Professional Documents
Culture Documents
Ruger Carbines
Ruger Carbines
Ruger Carbines
RUGER CARBINE
PC9, PC4, PC9GR & PC4GR
READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM
For Product Service on This Model Please Call: (520) 778-6555 (See p. 23)
G 4/01 R2
GUN
WARN ING
WILL
FIRE
H MAG
AZIN
E OUT
FIREARMS SAFETY-YOUR RESPONSIBILITY SAFETY MUST BE THE FIRST AND CONSTANT CONSIDERATION OF EVERY PERSON WHO HANDLES FIREARMS AND AMMUNITION.
This Instruction Manual is designed to assist you in learning how to use and care for your RUGER CARBINE properly. Please contact us if you have any questions about it. Only when you are certain you fully understand the Manual and can properly carry out its instructions should you practice loading, etc. with live ammunition. If you have any doubts about your ability to handle or use a particular type of gun safely, then you should seek supervised instruction. Such personalized instruction is often available from gun dealers, gun clubs or police departments. If none of these sources can help you, write to the National Rifle Association, 11250 Waples Mill Rd., Fairfax, VA 22030-7400. They will assist you. The person possessing a gun has a full-time job. You cannot guess; you cannot forget. You must know how to use your firearm safely. Do not use any firearm without having a complete understanding of its particular characteristics and safe use. Remember: There is no such thing as a foolproof gun.
TABLE OF CONTENTS
Page General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Operation of Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 The Slide Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Ammunition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 To Load and Fire (With Magazine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 To Load and Fire (Without Magazine) . . . . . . . . . . . . . . . . . . . . . . . . . . 11 To Unload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 To Extract and Eject a Chambered Cartridge . . . . . . . . . . . . . . . . . . . . . 13 To Clear a Malfunction (Jam) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 To Minimize Malfunctions (Jams) . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 To Disassemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Magazine Inspection and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Attaching Ruger Scope Rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Sight Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Ghost Ring Sight Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Service and Parts Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Parts Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 The Basic Rules of Safe Firearms Handling . . . . . . . . . . . . . . . . . . . . . . 31 Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
RUGER is a registered U.S. trademark.
Locking Devices Alterations Manual Safety Lead Exposure Ammunition Firing Handling
OTHER CAUTIONS AND WARNINGS APPEAR THROUGHOUT THE MANUAL. FIREARMS ARE DANGEROUS WEAPONS READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL THOROUGHLY AND CAREFULLY BEFORE USING.
! WARNINGALTERATIONS
This product was designed to function properly in its original condition. Alterations can make it unsafe. Do not alter any part or add or substitute parts or accessories not made by Sturm, Ruger & Co. Inc.
Because the bullet offers the least resistance, it moves out of the cartridge case and exits the muzzle. The bolt then moves rearward automatically, extracting and ejecting the fired cartridge case, and at the same time cocking the hammer and compressing the guide rod/recoil spring assembly, etc., as described above. Once the trigger is released, the rifle is ready to fire again. Each time the trigger is pulled and released, the same cycle is repeated until there are no more cartridges in the magazine or in the chamber. The rifle will fire if there is a cartridge in the chamber and the trigger is pulled, whether or not there is a magazine in place! Removing the magazine does not unload the rifle. Never assume the rifle is unloaded. Visually inspect the chamber and the magazine each time the rifle is handled to be certain there are no cartridges in either. All models have the same basic operating mechanism and include the following features with which the gun user should be thoroughly familiar.
NOMENCLATURE
Receiver Stock Slide Rear Sight Barrel
Slide Stop Magazine Latch Magazine Figure 1. In these illustrations the frequently used operating components are identified. Note that the safety is protruding fully from the right side of the trigger guard and is therefore in its on (safe) position.
