Professional Documents
Culture Documents
Structural Concepts and Systems For Architects
Structural Concepts and Systems For Architects
LECTURE NOTES
Dept. of Civil Environmental and Architectural Engineering University of Colorado, Boulder, CO 80309-0428
April 30, 1997
Draft 0{2
In order to invent a structure and to give it exact proportions, one must follow both the intuitive and the mathematical paths.
-Pier Luigi Nervi
Victor Saouma
Draft
Contents
1 INTRODUCTION
1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 Science and Technology : : : : : : Structural Engineering : : : : : : : Structures and their Surroundings Architecture & Engineering : : : : Architectural Design Process : : : Architectural Design : : : : : : : : Structural Analysis : : : : : : : : : Structural Design : : : : : : : : : : Load Transfer Mechanisms : : : : Structure Types : : : : : : : : : : Structural Engineering Courses : : References : : : : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: 1{1 : 1{1 : 1{1 : 1{2 : 1{2 : 1{2 : 1{3 : 1{3 : 1{4 : 1{4 : 1{12 : 1{13 : 2{1 : 2{1 : 2{2 : 2{2 : 2{4 : 2{5 : 2{5 : 2{5 : 2{9 : 2{11 : 2{14 : 2{16 : 2{18 : 2{18 : 2{18 : 2{19 : 2{19 : 2{20 : 2{20 : 2{21 : 2{21 : 2{21 : 2{25
1{1
2 LOADS
2.1 Introduction : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2.2 Vertical Loads : : : : : : : : : : : : : : : : : : : : : : : : : : : 2.2.1 Dead Load : : : : : : : : : : : : : : : : : : : : : : : : 2.2.2 Live Loads : : : : : : : : : : : : : : : : : : : : : : : : E 2-1 Live Load Reduction : : : : : : : : : : : : : : : : : : : 2.2.3 Snow : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2.3 Lateral Loads : : : : : : : : : : : : : : : : : : : : : : : : : : : 2.3.1 Wind : : : : : : : : : : : : : : : : : : : : : : : : : : : E 2-2 Wind Load : : : : : : : : : : : : : : : : : : : : : : : : 2.3.2 Earthquakes : : : : : : : : : : : : : : : : : : : : : : : : E 2-3 Earthquake Load on a Frame : : : : : : : : : : : : : : E 2-4 Earthquake Load on a Tall Building, (Schueller 1996) 2.4 Other Loads : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2.4.1 Hydrostatic and Earth : : : : : : : : : : : : : : : : : : E 2-5 Hydrostatic Load : : : : : : : : : : : : : : : : : : : : : 2.4.2 Thermal : : : : : : : : : : : : : : : : : : : : : : : : : : E 2-6 Thermal Expansion/Stress (Schueller 1996) : : : : : : 2.5 Other Important Considerations : : : : : : : : : : : : : : : : 2.5.1 Load Combinations : : : : : : : : : : : : : : : : : : : : 2.5.2 Load Placement : : : : : : : : : : : : : : : : : : : : : 2.5.3 Load Transfer : : : : : : : : : : : : : : : : : : : : : : : 2.5.4 Structural Response : : : : : : : : : : : : : : : : : : : 2.5.5 Tributary Areas : : : : : : : : : : : : : : : : : : : : :
2{1
Draft 0{2
3 STRUCTURAL MATERIALS
3.1 Steel : : : : : : : : : : : 3.1.1 Structural Steel : 3.1.2 Reinforcing Steel 3.2 Aluminum : : : : : : : : 3.3 Concrete : : : : : : : : : 3.4 Masonry : : : : : : : : : 3.5 Timber : : : : : : : : : 3.6 Steel Section Properties 3.7 Joists : : : : : : : : : : 4.1 4.2 4.3 4.4 4.5 Materials, & Geometry : Loads : : : : : : : : : : Reactions : : : : : : : : Internal Forces : : : : : Internal Stresses : : : :
CONTENTS
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 3{1 : 3{1 : 3{5 : 3{6 : 3{6 : 3{7 : 3{7 : 3{8 : 3{17 : 4{1 : 4{3 : 4{4 : 4{6 : 4{8 : 5{1 : 5{1 : 5{3 : 5{3 : 5{4 : 5{5 : 5{5 : 5{6 : 5{7 : 5{8 : 5{8 : 5{9 : 5{9 : 5{10 : 5{12 : 5{14 : 5{14 : 5{14 : 5{15 : 5{16 : 5{18 : 5{18 : 5{19 : 5{22 : 5{24 : 5{26 : 5{28 : 5{37 : 5{37 : 5{39 : 5{39 : 5{39
3{1
4{1
5 REVIEW of STATICS
5.1 Reactions : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 5.1.1 Equilibrium : : : : : : : : : : : : : : : : : : : : : : : : 5.1.2 Equations of Conditions : : : : : : : : : : : : : : : : : 5.1.3 Static Determinacy : : : : : : : : : : : : : : : : : : : : 5.1.4 Geometric Instability : : : : : : : : : : : : : : : : : : : 5.1.5 Examples : : : : : : : : : : : : : : : : : : : : : : : : : E 5-7 Simply Supported Beam : : : : : : : : : : : : : : : : : E 5-8 Three Span Beam : : : : : : : : : : : : : : : : : : : : E 5-9 Three Hinged Gable Frame : : : : : : : : : : : : : : : 5.2 Trusses : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 5.2.1 Assumptions : : : : : : : : : : : : : : : : : : : : : : : 5.2.2 Basic Relations : : : : : : : : : : : : : : : : : : : : : : 5.2.3 Determinacy and Stability : : : : : : : : : : : : : : : : 5.2.4 Method of Joints : : : : : : : : : : : : : : : : : : : : : E 5-10 Truss, Method of Joints : : : : : : : : : : : : : : : : : 5.3 Shear & Moment Diagrams : : : : : : : : : : : : : : : : : : : 5.3.1 Theory : : : : : : : : : : : : : : : : : : : : : : : : : : 5.3.1.1 Design Sign Conventions : : : : : : : : : : : 5.3.1.2 Load, Shear, Moment Relations : : : : : : : 5.3.1.3 Moment Envelope : : : : : : : : : : : : : : : 5.3.1.4 Examples : : : : : : : : : : : : : : : : : : : : E 5-11 Simple Shear and Moment Diagram : : : : : : : : : : E 5-12 Frame Shear and Moment Diagram : : : : : : : : : : : E 5-13 Frame Shear and Moment Diagram Hydrostatic Load E 5-14 Shear Moment Diagrams for Frame : : : : : : : : : : : E 5-15 Shear Moment Diagrams for Inclined Frame : : : : : : 5.3.2 Formulaes : : : : : : : : : : : : : : : : : : : : : : : : : 5.4 Flexure : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 5.4.1 Basic Kinematic Assumption Curvature : : : : : : : : 5.4.2 Stress-Strain Relations : : : : : : : : : : : : : : : : : : 5.4.3 Internal Equilibrium Section Properties : : : : : : : : 5.4.3.1 Fx = 0 Neutral Axis : : : : : : : : : : : :
5{1
Victor Saouma
Draft CONTENTS
5.4.3.2 M = 0 Moment of Inertia : : : : : : : : : : : 5.4.4 Beam Formula : : : : : : : : : : : : : : : : : : : : : : : : E 5-16 Design Example : : : : : : : : : : : : : : : : : : : : : : : 5.4.5 Approximate Analysis : : : : : : : : : : : : : : : : : : : : E 5-17 Approximate Analysis of a Statically Indeterminate beam
0{3
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 5{39 : 5{40 : 5{40 : 5{42 : 5{45 : 6{1 : 6{3 : 6{3 : 6{3 : 6{5 : 6{7 : 7{1 : 7{1 : 7{3 : 7{4 : 7{5 : 7{6 : 7{6 : 7{7 : 7{8 : 7{8 : 7{10 : 7{12 : 7{12 : 7{13 : 7{14 : 7{15 : 7{16 : 7{17 : 7{17 : 7{17 : 7{17 : 7{18 : 7{18 : 7{18 : 7{19 : 7{20 : 8{1 : 8{1 : 8{3 : 8{3 : 8{6
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
6{1
: : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : :
7{1
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
8{1
Victor Saouma
Draft 0{4
9 DESIGN PHILOSOPHIES and GUIDELINES
9.1 Safety Provisions : : : : : : : : : : : 9.2 Working Stress Method : : : : : : : 9.3 Ultimate Strength Method : : : : : : 9.3.1 y Probabilistic Preliminaries : 9.3.2 Discussion : : : : : : : : : : : 9.4 Example : : : : : : : : : : : : : : : : E 9-18 LRFD vs ASD : : : : : : : : 9.5 Design Guidelines : : : : : : : : : : :
CONTENTS
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 9{1 : 9{2 : 9{3 : 9{3 : 9{5 : 9{7 : 9{7 : 9{7
9{1
10.1 Nominal Strength : : : : : : : : : : : : : : : : : : 10.2 Failure Modes and Classi cation of Steel Beams : 10.3 Compact Sections : : : : : : : : : : : : : : : : : : 10.3.1 Bending Capacity of Beams : : : : : : : : 10.3.2 Design of Compact Sections : : : : : : : : 10.4 Partially Compact Section : : : : : : : : : : : : : 10.5 Slender Section : : : : : : : : : : : : : : : : : : : 10.6 Examples : : : : : : : : : : : : : : : : : : : : : : E 10-19Z for Rectangular Section : : : : : : : : : E 10-20Beam Design : : : : : : : : : : : : : : : :
10{1
: 10{2 : 10{2 : 10{4 : 10{4 : 10{6 : 10{6 : 10{7 : 10{7 : 10{7 : 10{8 : 11{1 : 11{1 : 11{2 : 11{2 : 11{3 : 11{3 : 11{4 : 11{4 : 11{5 : 11{6 : 11{7 : 11{8 : 11{9 : 11{9 : 11{10 : 11{10 : 12{1 : 12{1 : 12{4 : 12{4 : 12{4 : 12{4 : 12{4 : 12{5 : 12{8 : 12{10
11.1 Introduction : : : : : : : : : : : : : : : : : : : : : : : 11.1.1 Notation : : : : : : : : : : : : : : : : : : : : : 11.1.2 Modes of Failure : : : : : : : : : : : : : : : : 11.1.3 Analysis vs Design : : : : : : : : : : : : : : : 11.1.4 Basic Relations and Assumptions : : : : : : : 11.1.5 ACI Code : : : : : : : : : : : : : : : : : : : : 11.2 Cracked Section, Ultimate Strength Design Method : 11.2.1 Equivalent Stress Block : : : : : : : : : : : : 11.2.2 Balanced Steel Ratio : : : : : : : : : : : : : : 11.2.3 Analysis : : : : : : : : : : : : : : : : : : : : : 11.2.4 Design : : : : : : : : : : : : : : : : : : : : : : E 11-21Ultimate Strength Capacity : : : : : : : : : : E 11-22Beam Design I : : : : : : : : : : : : : : : : : E 11-23Beam Design II : : : : : : : : : : : : : : : : : 11.3 Continuous Beams : : : : : : : : : : : : : : : : : : : 11.4 ACI Code : : : : : : : : : : : : : : : : : : : : : : : : 12.1 Introduction : : : : : : : : : : : : : : 12.1.1 Materials : : : : : : : : : : : 12.1.2 Prestressing Forces : : : : : : 12.1.3 Assumptions : : : : : : : : : 12.1.4 Tendon Con guration : : : : 12.1.5 Equivalent Load : : : : : : : 12.1.6 Load Deformation : : : : : : 12.2 Flexural Stresses : : : : : : : : : : : E 12-24Prestressed Concrete I Beam 12.3 Case Study: Walnut Lane Bridge : :
11{1
12 PRESTRESSED CONCRETE
: : : : : : : : : :
: : : : : : : : : :
: : : : : : : : : :
: : : : : : : : : :
: : : : : : : : : :
: : : : : : : : : :
: : : : : : : : : :
: : : : : : : : : :
: : : : : : : : : :
12{1
Victor Saouma
Draft CONTENTS
12.3.1 12.3.2 12.3.3 12.3.4 Cross-Section Properties : Prestressing : : : : : : : : Loads : : : : : : : : : : : Flexural Stresses : : : : :
0{5
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 12{10 : 12{12 : 12{13 : 12{13
13 Three-Hinges ARCHES
13.1 Theory : : : : : : : : : : : : : : : : : : : : : : 13.1.1 Uniform Horizontal Load : : : : : : : E 13-25Design of a Three Hinged Arch : : : : 13.2 Case Study: Salginatobel Bridge (Maillart) : 13.2.1 Geometry : : : : : : : : : : : : : : : : 13.2.2 Loads : : : : : : : : : : : : : : : : : : 13.2.3 Reactions : : : : : : : : : : : : : : : : 13.2.4 Internal Forces : : : : : : : : : : : : : 13.2.5 Internal Stresses : : : : : : : : : : : : 13.3 Structural Behavior of Deck-Sti ened Arches
13{1
: 13{1 : 13{1 : 13{3 : 13{5 : 13{5 : 13{8 : 13{8 : 13{11 : 13{12 : 13{13 : 14{1 : 14{1 : 14{1 : 14{2 : 14{5 : 14{5 : 14{5 : 14{7 : 14{8 : 14{9 : 14{10 : 14{10 : 14{11 : 14{13 : 14{14 : 14{15 : 14{27 : 14{27 : 14{28 : 14{28 : 14{29 : 14{30 : 14{32 : 14{34
14 BUILDING STRUCTURES
14.1 Introduction : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.1.1 Beam Column Connections : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.1.2 Behavior of Simple Frames : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.1.3 Eccentricity of Applied Loads : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.2 Buildings Structures : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.2.1 Wall Subsystems : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.2.1.1 Example: Concrete Shear Wall : : : : : : : : : : : : : : : : : : : : : 14.2.1.2 Example: Trussed Shear Wall : : : : : : : : : : : : : : : : : : : : : 14.2.2 Shaft Systems : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.2.2.1 Example: Tube Subsystem : : : : : : : : : : : : : : : : : : : : : : : 14.2.3 Rigid Frames : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.3 Approximate Analysis of Buildings : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.3.1 Vertical Loads : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.3.2 Horizontal Loads : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.3.2.1 Portal Method : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : E 14-26Approximate Analysis of a Frame subjected to Vertical and Horizontal Loads 14.4 Lateral De ections : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.4.1 Short Wall : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.4.2 Tall Wall : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.4.3 Walls and Lintel : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.4.4 Frames : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.4.5 Trussed Frame : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14.4.6 Example of Transverse De ection : : : : : : : : : : : : : : : : : : : : : : : : : 14.4.7 E ect of Bracing Trusses : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
14{1
Victor Saouma
Draft
List of Figures
1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 2.14 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 4.1 4.2 4.3 4.4 4.5 Types of Forces in Structural Elements (1D) : Basic Aspects of Cable Systems : : : : : : : : Basic Aspects of Arches : : : : : : : : : : : : Types of Trusses : : : : : : : : : : : : : : : : Variations in Post and Beams Con gurations Di erent Beam Types : : : : : : : : : : : : : Basic Forms of Frames : : : : : : : : : : : : : Examples of Air Supported Structures : : : : Basic Forms of Shells : : : : : : : : : : : : : :
: : : : : : : : :
: : : : : : : : :
: : : : : : : : :
Approximation of a Series of Closely Spaced Loads Snow Map of the United States, ubc : : : : : : : : Loads on Projected Dimensions : : : : : : : : : : : Wind Map of the United States, (UBC 1995) : : : E ect of Wind Load on Structures(Schueller 1996) Approximate Design Wind Pressure p for Ordinary Wind Force Resisting Building Structures : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2{10 Vibrations of a Building : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2{12 Seismic Zones of the United States, (UBC 1995) : : : : : : : : : : : : : : : : : : : : : : : 2{13 Earth and Hydrostatic Loads on Structures : : : : : : : : : : : : : : : : : : : : : : : : : : 2{18 Load Placement to Maximize Moments : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2{21 Load Transfer in R/C Buildings : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2{22 Two Way Actions : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2{23 Load Life of a Structure, (Lin and Stotesbury 1981) : : : : : : : : : : : : : : : : : : : : : 2{24 Concept of Tributary Areas for Structual Member Loading : : : : : : : : : : : : : : : : : 2{25 Stress Strain Curves of Concrete and Steel : : : : : : : : : : : : : : : : : : : : : Standard Rolled Sections : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Residual Stresses in Rolled Sections : : : : : : : : : : : : : : : : : : : : : : : : Residual Stresses in Welded Sections : : : : : : : : : : : : : : : : : : : : : : : : In uence of Residual Stress on Average Stress-Strain Curve of a Rolled Section Concrete microcracking : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : W and C sections : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : prefabricated Steel Joists : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Ei Ei Ei Ei Ei el Tower (Billington and Mark 1983) : : : : : : : : : : : : : : : el Tower Idealization, (Billington and Mark 1983) : : : : : : : : el Tower, Dead Load Idealization (Billington and Mark 1983) : el Tower, Wind Load Idealization (Billington and Mark 1983) : el Tower, Wind Loads, (Billington and Mark 1983) : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: : : : : : : : : : : : : :
: 1{4 : 1{5 : 1{6 : 1{7 : 1{8 : 1{9 : 1{10 : 1{11 : 1{12 : 2{2 : 2{5 : 2{6 : 2{7 : 2{8
: : : : : : : : : : : : :
: : : : : : : : : : : : :
: : : : : : : : : : : : :
: : : : : : : : : : : : :
: : : : : : : : : : : : :
: 3{2 : 3{2 : 3{4 : 3{4 : 3{5 : 3{7 : 3{8 : 3{17 : 4{1 : 4{3 : 4{4 : 4{5 : 4{5
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
Draft 0{2
4.6 4.7 4.8 4.9 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14 5.15 5.16 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11 7.12 7.13 7.14 7.15 7.16 7.17 Ei Ei Ei Ei el Tower, Reactions (Billington and Mark 1983) : : : : : : : : el Tower, Internal Gravity Forces (Billington and Mark 1983) : el Tower, Horizontal Reactions (Billington and Mark 1983) : : el Tower, Internal Wind Forces (Billington and Mark 1983) : :
LIST OF FIGURES
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 4{5 : 4{6 : 4{7 : 4{8 : 5{2 : 5{3 : 5{4 : 5{4 : 5{9 : 5{10 : 5{11 : 5{11 : 5{14 : 5{15 : 5{15 : 5{17 : 5{17 : 5{38 : 5{43 : 5{44 : 6{1 : 6{4 : 6{5 : 6{6 : 6{7 : 6{7 : 6{8 : 6{9 : 6{9 : 7{2 : 7{3 : 7{3 : 7{4 : 7{5 : 7{7 : 7{9 : 7{9 : 7{10 : 7{11 : 7{11 : 7{12 : 7{13 : 7{14 : 7{15 : 7{16 : 7{19
Types of Supports : : : : : : : : : : : : : : : : : : : : : : : : : : : Inclined Roller Support : : : : : : : : : : : : : : : : : : : : : : : : Examples of Static Determinate and Indeterminate Structures : : : Geometric Instability Caused by Concurrent Reactions : : : : : : : Bridge Truss : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : A Statically Indeterminate Truss : : : : : : : : : : : : : : : : : : : X and Y Components of Truss Forces : : : : : : : : : : : : : : : : Sign Convention for Truss Element Forces : : : : : : : : : : : : : : Shear and Moment Sign Conventions for Design : : : : : : : : : : : Sign Conventions for 3D Frame Elements : : : : : : : : : : : : : : Free Body Diagram of an In nitesimal Beam Segment : : : : : : : Shear and Moment Forces at Di erent Sections of a Loaded Beam Slope Relations Between Load Intensity and Shear, or Between Shear and Moment Deformation of a Beam un Pure Bending : : : : : : : : : : : : : : : : : : : : : : : Elastic Curve from the Moment Diagram : : : : : : : : : : : : : : : : : : : : : : : Approximate Analysis of Beams : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Cable Structure Subjected to p(x) : : : : : : : : : : : : : : : : : : Longitudinal and Plan Elevation of the George Washington Bridge Truck Load : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Dead and Live Loads : : : : : : : : : : : : : : : : : : : : : : : : : : Location of Cable Reactions : : : : : : : : : : : : : : : : : : : : : : Vertical Reactions in Columns Due to Central Span Load : : : : : Cable Reactions in Side Span : : : : : : : : : : : : : : : : : : : : : Cable Stresses : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Deck Idealization, Shear and Moment Diagrams : : : : : : : : : : : Hamurrabi's Code : : : : : : : : : : : : : : : : : : : : : : : : Archimed : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Pantheon : : : : : : : : : : : : : : : : : : : : : : : : : : : : : From Vitruvius Ten Books on Architecture, (Vitruvius 1960) Hagia Sophia : : : : : : : : : : : : : : : : : : : : : : : : : : : Florence's Cathedral Dome : : : : : : : : : : : : : : : : : : : Palladio's Villa Rotunda : : : : : : : : : : : : : : : : : : : : : Stevin : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Galileo : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Discourses Concerning Two New Sciences, Cover Page : : : : \Galileo's Beam" : : : : : : : : : : : : : : : : : : : : : : : : : Experimental Set Up Used by Hooke : : : : : : : : : : : : : : Isaac Newton : : : : : : : : : : : : : : : : : : : : : : : : : : : Philosophiae Naturalis Principia Mathematica, Cover Page : Leonhard Euler : : : : : : : : : : : : : : : : : : : : : : : : : : Coulomb : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Nervi's Palazetto Dello Sport : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : :
8.1 Magazzini Generali Overall Dimensions, (Billington and Mark 1983) : : : : : : : : : : : : 8{2 8.2 Magazzini Generali Support System, (Billington and Mark 1983) : : : : : : : : : : : : : : 8{2
Victor Saouma
0{3
Magazzini Generali Loads (Billington and Mark 1983) : : : : : : : : : : : : : : : : : : : : 8{3 Magazzini Generali Beam Reactions, (Billington and Mark 1983) : : : : : : : : : : : : : : 8{3 Magazzini Generali Shear and Moment Diagrams (Billington and Mark 1983) : : : : : : : 8{4 Magazzini Generali Internal Moment, (Billington and Mark 1983) : : : : : : : : : : : : : 8{4 Magazzini Generali Similarities Between The Frame Shape and its Moment Diagram, (Billington and Mark 1983) : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 8{5 8.8 Magazzini Generali Equilibrium of Forces at the Beam Support, (Billington and Mark 1983) : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 8{5 8.9 Magazzini Generali E ect of Lateral Supports, (Billington and Mark 1983) : : : : : : : : 8{6 9.1 Load Life of a Structure : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 9{2 9.2 Frequency Distributions of Load Q and Resistance R : : : : : : : : : : : : : : : : : : : : : 9{4 9.3 De nition of Reliability Index : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 9{4 10.1 10.2 10.3 10.4 10.5 10.6 10.7 11.1 11.2 11.3 11.4 11.5 12.1 12.2 12.3 12.4 12.5 12.6 Lateral Bracing for Steel Beams : : : : : : : : : : : : : : : : : : : Failure of Steel beam Plastic Hinges : : : : : : : : : : : : : : : : Failure of Steel beam Local Buckling : : : : : : : : : : : : : : : Failure of Steel beam Lateral Torsional Buckling : : : : : : : : : Stress distribution at di erent stages of loading : : : : : : : : : : Stress-strain diagram for most structural steels : : : : : : : : : : Nominal Moments for Compact and Partially Compact Sections : Failure Modes for R/C Beams : : : : : : : Internal Equilibrium in a R/C Beam : : : Cracked Section, Limit State : : : : : : : Whitney Stress Block : : : : : : : : : : : Reinforcement in Continuous R/C Beams
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: : : : : : : : : : : :
: 10{1 : 10{3 : 10{3 : 10{4 : 10{4 : 10{5 : 10{7 : 11{2 : 11{3 : 11{4 : 11{5 : 11{11
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
: : : : :
Pretensioned Prestressed Concrete Beam, (Nilson 1978) : : : : : : : : : : : : : : : : : : : 12{2 Posttensioned Prestressed Concrete Beam, (Nilson 1978) : : : : : : : : : : : : : : : : : : : 12{2 7 Wire Prestressing Tendon : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 12{3 Alternative Schemes for Prestressing a Rectangular Concrete Beam, (Nilson 1978) : : : : 12{5 Determination of Equivalent Loads : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 12{6 Load-De ection Curve and Corresponding Internal Flexural Stresses for a Typical Prestressed Concrete Beam, (Nilson 1978) : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 12{6 12.7 Flexural Stress Distribution for a Beam with Variable Eccentricity Maximum Moment Section and Support Section, (Nilson 1978) : : : : : : : : : : : : : : : : : : : : : : : : : : 12{7 12.8 Walnut Lane Bridge, Plan View : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 12{11 12.9 Walnut Lane Bridge, Cross Section : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 12{12
13.1 Moment Resisting Forces in an Arch or Suspension System as Compared to a Beam, (Lin and Stotesbury 1981) : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 13{2 13.2 Statics of a Three-Hinged Arch, (Lin and Stotesbury 1981) : : : : : : : : : : : : : : : : : 13{2 13.3 Two Hinged Arch, (Lin and Stotesbury 1981) : : : : : : : : : : : : : : : : : : : : : : : : : 13{3 13.4 Arch Rib Sti ened with Girder or Truss, (Lin and Stotesbury 1981) : : : : : : : : : : : : 13{3 13.5 Salginatobel Bridge Dimensions, (Billington and Mark 1983) : : : : : : : : : : : : : : : : 13{5 13.6 Salginatobel Bridge Idealization, (Billington and Mark 1983) : : : : : : : : : : : : : : : : 13{6 13.7 Salginatobel Bridge Hinges, (Billington and Mark 1983) : : : : : : : : : : : : : : : : : : : 13{6 13.8 Salginatobel Bridge Sections, (Billington and Mark 1983) : : : : : : : : : : : : : : : : : : 13{7 13.9 Salginatobel Bridge Dead Load, (Billington and Mark 1983) : : : : : : : : : : : : : : : : 13{8 13.10Salginatobel Bridge Truck Load, (Billington and Mark 1983) : : : : : : : : : : : : : : : : 13{9 13.11Salginatobel Bridge Total Vertical Load, (Billington and Mark 1983) : : : : : : : : : : : : 13{10
Victor Saouma
Draft 0{4
LIST OF FIGURES
: : : : : : : : : : : : : : : : : : : : : 13{10 : 13{11 : 13{12 : 13{14 : 14{1
13.12Salginatobel Bridge Reactions, (Billington and Mark 1983) : : : : : : : : : : : 13.13Salganitobel Bridge Shear Diagrams, (Billington and Mark 1983) : : : : : : : : 13.14Salginatobel Bridge Live Load Moment Diagram, (Billington and Mark 1983) : 13.15Structural Behavior of Sti ened Arches, (Billington 1979) : : : : : : : : : : : :
14.2 Deformation of Flexible and Rigid Frames Subjected to Vertical and Horizontal Loads, (Lin and Stotesbury 1981) : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14{2 14.3 Deformation, Shear, Moment, and Axial Diagrams for Various Types of Portal Frames Subjected to Vertical and Horizontal Loads : : : : : : : : : : : : : : : : : : : : : : : : : : 14{3 14.4 Axial and Flexural Stresses : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14{4 14.5 Design of a Shear Wall Subsystem, (Lin and Stotesbury 1981) : : : : : : : : : : : : : : : : 14{6 14.6 Trussed Shear Wall : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14{8 14.7 Design Example of a Tubular Structure, (Lin and Stotesbury 1981) : : : : : : : : : : : : : 14{9 14.8 A Basic Portal Frame, (Lin and Stotesbury 1981) : : : : : : : : : : : : : : : : : : : : : : : 14{10 14.9 Approximate Analysis of Frames Subjected to Vertical Loads Girder Moments : : : : : : 14{12 14.10Approximate Analysis of Frames Subjected to Vertical Loads Column Axial Forces : : : : 14{12 14.11Approximate Analysis of Frames Subjected to Vertical Loads Column Moments : : : : : 14{13 14.12Approximate Analysis of Frames Subjected to Lateral Loads Column Shear : : : : : : : : 14{14 14.13***Approximate Analysis of Frames Subjected to Lateral Loads Girder Moment : : : : : 14{15 14.14Approximate Analysis of Frames Subjected to Lateral Loads Column Axial Force : : : : 14{15 14.15Example Approximate Analysis of a Building : : : : : : : : : : : : : : : : : : : : : : : : : 14{16 14.16Approximate Analysis of a Building Moments Due to Vertical Loads : : : : : : : : : : : : 14{17 14.17Approximate Analysis of a Building Shears Due to Vertical Loads : : : : : : : : : : : : : 14{18 14.18Approximate Analysis for Vertical Loads Spread-Sheet Format : : : : : : : : : : : : : : : 14{20 14.19Approximate Analysis for Vertical Loads Equations in Spread-Sheet : : : : : : : : : : : : 14{21 14.20Approximate Analysis of a Building Moments Due to Lateral Loads : : : : : : : : : : : : 14{23 14.21Portal Method Spread-Sheet Format : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14{24 14.22Portal Method Equations in Spread-Sheet : : : : : : : : : : : : : : : : : : : : : : : : : : : 14{25 14.23Shear Deformation in a Short Building, (Lin and Stotesbury 1981) : : : : : : : : : : : : : 14{28 14.24Flexural Deformation in a Tall Building, (Lin and Stotesbury 1981) : : : : : : : : : : : : 14{28 14.25De ection in a Building Structure Composed of Two Slender Walls and Lintels, (Lin and Stotesbury 1981) : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 14{29 14.26Portal Method to Estimate Lateral Deformation in Frames, (Lin and Stotesbury 1981) : : 14{30 14.27Shear and Flexural De ection of a Rigid Frame Subsystem, (Lin and Stotesbury 1981) : : 14{31 14.28Side-Sway De ection from Unsymmetrical Vertical Load, (Lin and Stotesbury 1981) : : : 14{31 14.29Axial Elongation and Shortening of a Truss Frame, (Lin and Stotesbury 1981) : : : : : : 14{31 14.30Transverse De ection, (Lin and Stotesbury 1981) : : : : : : : : : : : : : : : : : : : : : : : 14{32 14.31Frame Rigidly Connected to Shaft, (Lin and Stotesbury 1981) : : : : : : : : : : : : : : : : 14{34 14.32E ect of Exterior Column Bracing in Buildings, (Lin and Stotesbury 1981) : : : : : : : : 14{35
Victor Saouma
Draft
List of Tables
1.1 Structural Engineering Coverage for Architects and Engineers : : : : : : : : : : : : : : : : 1{12 1.2 tab:secae : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 1{12 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 3.1 3.2 3.3 3.4 Unit Weight of Materials : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2{2 Weights of Building Materials : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2{3 Average Gross Dead Load in Buildings : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2{3 Minimum Uniformly Distributed Live Loads, (UBC 1995) : : : : : : : : : : : : : : : : : : 2{4 Wind Velocity Variation above Ground : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2{7 Ce Coe cients for Wind Load, (UBC 1995) : : : : : : : : : : : : : : : : : : : : : : : : : : 2{8 Wind Pressure Coe cients Cq , (UBC 1995) : : : : : : : : : : : : : : : : : : : : : : : : : : 2{8 Importance Factors for Wind and Earthquake Load, (UBC 1995) : : : : : : : : : : : : : : 2{9 Approximate Design Wind Pressure p for Ordinary Wind Force Resisting Building Structures : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2{10 Z Factors for Di erent Seismic Zones, ubc : : : : : : : : : : : : : : : : : : : : : : : : : : : 2{12 S Site Coe cients for Earthquake Loading, (UBC 1995) : : : : : : : : : : : : : : : : : : : 2{13 Partial List of RW for Various Structure Systems, (UBC 1995) : : : : : : : : : : : : : : : 2{15 Coe cients of Thermal Expansion : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2{19 Properties of Major Structural Steels : Properties of Reinforcing Bars : : : : : Joist Series Characteristics : : : : : : Joist Properties : : : : : : : : : : : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
: : : :
5.1 Equations of Equilibrium : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 5{3 5.2 Static Determinacy and Stability of Trusses : : : : : : : : : : : : : : : : : : : : : : : : : : 5{10 5.3 Section Properties : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 5{41 9.1 9.2 9.3 9.4 Allowable Stresses for Steel and Concrete : : : : : : : : : : : : : : : : : : : : : : : : : : : 9{3 Selected values for Steel and Concrete Structures : : : : : : : : : : : : : : : : : : : : : : 9{5 Strength Reduction Factors, : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 9{6 Approximate Structural Span-Depth Ratios for Horizontal Subsystems and Components (Lin and Stotesbury 1981) : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 9{8
14.1 Columns Combined Approximate Vertical and Horizontal Loads : : : : : : : : : : : : : : 14{26 14.2 Girders Combined Approximate Vertical and Horizontal Loads : : : : : : : : : : : : : : : 14{27
Draft 0{2
LIST OF TABLES
Victor Saouma
Draft
Chapter 1
INTRODUCTION
1.1 Science and Technology
1
\There is a fundamental di erence between science and and technology. Engineering or technology is the making of things that did not previously exist, whereas science is the discovering of things that have long existed. Technological results are forms that exist only because people want to make them, whereas scienti c results are informations of what exists independently of human intentions. Technology deals with the arti cial, science with the natural." (Billington 1985)
Structural design is a ected by various environmental constraints: 1. Major movements: For example, elevator shafts are usually shear walls good at resisting lateral load (wind, earthquake). 2. Sound and structure interact: A dome roof will concentrate the sound A dish roof will di use the sound 3. Natural light: A at roof in a building may not provide adequate light.
Draft 1{2
INTRODUCTION
A Folded plate will provide adequate lighting (analysis more complex). A bearing and shear wall building may not have enough openings for daylight. A Frame design will allow more light in (analysis more complex). 4. Conduits for cables (electric, telephone, computer), HVAC ducts, may dictate type of oor system. 5. Net clearance between columns (unobstructed surface) will dictate type of framing.
Architecture must be the product of a creative collaboration of architects and engineers. 5 Architect stress the overall, rather than elemental approach to design. In the design process, they conceptualize a space-form scheme as a total system. They are generalists. 6 The engineer, partly due to his/her education think in reverse, starting with details and without su cient regards for the overall picture. (S)he is a pragmatist who \knows everything about nothing". 7 Thus there is a conceptual gap between architects and engineers at all levels of design. 8 Engineer's education is more specialized and in depth than the architect's. However, engineer must be kept aware of overall architectural objective. 9 In the last resort, it is the architect who is the leader of the construction team, and the engineers are his/her servant. 10 A possible compromise might be an Architectural Engineer.
Architectural design is hierarchical: Schematic: conceptual overall space-form feasibility of basic schematic options. Collaboration is mostly between the owner and the architect. Preliminary: Establish basic physical properties of major subsystems and key components to prove design feasibility. Some collaboration with engineers is necessary. Final design: nal in-depth design re nements of all subsystems and components and preparation of working documents (\blue-prints"). Engineers play a leading role.
Victor Saouma
1{3
Buildings may have di erent functions: Residential: housing, which includes low-rise (up tp 2-3 oors), mid-rise (up to 6-8 oors) and high rise buildings. Commercial: O ces, retail stores, shopping centers, hotels, restaurants. Industrial: warehouses, manufacturing. Institutional: Schools, hospitals, prisons, chruch, government buildings. Special: Towers, stadium, parking, airport, etc.
Given an existing structure subjected to a certain load determine internal forces (axial, shear, exural, torsional or stresses), de ections, and verify that no unstable failure can occur. 15 Thus the basic structural requirements are: Strength: stresses should not exceed critical values: < f Sti ness: de ections should be controlled: < max Stability: buckling or cracking should also be prevented
Given a set of forces, dimension the structural element. Steel/wood Structures Select appropriate section. Reinforced Concrete: Determine dimensions of the element and internal reinforcement (number and sizes of reinforcing bars).
17 For new structures, iterative process between analysis and design. A preliminary design is made using rules of thumbs (best known to Engineers with design experience) and analyzed. Following design, we check for Serviceability: de ections, crack widths under the applied load. Compare with acceptable values speci ed in the design code. Failure (limit state): and compare the failure load with the applied load times the appropriate factors of safety. If the design is found not to be acceptable, then it must be modi ed and reanalyzed. 18 For existing structures rehabilitation, or veri cation of an old infrastructure, analysis is the most important component. 19 In summary, analysis is always required.
Victor Saouma
Draft 1{4
INTRODUCTION
From Strength of Materials, loads can be transferred through various mechanisms, Fig. 1.1 Axial: cables, truss elements, arches, membrane, shells Flexural: Beams, frames, grids, plates Torsional: Grids, 3D frames Shear: Frames, grids, shear walls.
Tension & Compression Structures: only, no shear, exure, or torsion. Those are the most e cient types of structures. Cable (tension only): The high strength of steel cables, combined with the e ciency of simple
tension, makes cables ideal structural elements to span large distances such as bridges, and dish roofs, Fig. 1.2. A cable structure develops its load carrying capacity by adjusting its shape so as to provide maximum resistance (form follows function). Care should be exercised in minimizing large de ections and vibrations. Arches (mostly compression) is a \reversed cable structure". In an arch, exure/shear is minimized and most of the load is transfered through axial forces only. Arches are used for large span roofs and bridges, Fig. 1.3
Victor Saouma
1{5
Victor Saouma
Draft 1{6
INTRODUCTION
Victor Saouma
1{7
Trusses have pin connected elements which can transmit axial forces only (tension and compression). Elements are connected by either slotted, screwed, or gusset plate connectors. However, due to construction details, there may be secondary stresses caused by relatively
Whereas r/c beams are mostly rectangular or T shaped, steel beams are usually I shaped (if the top anges are not properly sti ened, they may buckle, thus we must have sti eners). Frames: Load is co-planar with the structure. Axial, shear, exure (with respect to one axis in 2D structures and with respect to two axis in 3D structures), torsion (only in 3D). The frame is composed of at least one horizontal member (beam) rigidly connected to vertical ones1. The vertical The precursor of the frame structures were the Post and Lintel where the post is vertical member on which the lintel
is simply posed.
1
Post and Beams: Essentially a support column on which a \beam" rests, Fig. 1.5, and 1.6. Beams: Shear, exure and sometimes axial forces. Recall that = Mc I is applicable only for shallow beams, i.e. span/depth at least equal to ve.
Victor Saouma
Draft 1{8
INTRODUCTION
Victor Saouma
1{9
BRACED BEAM
CABLE-STAYED BEAM
BOWSTRING TRUSS
GABLED TRUSS
Victor Saouma
Draft 1{10
INTRODUCTION
members can have di erent boundary conditions (which are usually governed by soil conditions). Frames are extensively used for houses and buildings, Fig. 1.7.
Grids and Plates: Load is orthogonal to the plane of the structure. Flexure, shear, torsion.
In a grid, beams are at right angles resulting in a two-way dispersal of loads. Because of the rigid connections between the beams, additional sti ness is introduced by the torsional resistance of members. Grids can also be skewed to achieve greater e ciency if the aspect ratio is not close to one. Plates are at, rigid, two dimensional structures which transmit vertical load to their supports. Used mostly for oor slabs. Folded plates is a combination of transverse and longitudinal beam action. Used for long span roofs. Note that the plate may be folded circularly rather than longitudinally. Folded plates are used mostly as long span roofs. However, they can also be used as vertical walls to support both vertical and horizontal loads. Membranes: 3D structures composed of a exible 2D surface resisting tension only. They are usually cable-supported and are used for tents and long span roofs Fig. 1.8.
Victor Saouma
1{11
Victor Saouma
Draft 1{12
axial stresses only, Fig. 1.9.
INTRODUCTION
Shells: 3D structures composed of a curved 2D surface, they are usually shaped to transmit compressive
Figure 1.9: Basic Forms of Shells Shells are classi ed in terms of their curvature.
Structural engineering education can be approached from either one of two points of views, depending on the audience, ??. Architects Global Structure Approximate, \rules of thumbs" preliminary Structures Most Design Approximate Approach Emphasis Analysis Engineers Elemental Component Exact, detailled Final Trusses, Frames Per code
Table 1.1: Structural Engineering Coverage for Architects and Engineers Table 1.2: tab:secae
Victor Saouma
1{13
Architects: Start from overall design, and move toward detailed analysis. Emphasis on good understanding of overall structural behavior. Develop a good understanding of load transfer mechanism for most types of structures, cables, arches, beams, frames, shells, plates. Approximate analysis for most of them. Engineers: Emphasis is on the individual structural elements and not always on the total system. Focus on beams, frames (mostly 2D) and trusses. Very seldom are arches covered. Plates and shells are not even mentioned.
1.12 References
23
Following are some useful references for structural engineering, those marked by y were consulted, and \borrowed from" in preparing the Lecture Notes or are particularly recommended.
