Professional Documents
Culture Documents
Panasonic Lumix Dmc-ls1 Series SM Repair Guide (ET)
Panasonic Lumix Dmc-ls1 Series SM Repair Guide (ET)
DSC0503007C0 B26
Digital Camera
DMC-LS1PP DMC-LS1PL DMC-LS1EB DMC-LS1EG DMC-LS1EGM DMC-LS1GC DMC-LS1GK DMC-LS1GN DMC-LS1GT DMC-LS1SG
Vol. 1
Colour (S)...........Silver Type (A)...........Blue Type (GC and GK only) (T)...........Brown Type (GC only)
2005 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
CONTENTS
Page
1 INTRODUCTION 1.1. INTRODUCTION 1.2. ABOUT LEAD FREE SOLDER (PbF) 1.3. IMPORTANT NOTICE 1: (Other than U.S.A. and Canadian Market) 1.4. HOW TO DEFINE THE MODEL SUFFIX (NTSC or PAL model) 2 SAFETY PRECAUTIONS 2.1. GENERAL GUIDELINES 2.2. LEAKAGE CURRENT COLD CHECK 2.3. LEAKAGE CURRENT HOT CHECK (See Figure 1.) 3 PREVENTION OF ELECTRO STATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES 4 HOW TO REPLACE THE LITHIUM BATTERY 4.1. REPLACEMENT PROCEDURE 5 OPERATING GUIDE 6 SERVICE NOTES 6.1. WHEN REPLACING THE MAIN C.B.A. 6.2. SERVICE POSITION 6.3. HOW TO DISCHARGE THE CAPACITOR ON FLASH TOP C.B.A. 6.4. CLEANING LENS AND LCD PANEL 7 ADJUSTMENT PROCEDURES 7.1. SERVICE FIXTURE AND TOOLS 8 ERROR CODE MEMORY FUNCTION 13 13 14 15 16 7 8 8 10 12 12 12 4 6 6 6 6 3 3 3 3 9 CONFIRMATION OF FIRMWARE VERSION 10 DISASSEMBLY PROCEDURE 10.1. DISASSEMBLY FLOW CHART 10.2. C.B.A. LOCATION 10.3. DIASSEMBLY PROCEDURE 10.4. DISASSEMBLY PROCEDURE FOR THE LENS 10.5. ASSEMBLY PROCEDURE FOR THE LENS 10.6. REMOVAL OF THE CCD 10.7. THE APPLYMENT OF GREASE METHOD 11 SCHEMATIC DIAGRAMS 11.1. OVERALL BLOCK DIAGRAM 11.2. WIRING CONNECTION DIAGRAM 11.3. FLASH TOP SCHEMATIC DIAGRAM 11.4. CCD SCHEMATIC DIAGRAM 11.5. LENS FLEX SCHEMATIC DIAGRAM 12 CIRCUIT BOARD ASSEMBLIES 12.1. CCD C.B.A. 12.2. FLASH TOP C.B.A. 12.3. LENS FLEX C.B.A. 13 EXPLODED VIEWS 13.1. FRAME & CASING SECTION 13.2. PACKING PARTS & ACCESSORIES SECTION 14 REPLACEMENT PARTS LIST 14.1. MECHANICAL REPLACEMENT PARTS LIST 14.2. ELECTRICAL REPLACEMENT PARTS LIST
Page
19 20 20 20 21 25 27 30 30 31 31 32 33 33 34 35 35 36 37 38 38 40 41 41 43
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
1 INTRODUCTION
1.1. INTRODUCTION
This service manual contains technical information, which allow service personnels to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
1.2.
Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a PbF stamp on the PCB. Caution: Pb free solder has a higher melting point than standard solder, Typically the melting point is 50-70F (30-40C) higher. Please use a high temperature soldering iron. In case of soldering iron with temperature control, please set it to 70020F (37010C) Pb free solder will tend to splash when heated too high (about 1100F/600C). When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat the soldering points with the Pb free solder until it melts enough.
1.3.
1. The service manual does not contain the following information, because of the impossibility of servicing at component level. a. Schematic diagram, Block Diagram and C.B.A. layout of Main C.B.A. b. Parts list for individual parts of Main C.B.A. When a part replacement is required for repairing Main C.B.A., replace as an assembled parts. (Main C.B.A.) 2. The following category is/are recycle module part. please send it/them to Central Repair Center. MAIN C.B.A. (VEP56021A) : Excluding replacement of Lithium Battery
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
1.4.
There are six kinds of DMC-LS1, regardless of the colours. DMC-LS1S DMC-LS1PP DMC-LS1EB/EG/EGM/GN DMC-LS1GC/SG DMC-LS1GT DMC-LS1PL/GK (DMC-LS1S is exclusively Japan domestic model.) What is the difference is that the INITIAL SETTING data which is stored in Flash ROM mounted on Main C.B.A.