OPERATION OF SAFETY
The RUGER CARBINE has a cross-button safety which is located in the rear portion of the trigger guard (Figure 1, p. 5). The safety is on when it protrudes fully from the right side (the cocking handle side) of the trigger guard, as shown in Figure 1, p. 5. In this position, the gun cannot be fired from a normal pull on the trigger. The safety should always be in the on (safe) position except when the shooter is actually firing the gun. The safety should be moved to the on position whenever the shooter ceases firing, even temporarily. The safety is off (fire) when it protrudes from the left side of the trigger guard, as shown in Figure 2. When the safety is off, the red band shows on the safety button, but do not totally rely on the appearance of the red band to indicate that the safety is off. In poor light or if dirt is present, the red band may not be visible. If the safety is off and the trigger is pulled, the rifle will fire if a cartridge is in the chamber.
Figure 2. The underside of the trigger guard section of the rifle. In this illustration the safety is shown in the off (fire) position. The position of the safety and red band indicate the safety is off.
The safety is held in its on or off position by a plunger that is under spring tension. When the safety is moved to either the on or off position, a distinct click should be heard. Frequently check the position of the safety to be certain the safety has not been inadvertently moved. If the safety seems to move too easily, or if the click is not heard when the safety is moved, the rifle should be discontinued from use and returned to the Prescott Product Service Department for repair (See page 23).
1
Press Up to Lock Slide Open
To release the slide: The slide can be released by drawing back slightly on the cocking handle and depressing the slide stop thumbpiece. When the slide is released, it will move forward under pressure from the recoil spring. The safety of the rifle should always be in the on position except when the user is actually firing at a selected target. When the last shot has been fired and the magazine is empty, the slide stop automatically holds the slide open. When there is an empty magazine in the rifle and the slide is retracted manually, the slide stop will have to be manually actuated to hold the slide open. If a loaded magazine is inserted in the rifle when the slide is closed and the slide is then retracted fully, the slide stop will not automatically hold open the slide. The user can actuate the slide stop mechanism to hold the slide open at any time by retracting the slide and pushing up the slide stop.
AMMUNITION
The RUGER CARBINE is chambered for, and designed to properly function with, only factory loaded 9mm Luger (Parabellum) or .40 Auto ammunition (standard, high velocity, +P, or +P+ ammunition) manufactured to U.S. industry standards. SPECIAL NOTE: The higher pressures produced by the .40 auto cartridge make the use of aluminum-cased .40 auto ammunition inadvisable in the Ruger Carbine or any other blowback -operated firearm. Occasional case separations and jamming of the mechanism may occur. This does not apply to locked-breech firearms such as the Ruger P-94 pistols. Use only such factory ammunition in good condition that exactly matches the caliber of your rifle that is rollmarked on the receiver.
WARNING AMMUNITION
Death, serious injury, and damage can result from the use of wrong ammunition, bore obstructions, powder overloads, or incorrect cartridge components. Always wear shooting glasses and hearing protectors.
5. Load the magazine by sliding up to 15* 9mm or 11* .40 Auto cartridges of the same caliber as that marked on the receiver of your rifle into the magazine. The Ruger CARBINE is designed to function properly only with correct Ruger magazines loaded with factory ammunition of the correct type and caliber loaded to U.S. industry specifications. 6. Insert magazine fully into the firearm, with bullet end of the cartridges toward the muzzle, until it is locked in place by the magazine latch. (Magazine cannot be seated if reversed).
* By Federal Law, newly manufactured magazines with a capacity of greater than 10 (ten) cartridges are designated For Law Enforcement Use Only and are only sold to law enforcement and government agencies. Commercially sold rifles are supplied with 10 round magazines only.
7. Load a cartridge into the chamber by fully retracting the cocking handle, pushing down the slide stop, and then releasing the cocking handle. The slide will forcibly move forward, chambering a cartridge from the magazine. Dont touch the trigger. Do not ride the cocking handle as it moves forward. Do not apply force to the cocking handle to chamber a cartridge. If a cartridge does not readily chamber, eject it from the rifle, hold the slide open with the slide stop, remove the magazine and see MALFUNCTION WARNING, p. 14. 8. The rifle is now fully loaded. If the rifle is not to be fired immediately, the safety should remain ON (See Figure 1, p. 5). When the safety is moved to the off position, the rifle will fire a cartridge each time the trigger is pulled until all the cartridges in the magazine, and the one in the chamber, have been fired. Firing will automatically reload and recock the rifle. Note that every time the trigger is pulled, if a cartridge is in the chamber and the safety is off, the rifle will fire be careful!