Structures for Engineers 1. y Arbadi, F. Structural Analysis and Behavior, McGraw-Hill, Inc., 1991. Victor Saouma
1. Ambrose, J., Building Structures, second Ed. Wiley, 1993. 2. Billington, D.P. Rober Maillart's Bridges The Art of Engineering, Princeton University Pres, 1979. 3. yBillington, D.P., The Tower and the Bridge The new art of structural engineering, Princeton University Pres,, 1983. 4. yBillington, D.P., Structures and the Urban Environment, Lectures Notes CE 262, Department of Civil Engineering, Princeton University, 1978 5. French, S., Determinate Structures Statics, Strength, Analysis, Design, Delmar, 1996. 6. Gordon, J.E., Structures, or Why Things Do'nt Fall Down, Da Capo paperback, New York, 1978. 7. Gordon, J.E., The Science of Structures and Materials, Scienti c American Library, 1988. 8. Hawkes, N., Structures, the way things are built, MacMillan, 1990. 9. Levy, M. and Salvadori, M., Why Buildings Fall Down, W.W.Norton, 1992. 10. yLin, T.Y. and Stotesbury, S.D., Structural Concepts and Systems for Architects and Engineers, John Wiley, 1981. 11. yMainstone, R., Developments in Structural Form, Allen Lane Publishers, 1975. 12. Petroski, H., To Enginer is Human, Vintage Books, 1992. 13. ySalvadori, M. and Heller, R., Structure in Architecture The Building of Buildings, Prentice Hall, Third Edition, 1986. 14. Salvadori, M. and Levy, M., Structural Design in Architecture, Prentice hall, Second Edition, 1981. 15. Salvadori, M., Why Buildings Stand Up The Strength of Architecture, Norton Paperack, 1990. 16. ySandaker, B.N. and Eggen, A.P., The Structural Basis of Architecture, Whitney Library of Design, 1992. 17. ySchueller, W., The design of Building Structures, Prentice Hall, 1996.
2. Biggs, J.M., Introduction to Structural Engineering Analysis and Design, Prentice Hall, 1986.
Draft 1{14
INTRODUCTION
Codes
3. Hsieh, Y.Y., Elementary Theory of Structures, Third Edition, Prentice Hall, 1988. 4. Ghali, A., and Neville, A.M., Structural Analysis, Third Edition, Chapman and Hall, 1989 5. White, R. Gergely, P. and Sexmith, R., Structural Engineering Combined Edition, John Wiley, 1976. 6. y Nilson, A., and Winter, G. Design of Concrete Structures, Eleventh Edition, McGraw Hill, 1991. 7. Galambos, T., Lin, F.J., and Johnston, B.G., Basic Steel Design with LRFD, Prentice Hall, 1996. 8. y Salmon C. and Johnson, J. Steel Structures, Third Edition, Harper Collins Publisher, 1990. 9. y Gaylord, E.H., Gaylord, C.N. and Stallmeyer, J.E., Design of Steel Structures, Third Edition, McGraw Hill, 1992. 10. Vitruvius, The Ten Books on Architecture, Dover Publications, 1960. 11. Palladio, A., The Four Books of Architecture, Dover Publication. 1. ACI-318-89, Building Code Requirements for Reinforced Concrete, American Concrete Institute 2. Load & Resistance Factor Design, Manual of Steel Construction, American Institute of Steel Construction. 3. Uniform Building Code, International Conference of Building O cials, 5360 South Workman Road Whittier, CA 90601 4. Minimum Design Loads in Buildings and Other Structures, ANSI A58.1, American National Standards Institute, Inc., New York, 1972.
Victor Saouma
Draft
Chapter 2
LOADS
2.1 Introduction
1
The main purpose of a structure is to transfer load from one point to another: bridge deck to pier slab to beam beam to girder girder to column column to foundation foundation to soil. 2 There can also be secondary loads such as thermal (in restrained structures), di erential settlement of foundations, P-Delta e ects (additional moment caused by the product of the vertical force and the lateral displacement caused by lateral load in a high rise building). 3 Loads are generally subdivided into two categories Vertical Loads or gravity load 1. dead load (DL) 2. live load (LL) also included are snow loads. Lateral Loads which act horizontally on the structure 1. Wind load (WL) 2. Earthquake load (EL) this also includes hydrostatic and earth loads.
4 This distinction is helpful not only to compute a structure's load, but also to assign di erent factor of safety to each one. 5 For a detailed coverage of loads, refer to the Universal Building Code (UBC), (UBC 1995).
For closely spaced identical loads (such as joist loads), it is customary to treat them as a uniformly distributed load rather than as discrete loads, Fig. 2.1
Draft 2{2
P1 P2 P3 P4
LOADS
P5 P6 P7
SUPPORT BEAM
SPAN
Dead loads (DL) consist of the weight of the structure itself, and other permanent xtures (such as walls, slabs, machinery). 8 For analysis purposes, dead loads can easily be determined from the structure's dimensions and density, Table 2.1
Material
lb=ft3 Aluminum 173 Brick 120 Concrete 145 Steel 490 Wood (pine) 40
For steel structures, the weight per unit length of rolled sections is given in the AISC Manual of Steel Construction. 10 For design purposes, dead loads must be estimated and veri ed at the end of the design cycle. This makes the design process iterative. 11 Weights for building materials is given in Table 2.2 12 For preliminary design purposes the average dead loads of Table 2.3 can be used:
Contrarily to dead loads which are xed and vertical, live loads (LL) are movable or moving and may be horizontal. 14 Occupancy load may be due to people, furniture, equipment. The loads are essentially variable point loads which can be placed anywhere.
Victor Saouma
2{3
Material
lb=ft2 Timber 40-50 Steel 50-80 Reinforced concrete 100-150 Table 2.3: Average Gross Dead Load in Buildings
Victor Saouma
Draft 2{4
15
LOADS
In analysis load placement should be such that their e ect (shear/moment) are maximized. 16 A statistical approach is used to determine a uniformly distributed static load which is equivalent to the weight of the maximum concentration of occupants. These loads are de ned in codes such as the Uniform Building Code or the ANSI Code, Table 2.4.
Use or Occupancy
lb=ft2 Assembly areas 50 Cornices, marquees, residential balconies 60 Corridors, stairs 100 Garage 50 O ce buildings 50 Residential 40 Storage 125-250 Table 2.4: Minimum Uniformly Distributed Live Loads, (UBC 1995)
17
For small areas (30 to 50 sq ft) the e ect of concentrated load should be considered separately. 18 Since there is a small probability that the whole oor in a building be fully loaded, the UBC code speci es that the occupancy load for members supporting an area A larger than 150 ft2 (i.e. a column with a total tributary area, including oors above it, larger than 150 ft2 ) may be reduced by R where
(2.1)
where r = :08 for oors, A is the supported area ( 2 ) DL and LL are the dead and live loads per unit area supported by the member. R can not exceed 40% for horizontal members and 60% for vertical ones.
Solution:
1. 2. 3. 4.
The tributary area is 16 16 = 256ft2 > 150 The reduction R for the roof is is R = :08(16 16 ; 150) = 8:48% ; 60 = 40:4% which is less than 60% p Maximum allowable reduction Rmax = 23:1 1 + 80 The reduced cumulative load for the column of each oor is
Floor A A ; 150 R0 R% LL (100 ; R) LL=100 Roof 10 256 512 106 362 8.48 28.96 8.48 28.96 20 80 18.3 56.83 9 768 618 49.44 40.4 80 47.68 8 7 1024 1280 874 1130 69.92 90.40 40.4 40.4 80 80 47.68 47.68 6 1536 1386 110.88 40.4 80 47.68 5 1792 1642 131.36 40.4 80 47.68 4 2048 1898 151.84 40.4 80 47.68 3 2304 2154 172.32 40.4 80 47.68 2 2560 2410 192.8 40.4 80 47.68
Victor Saouma
2{5
The resulting design live load for the bottom column has been reduced from 2 + (9)(80) (256) 2 = 189,440 LLBefore = (20) (256) } (2.2) | {z | {z } Roof 9 oors to 2 + (9)(47:68) (256) 2 = 114,540 LLReduced = (18 :3) {z(256) } (2.3) | {z } | Roof 9 oors 5. The total dead load is DL = (10)(60) (256) 2 (1 000) = 153:6 Kips, thus the total reduction ;268 100= 22% . in load is from 153:6+189:4 = 343 to 153:6+114:5 = 268:1 a reduction of 343 343
psf ft k lbs k k
2.2.3 Snow
19 Roof snow load vary greatly depending on geographic location and elevation. They range from 20 to 45 psf, Fig. 2.2.
Snow loads are always given on the projected length or area on a slope, Fig. 2.3. 21 The steeper the roof, the lower the snow retention. For snow loads greater than 20 psf and roof pitches more than 20 the snow load p may be reduced by
p ; 0:5 R = ( ; 20) 40
(psf)
(2.4)
Wind load depend on: velocity of the wind, shape of the building, height, geographical location, texture of the building surface and sti ness of the structure.
Victor Saouma
Draft 2{6
LIVE LOAD DEAD LOAD WIND LOAD
LOADS
Figure 2.3: Loads on Projected Dimensions Wind loads are particularly signi cant on tall buildings1. 24 When a steady streamline air ow of velocity V is completely stopped by a rigid body, the stagnation pressure (or velocity pressure) qs was derived by Bernouilli (1700-1782) 1 V2 qs = 2 (2.5) where the air mass density is the air weight divided by the accleration of gravity g = 32:2 ft/sec2 . At sea level and a temperature of 15oC (59oF), the ai weighs 0.0765 lb/ft3 this would yield a pressure of
23
LE N G TH
RUN
or
1 (0:0765)lb/ft qs = 2 (32:2)ft/sec2
(5280)ft/mile V (3600)sec/hr
RISE
(2.6) (2.7)
qs = 0:00256V 2
where V is the maximum wind velocity (in miles per hour) and qs is in psf. V can be obtained from wind maps (in the United States 70 V 110), Fig. 2.4. 25 During storms, wind velocities may reach values up to or greater than 150 miles per hour, which corresponds to a dynamic pressure qs of about 60 psf (as high as the average vertical occupancy load in buildings). The primary design consideration for very high rise buildings is the excessive drift caused by lateral load (wind and
possibly earthquakes).
1
Victor Saouma
2{7
Wind pressure increases with height, Table 2.5. Height Zone (in feet) <30 30 to 49 50 to 99 100 to 499 500 to 1199 >1,200 20 15 20 25 30 35 40 Wind-Velocity Map Area 25 30 35 40 45 50 20 25 25 30 35 40 25 30 35 40 45 50 30 40 45 50 55 60 40 45 55 60 70 75 45 55 60 70 80 90 50 60 70 80 90 100
Table 2.5: Wind Velocity Variation above Ground Wind load will cause suction on the leeward sides, Fig. 2.6 28 This magnitude must be modi ed to account for the shape and surroundings of the building. Thus, the design base pressure (at 33.3 ft from the ground) p (psf) is given by
27
p = Ce Cq Iqs
(2.8)
The pressure is assumed to be normal to all walls and roofs and Ce Velocity Pressure Coe cient accounts for height, exposure and gust factor. It accounts for the fact that wind velocity increases with height and that dynamic character of the air ow (i.e the wind pressure is not steady), Table 2.6. l Cq Pressure Coe cient is a shape factor which is given in Table 2.7 for gabled frames. I Importance Factor as given by Table 2.8. where
Victor Saouma
Draft 2{8
LOADS
Figure 2.5: E ect of Wind Load on Structures(Schueller 1996) Exposure D Open, at terrain facing large bodies of water C Flat open terrain, extending one-half mile or open from the site in any full quadrant 0.62-1.80 B Terrain with buildings, forest, or surface irregularities 20 ft or more in height 1.39-2.34 1.06-2.19 Table 2.6: Ce Coe cients for Wind Load, (UBC 1995) Windward Side Leeward Side Gabled Frames (V:H) Roof Slope <9:12 ;0:7 ;0:7 9:12 to 12:12 0:4 ;0:7 >12:12 0:7 ;0:7 Walls 0:8 ;0:5 Buildings (height < 200 ft) Vertical Projections height < 40 ft 1:3 ;1:3 height > 40 ft 1:4 ;1:4 Horizontal Projections ;0:7 ;0:7 Table 2.7: Wind Pressure Coe cients Cq , (UBC 1995)
Ce
Victor Saouma
Table 2.8: Importance Factors for Wind and Earthquake Load, (UBC 1995)
I Essential Facilities: Hospitals Fire and police stations Tanks Emergency vehicle shelters,
standby power-generating equipment Structures and equipment in government. communication centers. II Hazardous Facilities: Structures housing, supporting or containing su cient quantities of toxic or explosive substances to be dangerous to the safety of the general public if released. III Special occupancy structure: Covered structures whose primary occupancy is public assembly, capacity > 300 persons. Buildings for schools through secondary or day-care centers, capacity > 250 persons. Buildings for colleges or adult education schools, capacity > 500 persons. Medical facilities with 50 or more resident incapacitated patients, but not included above Jails and detention facilities All structures with occupancy >5,000 persons. Structures and equipment in power generating stations and other public utilitiy facilities not included above, and required for continued operation. IV Standard occupancy structure: All structures having occupancies or functions not listed above.
29
For the preliminary design of ordinary buildings Ce = 1:0 and Cq = 1:3 may be assumed, yielding
p = (1:3):020256V 2 = :00333V 2
which corresponds to a pressure of 21 psf for a wind speed of 80 mph, Fig. 2.6, Table 2.9.
(2.9)
Solution:
1. From Fig. 2.4 the maximum wind velocity is St. Louis is 70 mph, since the building is protected we can take Ce = 0:7, I = 1:. The base wind pressure is qs = 0:00256 (70)2 = 12:54 psf.
Victor Saouma
Draft 2{10
Height Above Grade (ft) 0-15 20 25 30 40 60 80 100 120 160 200 300 400
Table 2.9: Approximate Design Wind Pressure p for Ordinary Wind Force Resisting Building Structures
350
300
250
200
150
100
50
10
45
50
Figure 2.6: Approximate Design Wind Pressure p for Ordinary Wind Force Resisting Building Structures
Victor Saouma
2{11
2. The slope of the roof is 8:15=6.4:12 which gives Cq = ;0:7 for both the windward and leeward sides. The vertical walls have Cq = 0:8 for the winward side and Cq = ;0:5 for the leeward one. 3. Thus the applied pressure on the roof is p = 0:7 (;0:7) 12:54 = -6.14 psf that is the roof is subjected to uplift. 4. The winward wall, the pressure is 0:7 0:8 12:54 = 7.02 psf , and for the leeward wall 0:7 (;0:5) 12:54 = -4.39 psf (suction) , 5. The direction of the wind can change and hence each structural component must be designed to resist all possible load combinations. 6. For large structures which may be subjected to large wind loads, testing in a wind tunnel of the structure itself and its surroundings is often accomplished.
2.3.2 Earthquakes
Buildings should be able to resist Minor earthquakes without damage Moderate earthquakes without structural damage but possibly with some nonstructural damages Major earthquakes without collapse but possibly with some structural damage as well as nonstructural damage This is achieved through an appropriate dynamic analysis. 31 For preliminary designs or for small structures an equivalent horizontal static load can be determined. 32 Actual loads depend on the following 1. Intensity of the ground acceleration (including soil/rock properties). 2. Dynamic properties of the building, such as its mode shapes and periods of vibration and its damping characteristics. 3. Mass of the building.
30
Victor Saouma
Draft 2{12
LOADS
33 A critical factor in the dynamic response of a structure is the fundamental period of the structure's vibration (or rst mode of vibration). This is the time required for one full cycle of motion, Fig. 2.7. If the earthquake excitation has a frequency close to the one of the building, then resonance may occur. This should be avoided.
Figure 2.7: Vibrations of a Building Earthquake load manifests itself as a horizontal force due to the (primarily) horizontal inertia force (F = ma). 35 The horizontal force at each level is calculated as a portion of the base shear force V
34
V = ZIC RW W
where:
(2.10)
I : Importance Factor: which was given by Table 2.8. C : Design Response Spectrum given by
Victor Saouma
:25S C = 1T 2=3
2:75
(2.11)
2{13
T is the fundamental period of vibration of the building in seconds. This can be determined from T = Ct (hn )3=4
where: hn is the building height above base in ft. and
either the free vibration analysis of the building, or estimated from the following empirical formula (2.12)
steel moment resisting frames reinforced concrete moment resisting frames and eccentrically braced frames all other buildings cient given by Table 2.11 Note that most of the damages in the 1990? earthquake
Type Description S Factor S1 A soil pro le with either rock-like material or sti /dense soil less 1.0 than 200 ft. S2 Dense or sti soil exceeding 200 ft 1.2 S3 70 ft or more soil containing more than 20 ft of soft to medium sti 1.5 clay but not more than 40 ft. of soft clay. S4 Soil containing more than 40 ft of soft clay 2.0 Table 2.11: S Site Coe cients for Earthquake Loading, (UBC 1995) in San Francisco occurred in the marina where many houses were built on soft soil. and
C RW
0:075
(2.13)
Victor Saouma
Draft 2{14
RW is given by Table 2.12. W Load total structure load.
36
LOADS
The horizontal force V is distributed over the height of the building in two parts. The rst (applied only if T 0:7 sec.) is a concentrated force F1 equal to
Ft = 0:07TV
0:25V
(2.14)
is applied at the top of the building due to whiplash. The balance of the force V ; Ft is distributed as a triangular load diminishing to zero at the base. 37 Assuming a oor weight constant for every oor level, then the force acting on each one is given by (V ; Ft )hx = (V ; Ft )hx (2.15) Fx = h + n hi 1 h2 + + hn i=1 where hi and hx are the height in ft above the base to level i, or x respectively. Note that it is assumed that all oors have also same width.
Solution:
1. The fundamental period of vibration is
sec.
(2.16) (2.17)
use C = 2:75. 3. The other coe cients are: Z =0.3 I =1.25 RW =12
Victor Saouma
2{15
Light-framed walls with shear panels Plywood walls for structures three stories or less All other light-framed walls Shear walls Concrete Masonry Steel eccentrically braced ductile frame Light-framed walls with shear panels Plywood walls for structures three stories or less All other light-framed walls Shear walls Concrete Masonry Concentrically braced frames Steel Concrete (only for zones I and 2) Heavy timber
Special moment-resisting frames (SMRF) Steel 12 Concrete 12 Concrete intermediate moment-resisting frames (IMRF)only for zones 1 and 2 8 Ordinary moment-resisting frames (OMRF) Steel 6 Concrete (only for zone 1) 5 Dual systems (selected cases are for ductile rigid frames only) Shear walls Concrete with SMRF 12 Masonry with SMRF 8 Steel eccentrically braced ductile frame 6-12 Concentrically braced frame 12 Steel with steel SMRF 10 Steel with steel OMRF 6 Concrete with concrete SMRF (only for zones 1 and 2) 9 Table 2.12: Partial List of RW for Various Structure Systems, (UBC 1995)
Victor Saouma
Draft 2{16
4. Check 5. The total vertical load is
LOADS
C = 2:75 = 0:23 > 0:075p RW 12 W = 2 ((200 + 0:5(400)) (20) = 16000
lbs
7. Since T < 0:7 sec. there is no whiplash. 8. The load on each oor is thus given by
(2.21-a) (2.21-b)
Victor Saouma
2{17
300/2=150
2(300)/3=200
84000 k
3108 k
5(20)=100
Solution:
1. The total building weight is
ft
25 storeys = 84 000
7(25)=175
25(12)=300
sec.
> 0:7
sec.
4. The other coe cients are Z =0.4 I =1, RW =12 5. We check p C 1:12 R = 12 = 0:093 0:075
W
6. The total seismic base shear along the critical short direction is (0:4)(1)(1:12) W = 0:037W V = ZIC RW W = (12) = (0:037)(84000) = 3108 kip 7. Since T > 0:7
sec.
Victor Saouma
Draft 2{18
Hence the total triangular load is
LOADS
V ; Ft = 3108 ; 470 = 2638
k
(2.28)
8. let us check if wind load governs. From Table xx we conservatively assume a uniform wind pressure of 29 psf resulting in a total lateral force of PW = (0:029) (175 300) 2 = 1523 < 3108 (2.29) The magnitude of the total seismic load is clearly larger than the total wind force.
psf ft k k
q=K h
;sin where is the soil density, K = 1 1+sin is the pressure coe cient, h is the height.
39 40
(2.30)
For sand and gravel = 120 lb= ft3 , and 30 . If the structure is partially submerged, it must also resist hydrostatic pressure of water, Fig. 2.9.
q = Wh
where W = 62:4
lbs
(2.31)
= 3.
ft
Example 2-5: Hydrostatic Load Victor Saouma Structural Concepts and Systems for Architects
2{19
The basement of a building is 12 ft below grade. Ground water is located 9 ft below grade, what thickness concrete slab is required to exactly balance the hydrostatic uplift?
ft
The hydrostatic pressure must be countered by the pressure caused by the weight of concrete. Since p = h we equate the two pressures and solve for h the height of the concrete slab (62 :4) = 3 (12 ; 9) } = | {z water 3 h ) h = (62:4) = 3 (3) (12) 15.0 inch = 14 : 976 ' (150) = (150) = 3 | {z } concrete
lbs ft lbs ft ft in/ft in
2.4.2 Thermal
41
If a member is uniformly heated (or cooled) without restraint, then it will expand (or contract). This expansion is given by
l= l T
where is the coe cient of thermal expansion, Table 2.13 (/ F ) Steel 6:5 10;6 Concrete 5:5 10;6 Table 2.13: Coe cients of Thermal Expansion
42 43
(2.32)
If the member is restrained against expansion, then a compressive stress = E T is developed. To avoid excessive stresses due to thermal loading expansion joints are used in bridges and buildings.
Solution:
1. Assuming that the wall can move freely with no restraint from cross-walls and foundation, the wall expansion and contraction (summer and winter) are given by LSummer = TL = (3:6 10;6) = =oF (120 ; 60)o F (100) (12) = 0.26 (2.33-a) LWinter = TL = (3:6 10;6) = =oF (;20 ; 60)oF (100) (12) = -0.35 (2.33-b)
in in ft in/ft in in in ft in/ft in
Victor Saouma
Draft 2{20
Summer = E Winter = E
LOADS
2. We now assume (conservatively) that the free movement cannot occur ( L = 0) hence the resulting stress would be equal to = E" = E LL = E LTL = E T
lbs in
Tension (2.34-a)
2
lbs in
Note that the tensile stresses being beyond the masonary capacity, cracking will occur.
Live loads speci ed by codes represent the maximum possible loads. 45 The likelihood of all these loads occurring simultaneously is remote. Hence, building codes allow certain reduction when certain loads are combined together. 46 Furthermore, structures should be designed to resist a combination of loads. 47 Denoting D= dead L= live Lr= roof live W= wind E= earthquake S= snow T= temperature H= soil: 48 For the load and resistance factor design (LRFD) method of concrete structures, the American Concrete Institute (ACI) Building design code (318) (318 n.d.) requires that the following load combinations be considered: 1. 1.4D+1.7L 2. 0.75(1.4D+1.7L+1.7W) 3. 0.9D+1.3W 4. 1.4D +1.7L+1.7H 5. 0.75(1.4D+1.4T+1.7L) 6. 1.4(D+T) whereas for steel structures, the American Institute of Steel Construction (AISC) code, (of Steel COnstruction 1986) requires that the following combinations be veri ed 1. 1.4D 2. 1.2D+1.6L+0.5(Lr or S) 3. 1.2D+0.5L (or 0.8W)+1.6(Lr or S) 4. 1.2D+0.5L+0.5(Lr or S)+1.3W 5. 1.2D+0.5L(or 0.2 S)+1.5E
Victor Saouma
2{21
Analysis can be separately performed for each of the basic loads (L, D, W, etc) and then using the principle of superposition the loads can be linearly combined (unless the elastic limit has been reached). 50 Loads are often characterized as Usual, Unusual and Extreme.
Only the dead load is static. The live load on the other hand may or may not be applied on a given component of a structure. Hence, the load placement arrangement resulting in the highest internal forces (moment +ve or -ve, shear) at di erent locations must be considered, Fig. 2.10.
Whereas we will be focusing on the design of a reinforced concrete or steel section, we must keep in mind the following: 1. The section is part of a beam or girder. 2. The beam or girder is really part of a three dimensional structure in which load is transmitted from any point in the structure to the foundation through any one of various structural forms.
53
Load transfer in a structure is accomplished through a \hierarchy" of simple exural elements which are then connected to the columns, Fig. 2.11 or by two way slabs as illustrated in Fig. 2.12.
Under the action of the various forces and loadings described above, the structure must be able to respond with proper behavior, Fig. 9.1.
Victor Saouma
Draft 2{22
LOADS
Victor Saouma
2{23
Victor Saouma
Draft 2{24
LOADS
Victor Saouma
2{25
55 For preliminary analyses, the tributary area of a structural component will determine the total applied load.
1111111111 0000000000 0000000000 1111111111 0000000000 1111111111 0000000000 1111111111 0000000000 1111111111 0000000000 1111111111 0000000000 1111111111 0000000000 1111111111 0000000000 1111111111 0000000000 1111111111 0000000000 1111111111 1111111111 0000000000 0000000000 1111111111 0000000000 1111111111
00000 11111 11111 00000 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 11111 00000
00 11 0000 1111 00 11 11 00 0000 1111 00 11 00 11 0000 1111 00 11 00 11 0000 1111 00 11 00 11 0000 1111 00 11 00 11 0000 1111 00 11 00 11 0000 1111 00 11 00 11 0000 1111 00 11 00 11 0000 1111 00 11 11 1111 11 00 0000 00
Victor Saouma
Draft 2{26
LOADS
Victor Saouma
Draft
Chapter 3
STRUCTURAL MATERIALS
Proper understanding of structural materials is essential to both structural analysis and to structural design. 2 Characteristics of the most commonly used structural materials will be highlighted.
1
3.1 Steel
3
Draft 3{2
STRUCTURAL MATERIALS
Victor Saouma
3{3
The section modulus Sx of a W section can be roughly approximated by the following formula
2 Sx wd=10 or Ix Sx d 2 wd =20
(3.1)
Zx wd=9
11
(3.2)
Shapes Available
Shapes and bars
Use
(kksi)
(kksi)
Riveted, bolted, welded Buildings and bridges Cold formed welded and General structural purseamless sections pose Riveted, welded or bolted Hot formed welded and seam- Bolted and welded less sections Plates and bars in and less Building frames and thick trusses Bolted and welded Hot and cold rolled sheets Atmospheric corrosion resistant Cold rolled sheet in cut Cold formed sections lengths Structural shapes, plates and Bridges bars
1 2
36 up through 8 in. (32 above 8.) Grade A: 33 Grade B: 42 Grade C: 46 36 42 45-50 Grade C 33 Grade D 40 Grade E 80 Grade 36: 36 (to 4 in.) Grade 50: 50 Grade 100: 100 (to 2.5in.) and 90 (over 2.5 to 4 in.)
Rolled sections, Fig. 3.3 and welded ones, Fig3.4 have residual stresses. Those originate during the rolling or fabrication of a member. The member is hot just after rolling or welding, it cools unevenly because of varying exposure. The area that cool rst become sti er, resist contraction, and develop compressive stresses. The remaining regions continue to cool and contract in the plastic condition and develop tensile stresses. 13 Due to those residual stresses, the stress-strain curve of a rolled section exhibits a non-linear segment prior to the theoretical yielding, Fig. 3.5. This would have important implications on the exural and axial strength of beams and columns.
Victor Saouma
Draft 3{4
STRUCTURAL MATERIALS
say 40 ksi
20 ksi
Victor Saouma
3{5
.3 .2 .1
Members with residual stress
Fp
2 Average copressive strain Shaded portion indicates area which has achieved a stress F y
Figure 3.5: In uence of Residual Stress on Average Stress-Strain Curve of a Rolled Section
Steel is also used as reinforcing bars in concrete, Table 3.2. Those bars have a deformation on their surface to increase the bond with concrete, and usually have a yield stress of 60 ksi1 . Bar Designation No. 2 No. 3 No. 4 No. 5 No. 6 No. 7 No. 8 No. 9 No. 10 No. 11 No. 14 No. 18 Diameter Area Perimeter Weight (in.) ( 2) in lb/ft 2/8=0.250 0.05 0.79 0.167 3/8=0.375 0.11 1.18 0.376 4/8=0.500 0.20 1.57 0.668 5/8=0.625 0.31 1.96 1.043 6/8=0.750 0.44 2.36 1.5202 7/8=0.875 0.60 2.75 2.044 8/8=1.000 0.79 3.14 2.670 9/8=1.128 1.00 3.54 3.400 10/8=1.270 1.27 3.99 4.303 11/8=1.410 1.56 4.43 5.313 14/8=1.693 2.25 5.32 7.650 18/8=2.257 4.00 7.09 13.60
in
Steel loses its strength rapidly above 700 deg. F (and thus must be properly protected from re), and becomes brittle at ;30 deg. F 16 Steel is also used as wire strands and ropes for suspended roofs, cable-stayed bridges, fabric roofs and other structural applications. A strand is a helical arrangement of wires around a central wire. A rope consists of multiple strands helically wound around a central plastic core, and a modulus of elasticity of 20,000 ksi, and an ultimate strength of 220 ksi. 17 Prestressing Steel cables have an ultimate strength up to 270 ksi.
1
Stirrups which are used as vertical reinforcement to resist shear usually have a yield stress of only 40 ksi.
Victor Saouma
Draft 3{6
3.2 Aluminum
18
STRUCTURAL MATERIALS
Aluminum is used whenever light weight combined with strength is an important factor. Those properties, along with its resistance to corrosion have made it the material of choice for airplane structures, light roof framing. 19 Aluminum members can be connected by riveting, bolting and to a lesser extent by welding. 20 Aluminum has a modulus of elasticity equal to 10,000 ksi (about three times lower than steel), a coe cient of thermal expansion of 2:4 10;5 and a density of 173 = 3 . 21 The ultimate strength of pure aluminum is low (13,000 psi) but with the addition of alloys it can go up. 22 When aluminum is in contact with other metals in the presence of an electrolyte, galvanic corrosion may cause damage. Thus, steel and aluminum in a structure must be carefully separated by means of painting or a nonconductive material.
lbs ft
3.3 Concrete
Concrete is a mixture of Portland cement2 , water, and aggregates (usually sand and crushed stone). An ideal mixture is one in which: 1. A minimum amount of cement-water paste is used to ll the interstices between the particles of aggregates. 2. A minimum amount of water is provided to complete the chemical reaction with cement. In such a mixture, about 3/4 of the volume is constituted by the aggregates, and the remaining 1/4 being the cement paste. 24 Smaller particles up to 1/4 in. in size are called ne aggregates, and the larger ones being coarse aggregates. 25 Contrarily to steel to modulus of elasticity of concrete depends on the strength and is given by
23
E = 57 000 fc0
or
p E = 33 1:5 fc0 where both fc0 and E are in psi and is in = 3 .
lbs ft
(3.3) (3.4)
26
Typical concrete (compressive) strengths range from 3,000 to 6,000 psi However high strength
All concrete fail at an ultimate strain of 0.003, Fig. 3.1. Pre-peak nonlinearity is caused by micro-cracking Fig. 3.6. The tensile strength of concrete ft0 is about 10% of the compressive strength. Density of normal weight concrete is 145 = 3 and 100 = 3 for lightweight concrete.
lbs ft lbs ft
2
Portland cement is a mixture of calcareous and argillaceous materials which are calcined in a kiln and then pulverized. When mixed with water, cement hardens through a process called hydration.
Victor Saouma
3{7
Figure 3.6: Concrete microcracking Coe cient of thermal expansion is 0:65 10;5 /deg F for normal weight concrete. 32 When concrete is poured (or rather placed), the free water not needed for the hydration process evaporates over a period of time and the concrete will shrink. This shrinkage is about 0.05% after one year (strain). Thus if the concrete is restrained, then cracking will occur3. 33 Concrete will also deform with time due to the applied load, this is called creep. This should be taken into consideration when computing the de ections (which can be up to three times the instantaneous elastic de ection).
31
3.4 Masonry
34
Masonry consists of either natural materials, such as stones, or of manufactured products such as bricks and concrete blocks4, stacked and bonded together with mortar. 35 As for concrete, all modern structural masonry blocks are essentially compression members with low tensile resistance. 36 The mortar used is a mixture of sand, masonry cement, and either Portland cement or hydrated lime.
3.5 Timber
Timber is one of the earliest construction materials, and one of the few natural materials with good tensile properties. 38 The properties of timber vary greatly, and the strength is time dependent. 39 Timber is a good shock absorber (many wood structures in Japan have resisted repeated earthquakes). 40 The most commonly used species of timber in construction are Douglas r, southern pine, hemlock and larch. 41 Members can be laminated together under good quality control, and exural strengths as high as 2,500 psi can be achieved.
37
For this reason a minimum amount of reinforcement is always necessary in concrete, and a 2% reinforcement, can reduce the shrinkage by 75%. Mud bricks were used by the Babylonians, stones by the Egyptians, and ice blocks by the Eskimos...
3 4
Victor Saouma
fc
Draft 3{8
3.6 Steel Section Properties
42
STRUCTURAL MATERIALS
Dimensions and properties of rolled sections are tabulated in the following pages, Fig. 3.7.
