Professional Documents
Culture Documents
EIe Syllabus
EIe Syllabus
SYLLABUS
BACHELOR OF ENGINEERING PROGRAMME IN ELECTRONICS & INSTRUMENTATION ENGINEERING (8 SEMESTERS) REGULATIONS 2010
SATHYABAMA UNIVERSITY
Each semester curriculum shall normally have a blend of lecture courses not exceeding 7 and practical courses not exceeding 4. The medium of instruction, examinations and project report will be in English.
Duration of the Programme A student is normally expected to complete the B.E/B.Tech. Programme in 8 semesters but in any case not more than 12 consecutive semesters from the time of commencement of the course (not more than 10 semesters for those who join 3rd semester under Lateral entry system) The Head of the Department shall ensure that every teacher imparts instruction as per the number of hours specified in the syllabus and that the teacher teaches the full content of the specified syllabus for the course being taught.
3.
Requirements for Completion of a Semester A candidate who has fulfilled the following conditions shall be deemed to have satisfied the requirement for completion of a semester. 3.1 3.2 He/She secures not less than 90% of overall attendance in that semester. Candidates who do not have the requisite attendance for the semester will not be permitted to write the University Exams.
4.
Examinations The examinations shall normally be conducted between October and December during the odd semesters and between March and May in the even semesters. The maximum marks for each theory and practical course (including the project work and Viva Voce examination in the Eighth Semester) shall be 100 with the following breakup. (i) Theory Courses Internal Assessment : 20 Marks University Exams (ii) Practical Courses Internal Assessment : - University Exams : 100 Marks : 80 Marks
REGULATIONS 2010
SATHYABAMA UNIVERSITY
5.
Passing requirements (i) A candidate who secures not less than 50% of total marks prescribed for the course (For all courses including Theory, Practicals and Project work) with a minimum of 35 marks out of 80 in the University Theory Examinations, shall be declared to have passed in the Examination. If a candidate fails to secure a Pass in a particular course, it is mandatory that he/she shall reappear for the examination in that course during the next semester when examination is conducted in that course. However the Internal Assessment marks obtained by the candidate in the first attempt shall be retained and considered valid for all subsequent attempts.
(ii)
6.
Eligibility for the Award of Degree A student shall be declared to be eligible for the award of the B.E/B.Tech. degree provided the student has successfully completed the course requirements and has passed all the prescribed examinations in all the 8 semesters within the maximum period specified in clause 2.
7.
Award of Credits and Grades All assessments of a course will be done on absolute marks basis. However, for the purpose of reporting the performance of a candidate, Letter Grades will be awarded as per the range of total marks (out of 100) obtained by the candidate as given below:
i - Sum of all subjects successfully cleared during all the semesters 8. Classification of the Degree Awarded 1. A candidate who qualifies for the award of the Degree having passed the examination in all the courses of all the semesters in his/her first appearance within a maximum period of 8 consecutive semesters after commencement of study (maximum of 6 semesters for Lateral entry system who join the course in the third semester) securing a CGPA not less than 9.0 shall be declared to have passed the examination in First Class Exemplary.
ii REGULATIONS 2010
SATHYABAMA UNIVERSITY
2.
A candidate who qualifies for the award of the Degree having passed the examination in all the courses of all the semesters in his/her first appearance within a maximum period of 8 consecutive semesters after commencement of study (maximum of 6 semesters for Lateral entry system who join the course in the third semester) securing a CGPA not less than 7.5 shall be declared to have passed the examination in First Class with Distinction. A candidate who qualifies for the award of the Degree having passed the examination in all the courses of all the semesters within a maximum period of 8 consecutive semesters after commencement of study (maximum of 6 semesters for Lateral entry system who join the course in the third semester) securing a CGPA not less than 6.0 shall be declared to have passed the examination in First Class. All other candidates who qualify for the award of the Degree having passed the examination in all the courses of all the 8 semesters within a maximum period of 12 consecutive semesters (10 consecutive semesters for Lateral Entry system who join the course in the third semester) after his/her commencement of study securing a CGPA not less than 5.0 shall be declared to have passed the examination in Second Class. A candidate who is absent in semester examination in a course/project work after having registered for the same, shall be considered to have appeared in that examination for the purpose of classification of degree. For all the above mentioned classification of Degree, the break of study during the programme, will be counted for the purpose of classification of degree. A candidate can apply for revaluation of his/her semester examination answer paper in a theory course, within 1 week from the declaration of results, on payment of a prescribed fee along with prescribed application to the Controller of Examinations through the Head of Department. The Controller of Examination will arrange for the revaluation and the result will be intimated to the candidate concerned through the Head of the Department. Revaluation is not permitted for practical courses and for project work.
3.
4.
5.
6.
Minimum CGPA requirements for award of Degree is 5.0 CGPA. 9. Discipline Every student is required to observe disciplined and decorous behaviour both inside and outside the University and not to indulge in any activity which will tend to bring down the prestige of the University. If a student indulges in malpractice in any of the University theory / practical examination, he/she shall be liable for punitive action as prescribed by the University from time to time. 10. Revision of Regulations and Curriculum The University may revise, amend or change the regulations, scheme of examinations and syllabi from time to time, if found necessary.
B.E. (ELECTRONICS & INSTRUMENTATION) iii REGULATIONS 2010
SATHYABAMA UNIVERSITY
TOTAL CREDITS
SEMESTER II
Sl. No. SUBJECT CODE THEORY 1 2 3 4 5 6 7 PRACTICAL 1 2 SCSX4002 SEEX4001 Programming in C Lab Electrical Engineering Lab 0 0 0 0 4 4 2 2 26 16 16 SCHX1001 SMTX1002 SPHX1002 SCYX1002 SECX1001 SEEX1004 SCSX1002 Environmental Science and Engineering Engineering Mathematics II Applied Physics Chemistry of Electronic Materials Electronic Devices Electrical Technology Programming in C 3 3 3 3 3 2 3 0 1 0 0 0 1 0 0 0 0 0 0 0 0 3 4 3 3 3 3 3 9 10 11 12 13 14 15 SUBJECT TITLE L T P C Page No.
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SEMESTER III
Sl. No. SUBJECT CODE THEORY 1 2 3 4 5 6 7 PRACTICAL 1 2 SECX4020 SECX4021 Electric Circuits & Digital Lab Devices & Electronic Circuits Lab 0 0 0 0 4 4 2 2 27 24 24 SMTX1009 SCSX1014 SEEX1005 SMEX1013 SICX1004 SECX1002 SECX1012 Engineering Mathematics-III Object Oriented Programming Circuit Theory Solid & Fluid Mechanics Sensors & Transducer Digital systems Electronic Circuits-I 3 3 3 3 3 3 3 1 0 1 0 0 0 0 0 0 0 0 0 0 0 4 3 4 3 3 3 3 17 18 19 20 21 22 23 SUBJECT TITLE L T P C Page No.
TOTAL CREDITS
SEMESTER IV
Sl. No. SUBJECT CODE THEORY 1 2 3 4 5 6 PRACTICAL 1 2 SMEX4005 SECX4022 Thermal & Fluid Mechanics Lab Electronic Circuits-II Lab 0 0 0 0 4 4 2 2 23 31 31 SMTX1010 SECX1013 SMEX1011 SECX1004 SICX1002 SECX1005 Engineering Mathematics-IV Electronic Circuits-II Applied Thermodynamics Signals and Systems Electrical Measurements & Instrumentation Network Analysis & Synthesis 3 3 3 3 3 3 1 0 0 0 0 0 0 0 0 0 0 0 4 3 3 3 3 3 25 26 27 28 29 30 SUBJECT TITLE L T P C Page No.
TOTAL CREDITS
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SEMESTER V
Sl. No. SUBJECT CODE THEORY 1 2 3 4 5 6 7 PRACTICAL 1 2 SECX4027 SECX4002 Integrated Circuits & DSP Lab Measurements &Transducers Lab 0 0 0 0 4 4 2 2 28 39 39 SMTX1011 SECX1028 SECX1010 SICX1013 SICX1005 SICX1008 SEEX1010 Applied Numerical Methods Digital Signal Processing Linear Integrated Circuits Industrial and Chemical Processes Electronic Measurements & Instrumentation Industrial Instrumentation Control Systems 3 3 3 3 3 3 3 1 1 0 0 0 0 1 0 0 0 0 0 0 0 4 4 3 3 3 3 4 32 33 34 35 36 37 38 SUBJECT TITLE L T P C Page No.
TOTAL CREDITS
SEMESTER VI
Sl. No. SUBJECT CODE THEORY 1 2 3 4 5 6 PRACTICAL 1 2 SECX4028 SICX4003 Microprocessor & Microcontroller Lab Process Control Lab 0 0 0 0 4 4 2 2 23 44 44 SICX1006 SECX1015 SICX1007 SECX1048 Modern Control System Microprocessor & Micro controllers Process Control Fundamentals of Fuzzy logic & Artificial Neural Networks Elective-I Elective-II 3 3 3 3 3 3 1 0 0 0 0 0 0 0 0 0 0 0 4 3 3 3 3 3 40 41 42 43 SUBJECT TITLE L T P C Page No.
TOTAL CREDITS
vi
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SEMESTER VII
Sl. No. SUBJECT CODE THEORY 1 2 3 4 5 6 PRACTICAL 1 SICX4004 Industrial Instrumentation Lab 0 0 4 2 20 52 SBAX1001 SICX1010 SICX1009 Elective-III Elective-IV SECX1064 Data Acquisition and Communication Systems Principles of Management & Professional Ethics Computer Control of Process Biomedical Instrumentation 3 3 3 3 3 3 0 0 0 0 0 0 0 0 0 0 0 0 3 3 3 3 3 3 48 45 46 47 SUBJECT TITLE L T P C Page No.
TOTAL CREDITS
SEMESTER VIII
Sl. No. SUBJECT CODE 1 2 3 PRACTICAL 1 2 SICX4005 S18XPROJ System Design Lab Project Work & Viva-Voce 0 0 0 0 4 30 2 15 27 200 52 52 SECX1021 SICX1014 SICX1015 SUBJECT TITLE Fundamentals of VLSI design Logic & Distributed control system Analytical Instrumentation L 3 3 3 T 0 1 0 P 0 0 0 C 3 4 3 Page No. 49 50 51
vii
REGULATIONS 2010
SATHYABAMA UNIVERSITY
LIST OF ELECTIVES Note: ONE SUBJECT IS TO BE CHOSEN FROM EACH GROUP COMPULSORILY GROUP 1:
Sl. No. SUBJECT CODE 1 2 3 4 5 6 SICX1012 SICX1016 SICX1020 SICX1025 SICX1026 SICX1029 SUBJECT TITLE Software for System Design Fundamentals of Mechatronics Theory of Robotics & Automation Satellite Instrumentation Ultrasonic Instrumentation Process Control System Components L 3 3 3 3 3 3 T 0 0 0 0 0 0 P 0 0 0 0 0 0 C 3 3 3 3 3 3 Page No. 53 54 55 56 57 58
GROUP 2:
1 2 3 4 5 6 SICX1022 SICX1023 SICX1017 SICX1018 SICX1024 SICX1028 Digital Control Systems Adaptive Control System Instrumentation & Control in Petrochemical Industries Instrumentation & Control In Pulp & Paper Industries Instrumentation In Aerospace & Navigation Power Plant Instrumentation 3 3 3 3 3 3 0 0 0 0 0 0 0 0 0 0 0 0 3 3 3 3 3 3 59 60 61 62 63 64
GROUP 3:
1 2 3 4 5 6 SECX1040 SECX1041 SECX1042 SECX1047 SECX1059 SICX1019 Digital Image Processing Programming in MATLAB Advanced Electronics Test Engineering Embedded Systems Pattern recognition and Image vision Instrumentation & Control In Iron & Steel Industries 3 3 3 3 3 3 0 0 0 0 0 0 0 0 0 0 0 0 3 3 3 3 3 3 65 66 67 68 69 70
GROUP 4:
1 2 3 4 5 6 7 SCSX1021 SCSX1009 SEEX1013 SMEX1017 SICX1021 SECX1020 SECX1022 Artificial Intelligence Computer Architecture & Parallel Processing Power Electronics Resource Management Techniques Fiber optics & Laser Instrumentation Nano Electronics MEMS and its Applications 3 3 3 3 3 3 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 3 3 3 3 3 3 71 72 73 74 75 76 77
viii
REGULATIONS 2010
SATHYABAMA UNIVERSITY
C.