1.4.1.
Defining methods:
To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.
NOTE: After replacing the MAIN C.B.A., be sure to achieve adjustment. The adjustment instruction is available at software download on the CS-Web from AVC web-site in TSN system.
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
1.4.2.
INITIAL SETTINGS:
When you replace the Main C.B.A., be sure to perform the initial settings after achieving the Adjustment, by ordering the following procedure in accordance with model suffix. Step 1. The temporary cancellation of factory setting: Set the mode dial to Normal Picture (Red camera mark). and UP of Cross key simultaneously, turn the Power on. While keep pressing Optical Image Stabilizer Step 2. The cancellation of factory setting: Set the mode dial to Playback Step 3. Turn the Power on: Set the mode dial to Normal Picture Step 4. Display the INITIAL SETTING: While keep pressing MENU and RIGHT of Cross key simultaneously, turn the Power off. (Red camera mark), and then turn the Power on. . and UP of Cross key simultaneously, turn the Power off. While keep pressing Optical Image Stabilizer
Step 5. Set the INITIAL SETTING: Select the area with pressing UP / DOWN of Cross key, and then press the RIGHT of Cross key.
The only set area is displayed, and then press the " RIGHT automatically.)
Confirm the display of PLEASE SET THE CLOCK in English when the unit is turned on again. (For China and Taiwan market, the display shows PLEASE SET THE CLOCK in Chinese.) NOTE: The display shows SET THE CLOCK when turn the Power on again. Connect the unit to PC with USB cable and is detected as removable media. 1) As for your reference Default setting condition is given in the following table. Default setting (After INITIAL SETTINGS)
a) b) c) d) e) MODEL DMC-LS1S DMC-LS1PP/PL DMC-LS1EB/EG/EGM/GC/GN/SG DMC-LS1GK DMC-LS1GT VIDEO OUTPUT NTSC NTSC PAL PAL NTSC LANGUAGE Japanese English English Chinese (simplified) Chinese (traditional) DATE Year/Month/Date Month/Date/Year Date/Month/Year Year/Month/Date Year/Month/Date REMARKS
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
2 SAFETY PRECAUTIONS
2.1. GENERAL GUIDELINES
1. IMPORTANT SAFETY NOTICE There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturers specified parts to prevent X-RADIATION, shock, fire, or other hazards. Do not modify the original design without permission of manufacturer. 2. An Isolation Transformer should always be used during the servicing of AC Adaptor whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect AC Adaptor from being damaged by accidental shorting that may occur during servicing. 3. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 4. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed. 5. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
2.3.
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 1.5 k, 10 W resistor, in parallel with a 0.15 F capacitor, between each exposed metallic part on the set and a good earth ground, as shown in Figure 1. 3. Use an AC voltmeter, with 1 k/V or more sensitivity, to measure the potential across the resistor. 4. Check each exposed metallic part, and measure the voltage at each point. 5. Reverse the AC plug in the AC outlet and repeat each of the above measurements. 6. The potential at any point should not exceed 0.75 V RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 mA. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.
2.2.
1. Unplug the AC cord and connect a jumper between the two prongs on the plug. 2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1 M and 5.2 M. When the exposed metal does not have a return path to the chassis, the reading must be infinity.
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
NOTE: This Lithium battery is a critical component. (Type No.: ML-614S/ZT Manufactured by Matsushita Battery Industrial Co.,Ltd.) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in requirement designed specifically for its use. Replacement batteries must be of same type and manufacture. They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed. Do not attempt to re-charge the old battery or re-use it for any other purpose. It should be disposed of in waste products destined for burial rather than incineration.
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
NOTE: Above caution are also applicable for below batteries which is for DMC-LS1 all series, as well. 1. AA Oxyride batteries 2. AA Alkaline batteries 3. AA Rechargeable Ni-MH (nickel-metal hydride) batteries
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
5 OPERATING GUIDE
10
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
11
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
6 SERVICE NOTES
6.1. WHEN REPLACING THE MAIN C.B.A.
After replacing the MAIN C.B.A., be sure to achieve adjustment. The adjustment instruction is available at software download on the CS-Web from AVC web-site in TSN system, together with Maintenance software.
6.2.