Victor Saouma
3{9
2t
Victor Saouma
A in 249.0 234.0 211.0 190.0 172.0 154.0 142.0 128.0 115.0 105.0 96.4 88.3 82.4 76.5 72.1 67.6 75.4 68.1 61.8 57.0 53.6 50.0 47.0 44.2 39.7 181.0 166.0 151.0 137.0 124.0 113.0 104.0 93.5 85.6 77.4 70.9 65.0 59.1 49.5 44.7 41.6 38.3 34.7 170.0 154.0 140.0 127.0 114.0 104.0 95.7 85.7 76.7 69.0 62.0 56.1 50.8 43.5 38.9 36.5 34.2 31.7 29.1 26.4
2
d in 42.45 41.97 41.19 40.47 39.84 39.21 38.74 38.26 37.80 37.40 37.09 36.74 36.52 36.26 36.08 35.90 37.43 37.12 36.69 36.49 36.33 36.17 36.01 35.85 35.55 38.47 37.91 37.36 36.81 36.34 35.95 35.55 35.16 34.84 34.53 34.18 33.93 33.68 33.82 33.49 33.30 33.09 32.86 35.39 34.76 34.21 33.66 33.19 32.80 32.40 32.01 31.61 31.30 30.94 30.68 30.44 30.67 30.31 30.17 30.01 29.83 29.65 29.53
bf
hc tw
2.0 2.1 2.3 2.5 2.7 3.0 3.2 3.5 3.8 4.2 4.5 5.0 5.3 5.7 6.1 6.5 3.5 3.9 4.5 4.8 5.1 5.5 5.9 6.4 7.6 2.4 2.6 2.8 3.0 3.3 3.6 3.8 4.2 4.6 5.0 5.7 6.2 6.8 4.7 5.5 6.0 6.7 7.8 2.3 2.5 2.7 2.9 3.2 3.5 3.7 4.1 4.6 5.0 5.7 6.3 7.0 4.4 5.3 5.7 6.2 6.9 7.8 8.5
12.5 13.2 14.5 16.0 17.6 19.6 21.0 23.1 25.8 28.1 30.9 33.3 35.6 37.5 39.4 41.4 33.8 37.3 39.1 42.4 44.8 47.8 50.0 52.0 54.1 15.2 16.6 18.2 19.7 21.7 23.8 25.8 28.8 31.2 34.5 36.1 38.7 41.9 44.7 47.2 49.6 51.7 54.5 13.7 15.1 16.6 18.0 19.9 21.8 23.7 26.5 29.0 32.5 34.9 38.0 41.2 41.5 43.9 46.2 47.8 49.6 51.9 57.5
Ix in 67400 62600 55300 48900 43500 38300 34700 31000 27500 24800 22500 20300 18900 17300 16100 15000 16800 15000 13200 12100 11300 10500 9750 9040 7800 41800 37700 33700 30100 26900 24300 21900 19500 17700 15800 14200 12800 11500 9290 8160 7450 6710 5900 33000 29300 26100 23200 20700 18600 16800 14900 13100 11700 10300 9170 8200 6680 5770 5360 4930 4470 3990 3620
4
Sx in 3170 2980 2690 2420 2180 1950 1790 1620 1450 1320 1210 1110 1030 953 895 837 895 809 719 664 623 580 542 504 439 2170 1990 1810 1630 1480 1350 1230 1110 1010 917 829 757 684 549 487 448 406 359 1870 1680 1530 1380 1250 1140 1030 928 827 746 663 598 539 436 380 355 329 299 269 245
3
Iy in 4550 4200 3680 3230 2850 2490 2250 1990 1750 1570 1420 1300 1200 1090 1010 940 528 468 411 375 347 320 295 270 225 2870 2580 2290 2030 1800 1620 1460 1290 1160 1030 932 840 749 310 273 246 218 187 2530 2230 1970 1750 1550 1390 1240 1100 959 855 757 673 598 227 196 181 164 146 128 115
4
Sy in 501 467 414 367 328 289 263 235 208 188 171 156 144 132 123 114 86 77 68 62 58 53 49 45 38 340 308 276 247 221 200 181 161 146 131 118 106 95 54 47 43 38 33 312 278 249 222 198 179 162 144 127 114 100 90 80 43 37 34 31 28 24 22
3
Zx in 3830.0 3570.0 3190.0 2840.0 2550.0 2270.0 2070.0 1860.0 1660.0 1510.0 1380.0 1260.0 1170.0 1080.0 1010.0 943.0 1040.0 936.0 833.0 767.0 718.0 668.0 624.0 581.0 509.0 2560.0 2330.0 2110.0 1890.0 1700.0 1550.0 1420.0 1270.0 1150.0 1040.0 939.0 855.0 772.0 629.0 559.0 514.0 467.0 415.0 2210.0 1990.0 1790.0 1610.0 1430.0 1300.0 1190.0 1060.0 941.0 845.0 749.0 673.0 605.0 500.0 437.0 408.0 378.0 346.0 312.0 283.0
3
Zy in 799.0 743.0 656.0 580.0 517.0 454.0 412.0 367.0 325.0 292.0 265.0 241.0 223.0 204.0 190.0 176.0 137.0 122.0 107.0 97.7 90.7 83.8 77.3 70.9 59.7 537.0 485.0 433.0 387.0 345.0 312.0 282.0 250.0 226.0 202.0 182.0 164.0 147.0 84.4 73.9 66.9 59.5 51.3 492.0 438.0 390.0 348.0 310.0 279.0 252.0 223.0 196.0 175.0 154.0 138.0 123.0 68.0 58.4 54.0 49.2 43.9 38.6 34.7
3
Draft 3{10
Designation W 27x539 W 27x494 W 27x448 W 27x407 W 27x368 W 27x336 W 27x307 W 27x281 W 27x258 W 27x235 W 27x217 W 27x194 W 27x178 W 27x161 W 27x146 W 27x129 W 27x114 W 27x102 W 27x 94 W 27x 84 W 24x492 W 24x450 W 24x408 W 24x370 W 24x335 W 24x306 W 24x279 W 24x250 W 24x229 W 24x207 W 24x192 W 24x176 W 24x162 W 24x146 W 24x131 W 24x117 W 24x104 W 24x103 W 24x 94 W 24x 84 W 24x 76 W 24x 68 W 24x 62 W 24x 55 W 21x402 W 21x364 W 21x333 W 21x300 W 21x275 W 21x248 W 21x223 W 21x201 W 21x182 W 21x166 W 21x147 W 21x132 W 21x122 W 21x111 W 21x101 W 21x 93 W 21x 83 W 21x 73
STRUCTURAL MATERIALS
A in 158.0 145.0 131.0 119.0 108.0 98.7 90.2 82.6 75.7 69.1 63.8 57.0 52.3 47.4 42.9 37.8 33.5 30.0 27.7 24.8 144.0 132.0 119.0 108.0 98.4 89.8 82.0 73.5 67.2 60.7 56.3 51.7 47.7 43.0 38.5 34.4 30.6 30.3 27.7 24.7 22.4 20.1 18.2 16.2 118.0 107.0 97.9 88.2 80.8 72.8 65.4 59.2 53.6 48.8 43.2 38.8 35.9 32.7 29.8 27.3 24.3 21.5
2
d in 32.52 31.97 31.42 30.87 30.39 30.00 29.61 29.29 28.98 28.66 28.43 28.11 27.81 27.59 27.38 27.63 27.29 27.09 26.92 26.71 29.65 29.09 28.54 27.99 27.52 27.13 26.73 26.34 26.02 25.71 25.47 25.24 25.00 24.74 24.48 24.26 24.06 24.53 24.31 24.10 23.92 23.73 23.74 23.57 26.02 25.47 25.00 24.53 24.13 23.74 23.35 23.03 22.72 22.48 22.06 21.83 21.68 21.51 21.36 21.62 21.43 21.24
2t
bf
hc tw
2.2 2.3 2.5 2.7 3.0 3.2 3.5 3.7 4.0 4.4 4.7 5.2 5.9 6.5 7.2 4.5 5.4 6.0 6.7 7.8 2.0 2.1 2.3 2.5 2.7 2.9 3.2 3.5 3.8 4.1 4.4 4.8 5.3 5.9 6.7 7.5 8.5 4.6 5.2 5.9 6.6 7.7 6.0 6.9 2.1 2.3 2.5 2.7 2.9 3.2 3.5 3.9 4.2 4.6 5.4 6.0 6.5 7.1 7.7 4.5 5.0 5.6
12.3 13.4 14.7 15.9 17.6 19.2 20.9 22.9 24.7 26.6 29.2 32.3 33.4 36.7 40.0 39.7 42.5 47.0 49.4 52.7 10.9 11.9 13.1 14.2 15.6 17.1 18.6 20.7 22.5 24.8 26.6 28.7 30.6 33.2 35.6 39.2 43.1 39.2 41.9 45.9 49.0 52.0 50.1 54.6 10.8 11.8 12.8 14.2 15.4 17.1 18.8 20.6 22.6 24.9 26.1 28.9 31.3 34.1 37.5 32.3 36.4 41.2
Ix in 25500 22900 20400 18100 16100 14500 13100 11900 10800 9660 8870 7820 6990 6280 5630 4760 4090 3620 3270 2850 19100 17100 15100 13400 11900 10700 9600 8490 7650 6820 6260 5680 5170 4580 4020 3540 3100 3000 2700 2370 2100 1830 1550 1350 12200 10800 9610 8480 7620 6760 5950 5310 4730 4280 3630 3220 2960 2670 2420 2070 1830 1600
4
Sx in 1570 1440 1300 1170 1060 970 884 811 742 674 624 556 502 455 411 345 299 267 243 213 1290 1170 1060 957 864 789 718 644 588 531 491 450 414 371 329 291 258 245 222 196 176 154 131 114 937 846 769 692 632 569 510 461 417 380 329 295 273 249 227 192 171 151
3
Iy in 2110 1890 1670 1480 1310 1170 1050 953 859 768 704 618 555 497 443 184 159 139 124 106 1670 1490 1320 1160 1030 919 823 724 651 578 530 479 443 391 340 297 259 119 109 94 82 70 34 29 1270 1120 994 873 785 694 609 542 483 435 376 333 305 274 248 93 81 71
4
Sy in 277 250 224 200 179 161 146 133 120 108 100 88 79 71 64 37 32 28 25 21 237 214 191 170 152 137 124 110 99 89 82 74 68 60 53 46 41 26 24 21 18 16 10 8 189 168 151 134 122 109 96 86 77 70 60 54 49 44 40 22 20 17
3
Zx in 1880.0 1710.0 1530.0 1380.0 1240.0 1130.0 1020.0 933.0 850.0 769.0 708.0 628.0 567.0 512.0 461.0 395.0 343.0 305.0 278.0 244.0 1550.0 1410.0 1250.0 1120.0 1020.0 922.0 835.0 744.0 676.0 606.0 559.0 511.0 468.0 418.0 370.0 327.0 289.0 280.0 254.0 224.0 200.0 177.0 153.0 134.0 1130.0 1010.0 915.0 816.0 741.0 663.0 589.0 530.0 476.0 432.0 373.0 333.0 307.0 279.0 253.0 221.0 196.0 172.0
3
Zy in 437.0 394.0 351.0 313.0 279.0 252.0 227.0 206.0 187.0 168.0 154.0 136.0 122.0 109.0 97.5 57.6 49.3 43.4 38.8 33.2 375.0 337.0 300.0 267.0 238.0 214.0 193.0 171.0 154.0 137.0 126.0 115.0 105.0 93.2 81.5 71.4 62.4 41.5 37.5 32.6 28.6 24.5 15.7 13.3 296.0 263.0 237.0 210.0 189.0 169.0 149.0 133.0 119.0 108.0 92.6 82.3 75.6 68.2 61.7 34.7 30.5 26.6
3
Victor Saouma
3{11
2 4 3 4 3 3 3
Victor Saouma
A in 20.0 18.3 16.7 14.7 13.0 91.5 83.2 75.9 68.8 62.1 56.4 51.3 46.3 42.1 38.2 35.1 31.1 28.5 25.3 22.3 20.8 19.1 17.6 16.2 14.7 13.5 11.8 10.3 29.4 26.2 22.6 19.7 16.8 14.7 13.3 11.8 10.6 9.1 7.7 215.0 196.0 178.0 162.0 147.0 134.0 125.0 117.0 109.0 101.0 91.4 83.3 75.6 68.5 62.0 56.8 51.8 46.7 42.7 38.8 35.3 32.0 29.1 26.5 24.1
2
hc d btff Ix Sx Iy Sy Zx Zy tw in in in in in in in 21.13 6.0 43.6 1480 140 65 16 160.0 24.4 20.99 6.7 46.9 1330 127 58 14 144.0 21.7 21.06 5.0 46.3 1170 111 31 9 129.0 14.8 20.83 6.1 49.4 984 94 25 8 110.0 12.2 20.66 7.2 53.6 843 82 21 6 95.4 10.2 22.32 2.2 10.6 6960 624 795 132 753.0 207.0 21.85 2.4 11.5 6160 564 704 118 676.0 185.0 21.46 2.6 12.5 5510 514 628 107 611.0 166.0 21.06 2.8 13.8 4900 466 558 96 549.0 149.0 20.67 3.0 15.1 4330 419 493 85 490.0 132.0 20.35 3.3 16.7 3870 380 440 77 442.0 119.0 20.04 3.6 18.0 3450 344 391 69 398.0 106.0 19.72 3.9 19.8 3060 310 347 61 356.0 94.8 19.49 4.2 21.9 2750 282 311 56 322.0 85.4 19.25 4.6 23.9 2460 256 278 50 291.0 76.7 18.97 5.3 24.5 2190 231 253 45 261.0 69.1 18.73 6.0 27.2 1910 204 220 39 230.0 60.5 18.59 6.4 30.0 1750 188 201 36 211.0 55.3 18.39 7.2 33.4 1530 166 175 32 186.0 48.4 18.21 8.1 37.8 1330 146 152 28 163.0 42.2 18.47 4.7 32.4 1170 127 60 16 145.0 24.7 18.35 5.1 35.7 1070 117 55 14 133.0 22.5 18.24 5.4 38.7 984 108 50 13 123.0 20.6 18.11 6.0 41.2 890 98 45 12 112.0 18.5 17.99 6.6 45.2 800 89 40 11 101.0 16.6 18.06 5.0 44.6 712 79 22 7 90.7 11.7 17.90 5.7 51.0 612 68 19 6 78.4 9.9 17.70 7.1 53.5 510 58 15 5 66.5 8.1 16.97 5.3 24.3 1490 175 186 36 198.0 54.9 16.75 5.9 27.0 1300 155 163 31 175.0 48.1 16.52 6.8 31.2 1110 134 138 27 150.0 41.1 16.33 7.7 35.9 954 117 119 23 130.0 35.5 16.43 5.0 33.0 758 92 43 12 105.0 18.9 16.26 5.6 37.4 659 81 37 10 92.0 16.3 16.13 6.2 41.2 586 73 33 9 82.3 14.5 16.01 6.9 46.6 518 65 29 8 72.9 12.7 15.86 8.1 48.1 448 56 24 7 64.0 10.8 15.88 6.3 51.6 375 47 12 4 54.0 7.0 15.69 8.0 56.8 301 38 10 3 44.2 5.5 22.42 1.8 3.7 14300 1280 4720 527 1660.0 816.0 21.64 2.0 4.0 12400 1150 4170 472 1480.0 730.0 20.92 2.1 4.4 10800 1040 3680 423 1320.0 652.0 20.24 2.3 4.8 9430 931 3250 378 1180.0 583.0 19.60 2.4 5.2 8210 838 2880 339 1050.0 522.0 19.02 2.6 5.7 7190 756 2560 304 936.0 468.0 18.67 2.8 6.1 6600 707 2360 283 869.0 434.0 18.29 2.9 6.4 6000 656 2170 262 801.0 402.0 17.92 3.1 6.9 5440 607 1990 241 736.0 370.0 17.54 3.3 7.4 4900 559 1810 221 672.0 338.0 17.12 3.6 8.1 4330 506 1610 199 603.0 304.0 16.74 3.9 8.8 3840 459 1440 179 542.0 274.0 16.38 4.2 9.7 3400 415 1290 161 487.0 246.0 16.04 4.6 10.7 3010 375 1150 145 436.0 221.0 15.72 5.1 11.6 2660 338 1030 130 390.0 198.0 15.48 5.5 12.8 2400 310 931 119 355.0 180.0 15.22 6.0 13.7 2140 281 838 107 320.0 163.0 14.98 6.5 15.3 1900 254 748 96 287.0 146.0 14.78 7.1 16.8 1710 232 677 87 260.0 133.0 14.66 7.1 17.7 1530 209 548 74 234.0 113.0 14.48 7.8 19.3 1380 190 495 68 212.0 102.0 14.32 8.5 21.7 1240 173 447 61 192.0 92.7 14.16 9.3 23.5 1110 157 402 55 173.0 83.6 14.02 10.2 25.9 999 143 362 50 157.0 75.6 14.31 5.9 22.4 882 123 148 29 139.0 44.8
Draft 3{12
Designation W 14x 74 W 14x 68 W 14x 61 W 14x 53 W 14x 48 W 14x 43 W 14x 38 W 14x 34 W 14x 30 W 14x 26 W 14x 22 W 12x336 W 12x305 W 12x279 W 12x252 W 12x230 W 12x210 W 12x190 W 12x170 W 12x152 W 12x136 W 12x120 W 12x106 W 12x 96 W 12x 87 W 12x 79 W 12x 72 W 12x 65 W 12x 58 W 12x 53 W 12x 50 W 12x 45 W 12x 40 W 12x 35 W 12x 30 W 12x 26 W 12x 22 W 12x 19 W 12x 16 W 12x 14 W 10x112 W 10x100 W 10x 88 W 10x 77 W 10x 68 W 10x 60 W 10x 54 W 10x 49 W 10x 45 W 10x 39 W 10x 33 W 10x 30 W 10x 26 W 10x 22 W 10x 19 W 10x 17 W 10x 15 W 10x 12
STRUCTURAL MATERIALS
A in 21.8 20.0 17.9 15.6 14.1 12.6 11.2 10.0 8.9 7.7 6.5 98.8 89.6 81.9 74.1 67.7 61.8 55.8 50.0 44.7 39.9 35.3 31.2 28.2 25.6 23.2 21.1 19.1 17.0 15.6 14.7 13.2 11.8 10.3 8.8 7.7 6.5 5.6 4.7 4.2 32.9 29.4 25.9 22.6 20.0 17.6 15.8 14.4 13.3 11.5 9.7 8.8 7.6 6.5 5.6 5.0 4.4 3.5
2
d in 14.17 14.04 13.89 13.92 13.79 13.66 14.10 13.98 13.84 13.91 13.74 16.82 16.32 15.85 15.41 15.05 14.71 14.38 14.03 13.71 13.41 13.12 12.89 12.71 12.53 12.38 12.25 12.12 12.19 12.06 12.19 12.06 11.94 12.50 12.34 12.22 12.31 12.16 11.99 11.91 11.36 11.10 10.84 10.60 10.40 10.22 10.09 9.98 10.10 9.92 9.73 10.47 10.33 10.17 10.24 10.11 9.99 9.87
2t
bf
hc tw
6.4 7.0 7.7 6.1 6.7 7.5 6.6 7.4 8.7 6.0 7.5 2.3 2.4 2.7 2.9 3.1 3.4 3.7 4.0 4.5 5.0 5.6 6.2 6.8 7.5 8.2 9.0 9.9 7.8 8.7 6.3 7.0 7.8 6.3 7.4 8.5 4.7 5.7 7.5 8.8 4.2 4.6 5.2 5.9 6.6 7.4 8.2 8.9 6.5 7.5 9.1 5.7 6.6 8.0 5.1 6.1 7.4 9.4
25.3 27.5 30.4 30.8 33.5 37.4 39.6 43.1 45.4 48.1 53.3 5.5 6.0 6.3 7.0 7.6 8.2 9.2 10.1 11.2 12.3 13.7 15.9 17.7 18.9 20.7 22.6 24.9 27.0 28.1 26.2 29.0 32.9 36.2 41.8 47.2 41.8 46.2 49.4 54.3 10.4 11.6 13.0 14.8 16.7 18.7 21.2 23.1 22.5 25.0 27.1 29.5 34.0 36.9 35.4 36.9 38.5 46.6
Ix in 796 723 640 541 485 428 385 340 291 245 199 4060 3550 3110 2720 2420 2140 1890 1650 1430 1240 1070 933 833 740 662 597 533 475 425 394 350 310 285 238 204 156 130 103 89 716 623 534 455 394 341 303 272 248 209 170 170 144 118 96 82 69 54
4
Sx Iy Sy Zx Zy in in in in in 112 134 27 126.0 40.6 103 121 24 115.0 36.9 92 107 22 102.0 32.8 78 58 14 87.1 22.0 70 51 13 78.4 19.6 63 45 11 69.6 17.3 55 27 8 61.5 12.1 49 23 7 54.6 10.6 42 20 6 47.3 9.0 35 9 4 40.2 5.5 29 7 3 33.2 4.4 483 1190 177 603.0 274.0 435 1050 159 537.0 244.0 393 937 143 481.0 220.0 353 828 127 428.0 196.0 321 742 115 386.0 177.0 292 664 104 348.0 159.0 263 589 93 311.0 143.0 235 517 82 275.0 126.0 209 454 73 243.0 111.0 186 398 64 214.0 98.0 163 345 56 186.0 85.4 145 301 49 164.0 75.1 131 270 44 147.0 67.5 118 241 40 132.0 60.4 107 216 36 119.0 54.3 97 195 32 108.0 49.2 88 174 29 96.8 44.1 78 107 21 86.4 32.5 71 96 19 77.9 29.1 65 56 14 72.4 21.4 58 50 12 64.7 19.0 52 44 11 57.5 16.8 46 24 7 51.2 11.5 39 20 6 43.1 9.6 33 17 5 37.2 8.2 25 5 2 29.3 3.7 21 4 2 24.7 3.0 17 3 1 20.1 2.3 15 2 1 17.4 1.9 126 236 45 147.0 69.2 112 207 40 130.0 61.0 98 179 35 113.0 53.1 86 154 30 97.6 45.9 76 134 26 85.3 40.1 67 116 23 74.6 35.0 60 103 21 66.6 31.3 55 93 19 60.4 28.3 49 53 13 54.9 20.3 42 45 11 46.8 17.2 35 37 9 38.8 14.0 32 17 6 36.6 8.8 28 14 5 31.3 7.5 23 11 4 26.0 6.1 19 4 2 21.6 3.3 16 4 2 18.7 2.8 14 3 1 16.0 2.3 11 2 1 12.6 1.7
3 4 3 3 3
Victor Saouma
3{13
2 4 3 4 3
Victor Saouma
A in 19.7 17.1 14.1 11.7 10.3 9.1 8.2 7.1 6.2 5.3 4.4 3.8 3.0 7.3 5.9 4.4 4.7 3.5 2.7 5.5 4.7 3.8 5.1 3.5 3.2 2.9 2.7 2.3 2.2 1.9 1.3 5.6 35.6 31.2 29.3 26.5 23.5 28.2 25.3 22.0 19.4 20.6 16.1 14.7 12.6 14.7 12.0 10.3 9.4 10.3 7.5 6.8 5.4 5.9 4.5 5.1 3.7 4.3 2.9 2.8 2.3 2.2 1.7
2
hc d btff Ix Sx Iy Sy tw in in in in in 9.00 4.4 11.1 272 60 89 21 8.75 5.1 12.4 228 52 75 18 8.50 5.9 15.8 184 43 61 15 8.25 7.2 17.6 146 36 49 12 8.12 8.1 20.4 127 31 43 11 8.00 9.2 22.2 110 28 37 9 8.06 7.0 22.2 98 24 22 7 7.93 8.1 25.8 83 21 18 6 8.28 6.6 27.5 75 18 10 4 8.14 8.0 29.9 62 15 8 3 8.11 6.4 28.1 48 12 3 2 7.99 7.8 29.9 40 10 3 1 7.89 9.6 40.5 31 8 2 1 6.38 6.7 15.5 53 17 17 6 6.20 8.2 19.1 41 13 13 4 5.99 11.5 21.6 29 10 9 3 6.28 5.0 19.1 32 10 4 2 6.03 7.1 21.6 22 7 3 2 5.90 9.2 29.2 16 6 2 1 5.15 5.8 14.0 26 10 9 4 5.01 6.9 15.8 21 9 8 3 4.16 5.9 10.6 11 5 4 2 14.00 7.4 60.3 148 21 3 1 12.00 6.8 62.5 72 12 1 1 11.97 7.3 63.6 65 11 1 1 11.97 9.1 68.0 62 10 1 1 10.00 6.5 58.4 39 8 1 0 9.95 7.4 59.3 34 7 1 0 9.99 7.8 65.0 33 7 0 0 8.00 6.0 53.8 18 5 0 0 6.00 5.4 47.0 7 2 0 0 5.00 6.0 11.2 24 10 8 3 24.50 3.7 26.4 3160 258 83 21 24.50 3.6 34.1 2940 240 77 20 24.00 4.2 28.3 2390 199 48 13 24.00 4.1 33.7 2250 187 45 13 24.00 4.0 42.1 2100 175 42 12 20.30 3.9 21.6 1670 165 50 14 20.30 3.8 26.2 1580 155 47 13 20.00 4.0 27.1 1280 128 30 9 20.00 3.9 34.1 1190 119 28 9 18.00 4.5 21.8 926 103 24 8 18.00 4.3 33.6 804 89 21 7 15.00 4.5 23.2 486 65 16 6 15.00 4.4 31.0 447 60 14 5 12.00 4.2 13.9 305 51 16 6 12.00 4.0 20.7 272 45 14 5 12.00 4.7 23.4 229 38 10 4 12.00 4.6 28.6 218 36 9 4 10.00 5.0 13.8 147 29 8 3 10.00 4.7 26.4 124 25 7 3 8.00 4.9 14.5 65 16 4 2 8.00 4.7 23.7 58 14 4 2 7.00 4.9 12.3 42 12 3 2 7.00 4.7 21.9 37 10 3 1 6.00 5.0 9.9 26 9 2 1 6.00 4.6 19.9 22 7 2 1 5.00 5.0 7.5 15 6 2 1 5.00 4.6 17.4 12 5 1 1 4.00 4.8 8.7 7 3 1 1 4.00 4.5 14.7 6 3 1 1 3.00 4.8 5.6 3 2 1 0 3.00 4.5 11.4 3 2 0 0
Zx in 70.2 59.8 49.0 39.8 34.7 30.4 27.2 23.2 20.4 17.0 13.6 11.4 8.9 18.9 14.9 10.8 11.7 8.3 6.2 11.6 9.6 6.3 24.9 14.3 13.2 12.2 9.2 8.2 7.7 5.4 2.8 11.0 306.0 279.0 240.0 222.0 204.0 198.0 183.0 153.0 140.0 125.0 105.0 77.1 69.3 61.2 53.1 44.8 42.0 35.4 28.4 19.3 16.5 14.5 12.1 10.6 8.5 7.4 5.7 4.0 3.5 2.4 2.0
3
Zy in 32.7 27.9 22.9 18.5 16.1 14.1 10.1 8.6 5.7 4.7 2.7 2.2 1.7 8.6 6.7 4.8 3.4 2.3 1.7 5.5 4.6 2.9 2.2 1.1 1.0 1.0 0.8 0.7 0.6 0.5 0.3 5.0 36.2 33.2 23.9 22.3 20.7 24.9 23.0 16.7 15.3 14.4 12.1 10.0 9.0 10.3 8.9 6.8 6.4 6.2 5.0 3.7 3.2 3.0 2.4 2.4 1.9 1.9 1.4 1.1 1.0 0.8 0.7
3
Draft 3{14
Designation
STRUCTURAL MATERIALS
2
A in C 15.x 50 14.7 C 15.x 40 11.8 C 15.x 34 10.0 C 12.x 30 8.8 C 12.x 25 7.3 C 12.x 21 6.1 C 10.x 30 8.8 C 10.x 25 7.3 C 10.x 20 5.9 C 10.x 15 4.5 C 9.x 20 5.9 C 9.x 15 4.4 C 9.x 13 3.9 C 8.x 19 5.5 C 8.x 14 4.0 C 8.x 12 3.4 C 7.x 15 4.3 C 7.x 12 3.6 C 7.x 10 2.9 C 6.x 13 3.8 C 6.x 11 3.1 C 6.x 8 2.4 C 5.x 9 2.6 C 5.x 7 2.0 C 4.x 7 2.1 C 4.x 5 1.6 C 3.x 6 1.8 C 3.x 5 1.5 C 3.x 4 1.2 Designation
L 8.0x4.0x1.000 L 8.0x4.0x0.750 L 8.0x4.0x0.563 L 8.0x4.0x0.500 L 7.0x4.0x0.750 L 7.0x4.0x0.625 L 7.0x4.0x0.500 L 7.0x4.0x0.375 L 6.0x6.0x1.000 L 6.0x6.0x0.875 L 6.0x6.0x0.750 L 6.0x6.0x0.625 L 6.0x6.0x0.563 L 6.0x6.0x0.500 L 6.0x6.0x0.438 L 6.0x6.0x0.375 L 6.0x6.0x0.313 L 6.0x4.0x0.875 L 6.0x4.0x0.750 L 6.0x4.0x0.625 L 6.0x4.0x0.563 L 6.0x4.0x0.500 L 6.0x4.0x0.438 L 6.0x4.0x0.375 L 6.0x4.0x0.313 L 6.0x3.5x0.500 L 6.0x3.5x0.375 L 6.0x3.5x0.313
d in 15. 15. 15. 12. 12. 12. 10. 10. 10. 10. 9. 9. 9. 8. 8. 8. 7. 7. 7. 6. 6. 6. 5. 5. 4. 4. 3. 3. 3. A in 11.00 8.44 6.43 5.75 7.69 6.48 5.25 3.98 11.00 9.73 8.44 7.11 6.43 5.75 5.06 4.36 3.65 7.98 6.94 5.86 5.31 4.75 4.18 3.61 3.03 4.50 3.42 2.87
2
2t
bf
hc tw
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 wgt k=ft 37.40 28.70 21.90 19.60 26.20 22.10 17.90 13.60 37.40 33.10 28.70 24.20 21.90 19.60 17.20 14.90 12.40 27.20 23.60 20.00 18.10 16.20 14.30 12.30 10.30 15.30 11.70 9.80
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Ix in 69.6 54.9 42.8 38.5 37.8 32.4 26.7 20.6 35.5 31.9 28.2 24.2 22.1 19.9 17.7 15.4 13.0 27.7 24.5 21.1 19.3 17.4 15.5 13.5 11.4 16.6 12.9 10.9
4
Ix in 404.0 349.0 315.0 162.0 144.0 129.0 103.0 91.2 78.9 67.4 60.9 51.0 47.9 44.0 36.1 32.6 27.2 24.2 21.3 17.4 15.2 13.1 8.9 7.5 4.6 3.8 2.1 1.9 1.7 Sx in 14.1 10.9 8.4 7.5 8.4 7.1 5.8 4.4 8.6 7.6 6.7 5.7 5.1 4.6 4.1 3.5 3.0 7.2 6.3 5.3 4.8 4.3 3.8 3.3 2.8 4.2 3.2 2.7
4 3
Sx in 53.8 46.5 42.0 27.0 24.1 21.5 20.7 18.2 15.8 13.5 13.5 11.3 10.6 11.0 9.0 8.1 7.8 6.9 6.1 5.8 5.1 4.4 3.6 3.0 2.3 1.9 1.4 1.2 1.1 Iy in 11.60 9.36 7.43 6.74 9.05 7.84 6.53 5.10 35.50 31.90 28.20 24.20 22.10 19.90 17.70 15.40 13.00 9.75 8.68 7.52 6.91 6.27 5.60 4.90 4.18 4.25 3.34 2.85
3 4
Iy in 11. 9.23 8.13 5.14 4.47 3.88 3.94 3.36 2.81 2.28 2.42 1.93 1.76 1.98 1.53 1.32 1.38 1.17 0.97 1.05 0.87 0.69 0.63 0.48 0.43 0.32 0.31 0.25 0.20 Sy in 3.94 3.07 2.38 2.15 3.03 2.58 2.12 1.63 8.57 7.63 6.66 5.66 5.14 4.61 4.08 3.53 2.97 3.39 2.97 2.54 2.31 2.08 1.85 1.60 1.35 1.59 1.23 1.04
4 3
Sy Zx Zy in in in 3.78 8.20 8.17 3.37 57.20 6.87 3.11 50.40 6.23 2.06 33.60 4.33 1.88 29.20 3.84 1.73 25.40 3.49 1.65 26.60 3.78 1.48 23. 3.19 1.32 19.30 2.71 1.16 15.80 2.35 1.17 16.80 2.47 1.01 13.50 2.05 0.96 12.50 1.95 1.01 13.80 2.17 0.85 10.90 1.73 0.78 9.55 1.58 0.78 9.68 1.64 0.70 8.40 1.43 0.63 7.12 1.26 0.64 7.26 1.36 0.56 6.15 1.15 0.49 5.13 0.99 0.45 4.36 0.92 0.38 3.51 0.76 0.34 2.81 0.70 0.28 2.26 0.57 0.27 1.72 0.54 0.23 1.50 0.47 0.20 1.30 0.40 Zx Zy in in 24.30 7.72 18.90 5.81 14.50 4.38 13.00 3.90 14.80 5.65 12.60 4.74 10.30 3.83 7.87 2.90 15.50 15.50 13.80 13.80 12.00 12.00 10.20 10.20 9.26 9.26 8.31 8.31 7.34 7.34 6.35 6.35 5.35 5.35 12.70 6.31 11.20 5.47 9.51 4.62 8.66 4.19 7.78 3.75 6.88 3.30 5.97 2.85 5.03 2.40 7.50 2.91 5.76 2.20 4.85 1.85
3 3 3 3 3
Victor Saouma
3{15
Ix Sx in in 17.8 5.2 15.7 4.5 13.6 3.9 11.3 3.2 10.0 2.8 8.7 2.4 7.4 2.0 13.9 4.3 12.0 3.7 10.0 3.0 8.9 2.6 7.8 2.3 6.6 1.9 5.4 1.6 11.4 3.5 9.4 2.9 8.4 2.6 7.4 2.2 6.3 1.9 5.1 1.5 7.7 2.8 6.7 2.4 5.6 2.0 5.0 1.8 4.4 1.5 3.7 1.3 3.0 1.0 5.3 1.9 4.8 1.7 4.2 1.5 3.6 1.3 2.9 1.0 5.1 1.9 4.5 1.7
4 3
A in 7.98 6.94 5.86 4.75 4.18 3.61 3.03 5.81 4.92 4.00 3.53 3.05 2.56 2.06 4.61 3.75 3.31 2.86 2.40 1.94 5.44 4.61 3.75 3.31 2.86 2.40 1.94 3.50 3.09 2.67 2.25 1.81 3.25 2.87
2
wgt k=ft 27.20 23.60 20.00 16.20 14.30 12.30 10.30 19.80 16.80 13.60 12.00 10.40 8.70 7.00 15.70 12.80 11.30 9.80 8.20 6.60 18.50 15.70 12.80 11.30 9.80 8.20 6.60 11.90 10.60 9.10 7.70 6.20 11.10 9.80
Iy in 17.80 15.70 13.60 11.30 10.00 8.74 7.42 5.55 4.83 4.05 3.63 3.18 2.72 2.23 3.06 2.58 2.32 2.04 1.75 1.44 7.67 6.66 5.56 4.97 4.36 3.71 3.04 3.79 3.40 2.95 2.55 2.09 2.42 2.18
4
Sy in 5.17 4.53 3.86 3.16 2.79 2.42 2.04 2.22 1.90 1.56 1.39 1.21 1.02 0.83 1.39 1.15 1.02 0.89 0.75 0.61 2.81 2.40 1.97 1.75 1.52 1.29 1.05 1.52 1.35 1.16 0.99 0.81 1.12 0.99
3
Zx in 9.33 8.16 6.95 5.68 5.03 4.36 3.68 7.65 6.55 5.38 4.77 4.14 3.49 2.83 6.27 5.16 4.57 3.97 3.36 2.72 5.07 4.33 3.56 3.16 2.74 2.32 1.88 3.50 3.11 2.71 2.29 1.86 3.41 3.03
3
Zy in 9.33 8.16 6.95 5.68 5.03 4.36 3.68 4.10 3.47 2.83 2.49 2.16 1.82 1.47 2.61 2.11 1.86 1.60 1.35 1.09 5.07 4.33 3.56 3.16 2.74 2.32 1.88 2.73 2.42 2.11 1.78 1.44 2.03 1.79
3
Victor Saouma
Draft 3{16
Designation L 4.0x3.0x0.375 L 4.0x3.0x0.313 L 4.0x3.0x0.250 L 3.5x3.5x0.500 L 3.5x3.5x0.438 L 3.5x3.5x0.375 L 3.5x3.5x0.313 L 3.5x3.5x0.250 L 3.5x3.0x0.500 L 3.5x3.0x0.438 L 3.5x3.0x0.375 L 3.5x3.0x0.313 L 3.5x3.0x0.250 L 3.5x2.5x0.500 L 3.5x2.5x0.438 L 3.5x2.5x0.375 L 3.5x2.5x0.313 L 3.5x2.5x0.250 L 3.0x3.0x0.500 L 3.0x3.0x0.438 L 3.0x3.0x0.375 L 3.0x3.0x0.313 L 3.0x3.0x0.250 L 3.0x3.0x0.188 L 3.0x2.5x0.500 L 3.0x2.5x0.438 L 3.0x2.5x0.375 L 3.0x2.5x0.313 L 3.0x2.5x0.250 L 3.0x2.5x0.188 L 3.0x2.0x0.500 L 3.0x2.0x0.438 L 3.0x2.0x0.375 L 3.0x2.0x0.313 L 3.0x2.0x0.250 L 3.0x2.0x0.188 L 2.5x2.5x0.500 L 2.5x2.5x0.375 L 2.5x2.5x0.313 L 2.5x2.5x0.250 L 2.5x2.5x0.188 L 2.5x2.0x0.375 L 2.5x2.0x0.313 L 2.5x2.0x0.250 L 2.5x2.0x0.188 L 2.0x2.0x0.375 L 2.0x2.0x0.313 L 2.0x2.0x0.250 L 2.0x2.0x0.188 L 2.0x2.0x0.125 L 1.8x1.8x0.250 L 1.8x1.8x0.188 L 1.5x1.5x0.250 L 1.5x1.5x0.188 L 1.3x1.3x0.250 L 1.3x1.3x0.188 L 1.1x1.1x0.125 L 1.0x1.0x0.125
STRUCTURAL MATERIALS
A wgt Ix Sx in k=ft in in 2.48 8.50 4.0 1.5 2.09 7.20 3.4 1.2 1.69 5.80 2.8 1.0 3.25 11.10 3.6 1.5 2.87 9.80 3.3 1.3 2.48 8.50 2.9 1.1 2.09 7.20 2.5 1.0 1.69 5.80 2.0 0.8 3.00 10.20 3.5 1.5 2.65 9.10 3.1 1.3 2.30 7.90 2.7 1.1 1.93 6.60 2.3 1.0 1.56 5.40 1.9 0.8 2.75 9.40 3.2 1.4 2.43 8.30 2.9 1.3 2.11 7.20 2.6 1.1 1.78 6.10 2.2 0.9 1.44 4.90 1.8 0.8 2.75 9.40 2.2 1.1 2.43 8.30 2.0 1.0 2.11 7.20 1.8 0.8 1.78 6.10 1.5 0.7 1.44 4.90 1.2 0.6 1.09 3.71 1.0 0.4 2.50 8.50 2.1 1.0 2.21 7.60 1.9 0.9 1.92 6.60 1.7 0.8 1.62 5.60 1.4 0.7 1.31 4.50 1.2 0.6 1.00 3.39 0.9 0.4 2.25 7.70 1.9 1.0 2.00 6.80 1.7 0.9 1.73 5.90 1.5 0.8 1.46 5.00 1.3 0.7 1.19 4.10 1.1 0.5 0.90 3.07 0.8 0.4 2.25 7.70 1.2 0.7 1.73 5.90 1.0 0.6 1.46 5.00 0.8 0.5 1.19 4.10 0.7 0.4 0.90 3.07 0.5 0.3 1.55 5.30 0.9 0.5 1.31 4.50 0.8 0.5 1.06 3.62 0.7 0.4 0.81 2.75 0.5 0.3 1.36 4.70 0.5 0.4 1.15 3.92 0.4 0.3 0.94 3.19 0.3 0.2 0.71 2.44 0.3 0.2 0.48 1.65 0.2 0.1 0.81 2.77 0.2 0.2 0.62 2.12 0.2 0.1 0.69 2.34 0.1 0.1 0.53 1.80 0.1 0.1 0.56 1.92 0.1 0.1 0.43 1.48 0.1 0.1 0.27 0.90 0.0 0.0 0.23 0.80 0.0 0.0
2 4 3
Iy in 1.92 1.65 1.36 3.64 3.26 2.87 2.45 2.01 2.33 2.09 1.85 1.58 1.30 1.36 1.23 1.09 0.94 0.78 2.22 1.99 1.76 1.51 1.24 0.96 1.30 1.18 1.04 0.90 0.74 0.58 0.67 0.61 0.54 0.47 0.39 0.31 1.23 0.98 0.85 0.70 0.55 0.51 0.45 0.37 0.29 0.48 0.42 0.35 0.27 0.19 0.23 0.18 0.14 0.11 0.08 0.06 0.03 0.02
4
Sy in 0.87 0.73 0.60 1.49 1.32 1.15 0.98 0.79 1.10 0.98 0.85 0.72 0.59 0.76 0.68 0.59 0.50 0.41 1.07 0.95 0.83 0.71 0.58 0.44 0.74 0.66 0.58 0.49 0.40 0.31 0.47 0.42 0.37 0.32 0.26 0.20 0.72 0.57 0.48 0.39 0.30 0.36 0.31 0.25 0.20 0.35 0.30 0.25 0.19 0.13 0.23 0.14 0.13 0.10 0.09 0.07 0.04 0.03
3
Zx in 2.64 2.23 1.82 2.68 2.38 2.08 1.76 1.43 2.63 2.34 2.04 1.73 1.41 2.53 2.26 1.97 1.67 1.36 1.93 1.72 1.50 1.27 1.04 0.79 1.88 1.68 1.47 1.25 1.02 0.78 1.78 1.59 1.40 1.19 0.97 0.75 1.31 1.02 0.87 0.71 0.55 0.99 0.84 0.69 0.53 0.63 0.54 0.44 0.34 0.23 0.34 0.26 0.24 0.19 0.16 0.13 0.07 0.06
3
Zy in 1.56 1.31 1.06 2.68 2.38 2.08 1.76 1.43 1.98 1.76 1.53 1.30 1.05 1.40 1.24 1.07 0.91 0.74 1.93 1.72 1.50 1.27 1.04 0.79 1.35 1.20 1.05 0.89 0.72 0.55 0.89 0.79 0.68 0.58 0.47 0.36 1.31 1.02 0.87 0.71 0.55 0.66 0.56 0.46 0.35 0.63 0.54 0.44 0.34 0.23 0.34 0.26 0.24 0.19 0.16 0.13 0.07 0.06
3
Victor Saouma
3{17
43 Steel joists, Fig. 3.8 look like shallow trusses (warren type) and are designed as simply supported uniformly loaded beams assuming that they are laterally supported on the top (to prevent lateral torsional buckling). The lateral support is often pro ded by the concrete slab it suppors. 44 The standard open-web joist designation consists of the depth, the series designation and the chord type. Three series are available for oor/roof construction, Table 3.3
Figure 3.8: prefabricated Steel Joists Typical joist spacing ranges from 2 to 4 ft, and provides an e cient use of the corrugated steel deck which itself supports the concrete slab.
Victor Saouma
4" 4"
Span
Draft 3{18
46
STRUCTURAL MATERIALS
For preliminary estimates of the joist depth, a depth to span ratio of 24 can be assumed, therefore
d L=2
(3.5)
where d is in inches, and L in ft. 47 Table 3.4 list the load carrying capacity of open web, K-series steel joists based on a amximum allowable stress of 30 ksi. For each span, the rst line indicates the total safe uniformly distributed load-carrying capacity in pounds per linear foot. Note that the dead load (including the one of the joist) must be substracted in order to determine the safe live load. The second line indicates the live load (pounds/linear foot) which will produce an approximate delection of L=360.
Victor Saouma
3{19
550 550 550 510 550 463 543 428 476 351 420 291 374 245 335 207 302 177 273 153 249 132 227 116 208 101
550 550 550 510 550 463 550 434 550 396 550 366 507 317 454 269 409 230 370 198 337 172 308 150 282 132
550 550 511 475 448 390 395 324 352 272 315 230 284 197 257 170 234 147 214 128 196 113 180 100 166 88 154 79 143 70
550 550 550 507 550 467 495 404 441 339 395 287 356 246 322 212 293 184 268 160 245 141 226 124 209 110 193 98 180 88
550 550 550 507 550 467 550 443 530 397 475 336 428 287 388 248 353 215 322 188 295 165 272 145 251 129 233 115 216 103
550 550 550 507 550 467 550 443 550 408 550 383 525 347 475 299 432 259 395 226 362 199 334 175 308 56 285 139 265 124
550 550 512 488 456 409 408 347 368 297 333 255 303 222 277 194 254 170 234 150 216 133 200 119 186 106 173 95 161 86 151 78 142 71
550 550 550 526 508 456 455 386 410 330 371 285 337 247 308 216 283 189 260 167 240 148 223 132 207 118 193 106 180 96 168 87 158 79
550 550 550 526 550 490 547 452 493 386 447 333 406 289 371 252 340 221 313 195 289 173 268 155 249 138 232 124 216 112 203 101 190 92
550 550 550 526 550 490 550 455 550 426 503 373 458 323 418 282 384 248 353 219 326 194 302 173 281 155 261 139 244 126 228 114 214 103
550 550 550 526 550 490 550 455 550 426 548 405 498 351 455 307 418 269 384 238 355 211 329 188 306 168 285 151 266 137 249 124 233 112
550 550 550 526 550 490 550 455 550 426 550 406 550 385 507 339 465 298 428 263 395 233 366 208 340 186 317 167 296 151 277 137 259 124
550 550 550 526 550 490 550 455 550 426 550 406 550 385 550 363 550 346 514 311 474 276 439 246 408 220 380 198 355 178 332 161 311 147
Victor Saouma
Draft 3{20
STRUCTURAL MATERIALS
Victor Saouma
Draft
Chapter 4
Draft 4{2
2
The tower is 984 feet high, and 328 feet wide at the base. The large base was essential to provide adequate stability in the presence of wind load. 5 We can assume that the shape of the tower is parabolic. If we take the x axis to be along the vertical axis of symmetry and y the half width, then we know that at x = 984 the (half) width y = 0 and at x = 0 the half width is 328=2 = 164, thus the equation of the half width is given by
2
}
(4.1)
av(x)2
{z
;x = 984 2 952
Also
dy dv
dv dx
dy = tan ) = tan;1 dy dx dx where is the angle measured from the x axis to the tangent to the curve.
3
Victor Saouma
4{3
2.