D.
E.
ix
REGULATIONS 2010
SATHYABAMA UNIVERSITY
CURRICULUM SUBJECTS FOR DUAL DEGREE PROGRAMME IN COMPUTER SCIENCE THIRD SEMESTER
Sl.No. THEORY 1 2 PRACTICALS 3 SCSX4004 Data Structures Lab 0 0 4 2 9 TOTAL CREDITS SCSX1004 SCSX1005 Software Engineering Data Structures & Algorithms 3 3 0 1 0 0 3 4 SUBJECT CODE NAME OF THE SUBJECT L T P C
FOURTH SEMESTER
THEORY 1 2 PRACTICALS 3 SCSX4005 Java Programming Lab 0 0 4 2 8 TOTAL CREDITS SCSX1007 SCSX1009 Java Programming Computer Architecture & Organization 3 3 0 0 0 0 3 3
FIFTH SEMESTER
THEORY 1 2 PRACTICALS 3 SCSX4011 RDBMS Lab 0 0 4 2 10 TOTAL CREDITS SCSX1017 SCSX1018 Data Communication and Computer Networks Database Systems 3 3 1 1 0 0 4 4
SIXTH SEMESTER
THEORY 1 2 PRACTICALS 3 SCSX4010 System Programming Lab 0 0 4 2 8 TOTAL CREDITS SCSX1019 SCSX1022 System Programming J2EE 3 3 0 0 0 0 3 3
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SEVENTH SEMESTER
THEORY 1 2 PRACTICALS 3 SCSX4006 C# and .Net Lab 0 0 4 2 9 SCSX1008 SCSX1011 C# and .Net Operating System 0 3 0 1 0 0 3 4
TOTAL CREDITS
EIGHTH SEMESTER
THEORY 1 2 3 PRACTICALS 4 SCSX4012 Network Programming Lab 0 0 4 2 11 SCSX1024 Network Programming & Management Elective I Elective II 3 3 3 0 0 0 0 0 0 3 3 3
TOTAL CREDITS
NINETH SEMESTER
THEORY 1 2 3 4 5 6 PRACTICALS 7 8 SCSX4014 SCSX4015 Hardware Peripherals Lab Case Tools & Testing Lab 0 0 0 0 4 4 2 2 22 SCSX1023 SCSX1030 SCSX1025 SCSX1027 Computer Systems Graphics & Multimedia 3 3 3 3 3 3 0 0 0 0 0 0 0 0 0 0 0 0 3 3 3 3 3 3
Datamining & Warehousing Wireless & Mobile Networks Hardware Peripherals and Interfacing Elective III Elective IV
TOTAL CREDITS
TENTH SEMESTER
1 S11XPROJ Project Work and Viva-Voce 0 0 30 15 15
xi
REGULATIONS 2010
SATHYABAMA UNIVERSITY
xii
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SHSX1001
L 3
T 0
P 0
Credits 3
UNIT I
10 hrs.
Reading comprehension- Skimming and Scanning - Transcoding -Bar diagram, Tables and Pie chart Discussing topics of general interest or on current topics and making a presentation in the class - Conjunctions and discourse markers- cloze reading- affixes definitions- tense- voice jumbled sentences.
UNIT II
10 hrs.
Subject verb agreement - Idioms and phrases, reading passages to answer evaluative, inferential and hypothetical type of questions- Listening - Creative thinking and speaking- Formal letters - application for job- resume preparationinviting dignitaries to department workshops, symposium and university functions - Letter to the editor.
UNIT III
10 hrs.
Reading and summarising reports - Writing a project proposal - Editing - Checking punctuation and grammatical errors- Types of Sentences preparation of Check List- formulating questions and answers - communicating politely.
UNIT IV
10 hrs.
Reported speech- Parts of speech- confusable words - Report on industrial visit - project report - Making effective Power Point presentations - speaking about the future plans-expressing opinions-reading and guessing meanings of unknown words from the context using appropriate verb forms
UNIT V
10 hrs.
Modal auxiliaries Presentation of problems and solutions wh- questions- question tags- punctuation- hyponymylistening and taking notes study skills preparing notes
SATHYABAMA UNIVERSITY
SMTX1001
ENGINEERING MATHEMATICS I
(Common to all branches except Bio Groups)
L 3
T 1
P 0
Credits 4
UNIT I TRIGONOMETRY
10 hrs.
Review of Complex numbers and De Moivres Theorem. Expansions of Sinn and Cosn; Sin and Cos in powers of , Sinn and Cosn in terms of multiples of . Hyperbolic functions Inverse hyperbolic functions. Separation into real and imaginary parts of complex functions
UNIT II MATRICES
10 hrs.
Characteristic equation of a square matrix - Eigen values and Eigen vectors of a real matrix- properties of Eigen values and Eigen vectors, Cayley-Hamilton theorem (without proof) verification Finding inverse and power of a matrix. Diagonalisation of a matrix using similarity transformation (concept only) , Orthogonal transformation Reduction of quadratic form to canonical form by orthogonal transformation.
10 hrs.
Curvature centre, radius and circle of curvature in Cartesian co-ordinates only Involutes and evolutes envelope of family of curves with one and two parameters properties of envelopes and evolutes evolutes as envelope of normal.
10 hrs.
Functions of two variables partial derivatives Eulers theorem and problems - Total differential Taylors expansion Maxima and minima Constrained maxima and minima Lagranges multiplier method Jacobian Differentiation under integral sign.
10 hrs.
Second order linear differential equation with constant coefficients Particular Integrals for e , sin ax, cos ax, xn, xneax, eax sinbx, eax cos bx. Equations reducible to Linear equations with constant co-efficient using x=et. Simultaneous first order linear equations with constant coefficients - Method of Variations of Parameters.
SATHYABAMA UNIVERSITY
SPHX1001
PHYSICS OF MATERIALS
(Common to all Branches of B.E / B.Tech)
L 3
T 0
P 0
Credits 3
10 hrs.
Classical Free electron theory of Metals-Derivation of Electrical and Thermal Conductivity- Deduction of Wiedemann Franz law-Lorentz number. Introduction to Band theory, Difference between Conductors, Semiconductors and Insulators - Superconductivity-Transition temperature - occurrence of superconductivity - BCS Theory(Qualitative), properties of superconductors -Type I &Type II superconductors, High Tc superconductors, AC & DC Josephson effects. Applications of superconductors basic concepts of SQUID, cryotron, magnetic levitation.
10 hrs.
Types based on spin. Hard and soft magnetic materials, domain theory of Ferromagnetism, magnetic bubbles, formation and propagation of magnetic bubbles, applications of magnetic materials - Magnetic storage devices. Dielectric parameters, polarization, polarisability, types of polarization. Internal or local electric field - derivation of Lorentz Equation and Clausius - Mossotti Equation, dielectric loss and breakdown, types of dielectric breakdown, types of dielectric materials, applications.
10 hrs.
Optical processes and Excitons - types, Traps - Trapping and recombination, types, Point defects Frenkel and Schottky defects - Colour centers - types and their mechanisms, Luminescence - Photoluminescence - TypesFluorescence and Phosphorescence- Mechanism and its applications, Cathodoluminescence, Electroluminescence. Non-linear Optical Materials Basic Principle, Classifications, Properties - Frequency Doubling or Tripling, Optical Mixing - Applications.
10 hrs.
Metals and alloys steel and its properties - Iron-carbon phase diagram, Titanium and Aluminium based alloys - Introduction, properties and Applications. Shape Memory Alloys (SMA) - Principle of shape memory effects, Hysteresis curve, Two way shape memory alloys, super-elasticity and thermo-mechanical behavior. Characterization methods to identify the phase transformation of SMA, commercial SMA Ni-Ti alloys, copper alloys and Cu-Al alloys, Applications. Ceramics Classification, Properties, fabrication, advanced ceramics and applications. Composites particle reinforced composites and fiber reinforced composites processing and applications.
10 hrs.
Structural characterization X-ray diffraction, electron diffraction and neutron diffraction Determination of crystal structure. Difference among these diffraction techniques.Micro structural characterization optical microscope, scanning electron microscope, transmission electron microscope, atomic force microscopy, micro and nano hardness testing principle and applications.
REFERENCE BOOKS :
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Ragavan.V, Material science and Engineerimg, 5th Edition, Eastern Eco, 2004. Suresh.R and Jayakumar.V, Materials Science, 1st Edition, Lakshmi Publication, 2003. Wilson.J and Hawkes.J.F.B, Optoelectronics- An Introduction, 2nd Edition, Prentice-Hall of India, 2001. Dr.Arumugam M., Semiconductor Physics and Opto electronics, 1st Edition, Anuradha Publishers, 2003. Gaur.R.K and Gupta.S.L, Engineering Physics, 8th Edition, Dhanbat Rai Publications,2007. Palanisamy.P.K, Engineering Physics, 1st Edition, SCITECH Publications, 2007. Sankar.B.N and Pillai.S.O, A text book of Engineering Physics, 1st Edition, New Age international Publishers, 2007. Rajendran.V, Engineering Physics, 2nd Edition, Tata McGraw-Hill, 2008. Avadhanulu.M.N and P.G. Kshirsagar.P.G, Engineering Physics, 2nd Edition, S. Chand & Company, 2007. Dr. Arumugam M., Engineering Physics, 2nd Edition, Anuradha Publications, 2002. William D.Callister,Jr, Materials Science and Engineering An introduction, 6th Edition, John-Wiley and Sons,2004. Cullity.B.D, Principles of X-ray diffraction, 3rd Edition, Prentice Hall, 2001
UNIVERSITY EXAM QUESTION PAPER PATTERN Applications mentioned in the syllabus refer to the basic applications and not to any specific case.
Max. Marks: 80 Part A: 2 Questions from each unit, each carrying 2 marks Out of 20 marks, maximum of 10% problems may be asked. Part B: Questions from each unit with internal choice, each carrying 12 marks Out of 60 marks, maximum of 10% problems may be asked
B.E. (ELECTRONICS & INSTRUMENTATION) 3
SATHYABAMA UNIVERSITY
SCYX1001
ENGINEERING CHEMISTRY
(Common to All Branches)
L 3
T 0
P 0
Credits 3
10 hrs.
Introduction: Impurities present in water, Hardness: Types of hardness, Expression, Units. Estimation of hardness by EDTA method, Problems. Boiler Troubles: Sludge & Scales, Boiler Corrosion. Water Softening: Zeolite process, Demineralization process, Merits and Demerits. Reverse osmosis, Merits and Demerits. Domestic water treatment: Flow chart diagram only.
10 hrs.
Introduction - Battery terminology: Primary cells, Secondary batteries, Charging and Discharging characteristics, Capacity, Energy density, Cycle life, Internal resistance. Secondary batteries: Lead-acid accumulator, Nickel-cadmium batteries , Lithium primary cells: Lithium-thionyl chloride cell, Lithium-iodine cell. Lithium secondary batteries: Lithium-ion batteries. Fuel cells: Hydrogen-Oxygen fuel cell, Solid oxide fuel cell (SOFC): Principle, construction, anode cathode and electrolyte. Proton Exchange Membrane Fuel Cell.
10 hrs.
Introduction - Electrochemical cell representation. Electrochemical series: Significance. Galvanic series. Corrosion: Definition of corrosion, Dry corrosion: Mechanism of Dry corrosion, Pilling-Bedworth rule, Wet Corrosion: Mechanism. Types of corrosion: Galvanic corrosion, Differential aeration corrosion, Pitting corrosion, Microbial Corrosion. Factors influencing corrosion: Nature of the metal, nature of the environment. Corrosion control: Material selection and Design, Cathodic protection. Corrosion inhibitors: Anodic, cathodic and Vapour phase inhibitors.
10 hrs.
Introduction - Explosives: Requirements, Classification of Explosives: Low explosives, primary explosives and high explosives. Assessment of explosives. Rocket engines: Types of rocket engines. Basic principle, Mass fraction, Specific impulse, Thrust, Effective exhaust velocity, Specific propellant consumption. Chemical propellants: Requirements, Classification: Liquid fuels, Liquid oxidizers, Solid fuels, Solid oxidizers.