WARNING FIRING
The slide automatically opens and shuts quickly while firing. Keep face and hands away from it. Hot brass and powder gas is ejected quickly and can burn you. The rifle should be fired from the right shoulder. Always wear shooting glasses and hearing protectors.
10
! WARNING HANDLING
If dropped or struck with the safety off, the rifle may fire. Keep chamber empty unless actually firing! Keep safety on unless actually firing! ANY GUN MAY FIRE IF DROPPED
! WARNING UNLOADING
So that the rifle can be used as a single loader, it will fire whether or not a magazine is in the gun if a cartridge is chambered. Removing magazine does not unload rifle! To unload, first remove magazine, then pull slide to rear, eject chambered cartridge, and visually inspect chamber. The safety should always be in the on (safe) position when loading or unloading the rifle.
TO UNLOAD
NOTE: This sequence must be followed exactly as spelled out. Failure to do so can result in the rifles chamber becoming unintentionally loaded with a cartridge!
11
1. Keep the muzzle pointed in a safe direction at all times and keep the fingers outside the trigger guard. Move the safety to the on position. 2. Remove the magazine. Remember that even though the magazine has been removed, a cartridge remaining in the chamber can still be fired! 3. Retract the slide to its open position and hold it open by pressing the slide stop up. 4. Always visually double check the chamber to be certain it is empty. 5. The only safe rifle is one in which the slide is open, the chamber is empty, and there is no magazine in the gun.
4 3
1 2
6. Cartridges can be removed from the magazine by simply pushing them lightly downward and forward with the thumb, forefinger, or the rubber eraser end of a pencil against the base of the top cartridge. Do not use a loaded cartridge as a tool to strip cartridges from the magazine. 7. If desired, the slide can be left in the open position, being held there by the slide stop. If it is desired to close the slide, again look to be certain the chamber is empty. Keep the safety on, retract the slide to its rearmost position, push the thumbpiece of the slide stop down, and let the slide snap forward. Keep your fingers out of the receiver! 8. With the muzzle pointed in a safe direction, push the safety to the off position and pull the trigger to decock it. The rifle can be dry fired for practice as long as it is empty and pointed in a safe direction. 9. Push empty (unloaded) magazine into the rifle until the magazine latch locks it in place. If an empty magazine is inserted into a rifle with the slide held open, it will be necessary to press the bolt stop downward in order to close the slide.
12
13
2. If changing to another type or brand of cartridges does not at once eliminate malfunctions, then the following steps should be taken: a. Make certain the gun and the magazine are unloaded and that the safety is on. Remember, the magazine should be removed first, then check the chamber and be certain it and the magazine well are clear of cartridges. b. Thoroughly clean the magazine and slide mechanism, paying particular attention to removing accumulated grease. Use a bristle brush and solvent to remove grease and fouling from the slide, the extractor, the chamber, and the feed ramp. (See the Care and Cleaning section of this manual for detailed cleaning instructions). c. Check to see that the magazine spring tension is adequate and that the magazine follower moves freely up and down. d. Check the magazine lips to be certain they are free of nicks and burrs and are not deformed. e. Remove excess oil and solvent from all cleaned components, load the magazine, and try the firearm again. As always, proceed slowly. Be certain bystanders are not close and that you are wearing eye and hearing protection and that your face is a safe distance from the rifle so that any discharge resulting from a jammed cartridge will not injure anyone. If the above procedures do not result in a smooth and reliably functioning firearm, dont use the gun. The rifle can be returned directly to our Prescott, Arizona Service Department for repair. See the Service and Parts Policy section of this manual for packing and shipping information. Another precaution: When using any autoloading firearm, form the habit of examining fired cartridge cases. If they have bulged heads or frequently show splits on any part of the case, the rifle should be returned to the factory for inspection.