An idealization
4.2 Loads
5 6
The total weight of the tower is 18 800 . The dead load is not uniformly distributed, and is approximated as follows, Fig. 4.3:
k
Location Height Dead Weight Ground- second platform 380 ft 15 500 Second platform-intermediate platform 264 ft 2 200 intermediate platform - top 340 ft 1 100 Total 984 ft 18 800
7
k k k
From the actual width of the lower two platforms we can estimate the live loads (the intermediate and top platforms would have negligible LL in comparison):
psf ft lbs lbs k k psf ft k
kip 1st platform: (50) (240)2 2 (1 000) 2 880 2 2 2nd platform: (50) (110) (1 000) 600 Total: 3 480 Hence the total vertical load is Pvert = DL + LL = 18 800 + 3 480 = 22 280 .
k k
Victor Saouma
Draft 4{4
Figure 4.3: Ei el Tower, Dead Load Idealization (Billington and Mark 1983)
8
4.3 Reactions
9
The wind pressure is known to also have a parabolic distribution (maximum at the top), the cross sectional area over which the wind is acting is also parabolic (maximum at the base). Hence we will simplify our analysis by considering an equivalent wind force obtained from a constant wind pressure (force/length) and constant cross section Fig. 4.4: The pressure is assumed to be 2.6 k/ft, thus the lateral wind force is, Fig. 4.5 (4.5) Plat = (2:6) (984) = 2,560 acting at 984 2 = 492
k/ft ft k ft
Simplifying the three dimensional structure with 4 supports into a two dimensional one with two supports, the reactions can be easily determined for this statically determinate structure, Fig.4.6. Gravity Load
(4.6-a) (4.6-b)
Lateral Load Lateral Moment (we essentially have a cantilivered beam subjected to a uniform load). The
moment at a distance x from the support along the cantilevered beam subjected to a uniform pressure p is given by L ; x = p (L ; x )2 (4.7) Mlat = p ( L ; x ) | {z } 2 } 2 | {z Force Moment arm
Victor Saouma
4{5
Figure 4.4: Ei el Tower, Wind Load Idealization (Billington and Mark 1983)
TOTAL LOADS
LOADS P
P=2560k
Q
L/2
Q=22,280k
1111 0000 0000 H 1111 0000 1111 000 0 111 0000 1111 000 111 000 111 000 111 V 0 000 111 000 111 000 111 000 111
REACTIONS M0
WINDWARD SIDE
LEEWARD SIDE
VERTICAL FORCES
WIND FORCES
TOTAL
Victor Saouma
Draft 4{6
k/ft
Thus the lateral moment caused by the wind is parabolic. At the base (x = 0), the maximum moment is equal to x)2 = (2:6) (984 ; 0)2 2 = 1,260,000 ; Mlat = p (L ; (4.8) 2 2 We observe that the shape of the moment diagram is also parabolic, just like the tower itself. This is not accidental, as nearly optimum structures have a shape which closely approximate their moment diagram (such as the varying depth of continuous long span bridges). To determine the resulting internal forces caused by the lateral (wind) moment, and since we have two supports (one under tension and the other under compression) we use 1 260 000 = 3,850 wind = Rvert = M (4.9) 6? d 328 Lateral Forces to be resisted by each of the two pairs. By symmetry, the lateral force will be equally divided among the two pairs of supports and will be equal to wind = 1,280 Rlat = (2 560) (4.10) 2
ft k.ft k.ft k ft k k
y = F F (4.11-b) x
x = F F (4.11-a)
Fy (4.11-c) = F
11
Internal forces are rst determined at the base. 12 Gravity load are rst considered, remember those are caused by the dead load and the live load, Fig. 4.7:
=18.40 =18.4
INCLINED INTERNAL FORCE: N CONSEQUENT HORIZONTAL COMPONENT: H N V
H FORCE POLYGON
Figure 4.7: Ei el Tower, Internal Gravity Forces (Billington and Mark 1983) cos
Victor Saouma
V )N= V = N cos
(4.12-a)
4{7
(4.12-b) (4.12-c) (4.12-d)
The horizontal forces which must be resisted by the foundations, Fig. 4.8.
H 3700 k
3700 k
Because the vertical load decreases with height, the axial force will also decrease with height. 14 At the second platform, the total vertical load is Q = 1 100 + 2 200 = 3 300 and at that height the angle is 11:6o thus the axial force (per pair of columns) will be
k
Note that this is about seven times smaller than the axial force at the base, which for a given axial strength, would lead the designer to reduce (or taper) the cross-section. The horizontal force will be resisted by the axial forces in the second platform itself. 15 Wind Load: We now have determined at each pair of support the vertical and the horizontal forces caused by the wind load, the next step is to determine their axial components along the inclined leg, Fig. 4.9:
wind wind Nc = ;Rvert cos ; Rlat sin o = ;(3 850) (cos 18:4 ) ; (1 280) (sin 18:40)
k k
3 300 k
(4.13-a)
k
(4.13-b)
= Nt = = =
Leeward wind ;R cos + Rlat sin o (3 850) (cos 18:4 ) + (1 280) (sin 18:40) 4,050 Winward
k
-4,050
wind vert
Victor Saouma
Draft 4{8
3,850 k 3,850 cos 18.4
18.4
18.4
1,280 k
Figure 4.9: Ei el Tower, Internal Wind Forces (Billington and Mark 1983)
The total forces caused by both lateral and gravity forces can now be determined: Total = ;(11 730) ;(4 050) = -15,780 Leeward side NL gravity lateral Total 050) } = -7,630 NW = ; (11{z 730) } +(4 | {z | gravity lateral
k k
{z
}|
{z
(4.15-a) (4.15-b)
Winward side
We observe that even under wind load, the windward side is still under compression. 2. 17 In the idealization of the tower's geometry, the area of each pair of the simpli ed columns is 1 600 and thus the maximum stresses will be determined from T ;15 780 NL = -9.9 (4.16) = comp = A 1 600 2
in k ksi in
18
The strength of wrought iron is 45 ksi, hence the safety factor is stress 45 Safety Factor = ultimate actual stress = 9:9 = 4.5
ksi ksi
(4.17)
Victor Saouma
Draft
Chapter 5
REVIEW of STATICS
To every action there is an equal and opposite reaction.
Newton's third law of motion
5.1 Reactions
1
In the analysis of structures (hand calculations), it is often easier (but not always necessary) to start by determining the reactions. 2 Once the reactions are determined, internal forces are determined next nally, internal stresses and/or deformations (de ections and rotations) are determined last1 . 3 Reactions are necessary to determine foundation load. 4 Depending on the type of structures, there can be di erent types of support conditions, Fig. 5.1. Roller: provides a restraint in only one direction in a 2D structure, in 3D structures a roller may provide restraint in one or two directions. A roller will allow rotation. Hinge: allows rotation but no displacements. Fixed Support: will prevent rotation and displacements in all directions.
5.1.1 Equilibrium
5 6 7
method, we determine displacements rsts, then internal forces and reactions. This method is most suitable to computer implementation. In a dynamic system F = ma where m is the mass and a is the acceleration.
2
Reactions are determined from the appropriate equations of static equilibrium. Summation of forces and moments, in a static system must be equal to zero2. In a 3D cartesian coordinate system there are a total of 6 independent equations of equilibrium: This is the sequence of operations in the exibility method which lends itself to hand calculation. In the sti ness
1
Draft 5{2
REVIEW of STATICS
Fx = Mx =
8
Fy = My =
Fz = 0 Mz = 0
(5.1)
Fx =
9
Fy =
Mz = 0
(5.2)
For reaction calculations, the externally applied load may be reduced to an equivalent force3 . 10 Summation of the moments can be taken with respect to any arbitrary point. 11 Whereas forces are represented by a vector, moments are also vectorial quantities and are represented by a curved arrow or a double arrow vector. 12 Not all equations are applicable to all structures, Table 5.1 13 The three conventional equations of equilibrium in 2D: Fx Fy and Mz can be replaced by the independent moment equations MzA, MzB , MzC provided that A, B, and C are not colinear. 14 It is always preferable to check calculations by another equation of equilibrium. 15 Before you write an equation of equilibrium, 1. Arbitrarily decide which is the +ve direction 2. Assume a direction for the unknown quantities 3. The right hand side of the equation should be zero
3
However for internal forces (shear and moment) we must use the actual load distribution.
Victor Saouma
5{3
Fx Fx MzA Fx MzA Fy Fy Fy MzB MzA MzB
Equations
Fz Fz MzB MzC Mx Mx My My
Mz Mz Mz
Alternate Set
Table 5.1: Equations of Equilibrium If your reaction is negative, then it will be in a direction opposite from the one assumed. 16 Summation of external forces is equal and opposite to the internal ones. Thus the net force/moment is equal to zero. 17 The external forces give rise to the (non-zero) shear and moment diagram.
Rx = Sy Ry Sx
(5.3)
Victor Saouma
Draft 5{4
22
REVIEW of STATICS
If the reactions can not be determined simply from the equations of static equilibrium (and equations of conditions if present), then the reactions of the structure are said to be statically indeterminate. 23 The degree of static indeterminacy is equal to the di erence between the number of reactions and the number of equations of equilibrium (plus the number of equations of conditions if applicable), Fig. 5.3.
Failure of one support in a statically determinate system results in the collapse of the structures. Thus a statically indeterminate structure is safer than a statically determinate one. 25 For statically indeterminate structures, reactions depend also on the material properties (e.g. Young's and/or shear modulus) and element cross sections (e.g. length, area, moment of inertia).
The stability of a structure is determined not only by the number of reactions but also by their arrangement. 27 Geometric instability will occur if: 1. All reactions are parallel and a non-parallel load is applied to the structure. 2. All reactions are concurrent, Fig. 5.4.
Victor Saouma
5{5
3. The number of reactions is smaller than the number of equations of equilibrium, that is a mechanism is present in the structure.
28 Mathematically, this can be shown if the determinant of the equations of equilibrium is equal to zero (or the equations are inter-dependent).
29 Examples of reaction calculation will be shown next. Each example has been carefully selected as it brings a di erent \twist" from the preceding one. Some of those same problems will be revisited later for the determination of the internal forces and/or de ections. Many of those problems are taken from Prof. Gerstle textbok Basic Structural Analysis.
Solution:
The beam has 3 reactions, we have 3 equations of static equilibrium, hence it is statically determinate. (+ - ) Fx = 0 ) Rax ; 36 = 0 (+ 6 ) Fy = 0 ) Ray + Rdy ; 60 ; (4) (12) = 0 (+ ;) Mzc = 0 ) 12Ray ; 6Rdy ; (60)(6) = 0
k k k/ft ft
1 0 0 0 1 1 0 12 ;6
38 < 5 :
9 =
=:
8 <
36 108 360
9 =
):
8 <
9 =
=:
8 <
36 56 52
k k k
9 =
Alternatively we could have used another set of equations: (+ ;) Mza = 0 (60)(6) + (48)(12) ; (Rdy )(18) = 0 ) Rdy = 52 d = 0 (Ray )(18) ; (60)(12) ; (48)(6) = 0 ) Ray = 56 (+ ;) Mz (+ 6 ) Fy = 0 56 ; 52 ; 60 ; 48 = 0
k k
Check:
6 6
Victor Saouma
Draft 5{6
Example 5-8: Three Span Beam
Determine the reactions of the following three spans beam
REVIEW of STATICS
Solution:
We have 4 unknowns (Rax Ray Rcy and Rdy ), three equations of equilibrium and one equation of condition ( Mb = 0), thus the structure is statically determinate. 1. Isolating ab: M ;b = 0 (9)(Ray ) ; (40)(5) = 0 ) Ray = 22.2 6 (+ ;) Ma = 0 (40)(4) ; (S )(9) = 0 ) S = 17.7 6 Fx = 0 ) Rax = 30
k k k
2. Isolating bd: (+ ;) Md = 0 ;(17:7)(18) ; (40)(15) ; (4)(8)(8) ; (30)(2) + Rcy (12) = 0 236 = 103 ) Rcy = 1 12 6 ; (+ ) Mc = 0 ;(17:7)(6) ; (40)(3) + (4)(8)(4) + (30)(10) ; Rdy (12) = 0 :3 ) Rdy = 201 12 = 16.7 6
k k
Victor Saouma
5{7
Fy = 0
Solution:
1. Due to symmetry, we will consider only the dead load on one side of the frame. 2. Due to symmetry, there is no vertical force transmitted by the hinge for snow and dead load. 3. Roof dead load per frame is p 1 302 + 152 1 000 DL = (20) (30) = 20:2 ?
psf ft ft lbs/k k
Victor Saouma
Draft 5{8
4. Snow load per frame is
REVIEW of STATICS
SL = (30)
1 (30) (30) 1 000
ft ft
psf
lbs/k
= 27:
?
k
WL = (15)
psf
lbs/k
= 15:75
6. There are 4 reactions, 3 equations of equilibrium and one equation of condition ) statically determinate. 7. The horizontal reaction H due to a vertical load V at midspan of the roof, is obtained by taking moment with respect to the hinge
V (+ ;) MC = 0 15(V ) ; 30(V ) + 35(H ) = 0 ) H = 15 35 = :429V
8. The reactions due to wind load are B (+ ;) MA = 0 (15:75)( 20+15 2 ) ; VWL (60) = 0 ; B (+ ) MC = 0 HWL (35) ; (4:6)(30) = 0 A =0 (+ - ) Fx = 0 15:75 ; 3:95 ; HWL B A (+ 6 ) Fy = 0 VWL ; VWL = 0 9. Thus supports should be designed for
k k
6
k k
= 24.19 = 52.3
5.2 Trusses
30
5.2.1 Assumptions
Cables and trusses are 2D or 3D structures composed of an assemblage of simple one dimensional components which transfer only axial forces along their axis. 31 Trusses are extensively used for bridges, long span roofs, electric tower, space structures. 32 For trusses, it is assumed that 1. Bars are pin-connected
Victor Saouma
5{9
A truss would typically be composed of triangular elements with the bars on the upper chord under compression and those along the lower chord under tension. Depending on the orientation of the diagonals, they can be under either tension or compression. 34 In a truss analysis or design, we seek to determine the internal force along each member, Fig. 5.5
Sign Convention: Tension positive, compression negative. On a truss the axial forces are indicated as
forces acting on the joints. Stress-Force: = P A Stress-Strain: = E" Force-Displacement: " = LL Equilibrium: F = 0
In practice the bars are riveted, bolted, or welded directly to each other or to gusset plates, thus the bars are not free to rotate and so-called secondary bending moments are developed at the bars. Another source of secondary moments is the dead weight of the element.
4
Victor Saouma
Draft 5{10
38
REVIEW of STATICS
Since each joint is pin-connected, we can apply M = 0 at each one of them. Furthermore, summation of forces applied on a joint must be equal to zero. 39 For a 2D truss we have 2 equations of equilibrium FX = 0 and FY = 0 which can be applied at each joint. For 3D trusses we would have three equations: FX = 0, FY = 0 and FZ = 0. 40 If we refer to j as the number of joints, R the number of reactions and m the number of members, then we would have a total of m + R unknowns and 2j (or 3j ) equations of statics (2D or 3D at each joint). If we do not have enough equations of statics then the problem is indeterminate, if we have too many equations then the truss is unstable, Table 5.2. External R>3 R>6 Internal m + R > 2j m + R > 3j Unstable m + R < 2j m + R < 3j Table 5.2: Static Determinacy and Stability of Trusses
Static Indeterminacy
2D
3D
41
Fig. 5.6 shows a truss with 4 reactions, thus it is externally indeterminate. This truss has 6 joints (j = 6), 4 reactions (R = 4) and 9 members (m = 9). Thus we have a total of m + R = 9 + 4 = 13 unknowns and 2 j = 2 6 = 12 equations of equilibrium, thus the truss is statically indeterminate.
There are two methods of analysis for statically determinate trusses 1. The Method of joints 2. The Method of sections
The method of joints can be summarized as follows 1. Determine if the structure is statically determinate
Victor Saouma
5{11
2. Compute all reactions 3. Sketch a free body diagram showing all joint loads (including reactions) 4. For each joint, and starting with the loaded ones, apply the appropriate equations of equilibrium ( Fx and Fy in 2D Fx , Fy and Fz in 3D).
~ =F ~x + F ~y ) must be 5. Because truss elements can only carry axial forces, the resultant force (F along the member, Fig. 5.7. F = Fx = Fy l lx ly
(5.4)
44 Always keep track of the x and y components of a member force (Fx , Fy ), as those might be needed later on when considering the force equilibrium at another joint to which the member is connected.
This method should be used when all member forces should be determined. 46 In truss analysis, there is no sign convention. A member is assumed to be under tension (or compression). If after analysis, the force is found to be negative, then this would imply that the wrong assumption was made, and that the member should have been under compression (or tension). 47 On a free body diagram, the internal forces are represented by arrow acting on the joints and not as end forces on the element itself. That is for tension, the arrow is pointing away from the joint, and for compression toward the joint, Fig. 5.8.
Victor Saouma
Draft 5{12
Example 5-10: Truss, Method of Joints
Using the method of joints, analyze the following truss
REVIEW of STATICS
Solution:
1. R = 3, m = 13, 2j = 16, and m + R = 2j 2. We compute the reactions
k
(+ ;) ME = 0 ) (20 + 12)(3)(24) + (40 + 8)(2)(24) + (40)(24) ; RAy (4)(24) = 0 ) RAy = 58 6 ) Fy = 0 ) 20 + 12 + 40 + 8 + 40 ; 58 ; REy = 0 (+ ? ) REy = 62 6
k
3. Consider each joint separately: Node A: Clearly AH is under compression, and AB under tension.
(+ 6 ) Fy = 0 ) FAHy ; 58 = 0 FAH = lly (FAHy ) p ly = 32 l = 322 + 242 = 40 Compression ) FAH = 40 32 (58) = 72:5 (+ - ) Fx = 0 ) ;FAHx + FAB = 0 24 FAB = llx y (FAHy ) = 32 (58) = 43:5 Tension
Victor Saouma
5{13
Node H:
(+ - ) Fx = 0 ) FAHx ; FHCx ; FHGx = 0 p 24 43:5 ; p2424 (I) 2 +322 (FHC ) ; 242 +102 (FHG ) = 0 ) Fy = 0 ) FAHy + FHCy ; 12 ; FHGy ; 20 = 0 (+ 6 p 10 58 + p2432 2 +322 (FHC ) ; 12 ; 242 +102 (FHG ) ; 20 = 0 (II) Solving for I and II we obtain
Node E:
Fy = 0 ) FEFy = 62 ) FEF = p2432 = 77:5 2 2 (62) 24 (F+32 Fx = 0 ) FED = FEFx ) FED = 32 (62) = 46:5 EFy ) = 24 32
The results of this analysis are summarized below
k k
Victor Saouma
Draft 5{14
REVIEW of STATICS
4. We could check our calculations by verifying equilibrium of forces at a node not previously used, such as D
Later on, in more advanced analysis courses we will use a di erent one.
Victor Saouma
5{15
positive upward. Axial: tension positive. Flexure A positive moment is one which causes tension in the lower bers, and compression in the upper ones. For frame members, a positive moment is one which causes tension along the inner side. Shear A positive shear force is one which is \up" on a negative face, or \down" on a positive one. Alternatively, a pair of positive shear forces will cause clockwise rotation. Torsion Counterclockwise Draftpositive 3D: Use double arrow vectors (and NOT curved arrows). Forces and moments (including torsions) are x M 6 de ned with respect to a right hand side coordinate system, Fig. 5.10. * 6
y
Load Positive along the beam's local y axis (assuming a right hand side convention), that is
6 My 6 6 > -- z
z
** Tx -Mz
Figure 5.11: Free Body Diagram of an In nitesimal Beam Segment be in equilibrium. 51 There are no axial forces, thus we only have two equations of equilibrium to satisfy Fy = 0 and Mz = 0. 52 Since dx is in nitesimally small, the small variation in load along it can be neglected, therefore we assume w(x) to be constant along dx. 53 To denote that a small change in shear and moment occurs over the length dx of the element, we add the di erential quantities dVx and dMx to Vx and Mx on the right face.
6
In this derivation, as in all other ones we should assume all quantities to be positive.
Victor Saouma
Draft 5{16
54
REVIEW of STATICS
or
dV = w(x) dx
(5.5)
The slope of the shear curve at any point along the axis of a member is given by the load curve at that point.
(+ ;) Mo = 0 ) Mx + Vx dx ; wx dx dx 2 ; (Mx + dMx ) = 0 Neglecting the dx2 term, this simpli es to
55
Similarly
dM = V (x) dx
(5.6)
The slope of the moment curve at any point along the axis of a member is given by the shear at that point.
56
V =
w(x)dx
x2 x1
(5.7)
w(x)dx (5.8)
The change in shear between 1 and 2, V21 , is equal to the area under the load between x1 and x2 .
and
M =
V (x)dx
M21 = M2 ; M1 =
x2 x1
(5.9)
V (x)dx (5.10)
The change in moment between 1 and 2, M21, is equal to the area under the shear curve between x1 and x2 .
Note that we still need to have V1 and M1 in order to obtain V2 and M2 respectively. 58 Fig. 5.12 and 5.13 further illustrates the variation in internal shear and moment under uniform and concentrated forces/moment.
57
Victor Saouma
5{17
Figure 5.12: Shear and Moment Forces at Di erent Sections of a Loaded Beam
Positive Constant
Negative Constant
Load
Shear
Positive Constant
Negative Constant
Shear
Moment
Figure 5.13: Slope Relations Between Load Intensity and Shear, or Between Shear and Moment
Victor Saouma
Draft 5{18
5.3.1.4 Examples Example 5-11: Simple Shear and Moment Diagram
Draw the shear and moment diagram for the beam shown below
REVIEW of STATICS
Solution:
Victor Saouma
5{19
Moment
1. 2. 3.
5.
Draft 5{20
REVIEW of STATICS
Victor Saouma
5{21
) (+ ;) MA = 0 ) ) (+ 6 ) Fy = 0 ) )
RAx = 36
load
k
3 9 4 12 (3)(30)( 30 2 ) + 5 (3)(15) 30 + 2 ; 5 (3)(15) 2 ; 39RDy = 0 RFy = 52:96 RAy ; (3)(30) ; 3 5 (3)(15) + 52:96 = 0 RAy = 64:06
k k
Shear:
1. For A ; B , the shear is constant, equal to the horizontal reaction at A and negative according to our previously de ned sign convention, VA = ;36 2. For member B ; C at B , the shear must be equal to the vertical force which was transmitted along A ; B , and which is equal to the vertical reaction at A, VB = 64:06. 3. Since B ; C is subjected to a uniform negative load, the shear along B ; C will have a slope equal to ;3 and in terms of x (measured from B to C ) is equal to VB;C (x) = 64:06 ; 3x
k
4. The shear along C ; D is obtained by decomposing the vertical reaction at D into axial and 3 52:96 = 31:78 and is negative. Based shear components. Thus at D the shear is equal to 5 on our sign convention for the load, the slope of the shear must be equal to ;3 along C ; D. Thus the shear at point C is such that Vc ; 5 3 9(3) = ;31:78 or Vc = 13:22. The equation for the shear is given by (for x going from C to D) V = 13:22 ; 3x
k
Moment:
5. We check our calculations by verifying equilibrium of node C 3 (42:37) + 4 (13:22) = 25:42 + 10:58 = 36p (+ ) Fx = 0 ) 5 5 p 4 (42:37) ; 3 (+ 6 ) Fy = 0 ) 5 5 (13:22) = 33:90 ; 7:93 = 25:97 1. Along A ; B , the moment is zero at A (since we have a hinge), and its slope is equal to the shear, thus at B the moment is equal to (;36)(12) = ;432 2. Along B ; C , the moment is equal to
k.ft
VB;C (x)dx = ;432 + (64:06 ; 3x)dx 0 0 2 = ;432 + 64:06x ; 3 x2 which is a parabola. Substituting for x = 30, we obtain at node C : MC = ;432+64:06(30) ; 2 30 3 2 = 139:8 B;C = 0 at the 3. If we need to determine the maximum moment along B ; C , we know that dMdx 64 : 06 point where VB;C = 0, that is VB;C (x) = 64:06 ; 3x = 0 ) x = 3 = 25:0 . In other MB;C = MB +
k.ft
words, maximum moment occurs where the shear is zero. max = ;432 + 64:06(25:0) ; 3 (25:0)2 = ;432 + 1 601:5 ; 937:5 = 232 Thus MB ;C 2
ft
k.ft
Victor Saouma
Draft 5{22
REVIEW of STATICS
4. Finally along C ; D, the moment varies quadratically (since we had a linear shear), the moment rst increases (positive shear), and then decreases (negative shear). The moment along C ; D is given by R Rx MC ;D = MC + 0x VC ;D (x)dx = 139 : 8 + 0 (13:22 ; 3x)dx 2 x = 139:8 + 13:22x ; 3 2 which is a parabola. 2 Substituting for x = 15, we obtain at node C MC = 139:8 + 13:22(15) ; 3 15 2 = 139:8 + p 198:3 ; 337:5 = 0
Solution:
The hydrostatic pressure causes lateral forces on the vertical members which can be treated as cantilevers xed at the lower end. The pressure is linear and is given by p = h. Since each frame supports a 2 ft wide slice of the ume, the equation for w (pounds/foot) is w = (2)(62:4)(h) = 124:8h At the base w = (124:8)(6) = 749 = :749 Note that this is both the lateral pressure on the end walls as well as the uniform load on the horizontal members.
lbs/ft lbs/ft k/ft
Victor Saouma
5{23
6 = 2:246 1. Base force at B is FBx = (:749) 2 6 = 4:493 2. Base moment at B is MB = (2:246) 3 3. End force at B for member B ; E are equal and opposite. 4. Reaction at C is RCy = (:749) 16 2 = 5:99 Shear forces 1. Base at B the shear force was determined earlier and was equal to 2:246 . Based on the orientation of the x ; y axis, this is a negative shear. 2. The vertical shear at B is zero (neglecting the weight of A ; B ) 3. The shear to the left of C is V = 0 + (;:749)(3) = ;2:246 . 4. The shear to the right of C is V = ;2:246 + 5:99 = 3:744 Moment diagrams
k k.ft k k k k
End Actions
Victor Saouma
Draft 5{24
k.ft k.ft
REVIEW of STATICS
1. At the base: B M = 4:493 as determined above. 3 ) = ;7:864 2. At the support C , Mc = ;4:493 + (;:749)(3)( 2 5 ) = 1:50 3. The maximum moment is equal to Mmax = ;7:864 + (:749)(5)( 2 Design: Reinforcement should be placed along the bers which are under tension, that is on the side of the negative moment7 . The gure below schematically illustrates the location of the exural8 reinforcement.
k.ft
Victor Saouma
5{25
12 10 2k/ft 10k C V ba V bc
bd M ba H
M bc M bd 30k 0
HD
650k 450k
200k 82.5k
CHECK
10k
B Vba
Hba M ba
Hbc M bc Vbc
(10)+(2)(10) 30k
-22.5k
17.5-(5)(8)
M bc -200k
(10)(10)+(2)(10)(10)/2
-22.5+(-30)
Vba
(17.5)(3.5)/2 (17.5)(3.5)/2+(-22.5)(8-3.5)/2
(-52.5)(12)+(-20)
-650k
M ba
V bd 450k
(50)-(4)(15)/2
M bd Hbd
20k
450k
(50)(15)-[(4)(5)/2][(2)(15)/3)]
20k
50k
4k/ft
50k 82.5k
Victor Saouma
Draft 5{26
Example 5-15: Shear Moment Diagrams for Inclined Frame
REVIEW of STATICS
Victor Saouma
5{27
10 C 10 20k
26k 13 13
13 5 12
3 4
15 D
Ha 36 20
E Ve
19.2k
(20)(20)+(60-20)(20)/2
48.8k
60-(2)(20)
Fy
800k
20k
800k 0k
20k
2k/ft
60k 60k
19.2k
3
1k
48.8k
17.2 8k 12k
16k
6
(20)(15)/13=7.7
(20)(12)/(13)=18.46 (19.2)(5)/(13)=7.38 (19.2)(12)/(13)=17.72 (26)(12)/(13)=24 (26.6)(13)/(12)=28.8 (26.6)(5)/(12)=11.1 (28.8)(4)/(5)=23.1 (28.8)(3)/(5)=17.28 (20)(4)/(5)=16 (20)(3)/(5)=12 (39.1)(5)/(4)=48.9 (39.1)(3)/(4)=29.3
24k
24k
10k
20-10-10
800k
26.6k 8k
11.1k
778k 0k
20k
26k
10k
0k
23.
26k
778k
28.8k
17.72k
18.46k 7.38k
20k
28.8k
0k
39.1k 29.3k
19.2k
8.7 17.7+ .4k
48.9k
10
-23
+25
.1k -2 39
3.1
8 B-C
1,122-(26.6)(13) 488+(23.1)(12.5)
-16 k
.1
11 C-D
777
777k
k
(39.1)(12.5)
1130
488k
12 C-D
800k
13
9 B-C
14
+25.4
+20k
-23 .1 k k k 8 6 . 5 . 6 0 2 -39 .
0k 113
1k
112
2k
777k
48 8 k
800k
Victor Saouma
+60k
Draft 5{28
5.3.2 Formulaes
Adapted from (of Steel COnstruction 1986)
REVIEW of STATICS
Victor Saouma
5{29
w L R
L / 2 L / 2
Shear
M max.
R Vx
Moment
= = =
Victor Saouma
Draft 5{30
4) Simple Beam Uniform Load Partially Distributed
Max when a < c Max when a > c when a < x < a + b when x < a when a < x < a + b when a + b < x 1 at x = a + R w
REVIEW of STATICS
R1 = V1 R2 = V2 Vx Mx Mx Mx Mmax
= = = = = = =
R1 x 2 R1 x ; w 2 (x ; a) R2 (L ; x) R1 R1 a + 2 w
R1 = V1 R2 = V2 Mmax Mx
a x max
at x =
Pb L Pa L Pab L Pbx L2 2 Pa b = 3EIL 2 b2 ; x2 ) = 6Pbx EIL (L ; p Pab(a + 2b) 3a(a + 2b) = 27EIL
= = = =
Victor Saouma
5{31
R=V = P Mmax = Pa Pa max = 24EI (3L2 ; 4a2 ) Px (3La ; 3a2 ; x2 ) when x < a = 6 x EI Pa when a < x < L ; a = 6EI (3Lx ; 3x2 ; a2 ) x
max when a < b max when b < a when a < x < L ; b max when b < a max when a < b when x < a when a < x < L ; b
R1 = V1 R2 = V2 Vx M1 M2 Mx Mx
= = = = = = =
P ( L ; a + b) L P ( L ; b + a) L P (b ; a) L R1 a R2 b R1 x R1 x ; P (x ; a)
= = = = =
R1 ; wx wL2
8 9 2 128 wL
2
3 wL 8 5 wL 8
at x = :4215L
max
Victor Saouma
Draft 5{32
10) Propped Cantilever, Concentrated Load at Center
R1 = V1 R2 = V2 at x = L Mmax when x < L 2 Mx when L 2 < x Mx
at x = :4472L
max
REVIEW of STATICS
= = = =
11x = P L 2 ; 16 3 = :009317 PL EI
2L+a
max
Pb2 (a + 2L) 2 L3 Pa 2 2 2L3 (3L ; a ) R1 a Pab (a + L) 2L2 2 3 Pa b (3L + a) = 12 EIL32 2 3 (L ; a ) Pa = 3EI (3 L2 ; a2 )2 2r a Pab = 6EI 2L + a2
= = = =
Victor Saouma
5{33
R=V Vx at x = L Mmax Mx
x
at x = 0
max
R=V Vx Mx at x = L Mmax
x
at x = 0
= wL = wx 2 = wx 22 wL = 2 4 3 4 = 24w EI (x ; 4L x + 3L )
4 = wL 8EI
max
Victor Saouma
Draft 5{34
16) Cantilever Beam Point Load
R=V at x = L Mmax when a < x Mx at x = 0 max
at x = a when x < a when a < x
a x x
REVIEW of STATICS
Victor Saouma
5{35
Max when a < b R1 = V1 = Pb L Pa Max when b < a R2 = V2 = L at x < aL Mx = Pbx L p q Pab (a + 2b) 3a(a + 2b) a ( a +2 b ) when a > b = at x = max 3 2 b2 27EIL Pa at x = a = 3EIL a 2 2 2 when x < a = 6Pbx x EIL (L ; b ; x ) (L ; x) (2Lx ; x2 ; a2 ) when a < x = Pa x 6 EIL Pabx 1 at L < x < L + a = x1 6EIL (L + a)
R1 = V1 R2 = V2 + V3 R3 = V3 V2 Mmax at x = L M1
= = = = = =
Victor Saouma
Draft 5{36
22) Simple Beam, Uniform Load, End Moments
REVIEW of STATICS
M2 R1 = V1 = wL + M1 ; 2 L M1 ; M2 R2 = V2 = wL 2 ; L M1 ; M2 Vx = w L 2 ;x + L M1 ;M2 at x = L 2 + wL M1 ; M2 x ; M Mx = wx ( L ; x ) + 1 2 L
s
b
x
Victor Saouma
5{37
w (L2 ; a2 ) 2 L w 2 2L (L + a) wa w (L2 + a2 ) 2L R1 ; wx w(a ; x1 ) w (L + a)2 (L ; a)2 8L2 2 = wa 2 = wx (L2 ; a2 ; xL) 2 L = w (a ; x )2
2
1
at 0 < x < L at L < x < L + a a2 at x = L 2 1 ; L2 at 0 < x < L at L < x < L + a at 0 < x < L at L < x < L + a
x x1
at x = L
at 0 < x < L at L < x < L + a a2 at x = L 2 1 ; L2 at 0 < x < L at L < x < L + a at 0 < x < L at L < x < L + a at x = L
R1 = V1 R2 = V2 + V3 V2 V3 Vx Vx1 M1 M2 = Mx = Mx1 =
x x1
= = = = = = = = =
= =
5.4 Flexure
61
wx (L4 ; 2L2x2 + Lx3 ; 2a2 L2 + 2a2 x2 ) 24 EIL wx 1 (4a2 L; L3 + 6a2 x ; 4ax2 + x3 ) 1 1 1 24 EI w (L2 ; a2 ) 2 L w 2 2 L ( L + a) wa w (L2 + a2 ) 2L R1 ; wx w(a ; x1 ) w (L + a)2 (L ; a)2 8L2 wa2 2 wx (L2 ; a2 ; xL) 2 L w (a ; x )2 2 wx 1 (L4 ; 2L2x2 + Lx3 ; 2a2 L2 + 2a2 x2 ) 24 EIL wx1 (4a2 L; L3 + 6a2x ; 4ax2 + x3 ) 1 1 1 24EI
Victor Saouma
Draft 5{38
O +ve Curvature, +ve bending d -ve Curvature, -ve Bending
REVIEW of STATICS
M M
Neutral Axis E F Y dA E F X Z
dx
d = dx E 0 F 0 = ( ; y)d = d ; yd = dx ; y dx
(5.12)
0 F 0 ; EF dx ; y dx ; dx E "x = EF = dx
(5.14) (5.15)
"x = ; y
where y is measured from the axis of rotation (neutral axis). Thus strains are proportional to the distance from the neutral axis. 64 (Greek letter rho) is the radius of curvature. In some textbook, the curvature (Greek letter kappa) is also used where =1 (5.16) thus,
"x = ; y
(5.17)
Victor Saouma
5{39
65 So far we considered the kinematic of the beam, yet later on we will need to consider equilibrium in terms of the stresses. Hence we need to relate strain to stress. 66 For linear elastic material Hooke's law states
x = E"x
(5.18)
(5.19)
Just as external forces acting on a structure must be in equilibrium, the internal forces must also satisfy the equilibrium equations. 69 The internal forces are determined by slicing the beam. The internal forces on the \cut" section must be in equilibrium with the external forces.
5.4.3.1
70
Fx = 0 Neutral Axis
The rst equation we consider is the summation of axial forces. 71 Since there are no external axial forces (unlike a column or a beam-column), the internal axial forces must be in equilibrium. Z Fx = 0 ) (5.20) x dA = 0 where x was given by Eq. 5.19, substituting we obtain
Z
But since the curvature and the modulus of elasticity E are constants, we conclude that
Z
x dA = ;
E ydA = 0
(5.21-a)
ydA = 0
(5.22)
neutral axis passes through the centroid of the cross section. 5.4.3.2
72
or the rst moment of the cross section with respect to the z axis is zero. Hence we conclude that the
M = 0 Moment of Inertia
The second equation of internal equilibrium which must be satis ed is the summation of moments. However contrarily to the summation of axial forces, we now have an external moment to account for,
Victor Saouma
Draft 5{40
Mz = 0 ;+ve |{z} M =;
Ext.
| Z
REVIEW of STATICS
x ydA A{z }
the one from the moment diagram at that particular location where the beam was sliced, hence (5.23) Int. where dA is an di erential area a distance y from the neutral axis. 73 Substituting Eq. 5.19 9 Z Z = M = ; x ydA M = E y 2 dA A A x = ;E y
74
(5.24)
We now pause and de ne the section moment of inertia with respect to the z axis as
I def =
and section modulus as
y2 dA
(5.25) (5.26)
S def = I c
75
We now have the ingredients in place to derive one of the most important equations in structures, the beam formula. This formula will be extensively used for design of structural components. 77 We merely substitute Eq. 5.25 into 5.24,
M = I =
which shows that the curvature of the longitudinal axis of a beam is proportional to the bending moment M and inversely proportional to EI which we call exural rigidity. 78 Finally, inserting Eq. 5.19 above, we obtain x = ;E y (5.28) x = ; My M I = EI Hence, for a positive y (above neutral axis), and a positive moment, we will have compressive stresses above the neutral axis. 79 Alternatively, the maximum ber stresses can be obtained by combining the preceding equation with Equation 5.26
x=;S
y2 dA
y2 dA
9 > = >
M 1 EI = =
(5.27)
(5.29)
Example 5-16: Design Example Victor Saouma Structural Concepts and Systems for Architects
5{41
h y b
Y a
A x y Ix Iy
= = = = =
bh
b 2 h 2 bh3 12 hb3
12
h h y b b
A x y Ix Iy
= = = = =
bh ; b0 h0
2 h 2
c Y x
h y b
h y b
Y
A x y Ix Iy
= = = = =
bh b2 +c h3 3 bh3 36 2 bh (b ; bc + c2 )
36
r X
A = Ix = Iy =
d r 4 = 64
d2 r42 = 4 4
A = 2 rt = dt 3t Ix = Iy = r3 t = d 8
b X b a a
A = Ix = Iy =
ab3
4
ab 3 ba3
Victor Saouma
Draft 5{42
in ksi
REVIEW of STATICS
A 20 ft long, uniformly loaded, beam is simply supported at one end, and rigidly connected at the other. The beam is composed of a steel tube with thickness t = 0:25 . Select the radius such that max 18 , and max L=360.
1 k/ft r 20 0.25
Solution:
wL 3 1. Steel has E = 29 000 , and from above Mmax = wL 8 , max = 185EI , and I = r t. 2. The maximum moment will be 2 (1) (20)2 2 = 50 Mmax = wL = 8 8
ksi
k/ft
ft
k.ft
(5.30)
I =
rt
= = =
9 =
wL4
(5.31)
rt
in/ft in
(5.32)
in/ft
764 ) r =
:65 ) r = = 0:67 = 65 r3
in
r
3
764 = 6.51 18
in
(5.33-a) (5.33-b)
in
Victor Saouma
5{43
1. A positive and negative moment would correspond to positive and negative curvature respectively (adopting the sign convention shown in Fig. 5.14). 2. A zero moment correspnds to an in ection point in the de ected shape.
Statically determinate structure, we can determine the de ected shape from the moment diagram,
Fig. 5.15.
Hence, for
Victor Saouma
Draft 5{44
REVIEW of STATICS
Victor Saouma
5{45
Perform an approximate analysis of the following beam, and compare your results with the exact solution.
20k 16 12 28 28
Solution:
20k 16 12 28 28
22
28
1. We have 3 unknowns RA , RC , and RD , all in the vertical directions, and only two applicable equations of equilibrium (since we do not have any force in the x direction), thus the problem is statically indeterminare. 2. We sketch the anticipated de ected shape, and guess the location of the in ection point. 3. At that location, we place a hinge, and we now have an additional equation of condition at that location ( M = 0).
Victor Saouma
Draft 5{46
4. If we consider AB, and take the moments with respect to point B: 5. If we now consider the entire beam:
REVIEW of STATICS
(+ ;) MB = 0 (22)(RA ) ; (20)(22 ; 16) = 0 ) RA = 5.45
(5.34-a)
(+ ;) MD = 0 (RA )(28 + 28) ; (20)(28 + 12) + (RC )(28) = 0 (5:45)(56) ; (20)(40) + (RC )(28) = 0 ) RC = 17.67 6 (+ 6 ) Fy = 0 RA ; 20 + Rc + RD = 0 5:45 ; 20 + 17:67 + RD = 0 ) RD = ;3:12 3.12 ?
k k
6. Check (+ ;) MA = 0 (20)(16) ; (RC )(28) + (RD )(28 + 28) = 320 ; (17:67)(28) + (3:12)(56) = p 320 ; 494:76 + 174:72 = 0 7. The moments are determined next (5.36-a) (5.37-a) (5.37-b)
8. We now compare with the exact solution from Section 5.3.2, solution 21 where:L = 28, a = 16, b = 12, and P = 20
2 = (20)(12) 4(28)3 4(28) ; (16)(28 + 16) = 6.64 Pa 2L2 + b(L + a) R2 = RB = 2 L3 (20)(16) = 2(28)3 2(28)2 + 12(28 + 16) = 15.28 R3 = RD = ; Pab 4L3 (L + a) = ; (20)(16)(12) 4(28)3 (28 + 16) = ;1.92 Mmax = R1 a = (6:64)(16) = 106.2 M1 = R3 L = (1:92)(28) = 53.8
Pb 4L2 ; a(L + a) R1 = RA = 4 L3
Victor Saouma
5{47
Value Approximate Exact % Error RA 5.45 6.64 18 RC 17.67 15.28 -16 RD 3.12 1.92 63 M1 87.36 53.8 62 Mmax 87.2 106.2 18 10. Whereas the correlation between the approximate and exact results is quite poor, one should not underestimate the simplicity of this method keeping in mind (an exact analysis of this structure would have been computationally much more involved). Furthermore, often one only needs a rough order of magnitude of the moments.