10 hrs.
Introduction. Adsorption: Types, Adsorption of gases on solids, Adsorption of solutes from solution. Adsorption isotherms: Freundlich adsorption isotherm, Langmuir adsorption isotherm. Industrial adsorbent materials: Role of adsorbents in catalysis and water softening. Emulsion: Types: water/oil, oil/water. Applications of adsorption: Cottrells precipitator, Coating of rubber on metals, Electrostatic painting.
60 marks
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SMEX1001
ENGINEERING GRAPHICS
(Common to all Branches of B.E / B.Tech)
L 1
T 2
P 0
Credits 3
10 hrs.
Introduction - Importance of graphics in engineering applications Use of drafting instruments BIS specifications and conventions Size, layout and folding of drawing sheets Lettering and dimensioning- Polygons used in engineering practice methods of construction of pentagon and hexagon Construction of ellipse, parabola and hyperbola.
10 hrs.
General principles of orthographic projection first angle projection layout of views projections of points, straight lines located in the first quadrant Determination of true lengths of lines and their inclinations to the planes of projection Traces
10 hrs.
Projection of solids like prism, pyramid, cylinder and cone when the axis is inclined to only one plane of projection Change of position method only - Sectioning of above mentioned solids in simple vertical positions by cutting plane inclined to one reference plane and perpendicular to the other True shapes of sections
10 hrs.
Need for development of surfaces Development of lateral surfaces of simple and truncated solids Prisms, pyramids, cylinders and cones.- Pictorial representation of engineering objects Representation of three dimensional objects in two dimensional media Need for multiple views Developing visualization skills through free hand sketching of three dimensional objects.
10 hrs.
Principles of isometric projection Isometric scale Isometric projections of simple solids and combination of solids - Prisms, pyramids, cylinders, cones and spheres (excluding isometric projections of truncated solids) - Perspective projections - Simple objects like cube, prisms, pyramids by Vanishing point method & Visual Ray method (excluding perspective projections of truncated solids)
60 marks
SATHYABAMA UNIVERSITY
L 3
T 0
P 0
Credits 3
8 hrs.
Alternate sources of energy - solar, wind, wave, tidal and geo-thermal. Boilers: Classification and principles of modern high pressure steam generators -Layout and working principles of hydraulic (hydel), steam, gas turbine, diesel and nuclear power plants.
8 hrs. 9 hrs.
Working principle of petrol and diesel engines - Two stroke and four stroke engines - Ignition systems -single jet carburetor-spark plug-cooling systems- lubrication systems - fuel pump and fuel injector. Foundry process and technology: Foundry tools, pattern, moulding process. Metal forming processes: Principles of forging, rolling, drawing and extrusion. Metal joining process: Principles of welding - fundamentals of arc welding, gas welding and gas cutting - brazing and soldering. Metal machining process: Lathe -Specifications - Main components and their functions-Lathe operations. Machining Concept - Drilling, Milling, Turning, Grinding and surface Finishing.
8 hrs.
Construction materials - Physical and Mechanical properties - stone, brick, cement, concrete, bitumen, insulation materials & steel. Buildings - various components and their functions. Foundation - functions - classification and suitability. Flooring - function - types - cement concrete, tile, marble and granite flooring. Masonry - Stone and Brick masonry and construction details. Roof - Types - Flat & sloped RCC roof. Introduction to seismic resistant structures.
8 hrs.
Stress, strain & modulus of elasticity. Simple maintenance methodologies, Valuation - plinth area method depreciation rate method. Land development process - Set backs, Authorities involved. Basics of interior design and landscaping. Introduction to Orientation of the building & Energy efficient buildings.
9 hrs.
Importance of Transport - Roads - Classification of roads - Traffic signs & signals - Surveying - Classification and principles - Applications of Theodolite and Total Station - Measurements of distances - angle - Computation of areas - Trapezoidal and Simpsons rule.
Part A: 5 questions of 2 marks each - no Choice Part B: 3 questions from each of the three units of internal choice, each carrying 10 marks Basic Civil Part A: 5 questions of 2 marks each - no Choice Part B: 3 questions from each of the three units of internal choice, each carrying 10 marks.
B.E. (ELECTRONICS & INSTRUMENTATION) 6
SATHYABAMA UNIVERSITY
SEEX1001
L 2
T 1
P 0
Credits 3
12 hrs.
Electrical quantities, Ohms Law, Resistors - Series and parallel combinations, Kirchoffs laws, Node and Mesh Analysis, Star delta Transformation
10 hrs.
Definition of MMF, Flux and reluctance - Leakage factor - Reluctances in series and parallel (series and parallel magnetic circuits) - Electromagnetic induction - Flemings rule - Lenzs law - Faradays laws - statically and dynamically induced EMF - Self and mutual inductance - Analogy of electric and magnetic circuits.
12 hrs.
Sinusoidal functions - RMS(effective) and Average values - Phasor representation - J operator - sinusoidal excitation applied to purely resistive - inductive and capacitive circuits - RL - RC and RLC series and parallel circuits - power and power factor -Three phase circuits - Star / Mesh connections with balanced loads - measurement of power by two wattmeter method.
8 hrs.
Classification, essentials of indicating instruments, Moving coil and moving iron instruments - Voltmeter, Ammeter, Wattmeter - Principle and theory of operation - Induction type energy meter - Earth Megger.
8 hrs.
Domestic Wiring - Materials and accessories - Types of wiring - Stair case wiring, Fluorescent tube circuit Earthing - Indian Electricity rules for wiring - Simple domestic wiring layout - Single line diagram of Transmission and Distribution Systems - Dos and Donts of electrical safety.
TEXT BOOKS:
1. Mittle B.N., Aravind Mittle, "Basic Electrical Engineering", Tata McGraw Hill", 2nd Edition Sep 2005. 2. Theraja B.L., "Fundamentals of Electrical Engineering and Electronics", S.Chand & Co., First Multi colour Edition, 2006, (Reprint 2009).
REFERENCE BOOKS:
1. 2. 3. 4. 5. Smarajit Ghosh, "Fundamentals of Electrical and Electronics Engineering", PHI Learning Private Ltd, 2nd Edition, 2010. Wadhwa C.L., "Basic Electrical Engineering", New Age International, 4th Edition, 2007, Reprint June 2010. Abhijit Chakrabarti, Sudipta nath & Chandan Kumar Chanda, "Basic Electrical Engineering", Tata McGraw Hill, 1st Edition, 2009. Thyagarajan T., "Fundamentals of Electrical and Electronics Engineering", Sci Tech Publications, 5th Edition, Reprint Jan 2010. TNEB Power Engineers Hand Book.
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SPHX4001
L 0
T 0
P 2
Credits 1
Total Marks 50
1. 2. 3. 4. 5. 6.
Torsional pendulum- Determination of MI of the disc and rigidity modulus of the wire. Quinckes method - Determination of magnetic susceptibility of a liquid Semiconductor diode - Determination of width of the forbidden energy gap Ultrasonic interferometer Determination of Compressibility of liquid Lees disc - Determination of thermal conductivity of a bad conductor. Optical Fiber Determination of Numerical aperture and attenuation loss.
SCYX4001
L 0
T 0
P 2
Credits 1
Total Marks 50
1. 2. 3. 4. 5. 6.
Determination of total, permanent and temporary hardness of a water sample. Estimation of copper in an ore by iodometric titration. Determination of strength of HCl by conductometric titration. Estimation of the amount of ferrous ion by titrating with chromate ion using potentiometer. Verification of the Freundlich isotherm by using acetic acid adsorption on charcoal. Determination of the rate of corrosion of iron metal by hydrogen evolution method.
SPRX4001
L 0
T 0
P 4
Credits 2
CARPENTRY
Handling of carpentry tools, A practice in marking, sawing planning and chiseling to size. Making simple joints such as half-lap, dove-tail and mortise and tenon joints. Use of modern materials such as plywood, chip board, novapan, laminated sheet (demonstration only).
FITTING
Use of fitting tools-practice in marketing, fitting to size and drilling-making of simple mating and profiles such as V, Square, Dove-tail, Half-round joints.
WELDING
i. Electric Arc Welding a) Study on Edge preparation techniques for Arc welding b) List of Welding Exercises 1. Lap Joint 2. Butt Joint 3. Fillet Joint 4. Tee Joint 5. V Joint 6. Corner Joint ii. Study on gas welding and gas cutting iii. Study on TIG & MIG welding
FOUNDRY
i. Sand testing - Grain fineness - Permeability test. ii. Study on Pattern Allowances iii. Preparation of green sand moulding 1. Flanges 2. Glands 3. Bush 4. Dumbbell iv. Metal casting technique (Demonstration only)
B.E. (ELECTRONICS & INSTRUMENTATION) 8 REGULATIONS 2010
SATHYABAMA UNIVERSITY
SCHX1001
L 3
T 0
P 0
Credits 3
12 hrs.
Definition, scope and importance - need for public awareness - forest resources: use and over-exploitation, deforestation, case studies. Timber extraction, mining, dams, floods, drought, conflicts over water, dams-benefits and problems - mineral resources: use effects on forests and tribal people - water resources: use and over-utilization of surface and ground water - exploitation, environmental effects of extracting and using mineral resources, case studies - food resources: world food problems, changes caused by agriculture and overgrazing, effects of modern agriculture, fertilizer-pesticide problems, water logging, salinity, case studies - energy resources: growing energy needs, renewable and non renewable energy sources, use of alternate energy sources. Case studies - land resources: land as a resource, land degradation, man induced landslides, soil erosion and desertification - role of an individual in conservation of natural resources - equitable use of resources for sustainable lifestyles.
12 hrs.
Concept of an ecosystem - structure and function of an ecosystem - producers, consumers and decomposers - energy flow in the ecosystem - ecological succession - food chains, food webs and ecological pyramids - introduction, types, characteristic features, structure and function of the (a) forest ecosystem (b) grassland ecosystem (c) desert ecosystem (d) aquatic ecosystems (ponds, streams, lakes, rivers, oceans, estuaries) - introduction to biodiversity definition: genetic, species and ecosystem diversity - biogeographical classification of India - value of biodiversity: consumptive use, productive use, social, ethical, aesthetic and option values - biodiversity at global, national and local levels - India as a mega-diversity nation - hot-spots of biodiversity - threats to biodiversity: habitat loss, poaching of wildlife, man-wildlife conflicts - endangered and endemic species of India - conservation of biodiversity: in-situ and ex-situ conservation of biodiversity.
10 hrs.
Definition - causes, effects and control measures of: (a) air pollution (b) water pollution (c) soil pollution (d) marine pollution (e) noise pollution (f) thermal pollution (g) nuclear hazards - solid waste management: causes, effects and control measures of urban and industrial wastes - role of an individual in prevention of pollution - pollution case studies - disaster management: floods, earthquake, cyclone and landslides.
8 hrs.
From unsustainable to sustainable development - urban problems related to energy - water conservation, rain water harvesting, watershed management - resettlement and rehabilitation of people; its problems and concerns, case studies - environmental ethics: issues and possible solutions - climate change, global warming, acid rain, ozone layer depletion, nuclear accidents and holocaust, case studies. - wasteland reclamation - consumerism and waste products - environment protection act - air (prevention and control of pollution) act - water (prevention and control of pollution) act - wildlife protection act - forest conservation act - issues involved in enforcement of environmental legislation public awareness.
8 hrs.
Population growth, variation among nations - population explosion - family welfare programme - environment and human health - human rights - value education - HIV / AIDS - women and child welfare - role of information technology in environment and human health - case studies. Visit to a local area to document environmental assets-river/forest/grassland/hill/mountain. Visit to a local polluted site-urban/rural/ industrial/agricultural-study of common plants, insects, birds-study of simple ecosystems-pond, river, hill slopes etc.
SATHYABAMA UNIVERSITY
SMTX1002
ENGINEERING MATHEMATICS II
(Common to all branches Except BIO Groups)
L 3
T 1
P 0
Credits 4
10 hrs.
Relation between roots and Co-efficient of equations Symmetry function of roots Formation of equations To increase or decrease the roots of a given equation by a given quantity Reciprocal equations Descartes rule of signs Cardons method of solving cubic equations.
10 hrs.