! WARNING MALFUNCTIONS
A cartridge fires when the firing pin impacts the primer, and also can be discharged before it is chambered if its primer receives a sharp blow. If a cartridge hangs up, jams, or binds when being chambered or when being fed from the magazine into the chamber, do not attempt to force it into the chamber by pushing or striking the cocking handle. Any jam or feeding problem is a signal to immediately stop using the gun until it can be determined what is wrong. Most failures of a cartridge to feed or to chamber are caused by a damaged magazine, improper gun handling, or defective ammunition. Whatever the cause, cartridge jams can result in the potentially dangerous situation of a cartridge discharging before it is chambered. If this occurs, the cartridge case will rupture and its fragments will fly out of the gun with sufficient force to cause injury. Always wear shooting glasses and hearing protectors! Keep face away from chamber!
WARNING DISASSEMBLY
4 3
1 2
TO DISASSEMBLE
Make Sure Gun Is Unloaded!
1. With the rifle pointing in a safe direction, remove the magazine. (See Fig. 4) 2. Remove screw and barrel band from front of stock. (See Fig. 4) It may be necessary to carefully spread the barrel band slightly apart with a screwdriver blade so that the band can be removed from its stock recess. Remove the take down screw and lock washer from the bottom of the stock. (See Fig. 4) 3. Lift front end of barrel/receiver assembly and remove it upward from stock. (See Fig. 5) Remove the receiver spacer from the inside of the stock (refer to parts list, p. 27, for applicable serial number range). 4. Pull slide assembly to rear far enough to expose a cross hole in the guide rod (about 1 3/4). Insert a pin/punch to hold slide in this position. (See Fig. 6) 2
2 1 3
15
5. Move slide/recoil spring assembly slightly forward to disengage guide rod and rotate it downward out of the receiver. The cocking handle and plunger will pop free. (See Fig. 7)
6. Handguard may be removed by carefully placing both thumbs at rear corners and slowly pushing upward; but this is not recommended for routine cleaning or maintenance. (See Fig. 8)
8
7. Further disassembly is not necessary or recommended for routine service.
REASSEMBLY
1. Replace cocking handle and plunger into top of slide assembly. (See Fig. 9) Plunger end goes into cocking handle.
9
1
10
16
3. Making sure the guide rod is engaged in the hole in the front of the receiver, hold the slide assembly in place (See Fig. 11A) while removing the pin/punch and allow slide to go forward slowly. (See Fig. 11B) 4. Place the receiver washer in its position around the take down screw hole inside the stock (refer to parts list, p. 27, for applicable serial number range). Then hook rear receiver hooks into stock recesses (See Fig. 12) and lower barrel back into place while holding cocking handle back slightly (approximately 1 inch). (See Fig. 13)
11A
11B
1 2
12
13
Note: If bolt is not held open slightly while lowering barreled action into stock, it will be impossible to operate action! If this occurs, simply lift the action slightly out of the stock, retract the bolt slightly, and keep it open as you lower the action back into the stock. Once the barrel/receiver assembly is in place in the stock, replace the take down screw and lock washer. While replacing the take down screw and lock washer, ensure that the receiver spacer is in place inside the stock if your carbine is so equipped. (See Fig. 14)
5. Replace barrel band and screw. Check to assure free movement of slide and correct functioning of trigger and manual safety. (See Fig.14)
1 3
14
17
DAMAGED, NON-STANDARD, OR IMPROPERLY ASSEMBLED MAGAZINES SHOULD NOT BE USED. THEY CAN CAUSE THE RIFLE TO MALFUNCTION.
18
conditions, disassemble, clean and oil it. Proper periodic maintenance is essential to the reliable functioning of any firearm. To clean the rifle, proceed as follows: 1. Disassemble (field-strip) the rifle to the extent described on pages 15 & 16. 2. Using a cleaning rod, run a solvent-wetted patch through the bore several times. Then attach a solvent-wetted bristle brush to the rod and run it back and forth the full length of the bore as many times as necessary to remove grease and dirt from the bore and chamber. Clean bore with dry patches and examine. Bore fouling can contribute to reduced accuracy, and grease accumulation in the chamber can interfere with proper feeding of cartridges from the magazine.