No. 1 2 3 4 5
SERVICE POSITION
Parts No. VFK1582A2125 VFK1951 VFK1870 VFK1950 VFK1576DC202 Table S1 Extension Cable List Connection FP9002 (MAIN) - CCD UNIT FP9001 (MAIN) - LENS UNIT PP9001 (MAIN) - PS8001 (FLASH TOP) FP9003 (MAIN) - LCD UNIT P9001 (MAIN) - LCD BACKLIGHT Form 21PIN 0.5 FFC 39PIN 0.3 FFC 30PIN B to B 33PIN 0.3 FFC 2PIN CABLE
This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
NOTE: When the Main C.B.A. is energized, be sure to connect the LCD backlight connector (P9001) to the Main C.B.A.. If the Main C.B.A. is energized that the LCD backlight connector (P9001) is opened, it may be caused to the case not only the power does not turn on but also transisitor (Q1070) is broken.
CAUTION 1. Be sure to discharge the capacitor for flash, which is connected with FLASH TOP C.B.A. (Refer to HOW TO DISCHARGE THE CHARGING CAPACITOR ON FLASH TOP C.B.A..)
12
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
6.3.
CAUTION: 1. Be sure to discharge the capacitor on FLASH TOP C.B.A.. 2. Be careful of the high voltage circuit on FLASH TOP C.B.A. when servicing. [Discharging Procedure] 1. Refer to the disassemble procedure and Remove the necessary parts/unit. 2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k /5W). (an equivalent type of resistor may be used.) 3. Put the resistor between both terminals of capacitor on FLASH TOP C.B.A. for approx. 5 seconds. 4. After discharging, confirm that the capacitor voltage is lower than 10V using a voltmeter.
6.4.
Do not touch the surface of lens and LCD Panel with your hand. When cleaning the lens, use air-Blower to blow off the dust. When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface. Note: A lens cleaning paper and lens cleaner are available at local camera shops and market place.
13
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
7 ADJUSTMENT PROCEDURES
Even if the MAIN C.B.A. is replaced as a unit, it must be achieved the adjustment and factory setting. The adjustment in this unit is separated two types as shown below. The adjustment instruction is available at "Software download" on the CS-Web from AVC" web-site in "TSN System". 1. Main unit adjustment: All adjustments except for LCD adjustment. This unit mounts the adjustment software for main unit, it wouldnt need the connection between the PC and this unit with USB cable. 2. LCD adjustment: Adjustment for LCD. It need the connection between the PC and this unit with USB cable. The adjustment instruction is available at "Software download" on the CS-Web from AVC" web-site in "TSN System", together with maintenance software.
14
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
7.1.
The following Service Fixture and tools are used for checking and servicing this unit.
15
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
3. The change of display: The error code can be memorized 32 error codes in sequence, however it is displayed 5 errors on the LCD. Display can be changed by the following procedure: " UP or DOWN or RIGHT of Cross key": It can be scroll up or down one. of Cross key": It can be display last 5 error or another 5 error. " LEFT
4. How to read the error code: One error code is displayed for 8 bit, the contents of error codes is indicated the table as shown below.
16
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
Attribute LENS
C.B./Zoom
Zoom
Focus
Lens
Adj.History
OIS
Error code Contents (Upper) High 4 bits Low 4 bits Check point (Lower) 1800 1000 PSD (X) error. Hall element (X axis) position detect error in OIS unit. OIS Unit 2000 PSD (Y) error. Hall element (Y axis) position detect error in OIS unit. OIS Unit 3000 GYRO (X) error. Gyro (IC7102: X axis) detect error on Main C.B.A.. IC7102 (Gyro element) or IC6001 (VENUS PLUS) 4000 GYRO (Y) error. Gyro (IC7101: Y axis) detect error on Main C.B.A.. IC7101 (Gyro element) or IC6001 (VENUS PLUS) 5000 MREF error (Reference voltage error). IC7002 (LENS drive) or IC6001 (VENUS PLUS) 6000 Drive voltage (X) error. VENUS PLUS AD value error, LENS Unit, LENS flex breaks etc. 7000 Drive voltage (Y) error. VENUS PLUS AD value error, LENS Unit, LENS flex breaks etc. 0100 HP Low detect error (C.B. encoder (full retract) always Low detect). FP9001-(23) signal line or IC6001 (VENUS PLUS) 0200 HP High detect error (C.B. encoder (full retract) always High detect). FP9001-(23) signal line or IC6001 (VENUS PLUS) 0300 ENC1 detect error (C.B. motor encoder detect error). FP9001-(3) signal line or IC6001 (VENUS PLUS) 0400 ENC2 detect error (C.B. motor encoder detect error). FP9001-(5) signal line or IC6001 (VENUS PLUS) 0010 HP Low