or by
IMCO personnel
4 x 3 = 12
2x1=2
IMCO personnel
4 x 3 = 12
2x1=2
Page 3 of 8
No
Control/ Recovery Measures Ensure all machines and equipments are in good condition. Regular preventive and corrective maintenance of equipment must be observed. Drip trays are used to prevent any spillage. Make sure all vehicles are routinely inspected and maintained to reduce the risk of mechanical failure. In the event that there is ground contamination ensure all contaminated ground is collected and placed into plastic bags, removed to a waste storage container until removed from site to a hazardous waste disposal site. Deploy equipment delivering materials in such manner that no congestion inside shall happen and no parking anytime in the work area. Use only designated roads for delivery of concrete. Ensure to wear suitable respiratory protective equipment such as a P, N or R 95 respirator when fumes from dust cant be avoided. Remove person to fresh air. If discomfort persists seek medical advice. Ensure to wear loose clothing in
Responsible/ Action By
Traffic congestion
IMCO personnel
4 x 3 = 12
2x1=2
IMCO personnel
4 x 4 = 16
2x1=2
Page 4 of 8
No
Potential Hazard
Control/ Recovery Measures good condition with collars closed and cuffs buttoned at the wrist. In case of chemical contact, Remove chemical from skin with waterless hand cleaner Housekeeping regimes to help keep site clear Ensure sufficient space around work areas Ensure there is good access for concrete personnel and equipment Keep other people not directly involved with concrete pouring clear from area Ensure that penetrations are secured, identified and covered
Responsible/ Action By
Poor access to working area causing of slips, trips, falls and or other injuries Penetration not cover that cause falling onto sharp object Violent ejection of concrete from hose at first moment of delivery IMCO personnel or Client inspector IMCO personnel 4 x 4 = 16
4 x 3 = 12
2x1=2
2x1=2
4 x 4 = 16
IMCO personnel
4 x 3 = 12
Give warning prior to starting or recommencing the pour Check hoses for air sources, e.g.: blockage change in supply poor mix or delays in the pour Ensure delivery hose is not damaged prior to pour Control T-bar at end of hose Be aware of potential for blow back in the line Ensure appropriate edge protection Ensure connecting pipes are adequately secured Ensure brackets are positioned close
2x1=2
Site supervisor, workers and site safety officer Site supervisor, workers and site safety officer
2x1=2
Page 5 of 8
No
Potential Hazard
Control/ Recovery Measures together to minimize excessive movement Ensure that pipe's operating pressure is appropriate for diameter of pipe Check pipe to ensure it is of correct thickness for operating pressure Do not use damaged pipes Provide support where a change in direction or reducer occurs Do not walk backwards during delivery Ensure T-bar does not slip off end of hose Avoid getting feet caught in reinforcement Put caps on ends of exposed reinforcement bars Turn tie wires into reinforcement cages Use quieter or muffled equipment where practicable Provide adequate hearing protection suitable for the level of noise exposure Do not refuel when machine is in operation Ensure there is adequate ventilation when refueling and using the vibrator Wear appropriate PPE Provide rest times or alternate work
Responsible/ Action By
Walking on the concrete foundation during the pour that causing slipping on wet ply or reinforcement Sharp edges cause of cuts from reinforcement bar ends or tie wire Noise from operating machinery causing to hearing loose IMCO personnel 4 x 3 = 12 IMCO personnel 4 x 3 = 12 IMCO personnel
2x1=2
2x1=2
Site supervisor, workers and site safety officer Site supervisor, workers and site safety officer
2x1=2
IMCO personnel Fumes from fuel used and or damage to for vibrator possible to property explosion and/or fire, burns, rashes or allergies Sprain or strain cause of IMCO personnel
4 x 4 = 16
2x1=2
4 x 3 = 12
2x1=2
Site supervisor,
Page 6 of 8
No
Control/ Recovery Measures rotation Avoid long periods of twisting, repetitive movements Provide job rotation where there are enough trained employees Ensure the concrete is not too dry when screeding and shoveling Become acclimated to the heat gradually before working in hot temperatures for a long time; Ensure 100% availability of cold water and always drink plenty of cool water; Wear hats and sunglasses to help stay cool; Take frequent breaks in a cool place, if possible; Wear loose clothing that allows the skin to breathe, such as cotton; Protect your skin from the sun. Keep as much of it covered with clothing as possible. Wearing long-sleeved shirts will help; Field supervision/ HSE personnel shall closely monitor the condition of workers, intervene as the need arises. Switch equipment / vehicles headlights and flashers on while in motion Maintain all required lights, reflectors and accessories on
IMCO personnel can cause heat cramps, heat exhaustion or heat stroke
4 x 4 = 16
2x1=1
4 x 3 = 12
2x1=1
Page 7 of 8
No
Potential Hazard
Control/ Recovery Measures equipment; Keep your equipment a safe distance from the edge of embankment; Speed must be effectively reduced or shall completely STOP when the situation calls for it. Personnel must keep away from vehicle path as much as possible. Ensure other workers are out of the way before starting the machine; Keep reverse alarms operable and free of anything that will muffle the sound;
Responsible/ Action By
IMCO personnel
4 x 3 = 12
2x1=1
Site supervisor and safety Officer Site supervisor and safety Officer
IMCO personnel
4 x 3 = 12
2x1=1
Page 8 of 8