WARNING LUBRICATION
O IL
Firing a rifle with oil, grease, or any other material even partially obstructing the bore may result in damage to the rifle and serious injury to the shooter and those nearby. Do not spray or apply lubricants directly on ammunition. If the powder of a cartridge is affected by the lubricant, it may not be ignited, but the primer firing may push the bullet into the bore where it may be lodged. Firing a subsequent bullet into the obstructed bore may damage the rifle and cause serious injury or death to the shooter and those nearby. Use lubricants properly. You are responsible for the proper care and maintenance of your firearms.
STORAGE
GUNS SHOULD NOT BE STORED LOADED!
USE THE LOCKING DEVICE SUPPLIED WITH THE RIFLE FOR STORAGE. (SEE PAGE 2)
Do not store the rifle in a leather case or scabbard. Leather attracts moisture, even though it may appear to be dry.
19
WARNING STORAGE
Never place or store any firearm in such a manner that it may be dislodged. Firearms should always be stored securely and unloaded, away from children and careless adults. Use the locking device originally supplied with this firearm for storage. The use of a locking device or safety lock is only one aspect of responsible firearms storage. For increased safety, firearms should be stored unloaded and locked in a location that is both separate from their ammunition and inaccessible to children and any other unauthorized person.
SIGHT ADJUSTMENT
The RUGER CARBINE rifles are equipped with an adjustable rear sight. Each click of the sight adjustment screw (either windage or elevation) will move the point of impact of the bullet approximately 3/4 at a range of 25 yards. Be careful not to use one of the curved front sight blade protectors as a front sight when you aim -- the front sight is a vertical post. ELEVATION
WINDAGE
UP
DOWN
RIGHT
LEFT
To raise point of impact: turn screw counterclockwise. To lower point of impact: turn screw clockwise. To move the point of impact to the right: turn screw counterclockwise. To move the point of impact to the left: turn screw clockwise.
21
SUGGESTED SIGHT PICTURE Top of front sight even with top of rear sight blade. Front sight centered in notch of rear sight blade. Target bulls-eye centered on top of front sight.
Aperture G06202
22
WARNING: BEFORE SHIPPING ANY FIREARM, BE ABSOLUTELY CERTAIN THAT IT AND ITS MAGAZINE ARE UNLOADED. DO NOT SHIP CARTRIDGES WITH A FIREARM.
23
Work performed will bear a net minimum labor charge of $20.00 plus a $12.00 shipping and handling charge. The charge for metal refinishing the RUGER CARBINE rifle is $50.00 plus a $12.00 shipping and handling charge. Custom gunsmithing service or nonstandard alterations are NOT AVAILABLE from Ruger Product Service Departments.
ORDERING PARTS
Please contact the Arizona Product Service Department for parts availability and current prices. All parts orders for the RUGER CARBINE rifles should be sent to: Sturm, Ruger & Company, Inc., Parts Department, 200 Ruger Road, Prescott AZ 86301-6181, (520)778-6555. We cannot comply with open account or C.O.D. requests. Payment in the form of a check, money order, Visa or Mastercard must accompany your order. Credit Card orders must include the account number, expiration date and whether it is a Visa or Mastercard account. Minimum parts order is $1.00 plus a $3.50 shipping and handling charge. Order parts by Part Number and Part Name, include the entire serial number of the firearm for which the parts are being ordered. There is a minimum net labor charge of $20.00 plus $12.00 shipping and handling charge if the parts are factory fitted. All factory-fitted parts are fitted on an exchange basis only. We will not return the replaced parts. Because the CARBINE receiver (part number G00125 or G00101) is a serial numbered component, it is defined as a firearm by Federal law and is not sold as a separate component. *Parts designated by an asterisk must be factory fitted. These parts are fitted on an exchange basis only. We will not return the replaced parts. We will not return any part that is broken, malfunctioning, badly worn or has been modified. See Warning Parts Purchasers above.
