Professional Documents
Culture Documents
Digital Microwave Communication Principles
Digital Microwave Communication Principles
www.huawei.com
Foreword
z
This course is developed to meet the requirement of Huawei Optical Network RTN microwave products.
This course informs engineers of the basics on digital microwave communications, which will pave the way for learning the RTN series microwave products later.
Page 2
Learning Guide
z
Microwave communication is developed on the basis of the electromagnetic field theory. Therefore, before learning this course, you are supposed to have mastered the following knowledge:
Page 3
Objectives
z
Concept and characteristics of digital microwave communications Functions and principles of each component of digital microwave equipment
Anti-fading technologies Procedure and key points in designing microwave transmission link
Page 4
Contents
1. Digital Microwave Communication Overview 2. Digital Microwave Communication Equipment 3. Digital Microwave Networking and Application 4. Microwave Propagation and Anti-fading Technologies 5. Designing Microwave Transmission Links
Page 5
Microwave TE
Microwave TE
MUX/DEMUX
Microwave communication
MUX/DEMUX
Satellite communication
Page 6
Page 7
Definition of Microwave
z
Microwave
Microwave is a kind of electromagnetic wave. In a broad sense, the microwave frequency range is from 300 MHz to 300 GHz. But In microwave communication, the frequency range is generally from 3 GHz to 30 GHz.
According to the characteristics of microwave propagation, microwave can be considered as plane wave.
The plane wave has no electric field and magnetic field longitudinal components along the propagation direction. The electric field and magnetic field components are vertical to the propagation direction. Therefore, it is called transverse electromagnetic wave and TEM wave for short.
Page 8
34/140M
2/4/6/8M
Small and medium capacity digital microwave communication system Analog microwave communication system
1980s 1970s 1950s Note: Small capacity: < 10M Medium capacity: 10M to 100M Large capacity: > 100M
Page 9
Digital microwave communication is a way of transmitting digital information in atmosphere through microwave or radio frequency (RF).
Microwave communication refers to the communication that use microwave as carrier . Digital microwave communication refers to the microwave communication that adopts the digital modulation.
The baseband signal is modulated to intermediate frequency (IF) first . Then the intermediate frequency is converted into the microwave frequency.
The baseband signal can also be modulated directly to microwave frequency, but only phase shift keying (PSK) modulation method is applicable.
The electromagnetic field theory is the basis on which the microwave communication theory is developed.
Page 10
Regional network
3.3 GHz 2/8/34 Mbit/s 34/140/155 Mbit/s 2/8/34/140/155 Mbit/s GHz 1 2 3 4 5 8 10 20 30 40 50
11 GHz
Page 11
In each frequency band, subband frequency ranges, transmitting/receiving spacing (T/R spacing), and channel spacing are defined.
Frequency range
Low frequency band T/R spacing Protection spacing T/R spacing f0 (center frequency) High frequency band
Channel spacing f1 f2 fn
Channel spacing f2 fn
Page 12
f1=7442
f2=7470
f5
f1=7596
f2
f5
F0 (MHz)
7575 7575
71107750 72507550
Page 13
Digital baseband signal is the unmodulated digital signal. The baseband signal cannot
be directly transmitted over microwave radio channels and must be converted into carrier signal for microwave transmission.
Channel bandwidth
Modulation
IF signal
Page 14
A*COS(Wc*t+)
Amplitude Frequency Phase
ASK: Amplitude Shift Keying. Use the digital baseband signal to change the carrier amplitude (A). Wc and remain unchanged. FSK: Frequency Shift Keying. Use the digital baseband signal to change the carrier frequency (Wc). A and remain unchanged. PSK: Phase Shift Keying. Use the digital baseband signal to change the carrier phase (). Wc and A remain unchanged. QAM: Quadrature Amplitude Modulation. ). Use the digital baseband signal to change the carrier phase () and amplitude (A). Wc remains unchanged.
