Professional Documents
Culture Documents
Huawei 3G Iub Satellite Transmission Configuration in RNC
Huawei 3G Iub Satellite Transmission Configuration in RNC
Huawei 3G Iub Satellite Transmission Configuration in RNC
Draft 2008-03-20
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. For any assistance, please contact our local office or company headquarters.
Website: Email:
Copyright Huawei Technologies Co., Ltd. 2008. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.
Notice
The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but the statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied.
Contents
Contents
About This Document.....................................................................................................................1 1 Change History of Iub Satellite Transmission.....................................................................1-1 2 Introduction to Iub Satellite Transmission...........................................................................2-1 3 Technical Description of Iub Satellite Transmission.........................................................3-1
3.1 Iub Satellite Transmission Parameters............................................................................................................3-2 3.2 Structure of Iub Satellite Transmission...........................................................................................................3-5 3.3 Networking for Iub Satellite Transmission.....................................................................................................3-7 3.4 Bands for Iub Satellite Transmission..............................................................................................................3-7 3.5 Iub Satellite Transmission Algorithm.............................................................................................................3-8
5 Maintenance Information About Iub Satellite Transmission...........................................5-1 6 Reference Documents About Iub Satellite Transmission..................................................6-1
Figures
Figures
Figure 3-1 Structure of Iub satellite transmission................................................................................................3-6 Figure 3-2 VSAT system on the Iub interface.....................................................................................................3-7 Figure 3-3 Protocol stack for the Iub interface (based on ATM and IP)..............................................................3-8
iii
Tables
Tables
Table 1-1 Document and product versions...........................................................................................................1-1 Table 2-1 NEs involved in Iub satellite transmission...........................................................................................2-1 Table 2-2 RAN products and related versions......................................................................................................2-2 Table 3-1 Parameters related to Iub satellite transmission...................................................................................3-2 Table 3-2 Bands for satellite transmission...........................................................................................................3-8
1
Document Version Draft (2008-03-20)
Change History of Iub Satellite Transmission describes the changes in different document versions.
Feature change: refers to the change in the data integrity protection and encryption feature of a specific product version. Editorial change: refers to the change in the information that was inappropriately described or the addition of the information that was not described in the earlier version.
Draft (2008-03-20)
This is the draft of the document for first commercial release of RAN10.0. Compared with issue 02 (2007-12-24) of RAN6.1, this issue has no feature change or editorial change.
1-1
Introduction
Definition In general, the data between the RNC and the NodeB is transmitted on terrestrial transport networks that can be based on PDH, SDH, MSTP, ATM, or IP. In some remote areas, coastal islands, deserts, and uninhabited areas where terrestrial transport networks are unavailable or difficult to deploy, satellite transmission can overcome this difficulty. Purposes Since satellite communication has many benefits such as larger coverage, minor influence by landforms, good mobility for emergency communications, easy link leasing or deployment, and easy bandwidth control, Iub satellite transmission makes the Iub interface easier to deploy. Satellite communication, however, has demerits such as high costs in equipment and link leasing, and high delay. Therefore, the Iub satellite transmission is recommended only when terrestrial transport is unavailable.
Availability
Network Elements Involved Table 2-1 describes the Network Elements (NEs) involved in the Iub satellite transmission feature. Table 2-1 NEs involved in Iub satellite transmission UE
NOTE
l : not involved l : involved
NodeB
RNC
MSC Server
MGW
SGSN
GGSN
HLR
2-1
Software Releases Table 2-2 describes the versions of RAN products that support Iub satellite transmission. Table 2-2 RAN products and related versions Product RNC BSC6800 BSC6810 NodeB DBS3800 BTS3812E BTS3812A iDBS3800 BTS3812AE V100R008 and later releases Version V100R005 and later releases V200R009 and later releases V100R005 and later releases
Miscellaneous None.
Impact
Impact on System Performance The feature has the following impact on system performance.
l
Satellite transmission quality is liable to environmental conditions. Bit errors may lead to bad quality in calls and data services, lower efficiency in transmission, or even call failures. The delay of satellite transmission is higher than that of terrestrial transmission. Satellite transmission usually brings about the Round Trip Time (RTT) in the range of 500 ms to 700 ms. Long delay or RTT may cause slow call connections or voice delay and affect the downloading of high-speed data services.