Direction cosines and ratios The equation of a plane Equation to a straight line Shortest distance between two skew lines Coplanar lines Sphere Tangent line Plane section of a sphere Orthogonal spheres.
10 hrs.
Double integrals Change of order of integration Change of Variables from Cartesian to Polar coordinates Area - using double integral - Triple integrals - Volume using Triple integrals.
10 hrs.
Properties of definite Integrals Related definite Integrals Reduction formulae for e , x sinax, xn cos ax, sin x, cosnx and sinm x cosn x. Definitions of Beta and Gamma integrals Relation between them Properties Evaluation of definite integrals in terms of Beta and Gamma function Simple applications.
10 hrs.
Differentiation of a vector function Gradient, divergence and curl Directional derivative Identities (without proof) - Irrotational and Solenoidal fields, Vector Integration Line, Surface and Volume Integrals, Integral theorems (without proof), Greens theorem (in the plane), Gauss divergence theorem and Stokes theorem Simple applications involving rectangles and cuboids.
SATHYABAMA UNIVERSITY
SPHX1002
APPLIED PHYSICS
(Common For All Branches)
L 3
T 0
P 0
Credits 3
10 hrs.
Introduction - Principle and structure of optical fibers-Acceptance angle-Numerical aperture-Types of optical fibers-Preparation of fiber Double crucible technique-Types of rays-Theory of propagation of light-Energy loss in optical fiber- Attenuation and distortion-Fiber splicing Fusion and mechanical splicing-Fiber connectors -Butt joint and expanded beam connectors-Optical fiber communication system (block diagram) - Advantages and its applications.
10 hrs.
Introduction Musical sound & noise-Characteristics of musical sound : pitch, loudness, quality Weber-Fechner law-Relation between pitch & frequency-Factors on which intensity & loudness depend-Decibel scale-Sound intensity level and sound pressure level-Sound absorption-OWU-Sound absorption coefficient and its measurements Reverberation - Reverberation time Standard Reverberation time Sabines formula to determine the Reverberation time (Jaegar method)- Factors affecting the acoustics of a building and the remedies-Principles to be followed in the acoustical design of a good auditorium.
10 hrs.
Number systems - Binary, decimal, Hexadecimal and Octadecimal-Conversion from one number system to another-Binary addition-Subtraction - Subtraction by 1s & 2s complement- BCD-ASCII-Excess 3 code and gray code.
10 hrs.
Definition-Fabrication-Top down approach and bottom up approach-Nanomagnets Particulate Nanomagnets, Geometrical Nanomagnets-Magneto Resistance Ordinary Magneto Resistance, Giant Magneto Resistance, Tunneling Magneto Resistance- Probing Nanomagnetic Materials-Nanomagnetism in Technology-Nano Devices Injection Laser Quantum Cascade Laser Optical Memories and Coulomb Blockade Devices
10 hrs.
Ultrasonics Introduction- Production of ultrasonic waves - Piezo-electric method-properties-Doppler effect - Blood flow meter Determination of upward and downward transit time- A- scan, B-scan and M-scan-X-rays Introduction-Units of X-rays- Diagnostic technologies of X-rays Radiography-Fluoroscopy-Image intensifier-Nuclear medicine Introduction-units of radioactivity, 99 m Tc generator, nuclear medicine imaging devices - Gamma camera.
REFERENCE BOOKS :
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Mathur.D.S, Heat and Thermodynamics, 5th Edition, Sultan Chand & Sons, 2004. Gerd Keiser, Optical fiber communication, 3rd Edition, Tata Mc Graw Hill, 2000. John M. Senior, Optical fiber communications - Principle and Practice, 2nd Edition, Pearson Education, 2006. Franz J.H, Jain V.K, Optical communication Components and Systems, 1st Edition, Narosa Publications, 2001. Malvino,Leach & Gautam Saha, Digital Principles and applications, 6th Edition, McGraw Hill, 2006. William H. Gothman, Digital electronics An Introduction to theory and practice, 2nd Edition, PHI of India, 2007. Roy, Medical Bio Physics, 1st Edition, Saras Publications, 2001. Vasantha Pattabhi, Bio Physics, 1st Edition, Narosa, 2004. Gaur. R.K. and Gupta. S.L., Engineering Physics, 8th Edition, Dhanbat Rai Publications,2007. Avadhanulu. M.N. and. Kshirsagar. P.G, Engineering Physics, 2nd Edition, S. Chand & Company, 2007. Dr. Arumugam M., Engineering Physics, 2nd Edition, Anuradha Publications, 2002. William D.Callister, Jr, Materials Science and Engineering An introduction, 6th Edition, John-Wiley and Sons, 2004.
60 marks
SATHYABAMA UNIVERSITY
SCYX1002
L 3
T 0
P 0
Credits 3
10 hrs.
Introduction - Functionality of monomer and its significance. Types of Polymerisation: Addition, Condensation and Copolymerisation. Plastics: Thermoplastics, Thermosetting plastics. Moulding constituents of plastics. Moulding methods: Compression moulding, Injection moulding, Extrusion moulding. Conducting polymers: definition, Examples with applications of Polyacetylene and Polyaniline. Optical fibers: Definition, Principle.Plastic optical fibers: Polymethyl methacrylate, Perfluorinated polymers. Biodegradable polymers: Definition, Classification and application.
10 hrs.
Introduction - Nanomaterials: definition, properties. Types: Nanoparticles, Synthesis by Chemical reduction method. Nanoporous materials: Synthesis by Sol-gel method. Nanowires: Synthesis by VLS mechanism. Carbon Nanotubes: Singlewalled and multiwalled nanotubes. Mechanical and electrical properties .Applications. Synthesis: Electric arc discharge method , Physical Vapour Deposition (PVD), Chemical Vapour Deposition (CVD), Laser Ablation method.
10 hrs.
Beer - Lamberts law. Spectrophotometer: Principles, Instrumentation (block diagram only). DSC, X - ray Diffractometer, TGA, DTA, SEM: Principle, block diagram and applications. Sensors: Oxygen sensor and Glucose sensor.
10 hrs.
Magnetic materials: Introduction. Types: Ferro magnetic, Ferri magnetic, Antiferro magnetic, Para and diamagnetic materials with examples. Magnetically soft and hard materials. Insulating materials: Classification: Heat Insulating materials, Characteristics. Types: Organic and inorganic insulators. Sound Insulating materials: Characteristics, Types: Soft, Semi-hard and Hard materials. Electrical Insulating materials (dielectrics): Characteristics, Types: Solid, Liquid and Gaseous materials.
10 hrs.
Electronic Materials: Types of Semiconductors: Intrinsic and Extrinsic Types, Non-Elemental semi-conducting materials. Preparation of Pure Ge/ Si: Distillation, Zone Refining, Czochralski Crystal Pulling Technique, Doping Techniques, Epitaxy, Diffusion and Ion- Implantation Techniques. Applications.
SATHYABAMA UNIVERSITY
SECX1001
ELECTRONIC DEVICES
(Common to EEE, ECE, E&C, EIE, ETCE & BIO-MED)
L 3
T 0
P 0
Credits 3
10 hrs.
Intrinsic and Extrinsic semiconductor - Charge density, Mobility and Conductivity in Semiconductor, Drift and diffusion current, Continuity equation, Hall effect - PN junction - Energy band diagram of PN junction, Current components in PN junction, Junction capacitance - Application of diode - Diode switch, Clipper, Clamper and Voltage multipliers - Zener diode - Zener voltage regulators.
10 hrs.
Construction and Operation of NPN and PNP transistor - Current components in a transistor, Eber molls Equation -Characteristics of CE,CB,CC configuration - Base width modulation, Transistor breakdown, Transistor biasing - Bias Stabilization and Compensation, Thermal runway problems, Heat sinks, Switching characteristics.
10 hrs.
JFET- Construction, Operation and Characteristics, Expression for pinch off voltage and drain current - MOSFET - Enhancement and Depletion mode operation and characteristics, Handling precautions of MOSFET, Gate capacitance - FET as VVR - Comparison of MOSFET and JFET - Comparison of BJT and JFET.
10 hrs.
SCR- UJT- Diac- Triac - Varactor diode - PIN diode - Tunnel diode - Gunn diode - Principle of photo electronic devices - Solar cell, Photo diode and Photo transistor - LED, LCD, LASER diode, CCD - Operation, Characteristics and Applications.
10 hrs.
Force on charged particle in electric field and magnetic field - Motion of charged particle in electric and magnetic field - Principles of CRT - Deflection and focusing of electron beam in CRT and TV picture tube-Orientation of electric and magnetic field in CRT - Applications of CRO.
TEXT BOOKS:
1. Millman and Halkias, Electronic devices and circuits, 2nd Edition, McGraw Hill Publication, 2007. 2. G.K.Mithal, Basic Electronic Devices and circuits, 2nd Edition, G.K.Publishers Pvt. Ltd., 1998.
REFERENCE BOOKS:
1. 2. 3. 4. David Bell,Fundamentals of Electronic Devices and Circuits, 5th Edition, Oxford University Press 2008. Robert L. Boylestad, Electronic Devices and Circuit Theory, 6th Edition, PHI, 1998. Ben G Streetman and Sanjay Banerjee, Solid State Electronic Devices, 6th Edition, Pearson Education, 2005. Roody and Coolen, Electronic Communications, 4th Edition, Pearson Education, Reprint 2007.
SATHYABAMA UNIVERSITY
SEEX1004
ELECTRICAL TECHNOLOGY
(Common to ECE, E&C , EIE, ETCE, MECH & M&P)
L 2
T 1
P 0
Credits 3
UNIT I DC GENERATORS
11 hrs.
Construction- Principle of operation - EMF equation types - performance characteristics- losses in dc generator - calculation of efficiency - Applications.
UNIT II DC MOTORS
10 hrs.
Construction - Principle of operation - Significance of Back EMF - Types - Performance characteristics - Torque Equation - Losses in dc motors - Calculation of efficiency - Starters - Necessity and their types - Speed control of various types of DC motors - Applications.
11 hrs.
Constructional details and principle of operation of single phase transformer - EMF equation - Phasor diagram on no load and loaded transformer - Equivalent circuit - Open circuit and Short circuit test on transformer - Regulation and Efficiency - All day efficiency - Auto transformer.
10 hrs.
Constructional details of three phase induction motor - Slip ring and squirrel cage rotor- principle of operationTorque equation - torque / slip characteristics - starters-Applications Introduction to single phase Induction motors - Capacitor start capacitor run motor -Shaded pole motor.
8 hrs.
Constructional features of Alternator - principle of operation - EMF equation - Regulation - Regulation by synchronous impedance method - Application, Constructional features of synchronous motor - principle of operation V and "inverter V" curves, starting and hunting - Applications. Special Machines: Stepper motor, AC and DC servomotor - Construction, working and applications.
TEXT BOOKS:
1.B.L.Theraja & A.K.Theraja, "A Text Book of Electrical Technology, Vol II", S.Chand & Company Ltd., 2009. 2.J.B. Gupta, " Theory and Performance of Electrical Machines", S.K.Kataria & Sons, 4th Edition, 2006
REFERENCE BOOKS:
1.R.K. Rajput, "Electrical Engineering", Lakshmi Publications Pvt Limited, 4th Edition, 2008 2.S.K.Bhattacharya, "Electrical Machines", Tata Mc Graw Hill Company Ltd, 3rd Edition, 2008. 3.D.P.Kothari & I.J.Nagrath, "Electrical Machines", Tata Mc Graw Hill Company Ltd, 3rd Edition, 2004, 12th Reprint.
SATHYABAMA UNIVERSITY
SCSX1002
PROGRAMMING IN C
(Common to all Branches of B.E / B.Tech.)
L 3
T 0
P 0
Credits 3
UNIT I INTRODUCTION
10 hrs.
Introduction: Algorithms & flowcharts-Overview of C-Features of C-IDE of C Structure of C program-Compilation & execution of C program-Identifiers, variables, expression, keywords, data types, constants, scope and life of variables, local and global variables. Operators: arithmetic, logical, relational, conditional and bitwise operators- Special operators: size of () & comma (,) operator-Precedence and associativity of operators & Type conversion in expressions. Basic input/output and library functions: Single character input/output i.e. getch(), getchar(), getche() & putchar()-Formatted input/output: printf() and scanf()-Library Functions: concepts, mathematical and character functions.