Victor Saouma
Draft 5{48
REVIEW of STATICS
Victor Saouma
Draft
Chapter 6
Whereas the forces in a cable can be determined from statics alone, its con guration must be derived from its deformation. Let us consider a cable with distributed load p(x) per unit horizontal projection of the cable length (thus neglecting the weight of the cable). An in nitesimal portion of that cable can be assumed to be a straight line, Fig. 6.1 and in the absence of any horizontal load we have
T
V
V w dv dx V+dV H T+dT
H
H v x w(x) v(x)
ds
dx L
H =constant. Summation of the vertical forces yields (+ ? ) Fy = 0 ) ;V + wdx + (V + dV ) = 0 (6.1-a) dV + wdx = 0 (6.1-b) where V is the vertical component of the cable tension at x (Note that if the cable was subjected to its own weight then we would have wds instead of wdx). Because the cable must be tangent to T , we have V tan = H (6.2) d (H tan ) = w d(H tan ) + wdx = 0 ) ; dx
(6.3)
Draft 6{2
2 3
But H is constant (no horizontal load is applied), thus, this last equation can be rewritten as
dv which when substituted in Eq. 6.4 yields Written in terms of the vertical displacement v, tan = dx the governing equation for cables ;Hv00 = w (6.5)
4 For a cable subjected to a uniform load w , we can determine its shape by double integration of Eq. 6.5
and the constants of integrations C1 and C2 can be obtained from the boundary conditions: v = 0 at x = 0 and at x = L ) C2 = 0 and C1 = ; wL 2 . Thus v = 2w (6.7) H x(L ; x) This equation gives the shape v(x) in terms of the horizontal force H , L ) we can solve for the horizontal force 5 Since the maximum sag h occurs at midspan (x = 2
;Hv0 = wx + C1 2 ;Hv = wx 2 + C1 x + C2
(6.6-a) (6.6-b)
H = wL 8h
(6.8)
we note the analogy with the maximum moment in a simply supported uniformly loaded beam M = 2 . Furthermore, this relation clearly shows that the horizontal force is inversely proportional Hh = wL 8 to the sag h, as h & H %. Finally, we can rewrite this equation as
h r def = L wL = 8r H
6
(6.9-a) (6.9-b)
x2 + x v = 4h ; L 2 L
(6.10)
Thus the cable assumes a parabolic shape (as the moment diagram of the applied load). 7 Whereas the horizontal force H is constant throughout the cable, the tension T is not. The maximum tension occurs at the support where the vertical component is equal to V = wL 2 and the horizontal one to H , thus s s 2 2 p wL 2 = H 1 + wL=2 Tmax = V 2 + H 2 = + H (6.11) 2 H
Victor Saouma
6{3
(6.12)
Had we assumed a uniform load w per length of cable (rather than horizontal projection), the equation would have been one of a catenary2.
w L v=H w cosh H 2 ; x
+h
(6.13)
The George Washington bridge, is a suspension bridge spanning the Hudson river from New York City to New Jersey. It was completed in 1931 with a central span of 3,500 ft (at the time the world's longest span). The bridge was designed by O.H. Amman, who had emigrated from Switzerland. In 1962 the deck was sti ened with the addition of a lower deck.
6.2.1 Geometry
A longitudinal and plan elevation of the bridge is shown in For simplicity we will assume in our analysis that the two approaching spans are equal to 650 ft. 11 There are two cables of three feet diameter on each side of the bridge. The centers of each pair are 9 ft apart, and the pairs themselves are 106 ft apart. We will assume a span width of 100 ft. 12 The cables are idealized as supported by rollers at the top of the towers, hence the horizontal components of the forces in each side of the cable must be equal (their vertical components will add up). 13 The cables support the road deck which is hungby suspenders attached at the cables. The cables are made of 26,474 steel wires, each 0.196 inch in diameter. They are continuous over the tower supports and are rmly anchored in both banks by huge blocks of concrete, the anchors. I 14 Because the cables are much longer than they are thick (large L ), they can be idealized a perfectly exible members with no shear/bending resistance but with high axial strength. 15 The towers are 578 ft tall and rest on concrete caissons in the river. Because of our assumption regarding the roller support for the cables, the towers will be subjected only to axial forces.
10
6.2.2 Loads
16
The dead load is composed of the weight of the deck and the cables and is estimated at 390 and 400 psf respectively for the central and side spans respectively. Assuming an average width of 100 ft, this
1 1 ( 1) 2 2 ( 1)b
Recalling that (a + b)n = an + nan; b + n n; an; b + or (1 + b)n = 1 + nb + n n; p 2 Thus for b << 1, 1 + b = (1 + b) 1 1+ b Derivation of this equation is beyond the scope of this course.
2! 2 2 2
2!
+ n n;
(
1)(n 3!
2)b
Victor Saouma
Draft 6{4
??
377 ft 327 ft
610 ft
3,500 ft 4,760 ft
650 ft
ELEVATION
N.J.
HUDSON RIVER
N.Y.
PLAN
Figure 6.2: Longitudinal and Plan Elevation of the George Washington Bridge
Victor Saouma
6{5
DL = (390) (100) (1 000)
k psf ft
lbs
= 39
k/ft
(6.14)
for the main span and 40 for the side ones. 17 For highway bridges, design loads are given by the AASHTO (Association of American State Highway Transportation O cials). The HS-20 truck is often used for the design of bridges on main highways, Fig. 6.3. Either the design truck with speci ed axle loads and spacing must be used or the equivalent uniform load and concentrated load. This loading must be placed such that maximum stresses are produced.
k/ft
k/ft
k/ft
(6.15)
We do not consider earthquake, or wind loads in this analysis. 19 Final DL and LL are, Fig. 6.4: TL = 39 + 8 = 47
k/ft
The thrust H (which is the horizontal component of the cable force) is determined from Eq. 6.8
2 cs H = wL 8h
ft
Victor Saouma
Draft 6{6
w D,S = 40 k/ft
w D = 39 k/ft
w D,S = 40 k/ft
DEAD LOADS
w L = 8 k/ft
Victor Saouma
6{7
h = 327 = 0:0934 Lcs p 3 500
k k k
H 1 + 16 r2 p
6.2.4 Reactions
21
The vertical force in the columns due to the central span (cs) is simply the support reaction, 6.6
wTOT = 39 + 8 = 47 k/ft A POINT OF NO MOMENT B REACTIONS AT TOP OF TOWER
L = 3,500 FT
Figure 6.6: Vertical Reactions in Columns Due to Central Span Load 1 wL = 1 (47) Vcs = 2 cs 2
2 2
k/ft
(3 500) = 82 250
ft
2
(6.16)
(6.17)
Note that we can check this by determining the vector sum of H and V which should be equal to Tmax : p p Vcs + H = (82 250) + (220 000) = 235 000 kp
2
23
Victor Saouma
Along the side spans (ss), the total load is TL = 40 + 8 = 48 . We determine the vertical reaction by taking the summation of moments with respect to the anchor: ss ; Vss Lss = 0 (6.18-a) MD = 0 ;+ hssH + (wss Lss) L2
k/ft
Draft 6{8
k k
(6.18-b) (6.18-c)
24
Hence the total axial force applied on the column is V = Vcs + Vss = (82 250) + (143 200) = 225,450
k k
(6.19)
25
The vertical reaction at the anchor is given by summation of the forces in the y direction, Fig. 6.7: ) Fy = 0 (wss Lss) + Vss + Ranchor = 0 (6.20-a) (+ 6 ;(48) (650) + (143 200) + Ranchor = 0 (6.20-b) Ranchor = 112,000 ? (6.20-c) (6.20-d)
k/ft ft k k
225,450 k 220,000 k
112,000 k
The axial force in the side cable is determined the vector sum of the horizontal and vertical reactions. q p ss 2 Tanchor = Ranchor + H 2 = (112 000)2 + (220 000)2 = 247 000 (6.21-a) q p ss 2 + H 2 = (143 200)2 + (220 000)2 = 262,500 Ttower = Vss (6.21-b)
k k
27
Victor Saouma
The cable stresses are determined last, Fig. 6.8: 2 (3:14)(0:196)2 Awire = D = 0:03017 2 4 = 4 Atotal = (4)cables(26 474)wires/cable(0:03017) (220 000) = 68:75 Central Span = H = A (3 200) 2 T ss (262 500) 2 = 82 ss = tower Side Span Tower tower = A (3 200) 2 T ss (247 000) 2 = 77:2 ss = Side Span Anchor tower = anchor A (3 200) 2
in k ksi in in ksi in in ksi in
in
6{9
Figure 6.8: Cable Stresses If the cables were to be anchored to a concrete block, the volume of the block should be at least equal (1 000) = = 747 000 3 or a cube of approximately 91 ft to V = (112 000) 150 = 3
k lbs k lbs ft ft
28
29
The deck, for all practical purposes can be treated as a continuous beam supported by elastic springs with sti ness K = AL=E (where L is the length of the supporting cable). This is often idealized as a beam on elastic foundations, and the resulting shear and moment diagrams for this idealization are shown in Fig. 6.9.
K=AL/E
Shear
Moment
Victor Saouma
Draft 6{10
Victor Saouma
Draft
Chapter 7
7.2 Greeks
5
The greek philosopher Pythagoras (born around 582 B.C.) founded his famous school, which was primarily a secret religious society, at Crotona in southern Italy. At his school he allowed neither textbooks nor recording of notes in lectures, on pain of death. He taught until the age of 95, and is
Draft 7{2
228. If a builder build a house for some one and complete it, he shall give him a fee of two shekels in money for each sar of surface. 229 If a builder build a house for some one, and does not construct it properly, and the house which he built fall in and kill its owner, then that builder shall be put to death. 230. If it kill the son of the owner the son of that builder shall be put to death. 231. If it kill a slave of the owner, then he shall pay slave for slave to the owner of the house. 232. If it ruin goods, he shall make compensation for all that has been ruined, and inasmuch as he did not construct properly this house which he built and it fell, he shall re-erect the house from his own means. 233. If a builder build a house for some one, even though he has not yet completed it if then the walls seem toppling, the builder must make the walls solid from his own means.
Figure 7.1: Hamurrabi's Code reported to have coined the term mathematics which means literally the \science of learning" (and also the word philosopher meaning \one who loves wisdom"). 6 Aristotle (384-322 B.C.) was Dean of the Lyceum, a college just outside the city gates of Athens, and was a man of universal ability. He is credited with having written in more than 25 di erent elds of knowledge. One of the most in uential men of early civilization. 7 A pupil of Aristotle was Alexander the Great (356-323 B.C.) who founded the city of Alexandria in 323. Upon his death, one of his generals Ptolemy I became Pharaoh and established a library. The library of Alexandria was founded with the private library of Aristotle as a nucleus, and later became the largest of the ancient world, containing about 700,000 scrolls. Many of these scrolls were subsequently brought to the attention of the western world through translations by the arabs. 8 Alexandria was also the seat of the rst university (with a reported enrollment of 14,000 students), and its rst professor of geometry was Euclid (315-250 B.C.). 9 The greatest of the Greeks was Archimedes (287-212) who was one of the greatest physicist of the ancient world and one of its greatest mathematician, Fig. 7.2. He is considered by many as the founder of mechanics because of his treatise \On Equilibrium". He introduced the concept of center of gravity. He refused to write about \practical stu " such as machines, catapults, spiral pumps, and others. It was one such invention (the lens) which kept the Roman armies at bay outside Syracuse for three years. When the city fell, he was supposed to have had his life spared. But the circumstances of his subsequent death are obscure. By some accounts he was killed by an ignorant soldier who disobeyed orders, and by other he was slain because he was too busy solving a mathematical problem to appear in front of the Roman consul and conqueror of Syracuse.
Victor Saouma
7{3
7.3 Romans
10
Science made much less progress under the Romans than under the Greeks. The Romans apparently were more practical, and were not as interested in abstract thinking though they were excellent ghters and builders. 11 As the roman empire expanded, the Romans built great roads (some of them still in use) such as the Via Appia, Cassia, Aurelia Also they built great bridges (such as the third of a mile bridge over the Rhine built by Caesars), and stadium (Colliseum). 12 One of the most notable Roman construction was the Pantheon, Fig. 7.3. It is the best-preserved
Figure 7.3: Pantheon major edi ce of ancient Rome and one of the most signi cant buildings in architectural history. In shape it is an immense cylinder concealing eight piers, topped with a dome and fronted by a rectangular colonnaded porch. The great vaulted dome is 43 m (142 ft) in diameter, and the entire structure is lighted through one aperture, called an oculus, in the center of the dome. The Pantheon was erected by the Roman emperor Hadrian between AD 118 and 128. 13 Marcus Vitruvius Pollio (70?-25 BC) was a Roman architect and engineer. He was an artillery engineer in the service of the rst Roman emperor, Augustus. His Ten Books on Architecture (Vitruvius
Victor Saouma
Draft 7{4
1960) is the oldest surviving work on the subject and consists of dissertations on a wide variety of subjects relating to architecture, engineering, sanitation, practical hydraulics, acoustic vases, and the like. Much of the material appears to have been taken from earlier extinct treatises by Greek architects. Vitruvius's writings have been studied ever since the Renaissance as a thesaurus of the art of classical Roman architecture, Fig. 7.4.
This period, also called the Dark Ages, was marked by a general decline of civilization throughout Europe following the decline and fall of the western Roman Empire. 15 The eastern Roman Empire on the other hand was to continue, and the center of Greek life had by then been transferred to Constantinople. This city exerted great in uence throughout Asia Minor. 16 Hagia Sophia, also Church of the Holy Wisdom, Fig. 7.5, was the most famous Byzantine structure in Constantinople (now Istanbul). Built (532-37) by Emperor Justinian I, its huge size and daring technical innovations make it one of the world's key monuments. The size of its dome though, 112 ft, was nevertheless smaller than the one of the Pantheon in Rome. 17 During that period, the Arabs carried the torch of knowledge, gave birth to algebra, translated some of the great books of the Library of Alexandria. 18 Architecture, was the most important and original art form during the Gothic period, (Anon. xx). The principal structural characteristics of Gothic architecture arose out of medieval masons' e orts to solve the problems associated with supporting heavy masonry ceiling vaults over wide spans. The problem was that the heavy stonework of the traditional arched barrel vault and the groin vault exerted a tremendous downward and outward pressure that tended to push the walls upon which the vault rested outward,
Victor Saouma
7{5
Figure 7.5: Hagia Sophia thus collapsing them. A building's vertical supporting walls thus had to be made extremely thick and heavy in order to contain the barrel vault's outward thrust. Medieval masons solved this di cult problem about 1120 with a number of brilliant innovations. First and foremost they developed a ribbed vault, in which arching and intersecting stone ribs support a vaulted ceiling surface that is composed of mere thin stone panels. This greatly reduced the weight (and thus the outward thrust) of the ceiling vault, and since the vault's weight was now carried at discrete points (the ribs) rather than along a continuous wall edge, separate widely spaced vertical piers to support the ribs could replace the continuous thick walls. The round arches of the barrel vault were replaced by pointed (Gothic) arches which distributed thrust in more directions downward from the topmost point of the arch. Since the combination of ribs and piers relieved the intervening vertical wall spaces of their supportive function, these walls could be built thinner and could even be opened up with large windows or other glazing. A crucial point was that the outward thrust of the ribbed ceiling vaults was carried across the outside walls of the nave, rst to an attached outer buttress and then to a freestanding pier by means of a half arch known as a ying buttress. The ying buttress leaned against the upper exterior of the nave (thus counteracting the vault's outward thrust), crossed over the low side aisles of the nave, and terminated in the freestanding buttress pier, which ultimately absorbed the ceiling vault's thrust. These elements enabled Gothic masons to build much larger and taller buildings than their Romanesque predecessors and to give their structures more complicated ground plans. The skillful use of ying buttresses made it possible to build extremely tall, thin-walled buildings whose interior structural system of columnar piers and ribs reinforced an impression of soaring verticality. 19 Vilet-Le-Duc classical book, (le Duc 1977) provided an in depth study of Gothic architecture.
During the Renaissance there was a major revival of interest in science and art.
Victor Saouma
Draft 7{6
He was the rst to explore concepts of mechanics, since Archimedes, using a scienti c approach. He applied the principle of virtual displacements to analyze various systems of pulleys and levers. He appears to have developped a correct idea of the thrust produced by an arch. 25 In one of his manuscripts there is a sketch of two members on which a vertical load Q is acting and the question is asked: What forces are needed at a and b to have equilibrium? (From the dotted line parallelogram, in the sketch, it can be concluded that he had the right answer). 26 Leonardo also studied the strength of structural materials experimentally. He tried to determine the tensile strength of an iron wire of di erent length (size e ect). 27 He also studied the load carrying capacity of a simply supported uniformly loaded beam and concluded that \the strength of the beam supported at both ends varies inversely as the length and directly as the width" (is this correct? how about the depth of the beam?). 28 For a cantilevered beam he stated \If a beam 2 braccia long supports 100 libre, a beam 1 braccia long will support 200" Finally, Leonardo brie y studied the strength of columns and found that \it varies inversely as its length, but directly as some ratio of its cross section."
24
Leonardo's was the rst indeed to attempt to apply statics in nding the forces acting in members of structures, friction and the rst to perform experiments to determine the strength of structural materials. 30 Interestingly, here is Leonardo's de nition of force, (Penvenuto 1991) \I say that force is a spiritual virtue, an invisible power, which, through accidental exterior violence, is caused by motion and placed and infused into bodies which are thus] removed and deviated from their natural use, giving to such virtue an active life of marvelous power".
29 31
Unfortunatly, these important ndings, were buried in his notes, and engineers in the fteenth and sixteenth centuries continued, as in the Roman era, to x dimensions of structural elements by relying on experience and judgment.
Brunelleschi was a Florentine architect and one of the initiators of the Italian Renaissance. His revival of classical forms and his championing of an architecture based on mathematics, proportion, and perspective make him a key artistic gure in the transition from the Middle Ages to the modern era. Structural Concepts and Systems for Architects
Victor Saouma
7{7
33 He was born in Florence in 1377 and received his early training as an artisan in silver and gold. In 1401 he entered, and lost, the famous design competition for the bronze doors of the Florence Baptistery. He then turned to architecture and in 1418 received the commission to execute the dome of the un nished Gothic Cathedral of Florence, also called the Duomo. The dome, Fig. 7.6 a great innovation both
Figure 7.6: Florence's Cathedral Dome artistically and technically, consists of two octagonal vaults, one inside the other. Its shape was dictated by its structural needs one of the rst examples of architectural functionalism. Brunelleschi made a design feature of the necessary eight ribs of the vault, carrying them over to the exterior of the dome, where they provide the framework for the dome's decorative elements, which also include architectural reliefs, circular windows, and a beautifully proportioned cupola. This was the rst time that a dome created the same strong e ect on the exterior as it did on the interior. 34 Completely di erent from the emotional, elaborate Gothic mode that still prevailed in his time, Brunelleschi's style emphasized mathematical rigor in its use of straight lines, at planes, and cubic spaces. This set the tone for many of the later buildings of the Florentine Renaissance. 35 His in uence on his contemporaries and immediate followers was very strong and has been felt even in the 20th century, when modern architects came to revere him as the rst great exponent of rational architecture.
Alberti was an Italian architect and writer, who was the rst important art theorist of the Renaissance and among the rst to design buildings in a pure classical style based on a study of ancient Roman architecture. Structural Concepts and Systems for Architects
Victor Saouma
Draft 7{8
37
He was born in Genoa, the son of a Florentine noble. He received the best education available in the 15th century. He was pro cient in Greek, mathematics, and the natural sciences. As a poet, a philosopher, and one of the rst organists of his day, Alberti greatly in uenced his contemporaries. 38 Alberti's architectural training began with the study of antique monuments during his rst stay in Rome. Subsequently he joined the papal court in Florence, where he became intensely involved with the cultural life of the city. Probably at this time he became familiar with the mathematical laws of linear perspective, which Brunelleschi had studied. 39 Alberti took took an active part in the literary life of Florence and championed the literary use of Italian rather than the use of Latin. 40 In the late 1440s, Alberti began to work as an architect. Although his buildings rank among the best architecture of the Renaissance, he was a theoretical rather than a practical architect. He furnished the plans of his buildings but never supervised their construction. His De Re Aedi catoria (1485) was the rst printed work on architecture of the Renaissance. He also wrote books on sculpture, the family, government, and literature.
Andrea Palladio was one of the most in uential architects in European history. He was born in Padua, and trained as a stonemason, he later joined the poet Trissino who took him to Rome, where Palladio studied and measured Roman architectural ruins he also absorbed the treatises of Vitruvius. One outcome of these studies was Palladio's Antiquities of Rome (1554) (Palladio 19xx), the principal guidebook to Roman ruins for the next two centuries. 42 In and near Vicenza he designed many residences and public buildings. The best known of these are the Barbarano, Chieregati, Tiene, Porto, and Valmarana palaces and the Villa Capri, or Villa Rotunda. Although the historical antecedents of Palladio's style are the classically Roman-in uenced High Renaissance works of architects such as the Italian Donato Bramante, Palladio's own use of classical motifs came through his direct, extensive study of Roman architecture. He freely recombined elements of Roman buildings as suggested by his own building sites and by contemporary needs, Fig. 7.7 At the same time he shared the Renaissance concern for harmonious proportion, and his facades have a noteworthy simplicity almost austerity and repose. 43 Palladio was the author of an important scienti c treatise on architecture, I Quattro Libri dell'Architettura, (Palladio 19xx) which was widely translated and in uenced many later architects. Its precise rules and formulas were widely utilized, especially in England, and were basic to the Palladian style, adopted by Inigo Jones, Christopher Wren, and other English architects, which preceded and in uenced the neoclassical architecture of the Georgian Style.
7.5.5 Stevin
Stevin, Fig. 7.8, was a Dutch mathematician and engineer who founded the science of hydrostatics by showing that the pressure exerted by a liquid upon a given surface depends on the height of the liquid and the area of the surface. 45 Stevin was a bookkeeper in Antwerp, then a clerk in the tax o ce at Brugge. After this he moved to Leiden where he rst attended the Latin school, then he entered the University of Leiden in 1583 (at the age of 35). While quartermaster in the Dutch army, Stevin invented a way of ooding the lowlands in the path of an invading army by opening selected sluices in dikes. He was an outstanding engineer who
44
Victor Saouma
7{9
Victor Saouma
Draft 7{10
built windmills, locks and ports. He advised the Prince Maurice of Nassau on building forti cations for the war against Spain. 46 The author of 11 books, Stevin made signi cant contributions to trigonometry, geography, forti cation, and navigation. Inspired by Archimedes, Stevin wrote important works on mechanics. In his book De Beghinselen der Weeghconst in 1586 appears the theorem of the triangle of forces giving impetus to statics. In 1586 (3 years before Galileo) he reported that di erent weights fell a given distance in the same time.
Figure 7.9: Galileo from medieval polyphony to harmonic modulation, Galileo came to see Aristotelian physical theology as limiting scienti c inquiry. 48 In 1581 he entered the University of Pisa to study medicine, but he soon turned to philosophy and mathematics, leaving the university without a degree in 1585. For a time he tutored privately and wrote on hydrostatics and natural motions, but he did not publish. 49 In 1589 he became professor of mathematics at Pisa, where he is reported to have shown his students the error of Aristotle's belief that speed of fall is proportional to weight, by dropping two objects of di erent weight simultaneously from the Leaning Tower, thus modern dynamics was born. His contract was not renewed in 1592, probably because he contradicted Aristotelian professors. The same year, he was appointed to the chair of mathematics at the University of Padua, where he remained until 1610. 50 In Padua he achieved great fame, and lecture halls capable of containing 2,000 students from all over Europe were used. In 1592 he wrote Della Scienza Meccanica in which various problems of statics were treated using the principle of virtual displacement. He subsequently became interested in astronomy and built one of the rst telescope through which he saw Jupiter and became an ardent proponent of the Copernican theory (which stated that the planets circle the sun as opposed to the Aristotelian and Ptolemaic assumptions that it was the sun which was circling Earth). This theory being condemned by the church, he received a semio cial warning to avoid theology and limit himself to physical reasoning. When he published his books dealing with the two ways of regarding the universe (which clearly favored the Copernican theory) he was called to Rome by the Inquisition, condemned and had to read his recantation (At the end of his process he murmured the famous e pur se muove).
Victor Saouma
7{11
When he was almost seventy years old, his life shattered by the Inquisition, he retired to his villa near Florence and wrote his nal book, Discourses Concerning Two New Sciences, (Galilei 1974), Fig. 7.10. His rst science was the study of the forces that hold objects together -the dialogue taking place
Figure 7.10: Discourses Concerning Two New Sciences, Cover Page in a shipyard, triggered by observations of craftsmen building the Venetian eet. His second science concerned local motions - laws governing the trajectory of projectiles. A portion of the book dealing with the mechanical properties of structural materials and with the strength of beams. Strength of Materials as a discipline was born. 52 He observed that if we make structures geometrically similar, then with increase of the dimensions they become weaker and weaker, One cannot reason from the small to the large, because many mechanical devices succeed on a small scale that cannot exist in great size. 53 It is interesting to note that when Galileo studied the strength of a cantilevered (wooden) beam with an applied load at the end, Fig. 7.11, he failed to properly understand the exact internal stress/strain
Figure 7.11: \Galileo's Beam" distribution. He determined that the stress is constant throughout the cross section (whereas as we know it varies linearly). 54 Galileo's lifelong struggle to free scienti c inquiry from restriction by philosophical and theological interference stands beyond science. Since the full publication of Galileo's trial documents in the 1870s,
Victor Saouma
Draft 7{12
entire responsibility for Galileo's condemnation has customarily been placed on the Roman Catholic church. This conceals the role of the philosophy professors who rst persuaded theologians to link Galileo's science with heresy. An investigation into the astronomer's condemnation, calling for its reversal, was opened in 1979 by Pope John Paul II. In October 1992 a papal commission acknowledged the Vatican's error.
Hooke was best known for his study of elasticity but also original contributions to many other elds of science. 56 Hooke was born on the Isle of Wight and educated at the University of Oxford. He served as assistant to the English physicist Robert Boyle and assisted him in the construction of the air pump. In 1662 Hooke was appointed curator of experiments of the Royal Society and served in this position until his death. He was elected a fellow of the Royal Society in 1663 and was appointed Gresham Professor of Geometry at Oxford in 1665. After the Great Fire of London in 1666, he was appointed surveyor of London, and he designed many buildings. 57 Hooke anticipated some of the most important discoveries and inventions of his time but failed to carry many of them through to completion. He formulated the theory of planetary motion as a problem in mechanics, and grasped, but did not develop mathematically, the fundamental theory on which Newton formulated the law of gravitation. 58 His most important contribution was published in 1678 in the paper De Potentia Restitutiva. It contained results of his experiments with elastic bodies, and was the rst paper in which the elastic properties of material was discused, Fig. 7.12.
Figure 7.12: Experimental Set Up Used by Hooke \Take a wire string of 20, or 30, or 40 ft long, and fasten the upper part thereof to a nail, and to the other end fasten a Scale to receive the weights: Then with a pair of compasses take the distance of the bottom of the scale from the ground or oor underneath, and set down the
Victor Saouma
7{13
said distance,then put inweights into the said scale and measure the several stretchings of the said string, and set them down. Then compare the several strtchings of the said string, and you will nd that they will always bear the same proportions one to the other that the weights do that made them". This became Hooke's Law = E". 59 Because he was concerned about patent rights to his invention, he did not publish his law when rst discovered it in 1660. Instead he published it in the form of an anagram \ceiinosssttuu" in 1676 and the solution was given in 1678. Ut tensio sic vis (at the time the two symbos u and v were employed interchangeably to denote either the vowel u or the consonant v), i.e. extension varies directly with force.
Born on christmas day in the year of Galileo's death, Newton, Fig. 7.13 was Professor of Mathematics
Figure 7.13: Isaac Newton at Cambridge university. 61 In 1684 Newton's solitude was interrupted by a visit from Edmund Halley, the British astronomer and mathematician, who discussed with Newton the problem of orbital motion. Newton had also pursued the science of mechanics as an undergraduate, and at that time he had already entertained basic notions about universal gravitation. As a result of Halley's visit, Newton returned to these studies. 62 During the following two and a half years, Newton established the modern science of dynamics by formulating his three laws of motion. Newton applied these laws to Kepler's laws of orbital motion formulated by the German astronomer Johannes Kepler and derived the law of universal gravitation. Newton is probably best known for discovering universal gravitation, which explains that all bodies in space and on earth are a ected by the force called gravity. He published this theory in his book Philosophiae Naturalis Principia Mathematica or simply Principia, in 1687, Fig. 7.14. This book marked a turning point in the history of science. 63 The Principia's appearance also involved Newton in an unpleasant episode with the English philosopher and physicist Robert Hooke. In 1687 Hooke claimed that Newton had stolen from him a central
Victor Saouma
Draft 7{14
Figure 7.14: Philosophiae Naturalis Principia Mathematica, Cover Page idea of the book: that bodies attract each other with a force that varies inversely as the square of their distance. However, most historians do not accept Hooke's charge of plagiarism. 64 Newton also engaged in a violent dispute with Leibniz over priority in the invention of calculus. Newton used his position as president of the Royal Society to have a committee of that body investigate the question, and he secretly wrote the committee's report, which charged Leibniz with deliberate plagiarism. Newton also compiled the book of evidence that the society published. The e ects of the quarrel lingered nearly until his death in 1727. 65 In addition to science, Newton also showed an interest in alchemy, mysticism, and theology. Many pages of his notes and writings particularly from the later years of his career are devoted to these topics. However, historians have found little connection between these interests and Newton's scienti c work.
Victor Saouma
7{15
Leonhard Euler was born in Basel and early on caught the attention of John Bernoulli whose teaching was attracting young mathematicians from all over Europe, Fig. 7.15. He obtained his Master
Figure 7.15: Leonhard Euler at age 16, and before the age of 20 won a competition from the French Academy of Sciences. At age 20 he moved to the Russian Academy of Sciences in St Petersburg along with the two sons of John Bernoulli (Nicholas and Daniel). He was appointed professor of physics in 1730 and professor of mathematics in 1733. In 1741 he became professor of mathematics at the Berlin Academy of Sciences at the urging of the Prussian king Frederick the Great. Euler returned to St. Petersburg in 1766, remaining there until his death. 70 Although hampered from his late 20s by partial loss of vision and in later life by almost total blindness, Euler produced a number of important mathematical works and hundreds of mathematical and scienti c memoirs. In his Introduction to the Analysis of In nities, Euler gave the rst full analytical treatment of algebra, the theory of equations, trigonometry, and analytical geometry. In this work he treated the series expansion of functions and formulated the rule that only convergent in nite series can properly be evaluated. He also discussed three-dimensional surfaces and proved that the conic sections are represented by the general equation of the second degree in two dimensions. Other works dealt with calculus, including the calculus of variations, number theory, imaginary numbers, and determinate and indeterminate algebra. Euler, although principally a mathematician, made contributions to astronomy, mechanics, optics, and acoustics. 71 In Russia he wrote a famous book in mechanics in which instead of applying the geometrical methods used by Newton, he introduced analytical methods. 72 As a mathematician, Euler was interested principally in the geometrical forms of elastic curves. He approached problems from the point of view of variational calculus and in the introduction of his book Methodus inveniendi lineas curva ... he stated Since the fabric of the universe is most perfect, and is the work of a most wise Creator, nothing whatsover takes place in the universe in which some relation o maximum an minimum does not appear. Therefore there is absolutely no doubt that every e ect in the universe can be explained as satisfactorily from nal causes, by the aid of the method of maxima and minima, as it can from the e ective causes themselves...
73
Euler obtained a near exact expression for the de ection of a cantilever subjected to a point load, and
Victor Saouma
Draft 7{16
74
Figure 7.16: Coulomb analysis of the ber stresses in exed beam with rectangular cross section (Sur une Application des Regles de maximis et minimis a quelques problemes de statique relatifs a l'architecture in 1773). He used Hooke's law, placed the neutral axis in its exact position, developed the equilibrium of forces on the cross section with external forces, and then correcly determined the stresses. He also worked on friction (\Coulomb friction") and on earth pressure. 75 Coulomb did also research on magnetism, friction, and electricity. In 1777 he invented the torsion balance for measuring the force of magnetic and electrical attraction. With this invention, Coulomb was able to formulate the principle, now known as Coulomb's law, governing the interaction between electric charges. In 1779 Coulomb published the treatise Theorie des machines simples (Theory of Simple Machines), an analysis of friction in machinery. After the war Coulomb came out of retirement and assisted the new government in devising a metric system of weights and measures. The unit of quantity used to measure electrical charges, the coulomb, was named for him. 76 Navier (1785-1836) Navier was educated at the Ecole Polytechnique and became a professor there in 1831. Whereas the famous memoir of Coulomb (1773) contained the correct solution to numerous important problems in mechanics of materials, it took engineers more than forty years to understand them correctly and to use them in practical application 77 In 1826 he published his Lecons (lecture notes) which is considered the rst great textbook in mechanics for engineering. In it he developed the rst general theory of elastic solids as well as the rst systematic treatment of the theory of structures. 78 It should be noted that no clear division existed between the theory of elasticity and the theory of structures until about the middle of the nineteenth century (Coulomb and Navier would today be considered professional structural engineers). 79 Three other structural engineers who pioneered the development of the theory of elasticity from that point on were Lame, Clapeyron and de Saint-Venant. Lam'e published the rst book on elasticity in 1852, and credited Clapeyron for the theorem of equality between external and internal work. de Saint-Venant was perhaps the greatest elasticians who according to Southwell \... combined with high mathematical ability an essentially practical outlook which gave direction to all his work". In 1855-6 he published his classical work on torsion, exure, and shear stresses.
Victor Saouma
7{17
From 1857 the evolution of a comprehensive theory of structures proceeded at astonishing rate now that the basic and requisite principles had been determined. 81 Great contributors in that period include: Maxwell ( rst analysis of indeterminate structures), Culmann (graphics statics), Mohr (Mohr's circle, indeterminate analysis), Castigliano (1st and 2nd theorems), Cross (moment distribution), Southwell (relaxation method).
7.8.2 Ei el Tower
82
The Ei el Tower was designed and built by the French civil engineer Alexandre Gustave Ei el for the Paris World's Fair of 1889. The tower, without its modern broadcasting antennae, is 300 m (984 ft) high. The lower section consists of four immense arched legs set on masonry piers. The legs curve inward until they unite in a single tapered tower. Platforms, each with an observation deck, are at three levels on the rst is also a restaurant. 83 The tower, constructed of about 6300 metric tons (about 7000 tons) of iron, has stairs and elevators. A meteorological station, a radio communications station, and a television transmission antenna, as well as a suite of rooms that were used by Ei el, are located near the top of the tower.
Victor Saouma
Draft 7{18
89
7.8.5 Maillart
From (Billington 1973)
92
Robert Maillart was born on February 6, 1872, in Bern, Switzerland, where his father, a Belgian citizen, was a banker. He studied civil engineering at the Federal Institute of Technology in Zurich and graduated in 1894. Ironically, one of his lowest grades was in bridge design, even though he is regarded today as one of the half dozen greatest bridge designers of the twentieth century. 93 For eight years following his graduation, he worked with di erent civil engineering organizations. In 1902, he founded his own rm for design and construction thereafter, his business grew rapidly and expanded as far as Russia and Spain. In the summer of 1914, he took his wife and three children to Russia. Since the World War prevented their return to Switzerland, Maillart stayed and worked in Russia until 1919, when his business was liquidated by the Revolution. Forced to ee, he returned to Switzerland penniless and lonely, his wife having died in Russia. 94 Because of these misfortunes Maillart felt unable to take up the construction business again and henceforth concentrated on design alone. He opened an o ce in Geneva in 1919 and branches in Bern and Zurich in 1924. 95 During the twenties he began to develop and modify his ideas of bridge design and from 1930, when the Salginatobel and Landquart Bridges were completed, until his death in 1940, he produced over thirty bridge designs of extraordinary originality. Unfortunately, no Swiss municipality would accept his designs for prominent urban locations. 96 In 1936, he was elected an honorary member of the Royal institute of British Architects (R.I.B.A.) although he had never o cially acted as architect on any project. The 1941 rst edition of Space, Time and Architecture by art historian Siegfried Giedion introduced Maillart to a wide public in the U.S.A. Finally, Max Bill's 1949 book, Robert Maillart, with its photographs and commentary on nearly all Maillart's bridges powerfully presented him as an artist of rst rank.
Victor Saouma
7{19
He attended the Civil Engineering School in Bologna and established his own rm in 1920. His rst major commission (a stadium in Florence, 1932) features cantilevered beams and a daringly exposed concrete structure. For airplane hangars he used reinforced concrete to cover enormous spans with a light but strong latticework. 99 Nervi considered himself primarily an engineer and technician, not an architect, and he strove primarily for strength through form. He maintained that the strong aesthetic appeal of his buildings was simply a by-product of their structural correctness. His introduction of a versatile new type of reinforced concrete layers of ne steel mesh sprayed with cement mortar made possible one of his masterpieces, the Turin Exposition Hall (1949), in which the approximately 76-m (250-ft) corrugated lattice roof (only about 5 cm thick) creates an immense interior space as dramatic as a cathedral. 100 The best known and most in uential is probably his Palazetto dello Sport (Small Sport Palace, 1960, Rome), Fig. 7.17. Encircled by Y-shaped supports and topped by a shallow scalloped concrete dome,
Figure 7.17: Nervi's Palazetto Dello Sport this building has become a paradigm of the 20th-century sports arena.
7.8.7 Khan
Fazlur Khan was born in 1929 in Dacca India, (Anon. xx). After obtaining a B.A. in engineering from
the University of Dacca in 1950, Khan worked as assistant engineer for the India Highway Department and taught at the University of Dacca. Qualifying for a scholarship in 1952, he enrolled at the University of Illinois, Champaign-Urbana, where he received master's degrees in both applied mechanics and structural engineering and a Ph.D. in structural engineering. He returned brie y to Pakistan and won an important position as executive engineer of the Karachi Development Authority. Frustrated by administrative demands that kept him from design work, however, he returned to the United States and
Victor Saouma
Draft 7{20
joined the prestigious architectural rm of Skidmore, Owings & Merrill in Chicago in 1955, eventually becoming a partner (1966). Among his many designs for skyscrapers are Chicago's John Hancock Center (1970) and the Sears Tower (1973), which are among the world's tallest buildings, and One Shell Plaza in Houston, Texas. The Sears Tower was his rst skyscraper to employ his "bundled tube" structural system, which consists of a group of narrow steel cylinders that are clustered together to form a thicker column. The system was innovative because it minimized the amount of steel needed for high towers, eliminated the need for internal wind bracing (since the perimeter columns carried the wind loadings), and permitted freer organization of the interior space. His later projects included the strikingly di erent Haj Terminal of the King Abdul Aziz International Airport, Jiddah, Saudi Arabia (1976-81), and King Abdul Aziz University, also in Jiddah (1977-78).
7.8.8
101
et al.
To name just a few of the most in uential Architects/Engineers: Menn, Isler, Candella, Torroja, Johnson, Pei, Calatrava, ...