Capabilities
None.
2-2
3-1
ADD NODEB MOD NODEB ADD NODEB MOD NODEB SET SATLDM
RNC
RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
Global Global
RNC RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
3-2
Parameter Name Period common measure protect timer coeff LDB moving average filter length PUC moving average filter length UL LDR moving average filter length DL LDR moving average filter length UL OLC moving average filter length DL OLC moving average filter length UL CAC moving average filter length DL CAC moving average filter length Time unit of HSDPA need pwr meas cycle
Command
SET SATLDM
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
3-3
Parameter Name HSDPA need pwr meas cycle[10ms] HSDPA need pwr meas cycle[m] HSDPA need power filter len Time unit of HSDPA bit rate meas cycle HSDPA bit rate meas cycle[10ms] HSDPA bit rate meas cycle[m] HSDPA bit rate filter len Max measure continuous invalid times UL overload measure filter coeff Time unit for UL OLC meas rprt cycle UL OLC meas rprt cycle [10ms] UL OLC meas rprt cycle[m] UL OLC trigger hysteresis [10ms]
Command
SET SATLDM
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
Global Global
RNC RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
Global Global
RNC RNC
3-4
Parameter Name DL overload measure filter coeff Time unit for DL OLC meas rprt cycle DL OLC meas rprt cycle [10ms] DL OLC meas rprt cycle[m] DL OLC trigger hysteresis [10ms] Intrafrequency LDB period timer length [s] PUC period timer length [s] LDR period timer length [s] OLC period timer length [ms]
Command
SET SATLDM
SET SATLDM
Global
RNC
SET SATLDM
Global
RNC
Global Global
RNC RNC
SET SATLDCPERIOD
Global
RNC
SET SATLDCPERIOD
Global
RNC
SET SATLDCPERIOD
Global
RNC
SET SATLDCPERIOD
Global
RNC
3-5
Communications Satellite
The communications satellite usually refers to a geosynchronous satellite. The satellite orbits at a distance of 36,000 km from the earth and has an angular orbital velocity equal to the earth orbital velocity. A communications satellite consists of the control system, communication system (antennas and repeaters), telemeter system, power supply system, and temperature control system.
Earth Station
An earth station consists of the antenna system, transceiver, channel terminal (modem), communication control system, and power supply system.
NOTE
l l l l
The interface between an earth station and the RNC or NodeB should comply with the ITU-T G.703 recommendations. The RNC or NodeB can communicate with the earth station through the E1 or channelized STM-1 interface board. The E1 interface board is recommended. The RNC or NodeB and the earth station can transmit signals to each other in PDH or SDH or microwave mode. The RNC or NodeB supports fractional ATM or fractional IP technology for satellite communication.
A large-scale earth station, such as a large-scale national or international communication station, uses the large-aperture antenna to transmit high-speed data. A large-scale earth station brings the high cost. User data should be converged on the earth station through terrestrial communication networks before satellite communication. A small-scale earth station, such as a Very Small Aperture Terminal (VSAT), uses the small-aperture antenna. The equipment features low cost and easy deployment.
Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd Issue Draft (2008-03-20)
3-6
Table 3-2 describes two typical bands for satellite transmission. Table 3-2 Bands for satellite transmission Band C Frequency
l l
Characteristic
l l l l
Insensitive to atmospheric absorption Insensitive to rainfall Sensitive to the terrestrial microwave communication at the same band Large antenna aperture Sensitive to rainfall, snowfall and fog Insensitive to the terrestrial microwave communication at the same band Small antenna aperture Flexible applications
Ku
l l
l l l l
3-8
Compared with terrestrial transmission, the Round Trip Time (RTT) value on the Iub interface in satellite transmission mode increases by 500 ms to 700 ms. Consequently, the Uu interface RTT value carried on the Iub interface increases by 500 ms to 700 ms. The optimum Uu and Iub parameters should be used in this environment. If the Iub satellite transmission is enabled, the RNC provides default values of the following parameters for the NodeB using satellite transmission:
l l
Load Monitor (LDM) and Load Control (LDC) parameters Optimum parameters related to the sliding window size and timer of the RLC at the data link layer Optimum parameters of the FP transport synchronization timer Optimum activation time of radio links Optimum outer loop power control parameters (to prevent voice and data quality from control hysteresis) Constraining the handover procedure (If the delay variation is out of the soft combination range during soft handover, only hard handover is allowed.)
l l l
If the Iub satellite transmission is disabled, the RNC denies the NodeB using satellite transmission. The following parameters are associated with Iub satellite transmission.