Page 15
RFCOH
171.072 Mbit/s 15.552 Mbit/s RFCOH STM-1 155.52 Mbit/s SOH Payload
MLCM DMY XPIC ATPC WS RSC INI ID FA 11.84 Mbit/s 64 kbit/s 16 kbit/s 64 kbit/s 2.24 Mbit/s 864 kbit/s 144 kbit/s 32 kbit/s 288 kbit/s RFCOH: Radio Frame Complementary Overhead RSC: Radio Service Channel MLCM: Multi-Level Coding Modulation INI: N:1 switching command DMY: Dummy ID: Identifier XPIC: Cross-polarization Interference Cancellation FA: Frame Alignment ATPC: Automatic Transmit Power Control WS: Wayside Service
Page 16
RFCOH is multiplexed into the STM-1 data and a block multiframe is formed. Each multiframe has six rows and each row has 3564 bits. One multiframe is composed of two basic frames. Each basic frame has 1776 bits. The remaining 12 bits are used for frame alignment. Multiframe 3564 bits
Basic frame 1 1776 bits148 words
I I I I I C1 I I I I I I I I I I I I I I I I I C1 I I I I I I I I I I I I I I I I b C1 I I I I I I I I I I I I I I I I C2 C1
6 bits
FS 6 bits
FS 6 bits
I I I I I I
I I I I I I
12 bits (the 1st word) I: STM-1 information bit C1/C2: Two-level correction coding monitoring bits FS: Frame synchronization a/b: Other complementary overheads Copyright 2006 Huawei Technologies Co., Ltd. All rights reserved.
Page 17
Questions
z
What is microwave? What is digital microwave communication? What are the frequently used digital microwave frequency bands? What concepts are involved in microwave frequency setting? What are the frequently used modulation schemes? Which are the most frequently used modulation schemes?
Page 18
Contents
1. Digital Microwave Communication Overview 2. Digital Microwave Communication Equipment 3. Digital Microwave Networking and Application 4. Microwave Propagation and Anti-fading Technologies 5. Designing Microwave Transmission Links
Page 19
Capacity
Page 20
High cost, large transmission capacity, more stable performance, applicable to long haul and trunk transmission RF, IF, signal processing, and MUX/DEMUX units are all indoor. Only the antenna system is outdoor.
P M1 M2
MSTU: Main Signal Transmission Unit (transceiver, modem, SDH electrical interface, hitless switching) SCSU: Supervision, Control and Switching Unit
BBIU: Baseband Interface Unit (option) (STM-1 optical interface, C4 PDH interface)
Page 21
IF cable
Page 22
The RF unit is an outdoor unit (ODU). The IF, signal processing, and MUX/DEMUX units are integrated in the indoor unit (IDU). The ODU and IDU are connected through an IF cable.
The ODU can either be directly mounted onto the antenna or connected to the antenna through a short soft waveguide.
Although the capacity is smaller than the trunk, due to the easy installation and maintenance, fast network construction, its the most widely used microwave equipment.
Page 23
Unit Functions
Antenna: Focuses the RF signals transmitted by ODUs and increases the signal gain. ODU: RF processing, conversion of IF/RF signals. IF cable: Transmitting of IF signal, management signal and power supply of ODU. IDU: Performs access, dispatch, multiplex/demultiplex, and modulation/demodulation for services.
Page 24
ODU
IF port
Page 25
Parabolic antenna
z
Cassegrainian antenna
Antennas are used to send and receive microwave signals. Parabolic antennas and cassegrainian antennas are two common types of microwave antennas. Microwave antenna diameters includes: 0.3m, 0.6m, 1.2m, 1.8m,2.0m, 2.4m, 3.0m, 3.2metc.
Page 26
Different frequency channels in same frequency band can share one antenna.
Channel Tx Rx 1 1
Channel 1 1
Tx Rx
n n
n n
Page 27
Page 28
When antennas are poorly aligned, a small voltage may be detected in one direction. In this case, perform coarse adjustment on the antennas at both ends, so that the antennas are roughly aligned.
The antennas at both ends that are well aligned face a little bit upward. Though 12 dB is lost, reflection interference will be avoided.