10 hrs.
Control structures: Conditional control-Loop control and Unconditional control structures. Functions: The Need of a function-User defined and library function- Prototype of a function-Calling of a function-Function argument-Passing arguments to function- Return values-Nesting of function- main()-Command line arguments and recursion. Storage class specifier auto, extern, static, & register.
10 hrs.
Arrays: Single and multidimensional arrays-Array declaration and initialization of arrays-Array as function arguments. Strings: Declaration-Initialization and string handling functions. Structure and Union: Defining structure-Declaration of structure variable-Accessing structure members-Nested structures-Array of structures-Structure assignment-Structure as function argument-Function that returns structure- Union.
UNIT IV POINTERS
10 hrs.
Pointers: The & and * operators-Pointers expressions-Pointers vs arrays-Pointer to functions-Function returning pointers-Static and dynamic memory allocation in C. DMA functions: malloc(), calloc(), sizeof(), free() and realloc()-Preprocessor directives.
10 hrs.
File management: Defining, opening & closing a file, text file and binary file- Functions for file handling: fopen, fclose, gets, puts,fprint, fscanf, getw, putw, fputs, fgets, fread, fwrite-Random access to files: fseek, ftell, rewind-File name as Command Line Argument. Graphics in PC-Initialize Graphics Mode-Functions used In Graphics - Drawing a Point on the Screen-Drawing lines, rectangles, ovals, circles, arcs, polygon, filling colors-Using Text in Graphics Display.
REFERENCE BOOKS:
1. 2. 3. 4. 5. 6. Balaguruswami.E, Programming in C, TMH Publications,1997 Behrouz A. Forouzan & Richard F. Gilberg, Computer Science A Structured Programming using C, Cengage Learning, 3rd Edition, 2007 Gottfried , Programming with C, schaums outline series, TMH publications,1997 Mahapatra , Thinking in C, PHI publications, 2nd Edition. Stevens , Graphics programming in C, BPB publication,2006 Subbura.R , Programming in C, Vikas publishing, 1st Edition, 2000
SATHYABAMA UNIVERSITY
SCSX4002
PROGRAMMING IN C LAB
L 0
T 0
P 4
Credits 2
1. To write a simple menu driven calculator program using switch statement. 2. To write a program to calculate the nCr using functions. 3. To write a program to find the largest and smallest number using arrays. 4. To write a program to generate Fibonacci series. 5. To write a program to find the factorial of a number using recursion. 6. To write a program to print the sum of elements of an array using pointers. 7. To write a program to implement file handling 8. To write a program to perform matrix addition and multiplication. 9. To write a program to check for perfect number. 10. To write a program to implement string manipulation functions without using library functions. 11. To write a program to perform ASCII equivalent keystrokes. 12. To write a program to solve a polynomial equation.
SEEX4001
L 0
T 0
P 4
Credits 2
1. 2. 3. 4. 5. 6. 7. 8. 9.
Open circuit characteristics of separately excited dc shunt generator. Load characteristics of self excited dc shunt generator Load characteristics of dc Compound generator Load characteristics of dc shunt motor Speed control of dc shunt motor. Load characteristics of dc series motor Open circuit and short circuit test on single phase transformer. Load test on single phase transformer Brake load test on three phase squirrel cage induction motor
10. Regulation of alternator by EMF method. 11. Measurement of 3 phase power by two wattmeter method 12. Wiring circuits for A. B. C. Calling bell Stair case Fluorescent lamp
16 REGULATIONS 2010
SATHYABAMA UNIVERSITY
SMTX1009
L 3
T 1
P 0
Credits 4
10 hrs.
Transforms of simple functions properties of transforms Transforms of derivatives and Integrals Periodic functions Inverse transforms Convolution theorems Initial and final value theorems
10 hrs.
Application of Laplace Transforms for solving : linear ordinary differential equations simultaneous differential equations integral equations.
10 hrs.
Analytic functions Cauchy Riemann equations in Cartesian and Polar form properties of analytic functions construction of analytic functions conformal mapping standard types bilinear transformations.
10 hrs.
Cauchys integral theorem integral formula Taylors and Laurents series (without proof) Residues Cauchys residue theorem Contour integration and the circle and semi circular contours.
10 hrs.
Test of Hypothesis Large sample test of significance single proportion - difference of proportions Single mean - difference of means. Small sample students t test single mean difference of means Fishers test difference of variance, Exact sample Chi square test goodness of fit independence of attributes.
SATHYABAMA UNIVERSITY
SCSX1014
L 3
T 0
P 0
Credits 3
10 hrs.
Object oriented fundamentals, Structured verses Object oriented development, elements of object oriented programming, fundamentals of OOP class, object, and abstraction and its importance, encapsulation, polymorphism, benefits of OOP, structure of C++ program.
10 hrs.
Working with classes classes and objects class specification, class objects, accessing class members, defining member functions, inline functions, accessing member functions within class, data hiding, class member accessibility, empty classes, constructors, parameterized constructors, constructor overloading, copy constructors, new, delete operators, this pointer, friend classes and friend functions.
10 hrs.
Function overloading, operator overloading, overload able operators, unary operator overloading, operator keyword, limitations of increment/ decrement operators, binary operator overloading, arithmetic operators, function templates, class templates.
UNIT IV INHERITANCE
10 hrs.
Base class and derived class relationship, derived class declaration, forms of inheritance, inheritance and member accessibility, constructors in derived class, destructors in derived class, multiple inheritance, multi level inheritance, hybrid inheritance, virtual base classes, virtual functions.
10 hrs.
Files and streams, opening and closing of files, file modes, file pointers and manipulation, sequential access to a file, binary file, random access to a file, error handling during file manipulation, exception handling, exception handling model, exception handling constructs, list of exceptions, catching exceptions, handling exceptions.
REFERENCE BOOKS:
1. Venu Gopal.K.R, Ravishankar.T, and Raj kumar, Mastering C++, Tata McGraw Hill, 1997. 2. Balaguruswamy.E, Object Oriented Programming with C++, Tata McGraw Hill, 2nd Edition, 2004. 3. Bjarne Stroustrup, The C++ programming language, Addison Wesley, 3rd Edition, 1998. 4. John R Hubbard, Programming with C++, Shaums Outline Series, McGraw Hill, 2nd Edition 5. James Martin & James J.Odell, Object Oriented methods A foundation Prentice Hall, 1997 6. Grady Booch, Object Oriented Analysis and Design with application, Addision Wesley, 2nd Edition, 1994
SATHYABAMA UNIVERSITY
SEEX1005
CIRCUIT THEORY
(Common to EEE, ECE, E&C, EIE & ETCE)
L 3
T 1
P 0
Credits 4
12 hrs.
Superposition Theorem - Reciprocity Theorem - Thevenins Theorem - Nortons Theorem - Maximum Power Transfer Theorem.
UNIT II TRANSIENTS
input.
9 hrs.
Time Domain Analysis - Transient response of RL, RC & RLC networks with DC input and AC with sinusoidal
12 hrs.
Coupled circuits - coefficient of coupling - Analysis of coupled circuits - single tuned and double tuned circuits (qualitative treatment only), Resonance circuits - Resonance in series and parallel circuits - Q factor, Bandwidth of resonant circuits
9 hrs.
Network Topology - Basic concepts of Graph theory, Network Graph, Tree, Incidence & Reduced Incidence Matrices, Cut sets, Tie sets, Cut set schedule, Tie set schedule - Application to network solutions - Duality and Dual Networks.
8 hrs.
Pspice - Introduction - DC Analysis and unit identification - AC and DC network Analysis - Circuit with variable resistor - Transient analysis.
TEXT BOOK:
1. Sudhakar & Shyammohan S Palli, "Electrical Circuits and Networks Analysis and Synthesis", Tata McGraw Hill, 3rd Edition, 2009
REFERENCE BOOKS:
1. 2. 3. 4. S.Sivanagaraju, G.Kishor & C.Srinivasa Rao, "Electrical Circuit Analysis", Cengage Learning, 1st Edition, 2010. W.H.Hayt, J.E.Kemmerly & S.M.Durbin, "Engineering Circuit Analysis", Tata McGraw Hill, 6th Edition, 2006. Soni Gupta, "Electrical Circuit Analysis", Dhanpat Rai publications, 6th Edition, 1997 (Reprint 2007) M.Arumugam & N.Premkumaran, "Electric Circuit Theroy", Khanna Publications, 4th Edition, 1989 (Reprint 2008).
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SMEX1013
L 3
T 0
P 0
Credits 3
10 hrs.
Concept of Stress and Strain-Normal and Shear Stresses-Simple and Compound stresses-Principal Stresses and Principal Planes-Normal, Shear and Volumetric strains-Relation between Elastic constants-Elasticity and Elastic Moduli-Poissons ratio.
10 hrs.
Concept of Shear force and Bending Moment-Beams and Support, Bending Moment and Shear Force Diagrams (Limited to simply supported, Cantilever Beams with Point Load and uniformly distributed load) Torsion of Circular Shafts-Torsion theory-Strength of the Shaft-Power transmitted by the Shaft-Closed and Open coiled Helical spring-Stress, Deflection, Strain Energy.
10 hrs.
Fluid Density-Specific weight-Specific gravity-Capillarity-Viscosity-Newtons Law-Surface Tension-Fluid Pressure and its Measurement. Types of Flow-Eulers and Bernoullis Equations - Venturimeters - Orifice meters - Notches and Weirs.
UNIT IV PUMPS
Centrifugal Pumps-Operation-Velocity Triangles-Performance Curves-Cavitation-Multistaging. Reciprocating Pumps-Operating Principles-Slip-Indicator Diagram-Separation-Air Vessels.
10 hrs.
UNIT V TURBINES
Introduction and Classification of Turbines-Working Turbine-Velocity Triangles-Cavitation-Draft Tube. Principles-Pelton Wheel-Francis
10 hrs.
Turbine-Kaplan
TEXT BOOKS:
1. Dr.Bansal.R.K-Strength of Materials, 4th Edition, Lakshmi Publications, 2007 2. Dr.Modi P.N, Dr.Seth S.M.-Hydraulics & Fluid Mechanics,17th Edition, Standard Book House, New Delhi, 2009 3. Dr.Bansal.R.K-A Text Book of Fluid Mechanics and Hydraulic Machines, 9th Edition, Laxmi Publications, 2009
60 ma
SATHYABAMA UNIVERSITY
SICX1004
L 3
T 0
P 0
Credits 3
UNIT I SENSORS
10 hrs
Difference between Sensors and Transducers Sensors for Motion and Position Measurement , GPS, INS, Doppler, SONAR. Thermal Sensors Gas Thermometric Sensors, Acoustic Temperature Sensor, Thermoemf Sensors, NQR Thermometry, Heat Flux Sensor. Biosensors Types - Calorimetric Biosensors, Potentiometric Biosensors, Amperometric Biosensors, Optical Biosensors, Immunosensors
UNIT II MEASUREMENTS
9 hrs.
Functional Elements of measurement system- Examples - Characteristics of instruments: Static characteristics Dynamic characteristics - Types of errors -sources of errors- methods of elimination-Analysis of data - Limiting errors-Relative limiting error-Combination of Quantities with limiting errors Statistical treatment of data: Histogram, Mean, Measure of dispersion from the mean, Range, Deviation, Average deviation, Standard Deviation, Variance.
10 hrs.
Transducers Classification of Transducers, Characteristics - Basic Requirements of a Transducer - Mechanical Devices as Primary Detectors -Mechanical Springs, Proving Rings, Potentiometer, Strain Gauges -Theory, Types (includes Rossette), Temperature Compensation, Calibration Resistance Hygrometer, Photoconductive cell, Hot wire anemometer.
11 hrs.
Self inductive transducers, Mutual inductive transducer, Linear variable Differential transformer - Eddy current gauge, Proximity sensors, Microsyn, Induction potentiometer, Capacitive displacement transducers, Single ended capacitive displacement transducers - Desirable features of capacitive transducers -Practical capacitive pickups - Equibar differential pressure transducer -Feedback type capacitance proximity pickup Capacitor microphone - Application in level measurement
10 hrs.