NOTE
The default parameters of the SSCOP/ALCAP/NBAP timers can meet the requirement of satellite transmission. They need not be reconfigured.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command
Description
This parameter indicates initial RTT that is used for initial FP transport synchronization. It can be set to a higher value than the actual value. The accurate RTT is measured by the FP transport synchronization procedures.
GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command
Description
This parameter indicates whether the satellite transmission can be applied to the Iub interface.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
UL basic common measure filter coeff UlBasicCommMeasFilterCoeff D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17, D19 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3 Optional SET SATLDM This parameter indicates the filter coefficient for UL basic common measurement. The greater this parameter is, the greater the smoothing effect and the higher the anti slow attenuation capability, but the lower the signal tracing capability.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory
Time unit for UL basic meas rprt cycle ChoiceRprtUnitForUlBasicMeas TEN_MSEC, MIN 10 ms, 1 min TEN_MSEC Optional
3-10
SET SATLDM This parameter indicates the time unit of report period for UL basic measurement.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
UL basic meas rprt cycle[10ms] TenMsecForUlBasicMeas 1 to 6000 10 ms to 60000 ms Step: 10 100 Optional SET SATLDM This parameter indicates the report period for UL basic measurement. The time unit is ms.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
UL basic meas rprt cycle[m] MinForUlBasicMeas 1 to 60 1 min to 60 min None Optional SET SATLDM This parameter indicates the report period for UL basic measurement. The time unit is min.
DL basic common measure filter coeff DlBasicCommMeasFilterCoeff D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17, D19
3-11
Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3 Optional SET SATLDM This parameter indicates the filter coefficient for DL basic common measurement. The greater this parameter is, the greater the smoothing effect and the higher the anti slow attenuation capability, but the lower the signal tracing capability.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
Time unit for DL basic meas rprt cycle ChoiceRprtUnitForDlBasicMeas TEN_MSEC, MIN 10 ms, 1 min TEN_MSEC Optional SET SATLDM This parameter indicates the time unit of report period for DL basic measurement.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
DL basic meas rprt cycle[10ms] TenMsecForDlBasicMeas 1 to 6000 10 ms to 60000 ms Step: 10 100 Optional SET SATLDM This parameter indicates the report period for DL basic measurement. The time unit is ms.
3-12
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
DL basic meas rprt cycle[m] MinForDlBasicMeas 1 to 60 1 min to 60 min None Optional SET SATLDM This parameter indicates the report period for DL basic measurement. The time unit is min.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
Period common measure protect timer coeff PeriodProtectTimerCoeff 2 to 65535 2 to 65535 Step: 1 150 Optional SET SATLDM This parameter indicates the protect timer coefficient for periodical common measurement.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory
3-13
SET SATLDM This parameter indicates the length of the smoothing filter window for intra-frequency Load Balancing (LDB).
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
PUC moving average filter length PucAvgFilterLen 1 to 32 1 to 32 Step: 1 32 Optional SET SATLDM This parameter indicates the length of the smoothing filter window for Potential User Control (PUC).
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
UL LDR moving average filter length UlLdrAvgFilterLen 1 to 32 1 to 32 Step: 1 25 Optional SET SATLDM This parameter indicates the length of the smoothing filter window for UL Load Reshuffling (LDR).
3-14
Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
1 to 32 Step: 1 25 Optional SET SATLDM This parameter indicates the length of the smoothing filter window for DL Load Reshuffling (LDR).
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
UL OLC moving average filter length UlOlcAvgFilterLen 1 to 32 1 to 32 Step: 1 25 Optional SET SATLDM This parameter indicates the length of the smoothing filter window for UL Overload Congestion Control (OLC).
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
DL OLC moving average filter length DlOlcAvgFilterLen 1 to 32 1 to 32 Step: 1 25 Optional SET SATLDM This parameter indicates the length of the smoothing filter window for DL Overload Congestion Control (OLC).