Page 29
wrong adjustment cases are show here. One antenna is aligned to another antenna through the side lobe. As a result, the RSSI cannot meet the requirements.
Wrong
Wrong
Correct
Page 30
Antenna gain
Definition: Ratio of the input power of an isotropic antenna Pio to the input power of a parabolic antenna Pi when the electric field at a point is the same for the isotropic antenna and the parabolic antenna.
P D G = io = Pi
Half-power angle
Usually, the given antenna specifications contain the gain in the largest radiation (main lobe) direction, denoted by dBi. The half-power point, or the 3 dB point is the point which is deviated from the central line of the main lobe and where the power is decreased by half. The angle between the two half-power points is called the half-power angle.
0.5 = (65 0 ~ 70 0 )
D
Half-power angle
Page 31
Cross polarization discrimination Suppression ratio of the antenna receiving heteropolarizing waves, usually, larger than 30 dB.
XdB10lgPo/Px Po: Receiving power of normal polarized wave Px: Receiving power of abnormal polarized wave
Attenuation degree of the receiving capability in a direction of an antenna compared with that in the main lobe direction. An antenna protection ratio of 180 is called front-to-back ratio.
Page 32
ATPC
Power detection
RF loop
IF amplification
Filtering
Frequency mixing
Low-noise amplification
Bandpass filtering
Page 33
Specifications of Transmitter
Generally, trunk radios use 6, 7, and 8 GHz frequency bands. 11, 13 GHz and higher frequency bands are used in the access layer (e.g. BTS access).
Output power
The power at the output port of a transmitter. Generally, the output power is 15 to 30 dBm.
Page 34
If the working frequency of the transmitter is unstable, the demodulated effectived signal ratio will be decreased and the bit error ratio will be increased. The value range of the local frequency stability is 3 to 10 ppm.
The frequency spectrum of the transmitted signal must meet specified requirements, to avoid occupying too much bandwidth and thus causing too much interference to adjacent channels. The limitations to frequency spectrum is called transmit frequency spectrum frame.
Page 35
Specifications of Receiver
Receivers work together with transmitters. The receiving frequency on the local station is the transmitting frequency of the same channel on the opposite station. Local frequency stability
Page 36
Passband
To effectively suppress interference and achieve the best transmission quality, the passband and amplitude frequency characteristics should be properly chosen. The receiver passband characteristics depend on the IF filter.
Selectivity
Ability of receivers of suppressing the various interferences outside the passband, especially the interference from adjacent channels, image interference and the interference between transmitted and received signals.
Automatic control of receiver gain. With this function, input RF signals change within a certain range and the IF signal level remains unchanges.
Page 37
Subband C
Subband A
Subband B
Subband C
7442
7498
Non-primary station ODU specifications are related to radio frequencies. As one ODU cannot cover an entire frequency band, usually, a frequency band will be divided into several subbands and each subband corresponds to one ODU. z Different T/R spacing corresponds to different ODUs. z Primary and non-primary stations have different ODUs.
z
Primary station
Types of ODUs = Number of frequency bands x Number of T/R spacing x Number of subbands x 2 (ODUs of some manufacturers are also classified by capacity.
Page 38
Modulat ion
Tx IF
Demodu lation
Rx IF
From/to ODU
Cable interface
DC/DC conversion
Page 39
Questions
z
What types are microwave equipment classified into? What units do the split-mount microwave equipment have? And what are their functions?? How to adjust antennas? What are the key specifications of antennas? What are the key specifications of ODU transmitters and receivers? Can you describe the entire signal flow of microwave transmission?