detect error (Zoom encoder always Low detect error). FP9001-(3, 5) signal line or IC6001 (VENUS PLUS) 0020 HP High detect error (Zoom encoder always High detect error). FP9001-(3, 5) signal line or IC6001 (VENUS PLUS) 0030 ENC1 detect error (Zoom encoder detect error). FP9001-(3) signal line or IC6001 (VENUS PLUS) 0040 ENC2 detect error (Zoom encoder detect error). FP9001-(5) signal line or IC6001 (VENUS PLUS) 0001 HP Low detect error (Focus encoder always Low detect error). FP9001-(23) signal line or IC6001 (VENUS PLUS) 0002 HP High detect error (Focus encoder always High detect error). FP9001-(23) signal line or IC6001 (VENUS PLUS) 1801 0000 Power ON time out error. Lens drive system 1802 0000 Power OFF time out error. Lens drive system 1900 2000 OIS adj. Yaw direction amplitude error (small) 3000 OIS adj. Pit direction amplitude error (small) 4000 OIS adj. Yaw direction amplitude error (large) 5000 OIS adj. Pit direction amplitude error (large) 6000 OIS adj. MREF error 7000 OIS adj. time out error 8000 OIS adj. Yaw direction off set error 9000 OIS adj. Pit direction off set error A000 OIS adj. Yaw direction gain error B000 OIS adj. Pit direction gain error C000 OIS adj. Yaw direction position sensor error D000 OIS adj. Pit direction position sensor error E000 OIS adj. other error
17
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
Attribute HARD
SOFT
CPU
Card
Memory
Error code Contents (Upper) High 4 bits Low 4 bits Check point (Lower) Flash 2000 0000 Flash charging error. IC6001-(13) signal line or Flash charging circuit FLASH ROM 2B00 0001 EEPROM read error (EEPROM IC6002 (FLASH ROM) Area) 0002 EEPROM write error IC6002 (FLASH ROM) RTC 2C00 0001 SYSTEM IC initialize failure error Communication between IC6001 (VENUS PLUS) and IC9101 (SYSTEM) Reset 3000 0001 NMI reset | Non Mask-able Interrupt 0007 (30000001-30000007 are caused by factors) Card 3100 0001 Card logic error SD card data line or IC6001 (VENUS PLUS) 0002 Card physical error SD card data line or IC6001 (VENUS PLUS) 0003 Read error SD card data line or IC6001 (VENUS PLUS) 0004 Write error SD card data line or IC6001 (VENUS PLUS) 0005 Format error SD card data line or IC6001 (VENUS PLUS) Stop 3800 0001 Camera task finish process time out. Communication between Lens system and IC6001 (VENUS PLUS) 0002 Camera task invalid code error. IC6001 (VENUS PLUS) 0100 File time out error in recording motion image IC6001 (VENUS PLUS) 0002 File data send error in recording motion image IC6001 (VENUS PLUS) Monitor 1000 AF frame movement check time out. IC6001 (VENUS PLUS) Built-in 3900 0005 Built-in memory format error memory FLASH ROM data line or IC6001 (VENUS PLUS)
Sub item
5. How to returned to Normal Display: Turn the power off and on, to exit from Error code display mode. NOTE: The error code can not be initialized by the unit only.
18
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
(The version information is displayed on the LCD with green colour letters.) (Fig. B)
Point: The firmware version and EEPROM version can be confirmed with the information (1). The information (2), (3) are just reference.
19
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
10 DISASSEMBLY PROCEDURE
10.1. DISASSEMBLY FLOW CHART
20
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
10.3.1.
LCD Unit
Fig. D2 Fig. D3
3 4
Fig. D4 Fig. D5
Fig. D6
Main C.B.A.
Fig. D7 Fig. D8
Lens Unit
Fig. D11
Fig. D1
21
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
10.3.2.
Fig. D2
Fig. D3
10.3.3.
Fig. D4
22
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
10.3.4.
10.3.5.
Fig. D5
Fig. D6
23
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
Fig. D7
10.3.6.
10.3.7.
Fig. D8
Fig. D10
24
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
10.3.8.
10.4.1.
1. Remove the solders (2 points). 2. Remove the lock (5 points). 3. Unscrew the 5 screws (A). 4. Remove the Zoom Motor Unit to the indicated by arrow. 5. Remove the Cover to the indicated by arrow. 6. Remove the Master Flange Unit.
Fig. D11
NOTE: (When Assembling) Confirm the contents as shown below. Condition of the screw is tightened. Assembling condition of mechanism parts (distortion, space etc.). Dust and dirt of the lens, display condition of the LCD (gradient etc.). Dust and dirt of the LCD
25
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
10.4.2.
Removal of the Drive/Direct Unit, 1st Lens Frame/2nd Lens Frame Move Unit
1. Push the 1st lens frame move unit to the indicated by arrow from lens side, and then remove the unit of 1st lens frame/2nd lens frame move unit from the drive/direct unit.
10.4.3.