CAUTION: A gun containing modified, broken, malfunctioning, or badly worn parts should not be fired.
24
RUGER CARBINE
PARTS LIST
Design, prices and specifications subject to change without notice. SPECIFY MODEL AND CALIBER WHEN ORDERING (See Exploded View on Pages 30). Part Name * Barrel * Barrel Barrel Band Barrel Band Barrel Band Assembly Barrel Band Screw * Bolt Lock Bolt Lock Cross Pin, 2 Reqd Bolt Lock Spring Butt Plate Screw, 2 Reqd Cable Lock, 10 - For Ruger Rifles Only Cocking Handle Cocking Handle Plunger Cocking Handle Plunger Spring Disconnector Disconnector Pivot Pin Ejector Extractor Part No. G00325 G00300 G06501 G06510 G06510-100 C-69H G07301 G07900 G09000 C-91SM PM120A G02505 G07100 G07200 G06701 G06800 G00802 G01425 Model PC9, PC9GR PC4, PC4GR PC9, PC4 PC9GR, PC4GR PC9GR, PC4GR All Models All Models All Models All Models All Models All Models All Models All Models All Models All Models All Models All Models PC9, PC9GR
25
Part Name Extractor Extractor Spring Extractor Pin Firing Pin Firing Pin Retaining Pin Firing Pin Spring * Front Sight Front Sight Cross Pin Ghost Ring Sight Adjustment Nut Ghost Ring Sight Aperture Ghost Ring Sight Assembly Ghost Ring Sight Base Ghost Ring Sight Base Screw, 2 Reqd Ghost Ring Sight Installation Kit Ghost Ring Sight Lock Screw Ghost Ring Sight Windage Adjustment Screw Guide Rod/Recoil Spring Assembly * Hammer Hammer Pivot Pin Hammer Spring Hammer Strut Handguard Assembly Handguard Plug, Not Illustrated Lever Actuator
Part No. G01401 G01500 G01601 KG01100 G06000 KV01850 G05603 MA07201 G06451 G06202 G06202-100 G06302 G06401 G06202-200 G06410 G06250 G15101 G01703 G01900 G04701 G01801 G10500 G00551 G07501
Model PC4, PC4GR All Models All Models All Models All Models All Models All Models All Models PC9GR, PC4GR PC9GR, PC4GR PC9GR, PC4GR PC9GR, PC4GR PC9GR, PC4GR PC9, PC4 PC9GR, PC4GR PC9GR, PC4GR All Models All Models All Models All Models All Models All Models PC9GR, PC4GR All Models
26
Part Name Magazine, Complete Magazine, Complete Magazine Latch Magazine Latch Magazine Latch Retaining Pin Magazine Latch Spring Magazine Latch Spring Pivot Pin Retainer Rear Sight, Adjustable, Complete Rear Sight, Adjustable, Complete Rear Sight Body, Complete Rear Sight Body, Complete Rear Sight Body Rear Sight Base Rear Sight Base Set Screw Rear Sight Blade Rear Sight Blade, with White Outline Notch Rear Sight Detent Ball Rear Sight Elevation Screw Rear Sight Elevation Spring Rear Sight Windage Adjustment Screw Rear Sight Windage Spring Receiver Spacer
Part No. P-18/10 P-17/10 G03125 G03101 G01200 G05000 G05050 G05501 A15901-202 A15901-203 A15901-102 A15901-103 A05900 A06100 A06200 G08701 H07203 MR05908 MR05902 MR05906 E05903 MR05907 G09900
Model PC9, PC9GR PC4, PC4GR PC9 PC9GR PC4, PC4GR All Models PC9, PC9GR PC4, PC4GR All Models PC9 PC4 PC9 PC4 PC9, PC4 PC9, PC4 PC9, PC4 PC9 PC4 PC9, PC4 PC9, PC4 PC9, PC4 PC9, PC4 PC9, PC4 PC9, PC4
27
For PC9 rifles with serial numbers below 470-01666 and For PC4 rifles with serial numbers 480-02000 to 480-03110
* * * *
* *
Part Name Recoil Block Recoil Block Recoil Pad Reversing Lever Safety Safety Plunger Safety Plunger Spring Sear Sear Interrupter Sear Interrupter Plunger Sear Interrupter Plunger Spring Sear Spring Sear Spring Plunger Slide Slide Slide Stop Assembly Slide Stop Slide Stop Plunger Slide Stop Spring Sling Swivel, Front Sling Swivel Adapter, Front Sling Swivel Rear Mounting Screw Stock Stock Bolt