Page 40
Summary
z z
Classification of digital microwave equipment Components of split-mount microwave equipment and their functions
z z z z
Antenna installation and key specifications of antennas Functional modules and key performance indexes of ODU Functional modules of IDU Signal flow of microwave transmission
Page 41
Contents
1. Digital Microwave Communication Overview 2. Digital Microwave Communication Equipment 3. Digital Microwave Networking and Application 4. Microwave Propagation and Anti-fading Technologies 5. Designing Microwave Transmission Links
Page 42
Page 43
Terminal station
Terminal station
Copyright 2006 Huawei Technologies Co., Ltd. All rights reserved. Page 44
Passive
Relay station
Active
Page 45
Radio Frequency relay station An active, bi-directional radio repeater system without frequency shift. The RF relay station directly amplifies the signal over radio frequency. Regenerator relay station A high-frequency repeater of high performance. The regenerator relay station is used to extend the transmission distance of microwave communication systems, or to deflect the transmission direction of the signal to avoid obstructions and ensure the signal quality is not degraded. After complete regeneration and amplification, the received signal is forwarded.
Page 46
The parabolic reflector passive relay station is composed of two parabolic The two-parabolic passive relay station often uses large-diameter antennas. The near end is less than 5 km away.
Page 47
Plane reflector passive relay station: A metal board which has smooth surface, proper effective area, proper angle and distance with the two communication points. It is also a passive relay microwave station. Full-distance free space loss:
d1(km) d 2(km)
a = A cos 2
a is the effective area (m2) of the flat reflector.
Page 48
Page 49
Page 50
Questions
z
What are the networking modes frequently used for digital microwave?
Page 51
Contents
1. Digital Microwave Communication Overview 2. Digital Microwave Communication Equipment 3. Digital Microwave Networking and Application 4. Microwave Propagation and Anti-fading Technologies 5. Designing Microwave Transmission Links
Page 52
Contents
4. Microwave Propagation and Anti-fading Technologies
4.1 Factors Affecting Electric Wave Propagation 4.2 Various Fading in Microwave Propagation 4.3 Anti-fading Technologies for Digital Microwave
Page 53
Fresnel zone: The sum of the distance from P to T and the distance from P to R
complies with the formula, TP+PR-TR= n/2 (n=1,2,3, ). The elliptical region encircled by the trail of P is called the Fresnel zone.
O F1 P d1 d2
Fresnel zone radius: The vertical distance from P to the TR line in the Fresnel zone. The
Page 54
F1 = 17.32
The first Fresnel zone is the region where the microwave transmission energy is the
most concentrated. The obstruction in the Fresnel zone should be as little as possible. With the increase of the Fresnel zone serial numbers, the field strength of the receiving point reduces as per arithmetic series.
Copyright 2006 Huawei Technologies Co., Ltd. All rights reserved. Page 55
Clearance
h3 h1 h4
A M
hc
F
hp
hs
B h5 h6 h2
d1
d2
Along the microwave propagation trail, the obstruction from buildings, trees, and mountain
peaks is sometimes inevitable. If the height of the obstacle enters the first Fresnel zone, additional loss might be caused. As a result, the received level is decreased and the transmission quality is affected. Clearance is used to avoid the case described previously.
The vertical distance from the obstacle to AB line segment is called the clearance of the
obstacle on the trail. For convenience, the vertical distance hc from the obstacle to the ground surface is used to represent the clearance. In practice, the error is not big because the line segment AB is approximately parallel to the ground surface. If the first Fresnel zone radius of the obstacle is F1, then hc/ F1 is the relative clearance.
Copyright 2006 Huawei Technologies Co., Ltd. All rights reserved. Page 56
The reflected wave from the ground surface is the major factor that affects the received level.
Smooth ground or water surface can reflect the part of the signal energy transmitted by the antenna to
the receiving antenna and cause interference to the main wave (direct wave). The vector sum of the reflected wave and main wave increases or decreases the composite wave. As a result, the transmission becomes unstable. Therefore, when doing microwave link design, avoid reflected waves as much as possible. If reflection is inevitable, make use of the terrain ups and downs to block the reflected waves.
Page 57
Different reflection conditions of different terrains have different effects on electric wave
Type A: mountains (or cities with dense buildings) Type B: hills (gently wavy ground surface) Type C: plain Type D: large-area water surface
The reflection coefficient of mountains is the smallest, and thus the mountain terrain is
most suitable for microwave transmission. The hill terrain is less suitable. When designing circuits, try to avoid smooth plane such as water surface.
Page 58
Troposphere indicates the low altitude atmosphere within 10 km from the ground.