3-15
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
UL CAC moving average filter length UlCacAvgFilterLen 1 to 32 1 to 32 Step: 1 3 Optional SET SATLDM This parameter indicates the length of the smoothing filter window for UL Call Admission Control (CAC).
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
DL CAC moving average filter length DlCacAvgFilterLen 1 to 32 1 to 32 Step: 1 3 Optional SET SATLDM This parameter indicates the length of the smoothing filter window for DL Call Admission Control (CAC).
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory
Time unit of HSDPA need pwr meas cycle ChoiceRprtUnitForHsdpaPwrMeas TEN_MSEC, MIN 10 ms, 1 min TEN_MSEC Optional
3-16
SET SATLDM This parameter indicates the time unit of report period for HSDPA power requirement measurement.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
HSDPA need pwr meas cycle[10ms] TenMsecForHsdpaPwrMeas 1 to 6000 10 ms to 60000 ms Step: 10 100 Optional SET SATLDM This parameter indicates the report period for HSDPA power requirement measurement. The time unit is ms.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
HSDPA need pwr meas cycle[m] MinForHsdpaPwrMeas 1 to 60 1 min to 60 min None Optional SET SATLDM This parameter indicates the report period for HSDPA power requirement measurement. The time unit is min.
3-17
Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
1 to 32 1 Optional SET SATLDM This parameter indicates the length of the smoothing filter window for HSDPA power requirement measurement.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
Time unit of HSDPA bit rate meas cycle ChoiceRprtUnitForHsdpaRateMeas TEN_MSEC, MIN 10 ms, 1 min TEN_MSEC Optional SET SATLDM This parameter indicates the time unit of measurement period for HSDPA bit rate.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
HSDPA bit rate meas cycle[10ms] TenMsecForHsdpaPrvidRateMeas 1 to 6000 10 ms to 60000 ms; step:10 100 Optional SET SATLDM This parameter indicates the measurement period for HSDPA bit rate. The time unit is ms.
3-18
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
HSDPA bit rate meas cycle[m] MinForHsdpaPrvidRateMeas 1 to 60 1 min to 60 min None Optional SET SATLDM This parameter indicates the measurement period for HSDPA bit rate. The time unit is min.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
HSDPA bit rate filter len HsdpaPrvidBitRateFilterLen 1 to 32 1 to 32 1 Optional SET SATLDM This parameter indicates the length of the smoothing filter window for HSDPA bit rate.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command
Max measure continuous invalid times MaxMeasContInvalidTimes 2 to 255 2 to 255 3 Optional SET SATLDM
3-19
Description
This parameter indicates the maximum allowed times of continuous invalid measurement.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
UL overload measure filter coeff UlOlcMeasFilterCoeff D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17, D19 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D1 Optional SET SATLDM This parameter indicates the filter coefficient for UL overload measurement. The greater this parameter is, the greater the smoothing effect and the higher the anti slow attenuation capability, but the lower the signal change tracing capability.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
Time unit for UL OLC meas rprt cycle ChoiceRprtUnitForUlOlcMeas TEN_MSEC, MIN 10 ms, 1 min TEN_MSEC Optional SET SATLDM This parameter indicates the time unit of report period for UL Overload Control (OLC) measurement.
3-20
Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
10 ms to 60000 ms; step:10 100 Optional SET SATLDM This parameter indicates the report period for UL OLC measurement. The time unit is ms.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
UL OLC meas rprt cycle[m] MinForUlOlcMeas 1 to 60 1 min to 60 min None Optional SET SATLDM This parameter indicates the report period for UL OLC measurement. The time unit is min.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
UL OLC trigger hysteresis[10ms] UlOlcTrigHyst 1 to 6000 10 ms to 60000 ms Step: 10 100 Optional SET SATLDM This parameter indicates the delay before reporting the UL OLC event.