Piezoelectric, Photovoltaic, Hall Effect, Magnetostrictive, Radio-Active Absorption, Ionic Conduction Transducers, Digital Transducers - Digital Displacement Transducer, Shaft Angle Encoder, Optical Encoders, Magnetic Encoders -Digital Speed Transducers -Variable Reluctance Type, Smart Sensors - SQUID Sensors - Film Sensors MEMS., Sensors for angular measurement using non contact type ( wireless)
TEXT BOOKS:
1. Sawhney A.K., Electrical & Electronic Measurements and Instrumentation, Dhanpat Rai Publications,2001 2. D. Patranabis, Sensors and Transducers, Prentice Hall of India, 1999. 3. Doeblin E..O. Measurement System Applications and Design, TMH, 5 th Edition, 2004.
REFERENCE BOOKS:
1. Rangan C.S. Mani V.S.V: and Sharma G.R., Instrumentation Devices and Systems Tata McGraw Hill. 2. D. Patranabis, Principles of Industrial Instrumentation,TMH, 2nd Edition. 3. Dr. S. Renganathan, Transducer Engineering -Allied Publishers Limited.D.V.S Murthy Transducer and Instrumentation, PHI, 1st Edition
SATHYABAMA UNIVERSITY
SECX1002
DIGITAL SYSTEMS
(Common to ECE, ETCE, EEE, EIE, E&C & Bio-Med)
L 3
T 0
P 0
Credits 3
10 hrs.
Introduction to Number Systems Positional Number Systems, Number System conversion, Binary codes Binary arithmetic, Binary logic functions Switching algebra Functionally complete operation sets, Reduction of switching equations using Boolean algebra, Realization of switching function.
10 hrs.
Minimal two level networks Minimization of POS and SOP Design of two level gate networks Two level NAND-NAND and NOR-NOR networks Karnaugh maps Advantages and Limitations Quine McCluskys method.
10 hrs.
Adders Subtractors Binary parallel adders, Parallel subtractors, Parallel adder/subtractors, Binary decoders and encoders Priority encoders Multiplexers MUX as universal combinational modules Demultiplexers ALU module and comparator modules.
10 hrs.
Flip flops SR, JK, D and T flip flops, Master Slave flip flops, Characteristic and excitation table Shift registers Counters Synchronous and Asynchronous counters Modulus counters, Up/Down counters State diagram, State table, State minimization, Implication chart method.
10 hrs.
Classification and characteristics of logic family Bipolar logic family Saturated logic family RTL, DTL, DCTL, I2L,TTL, HTL Non saturated family Schottky TTL, ECL Unipolar family MOS, CMOS Comparison of logic families memories RAM, ROM, PROM, EPROM, EEPROM, SRAM, DRAM, CCD PAL, PLA HCT/HC series ICs.
TEXT BOOKS:
1. Morris Mano, Digital design, 3rd Edition, Prentice Hall of India, 2008.
REFERENCE BOOKS:
1. 2. 3. 4. Milos Ercegovac, Jomas Lang, Introduction to Digital Systems, Wiley publications, 1998. John M. Yarbrough, Digital logic: Applications and Design, Thomas Vikas Publishing House, 2002. R.P.Jain, Modern digital Electronics,3rd Edition, TMH, 2003. William H. Gothmann, Digital Electronics, Prentice Hall, 2001.
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SECX1012
ELECTRONIC CIRCUITS - I
(Common to ECE, E&C, EIE & ETCE)
L 3
T 0
P 0
Credits 3
10 hrs.
Half Wave Rectifier - Full Wave Rectifier Bridge Rectifier Performance of Rectifiers Filters Types of Filters L, C, LC, Filters Ripple Factor Calculation for C, L, LC and Filter Regulators Shunt and Series Voltage Regulator IC Regulator SMPS Power Control using SCR.
10 hrs.
Biasing Circuit Of BJT, Dc Equivalent Circuit Of BJT, DC And AC Load Lines, Stability Factor Analysis, Types of Amplifiers Equivalent Circuits Input-Output Characteristics Small Signal Equivalent Circuit of Amplifier Calculation of Gain, Input and Output Impedance of various Amplifiers using h-Parameter.
10 hrs.
Small signal model of JFET and MOSFET source bias circuit for FET voltage divider bias conversion of biasing circuits into CS, CG and CD amplifiers analysis of the different biasing using small signal model MOSFET biasing.
10 hrs.
Class A, B, C, AB and D type of operation efficiency of class A amplifier with resistive and transformer coupled load, efficiency class B, complementary symmetry amplifiers distortion in power amplifiers Thermal stability of power amplifier.
10 hrs.
Low frequency equivalent circuit and Miller effect response of BJT and JFET amplifiers High frequency response of BJT and JFET amplifier - Multi stage amplifier - Direct coupled amplifier RC coupled amplifier transformer coupled amplifier Cascode amplifier cascade amplifier Darlington emitter follower Bootstrap amplifier.
TEXT BOOKS
1. Jacob Millman and C. Halkias, Electronic Devices and Circuits, McGraw Hill, 2008. 2. Mithal. G.K., Electronic Devices and Circuits, Khanna Publishers, 23rd Edition, 2004.
REFERENCE BOOKS
1. 2. 3. 4. 5. Donald. L, Schilling and C.Belove, Electronic Circuits - Discrete and Integrated, 3rd Edition, McGraw Hill, 1989. David A. Bell, Electronic Devices and Circuits, PHI, 1998. Gupta. J.B, Electronic Devices and Circuits, Katson Publishers, 2009. Salivahanan. S, Electronic Devices and Circuits, TMH, 2008. Srinivasan. K.S, Electronic Circuits-I, 1st Edition, Anuradha Agencies.
SATHYABAMA UNIVERSITY
SECX4020
L 0
T 0
P 4
Credits 2
1. Verification of Thevenins Theorem. 2. Verification of Superposition Theorem. 3. Verification of Reciprocity Theorem. 4. Verification of Compensation Theorem. 5. Verification of Maximum Power Transfer Theorem.
DIGITAL CIRCUITS.
1. Verification of Truth Table In Basic & Universal Logic Gates. 2. Verification of Truth Table of Flip Flops- RS, D, JK, T. 3. Testing of Half Adder & Full Adder. 4. Testing of Multiplexer And Demultiplexer. 5. Testing of Decoder and Encoder. 6. Testing of Shift Registers.
L 0 T 0 P 4 Credits 2 Total Marks 100
SECX4021
ELECTRONIC CIRCUITS
1. 2. 3. 4. 5. 6. Analysis of Transistor Biasing Circuits Design and Testing of Full Wave Rectifier Circuit without and with filter. Characteristics of Shunt & Series Regulator. Design and Testing of RC coupled transistor amplifier Design and Testing of Emitter follower Design and Testing of Push pull power amplifier
24
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SMTX1010
ENGINEERING MATHEMATICS IV
(Common to All Branches except Bio Informatics)
L 3
T 1
P 0
Credits 4
10 hrs.
Formulation of equations by elimination of arbitrary constants and arbitrary functions-solutions by equations-general, particular and complete integrals-Lagranges linear equation-standard type of first order equation-second and higher order equations with constant coefficients-homogenous equations.
10 hrs.
Eulers formula-Dirichlets conditions-convergence statement only-change of interval-odd and even functions-half range series-RMS value-Parsevals formula-complex form of Fourier series-harmonic analysis.
10 hrs.
One dimensional wave equation-Transverse vibration of finite elastic string with fixed ends-boundary and initial value problems-Fourier series solution-Derivation of one dimensional heat equation-steady and unsteady state-boundary and initial value problems-Fourier series solutions. Two dimensional heat equation-steady state heat flow in two dimensions-Laplace equation in Cartesian coordinates - Fourier series solution.
10 hrs.
The infinite Fourier transform-sine and cosine transform-Properties-Inversion theorem-Finite Fourier transform-sine and cosine transform-Convolution theorem-Parsevals identity.
10 hrs.
Z Transforms Elementary Properties Inverse Z transforms Convolution theorem Formation of difference equations Solution of difference equations using Z transforms.
SATHYABAMA UNIVERSITY
SECX1013
ELECTRONIC CIRCUITS - II
(Common to E&C, ECE, ETCE & EIE)
L 3
T 0
P 0
Credits 3
10 hrs.
Types of feedback effect of feedback amplifier on noise, distortion gain, input and output impedance of the amplification, analysis of voltage and current feedback amplifier.
UNIT II OSCILLATORS
10 hrs.
Barkhausen Criterion for Oscillation in Feedback Oscillator Sinusoidal Oscillator Phase Shift Oscillator RC and Wein Bridge Oscillator Analysis of LC Oscillator, Colpitts, Hartley, Clap, Crystal Oscillator.
10 hrs.
Resonance Circuits, Unloaded and Loaded Q of Tank Circuit Bandwidth Types of Tuned Amplifiers Analysis of Single Tuned Amplifier Double Tuned Amplifier-Stagger Tuned Amplifier Instability of Tuned Amplifier Stabilization Techniques, Neutralization and Unilaterlization Class C Tuned Amplifiers and their Application.
10 hrs.
High Pass and Low Pass RC Circuits and their Response for Sine, Step, Pulse, Square, Ramp and Exponential Input Multivibrators Astable Multivibrators Emitter and Collector Coupled - Monostable, Bistable Multivibrators, and Schmitt Trigger Circuits.
10 hrs.
Principle of Time Based Generator Voltage Time Based Generator Bootstrapped and Miller Saw Tooth Generator Current time Based Generator Monostable and Astable Blocking Oscillator using Emitter Based Timing Push-Pull Operation of Blocking Oscillator
TEXT BOOKS
1. Millman. J And Taub. H, Pulse, Digital and Switching Waveforms, TMH, 2000. 2. Mithal G.K, Electronic Devices and Circuits, Khanna Publishers, 23rd Edition, 2004.
REFERENCE BOOKS
1. David A. Bell, Solid State Pulse Circuits, PHI, 2002 2. Venkatraman. R, Pulse, Digital Circuits and Computer Fundamentals. 3. Jacob Millman and C. Halkias, Integrated Electronics, Analog and Digital Circuits and Systems, McGraw Hill, 1997.
SATHYABAMA UNIVERSITY
SMEX1011
APPLIED THERMODYNAMICS
(Common to EEE, EIE & E&C )
L 3
T 0
P 0
Credits 3
10 hrs.
Basic concepts, Thermodynamic system-property, state, process, cycle, First law of thermodynamics and its application to non flow and steady flow processes, Second law of thermodynamics, Reversibility, Carnot theorem, Heat engine, Entropy.
10 hrs.
Steam generation,steam properties-dryness fraction, Use of steam tables and Mollier chart, Simple Rankine cycle, steam turbine - impulse and reaction, compounding. Flow of steam through nozzles, shapes of nozzles, effect of friction in nozzles, Critical pressure ratio.
10 hrs.
Air standard cycles - air standard efficiency - Otto and Diesel cycles, Combustion in petrol and diesel engines, Testing of internal combustion engines, Performance curves, determination of frictional horse power efficiencies, Heat balance calculations.
10 hrs.
Positive displacement compressor - reciprocating air compressor, work done, volumetric efficiency, Effect of clearance volume, multistaging, rotary compressors - vane type, roots blower-centrifugal compressor.
10 hrs.
Heat transfer-Modes of heat transfer- Heat transfer by conduction, convection and radiation - empirical relations, Laws of radiation, Vapour compression, refrigeration cycle, Calculation of coefficient of performance.
TEXT BOOKS:
1. Nag P.K, Engineering thermodynamics, 4th Edition, Tata McGraw Hill, 2008 2. Rajput R.K Thermal Engineering, 8th Edition, Lakshmi publications Ltd. New Delhi,2010
REFERENCES:
1. 2. 3. 4. Rogers and Mayhew, Engineering Thermodynamics, 4th Edition, Addison Wesley 1999. Manohar Prasad, Refrigeration and air conditioning, 2nd Edition, New Age International (P) Ltd, 2003. Domkundwar S, Arora S.C, A course in heat and mass transfer, Dhanpat Rai & Sons,2005 Ganesan.V.,Internal combustion Engines, 3rd Edition, Tata McGraw Hill, 2007
SATHYABAMA UNIVERSITY
SECX1004
L 3
T 0
P 0
Credits 3
10 hrs.