Microwave antennas will not be higher than troposphere, so the electric wave propagation in aerosphere can be narrowed down to that in troposphere. Main effects of troposphere on electric wave propagation are listed below:
Absorption caused by gas resonance. This type of absorption can affect the
Absorption and scattering caused by rain, fog, and snow. This type of absorption
Page 59
Contents
4. Microwave Propagation and Anti-fading Technologies
4.1 Factors Affecting Electric Wave Propagation 4.2 Various Fading in Microwave Propagation 4.3 Anti-fading Technologies for Digital Microwave
Page 60
Fading: Random variation of the received level. The variation is irregular and the reasons for this are various.
Fading mechanism
Fading time
Received level
Down fading
K-type fading
Slow fading
Absorption fading
Fast fading
Flat fading
Scintillation fading
Rain fading
Up fading
Page 61
Free space loss: A = 92.4 + 20 log d + 20 log f (d: km, f: GHz). If d or f is doubled, the loss will increase by 6 dB.
d
GTX GRX
PTX = Transmit power PRX = Receive power G = Antenna gain A0 = Free space loss M = Fading margin
Power level
f
G A0 G
PTX
PRX M
Page 62
Absorption Fading
z
Molecules of all substances are composed of charged particles. These particles have their
own electromagnetic resonant frequencies. When the microwave frequencies of these substances are close to their resonance frequencies, resonance absorption occurs to the microwave.
z
Statistic shows that absorption to the microwave frequency lower than 12 GHz is smaller
than 0.1 dB/km. Compared with free space loss, the absorption loss can be ignored.
10dB
1dB
0.1dB
0.01dB
60GHz
23GHz
12GHz
7.5GHz
1GHz
Atmosphere absorption curve (dB/km) Copyright 2006 Huawei Technologies Co., Ltd. All rights reserved. Page 63
Rain Fading
z
For frequencies lower than 10 GHz, rain loss can be ignored. Only a few db may be
added to a relay section. For frequencies higher than 10 GHz, repeater spacing is mainly affected by rain loss.
For example, for the 13 GHz frequency or higher, 100 mm/h rainfall causes a loss of 5 dB/km. Hence, for the 13 GHz and 15 GHz frequencies, the maximum relay distance is about 10 km. For the 20 GHz frequency and higher, the relay distance is limited in few kilometres due to rain loss. High frequency bands can be used for user-level transmission. The higher the
Page 64
Atmosphere refraction
considered that the electromagnetic wave is propagated along a straight line above the earth with an equivalent earth radius of Re ,
The average measured K value is about 4/3. However, the K value of a specific
section is related to the meteorological phenomena of the section. The K value may change within a comparatively large range. This can affect line-of-sight propagation.
Re
R
Page 65
Microwave propagation
k = 1: No refraction
Page 66
Equivalent earth radius In temperate zones, the refraction when the K value is 4/3 is regarded as the standard refraction, where the atmosphere is the standard atmosphere and Re which is 4R/3 is the standard equivalent earth radius.
2/3 1 4/3 k=
Ground surface
Multipath fading: Due to multipath propagation of refracted waves, reflected waves, and scattered waves, multiple electric waves are received at the receiving end. The composition of these electric waves will result in severe interference fading. Reasons for multipath fading: reflections due to non-uniform atmosphere, water surface and smooth ground surface.
Down fading: fading where the composite wave level is lower than the free space received level. Up fading: fading where the composite wave level is higher than the free space received level.
z
Page 68
Multipath fading is caused by mutual interference between the direct wave and reflected wave (or diffracted wave on some conditions) with different phases.
Multipath fading grows more severe when the wave passes water surface or smooth
ground surface. Therefore, when designing the route, try to avoid smooth water and ground surface. When these terrains are inevitable, use the high and low antenna technologies to bring the reflection point closer to one end so as to reduce the impact of the reflected wave, or use the high and low antennas and space diversity technologies or the antennas that are against reflected waves to overcome multipath fading.