1. Push the drive unit to the indicated by arrow from lens side, and then remove the unit of drive/direct unit, 1st lens frame/2nd lens frame move unit from the fixed frame unit.
26
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
10.4.4.
27
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
10.5.2.
28
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
10.5.3.
Assembly for the Zoom Motor Unit and Master Flange Unit
29
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
30
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
11 SCHEMATIC DIAGRAMS
11.1. OVERALL BLOCK DIAGRAM
OVERALL BLOCK DIAGRAM
IC3101 CCD
4 MEGA PIX
IC6003 SDRAM/128M-bit
OIS UNIT
ZOOM
IRIS (ND)
SHUTTER
FOCUS
SD CARD
IC3002 V-DRIVE
IC7002 MOTOR DRIVE, OIS DRIVE& PRE PROCESS IC2001 VIDEO AMP
FLASH
IC9101 SYSTEM IC
X9101
DC IN/EXT. TERMINAL
IC1001 POWER
(POWER SUPPLY) BATTERY
31
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
UNREG UNREG UNREG UNREG UNREG GND UNREG GND UNREG GND UNREG GND TELE WIDE D GND OIS SW SHUTTER 0 SHUTTER 1 POWER ON
ST TRG 5V STB PWM OUT STB CHG LV STB SAFE NC A GND BUZZER BUZZER R KEY IN3 KEY IN2 FRAME GND FRAME GND FRAME GND FRAME GND
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
32
2 1 BL L BL H
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 Z1 LEDCNT Z2 LEDCNT Z2 ENC VCC ZM1 ZM2 ZM2 IRIS1 SHUT2 SHUT1 IRIS2 FENC VCC Y VO+ X VO+ X VOY DRV+ X DRV+ Y VOFBP FAN
Z1 ENC VCC Z1ABS Z2ABS ZM1 ZM1 ZM2 IRIS1 SHUT2 SHUT1 IRIS2 F LEDCNT FABS Y VH+ X VH+ X VHY DRVX DRVY VHFBN FAP
33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1
VCOM TEST BLON DI VSYNC CLK D04 D02 D00 NC VSH VDD VDC1 C2C1COMOUT VSS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
VH V1 [OV1] V2 [OV2] V3/V3A [OV3] V6/V3B [OV5] V4 [OV4] V5A [OV7] V5B [OV8] V6 [OV6] VL BSUB SUB HL CCD GND H1 H2 CCD GND R GUARD1 CCDOUT GUARD1
PP9001
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
UNREG UNREG UNREG UNREG UNREG GND UNREG GND UNREG GND UNREG GND TELE WIDE D GND OIS SW SHUTTER 0 SHUTTER 1 POWER ON
ST TRG 30 5R0V 29 28 STB PWM OUT 27 STB CHG LV STB SAFE 26 NC 25 A GND 24 BUZZER 23 BUZZER R 22 KEY IN3 21 KEY IN2 20 19 FRAME GND 18 FRAME GND 17 FRAME GND 16 FRAME GND
P9001
: (COMPONENT SIDE)
LCD UNIT
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
E
21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 VH V1 [OV1] V2 [OV2] V3A [OV3] V3B [OV5] V4 [OV4] V5A [OV7] V5B [OV8] V6 [OV6] VL BSUB SUB HL CCD GND H1 H2 CCD GND R CCD GND CCDOUT CCD GND
TL8002 LAMP[-]
C3101 1
T8001 C8002 G5DYA0000100 D8003 B0HCGR000004 0.033 4 2 D8004 B0HCGR000004 C8008 10 3 1 C8005 10
CL8001 PS8001 K1KB30AA0116 1 UNREG 2 UNREG 3 UNREG 4 UNREG 5 UNREG GND 6 UNREG GND 7 UNREG GND 8 UNREG GND 9 TELE 10 WIDE 11 D GND 12 OIS SW 13 SHUTTER 0 14 SHUTTER 1 15 POWER ON 16 FRAME GND 17 FRAME GND 18 FRAME GND 19 FRAME GND 20 KEY IN2 21 KEY IN3 22 BUZZER R 23 BUZZER 24 A GND 25 NC 26 STB SAFE 27 STB CHG LV 28 STB PWM OUT 29 5V 30 ST TRG
C3103 2.2