Continuous time signals (CT signals) and Discrete time signals (DT signals) Step, Ramp, Pulse, Impulse, Exponential Classification of CT and DT signals Periodic, aperiodic and Random signals Real and Complex signals Energy and power signals.
10 hrs.
Continuous time Fourier Transform and Laplace Transform analysis with examples Basic properties Parsevals relation Convolution in time and frequency domain Relation between Fourier transform and Laplace transform.
10 hrs.
CT systems Linear Time invariant Systems Basic properties of continuous time systems Linearity, Causality, Time invariance, Stability Frequency response of LTI systems Analysis and characterization of LTI systems using Laplace transform Computation of impulse response and transfer function using Laplace transform Differential equation Impulse response Convolution integral and Frequency response.
10 hrs.
Spectrum of D.T signals, Discrete Time Fourier Transform (DTFT), Discrete Fourier Transform (DFT) Basic principles of z-transform z-transform definition Region of convergence Properties of ROC Properties of z-transform Poles and Zeros Inverse z-transform using Contour integration Residue Theorem, Power Series expansion and Partial fraction expansion.
10 hrs.
LTI-DT systems Characterization using difference equation Properties of convolution and interconnection of LTI Systems Causality and Stability of LTI Systems Impulse response, Convolution Sum and Frequency response Computation of Impulse response and Transfer function using Z Transform.
TEXT BOOKS:
1. Allan V. Oppenheim et al, Signals and Systems, 2nd Edition., Prentice Hall of India Pvt. Ltd., 1997. 2. P.Ramesh Babu et al, Signals and Systems, 4th Edition, Scitech publishers, 2010. 3. Haykin. S and Van Been. B., Signals and Systems, 2nd Edition, John Wiley & Sons.2003.
REFERENCE BOOKS:
1. 2. 3. 4. 5. 6. Rao.P, Signals and Systems, 1st Edition, Tata McGraw Hill, 2008. Lathi, B. P., Linear Systems and Signals, 2nd Edition, Oxford University Press 2006 Mrinal Mandal, Amir Asif, Continuous and Discrete Time Signals and Systems, 1st Edition, Cambridge University Press 2007. Roberts, M.J., Fundamentals of Signals and Systems, 1st Edition, Tata McGraw Hill, 2007 S. Salivahanan et al., Digital Signal Processing, 2nd Edition, Tata McGraw Hill, 2009. H P Hsu, Signals and Systems,2nd Edition, Tata McGraw Hill, 2008.
SATHYABAMA UNIVERSITY
SICX1002
L 3
T 0
P 0
Credits 3
10 hrs.
Units of voltage and current -principle of operation, Constructional details, comparison of the following; DArsonval Galvanometer, permanent magnet moving coil, permanent magnet moving iron, Dynamometer, Induction, thermal and rectifier type instruments. Extension of ranges and calibration of voltmeter and ammeters -Errors and compensation.
10 hrs.
Power measurement; Voltmeter-ammeter method, three ammeters and three-voltmeter method. Types of Wattmeter-Dynamometer type, Induction type, Hall effect type, Thermal type, Compensated type, Single phase and 3-phase power measurement, Uses of instrument transformer with Wattmeter, Error and Compensation -Calibration of Wattmeter.
13 hrs.
Principle & Construction of energy meters -Single and polyphase induction type energy meter, D.C.energy meter -Energy meter testing -Calibration of Energy meter, KV/A meter, KV/AR meters, Maximum demand meter, Power factor meter, Synchroscope. Instrument transformers and special instruments: Potential Transformers and current transformers -Theory, Classification, Accuracy regarding ratio and phase angles.
8 hrs.
Ammeter- Voltmeter method and substitution method for resistance measurement. Wheat stone bridge, Kelvin double bridge, Wein Bridge, Hays bridge, Maxwell bridge, Anderson bridge, Schering bridge -Phasor diagrams for AC bridges -Sources and detectors in bridges -megger, Q-meter, Measurement of incremental inductance and Mutual inductance.
9 hrs.
DC Potentiometer: Laboratory type, Leeds and Northup potentiometer, Vernier potentiometer, Brookes deflection potentiometer -Working principle and applications. AC potentiometer: Drysdale potentiometer, Gall potentiometerWorking principle and applications, Application of DC and AC potentiometer - Magnetic measurement: Flux meter -Testing of Ring specimen, B-H curve by method of reversal and step by step method, Testing of Bar specimen. Hopkinsons permeameter- Iron loss measurement by Lloyd Fisher Square.
TEXT BOOK:
1. A.K.Sawhney, Electrical, Electronic Measurement & Instrumentation, Dhanpat Rai & sons,18th Edition, Reprint 2010.
REFERENCE BOOKS:
1. E.W. Golding and F.C. Widdis, Electrical Measurements and Measuring Instruments,5th Edition, Wheeler Publications. 2. M.B.Stout, Basic Electrical Measurements, PHI, 1981. 3. F.K.Harris, Electrical Measurements, Wiley Eastern Pvt.Ltd., 1974
SATHYABAMA UNIVERSITY
SECX1005
L 3
T 0
P 0
Credits 3
10 hrs.
Network functions Driving point impedance Transfer functions Poles and zeros, Significance of poles and zeros Determination of network function of one port and two port network Network parameters Z,Y, h and ABCD Conditions for reciprocity Parameter conversion.
10 hrs.
Image parameters Iterative parameter Image and iterative parameters in terms of open circuit and short circuit network Parameters of important Networks Lattice network T network Network Twin network Network Conversions Bartletts bisection theorem and its application Interconnection of Two Port Networks.
10 hrs.
Hurwitz polynomial Routh Criterion Positive Real function Elementary Synthesis Procedure Properties of LC, RC, and RL Driving Point Functions Synthesis of LC, RC, RL and RLC Network using Foster and Cauer forms Constant resistance network Synthesis of transfer admittance and transfer impedance with a one ohm termination.
UNIT IV FILTERS
10 hrs.
Filters Constant K Low Pass Filter High Pass Filter Band Pass Filter Band Stop Filter m Derived Filters Terminating Half Section Composite Filter Design of First order, Second order Low Pass, High Pass, Butterworth and Chebyshev filters.
10 hrs.
Attenuators Symmetrical and Asymmetrical T and Attenuator Design of Attenuators Equalizer Types Series and Shunt Equalizer Constant Resistance Equalizer Types of simple four terminal Equalizers Full Series Equalizer, Full Shunt Equalizer, Bridged T Equalizer and Lattice Equalizer Characteristics of equalizers.
TEXT BOOKS:
1. Sudhakar and Shyam Mohan Palli, Circuits and Networks; Analysis and Synthesis, 3rd Edition, Tata McGraw Hill, 2008. 2. John.D.Ryder, Networks Lines and Fields, 2nd Edition, PHI Publications, 2003.
REFERENCE BOOKS:
1. Kuo, Network Analysis and Synthesis, 2nd Edition, PHI, 1995. 2. Soni and Gupta,Electric Circuits and Analysis, 5th Edition, Dhanpatrai and Sons, 1995. 3. Umesh Sinha, Network Analysis and Synthesis, 5th Edition, Sathya Prakashan Publishers, 1985
SATHYABAMA UNIVERSITY
SMEX4005
L 0
T 0
P 4
Credits 2
L 0
T 0
P 4
Credits 2
List of experiments:
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Design Design Design Design Design Design Design Design Design Design and and and and and and and and and and Testing Testing Testing Testing Testing Testing Testing Testing Testing Testing of of of of of of of of of of Hartley Oscillator. RC Phase Shift Oscillator. Colpitts Oscillator. Astable Multivibrator. Schmitt Trigger. Tuned Amplifier. Monostable Multivibrator Using PSPICE Simulation. Bistable Multivibrator Using PSPICE Simulation. Feedback Amplifier Using PSPICE Simulation. Wein Bridge Oscillator Using PSPICE Simulation.
31
REGULATIONS 2010
SATHYABAMA UNIVERSITY
L 3
T 1
P 0
Credits 4
10 hrs.
Curve Fitting-Method of group averages-Principle of least squares-Method of moments-Finite Differences-Operators E & D-Relationship between operators.
UNIT II INTERPOLATION
10 hrs.
Interpolation-Newtons method-Lagranges method-Numerical Differentiation and Integration-Trapezoidal and Simpsons Rule-Finite Difference Equations.
10 hrs.
Numerical solution of Algebraic and Transcendental Equations-Regula Falsi method-Newton Raphson method-Graffes Root Squaring method-Simultaneous linear algebraic equations- Gauss Jordan method-Crouts method-Gauss Seidel method-Relaxation method.
10 hrs.
Numerical solution of Ordinary Differential Equations-Taylors series-Modified Eulers method-Runge Kutta method of fourth order-Predictor-Corrector methods-Milnes method-Adams Bashforth method.
10 hrs.
Numerical solution to Partial Differential Equations-Classification-Elliptic equations-Poissons equations-Leibmanns iteration procedure-Parabolic equation-Bender Schmidt Scheme-Crank Nicholsons Scheme-Hyperbolic equations.
SATHYABAMA UNIVERSITY
SECX1028
L 3
T 0
P 0
Credits 3
10 hrs.
Review of Time domain and Frequency domain representation of DTLTI system Discrete random signals Averages Auto correlation and power spectral density DFT Properties Linear and Circular convolution FFT Decimation in time FFT and Decimation in frequency FFT algorithms Inverse DFT Applications of FFT to convolution.
10 hrs.
Review Butterworth and Chebyshev approximations Properties of IIR and FIR filters Design of IIR filter using Impulse invarient and Bilinear transformation method Design of FIR filter using window method rectangular, Hanning hamming, Kaiser windows.
10 hrs.
Realization structure for FIR & IIR filters Direct Form I and Direct Form II, cascade, parallel realization Effect of number representation in registers fixed point arithmetic floating point arithmetic Errors due to rounding ADC quantization noise coefficient quantization error product quantization error truncation limit cycles due to product round off error addition of over flow errors Scaling dynamic range.
10 hrs.
Introduction- Concepts of Multirate Signal Processing- Decimation by integer factor- interpolation by integer factor -Sampling rate conversion by non integer factor multistage approach to sampling rate conversion Application: echo cancellor, efficient digital to analog Conversion in compact hi-fi systems.
10 hrs.
TMS320C5416 family Architecture Addressing mode Instruction set- Simple programs Introduction to code composer studio software Simulation.
TEXT BOOKS:
1. John G Proakis and Dimtris G Manolakis, Digital Signal Processing, 3rd edition,PHI Pearson Education, 2000. 2. P.Ramesh Babu et al., Digital Signal Processing,4th edition, Scitech Publishers, Reprint 2010.
REFERENCE BOOKS:
1. 2. 3. 4. 5. 6. Sanjit K.Mitra, Digital signal Processing A Computer Based Approach, 3rd Edition, Mc Graw Hill,2006. J.G.Prokias, Digital Signal Processing, 2nd Edition, Prentice Hall, 1996. Rabiner and Gold, Theory and application of Digital Signal Processing, Prentice Hall, 2007. Oppenheim and Schafer, Digital Time Signal Processing, 2nd Edition, Prentice Hall, 1999. Ashok Ambarder, Digital Signal Processing., 1st Edition, Cengage learning, 2006. Venkataramani, Digital Signal Processors, Tata Mc Graw Hill, 14th Reprint of 2008.
Exam Duration : 20 60 60
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SECX1010
L 3
T 0
P 0
Credits 3
8 hrs.
Fabrication of ICs, Packaging of ICs, Realizations of Passive & Active Devices Like R, C, Diodes, Transistors in ICs, IC Technology- Monolithic, Thin Film and Hybrid Technologies, Fabrication Constraints, Design Guidelines. OpAmps- Internal Circuit and Block Diagram -DC and AC Characteristics of OpAmps
11 hrs.
Applications of Opamp- Arithmetic Circuits, Amplifiers, Opamp Circuits Using Diodes, Rectifiers, V to I and I to V Converters, Clipper and Clamper Sample and Hold Circuit. Comparators Characteristics and its Applications.
10 hrs.
Schmitt Trigger, Monostable, Astable Multivibrators, Saw tooth, Triangular and Sine Wave Generators.
9 hrs.
First Order - Second Order
12 hrs.