Page 69
Selective fading
Normal
Frequency (MHz)
Page 70
1h
Signal interruption
Page 71
Scintillation Fading
When the dielectric constant of local atmosphere is different from the ambient due to the particle clusters formed under different pressure, temperature, and humidity conditions, scattering occurs to the electric wave. This is called scintillation fading. The amplitude and phase of different scattered waves vary with the atmosphere. As a result, the composite field strength at the receiving point changes randomly. Scintillation fading is a type of fast fading which lasts a short time. The level changes little and the main wave is barely affected. Scintillation fading will not cause communications interruption.
Scintillation fading
Page 73
Summary
z
The higher the frequency is and the longer the hop distance is, the more severe the fading is. Fading is more severe at night than in the daylight, in summer than in winter. In the daylight, sunshine is good for air convection. In summer, weather changes frequently. In sunny days without wind, atmosphere is non-uniform and atmosphere subdivision easily forms and hardly clears. Multipath transmission often occurs in such conditions. Fading is more severe along water route than land route, because both the reflection coefficient of water surface and the atmosphere refraction coefficient above water surface are bigger.
Fading is more severe along plain route than mountain route, because atmosphere subdivision often occurs over plain and the ground reflection factor of the plain is bigger. Rain and fog weather causes much influence on high-frequency microwave.
Page 74
Contents
4. Microwave Propagation and Anti-fading Technologies
4.1 Factors Affecting Electric Wave Propagation 4.2 Various Fading in Microwave Propagation 4.3 Anti-fading Technologies for Digital Microwave
Page 75
Power reduction
Page 76
Slope equalization
The frequency domain equalization only equalizes the amplitude frequency response The circuit is simple.
Page 77
T C-n Before
C0
T Cn After
-2Ts
-Ts
Ts
-2Ts
-Ts
Ts
Page 78
Under normal propagation conditions, the output power of the transmitter is always at a lower level, for example, 10 to 15 dB lower than the normal level. When propagation fading occurs and the receiver detects that the propagation fading is lower than the minimum received level specified by ATPC, the RFCOH is used to let the transmitter to raise the transmit power.
z
ATPC
ATPC
Demodulator
Receiver
Transmitter
Modulator
Page 79
ATPC: The output power of the transmitter automatically traces and changes with the received level of the receiver within the control range of ATPC.
The time rate of severe propagation fading is usually small (<1%). After ATPC is configured, the transmitter works at a power 10 to 15 dB lower than the nominal power for over 99% of the time. In this way, adjacent channel interference and power consumption can be reduced.
Effects of ATPC:
Reduces the interference to adjacent systems and over-reach interference Reduces DC power consumption Reduces up fading Improves residual BER
Page 80
-25 -35 -45 -55 ATPC dynamic range Low level High level 31
21
-72 45
85
102
Page 81
used to transmit two different signals over one frequency. The utilization ratio of the frequency spectrum is doubled. To avoid severe interference between two different polarized signals, the interference compensation technology must be used.
Electric field direction
H (V)
Horizontal polarization
H (V) 1X 2X 3X 4X 5X 6X 7X 8X 1X 2X 3X' 4X 5X 6X 7X 8X
Page 82
Diversity technologies
For diversity, two or multiple transmission paths are used to transmit the same information and the receiver output signals are selected or composed, to reduce the effect of fading. Diversity has the following types, space diversity, frequency diversity, polarization diversity, and angle diversity.
Space diversity and frequency diversity are more frequently used. Space diversity is economical and has a good effect. Frequency diversity is often applied to multi-channel systems as it requires a wide bandwidth. Usually, the system that has one standby channel is configured with frequency diversity.
f1 f2
Frequency diversity
two or more microwave frequencies with certain frequency spacing to transmit and receive the same information which is then selected or composed, to reduce the influence of fading. This work mode is called frequency diversity.
Advantages: The effect is obvious. Only one antenna is required. Disadvantages: The utilization ratio of frequency bands is low.
f1 f2
Page 84
Signals have different multipath effect over different paths and thus have different fading characteristics. Accordingly, two or more suites of antennas at different altitude levels to receive the signals at the same frequency which are composed or selected. This work mode is called space diversity. If there are n pairs of antennas, it is called n-fold diversity. Advantages: The frequency resources are saved.