C8003 300V100
C8004 1000P
C8010 10 CL8005
3 2
CL8003
L8001 G5FYA0000004
Q8009 B1DFCG000010
R8032 1M (FLASH DRIVE) 0 3 2.8 2.8 2 1
VSUB
Q8001 B1JBLP000008
(LAMP DRIVE) 5 6 7 0 8
IC3101
V5A V5B
V3B
BSUB
V3A
VPT
V4
V2
V1
Q8002 B1DFGC000003
(FLASH DRIVE) 1 2 3 0 R8003 0 0 4 OUT Y GND 3 IN A 0 2 5.0 5 VCC IN B 1 CL8008 CL8004 CL8010 4
V0
VDD
PW
H1
HL
RG
R3108 1M
C3104 0.01
18
H2
17
16
15
14
13
12
11
10
R3105 0
Q3101 2SC4627J0L
(CCD AMP) R3101 33
IC8001 C0ZBZ0001011 C
(ST TRG AMP) 5.0
R3102 2200
CL8006
CL8002
C8001 1
MODE SW S8005 K0G188A00002 R8001 2400 SHUTTER SW S8001 K0F212A00001 5 7 CL8007 C 9 8 1 2 3 R8009 8200 1 2 1 3 6 4 CL8012 3
R8010 8200
R8008 4300
A
R8011 4300 R8012 2400 CL8016 CL8015
NOTE: (When Replacing) The following component are not mounted on the Flash Top C.B.A. which is supplied as a replacement. Be sure to put the following component when replacing the Flash Top C.B.A. as a unit. Ref No. L8001 (Transformer), Ref No. C8003 (E. capacitor)
33
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
A1 A2 A3 B1 B2 B3 C1
PHOTO SENSOR
Z2 LED CNT Z2 ABS Z2 ENC VCC ZM1(+) ZM1(+) ZM1(+) ZM2(-) ZM2(-)
DC MOTOR
C2 D1
E1
DC SOLENOID (IRIS)
D SHUTTER UNIT
E2 D2
DC SOLENOID (SHUTTER)
E SHUTTER UNIT
PHOTO SENSOR
(FULL RETRACT)
34
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
(COMPONENT SIDE)
ADDRESS INFORMATION CCD C.B.A. Integrated Circuit IC3101 B-2
Capacitor C-2 C3101 C-2 C3103 A-2 C3104 Resistor R3101 R3102 R3103 R3104 R3105 R3106 R3107 R3108 B-1 B-1 B-3 B-3 B-1 B-3 B-3 A-2
35
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
Transistor
F F C
Test Point
CL8001 CL8002 CL8003 CL8004 CL8005 CL8006 CL8007 CL8008 CL8009 CL8010 CL8011 CL8012 CL8013 CL8014 CL8015 CL8016 CL8017 CL8018 CL8019 CL8020 CL8021 TL8001 TL8002 TL8003 TP8001 TP8002 E-4 E-2 D-3 D-3 E-5 E-2 F-1 D-3 F-4 E-4 D-2 F-4 E-4 E-4 E-4 E-4 E-4 F-3 E-4 D-2 B-4 B-3 C-3 C-4 E-5 E-5 C F C C C F F C C C F C C C C C C C C F C C C C C C
Connector
PS8001 E-3 C
Diode
D8002 D8003 D8004 C-4 C-5 D-5 C C C
Transformer
T8001 D-4 C
Coil
L8001 C-3 C
Switch
S8001 S8002 S8003 S8004 S8005 F-2 G-2 E-1 G-1 E-2 F F F F F
Capacitor
C8001 C8002 C8003 C8004 C8005 C8006 C8007 C8008 C8009 C8010 D-2 D-4 A-4 C-4 E-4 C-3 D-1 E-4 E-4 E-4 F C C C C C F C C C
Resistor
R8001 R8002 R8003 R8004 R8006 R8008 R8009 R8010 R8011 R8012 R8013 R8021 R8032 R8033 D-2 D-1 D-1 D-3 C-4 D-2 D-2 E-2 E-2 E-2 D-1 D-3 D-5 D-1 F F F C C F F F F F F C C F
(FOIL SIDE)
1 2 3
(COMPONENT SIDE)
4 5
36
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
E
G OIS UNIT G6 G5 G4 G3 G2 G1 G7 G8 G9 G10 G11 G12
F C.B. ENCODER
(FULL RETRACT)
D, E
F2
SUTTER UNIT
D1 D2 F1 E2 E1 F3
UNIT
C2
UNIT
A2 A3 B2 B1
C1 B3 B ZOOM ENCODER 2
37
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
13 EXPLODED VIEWS
13.1. FRAME & CASING SECTION
38
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
39
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
40
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
14.1.1.