3-21
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
DL overload measure filter coeff DlOlcMeasFilterCoeff D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17, D19 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D1 Optional SET SATLDM This parameter indicates the filter coefficient for DL overload measurement. The greater this parameter is, the greater the smoothing effect and the higher the anti slow attenuation capability, but the lower the signal change tracing capability.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
Time unit for DL OLC meas rprt cycle ChoiceRprtUnitForDlOlcMeas TEN_MSEC, MIN 10 ms, 1 min TEN_MSEC Optional SET SATLDM This parameter indicates the time unit of report period for DL OLC measurement.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value
DL OLC meas rprt cycle[10ms] TenMsecForDlOlcMeas 1 to 6000 10 ms to 60000 ms; Step: 10 100
3-22
Optional SET SATLDM This parameter indicates the report period for DL OLC measurement. The time unit is ms.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
DL OLC meas rprt cycle[m] MinForDlOlcMeas 1 to 60 1 min to 60 min None Optional SET SATLDM This parameter indicates the report period for DL OLC measurement. The time unit is min.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
DL OLC trigger hysteresis[10ms] DlOlcTrigHyst 1 to 6000 10 ms to 60000 ms Step:10 10 Optional SET SATLDM This parameter indicates the delay before reporting the DL OLC event.
3-23
GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
1 to 86400 1 s to 86400 s 1800 Optional SET SATLDCPERIOD This parameter indicates the period for Intra-frequency LDB.
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
PUC period timer length[s] PucPeriodTimerLen 6 to 86400 6 s to 86400 s 1800 Optional SET SATLDCPERIOD This parameter indicates the period for Potential User Control (PUC).
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
LDR period timer length[s] LdrPeriodTimerLen 1 to 86400 1 s to 86400 s 10 Optional SET SATLDCPERIOD This parameter indicates the period for Load Reshuffling (LDR).
3-24
Parameter Name Parameter ID GUI Range Physical Range and Unit Default Value Optional/ Mandatory MML Command Description
OLC period timer length[ms] OlcPeriodTimerLen 100 to 86400000 100 ms to 86400000 ms 3000 Optional SET SATLDCPERIOD This parameter indicates the period for Overload Control (OLC).
3-25
4-1
Procedure
l Enabling Iub satellite transmission 1. 2. l Configure transport layer data according to the terrestrial transmission status. Run the ADD NODEB command to add a NodeB. Set the value of IUB Trans Delay [ms], and set Satellite Trans Ind to TRUE.
----End
Example
// Enable Iub satellite transmission
ADD NODEB: TnlBearerType=ATM_TRANS, TRANSDELAY=10, SATELLITEIND=TRUE;
Context
NOTE
The Load Monitor (LDM) parameters and the Load Control (LDC) parameters can either be set by default or be manually reconfigured through the MML commands.
Procedure
Step 1 Run the MOD NODEB command to reconfigure IUB Trans Delay[ms] of a satellite-based NodeB. Step 2 Run the SET SATLDM command to reconfigure the Load Monitor (LDM) parameters. Step 3 Run the SET SATLDCPERIOD command to reconfigure the Load Control (LDC) parameters. ----End
Procedure
Disabling Iub satellite transmission There are two ways to disable Iub satellite transmission.
Run the MOD NODEB command to set Satellite Trans Ind to FALSE. Remove the concerned NodeBs.
----End
Example
Disable Iub satellite transmission
MOD NODEB: SATELLITEIND=FALSE;
4-3
5
Alarms
None.
This describes the alarms and counters related to Iub satellite transmission.
Counters
None.
5-1
3GPP TS 25.402: "Synchronization in UTRAN, Stage 2" 3GPP TS 25.430: "UTRAN Iub Interface: General Aspects and Principles" 3GPP TS 25.431: "UTRAN Iub Interface: Layer 1" 3GPP TS 25.432: "UTRAN Iub Interface: Signalling Transport" 3GPP TS 25.433: "NBAP Specification" 3GPP TS 25.434: "UTRAN Iub Interface: Data Transport & Transport Signalling for Common Transport Channel Data Streams" 3GPP TS 25.435: "UTRAN Iub Interface: User Plane Protocols for Common Transport Channel Data Streams" 3GPP TS 25.426: "UTRAN Iur/Iub Interface: Data Transport & Transport Signalling for DCH Data Streams" 3GPP TS 25.427: "UTRAN Iur/Iub Interface: User Plane Protocol for DCH Data Streams" 3GPP TS 25.322: "Radio Link Control (RLC) Protocol Specification" ITU-T Recommendation Q.2110 (07/94): "B-ISDN ATM adaptation layer Service specific connection oriented protocol (SSCOP)"
l l l
6-1