Disadvantages: The equipment is complicated, as two or more suites of antennas are required. Antenna distance: As per experience, the distance between the diversity antennas is 100 to 200 times the wavelength in frequently used frequency bands. f1
f1
Page 85
Tx
nl
l/2
Rx
Dh h1
d
z
Dh =
(nll/2)d
2h1
Page 86
l: wavelength d: path distance h1: height of the antenna at the transmit end
Apart from the anti-fading technologies introduced previously, here are two frequently Method I: Make use of some terrain and ground objects to block reflected waves.
used tips:
z
Page 87
Page 88
Hybrid coupler
With one hybrid coupler added between two ODUs and the antenna, the 1+1 HSB can be realized in the configuration of one antenna. Moreover, the FD technology can also be adopted.
z
The 1+1 HSB can also be realized in the configuration of two antennas. In this case, the FD and SD technologies can both be adopted, which improves the system availability.
z
Page 89
In the following figure, Mn stands for the active channel and P stands for the standby channel. The active channel and the standby channel have their independent modulation/demodulation unit and signal transmitting /receiving unit.
When the fault or fading occurs in the active channel, the signal is switched to the standby channel. The channel backup is an inter-frequency backup. This protection mode (FD) is mainly used in the all indoor microwave equipment.
M1 M2 M3 P
M1 M2 M3 P
RFSOH
Page 90
Equipment protection and channel protection Equipment protection and channel protection Equipment protection and channel protection
Select the proper mode depending on the geographical condition and requirements of the customer
1+1
FD+SD
N+1
FD
Page 91
Questions
z
What factors can affect the microwave propagation? What types of fading exists in the microwave propagation? What are the two categories is the anti-fading technology? What protection modes are available for the microwave?
Page 92
Summary
z z z
Importance parameters affecting microwave propagation Various factors affecting microwave propagation Various fading types in the microwave propagation (free space propagation fading, atmospheric absorption fading, rain or fog scattering fading, K type fading, multipath fading, duct type fading, and scintillation type fading)
z z
Anti-fading technologies Anti-fading measures adopted on the equipment: adaptive equalization, ATPC, and XPIC
z z
Anti-fading measures adopted in the system: FD and SD Protection modes of the microwave equipment
Page 93
Contents
1. Digital Microwave Communication Overview 2. Digital Microwave Communication Equipment 3. Digital Microwave Networking and Application 4. Microwave Propagation and Anti-fading Technologies 5. Designing Microwave Transmission Links
Page 94
Contents
5. Designing Microwave Transmission Links
5.1 Basis of Designing a Microwave Transmission Line 5.2 Procedures for Designing a Microwave Transmission Line
Page 95
Transmission clearance
Page 96
Line propagation
Page 97
In the microwave transmission, the transmit power is very small, only the antenna in the accurate direction can realize the communication. For the communication of long distance, use the antenna of greater diameter or increase the transmit power.
3 dB
Page 98
In common geographical conditions, it is recommended that there be no obstacles within the first Fresnel zone if K is equal to 4/3. When the microwave transmission line passes the water surface or the desert area, it is recommended that there are no obstacles within the first Fresnel zone if K is equal to 1. The first Fresnel zone
k = 4/3
Page 99
The knife-edged obstacle blocks partial of the Fresnel zone. This also causes the
diffraction of the microwave. Influenced by the two reasons, the level at the actual receive point must be lower than the free space level. The loss caused by the knifeedged obstacle is called additional loss.
Page 100
connecting the transmit end and the receive end, that is, the HC is equal to 0, the additional loss is equal to 6 dB.
z
-4 -6 -8 -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -2.5-2.0-1.5-1.0-0.5 0 0.51.0 1.5 2.0 2.5 HC/F1 Loss caused by block of knife-edged obstacle
connecting the transmit end the receive end, the additional loss fluctuates around 0 dB. The transmission loss in the path and the signal receiving level approach the values in the free space transmission.