Ref. No. 1 1 1 2 3 3 3 4 5 6 7 7 7 8 9 9 9 10 11 12 13 13 13 14 15 16 17 18 19 20 22 24 25 51 52 53 54 55 56 57 58
VKF4001 VKF4005 VKF4006 VKW3277 VYK1P09 VYK1P10 VYK1P11 VMA0T29 VMD5285 VMP8287 VYK1N47 VYK1N69 VYK1N70 VGU9797 VKF3999 VKF4003 VKF4004 VKW3276 VMA0T21 VMS7584 VYK1N49 VYK1N67 VYK1N68 VYK1P08 VGQ8421 VGU9800 VGU9801 EFN-KRT42 K1PB02000058 L0DCDD000006 L5EDDXG00001 VEP56021A VEP58012A VDL1603 VEK0H65 VMB3683 VMB3683 VMX3437 L6DA8BEC0001 B3NAA0000092 B3NAA0000092
DMC-LS1 Silver series DMC-LS1 Blue series DMC-LS1 Brown series DMC-LS1 Silver series DMC-LS1 Blue series DMC-LS1 Brown series
14.1.2.
Ref. No. 101 102
VPF1221 VPK2972
102 102 102 102 102 103 107 (RTL) (RTL) 107 107 107 107 107
VPK3002 VPK3005 VPK2989 VPK3003 VPK2971 VPN6317 VQT0Q71 VQT0Q63 VQT0Q64 VQT0Q65 VQT0Q66 VQT0Q67
PAKING CASE PAKING CASE PAKING CASE PAKING CASE PAKING CASE PAD INSTRUCTION (ENGLISH) INSTRUCTION (GERMAN) INSTRUCTION (FRENCH) INSTRUCTION (ITALIAN) INSTRUCTION (DUTCH) INSTRUCTION (SPANISH)
DMC-LS1EB-S/ EG-S/EGM-S/ GC-S/GN-S/ GT-S/PL-S/ SG-S DMC-LS1GC-A DMC-LS1GC-T DMC-LS1GK-S DMC-LS1GK-A DMC-LS1PP-S BOOK DMC-LS1EB-S BOOK DMC-LS1EG-S BOOK DMC-LS1EG-S BOOK DMC-LS1EG-S BOOK DMC-LS1EG-S BOOK DMC-LS1EGM-S
41
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
Part Name & Description INSTRUCTION BOOK (PORTUGUESE) INSTRUCTION BOOK (DANISH) INSTRUCTION BOOK (SWEDISH) INSTRUCTION BOOK (ENGLISH)
Remarks
DMC-LS1EGM-S DMC-LS1EGM-S DMC-LS1EGM-S DMC-LS1GC-A/ GC-S/GC-T/ SG-S DMC-LS1GC-A/ GC-S/GC-T/ SG-S DMC-LS1GC-A/ GC-S/GC-T/ SG-S DMC-LS1GC-A/ GC-S/GC-T/ SG-S DMC-LS1GK-A/ GK-S DMC-LS1GN-S DMC-LS1GT-S DMC-LS1PL-S DMC-LS1PL-S DMC-LS1PL-S DMC-LS1PP-S DMC-LS1PP-S DMC-LS1EB-S/ GK-A/GK-S/ GN-S/PP-S DMC-LS1EG-S/ EGM-S/GC-A/ GC-S/GC-T/ PL-S
14.1.3.
Ref. No.
VFK1870
107
VQT0Q73
107
VQT0Q74
VFK1576DC202 EXTENSION CABLE (2PIN-CABLE) VFK1582A2125 EXTENSION CABLE (21PIN-FFC) VFK1950 EXTENSION CABLE (33PIN-FFC) EXTENSION CABLE (39PIN-FFC)
107
VQT0Q75
107
VQT0Q77
INSTRUCTION BOOK (CHINESE (SIMPLIFIED)) INSTRUCTION BOOK (ENGLISH) INSTRUCTION BOOK (CHINESE (TRADITIONAL)) INSTRUCTION BOOK (ENGLISH) INSTRUCTION BOOK (SPANISH) INSTRUCTION BOOK (POTUGUESE) INSTRUCTION BOOK (ENGLISH/SPANISH) INSTRUCTION BOOK (CANADIAN FRENCH) POLY BAG
VFK1951
ERG5SJ102 RESISTOR FOR DISCHARGING VFK1164TCM02 INFINITY LENS (WITH FOCUS CHART) VFK1164TDVLB LIGHT BOX VFK1949 TR CHART VFK1900BK LENS CLEANING KIT (BK) VFK1755 T3 TROX DRIVER VFK1829 GREASE(FOR LENS) VFK1850 GREASE(FOR FOCUS MOTOR)
108
VPF1132
POLY BAG
111