Part No. G00703 G00704 J05602 G07403 G03803 KG04800 G04900 G02305 G01300 G05200 G05301 G02401 G05900 G13725 G13701 G13202 G03205 KV06700 G04605 S-85 B08600 S-87 G00400 G05700
Model PC9, PC4 PC9GR, PC4GR All Models All Models All Models All Models All Models All Models All Models All Models All Models All Models All Models PC9, PC9GR PC4, PC4GR PC9, PC9GR PC4, PC4GR PC4, PC4GR PC4, PC4GR PC9GR, PC4GR PC9GR, PC4GR PC9GR, PC4GR All Models All Models
28
Part Name Stock Bolt Bushing Stock Bolt Lock Washer Take Down Screw Take Down Screw Flat Washer Take Down Screw Lock Washer Trigger Trigger Pivot Pin Trigger Spring Trigger Spring Support * PARTS SO MARKED MUST BE FACTORY FITTED 29
Part No. G08100 G06100 G09200 G09401 G09300 KG02005 G02100 G02201 G03000
Model All Models All Models All Models All Models All Models All Models All Models All Models All Models
* The receiver spacer (Part No. G09900) is for PC9 rifles with serial numbers below 470-01666 and for PC4 rifles with serial numbers 480-02000 to 480-03110.
30
1. LEARN THE MECHANICAL AND HANDLING CHARACTERISTICS OF THE FIREARM YOU ARE USING.
Not all firearms are the same. The method of carrying and handling firearms varies in accordance with the mechanical provisions for avoiding accidental discharge and the various proper procedures for loading and unloading. No person should handle any firearm without first having thoroughly familiarized himself with the particular type of firearm he is using, and with safe gun handling in general.
MANU CTION INSTRU CTIONS E INSTRU READ TH NINGS IN THIS RE AND WARCAREFULLY BEFO MANUAL IS FIREARM. USING TH
RUGER AL
A safe direction must take into account the fact that a bullet may penetrate a wall, ceiling, floor, window, etc., and strike a person or damage property. Make it a habit to know exactly where the muzzle of your gun is pointing whenever you handle it, and be sure that you are always in control of the direction in which the muzzle is pointing, even if you fall or stumble. Keep your finger off the trigger until you are ready to shoot.
32
33
34
A current catalog of Ruger firearms is available free upon request to Sturm, Ruger & Co., Inc., Southport, CT 06490. 35
WHY NO WARRANTY CARD HAS BEEN PACKED WITH THIS NEW RUGER FIREARM
The Magnuson-Moss Act (Public Law 93-637) does not require any seller or manufacturer of a consumer product to give a written warranty. It does provide that if a written warranty is given, it must be designated as limited or as full and sets minimum standards for a full warranty. Sturm, Ruger & Company, Inc. has elected not to provide any written warranty, either limited or full, rather than to attempt to comply with the provisions of the Magnuson-Moss Act and the regulations issued thereunder. There are certain implied warranties under state law with respect to sales of consumer goods. As the extent and interpretation of these implied warranties varies from state to state, you should refer to your state statutes. Sturm, Ruger & Company wishes to assure its customers of its continued interest in providing service to owners of Ruger firearms.
RUGER, the Sturm, Ruger logo, SINGLE-SIX, BLACKHAWK, REDHAWK, SECURITY-SIX, SPEED-SIX, SERVICE-SIX, BEARCAT, OLD ARMY, 10/22, MINI-14, MINI THIRTY, RANCH RIFLE, M77, 77/22, GP-100, SP101, P-85 and VAQUERO are registered U.S. trademarks.