Page 101
Clearance calculation
h1d 2 + h2 d1 hc = hb hs d
The value of clearance is required greater than that of the first Fresnel Zones radius.
hc
h2
h1
d1
hs
hb
d2
Page 102
To present the influence of various factors on microwave transmission, the field strength
fading factor V is introduced. The field strength fading factor V is defined as the ratio of the combined field strength when the irradiated wave and the reflected wave arrive at the receive point to the field strength when the irradiated wave arrives at the receive point in the free space transmission.
h E 2 ce V = = 1 + 2 cos E0 F 1
arrive at the receive point E0 : Field strength when the irradiated wave arrives at the received point in the free space transmission : Equivalent ground reflection factor
E: Combined field strength when the irradiated wave and reflected wave
Page 103
can be
VdB 10
influence of the earth considered, HC/F1 is equal to 0.577 when the signal receiving level is equal to the free space level the first time.
approximately equal to 0.6 when the signal receiving level is equal to the free space level the first time.
clearance is called the free space clearance, represented by H0 and expressed in the following formula: H0 = 0.577F 1 = (d1d2/d)1/2
Page 104
To make the clearance cost-effective and reasonable in the engineering, the height of the antenna should be adjusted according to the following requirements.
In the case that is not greater than 0.5, that is, for the circuit that passes the area of small ground reflection factor like the mountainous area, city, and hilly area, to avoid over great diffraction, the height of the antenna should be adjusted according to the following requirements: When K = 2/3, HC 0.3F1 (for common obstacles) HC 0 (for knife-shaped obstacles)
Page 105
In the case that is greater than 0.7, that is, for the circuit that passes the area of great
ground reflection factor like the plain area and water reticulation area, to avoid over great reflection fading, the height of the antenna should be adjusted according to the following requirements When K = 2/3, HC 0.3F1 (for common obstacles) HC 0 (for knife-edged obstacles) When K = 4/3, HC F1 When K = , HC 1.35F1 (The deep fading occurs when HC = 21/2 F1.)
If these requirements cannot be met, change the height of the antenna or the route.
Page 106
Page 107
Determine the route according to engineering map. We should select the area that rolls as much as possible, such as the hilly area. We should avoid passing the water surface and the flat and wide area that is not suitable for the transmission of the electric wave. In this way, the strong reflection signal and the accordingly caused deep fading can be avoided. The line should avoid crossing through or penetrating into the mountainous area. The line should go along with the railway, road and other areas with the convenient transportation.
Page 108
Select the site of the microwave station. The distance between two sites should not be too long. The distance between two relay stations should be equal, and each relay section should have the proper clearance.
Select the Z route to avoid the over-reach interference. Avoid the interference from other radio services, such as the satellite communication system, radar site, TV station, and broadcast station.
f1 f2 f1 f2 Over-reach interference f1 f2
The signal from the first microwave station interferes with the signal of the same frequency from the third microwave station.
Page 109
Draw the cross-sectional chart of the terrain. Draw the cross-sectional chart of the terrain based on the data of each site. Calculate the antenna height and transmission situation of each site. For the line that has strong reflection, adjust the mounting height of the antenna to block the reflected wave, or have the reflection point fall on the earth surface with small reflection factor.
Consider the path clearance. The clearance in the plain area should not be over great, and that in the mountainous area should not be over small.
Page 110
Calculate the parameters for site construction. Calculate the terrain parameters when the route and the site are already determined. Calculate the azimuth and the elevation angles of the antenna, distance between sites, free space transmission loss and receive level, rain fading index, line interruption probability, and allocated values and margin of the line index. When the margin of the line index is eligible, plan the equipment and frequencies, make the approximate budget, and deliver the construction chart.
Input
There is special network planning software, and the commonly used is CTE Pathloss.
Input
Page 111
Questions
z
What are the requirements for microwave communication? What is the goal of microwave design? What extra factors should be taken into consideration for microwave planning? Can you tell the procedure for designing a microwave transmission line?
Page 112
Thank You
www.huawei.com