K1HA08CD0004 USB CABLE W/PLUG K1HA08CD0006 VIDEO CABLE W/PLUG VQT0Q88 INSTRUCTION BOOK(APPL.) (ENGLISH) VQT0Q84 INSTRUCTION BOOK(APPL.) (GERMAN/FRENCH) VQT0Q85 INSTRUCTION BOOK(APPL.) (ITALIAN/DUTCH) VQT0Q86 INSTRUCTION BOOK(APPL.) (SPANISH/PORTUGUESE) VQT0Q87 INSTRUCTION BOOK(APPL.) (SWEDISH/DANISH) VQT0Q89 INSTRUCTION BOOK(APPL.) (ENGLISH/ CHINESE(TRADITIONAL)) VQT0Q90 INSTRUCTION BOOK(APPL.) (ARABIC/RUSSIAN) VQT0Q91 VQT0Q92 VQT0P63 VQT0Q83 INSTRUCTION BOOK(APPL.) (CHINESE (SIMPLIFIED)) INSTRUCTION BOOK(APPL.) (ENGLISH) INSTRUCTION BOOK (APPL.) (CHINESE (TRADITIONAL)) INSTRUCTION BOOK(APPL.) (ENGLISH/SPANISH/ PORTUGUESE) INSTRUCTION BOOK(APPL.) (ENGLISH/CANADIAN FRENCH) CD-ROM
DMC-LS1EB-S DMC-LS1EG-S DMC-LS1EG-S DMC-LS1EGM-S DMC-LS1EGM-S DMC-LS1GC-A/ GC-S/GC-T/ SG-S DMC-LS1GC-A/ GC-S/GC-T/ SG-S DMC-LS1GK-A/ GK-S DMC-LS1GN-S DMC-LS1GT-S DMC-LS1PL-S
111 112
VQT0Q82 VFF0279-S
DMC-LS1PP-S (See Notes) DMC-LS1EB-S/ EG-S/EGM-S/ GC-A/GC-S/ GC-T/GK-A/ GK-S/GN-S/ GT-S/PL-S/ SG-S
42
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
E.S.D. standards for Electrostatically Sensitive Devices, refer to PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES section. Definition of Parts supplier: 1. Parts marked with [MBI] in the remarks column are supplied from Matsushita Battery Industrial co., ltd. .
Ref. No. Part No. Part Name & Description Remarks
Ref. No. R8006 R8008 R8009 R8010 R8011 R8012 R8013 R8021 R8032 R8033 S8001 S8002 S8003 S8004 S8005 T8001
Part No. ERJ8GEYJ105V ERJ2GEJ432X ERJ2GEJ822 ERJ2GEJ822 ERJ2GEJ432X ERJ2GEJ242 ERJ2RHD153X ERJ2GEJ104 ERJ6RED105 ERJ6RED105 K0F212A00001 VSS0534 ESE23F101 K0F111A00472 K0G188A00002
Part Name & Description M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR SWITCH SWITCH SWITCH SWITCH SWITCH CH CH CH CH CH CH CH CH CH CH 1/8W 1M 1/16W 4.3K 1/16W 8.2K 1/16W 8.2K 1/16W 4.3K 1/16W 2.4K 1/16W 15K 1/16W 100K 1/16W 1M 1/16W 1M
Remarks
K0D112B00071
G5DYA0000100 TRANSFORMER
s ------ P.C.B. LIST -----MAIN C.B.A. (RTL) C3101 C3103 C3104 Q3102 R3101 R3102 R3105 R3108
CCD UNIT C.CAPACITOR CH 10V 1U C.CAPACITOR CH 16V 2.2U C.CAPACITOR CH 16V 0.01U TRANSISTOR NPN M.RESISTOR M.RESISTOR M.RESISTOR M.RESISTOR CH CH CH CH 1/16W 1/16W 1/16W 1/16W 33 2.2K 0 1M
VEP56021A
VEP58012A
(RTL)
VEK0H65
CCD UNIT
C8003 L8001
VEP56021A
Z9101
ML-614S/ZT
[MBI]
s C8001 C8002 C8004 C8005 C8006 C8008 C8010 D8002 D8003 D8004
FLASH TOP C.B.A. C.CAPACITOR C.CAPACITOR C.CAPACITOR C.CAPACITOR C.CAPACITOR C.CAPACITOR C.CAPACITOR CH 6.3V 1U 630V 0.033U 630V 1000P CH 6.3V 10U CH 250V0.033U CH 6.3V 10U CH 6.3V 10U
(RTL)
IC8001 C0ZBZ0001011 IC PS8001 K1KB30AA0116 CONNECTOR 30P Q8001 Q8002 Q8009 R8001 R8003 R8004 B1JBLP000008 TRANSISTOR B1DFGC000003 TRANSISTOR B1DFCG000010 TRANSISTOR ERJ3GEYJ242 M.RESISTOR CH 1/10W 2.4K ERJ6GEY0R00V M.RESISTOR CH 1/10W 0 ERJ2GEJ680 M.RESISTOR CH 1/16W 68
D0GBR00JA017 ERJ2RMJ680X
43