Victor Saouma
7{21
by
Felix Candela
The title of my lecture is New Architecture but I cannot avoid the feeling that I have not too much to do with this subject. I don't think I can speak of my work as of any new architecture or even as architecture at all, and perhaps the same could be said of Maillart's work. But, of course, it all depends on what you consider architecture and there is not anymore a general consent about the meaning of this word, But, anyway, upon discussing this with David Billington, he told me it could be interesting to know what had been the in uence of Maillart on my development, and all of a sudden I realized that he may have been one of the strongest in uences at the critical moment in my career in which I was trying to become a builder of shells. But let me speak rst about my background, because it may be important to know what impels people to do things and the circumstances and di culties that they had to deal with in order to achieve their purposes. I was trained as an architect with, you may say, quite a backward kind of curriculum, in Madrid during the thirties. We had only one course in strength of materials, but it was a very good course, dealing mainly with theory of elasticity and following the classical and rigoristic French tradition. As you can imagine, most students considered the matter completely useless for their professional practice and, as it required some knowledge of mathematics, it was very di cult for most of them to pass the examination. This gave me opportunity to do some private tutoring to my classmates, which was a very instructive manner to make some money to pay for my studies. As a result, I became more familiar with the theoretical bases of the current methods of calculation of indeterminate structures. I discovered later that this modest background made me more knowledgeable on the matter than most practicing engineers whose training and interest tend to be directed towards mastering the accepted methods of analysis rather than questioning the basic hypotheses. Anyway, since I never had a high opinion of myself as an artist, I was more interested in the technical part of the curriculum and began to read extensively about structures. Among my lectures I found several French and German papers dealing with shells which were beginning to be in vogue at that time in Europe. Examples of such structures built in Germany and France could be found in magazines and Torroja was building the famous roof of the "Fronton Recoletos" in Madrid, with an unusual shape and a record span. Shells appeared to be an intriguing challenge for me, and I dreamed about the possibility of building some in the future. But my lack of experience and my youthful faith in the impressive wisdom displayed in learned magazines led me to believe that the key to shell design was in complete mathematical calculation, and I tried, rather unsucessfully, to understand and follow them and to make some sense of their results. I was not the only one misled and discouraged by the mathematical barrier so cunningly deployed by German engineers, a clever move which secured them practically an exclusive on the construction of barrel vaults for more than twenty years, hindering the normal employment of such structures during the same time. However, such was my enthusiasm with this mathematical approach that I managed to get a fellowship to go to Germany, hoping to learn something more from the German professors. But the outbreak of the Spanish Civil War saved me from such an ordeal. I could not leave the country and ended in Mexico after three years of military service, with no more baggage than my bare hands and no further addition to my academic background. After several years of general practice in Mexico, as draftsman, designer and contractor, I recalled my old fancy with shells and began to collect again papers on the subject. Whatever I learned from then on was to be the hard way, working alone, with no direct help from any university or engineering o ce. But I am indebted to many people who did help me through their
Victor Saouma
Draft 7{22
writings and Maillart was one of the foremost. I discovered him in Giedion's Space, Time and Architecture and then I got Max Bill's book with its invaluable collection of Maillart's essays. I devoured his articles about "Reinforced Concrete Design and Calculation" (he was very careful to di erentiate the meaning of such words and to avoid the more than semantic confusion prevalent nowadays in English-speaking countries)., "The Engineer and the Authorities" which expresses his position in front of the establishment and "Mass and Quality in Reinforced Concrete Structures." Very short papers, indeed, but well provided with opinions, something I could rarely nd in other engineering articles. I learned later that to express personal opinions is considered bad taste among technical writers. Any discussion should be restricted to insigni cant details, but never touch fundamental dogmas, in a fashion curiously similar to what could be expected of the councils of the Church or the meetings of any Politbureau. But my attitude with respect to calculations of reinforced concrete structures was becoming unorthodox, being tired perhaps of performing long and tedious routines whose results were not always meaningful. Therefore, I found Maillart's thoughts delightfully sympathetic and encouraging. If a rebel was able to produce such beautiful and sound structures there could not be anything wrong with becoming also a rebel, which was besides, my only way to break the mystery surrounding shell analysis. Thus, I started to follow the bibliographic tread and met, through their writings, with Freudenthal, Johansen, Van der Broek, Kist, Saliger, Kacinczy and so many others who showed me there was more than a single and infallible manner to approach structural analysis. The discovery of rupture methods, with their emphasis on simple statics and their bearing on the actual properties of construction materials and their behavior in the plastic range, allowed me to trust in simpli ed procedures to understand and analyze the distribution of stresses in shell structures. It also helped me to get out of my naive belief in the indisputable truth of the printed word and to start reading with a new critical outlook. No longer did I need to believe whatever was in print, no matter how high-sounding the name of the author. I could make my own judgements about what methods of stress analysis were better suited for my practice. Since I was working practically alone, I could not a ord nor had time for complex calculations and did welcome Maillart's advice that simpler calculations are more reliable than complex ones, especially for somebody who builds his own structures. This was exactly my case and, since most structures I was building were of modest scale, I could control what was happening, check the results and con rm the accuracy of my judgement or correct my mistakes. In a way, I was working with full scale models. I understand that this was also true of Maillart who in many cases was the actual builder of his designs. Following the general trend to mess up issues, there has been a lot of speculation about the engineer as an artist and in some instances, like in the case of Nervi, about the engineer as an architect (as if the title of architect could confer, per se, artistic ability to its holder) but few people realize that the only way to be an artist in this di cult specialty of building is to be your own contractor. in countries like this, where the building industry has been thoroughly and irreversibly fragmented and the responsibility diluted among so many trades, it may be shocking to think of a contractor as an artist but it is indeed the only way to have in your hands the whole set of tools or instruments to perform the forgotten art of building, to produce "works of art" which, by the way, was the common expression to designate a bridge in the old French engineering vocabulary. Implicit in the above statement is the fact that you have to be, besides your own structural designer and calculator and perhaps your own architect, also your own contractor, a very di cult proposition in some countries where such mergings of today's disparate professions may even be considered unlawful. This means, of course, that the price for being the master of your trade is to accept the whole responsibility for the good performance of the structure, and not too many people today would readily endorse such an awesome commitment. I am not advocating a return to the past history is an irreversible process. I am simply stating that the Maillart phenomenom could not happen under today's situation of the industry. I like to think, however, that Maillart did not judge himself an artist. As Picasso said of himself "he was not looking for beauty he found it". His main concerns must have been e ciency and economy of means, since to be able to build one of his bridges he had to win a bidding competition and prove that
Victor Saouma
7{23
he could do it cheaper than anybody else. But an e cient and economical structure has not necessarily to be ugly. Beauty has no price tag and there is never one single solution to an engineering problem. Therefore, it is always possible to modify the whole or the parts until the ugliness disappears. This aversion to ugliness is quite the opposite of the task of the professional artist who has to produce beauty as an obligation or of today's star-architect who has to be original at any cost in each new project. Maillart's works did not need to be beautiful. This word did not even exist in the practical world of the serious citizens who had to judge his competitive bids. He achieved a beauty without need or purpose just for the pure joy of it. The kind of joy that you can feel also in the works of Haydn or Vivaldi. They were simply enjoying what they were doing, and so was obviously Maillart. He did also possess that rare quality, source of artistic creation and of all invention, of being able to challenge the conventional wisdom and come up with the obvious solution, one, nevertheless, which nobody could think of before. I can imagine the ts of rage and jealousy of some of his contemporary colleagues at the sight of one of his bridges (Landquart or Schwandbach), in which the curved route is supported in a straight arched slab. The problem with this unusual combination - which, of course, looks perfectly logical after the fact - is that it was very di cult, if not impossible, to analyze with the methods available at that time. But Maillart would not take any unnecessary risk and rst he tried the soundness of his approximated calculations in a small example (the Halbkern Bridge) with a span of only fteen meters. This was his testing model which gave him rm ground from which to extrapolate at the next opportunity. I would like to insist at this moment c-n something that everybody knows but which is easily forgotten that all calculations, no matter how sophisticated and complex, can not be more than rough approximations of the natural phenomenon they try to represent by means of a mathematical model. The complexity, or even elegance, of such a model bears no relation at all with the degree of approximation. There is not such a thing as an exact method of structural analysis and, notwithstanding the popular belief in the letter of the codes, the accuracy of any calculation is still a question of personal judgement. This fortunate circumstance allows engineering to reach sometimes the highest category of art, to the despair of dull and in exible technicians. If I nd something lacking in this commendable conference in memory of one of the greatest engineers of all times it is that the side of Maillart's personality as a rebel, with his tireless and successful struggle against the establishment of his times, has not been su ciently stressed.
Victor Saouma
Draft 7{24
Victor Saouma
Draft
Chapter 8
8.1 Geometry
1 This sotrage house, built by Maillart in Chiasso in 1924, provides a good example of the mariage between aesthetic and engineering. 2 The most strking feature of the Magazini Generali is not the structure itself, but rather the shape of its internal supporting frames, Fig. 8.1. 3 The frame can be idealized as a simply supported beam hung from two cantilever column supports. Whereas the beam itself is a simple structural idealization, the overhang is designed in such a way as to minimize the net moment to be transmitted to the supports (foundations), Fig. 8.2.
8.2 Loads
4
The load applied on the frame is from the weights of the roof slab, and the frame itself. Given the space between adjacent frames is 14.7 ft, and that the roof load is 98 , and that the total frame weight is 13.6 kips, the total uniform load becomes, Fig. 8.3:
psf
qroof = (98) (14:7) = 1:4 (13:6) = 0:2 qframe = (63 :6) qtotal = 1:4 + 0:2 = 1.6
psf ft k k/ft ft k/ft
k/ft
Draft 8{2
ACTUAL FRAME
9.2 ft
63.6 ft
Figure 8.1: Magazzini Generali Overall Dimensions, (Billington and Mark 1983)
Figure 8.2: Magazzini Generali Support System, (Billington and Mark 1983)
Victor Saouma
8{3
8.3 Reactions
5
Reactions for the beam are determined rst taking advantage of symmetry, Fig. 8.4:
We note that these reactions are provided by the internal shear forces.
q TOTAL = 1.6 k/ft
(8.2-a) (8.2-b)
63.6 ft
51 k
51 k
Figure 8.4: Magazzini Generali Beam Reactions, (Billington and Mark 1983)
8.4 Forces
6
The internal forces are pimarily the shear and moments. Those can be easily determined for a simply supported uniformly loaded beam. The shear varies linearly from 51 kip to -51 kip with zero at the center, and the moment diagram is parabolic with the maximum moment at the center, Fig. 8.5, equal to: 2 (1:6) (63:6) 2 = 808 Mmax = qL = (8.3) 8 8
k/ft ft k.ft
The externally induced moment at midspan must be resisted by an equal and opposite internal moment. This can be achieved through a combination of compressive force on the upper bers, and tensile ones on the lower. Thus the net axial force is zero, however there is a net internal couple, Fig. 8.6.
Victor Saouma
Draft 8{4
51 K
SHEAR FORCE
25 K 0 25 K 51 K L L/2 x
MOMENT
Mmax
Figure 8.5: Magazzini Generali Shear and Moment Diagrams (Billington and Mark 1983)
q TOTAL
A d VA
C M T
Figure 8.6: Magazzini Generali Internal Moment, (Billington and Mark 1983)
Victor Saouma
8{5
(8.4-a)
k
88
(8.4-b)
8 Because the frame shape (and thus d(x)) is approximately parabolic, and the moment is also parabolic, then the axial forces are constants along the entire frame, Fig. 8.7.
M MOMENT DIAGRAM
d FRAME
Figure 8.7: Magazzini Generali Similarities Between The Frame Shape and its Moment Diagram, (Billington and Mark 1983)
9
The axial force at the end of the beam is not balanced, and the 88 kip compression must be transmitted to the lower chord, Fig. 8.8. Fig. 8.9 This is analogous to the forces transmiited to the support by a
88 k 88 k 88 k 88 k
Tension
Compression Horizontal Component Tied Arch Cable Force Axial Force Vertical Reaction
Figure 8.8: Magazzini Generali Equilibrium of Forces at the Beam Support, (Billington and Mark 1983) tied arch. 10 It should be mentioned that when a rigorous computer analysis was performed, it was determined that the supports are contributing a compression force of about 8 kips which needs to be superimposed over the central values, Fig. 8.9.
Victor Saouma
Draft 8{6
-88 k - 8 k = -96 k 16 k 88 k - 8 k = 80 k
16 k
Figure 8.9: Magazzini Generali E ect of Lateral Supports, (Billington and Mark 1983)
Victor Saouma
Draft
Chapter 9
Draft 9{2
4. Importance of the member in the structure. 5. Chance of warning prior to failure.
4
Two major design philosophies have emerged 1. Working Stress Method 2. Ultimate Strength Method
This is the simplest of the two methods, and the one which has been historically used by structural engineers. 6 Structural elements are designed for their service loads, and are dimensioned such that the stresses do not exceed some predesignated allowable strength, Fig. 9.1.
Figure 9.1: Load Life of a Structure In R/C this method was the one adopted by the ACI (American Concrete institute) code up to 1971, Working Stress Design Method (WSD). 8 The AISC (American Institute of Steel Construction) code refers to it as the Allowable Stress Design (ASD) and was used until 1986.
7
Victor Saouma
9{3
In this method: 1. All loads are assumed to have the same average variability. 2. The entire variation of the loads and the strengths is placed on the strength side of the equation.
yld < all = F:S:
(9.1)
where F:S: is the factor of safety. 10 Major limitations of this method 1. An elastic analysis can not easily account for creep and shrinkage of concrete. 2. For concrete structures, stresses are not linearly proportional to strain beyond 0:45fc0 . 3. Safety factors are not rigorously determined from a probabilistic approach, but are the result of experience and judgment.
11
Allowable strengths are given in Table 9.1. Steel, AISC/ASD Tension, Gross Area Ft = 0:6Fy Tension, E ective Net Area Ft = 0:5Fu Bending Fb = 0:66Fy Shear Fv = 0:40Fy Concrete, ACI/WSD Tension 0 Compression 0:45fc0 E ective net area will be de ned in section ??. Table 9.1: Allowable Stresses for Steel and Concrete
Probabilistic Preliminaries
In this approach, it is assumed that the load Q and the resistance R are random variables. Typical frequency distributions of such random variables are shown in Fig. 9.2. The safety margin is de ned as Y = R ; Q. Failure would occur if Y < 0 Q and R can be combined and the result expressed logarithmically, Fig. 9.3.
Failure would occur for negative values of X 16 The probability of failure Pf is equal to the ratio of the shaded area to the total area under the curve in Fig. 9.3.
R X = ln Q
(9.2)
Victor Saouma
Draft 9{4
Victor Saouma
9{5
R If X is assumed to follow a Normal Distribution than it has a mean value X = ln Q and a m standard deviation . 18 We de ne the safety index (or reliability index) as =X 1 19 For standard distributions and for = 3:5, it can be shown that the probability of failure is Pf = 9 091 or 1:1 10;4. That is 1 in every 10,000 structural members designed with = 3:5 will fail because of either excessive load or understrength sometime in its lifetime. 20 Target values for are shown in Table 9.2.
Type of Load/Member DL + LL Members 3.0 DL + LL Connections 4.5 DL + LL + WL Members 3.5 DL + LL +EL Members 1.75 Ductile Failure Sudden Failures
AISC ACI
3-3.5 3.5-4
Because the strengths and the loads vary independently, it is desirable to have one factor to account for variability in resistance, and another one for the variability in loads. 22 These factors are referred to as resistance factor and Load Factor respectively. The resistance factor is de ned as m =R (9.3) Rn exp(;0:55 VR ) where RM RN and VR are the mean resistance, the nominal resistance (to be de ned later), and the coe cient of variation of the resistance.
9.3.2 Discussion
23
ACI refers to this method as the Strength Design Method, (previously referred to as the Ultimate Strength Method). 24 AISC refers to it as Load and Resistance Factor Design (LRFD). 25 Terms such as failure load should be avoided it is preferable to refer to a structure's Limit State load. 1 26 The general form is (LRFD-A4.1)
Rn
i Qi
(9.4)
where is a strength reduction factor, less than 1, and must account for the type of structural element, Table 9.3.
1
Throughout the notes we will refer by this symbol the relevant design speci cation in the AISC code.
Victor Saouma
Draft 9{6
Type of Member
ACI
AISC
0.9 0.9 0.75 0.70 0.85 0.70 0.9 0.75 0.85 0.9 0.75 0.65
Rn is the nominal resistance (or strength). Rn is the design strength. i is the load factor corresponding to Qi and is greater than 1. i Qi is the required strength based on the factored load:
AISC
The various factored load combinations which must be considered are 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. 7. 1.4D 1.2D+1.6L+0.5(Lr or S) 1.2D+0.5L (or 0.8W)+1.6(Lr or S) 1.2D+0.5L+0.5(Lr or S)+1.3W 1.2D+0.5L(or 0.2 S)+1.5E 0.9D+1.3W(or 1.5 E) 1.4D+1.7L 0.75(1.4D+1.7L+1.7W) 0.9D+1.3W 1.05D+1.275W 0.9D+1.7H 1.4D +1.7L+1.7H 0.75(1.4D+1.4T+1.7L)
ACI
Victor Saouma
9{7
8. 1.4(D+T) where D= dead L= live Lr= roof live W= wind E= earthquake S= snow T= temperature H= soil. We must select the one with the largest limit state load. 28 Thus, in this method, we must perform numerous analysis, one for each load, of a given structure. For trusses, this is best achieved if we use the matrix method, invert the statics matrix B ], and multiply B ];1 by each one of the load cases, (Refer to Section ??). For the WSD method, we need not perform more than one analysis in general. 29 Serviceability Limit States must be assessed under service loads (not factored). The most important ones being 1. De ections 2. Crack width (for R/C) 3. Stability
9.4 Example
Example 9-18: LRFD vs ASD
To illustrate the di erences between the two design approaches, let us consider the design of an axial member, subjected to a dead load of 100 and live load of 80 . Use A36 steel.
k k
ASD: We consider the total load P = 100 + 80 = 180 . From Table 9.1, the allowable stress is
0:6
yld
= 0:6 36 = 21:6
ksi
k k
From Table 9.3 = 0:9, and Rn = (0:9)A yld . Hence, applying Eq. 9.4 the cross sectional area should be 2 A = i Qi = (0:248 9)(36) = 7:65
in
yld
Note that whereas in this particular case the USD design required a smaller area, this may not be the case for di erent ratios of dead to live loads.
To assist in the preliminary design/dimensioning of structures, Table 9.4 provides average, maximum and typical spans for various types of structures.
Victor Saouma
Draft 9{8
Plywood Planks Joists Beams Girders Gable bents Trusses I Beams Joists Plate and I girders Trusses Gable bents Arches span to rise Arches span to thickness Simple suspension (span to rise) Cable stayed
TIMBER
Solid slabs 28 32 10-25 Slabs with drops and capitals 30 36 20-35 Two-way slab on beams 30 36 20-35 Wa e slabs 20 24 30-40 Joists 22 26 25-45 Beams 16 20 15-40 Girders 12 16 20-60 Gable bents 24 30 40-80 Arches span to rise 8 12 60-150 Arches span to thickness 30 40 Cylindrical thin shell roof (Min. thickness may govern) Longitudinal span to Structural depth 12 15 50-70 Transverse span to thickness 50 60 12-30 Solid slabs 40 44 20-35 Slabs with drops 44 48 35-45 Two-way slab on beams 44 48 35-45 Wa e slabs 28 32 35-70 Cored slabs 36 40 30-60 Joists 32 36 40-60 Beams 24 28 30-80 Girders 20 24 40-120 Cylindrical thin shell roof (Min. thickness may govern) Longitudinal span to structural depth 15 20 60-120 Transverse span to thickness 60 70 15-35 Table 9.4: Approximate Structural Span-Depth Ratios for Horizontal Subsystems and Components (Lin and Stotesbury 1981)
REINFORCED CONCRETE
PRESTRESSED CONCRETE
Victor Saouma
Draft
Chapter 10
A) COMPOSITE BEAM
B) OTHER FRAMING
C) CROSS BRACING
Figure 10.1: Lateral Bracing for Steel Beams buckling. 4 By the end of this lecture you should be able to select the most e cient section (light weight with adequate strength) for a given bending moment and also be able to determine the exural strength of a given beam.
Draft 10{2
10.1 Nominal Strength
5
The strength requirement for beams in load and resistance factor design is stated as
b Mn
Mu
(10.1)
where:
The equations given in this chapter are valid for exural members with the following kinds of cross section and loading: 1. Doubly symmetric (such as W sections) and loaded in plane of symmetry 2. Singly symmetric (channels and angles) loaded in plane of symmetry or through the shear center parallel to the web1 .
A beam is classi ed as laterally supported depending on Lb which is the distance between lateral supports (or unbraced length) and Lp .
Lb < Lp (10.2) 300 Lp = p ry (10.3) Fy r y (10.4) ry = I A where ry is the radius of gyration with respect to the (minor) y axis (as opposed to the major x axis).
ksi
The strength of exural members is limited by: Plastic Hinge: at a particular cross section, Fig. 10.2. local buckling: of a cross-sectional element (e.g. the web or the ange), Fig. 10.3. Lateral-Torsional buckling: of the entire member, Fig. 10.4.
8
Accordingly, the LRFD manual classi es steel sections as Compact sections: No local buckling can occur. Strength is based on the plastic moment. Partially compact sections: Where local buckling may occur Slender sections: where lateral torsional buckling may occur. We will cover only the rst two cases. 10 Shear should be checked, however with exception of short beams (and no self-respecting architect will ever conceive such a thing:-), exure generally controls.
9
1
Victor Saouma
10{3
wu
11 00 00 11 00 11
Mp y
2 )/8 M p=(wL
bf
tw
hf hc
COMPACT
FLANGE BUCKLING
WEB BUCKLING
Victor Saouma
Draft 10{4
A B
COMPRESSION FLANGE
A B A
For compact sections, the mode of failure is the formation of a plastic hinge that is the section is fully plasti ed. Hence we shall rst examine the bending behavior of beams under limit load. Then we will relate this plastic moment to the design of compact sections.
Victor Saouma
10{5
When the yield stress is reached at the extreme ber, the nominal moment strength Mn, is referred to as the yield moment My and is computed as
Mn = My = SxFy
(10.5)
(assuming that bending is occurring with respect to the x ; x axis). 14 When across the entire section, the strain is equal or larger than the yield strain (" "y = Fy =Es ) then the section is fully plasti ed, and the nominal moment strength Mn is therefore referred to as the plastic moment Mp and is determined from
Mp = Fy
where
ydA = Fy Z
(10.6) (10.7)
Z = ydA
def
is the Plastic Section Modulus. 15 The plastic section modulus Z should not be confused with the elastic section modulus S de ned, Eq. 5.25 as
I S = d= 2 Z I def = y2 dA
A
(10.8-a) (10.8-b)
16
The section modulus Sx of a W section can be roughly approximated by the following formula
2 Sx wd=10 or Ix Sx d 2 wd =20
(10.9)
Zx wd=9
(10.10)
Victor Saouma
Draft 10{6
10.3.2 Design of Compact Sections
17
A section is compact if the following conditions are met: 1. Flanges are continuously connected to the web 2. Width to thickness ratios, known as the slenderness ratios, of the ange and the web must not exceed the limiting ratios p de ned as follows: Flange 2btff hc Web t w
hc are tabulated in Sect. 3.6. Note that 2btff and t w p p
65 p=p Fy 640 p p = Fy
(10.11)
18
The nominal strength Mn for laterally stable compact sections according to LRFD is
Mn = Mp
where:
(10.12)
19
Mp plastic moment strength = ZFy Z plastic section modulus Fy speci ed minimum yield strength Note that section properties, including Z values are tabulated in Section 3.6.
If the width to thickness ratios of the compression elements exceed the p values mentioned in Eq. 10.11 but do not exceed the following r , the section is partially compact and we can have local buckling. Flange: Web:
p< p<
2tf
bf
hc tw
r r
where:
(10.13)
21
speci ed minimum yield stress in kksi width of the ange thickness of the ange unsupported height of the web which is twice the distance from the neutral axis to the inside face of the compression ange less the llet or corner radius. tw thickness of the web. Fr residual stress = 10:0 ksi for rolled sections and 16:5 ksi for welded sections. The nominal strength of partially compact sections according to LRFD is, Fig. 10.7
p) M Mn = Mp ; (Mp ; Mr )( ; p r; p
Fy bf tf hc
(10.14)
Victor Saouma
10{7
6
Compact
Mp
Partially Compact
Slender
Mr
Flanges Web
2tf
bf
65 p F
p
y
pF141 ;F
y
hc tw
640 p F
970 p F
Figure 10.7: Nominal Moments for Compact and Partially Compact Sections where:
Mr Residual Moment equal to (Fy ; Fr )S bf =2tf for I-shaped member anges and hc=tw for beam webs.
associated with the one being
22
All other quantities are as de ned earlier. Note that we use the violated (or the lower of the two if both are).
If the width to thickness ratio exceeds r values of ange and web, the element is referred to as slender compression element. Since the slender sections involve a di erent treatment, it will not be dealt here.
10.6 Examples
Example 10-19: Z for Rectangular Section
Determine the plastic section modulus for a rectangular section, width b and depth d.
Victor Saouma
Draft 10{8
Solution:
1. The internal plastic moment is equal to
d = F b d2 M = Fy b d y 4 22
Force
| {z }
(10.15)
2. The yield stress, Fy , plastic moment Mp and plastic section modulus Z are related by:
p Z=M Z
(10.16) (10.17)
3. Substituting, we get:
Solution:
k/ft
Victor Saouma
10{9
2. Compute the factored load moment Mu . For a simply supported beam carrying uniformly distributed load, Mu = wu L2 =8 = (1:52)(20)2=8 = 76 Assuming compact section, since a vast majority of rolled sections satisfy p for both the ange and the web. The design strength b Mn is
b Mn = b Mp = b Zx Fy
b Mn = Mu
in
From the notes on Structural Materials, we select a W12X22 section which has a Zx = 29:3 (22)(12) Note that Zx is approximated by wd 9 = 9 = 29:3. 4. Check compact section limits p for the anges from the table = 2btff = 4:7 65 = 10:8 > p 65 = p p = p 36 Fy and for the web:
hc = 41:8 =t w 640 = 107p 640 = p p = p 36 Fy
5. Check the Strength by correcting the factored moment Mu to include the self weight. Self weight of the beam W12X22 is 22 lb./ft. or 0.022 kip/ft
wD wu Mu Mn b Mn
= = = = =
0:2 + 0:022 = 0:222 1:2(0:222) + 1:6(0:8) = 1:55 (1:55)(20)2=8 = 77:3 3 (36) Mp = Zx Fy = (29:3) = 87:9 (12) p 0:90(87:9) = 79:1 > Mu
k/ft k/ft k.ft in ksi in/ft k.ft
k.ft
Therefore use W12X22 section. 6. We nally check for the maximum distance between supports.
in
Victor Saouma
Draft 10{10
Case 2: A572 Grade 65 Steel:
1. same as in case 1 2. same as in case 1 76(12) u 3. Required Zx = M b Fy = 0:90(65) = 15:6 (14)(12) approximated by wd 9 = 9 = 18:7. 4. Check compact section limits p : = = p = p =
in
in
Note that Zx is
Not Good
In this case the controlling limit state is local buckling of the ange. Since p < < r , as above, the section is classi ed as non-compact. 5. Check the strength: Since the section is non-compact, the strength is obtained by interpolation between Mp and Mr . For the anges:
141 = p 141 = 19:0 pF 65;10 y ;10 p Mn = Mp ; (Mp ; Mr )( r; ; p ) Mp
r =
Mp Mr Mn b Mn
= = = =
(65) ZxFy = (17:4) = 94:2 (12) 3 (14 : 9) (65 ;10) = 68:3 Sx (Fy ; Fr ) = (12) 8:8;8:1 = 92:5 94:2 ; (94:2 ; 68:3) 19 :0;8:1p 0:90(92:5) = 83:25 > Mu
in
ksi in
in/ft
k.ft
ksi
in/ft
k.ft
k.ft
k.ft
Victor Saouma
Draft
Chapter 11
Recalling that concrete has a tensile strength (ft0 ) about one tenth its compressive strength (fc0 ), concrete by itself is a very poor material for exural members. 2 To provide tensile resistance to concrete beams, a reinforcement must be added. Steel is almost universally used as reinforcement (longitudinal or as bers), but in poorer countries other indigenous materials have been used (such as bamboos). 3 The following lectures will focus exclusively on the exural design and analysis of reinforced concrete rectangular sections. Other concerns, such as shear, torsion, cracking, and de ections are left for subsequent ones. 4 Design of reinforced concrete structures is governed in most cases by the Building Code Requirements for Reinforced Concrete, of the American Concrete Institute (ACI-318). Some of the most relevant provisions of this code are enclosed in this set of notes. 5 We will focus on determining the amount of exural (that is longitudinal) reinforcement required at a given section. For that section, the moment which should be considered for design is the one obtained from the moment envelope at that particular point.
11.1.1 Notation
6
Draft 11{2
As b c d fc0 fr0 fs0 ft0 fy h
Area of steel Width Distance from top of compressive bers to neutral axis Distance from the top of the compressive bers to the centroid of the reinforcement Concrete compressive strength Concrete modulus of rupture Steel stress Concrete tensile strength Steel yield stress (equivalent to Fy in AISC) Height s Steel ratio, A bd
A reinforced concrete beam is a composite structure where concrete provides the compression and steel the tension. 8 Failure is initiated by, Fig. 11.5:
Steel Yielding
Concrete Crushing
Figure 11.1: Failure Modes for R/C Beams 1. Yielding of the steel when the steel stress reaches the yield stress (fs = fy ). This occurs if we do not have enough reinforcement that is the section is under-reinforced. This will result in excessive rotation and deformation prior to failure. 2. Crushing of the concrete, when the concrete strain reaches its ultimate value ("c = "u = 0:003), ACI 318: 10.2.3. This occurs if there is too much reinforcement that is the section is overreinforced. This is a sudden mode of failure.
9 Ideally in an optimal (i.e. most e cient use of materials) design, a section should be dimensioned such that crushing of concrete should occur simultaneously with steel yielding. This would then be a balanced design. 10 However since concrete crushing is a sudden mode of failure with no prior warning, whereas steel yielding is often accompanied by excessive deformation (thus providing ample warning of an imminent failure), design codes require the section to be moderately under-reinforced.
Victor Saouma
11{3
Analysis: Given a certain design, determine what is the maximum moment which can be applied. Design: Given an external moment to be resisted, determine cross sectional dimensions (b and h) as
well as reinforcement (As ). Note that in many cases the external dimensions of the beam (b and h) are xed by the architect. We often consider the maximum moment along a member, and design accordingly.
Compatibility
Equilibrium
C d
T=C M_ext=Cd
Figure 11.2: Internal Equilibrium in a R/C Beam 1. Equilibrium: of forces and moment at the cross section. 1) Fx = 0 or Tension in the reinforcement = Compression in concrete and 2) M = 0 or external moment (that is the one obtained from the moment envelope) equal and opposite to the internal one (tension in steel and compression of the concrete). 2. Material Stress Strain: We recall that all normal strength concrete have a failure strain u = :003 in compression irrespective of fc0 .
14
Compatibility of Displacements: Perfect bond between steel and concrete (no slip). Note that those
two materials do also have very close coe cients of thermal expansion under normal temperature. Plane section remain plane ) strain is proportional to distance from neutral axis.
Victor Saouma
Draft 11{4
11.2.1 Equivalent Stress Block
10.2.6
17 In determining the limit state moment of a cross section, we consider Fig. 11.3. Whereas the strain distribution is linear (ACI-318 10.2.2), the stress distribution is non-linear because the stress-strain curve of concrete is itself non-linear beyond 0:5fc0 . 18 Thus we have two alternatives to investigate the moment carrying capacity of the section, ACI-318:
1. Use the non-linear stress distribution. 2. Use a simpler equivalent stress distribution.
19
The ACI code follows the second approach. Thus we seek an equivalent stress distribution such that: 1. The resultant force is equal 2. The location of the resultant is the same. We note that this is similar to the approach followed in determining reactions in a beam subjected to a distributed load when the load is replaced by a single force placed at the centroid.
Victor Saouma
11{5
It was shown that the depth of the equivalent stress block is a function of fc0 :
1
= :85 if fc0 4 000 1 0 = :85 ; (:05)(fc ; 4 000) 1 000 if 4 000 < fc0 < 8 000
(11.3)
Next we seek to determine the balanced steel ratio b such that failure occurs by simultaneous yielding of the steel fs = fy and crushing of the concrete "c = 0:003, ACI-318: 10.3.2 We will separately consider the two failure possibilities: Tension Failure: we stipulate that the steel stress is equal to fy :
s = A bd 0 As fy = :85fcab = :85fc0 b 1 c
y ) c = 0:85f f0 d c 1
(11.4)
Compression Failure: where the concrete strain is equal to the ultimate strain From the strain
diagram
"c = 0:003
c :003 d = :003+"s
)c=
9 > = >
d fs Es + :003
:003
(11.5)
22
Balanced Design is obtained by equating Eq. 11.4 to Eq. 11.5 and by replacing by b and fs by fy :
0 0:85fc
fy
d = fs:003 d Es +:003 fs = fy
=
b
ksi
we obtain
b = :85 1 f c 87 000 + f y y
f 0 87 000
(11.6)
This b corresponds to the only combination of b, d and As which will result in simultaneous yielding of the steel and crushing of the concrete, that is an optimal design.
Victor Saouma
Draft 11{6
< :75 b
24
23 Because we need to have ample warning against failure, hence we prefer to have an under-reinforced section. Thus, the ACI code stipulates:
(11.7)
In practice, depending on the relative cost of steel/concrete and of labour it is common to select lower values of . If < 0:5 b (thus we will have a deeper section) then we need not check for de ection. 25 A minimum amount of reinforcement must always be used to prevent temperature and shrinkage cracks: 200 (11.8)
min
fy
26
MD = Mn > Mu
= b = 0:9
(11.9)
11.2.3 Analysis
0
fc 87 2. b = (:85) 1 f y 87+fy 3. If act < b (that is failure is triggered by yielding of the steel, fs = fy )
s fy From Equilibrium a = :A 0b ; 85fc MD = As fy d ; a 2 s Combining this last equation with = A bd yields
)
s fy MD = As fy d ; 0:59 A f 0b
|
Mn
{z
MD =
(11.10)
4. y If act > b is not allowed by the code as this would be an over-reinforced section which would fail with no prior warning. However, if such a section exists, and we need to determine its moment carrying capacity, then we have two unknowns: (a) Steel strain "s (which was equal to "y in the previous case) (b) Location of the neutral axis c. We have two equations to solve this problem Equilibrium: of forces As fs (11.11) c = :85 f 0b
c 1
Victor Saouma
11{7
Strain compatibility: since we know that at failure the maximum compressive strain "c is equal
c = :003 d :003 + "s
Those two equations can be solved by either one of two methods: (a) Substitute into one single equation (b) By iteration Once c and fs = E"s are determined then
1c MD = As fs d ; 2
(11.12)
(11.13)
11.2.4 Design
27
We distinguish between two cases. The rst one has dimensions as well as steel area unknown, the second has the dimensions known (usually speci ed by the architect or by other constraints), and we seek As .
1. We start by assuming , at most = :75 b, and if de ection is of a concern (or steel too expensive), then we can select = 0:5 b with b determined from Eq. 11.6
MD =
y bd2 fy 1 ; :59 f 0 f c | {z } R
or
y R = fy 1 ; :59 f fc0
(11.14)
which does not depend on unknown quantities1 . Then solve for bd2 :
D bd2 = MR
(11.15)
3. solve for b and d (this will require either an assumption on one of the two, or on their ratio). 4. As = bd
1
Victor Saouma
Draft 11{8
y b, d and Md known, As unknown: In this case there is no assurance that we can have a design
with b . If the section is too small, then it will require too much steel resulting in an over-reinforced section. We will again have an iterative approach 1. Since we do not know if the steel will be yielding or not, use fs . 2. Assume an initial value for a (a good start is a = d 5) 3. Assume initially that fs = fy 4. Check equilibrium of moments ( M = 0)
M D ; fs d ; a 2 5. Check equilibrium of forces in the x direction ( Fx = 0) s fs a = :A 85fc0 b 6. Check assumption of fs from the strain diagram "s :003 d;c d ; c = c ) fs = Es c :003 < fy where c = a1 . As =
2:35 = :0102 s act = A bd = (10)(23) 0 p fc 87 = (:85)(:85) 4 87 = :02885 > act b = :85 1 fy 87+fy 60 87+60 s fy = (2:35)(60) = 4:147 in a = :A 0 b (:85)(4)(10) 85fc Mn = (2:35)(60)(23 ; 4:147 2 ) = 2 950 k.in MD = Mn = (:9)(2 950) = 2 660 k.in
in
Mn =
k.in
= 245
k.ft
Victor Saouma
11{9
Design a 15 ft beam to support a dead load of 1.27 k/ft, a live load of 2.44 k/ft using a 3,000 psi concrete and 40 ksi steel. Neglect beam weight
wu = 1:4(1:27) + 1:7(2 :44) = 5:92 2 2 (5 : 92) (15) MD = (12) = 2 000 0 8 87 fc = : 85 b 1 fy 87+fy 3 87 = 0:040 = (:85)(:85) 40 87+40 = :75 b = :75(0:04) = 0:030 y R = fy 1 ; :59 f 0 fc = (0:03)(40) 1: ; (0:59)(02:03) 40 3 = 0:917 2 000 M 2 d bd = R = (0:9)(0:917) = 2 423 3
k/ft k/ft ft in/ft k.in k.in in k in
ksi
423 = 15:57 . We thus adopt b = 10 Assume b = 10 , this will give d = 2 10 Finally, As = bd = (0:030)(10)(16) = 4:80 2 we select 3 bars No. 11
in in in
in
and d = 16
in
Solution:
Select the reinforcement for a cross section with b = 11:5 using fc0 = 3 and fy = 40
k.in ksi ksi in
in
in
= 2:47
in
= 3:38
in
4. We originally assumed a = 4, at the end of this rst iteration a = 3:38, let us iterate again with a = 3:30
Victor Saouma
Draft 11{10
5. Equilibrium of moments: 6. Check equilibrium of forces:
in
in
= 2:42
in
ksi in
= 3:3
in
7. we have converged on a. :42 8. Actual is act = (112 :5)(20) = :011 9. b is equal to 3 87 f 0 87 b = :85 1 f c 87 + f = (:85)(:85) 40 87 + 40 = :037
y y
10. max = :75 = (0:75)(0:037) = :0278 > 0:011 thus fs = fy and we use As = 2:42
in
Whereas coverage of continuous reinforced concrete beams is beyond the scope of this course, Fig. ?? illustrates a typical reinforcement in such a beam.
Victor Saouma
Victor Saouma
Cracks Cracks Reinforcement
Stirrups
Top bars
Stirrups
Bottom bars
Stirrups
Straight bar
11{11
Draft 11{12
where load combinations shall include both full value and zero value of L to determine the more severe condition, and U = 0:9D + 1:3W but for any combination of D, L, and W, required strength U shall not be less than Eq. (9-1). 9.3.1 - Design strength provided by a member, its connections to other members, and its cross sections, in terms of exure, axial load, shear, and torsion, shall be taken as the nominal strength calculated in accordance with requirements and assumptions of this code, multiplied by a strength reduction factor . 9.3.2 - Strength reduction factor shall be as follows: 9.3.2.1 - Flexure, without axial load 0.90 9.4 - Design strength for reinforcement Designs shall not be based on a yield strength of reinforcement fy in excess of 80,000 psi, except for prestressing tendons. 10.2.2 - Strain in reinforcement and concrete shall be assumed directly proportional to the distance from the neutral axis, except, for deep exural members with overall depth to clear span ratios greater than 2/5 for continuous spans and 4/5 for simple spans, a non-linear distribution of strain shall be considered. See Section 10.7. 10.2.3 - Maximum usable strain at extreme concrete compression ber shall be assumed equal to 0.003. 10.2.4 - Stress in reinforcement below speci ed yield strength fy for grade of reinforcement used shall be taken as Es times steel strain. For strains greater than that corresponding to fy , stress in reinforcement shall be considered independent of strain and equal to fy . 10.2.5 - Tensile strength of concrete shall be neglected in exural calculations of reinforced concrete, except when meeting requirements of Section 18.4. 10.2.6 - Relationship between concrete compressive stress distribution and concrete strain may be assumed to be rectangular, trapezoidal, parabolic, or any other shape that results in prediction of strength in substantial agreement with results of comprehensive tests. 10.2.7 - Requirements of Section 10.2.5 may be considered satis ed by an equivalent rectangular concrete stress distribution de ned by the following: 10.2.7.1 - Concrete stress of 0:85fc0 shall be assumed uniformly distributed over an equivalent compression zone bounded by edges of the cross section and a straight line located parallel to the neutral axis at a distance (a = 1 c) from the ber of maximum compressive strain. 10.2.7.2 - Distance c from ber of maximum strain to the neutral axis shall be measured in a direction perpendicular to that axis. 10.2.7.3 - Factor 1 shall be taken as 0.85 for concrete strengths fc0 up to and including 4,000 psi. For strengths above 4,000 psi, 1 shall be reduced continuously at a rate of 0.05 for each 1000 psi of strength in excess of 4,000 psi, but 1 shall not be taken less than 0.65. 10.3.2 - Balanced strain conditions exist at a cross section when tension reinforcement reaches the strain corresponding to its speci ed yield strength fy just as concrete in compression reaches its assumed ultimate strain of 0.003. 10.3.3 - For exural members, and for members subject to combined exure and compressive axial load when the design axial load strength ( Pn ) is less than the smaller of (0:10fc0 Ag ) or ( Pb ), the ratio of reinforcement p provided shall not exceed 0.75 of the ratio b that would produce balanced strain conditions for the section under exure without axial load. For members with compression reinforcement, the portion of b equalized by compression reinforcement need not be reduced by the 0.75 factor. 10.3.4 - Compression reinforcement in conjunction with additional tension reinforcement may be used to increase the strength of exural members. 10.5.1 - At any section of a exural member, except as provided in Sections 10.5.2 and 10.5.3, where positive reinforcement is required by analysis, the ratio provided shall not be less than that given by = 200
min
fy
Victor Saouma
Draft
Chapter 12
PRESTRESSED CONCRETE
12.1 Introduction
1
Beams with longer spans are architecturally more appealing than those with short ones. However, for a reinforced concrete beam to span long distances, it would have to have to be relatively deep (and at some point the self weight may become too large relative to the live load), or higher grade steel and concrete must be used. 2 However, if we were to use a steel with fy much higher than 60 ksi in reinforced concrete (R/C), then to take full advantage of this higher yield stress while maintaining full bond between concrete and steel, will result in unacceptably wide crack widths. Large crack widths will in turn result in corrosion of the rebars and poor protection against re. 3 One way to control the concrete cracking and reduce the tensile stresses in a beam is to prestress the beam by applying an initial state of stress which is opposite to the one which will be induced by the load. 4 For a simply supported beam, we would then seek to apply an initial tensile stress at the top and compressive stress at the bottom. In prestressed concrete (P/C) this can be achieved through prestressing of a tendon placed below the elastic neutral axis. 5 Main advantages of P/C: Economy, de ection & crack control, durability, fatigue strength, longer spans. 6 There two type of Prestressed Concrete beams: Pretensioning: Steel is rst stressed, concrete is then poured around the stressed bars. When enough concrete strength has been reached the steel restraints are released, Fig. 12.1. Postensioning: Concrete is rst poured, then when enough strength has been reached a steel cable is passed thru a hollow core inside and stressed, Fig. 12.2.
12.1.1 Materials
7
P/C beams usually have higher compressive strength than R/C. Prestressed beams can have fc0 as high as 8,000 psi. 8 The importance of high yield stress for the steel is illustrated by the following simple example. If we consider the following:
Draft 12{2
Vertical bulkhead Harping hold-up point Harping hold-down point
PRESTRESSED CONCRETE
Anchorage
Jacks
Continuous tendon
Casting bed
Jacks
Support force
Hold-down force
Casting bed
Tendon
Anchorage
Intermediate diaphragms
Anchorage Jack
Beam
Jack
Tendon in conduct
Wrapped tendon
Victor Saouma
12{3
1. An unstressed steel cable of length ls 2. A concrete beam of length lc 3. Prestress the beam with the cable, resulting in a stressed length of concrete and steel equal to 0 = lc 0. ls 4. Due to shrinkage and creep, there will be a change in length
(12.1)
6. The total steel elongation is "s ls = 1:03 10;3ls 7. The creep and shrinkage strains are about "cr + "sh ' :9 10;3 8. The residual stres which is left in the steel after creep and shrinkage took place is thus (1:03 ; :90) 10;3(29 103) = 4
ksi ksi
we want to make sure that this amout of deformation is substantially smaller than the stretch of the steel (for prestressing to be e ective). ;3 = 5. Assuming ordinary steel: fs = 30 , Es = 29 000 , "s = 2930 000 = 1:03 10
ksi ksi in in
(12.2)
ksi
;4 Thus the total loss is 30 30 = 87% which is unacceptably too high. 9. Alternatively if initial stress was 150 after losses we would be left with 124 10. Note that the actual loss is (:90 10;3)(29 103 ) = 26 in each case
ksi
or a 17% loss.
Having shown that losses would be too high for low strength steel, we will use Strands usually composed of 7 wires. Grade 250 or 270 ksi, Fig. 12.3.
0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 0000000 1111111 000000 111111 0000000 1111111 0000000 1111111 000000 111111 000000 111111 000000 111111 0000000 1111111 0000000 1111111 000000 111111 000000 111111 000000 111111 0000000 1111111 0000000 1111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 0000000 1111111 000000 111111 000000 111111 000000 111111 000000 111111 0000000 1111111 000000 111111 000000 111111 000000 111111 0000000 1111111 000000 111111 0000000 1111111 000000 111111 0000000 1111111 000000 111111 0000000 1111111 000000 111111 0000000 1111111 000000 111111 0000000 1111111 000000 111111 0000000 1111111 000000 111111 0000000 1111111 111111 000000 0000000 1111111
Tendon have diameters ranging from 1/2 to 1 3/8 of an inch. Grade 145 or 160 ksi. Wires come in bundles of 8 to 52.
Note that yield stress is not well de ned for steel used in prestressed concrete, usually we take 1% strain as e ective yield. 10 Steel relaxation is the reduction in stress at constant strain (as opposed to creep which is reduction of strain at constant stress) occrs. Relaxation occurs inde nitely and produces signi cant prestress loss. If we denote by fp the nal stress after t hours, fpi the initial stress, and fpy the yield stress, then
(12.3)
Victor Saouma
Draft 12{4
12.1.2 Prestressing Forces
11
PRESTRESSED CONCRETE
Prestress force \varies" with time, so we must recognize 3 stages: 1. Pj Jacking force. But then due to (a) friction and anchorage slip in post-tension (b) elastic shortening in pretension is reduced to: 2. Pi Initial prestress force But then due to time dependent losses caused by (a) relaxation of steel (b) shrinkage of concrete (c) creep of concrete is reduced to: 3. Pe E ective force
12.1.3 Assumptions
12
The following assumptions are made 1. Materials are both in the elastic range 2. section is uncracked 3. sign convention: +ve tension, ;ve compression 4. Subscript 1 refers to the top and 2 to the bottom 5. I S1 = cI1 S2 = cI2 6. e + ve if downward from concrete neutral axis
Through proper arrangement of the tendon (eccentricity at both support and midspan) various internal exural stress distribution can be obtained, Fig. 12.4.
The load-deformation curve for a prestressed concrete beam is illustrated in Fig. 12.6.
Victor Saouma
12{5
Q P 2Q P
h/2
fc 00 11 11 00 00 11 00 11 00 11 fc
fc 000 111 111 000 000 111 000 111 000 111 fc =f t
2f c 00 11 11 00 00 11 00 11 00 11
2h/3
2f c 0 11 00 0000000 1111111 00 11 0000000 00 +1111111 11 0000000 = 1111111 00 11 0000000 1111111 00 1111111 11 0000000 2f c 2f =2f t c 0 2f c 11 00 0000000 1111111 00 11 0000000 1111111 00 + 11 0000000 = 1111111 00 11 0000000 1111111 00 1111111 11 0000000 2f c 2f t =2f c fc Midspan 000 111 000 + 111 = 0 000 111 000 111 000 111 Ends fc 0 00 11 00 11 00 11 00 11 00 11 2f c
2f c 11 00 00 11 00 11 00 11 00 11 0 2f c 11 00 00 11 00 11 00 11 00 11 0 fc 00 11 00 11 00 11 00 11 00 11 fc fc 11 00 00 11 00 11 00 11 00 11 fc fc 11 00 00 11 00 11 00 11 00 11 fc
2Q P
h/3
P
h/2
Q P
h/2 h/3
f c 111 000 000 111 000 111 000 111 000 111 ft =f c
fc 00 11 00 11 00 11 00 11 00 11 fc
Midspan + 0 Ends =
Figure 12.4: Alternative Schemes for Prestressing a Rectangular Concrete Beam, (Nilson 1978)
(12.4) (12.5)
2. Pi and the self weight of the beam M0 (which has to be acconted for the moment the beam cambers due to prestressing)
Service Load when the prestressing force was reduced from Pi to Pe beacause of the losses, and the
actual service (not factored) load is apllied 3. Pe and M0
Victor Saouma
Draft 12{6
Member
(a) P P P cos 2 P sin P sin P sin P cos (b) P P P cos P sin P sin P cos
PRESTRESSED CONCRETE
Equivalent load on concrete from tendon Moment from prestressing
(c) Pe P e P P Pe P
(d) P e
P sin
P sin
P cos
P cos
(e) P P P P cos
P sin
(f) P P None
(g) P P
Ultimate Steel yielding Service load limit including tolerable overload First cracking load Decompression Balanced Full dead load
cgs (f=0)
Ru
ptu
re
Overload
Tn
fcr
or higher
o D
pe pi
Figure 12.6: Load-De ection Curve and Corresponding Internal Flexural Stresses for a Typical Prestressed Concrete Beam, (Nilson 1978)
Victor Saouma
12{7
Pi Ac
c1 e c2
11111 00000 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111
Pi e c 1 Ic
Pi (1Ac
e c1 ) r2
111111111 000000000 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111
Stage 1
Pi Ac
Pi e c 2 Ic
Pi (1+ Ac
e c2 ) r2
Pi (1Ac
111111111 000000000 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111
e c1 ) r2
111 000 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111
Mo S1
Pi (1Ac
111111 000000 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111
e c1 Mo )r2 S1
Stage 2
Pi (1+ Ac
e c2 ) r2
Mo S2
Pi (1+ Ac
e c2 Mo )+ r2 S2
Pe (1Ac
e c1 Mo )r2 S1
000000 111111 111111 000000 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111
00000000000 11111111111 11111111111 00000000000 00000000000 11111111111 00000000000 11111111111 00000000000 11111111111 00000000000 11111111111 00000000000 11111111111 00000000000 11111111111 00000000000 11111111111 00000000000 11111111111 00000000000 11111111111 00000000000 11111111111 00000000000 11111111111 00000000000 11111111111 00000000000 11111111111 00000000000 11111111111
Md + Ml S1
111111 000000 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111
Pe (1Ac
e c1 Mt )r2 S1
Stage 4
Pe (1+ Ac
e c2 Mo )+ r2 S2
Md + Ml S2
Pe (1+ Ac
e c2 Mt )+ r2 S2
Figure 12.7: Flexural Stress Distribution for a Beam with Variable Eccentricity Maximum Moment Section and Support Section, (Nilson 1978)
17
Those (service) exural stresses must be below those speci ed by the ACI code (where the subscripts
Victor Saouma
Draft 12{8
fci fti fcs fts
PRESTRESSED CONCRETE
0 permitted concrete compression stress at initial stage :60fp ci 0 permitted concrete tensile stress at initial stage < 3 fci 0 permitted concrete compressive stress at service stage :45 fc p p permitted concrete p tensile stress at initial stage 6 fc0 or 12 fc0 Note that fts can reach 12 fc0 only if appropriate de ection analysis is done, because section would be cracked. 18 Based on the above, we identify two types of prestressing: Full prestressing (pioneered by Freysinet), no tensile stresses, no crack, but there are some problems with excessive camber when unloaded. Partial prestressing (pioneered by Leonhardt, Abeles, Thurliman), cracks are allowed to occur (just as in R/C), and they are easier to control in P/C than in R/C.
19
The ACi code imposes the following limits on the steel stresses in terms of fpu which is the ultimate strength of the cable: Pj < :80fpuAs and Pi < :70fpuAs . No limits are speci ed for Pe .
12" 4" 5" 2" 6" 24" 7" 6" 2" 5" 4"
7" 4"
r2
The section properties for this beam are Ic = 12 000 4 , Ac = 176 2 , S1 = S2 = 1 000 3 , I = 68:2 2 . =A Determine exural stresses at midspan and at support at initial and nal conditions. Solution:
in in in in
Pi 1 ; ec1 f1 = ; A r2 c f2
(12.12-a)
psi
000 (5:19)(12) = ;83 = ; 169 176 1 ; 68:2 Pi 1 + ec2 = ;A r2 c 000 (5:19)(12) = 1 837 = ; 169 176 1 + 68:21
(12.12-b) (12.12-c)
psi
(12.12-d)
Victor Saouma
12{9
2. Pi and the self weight of the beam M0 (which has to be acconted for the moment the beam cambers due to prestressing) (176) 2 (:150) = 3 = :183 (12.13-a) w0 = (144) 2= 2 2 M0 = (:183)(40) = 36:6 (12.13-b) 8 The exural stresses will thus be equal to: M0 = (36:6)(12 000) = 439 0 f1w2 = S (12.14) 1 000 12
psi
Pi 1 ; ec1 ; M0 f1 = ; A r2 S1 c
psi
(12.15-e) (12.15-f)
k
3. Pe and M0. If we have 15% losses, then the e ective force Pe is equal to (1 ; 0:15)169 = 144
note that ;71 and ;1 561 are respectively equal to (0:85)(;83) and (0:85)(;1 837) respectively. 4. Pe and M0 + MDL + MLL 2 MDL + MLL = (0:55)(40) = 110 (12.17) 8 and corresponding stresses 000) = 1 320 f1 2 = (110)(12 (12.18) 1 000 Thus, (12.19-a) f = ; Pe 1 ; ec1 ; M0 + MDL + MLL
k.ft psi
Victor Saouma
Ac
r2
S1
Draft 12{10
PRESTRESSED CONCRETE
= ;510 ; 1 320 = ;1 830 fcs = :45fc0 = ;2 700p Pe 1 + ec2 + M0 + MDL + MLL f2 = ; A r2 S2 c = ;1 122 + 1 320 = +198 p fts = 6 fc0 = +380p
psi psi
5. The stress distribution at each one of the four stages is shown below.
-1830 -83 -510 -522
4
+198
3
-1122
2
-1398
1
-1837
The historical Walnut Lane Bridge ( rst major prestressed concrete bridge in the USA) is made of three spans, two side ones with lengths of 74 ft and a middle one of length 160 feet. Thirteen prestressed cocnrete beams are placed side by side to make up a total width of 44 fet of roadway and two 9.25 feet of sidewalk. In between the beams, and cast with them, are transverse sti eners which connect the beams laterally, Fig. 12.8
20
2#
c1 = c2
Victor Saouma
in
:2) + (7)(61 12
in
12{11
80 ft CENTER LINE
9.25
44
ROAD
9.25
SIDEWALK
TRANSVERSE DIAPHRAGMS
7"
6-7"
SLOTS FOR CABLES
Victor Saouma
Draft 12{12
52" 8.9" 22.5" 7" 22.5"
PRESTRESSED CONCRETE
61.2"
6-7" = 79"
8.9"
Figure 12.9: Walnut Lane Bridge, Cross Section 1 277 103 = 32 329 S1 = S2 = I = c 39:5 3 1 277 I r2 = A = 1 35410 = 943: 2
in in
(12.20-e) (12.20-f)
12.3.2 Prestressing
22
Each beam is prestressed by two middle parabolic cables, and two outer horizontal ones along the anges. All four have approximately the same eccentricity at midspan of 2.65 ft. or 31.8 inch. 23 Each prestressing cable is made up 64 wires each with a diameter of 0.27 inches. Thus the total area of prestressing steel is given by: 2 2 Awire = (d=2)2 = 3:14( 0:276 (12.21-a) 2 ) = 0:0598 Acable = 64(0:0598) 2 = 3:83 2 (12.21-b) 2 2 Atotal = 4(3:83) = 15:32 (12.21-c)
in in in in in in
24
Whereas the ultimate tensile strength of the steel used is 247 ksi, the cables have been stressed only to 131 ksi, thus the initial prestressing force Pi is equal to Pi = (131) (15:32) 2 = 2 000 (12.22)
ksi in k
25
The losses are reported ot be 13%, thus the e ective force is Pe = (1 ; 0:13)(2 000) = 1 740
k
(12.23)
Victor Saouma
12{13
The self weight of the beam is q0 = 1:72 . 27 The concrete (density=.15 = 3 ) road has a thickness of 0.45 feet. Thus for a 44 foot width, the total load over one single beam is 1 (44) (0:45) (0:15) = 3 = 0:23 (12.24) qr tot = 13
ft ft k ft k/ft
Similarly for the sidewalks which are 9.25 feet wide and 0.6 feet thick: 1 (2)(9:25) (0:60) (0:15) = 3 = 0:13 qs tot = 13 (12.25) We note that the weight can be evenly spread over the 13 beams beacause of the lateral diaphragms. 29 The total dead load is qDL = 0:23 + 0:13 = 0:36 (12.26)
28
ft ft k ft k/ft k/ft
30
The live load is created by the tra c, and is estimated to be 94 psf, thus over a width of 62.5 feet this gives a uniform live load of 1 (0:094) =ft2 (62:5) = 0:45 wLL = 13 (12.27)
k ft k/ft
31
k/ft
(12.28)
Pi 1 ; ec1 f1 = ; A r2 c f2
= ; (21 Pi = ;A c (2 = ; 1
(12.29-a)
psi
106) 1 ; (31:8)(39:5) = 490: 354 943: ec 2 1 + r2 106) 1 + (31:8)(39:5) = ;3 445: 354 943:
(12.29-b) (12.29-c)
psi
(12.29-d)
2. Pi and the self weight of the beam M0 (which has to be acconted for the moment the beam cambers due to prestressing) 2 M0 = (1:72)(160) = 5 504 (12.30) 8
k.ft
psi
(12.31)
Victor Saouma
Draft 12{14
= fti = f2 =
PRESTRESSED CONCRETE
Pi 1 ; ec1 ; M0 f1 = ; A r2 S1 c
(12.32-a)
psi
(12.32-e) (12.32-f)
3. Pe and M0 . If we have 13% losses, then the e ective force Pe is equal to (1 ; 0:13)(2 106 ) = 1:74 106
Pe 1 ; ec1 ; M0 f1 = ; A r2 S1 c 6 (31:8)(39:5) ; 2 043: = ;1 616 10 = ; 1:74 1 354 1 ; 943: Pe 1 + ec2 + M0 f2 = A r2 S2 c 6 1 : 74 10 :5) + 2 043: = ;954: = ; 1 354 1 + (31:8)(39 943: MDL + MLL = (0:81)(160) = 2 592 8
000) = 962: f1 2 = (2 592)(12 32 329
2
(12.33-a)
psi
psi
(12.34) (12.35)
psi
Thus,
Pe 1 ; ec1 ; M0 + MDL + MLL f1 = ; A r2 S1 c = ;1 616 ; 962: = ;2 578: fcs = :45fc0 = ;2 700p Pe 1 + ec2 + M0 + MDL + MLL f2 = A r2 S
psi
psi
Victor Saouma
Draft
Chapter 13
Three-Hinges ARCHES
13.1 Theory
1
Solving for H
H = wL 8h
(13.2)
We recall that a similar equation was derived for arches., and H is analogous to the C ; T forces in a beam, and h is the overall height of the arch, Since h is much larger than d, H will be much smaller than C ; T in a beam. 5 Since equilibrium requires H to remain constant across thee arch, a parabolic curve would theoretically result in no moment on the arch section. 6 Three-hinged arches are statically determinate structures which shape can acomodate support settlements and thermal expansion without secondary internal stresses. They are also easy to analyse through statics.
Draft 13{2
M = w L /8
2
Three-Hinges ARCHES
L w=W/L
-C +T W/2 SAG = h
NOTE THAT THE "IDEAL" SHAPE FOR AN ARCH OR SUSPENSION SYSTEM IS EQUIVILENT TO THE DESIGN LOAD MOMENT DIAGRAM
Figure 13.1: Moment Resisting Forces in an Arch or Suspension System as Compared to a Beam, (Lin and Stotesbury 1981)
wL/2
H h H L R V = wL/2 V R R = V 2+ H
2
h H
2 /8h H = wL
L/2
Victor Saouma
13{3
An arch carries the vertical load across the span through a combination of axial forces and exural ones. A well dimensioned arch will have a small to negligible moment, and relatively high normal compressive stresses. 8 An arch is far more e cient than a beam, and possibly more economical and aesthetic than a truss in carrying loads over long spans. 9 If the arch has only two hinges, Fig. 13.3, or if it has no hinges, then bending moments may exist either at the crown or at the supports or at both places.
APPARENT LINE OF PRESSURE WITH ARCH BENDING EXCEPT AT THE BASE APPARENT LINE OF PRESSURE WITH ARCH BENDING INCLUDING BASE
M h V V
h M base
M crown L
M base
h H
H<H H<H V
Since H varies inversely to the rise h, it is obvious that one should use as high a rise as possible. For a combination of aesthetic and practical considerations, a span/rise ratio ranging from 5 to 8 or perhaps as much as 12, is frequently used. However, as the ratio goes higher, we may have buckling problems, and the section would then have a higher section depth, and the arch advantage diminishes. 11 In a parabolic arch subjected to a uniform horizontal load there is no moment. However, in practice an arch is not subjected to uniform horizontal load. First, the depth (and thus the weight) of an arch is not usually constant, then due to the inclination of the arch the actual self weight is not constant. Finally, live loads may act on portion of the arch, thus the line of action will not necessarily follow the arch centroid. This last e ect can be neglected if the live load is small in comparison with the dead load. p 2 2 V + H ), whereas at the crown 12 Since the greatest total force in the arch is at the support, (R = we simply have H , the crown will require a smaller section than the support.
APPARENT LINE OF PRESSURE WITH ARCH BENDING EXCEPT AT THE BASE APPARENT LINE OF PRESSURE WITH ARCH BENDING INCLUDING BASE
M h V V
h M base
M crown L
M base
h H
H<H H<H V
Figure 13.4: Arch Rib Sti ened with Girder or Truss, (Lin and Stotesbury 1981)
Victor Saouma
Draft 13{4
Example 13-25: Design of a Three Hinged Arch
Three-Hinges ARCHES
adapted from (Lin and Stotesbury 1981) A long arch 100 ft high and spanning 510 ft is to be designed for a garage and hotel building, using air rights over roads and highways.
100
Garage and hotel Building
510
It is necessary to determine preliminary dimensions for the size of the arch section. The arches are spaced 60 ft on centers and carry four-story loading totaling 27 k/ft along each arch.
Solution:
1. To the initial DL and LL of 27 k/ft we add the arch own weight estimated to be load, thus the total load is w = (1 + :25)27 = 33:7 33 2. We next determine the various forces: 2 (33)(510)2 H = wL 8h = 8(100) = 10 700 (33)(510) = 8 400 V = wL 2 = 2
k/ft k k
3. 4. 5.
6.
(13.4-c) If we use concrete- lled steel pipe for arch section, and selecting a pipe diameter of 6 ft with a thickness of 1/2 inch, then the steel cross sectional area is As = 2 rt = Dt = (3:14)(6) (12) = (0:5) = 113 2 (13.5) The concrete area is 2 (6)2 2 (144) 2 =ftsq = 4 070 2 = (3 : 14) (13.6) Ac = D 4 4 Assuming that the steel has an allowable stress of 20 ksi and the concrete 2.5 ksi (noting that the strength of con ned concrete can be as high as three times the one of fc0 ), then the load carrySteel Ac (113)(20)ksi = 2,260 k ing capacity of each component is Concrete As (4 070)(2:5)ksi = 10,180 k Total 12,440 kip which is o.k. for the crown section (H =10,700 k) but not quite for the abutments at R=13,600 k. This process of trial and error can be repeated until a satisfactory preliminary design is achieved. Furthermore, a new estimate for the arch self weight should be undertaken.
k ft in ft in in ft in in
R =
Victor Saouma
13{5
13.2.1 Geometry
13
The Salginatobel bridge, perhaps the most famous and in uential structure of Maillart is located in high up in the Swiss Alps close to Shuders. 14 It is a three hinged pedestrian bridge which crosses a deep valley with a most beautiful shape which blends perfectly with its surrounding, Fig. 13.5
20 ft 20 ft 20 ft 87.5 ft 87.5 ft 20 ft 20 ft 20 ft
42.6 ft
295 ft
The load supporting structure is the arch itself, whereas the bridge deck and the piers are transfering the vertical load into the arch. 16 The arch cross section is not constant, and can be idealized as in Fig. 13.6 17 The basic shape of the supporting structure is a three hinged arch as shown in Fig. 13.7 18 The arch is parabolic (which as we saw an the optimal shape which minimizes exure), and the cross section at the quarter point has an area of
ft
= 4 291
2
in
(13.7) (13.8)
AF = (0:62)(12:46) = 7:73 2 = 1 113 and the e ective depth of the section is d = 12:79 ft, Fig. 13.8.
20
ft
2=1
735
in
(13.9)
Victor Saouma
Draft 13{6
ACTUAL ARCH WITH CENTROID (DOTTED LINE)
Three-Hinges ARCHES
HINGE
ACTUAL SPRINGING HINGE CORK PAD CONCRETE HARD WOOD ACTUAL CROWN HINGE
IDEALIZATION
HINGE
IDEALIZATION
Victor Saouma
42.6 ft
13{7
295 ft
12.46 ft 0.62 ft
0.59 ft
0.62 ft
Victor Saouma
42.6 ft
Draft 13{8
13.2.2 Loads
21
Three-Hinges ARCHES
The dead load WD is assumed to be linearly distributed (even though it is greater where the arch is deeper, and the vertical members longer) and is equal to 1,680 kips, Fig. 13.9.
D (1 680) wD = W L = (295) = 5:7
k ft k/ft
(13.10)
w D = 5.7 k/ft WD = 1680 k
L = 295 ft
Figure 13.9: Salginatobel Bridge Dead Load, (Billington and Mark 1983) For the sake of simplicity we will neglect the snow load (which is actually negligible compared to the dead load). 23 The live load is caused by tra c, and we consider the case in which two trucks, each weighing 55 kips, are placed at the quarter-point, Fig. 13.10. This placement of the load actually corresponds to one of the most critical loading arrangement. The total vertical load is shown in Fig. 13.11
22
13.2.3 Reactions
24
Reactions are easily determined from equilibrium, Fig. 13.15 VD = 1 680 2 110 VL = 2 (+ ;) Mc (840)(147:5) ; (840)(73:75) ; HD (42:6)
= 840
k
Victor Saouma
13{9
P = 55 k
295 ft
Figure 13.10: Salginatobel Bridge Truck Load, (Billington and Mark 1983)
Victor Saouma
PLAN
ROADWAY
P = 55 k
Draft 13{10
Q D = 1680 k P = 55 k
Three-Hinges ARCHES
P = 55 k
B VB,D = 840 k
VB,L = 55 k
Figure 13.11: Salginatobel Bridge Total Vertical Load, (Billington and Mark 1983)
C
d=42.6 ft
H A
l/4=73.75 ft
V
l/2=147.5 ft
Figure 13.12: Salginatobel Bridge Reactions, (Billington and Mark 1983)
Victor Saouma
42.6 ft
13{11
The shear diagrams for the dead, live and combined load is shown in Fig. 13.13.
840 k 420 k
+
SHEAR FORCE
3L/4 L/4 L/2 420 k 295 ft 840 k 295 ft x 0
SHEAR FORCE
55 k
L/2
L -55 k
295 ft
SHEAR FORCE
0 - 420 k - 475 k
- 895 k 295 ft
Figure 13.13: Salganitobel Bridge Shear Diagrams, (Billington and Mark 1983)
26
At the quarter point the axial force can be expressed as: N = H cos + V sin (13.12) where d tan = 2 (13.13) L and = 16:1o at this location. The horizontal force for the dead and live loads was determined previously as 1 455 and 95 kips respectively, and the vertical forces are obtained from the shear diagram, thus qr = (;1 455) cos16:1o + (;420) sin 16:1o = ;1 514 ND (13.14-a) qr (13.14-b) NL = (;95) cos 16:1o + (;55) sin 16:1o = ;106 and at the crown where there is no vertical force (and = 0)
k k
cr = (;1 455) cos0o + (;420) sin 0o = ;1 455 ND cr = (;95) cos 0o + (;55) sin 0o = ;95 NL
k
(13.15-a) (13.15-b)
27 28
The uniform dead load will not produce a moment on the parabolic arch. The (point) live load will create a moment which can be decomposed into two parts, 1. Vertical load will cause a trapezoidal moment diagram, and the max moment is V = P L = 11o 295 = 4 050 ML 24 2 4
k.ft
(13.16)
H = Hd(x), since 2. The second is caused by the horizontal reaction, and the resulting moment is ML d varies parabolically, and H is constant, that second moment is parabolic with a peak value equal to V = Hdmax = (95)(32:6) = ;4 050 ML (13.17)
k.ft
Victor Saouma
Draft 13{12
at the quarter point
V = Hd = (95) 3(32:6) = ;3 040 ML 1=4 4
k.ft
Three-Hinges ARCHES
(13.18)
29
The overall bending moment diagram from the live loads is determined by simply adding those two components, Fig. 13.14.
P P
L/4
L/4
+
BENDING MOMENT
BENDING MOMENT
L/4
L/2 295 ft
x 3L/4 L
BENDING
MOMENT
295 ft
Figure 13.14: Salginatobel Bridge Live Load Moment Diagram, (Billington and Mark 1983)
30
We observe that the actual shape of the arch follows this bending moment diagram for one of the most critical live load case. 31 The maximum moment at midspan is
max = 4 050 ; 3 040 = 1 010 ML
k.ft
(13.19) (13.20)
which would produce internal forces in the upper and lower anges equal to: max (1 010) Fint = ML d = (12:8) = 79
k.ft ft k
The axial stresses at the springlines were determined to be ;1 680 and ;110 kips for the dead and live loads respectively. 2 , thus the axial stresses are 33 At the support the area of concrete is Ac = 2 240 ;(1 680) D (13.21-a) sp = (2 240) 2 1 000 = ;750 ;(110) L (13.21-b) sp = (2 240) 2 1 000 = ;49 (13.21-c) s spTotal = ;750 ; 49 = ;799
in k psi in k psi in psi
Victor Saouma
13{13
At the crown, we repeat the same calculations, where the axial force is equal to the horizontal component of the reactions ;(1 455) D (13.22-a) cr = (1 735) 2 1 000 = ;839 ;(95) L (13.22-b) cr = (1 735) 2 1 000 = ;55 (13.22-c) s cr Total = ;839 ; 55 = ;894
psi in psi
The stresses at the quarter point are determined next. Note that we must include the e ect of both axial and exural stresses ;(1 514) (79) ;(106) top (13.23-a) qr = (4 291) 2 1 000 + (4 291) 2 1 000 ; (1 113) 2 | {z } | {z } | {z }
35
k k k in in in
DeadLoad
= ;353 ; 25 ; 71 ;449 (79) ;(1 514) ;(106) bot qr = (4 291) 2 1 000 + (4 291) 2 1 000 (1 113) | {z } | {z }| {z
psi k k in in
AxialStresses
{z
LiveLoad
Flexural
(13.23-b)
in
(13.23-c)
DeadLoad
= ;353 ; 25 + 71 ;307
AxialStresses
psi
{z
LiveLoad
Flexural
(13.23-d)
INCOMPLETE
36
The issue of unsymmetrical live load on a sti ened or unsti ened arch was also addressed by Maillart. As discussed in (Billington 1979) and illustrated by Fig. 13.15
Victor Saouma
Draft 13{14
Three-Hinges ARCHES
wL
wL
wL
/10 wL
wL a wL Unstiffened Arch
wL a 2
wL a 2
Stiffened Arch
Victor Saouma
Draft
Chapter 14
BUILDING STRUCTURES
14.1 Introduction
1
) M=K( s s b- c b = c Semi-Flexible
Flexible
Rigid
Flexible that is a hinge which can transfer forces only. In this case we really have cantiliver action only. In a exible connection the column and beam end moments are both equal to zero, Mcol = Mbeam = 0. The end rotation are not equal, col = 6 beam. Rigid: The connection is such that beam = col and moment can be transmitted through the connection. In a rigid connection, the end moments and rotations are equal (unless there is an externally applied moment at the node), Mcol = Mbeam = 6 0, col = beam. Semi-Rigid: The end moments are equal and not equal to zero, but the rotation are di erent. beam = 6 6 0. Furthermore, the di erence in rotation is resisted by the spring Mspring = col , Mcol = Mbeam = Kspring ( col ; beam).
For vertical load across the beam rigid connection will reduce the maximum moment in the beam (at the expense of a negative moment at the ends which will in turn be transferred to the columns).
Draft 14{2
3
H H
BUILDING STRUCTURES
The advantages of a rigid connection are greater when the frame is subjected to a lateral load. Under those conditions, the connection will sti en the structure and reduce the amount of lateral de ection, Fig. 14.2.
PI
PI
PI
PI
PI
PI PI PI
Figure 14.2: Deformation of Flexible and Rigid Frames Subjected to Vertical and Horizontal Loads, (Lin and Stotesbury 1981)
4 Fig. 14.3 illustrates the deformation, shear, moment and axial forces in frames with di erent boundary conditions under both vertical and horizontal loads.
e= M P
(14.1)
The induced stresses can be decomposed into uniform (;P=L) (assuming a unit width) and linearly varying one ( = M=S ) and the end stresses are
min = max =
We note that the linearly varying stress distribution must satisfy two equilibrium requirements: F = 0, thus the neutral axis (where the stress is equal to zero) passes through the centroid of the section, and M = 0, i.e. Mint = Mext . max equals zero, then = P 7 If we seek the eccentricity ecr for which L
;P L+
;P L;
(14.2-a) (14.2-b)
Victor Saouma
14{3
Deformation
w/2 -w/2 w/2 w/2
Shear
Moment
M
Axial
a
h
b
POST AND BEAM STRUCTURE
P p M
w/2 -w/2
M w/2 w/2
c d
SIMPLE BENT FRAME p -M/L M
w/2 -w/2
M w/2 w/2
e f
p THREE-HINGE PORTAL -M/L M
-M/L
w/2
-w/2
M M/h
-M/L
g h
-M/h -M/L
w/2
w/2
p/2
w/2
-w/2
-M/L
i j
-0.36M/h
0.36M/h
-M/L
M/2
M/2 p/2
TWO-HINGE FRAME
w/2
-w/2
0.45M 0.55M
-0.68M/h
k l
RIGID FRAME
0.68M/h
-0.5M/L
M/4
M/4 p/2
-M/L
M/4
M/4
Figure 14.3: Deformation, Shear, Moment, and Axial Diagrams for Various Types of Portal Frames Subjected to Vertical and Horizontal Loads
Victor Saouma
-M/2L
p/2
p/2
M/2L
M/L
p/2
p/2
M/L
p/2
p/2
M/L
M/L
Draft 14{4
8
BUILDING STRUCTURES
L T=1 2 2
(14.3) (14.4) (14.5)
If we want this net tensile force to be equal and opposite to the compressive force, then T = 4L T = P L 2 L from the centroid = P applied at 3 A 2 Thus the net internal moment is L = 2 P 2 L = PL Mint = 2T 2 32 432 6
9 To satisfy the equilibrium equation, this internal moment must be equal and opposite to the external moment Mext = Pecr hence PL = Pe (14.6) } 6 | {zcr
|{z}
or
Mint
Mext
ecr = L 6
(14.7)
in other words to avoid tensile stresses on either side, the resultant force P must be placed within the midle third kernel, Fig. 14.4
L/2 L/2 L/3 L/3 e L/3 L/3 L/6 P L/3 L/3 L/3
L/2
L/2
L/3
P L/3 e
P/A + M/S = = = + +
Victor Saouma
14{5
1. Prestressed concrete beams: If the prestressing cable is within the kernel (i.e middle third), then there will not be any tensile stresses caused by prestressing alone. 2. Foundations: If the eccentricity is within the middle kernel, then we have compressive stresses only under the foundation and no undesirable uplift. 3. Buildings: If the eccentricity of the vertical load is within the middle third, all columns will be loaded under compression only.
Whereas exterior wall provide enclosure and interior ones separation, both of them can also have a structural role in trnsfering vertical and horizontal loads. 13 Walls are constructed out of masonry, timber concrete or steel. 14 If the wall is braced by oors, then it can provide an excellent resitance to horizontal load in the plane of the wall (but not orthogonal to it). 15 When shear-walls subsytems are used, it is best if the center of orthogonal shear resistance is close to the centroid of lateral loads as applied. If this is not the case, then there will be torsional design problems.
We consider a reinforced concrete wall 20 ft wide, 1 ft thick, and 120 ft high with a vertical load of 400 k acting on it at the base. As a result of wind, we assume a uniform horizontal force of 0.8 kip/ft of vertical height acting on the wall. It is required to compute the exural stresses and the shearing stresses in the wall to resist the wind load, Fig. 14.5. 1. Maximum shear force and bending moment at the base
16
(14.8-a)
k.ft
(14.8-b)
Victor Saouma
Draft 14{6
20 11111 00000 00000 11111 00000 11111 00000 11111 00000 11111 W 00000 11111 00000 40011111 k 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 00000 11111 V -f HORIZONTAL +f +F VERTICAL + FDL +140 + 740 PSI + 600 -F 2/(3d) 1
BUILDING STRUCTURES
w=0.8 k/ft
120
H=96 k; M =5760 k
Figure 14.5: Design of a Shear Wall Subsystem, (Lin and Stotesbury 1981) 2. The resulting eccentricity is (5 760) = eActual = M P (400)
ft
k.ft k
= 14:4
60
ft
(14.9)
thus there will be tension at the base. 4. The moment of inertia of the wall is
(14.10)
3 (1) (20) I = bh 12 = 12
ft k.ft ft
ft
= 667
ft
5. The maximum exural stresses will be Mc (5 760) (10) = (86:5) max = I = (667) 4
ft
ksf
psi
(96) (14.13) =V A = (1)(20) 2 = 4:8 = 33:3 A concrete with nominal shear reinforcement can carry at least 100 psi in shear, those computed shear streses are permissible.
k ksf psi ft
Victor Saouma
14{7
= ;140 (14.14-a)
psi
psi psi
(Tension) (Compression)
(14.15-a) (14.15-b)
11. The stress distribution is linear, compression at one end, and tension at the other. The length of the tension area is given by (similar triangles) x = 20 ) x = 460 (20) = 7:7 (14.17) 460 460 + 740 460 + 740
ft
9. The compressive stress of 740 psi can easily be sustained by concrete, as to the tensile stress of 460 psi, it would have to be resisted by some steel reinforcement. 10. Given that those stresses are service stresses and not factored ones, we adopt the WSD approach, and use an allowable stress of 20 ksi, which in turn will be increased by 4=3 for seismic and wind load, 4 (14.16) all = 3 (20) = 26:7
ksi
12. The total tensile force inside this triangular stress block is = 250 T=1 | {z } 2 (460) (7:7 12) (12)
ksi in in
(14.18)
width
13. The total amount of steel reinforcement needed is (250) = 9:4 2 (14.19) As = (26 :7) This amount of reinforcement should be provided at both ends of the wall since the wind or eartquake can act in any direction. In addition, the foundations should be designed to resist tensile uplift forces (possibly using piles).
k in ksi
Victor Saouma
Draft 14{8
20
BUILDING STRUCTURES
120
W 400 k
H=96 k
24
1.2
~1.6
V +FM -F
M
Figure 14.6: Trussed Shear Wall 2. If we now add the e ect of the 400 kip vertical load, the forces would be C = ; (400) 2 ; 288 = ;488 T = ; (400) 2 + 288 = 88
k k k k
60
(14.21-a) (14.21-b)
3. The force in the diagonal which must resist a base shear of 96 kip is (similar triangles)
(14.22)
4. The design could be modi ed to have no tensile forces in the columns by increasing the width of the base (currently at 20 ft).
Victor Saouma
14{9
With reference to Fig. 14.7, the reinforced concrete shaft is 20 ft square, 120 ft high, and with 1 ft
20 20
~ 20
w = 0.8 k/ft
H = 96 k 60
111111 000000 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111
120
N.A.
Figure 14.7: Design Example of a Tubular Structure, (Lin and Stotesbury 1981) thick walls. It is subjected to a lateral force of 0.8 k/ft. 1. Comparing this structure with the one analysed in Sect. 14.2.1.1 the total vertical load acting on the base is now increased to V = 4(400) = 1 600 (14.23) 2. As previously, the maximum moment and shear are 5 760 and 96 respectively. 3. The moment of inertia for a tubular section is 3 (20)(20)3 (18)(18)3 4 I = bd (14.24) 12 = 12 ; 12 = 4 600 4. The maximum exural stresses: MC = (5 760) (20=2) = 12:5 = 87 (14.25) fl = I (4 600) 4
k k.ft k ft k.ft ft ksf psi ft
=V A=
(96) 2(20)(1)
k ft
= 2:4
ksf
= 17
psi
(14.26)
6. The vertical load of 1,600 k produces an axial stress of P ;(1 600) ax = A = (4(20)(1) 2 = ;20
k ft
ksf
= ;140
psi
(14.27)
Victor Saouma
Draft 14{10
7. The total stresses are thus
1 2
BUILDING STRUCTURES
= ax + fl = ;140 + 87 = ;53 = ;140 ; 87 = ;227 (14.28-a) (14.28-b) (14.28-c)
psi psi
thus we do not have any tensile stresses, and those stresses are much better than those obtained from a single shear wall.
PI
Figure 14.8: A Basic Portal Frame, (Lin and Stotesbury 1981) 1. Each bay of a bent acts as a separate \portal" frame consisting of two adjacent columns and the connecting girder. 2. The point of in ection (zero moment) for all columns is at midheight 3. The point of in ection for all girders is at midspan. 4. For a multibay frame, the shears on the interior columns are equal and the shear in each exterior column is half the shear of an interior column. This method will be discussed in more details in the following section.
Despite the widespread availability of computers, approximate methods of analysis are justi ed by 1. Inherent assumption made regarding the validity of a linear elastic analysis vis a vis of an ultimate failure design.
Victor Saouma
14{11
Vertical loads are treated separately from the horizontal ones. We use the design sign convention for moments (+ve tension below), and for shear (ccw +ve). Assume girders to be numbered from left to right. In all free body diagrams assume positivee forces/moments, and take algeebraic sums.
Based on the rst assumption, all beams are statically determinate and have a span, Ls equal to 0.8 the original length of the girder, L. (Note that for a rigidly connected member, the in ection point is at 0.211 L, and at the support for a simply supported beam hence, depending on the nature of the connection one could consider those values as upper and lower bounds for the approximate location of the hinge). 33 End forces are given by Maximum positive moment at the center of each beam is, Fig. 14.9 1 2 2 2 2 M+ = 1 8 wLs = w 8 (0:8) L = 0:08wL (14.29)
Maximum negative moment at each end of the girder is given by, Fig. 14.9
2 w 2 M left = M rgt = ; w 2 (0:1L) ; 2 (0:8L)(0:1L) = ;0:045wL
(14.30)
Girder Shear are obtained from the free body diagram, Fig. 14.10
V lft = wL 2 V rgt = ; wL 2
(14.31)
Victor Saouma
Draft 14{12
w M
lft
BUILDING STRUCTURES
Mrgt Vrgt
Figure 14.9: Approximate Analysis of Frames Subjected to Vertical Loads Girder Moments
Pabove
Vrgti-1
Vlfti
Pbelow
Figure 14.10: Approximate Analysis of Frames Subjected to Vertical Loads Column Axial Forces
Victor Saouma
14{13
Column axial force is obtained by summing all the girder shears to the axial force transmitted by the
(14.32)
Column Moment are obtained by considering the free body diagram of columns Fig. 14.11
h/2
h/2
Mi-1lft
Vi-1rgt
Mirgt
Virgt
Vi-1lft
Li-1
Mcolbelow
Li h/2
h/2
Figure 14.11: Approximate Analysis of Frames Subjected to Vertical Loads Column Moments
bot ; M rgt + M lft M top = Mabove i i;1
M bot = ;top
(14.33)
Column Shear Points of in ection are at mid-height, with possible exception when the columns on
the rst oor are hinged at the base, Fig. 14.11
top V = Mh 2
(14.34)
Girder axial forces are assumed to be negligible eventhough the unbalanced column shears above and
below a oor will be resisted by girders at the oor.
Victor Saouma
Draft 14{14
14.3.2.1 Portal Method
35
BUILDING STRUCTURES
Low rise buildings under lateral loads, have predominantly shear deformations. Thus, the approximate analysis of this type of structure is based on 1. Distribution of horizontal shear forces. 2. Location of in ection points.
36
The portal method is based on the following assumptions 1. In ection points are located at (a) Mid-height of all columns above the second oor. (b) Mid-height of oor columns if rigid support, or at the base if hinged. (c) At the center of each girder. 2. Total horizontal shear at the mid-height of all columns at any oor level will be distributed among these columns so that each of the two exterior columns carry half as much horizontal shear as each interior columns of the frame.
Forces are obtained from Column Shear is obtained by passing a horizontal section through the mid-height of the columns at each oor and summing the lateral forces above it, then Fig. 14.12
37
H/2
H/2
Figure 14.12: Approximate Analysis of Frames Subjected to Lateral Loads Column Shear
V int = 2V ext
(14.35)
Column Moments at the end of each column is equal to the shear at the column times half the height
M top = V h 2 M bot = ;M top
(14.36)
Victor Saouma
14{15
Mcol
above
Mi-1rgt
Vi-1rgt
Milft
Vilft
Mirgt
Virgt
Vi-1lft
Li-1/2
Li-1/2
Mcolbelow
Li/2 h/2
Li/2
h/2
Figure 14.13: ***Approximate Analysis of Frames Subjected to Lateral Loads Girder Moment
Girder Moments is obtained from the columns connected to the girder, Fig. 14.13
above ; M below + M rgt Milft = Mcol col i;1
Mirgt = ;Milft
(14.37)
Girder Shears Since there is an in ection point at the center of the girder, the girder shear is obtained
by considering the sum of moments about that point, Fig. 14.13
M V lft = ; 2L
V rgt = V lft
(14.38)
Column Axial Forces are obtained by summing girder shears and the axial force from the column above, Fig. ??
Pabove
Vrgti-1
Vlfti
Figure 14.14: Approximate Analysis of Frames Subjected to Lateral Loads Column Axial Force
Pbelow
(14.39)
Example 14-26: Approximate Analysis of a Frame subjected to Vertical and Horizontal Loads Victor Saouma Structural Concepts and Systems for Architects
Draft 14{16
0.25K/ft
BUILDING STRUCTURES
15
K
12 9
0.50K/ft
13
14 11
14 16
30
10 2 3
Figure 14.15: Example Approximate Analysis of a Building Draw the shear, and moment diagram for the following frame. Solution:
20
30
24
Vertical Loads
1. Top Girder Moments
lft M12 cnt M12 rgt M12 lft M13 cnt M13 rgt M13 lft M14 cnt M14 rgt M14 2 = ;0:045w12L2 12 = ;(0:045)(0:25)(20) 2 2 = 0:08w12L12 = (0:08)(0:25)(20) lft = M12 2 = ;0:045w13L2 13 = ;(0:045)(0:25)(30) 2 2 = 0:08w13L13 = (0:08)(0:25)(30) lft = M13 2 = ;0:045w14L2 14 = ;(0:045)(0:25)(24) 2 2 = 0:08w14L14 = (0:08)(0:25)(24) lft = M14 2. Bottom Girder Moments 2 M9lft = ;0:045w9L2 9 = ;(0:045)(0:5)(20) cnt 2 2 M9 = 0:08w9 L9 = (0:08)(0:5)(20) M9rgt = M9lft lft = ;0:045w10 L2 = ;(0:045)(0:5)(30)2 M10 10 cnt M10 = 0:08w10 L2 = (0:08)(0:5)(30)2 10 rgt = M lft M10 11 lft = ;0:045w12 L2 = ;(0:045)(0:5)(24)2 M11 12 cnt = 0:08w12 L2 = M11 (0:08)(0:5)(24)2 12 rgt lft M11 = M12 3. Top Column Moments lft M5top = +M12 top bot M5 = ;M5 rgt + M lft = ;(;4:5) + (;10:1) M6top = ;M12 13 M6bot = ;M6top rgt + M lft = ;(;10:1) + (;6:5) M7top = ;M13 14 M7bot = ;M7top rgt = ;(;6:5) M8top = ;M14 bot M8 = ;M8top
=; = =; =; = =; =; = =; =; = =; =; = =; =; = =; =; = =; = =; = = =;
4:5 8:0 4:5 10:1 18:0 10:1 6:5 11:5 6:5 9:0 16:0 9:0 20:3 36:0 20:3 13:0 23:0 13:0 4:5 4:5 5:6 5:6 3:6 3:6 6:5 6:5
k.ft k.ft
k.ft
k.ft k.ft
Victor Saouma
14{17
=; = =; = = =; = =; 4:5 4:5 5:6 5:6 3:6 3:6 6:5 6:5
12 9
0.50K/ft
13
14 11
14 16
10 2 3
20
+8.0k -4.5
k
30
+18.0k
24
+11.5k
k
-4.5k
+16.0k
-6.5k -13.0k
+23.0k
-9.0k
-9.0k
-5.6k
+3.6k
+6.5k
+4.5k +4.5k
-5.6
-3.6k
-6.5k
Figure 14.16: Approximate Analysis of a Building Moments Due to Vertical Loads 5. Top Girder Shear
lft V12 rgt V12 lft V13 rgt V13 lft V14 rgt V14
= = = = = =
=; = =; = =;
k k k k
k k
Victor Saouma
Draft 14{18
6. Bottom Girder Shear
BUILDING STRUCTURES
V9lft V9rgt lft V10 rgt V10 lft V11 rgt V11
= = = = = = = = = = = = = =
K
;V9
;V10 ;V11
w9 L9 = (0:5)(20) 2 2 lft
= =; = =; = =;
k k k k k k
7. Column Shears
V5 V6 V7 V8 V1 V2 V3 V4
+3.75
top M5 ;4:5 = ; 0:64 k H5 = 14 2 2 top M6 ;5:6 = ; 0:80 k H6 = 14 2 2 top M7 3:6 = 0:52 k H = 14 top M8 6:5 = 0:93 k H8 = 14 2 2 top M1 ;4:5 = ; 0:56 k H1 = 16 2 2 top M2 ; 5 :6 = ; 0:70 k H = 16 top M3 3:6 H3 = 16 2 2 top M4 = 6:5 16 H 4 2 2 2 2 2 7 2 2
= =
K
0:46 0:81
+2.5K
+3.0
-2.5K +5.0
K
-3.75K +6.0
K
+7.5
-3.0K
-5.0K
-7.5K
-6.0K
-0.64K
-0.80K
+0.51K
+0.93K
-0.56K
-0.70K
+0.45K
+0.81K
Victor Saouma
14{19
= = = = 2:50 6:25 6:75 3:00 = = = =
P5 P6 P7 P8
= = = =
lft V12 rgt + V lft = ;(;2:50) + 3:75 ;V12 rgt + V13 lft ;V13 14 = ;(;3:75) + 3:00 rgt ;V14
k k k k
9. Bottom Column Axial Forces P1 = P5 + V9lft = 2:50 + 5:0 rgt + V lft = 6:25 ; (;5:00) + 7:50 P2 = P6 ; V10 rgt + V9lft = 6:75 ; (;7:50) + 6:0 P3 = P7 ; V11 rgt = 310 P4 = P8 ; V11 :00 ; (;6:00)
k k
= = = = = = = =
15 (2)(3) 2(V5 ) = (2)(2:5) 2(V5 ) = (2)(2:5) V5 15+30 (2)(3) 2(V1 ) = (2)(7:5) 2(V1 ) = (2)(2:5) V1
= = = = = = = = = =; = =; = =; = =;
k k k k k k k
;M5
;up M7top
17:5 17:5 35:0 35:0 35:0 35:0 17:5 17:5 60 60 120 120 120 120 60 60
= (15)(16) 2 =
(7:5)(16) 2
=; = =; = =; = =;
k.ft k.ft
Victor Saouma
Draft 14{20
BUILDING STRUCTURES
APROXVER.XLS
Victor E. Saouma
A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
E L1 20 0.25 0.5
Height 14 16
L2 L3 30 24 0.25 0.25 0.5 0.5 MOMENTS Bay 1 Bay 2 Bay 3 Col Beam Column Beam Column Beam Col Lft Cnt Rgt Lft Cnr Rgt Lft Cnt Rgt AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAA -10.1 18.0 -10.1AAAA AAAAAAAA AAAA AAAAAAAA AAAAA -4.5 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A -6.5 8.0 -4.5 AAAA 11.5 -6.5 AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA -4.5 AAAA -5.6 3.6 6.5 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA 4.5 AAAA 5.6 -3.6 -6.5 AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAA AAAA AAAA A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAA A AAAAAAAA AAAAAAAA AAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAA -20.3 36.0 -20.3AAAA AAAAAAAAAAAA AAAA AAAAAAAA AAAAA -9.0 16.0 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A -13.0 23.0 -13.0 AAAA -9.0 AAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAA A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA -4.5 AAAA -5.6 3.6 6.5 AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAA AA AAAAAAAA AAAA AAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAA AAA 4.5 AAAA 5.6 -3.6 -6.5 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA SHEAR Bay 1 Bay 2 Bay 3 Col Beam Column Beam Column Beam Col Lft Rgt Lft Rgt Lft Rgt AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAAAAAA AAAA A AAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAA AAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAA A AAAAAAAA AAAAAAAAAAAA -2.50 AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA -3.00 AAAAAAAA AAAAAAAA AAAAA 2.50AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA 3.75 AAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAA -3.75AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A 3.00 AAAA AAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAA AAAA AAAAAAAA AAAA AAAA A A AAAA AAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAA AAAAAAA AAAAAAAA AA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA -0.64 AAAA -0.80 0.52 0.93 AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAA A AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAA A AAAAAAAA AAAAAAAAAAAA -5.00 AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAAAAAA AAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA -6.00 AAAAAAAA AAAAAAAA AAAAA 5.00AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA 7.50 AAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAA -7.50AAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAA 6.00 AAAA AAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAA AAAA A A AAAA AAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAA AAAAAAA AAAAAAAA AA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA -0.56 AAAA -0.70 0.46 0.81 AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AXIAL FORCE Bay 1 Bay 2 Bay 3 Col Beam Column Beam Column Beam Col AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAA AAAA AAAA A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA 0.00 0.00 0.00 A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA 2.50 6.25 6.75 3.00 AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAA A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A 0.00 0.00 0.00 A AAAAAAAAAAAA AAAAAAAAAAAA AAAA AAAAAAAAAAAA AAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA 7.50 AAAA 18.75 20.25 9.00 AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
Victor Saouma
APROXVER.XLS
Victor E. Saouma
Victor Saouma
C D E F G H I J K L M N O P Q L1 20 0.25 0.5 L2 30 0.25 0.5 L3 24 0.25 0.5 =-0.045*D5*D3^2 =0.08*D5*D3*D3 =+D13 =-0.045*I5*I3^2 =0.08*I5*I3*I3 =+I13 =-0.045*N5*N3^2 =0.08*N5*N3*N3 =+N13 =-F13+I13+G12 =-G14 =-K13+N13+L12 =-L14 =-P13+Q12 =-Q14 =+D3*D5/2 =-D22 =+I3*I5/2 =-I22 =+N3*N5/2 =-N22 =2*G14/A5 =2*L14/A5 =2*Q14/A5 Bay 2 Beam 0 Column Beam 0 Column Bay 3 Beam 0 Col =-F20+I20 =-K20+N20 =-P20 0 0 0 =+G28-F22+I22 =+L28-K22+N22 =+Q28-P22
A 1 2 3 Height 4 14 5 16 6 7 8 9 10 11 12
Bay 2 Bay 3 Beam Column Beam Column Beam Col Lft Cnt Rgt AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAALft Cnr Rgt AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Lft Cnt Rgt AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA =-0.045*D4*D3^2 =0.08*D4*D3*D3 =+D10 =-0.045*I4*I3^2 =0.08*I4*I3*I3 =+I10 =-0.045*N4*N3^2 =0.08*N4*N3*N3 =N10 AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA A =+D10 =-F10+I10 =-K10+N10 =-P10 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAA A A AAAA AAAA AAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAA A=-Q11 AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAA AAAA AAAA =-C11 =-G11 =-L11 AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAA A
13 14 15
AAAA AAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAA AAAAAAAA AAAA A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAA AAAA AAAA A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A AAAA AAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAA AAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
=+D13+C12 =-C14
16 17 18 19 20 21
Bay 2 Bay 3 Beam Column Beam Column Beam Col Lft Rgt Lft Rgt Lft Rgt AAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAA AAAA A A A AAAAAAAAAAAAAAAAAAAAAAA=-I20 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA =+N3*N4/2 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA =+D3*D4/2 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA=-D20 AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA =-N20 AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAA=+I3*I4/2 AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A A A AAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA A =2*L11/A4 AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA =2*G11/A4 AAAA =2*C11/A4 A AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA=2*Q11/A4 AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAA A
22 23
24 25 26 27 28
AAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAA AAAAAAAAAAAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAA AAAAAAAA AAAAAAAA AAAA A A A AAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA A A A AAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAA AAAAAAAA AAAAAAAAA A AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAA AAAAAAAAAAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
=2*C14/A5
=+D20
29 30
AAAA AAA AAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAA AAAAAAAA AAAA A AAAA AAAA AAAA AAAA AAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A AAAA AAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAA AAAAAAAA AAAA A AAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA A AAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAA AAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
=+C28+D22
14{21
Draft 14{22
4. Top Girder Moments
lft M12 rgt M12 lft M13 rgt M13 lft M14 rgt M14
BUILDING STRUCTURES
= = = = = =
5. Bottom Girder Moments M9lft = M1top ; M5bot = 60 ; (;17:5) M9rgt = ;M9lft lft = M rgt + M top ; M bot = ;77:5 + 120 ; (;35) M10 6 9 2 rgt = ;M lft M10 10 lft = M rgt + M top ; M bot = ;77:5 + 120 ; (;35) M11 7 10 3 rgt lft M11 = ;M11 6. Top Girder Shear
lft V12 rgt V12 lft V13 rgt V13 lft V14 rgt V14
M5top lft ;M12 rgt M12 + M6top = ;17:5 + 35 lft ;M13 rgt M13 + M7top = ;17:5 + 35 lft ;M14
= =; = =; = =;
= =; = =; = =;
k k k k k k
Design Parameters On the basis of the two approximate analyses, vertical and lateral load, we now
seek the design parameters for the frame, Table 14.2.
(2)(77:5) = ;7:75 12 = ; 2M L9 = ; 20 = +V9lft = ;7:75 lft M10 (2)(77:5) = ;5:17 = ; 2L = ; 30 10 lft = +V10 = ;5:17 lft 2 M (2)(77 : 5) 11 = ; L11 = ; 24 = ;6:46 lft = +V11 = ;6:46 8. Top Column Axial Forces (+ve tension, -ve compression) lft P5 = ;V12 = ;(;1:75) rgt lft = ;1:75 ; (;1:17) = ;0:58 P6 = +V12 ; V13 rgt ; V lft = ;1:17 ; (;1:46) = 0:29 P7 = +V13 14 rgt P8 = V14 = ;1:46 9. Bottom Column Axial Forces (+ve tension, -ve compression) P1 = P5 + V9lft = 1:75 ; (;7:75) = 9:5 rgt + V lft = ;0:58 ; 7:75 ; (;5:17) = ;3:16 P2 = P6 + V10 rgt + V9lft = 0:29 ; 5:17 ; (;6:46) P3 = P7 + V11 = 1:58 10 rgt = ; P4 = P8 + V11 1:46 ; 6:46 = ;7:66
= = = = = =
M12 = ; (2)(17:5) = ;1:75 ; 2L 20 12 lft +V12 = ;1:75 lft 2 M (2)(17 : 5) 13 ; L13 = ; 30 = ;1:17 lft +V13 = ;1:17 lft 2 M (2)(17 : 5) 14 = ; = ;1:46 ; L14 24 lft +V14 = ;1:46
lft lft
V9lft V9rgt lft V10 rgt V10 lft V11 rgt V11
k k k k k k
Victor Saouma
14{23
15K 30K
12 9
13 10
14 11
14
16
20
30
24
+17.5K
+35K
+35K
+17.5K
+60K
-17.5K +120K
-35K +120K
-35K +60K
-17.5K
-60K
-120K
-60K
+17.5K +77.5K
-17.5K
-77.5K
-77.5K
-77.5K
Victor Saouma
Draft 14{24
BUILDING STRUCTURES
Portal Method
PORTAL.XLS
Victor E. Saouma
A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
F 3
I L1 20
PORTAL METHOD
# of Bays L2 L3 30 24 MOMENTS Bay 1 Bay 2 Bay 3 Col Beam Column Beam Column Beam Col Lft Rgt AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Lft Rgt AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Lft Rgt AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAA AAAAAAAAAAAA AAAA AAAAAAAAAAAA A 17.5 -17.5 AAAA A AAAAAAAAAAAA AAAAAAAA AAA 17.5 -17.5 AAAAAAAA AAAA 17.5 -17.5AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA 17.5 AAAA 35.0 35.0 17.5 AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAA -17.5 AAAA -35.0 -35.0 -17.5 AAAAAAAA AAAA AAAAAAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAA AAAA AAAAAAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAA 77.5 -77.5 AAAAAAAA AAAA 77.5 -77.5AAAAAAAA AAAAAAAA AAAAA 77.5 -77.5 AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAA AAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA A A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAAAAAA AAAA AAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA 60.0 AAAA 120.0 120.0 60.0 AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA -60.0 AAAA -120.0 -120.0 -60.0 AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA SHEAR Bay 1 Bay 2 Bay 3 Col Beam Column Beam Column Beam Col Lft Rgt Lft Rgt Lft Rgt AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA AAAA AAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAA -1.46 -1.46AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA -1.17 -1.17 A -1.75 -1.75 AAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA 2.50 AAAA 5.00 5.00 2.50 AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA 2.50 AAAA 5.00 5.00 2.50 AAAAAAAA AAAAAAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAA AAAAAAAA AAA AAAAAAAAAAAA AAAAAAAAAAAA A -7.75 -7.75 AAAA A AAAAAAAAAAAA AAAAAAAA AAA -5.17 -5.17 AAAAAAAA AAAA -6.46 -6.46AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAA AAAA AAAA AAAA AAAA A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAA AAAA 7.50 AAAA 15.00 15.00 7.50 AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAA AAAA AAAA AAAAAAAA AAAA AAAAAAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA 7.50 AAAA 15.00 15.00 7.50 AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AXIAL FORCE Bay 1 Bay 2 Bay 3 Col Beam Column Beam Column Beam Col AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAA AAA AAAA AAAA AAAAAAAAAAAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAA AAAAAAAA AAAA AAAAAAAA 0.00 0.00 0.00 A A AAAAAAAAAAAA AAAAAAAAAAAA AAA AAAAAAAAAAAA AAAA AAAAAAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAA AAAA AAAA AAAAAAAA A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA 1.75 -0.58 0.29 -1.46 AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA AAAA AAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAA AAAAAAAA AAAA AAAAAAAA AAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA 0.00 0.00 0.00 AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAA AAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA 9.50 AAAA -3.17 1.58 -7.92 AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA
H2
16 30 45 7.5 15
Victor Saouma
14{25
Portal Method
PORTAL.XLS
Victor E. Saouma
A 1
PORTAL METHOD
A A A A A A A A A AA A A A A A A A A A A A A A A A AA A A A A A A A A A A A MOMENTS A A A A AA A A A A A A A A A A A A A A A AA A A A A A A AAAAAAAAAAA A A A A A A AA A A A A A A A A2 A A A AA A A A A A Bay 1 Bay 2 AA Bay 3 A A A A A A A A A A A A AAAAAAAAAAA A A AA A A A A A A A A A A A A A A A A A A Force A Shear Col Beam Column Beam Column Beam Col 6 A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A A A Tot AInt A Rgt ARgt A Rgt H Lat. A Ext Lft Lft Lft 7 A A A A A A AAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A AAAAAAAA AAAA=+H9 AAAAAAAA AAA AAAAAAAA AAA =+N8+O9 AAAAAAAA AA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAA A A =-I8 AAAA =+J8+K9 =-M8 AAAA =-Q8 AAAA 8 AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAA AAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAA AAAAAAAA AAAAAAAA AAAA=+F9*B9/2 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AA =+K9 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA=+H9 AAAAAAAA AAAAAAAA AAAAAAAA AAAAA A=2*E9 9 AAAA H1AAAAAAAAAAAAAAAAAAAAAAAAAAAA 14 A 15 AAAA =+C9 =+D9/(2*$F$2) AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA =+E9*B9/2 A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAA=-K9 AAAAAAAAAAAAAAAAAAAAAAAAAA =+K10 AAAAAAAAAAAAAAAAAAAAAAAAAAA=+H10 A A 10 =-H9 AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AAAA AAAA AAAA AAAA AAAA AAA A A AAAA AAAA AAAA AAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A AAAAAAAA AAAA=+H12-H10 =-I11 AAAAAAAA AAA AAA =+O12-O10+N11 =-Q11 AAAAAAAA AA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A A 11 =+K12-K10+J11 =-M11 AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAA AA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAA AAAAAAAA AAAAAAAA AAAA=+F12*B12/2 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AA =+K12 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA=+H12 AAAAAAAA AAAAAAAA AAAAAAAA A A 12 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA H2 16 A30 =SUM($C$9:C12) A=+D12/(2*$F$2) =2*E12 =+E12*B12/2 AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAA AAAA=-K12 AAAAAAAA AA =+K13 AAAAAAAA AAA=+H13 AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A A 13 =-H12 AAAA AAAAAA AA AAAAAAA AAA A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A A A A A AA A A A A A A A A A A A AAAAAAAAAAAA A A A A A AA A A A A A A A A A A A A A SHEAR A A A A AA A A A A A A A A A A A A 14 A A A A A AA A A A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AA A A A A A A A A A A AA A A A A A A A 15 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Bay 1 Bay 2 AA Bay 3 A A A A A A A A A A A A A AA A A A A A A A A A A A A A A A A A A A 16 Col Beam Column Beam Column Beam Col A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A A A A A A A A A A A A 17 Lft Rgt Lft Rgt Lft Rgt A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAA =-2*Q8/Q$3 AA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A A A A A A 18 =-2*M8/M$3 =+M18AAAA =+Q18AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA=-2*I8/I$3 =+I18 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAA AA AAAAAAAA AAAAAAAA AAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAA=+F9 AAAAAAAAAAAAAAAAAAAAAAAAAA =+F9 AAAAAAAAAAAAAAAAAAAAAAAAAAA =+E9 A A A A A A 19 =+E9 AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAA=+K19 AAAAAAAAAAAAAAAAAAAAAAAAAA =+O19 AAAAAAAAAAAAAAAAAAAAAAAAAAA=+S19 A A A A A A 20 =+H19 AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAA=-2*I11/I$3 =+I21 AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA =-2*Q11/Q$3 AAAAAAAAAAAAAA A A A A A A 21 =-2*M11/M$3 =+M21AAAA =+Q21AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAA AAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAA AAAA=+F12 AAAAAAAA AA =+F12 AAAAAAAA AAA =+E12 AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A A A A A A 22 =+E12 AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA A A A A A A AAAAAAAAAAAAAAAAAAAA=+K22 AAAAAAAAAAAAAAAAAAAAAAAAAA =+O22 AAAAAAAAAAAAAAAAAAAAAAAAAAA=+S22 A A A A A A 23 =+H22 AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAA AAAA A A A A A AA A A A A A A A A A A A A A A A A A AA A A A A A A A A A A A A A A A A A AA A A A A A A A A A A A A 24 AXIAL FORCE A A A A A AA A A A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AA A A A A A A A A A A AA A A A A A A A A A A AA A A A A A A A 25 Bay 1 Bay 2 AA Bay 3 A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A A A 26 Col Beam Column Beam Column Beam Col A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A A A AAAAAAAA AAAA0 AAAAAAAA AAA AAAAAAAA AAA 0 AAAAAAAA AA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A A A A A A 27 0 AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA AAAAAAAA AAAAAA AA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAA AAAAAAAA AAAAAAAA AAAA=+J18-M18 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AA =+N18-Q18 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAA=+R18 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAAA A AAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAA AAAAAAAAA AAAAAAAAAAAA 28 AAAAAAAAAAAAAAAAAAAAAAAAAAAA =-I18 AAAA AAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAA AAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA AAAAAAAAA A AAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAA AAAAAAAAA AAAAAAAAAAAA AAAAAAAA AAAA0 AAAAAAAA AAA AAAAAAAA AAA 0 AAAAAAAA AA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAA A A A A A A 29 0 AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A 30 =+H28-I21 A A A A A A AAAAAAAAAAAAAAAAAAAA=+K28+J21-M21 AAAAAAAAAAAAAAAAAAAAAAAAAA =+O28+N21-Q21 AAAAAAAAAAAAAAAAAAAAAAAAAAA=+S28+R21 A A A A A A AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAA A AAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAA A3 AL1 A AAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAA AAAAAAAAAAAAAA 2 AAAA # of Bays L2 L3 AAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAA AAAA AAAA A A A A A A A A AA A A A A AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAA AAAAAAA AAAAAAAA AAAA AAAAAAAAA A AAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAA A AAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A A A A A AA A A A A 3 30 A A A A A A20 A A AA A A A 24 A
A A A A A A A A A A A A A A
A A A A A A A A A A A A A A
A A A A A A
A A A A A A
A A A A A A
A A A A A
A A A A A
A A A A A A
A A A A A A
A A A A A A
A A A A A
AA AA AA AA AA AA
A A A A A A
A A A A A A
A A A A A
A A A A A A
A A A A A
A A A A A A
5 # of Storeys
Victor Saouma
Draft 14{26
BUILDING STRUCTURES
Mem. 1 2 3 4 5 6 7 8
Vert.
Hor.
Moment 4.50 60.00 Axial 7.50 9.50 Shear 0.56 7.50 Moment 5.60 120.00 Axial 18.75 15.83 Shear 0.70 15.00 Moment 3.60 120.00 Axial 20.25 14.25 Shear 0.45 15.00 Moment 6.50 60.00 Axial 9.00 7.92 Shear 0.81 7.50 Moment 4.50 17.50 Axial 2.50 1.75 Shear 0.64 2.50 Moment 5.60 35.00 Axial 6.25 2.92 Shear 0.80 5.00 Moment 3.60 35.00 Axial 6.75 2.63 Shear 0.51 5.00 Moment 6.50 17.50 Axial 3.00 1.46 Shear 0.93 2.50
Design Values 64.50 17.00 8.06 125.60 34.58 15.70 123.60 34.50 15.45 66.50 16.92 8.31 22.00 4.25 3.14 40.60 9.17 5.80 38.60 9.38 5.51 24.00 4.46 3.43
Victor Saouma
14{27 Values 86.50 16.00 12.75 97.70 36.00 12.67 90.50 23.00 12.46 22.00 8.00 4.25 27.60 18.00 4.92 24.00 11.50 4.46
In short structures (as with short beams), shear de ections, Fig. 14.23 dominates. For a concentrated load 1:2V h (14.40)
GA
2 E. 5
Victor Saouma
Draft 14{28
V
BUILDING STRUCTURES
000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111 000000000 111111111
WALL ELEVATION
Figure 14.23: Shear Deformation in a Short Building, (Lin and Stotesbury 1981)
Alternatively, in a tall building exural deformations, Fig. 14.24 are predominant. dominates.
111111 000000 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111 000000 111111
Figure 14.24: Flexural Deformation in a Tall Building, (Lin and Stotesbury 1981)
wh4 8EI
and the moment of inertia I = bh 12 for rectangular sections.
3
(14.41)
When two slender walls are connected by (heavy) lintels, the entire subsystem can be made to act as one cantilever supported by the foundations and de ections will be small. However if we have light lintels, their deformation is larger than those of the walls, Fig. 14.25.
Victor Saouma
14{29
L
0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111
111 000 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111
LINTEL BENDING
a
2 WALLS CONNECTED BY LINTELS
Figure 14.25: De ection in a Building Structure Composed of Two Slender Walls and Lintels, (Lin and Stotesbury 1981)
42
and
14.4.4 Frames
43
De ection of a rigid frame is essentially caused by shear between stories which produces vertical shears in the girders. From the portal method we can estimate those deformations, Fig. 14.26. 44 The deformation for the rst story at the exterior joint can be approximated from
VcolE h3 col = 12EI colE Vgdr L2h 2VcolE Lh2 gdr = 12EI = 12EI gdr gdr Vcol h2 totE = colE + gdr = 12E E
(14.44-a) (14.44-b)
h 2L IcolE + Ig dr
(14.44-c)
Victor Saouma
Draft 14{30
BUILDING STRUCTURES
DUE TO GI DUE TO CO
h STORIES
DEFORMATION OF ONE BE
Vcol h/2 L/2 h/2 Vcol MOMENT EQUILIBRIUM EXTERIOR JOINT V gdr (L/2)=Vcol (h) Vgdr V gdr
V col L/2 h/2 L/2 h/2 V INTERIOR JOINT Vgdr (L)=Vcol (h) Vgd
Figure 14.26: Portal Method to Estimate Lateral Deformation in Frames, (Lin and Stotesbury 1981)
45
VcolI h3 col = 12EI colI Vgdr L2 h 2VcolI Lh2 gdr = 12EI = 12EI gdr gdr V h2 col totI = colI + gdr = 12I E
tot tot = n 2
(14.45-a) (14.45-b)
h L IcolI + Ig dr
(14.45-c) (14.46)
where n is the number of stories, and tot is for either the interior or exterior joints. 46 The two major sources of lateral de ection are the bending of column in resisting horizontal shear and girders in resisting vertical shear, Fig. 14.27. 47 A vertical unsymmetric load will cause lateral de ection in frames, Fig. 14.28.
The cantilever de ection due to column shortening and lengthening (produced by overturning moment) is usually of secondary importance until the building is some 40 stories or higher,Fig. ??. 49 The total de ection at C is given by = PPL AE (14.47)
Victor Saouma
14{31
ELONGATION
SHORTENING
Figure 14.27: Shear and Flexural De ection of a Rigid Frame Subsystem, (Lin and Stotesbury 1981)
SIDE SWAY
Figure 14.28: Side-Sway De ection from Unsymmetrical Vertical Load, (Lin and Stotesbury 1981)
H1 H2 H3 H4 P1
H a
a
T C
Figure 14.29: Axial Elongation and Shortening of a Truss Frame, (Lin and Stotesbury 1981)
Victor Saouma
Draft 14{32
a Th t + c = 2 AE
BUILDING STRUCTURES
where: P is the force in any member due to loading on the whole system, L is the length of the member, A and E the corresponding cross sectional area and modulus of elasticity, P the force in the same member due to a unit (1) force applied in the direction of the de ection sought, and at the point in question. 50 Alternatively, we can neglect the web deformation and consider only the axial deformations in the colums: t + c h (14.48) (14.49)
Typical plan, elevation and oor section of a building are shown in Fig. 14.30. The lateral resiting
CORE SHAFT
111 000 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111 000 111
20 60
13@12=156
1111 0000 0000 1111 0000 1111 0000 1111 1111 0000 1111 0000
20"
60
20
156
MOMENT DIAGRAM
1111 0000 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111
CORE
W=4.8 K/FT
LOAD
5"
Figure 14.30: Transverse De ection, (Lin and Stotesbury 1981) elements are the center concrete shaft (20ft 40ft in section and made up of four 12-in walls) and the reinforced-prestressed concrete frames (made up of 12in 30in T beams, Igdr = 3:64 4 , and 20 inch square reinforced concrete columns). 52 We consider a wind load of 4.8 k/ft in the transverse direction and make the following assumptions: 1. Colums are of uniform sectional properties and height for all stories. 2. Shaft walls are of uniform thickness for all stories. We neglect wall openings. 3. The wind load is uniform over the height of the building.
ft
53
Victor Saouma
14{33
1. Determine the exural deformation of the top of the shaft (we may neglect shear deformations since the shaft is slender): (14.50-a) (14.50-b) (14.50-c) (14.50-d)
ft
(14.50-e) (14.50-f)
The h ratio is much less than 1/500 as permitted in most building codes, and s within the usual index for concrete buildings, which ranges between 1/1,000 and 1/2,500. If the wall thickness is reduced, and if door openings are considered, the de ection will be correspondingly smaller. The de ection due to moment increases rapidly at the top, the value of 1/1,800 indicates only the average drift index for the entire building, whereas the story drift index may be higher, especially for the top oor. 2. We next consider the de ection of the top of the frame. Assuming that each frame takes 1/9 of the total wind load and shear, and neglecting column shortening, then:
2 h 2L Eh = Vcol 12E IcolE + Ig dr 3 (20=12)(20=12)3 Icol = bh = 0:64 4 12 = 12 Igdr = 3:64 4 (156) = 41:7 =col ground = (4:8) Vcol I (2)(9) (12) + 2(60) (41:7) (12)2 = 12(432 000) (0:64) 4 (3:46) = 0:00116(18:8 + 34:7) = 0:062
ft ft k.ft ft k k ft ksf ft ft
(14.51-e) (14.51-f)
3. Since the story drift varies with the shear in the story, which decreases linearly to the top, the average drift will be 0:062=2 = 0:31 per story and the de ection at top of the building is approximately (14.52) = (13)(0:031) = 0:40 which indicates a drift ratio of (0:4) = 1 (14.53-a) Drift Ratio for Building = (156) 400 :062) = 1 Drift Ratio for Ground Floor = (0(12) (14.53-b) 194
ft ft ft ft ft ft
Victor Saouma
Draft 14{34
ft
BUILDING STRUCTURES
ft
4. Comparing the frame de ection of 0:40 with the shaft de ection of 0:087 , it is seen that the frame is about ve times more exible than the shaft. Furthermore, the frame would not be sti enough to carry all the lateral load by itlself. Proportioning the lateral load to the relative sti nesses, the frame would carry about 1/6 of the load, and the remaining 5/6 will be carried by the shaft. Increasing the column size will sti en the frame, but in order to be really e ective, the girder sti ness will also need to be increased, since thegirders contribute about 2/3 of the de ection. Then the frames can be made o carry a larger proportion of the load. Note that the de ected shapes of the shaft and the frames are quite di erent, so that the above simple comparison of top de ections is not an accurate assessment. Finally, we have not studied the e ect of the shaft sti ened by the exterior columns, which are rigidly connected to the shaft walls and will avt with the shaft as a unit, Fig. 14.31. This would
60 20 20 20
1111 0000 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 CORE 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111 0000 1111
+ +
COLUMNS PARTICIPATE
Figure 14.31: Frame Rigidly Connected to Shaft, (Lin and Stotesbury 1981) be quite e ective as the horizontal oor diaphragms will hold and force them to de ect together. 5. In summary, this appears to be quite an e cient layout, further analysis would re ne and optimize it.
Through strategically located havy trusses at the top and possibly at the middle of a building we can brace the exterior columns against the core shaft. This will result in a frame-like action in the shaft,
Victor Saouma
156
14{35
equalize temperature shortening of vertical components, and reduce lateral de ections, Fig. 14.32.
T TENSION COMPRESSION
CORE
WITH BRACING EFFECT
HEIGHT
TIEDOWN
TOTAL RESISTANCE ARM IS INCREASED BY COL. ACTION RESISTANCE ARM OF CORE SHAFT ONLY
DEFLECTION
Figure 14.32: E ect of Exterior Column Bracing in Buildings, (Lin and Stotesbury 1981)
Victor Saouma
Draft 14{36
BUILDING STRUCTURES
Victor Saouma
Draft
Bibliography
318, A. C.: n.d., Building Code Requirements for Reinforced Concrete, (ACI 318-83), American Concrete Institute. Anon.: xx, Envyclopaedia Brittanica, University of Chicago. Billington, D.: 1973, in D. Billington, R. Mark and J. Abel (eds), The Maillart Papers Second National Conference on Civil Engineering: History, Heritage and the Humanities, Department of Civil Engineering, Princeton University. Billington, D.: 1979, Robert Maillart's Bridges The art of Engineering, Princeton University Press. Billington, D.: 1985, The Tower and the Bridge, xx. Billington, D. and Mark, R.: 1983, Structural studies, Technical report, Department of Civil Engineering, Princeton University. Galilei, G.: 1974, Two New Sciences, Including Centers of Gravity and Forces of Percussion, University of Wisconsin Press, Madison, Wisc. S. Drake translation. le Duc, V.: 1977, Entretiens sur L'Architecture, Pierre Mardaga, Bruxelles, Belgique. Lin, T. and Stotesbury, S.: 1981, Structural Concepts and Systems for Architects and Engineers, John Wiley. Nilson, A.: 1978, Design of Prestressed Concrete, John Wiley and Sons. of Steel COnstruction, A. I.: 1986, Manual of Steel Construction Load and Resistance Factor Design, American Institute of Steel Construction. Palladio, A.: 19xx, The Four Books of Architecture, Dover Publications. Penvenuto, E.: 1991, An Introduction to the History of Structural Mechanics, Springer-Verlag. Schueller, W.: 1996, The design of Building Structures, Prentice Hall. Timoshenko, S.: 1982, History of Strength of Materials, Dover Publications. UBC: 1995, Uniform building code, Technical report, International COnference of Building O cials. Vitruvius: 1960, The Ten Books on Architecture, Dover.