Basic Principles - Phase Detector and Comparator: Analog and Digital - Voltage Controlled Oscillator - Low Pass Filter- Monolithic Phase Locked Loop Applications of PLL: Frequency Multiplication/ Division - Frequency Translation - AM Detection - FM Detection FSK Demodulation - 555 Timer Functional Diagram - Monostable Operation - Astable Operation - Their Applications Schmitt Trigger Counters, Timers.
TEXT BOOKS:
1. D.Roy Choudhry, Shail B. Jain, Linear Integrated Circuits 3rd Edition, New Age International Pvt. Ltd., 1998 2. William D.Stanely, Operational Amplifiers with Linear Integrated Circuits. Pearson Education, 4th Edition,2004.
REFERENCES:
1. K.R.Botkar, Integrated Circuits. Khanna Publishers, 9th Edition, 1996. 2. James M.Fiore, Operational Amplifiers & Linear Integrated Circuits: Theory & Applications, Delmer Thomas Learning, 2001. 3. Ramakant A.Gayakwad, OP-AMP and Linear Integrated Circuits, 4th Edition, PHI Publisher, 2000.
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SICX1013
L 3
T 0
P 0
Credits 3
10 hrs.
Introduction to Industrial & chemical processes, unit operations-Transport of liquids, solids and gases- Adjusting of particle size of bulk solids- Mixing processes- Separation processes.
10 hrs.
Qualitative study of unit operations with an understanding of operating variables; Distillation, chemical reactors, steam boilers.
10 hrs.
Qualitative study of unit operations with an understanding of Operating variables, Dryers, Crystallization, Evaporators.
10 hrs.
Qualitative study of unit operations with an understanding of operating variables. Furnaces, Centrifuges, Heat exchangers.
10 hrs.
Qualitative study of Unit operations with an understanding of operating variables. Pumps, Compressors, Extruders.
SATHYABAMA UNIVERSITY
SICX1005
L 3
T 0
P 0
Credits 3
10 hrs.
Review of DC and AC Voltmeters - Electronic Multimeter-Q-Meter-True RMS Voltmeter- Differential Voltmeter-Vector Impedance Meter-Vector Voltmeter-RF Voltage and Power Measurements.
10 hrs.
Function Generators-RF Signal Generators-Sweep Generators-Frequency Synthesizer-Wave Analyzer-Harmonic Distortion Analyzer -Spectrum Analyzer, Noise Generator, Pattern Generator, Wobbuloscope.
10 hrs.
Basic Oscilloscope-CRT- Vertical Deflection System- Horizontal Deflection System-CRO Probes-Applications of CRO-Special Purpose Oscilloscope-Sampling Oscilloscope-Storage Oscilloscope-Digital Storage Oscilloscope.
8 hrs.
Digital Voltmeter -Digital Multimeter-Frequency Counter-Measurements of Frequency and Time Interval- Extension of Frequency Range-Measurement Errors.
12 hrs.
X-Y Recorders-Magnetic Recorders, Strip Chart Recorders, Interference & Screening Multiple earth & earth loops electrostatic & Electromagnetic interference Grounding Techniques -Digital Recorders and Data Loggers-Analog and Digital Data Acquisition System- Interfacing of Transducers-Multiplexing-Computer Controlled Instrumentation-IEEE488 Electrical Interface.
TEXT BOOKS:
1. Alber.D.Helfrick & William.D.Cooper, Modern Electronic Instrumentation & Measurement Techniques, PHI, 2003. 2. Ernest. O. Doeblin, Measurement Systems Application and Design TMH, 5th Edition, 2004.
REFERENCE BOOKS:
1. Joseph.J.Carr, Elements of Electronics Instrumentation & Measurement, Pearson Education, 2003. 2. Alan S.Morris, Principles of Measurements &Instrumentation, PHI, 2nd Edition, 2003.
SATHYABAMA UNIVERSITY
SICX1008
INDUSTRIAL INSTRUMENTATION
(Common to EIE & E&C)
L 3
T 0
P 0
Credits 3
10 hrs.
Measurement of speed- Revolution counter, Dragcup tachometer, AC and DC tachogenerators, photo electric pickup. Measurement of force - Load cell, pneumatic load cell, hydraulic load cell. Measurement of Torque using strain gauges and magneto elastic principle, Measurement of acceleration - Elementary accelerometers, seismic accelerometers, practical accelerometers, calibration.
10 hrs.
Manometers different types of manometers, Elastic pressure transducers, Dead weight Tester, Electrical types, Vacuum gauges - McLeod gauge, Knudsen gauge, thermocouple gauge, ionization gauge, Differential pressure transmitter - electrical & pneumatic types
10 hrs.
Temperature scales, Bimetallic thermometer, filled- in Thermometers, Vapour pressure thermometers, Resistance thermometers, Thermistors, Thermostat, Thermocouples - types and ranges, characteristics, laws of thermocouples, cold junction compensation, IC temperature sensors AD 590, Pyrometers - radiation and optical pyrometers.
10 hrs.
Orifice, Venturi, Pitot tube, flow nozzle rotameter, Positive displacement meter, turbine flowmeter, electromagnetic flow meter, ultrasonic flow meter, open channel flow measurement, solid flow measurement. Sight glass, float gauge, displacer, torque tube, bubbler tube, diaphragm box, Differential Pressure methods, electrical methods- resistance type, capacitance type, ultrasonic level gauging
10 hrs.
Hydrometer continuous weight measurement, liquid densitometer float principle, air pressure balanced method, using gamma rays gas density measurements gas specific gravity measurements Viscosity terms, saybolt viscometer, rotometer type viscometer, Industrial consistency meters. Humidity terms dry & wet bulb psychrometers hot wire electrode type hygrometer, electrolytic hygrometer, Dew point hygrometer
TEXT BOOKS:
1. D. Patranabis, Principles of Industrial Instrumentation, Tata McGraw Hill, 2ndEdition, New Delhi, Reprint 2009. 2. S. K. Singh, Industrial Instrumentation & Control 3rd Edition, Tata McGraw Hill, Reprint 2009. 3. K.Krishnaswamy & S.Vijayachitra, Industrial Instrumentation New age International, Reprint 2008.
REFERENCE BOOKS:
1. Ernest O. Doeblin, Dhanish. N. Manik, Measurement Systems Application & Design, TMH, 5th Edition, 2004. 2. R.K.Jain, Mechanical & Industrial Measurements, Khanna Publishers, 11th Edition, 2004.
SATHYABAMA UNIVERSITY
SEEX1010
CONTROL SYSTEMS
(Common to EEE, ECE, ETCE, E&C & EIE)
L 3
T 1
P 0
Credits 4
12 hrs.
Types of system open loop systems, closed loop systems, Basic elements in control system Mathematical models of physical system: Differential equation- transfer functions of simple electrical networks, Electrical analogous of mechanical translational and Rotational system D.C and A.C servomotor Mechanical system- Translational and Rotational system Block diagram reduction techniques Signal flow graphs.
10 hrs.
Standard test signals -Time response of first and second order system, Time domain- specifications- Generalized error series Steady state error and error constants.
10 hrs.
Characteristics equation Location of roots in S plane for stability Routh Hurtwitz criterion Root locus construction Nyquist stability criterion.
10 hrs.
Frequency response of the system Correlation between time and frequency response Gain and Phase margin Bode plot.
8 hrs.
Introduction to compensation networks Lag, Lead and Lag Lead networks Compensator Design P, PI, PID Controllers design using Bode plot. Total No of Hours: 50 hrs.
TEXT BOOKS:
1. Ashok Kumar, Control Systems, TMH Ltd, Ist Edition, 2006. 2. Kausuhio Ogata, Modern Control Engineering, Prentice Hall of India Pvt. Ltd., 3rd Edition, 1998. 3. Smarajit Ghosh, Control System Theory & applications, 2nd Edition, Pearson Education, Publishers, 2005
REFERENCE BOOKS:
1. 2. 3. 4. 5. I.J.Nagrath and M.Gopal, Control Systems Engineering, New Age International (P) Limited, Publishers, 2nd Edition, 2009 M.N. Bandyo Pathyaj, Control Engineering, Theory and Practice, PHI, 1st Edition, 2005. N.K Sinha, Control Systems, New Age International(p) Limited, Publishers, 3rd Edition, 1998 Roy Choudhury, Modern Control Engineering, Prentice Hall of India, 2nd Edition, 2005 Richard Dorf, Modern Control Systems, Pearson Education Ltd, 8th Edition. 2005
38
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SECX4027
L 0
T 0
P 4
Credits 2
SECX4002
L 0
T 0
P 4
Credits 2
Measurement of Medium Resistance Using Wheat stones Bridge Measurement of Low Resistance Using Kelvins Double Bridge Measurement of Capacitance Using Scherings Bridge Measurement of Inductance Using Andersons Bridge Calibration of Ammeter, Voltmeter Design of Current to voltage & Voltage to current converters Displacement versus output characteristics of potentiometer transducer Strain Gauge characteristics Load cell characteristics Characteristics of LVDT Characteristics of Thermocouple Characteristics of Thermistors Step response characteristics of RTD Hall Effect transducers
39
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SICX1006
L 3
T 1
P 0
Credits 4
10 hrs.
Review of matrices-co-ordinate transformation- Eigen values and Eigen vectors- diagonalization Cayley Hamilton theorem- state transition matrix.
10 hrs.
State space analysis state space formulation- state space representation of control systems described by scalar differential equation state variable- transformation of state space equation , physical ,phase & canonical variable, state space models-state space representation for discrete time system.
10 hrs.
Jordan and canonical forms, controllability and observability condition for controllability and observability, Gilbert method and Kalman decomposition- design of state feedback by pole placement.
10 hrs.
Controllable phase variable form, observable phase variable form, reduced order observer full order observer-reducibility, irreducibility, transfer function matrix, impulse response functions.
10 hrs.
Non linear systems properties of non linear system describing function for simple non linearitys like ON-OFF, dead zone and saturation- describing function analysis of non linear systems phase plane method basis concept- singular points constructing phase plane trajectory for linear and nonlinear second order systems.
SATHYABAMA UNIVERSITY
SECX1015
L 3
T 0
P 0
Credits 3
UNIT I MICROPROCESSORS
10 hrs.
Microprocessors evolution and types, general 8 bit microprocessors and its architecture-8085,Z80,6800-8086 microprocessors family overview,8086 internal architecture,introduction to programming of 8086
10 hrs.
Instruction cycle timing diagram-machine cycle-instruction format-addressing modes-instruction set of 8085-assembler directives-stack &subroutines-assembly language programs
10 hrs.
Microprocessors and microcontrollers-microcontroller evolution-8051 architecture input/output ports, program and data memory, counters and timers, serial data I/O, interrupts-introduction set and assembly language programs
10 hrs.
Data transfer schemes-programmable I/O-serial I/O-peripheral ICS-8251,8255,8259,8279-DMA, interfacing-7 segment LED & LCD Display- stepper motor water level control-ADC & DAC-applications
10 hrs
TEXT/REFFERENCE BOOKS:
1. 2. 3. 4. 5. Gaonkar, Microprocessors Architecture, Programming, And Application With 8085, Wiley Eastern Publication.,1997. Kenneth J. Ayala, The 8051 Microcontroller:Architecture, Programming And Applications, Penram International Publishings, 1996. Dougals .V.Hall, Microprocessors &Interfacing-Programming and Hardware, Tata McGraw Hill, 1991. Walter A.Trebel & Avtar Singh, The 8088 and 8086 Microprocessors, PHI, 1985. Barry B. Brey, The Intel Microprocessor 8086 8088 80186 80286 80386 80486 Pentium And Pentium Pro Processor Architecture, Programming And Interfacing, PHI, 7th Edition (March 23, 2005). 6. Mazidi & Mazidi, The 8051 Microcontroller And Embedded System, PHI, 2000.
SATHYABAMA UNIVERSITY
SICX1007
PROCESS CONTROL
(Common to E&C & EIE)
L 3
T 0
P 0
Credits 3
10 hrs.
Process variable load variables-dynamic of simple pressure, flow, level and temperature process-transient response of first order system for thermal & level process interacting & non-interacting system degrees of freedom batch process and continuous process self regulator servo and regulator operation.
10 hrs.
Characteristics of On-Off, Proportional, Integral, Derivative modes P + I, P + D And P + I + D control modes pneumatic and electronics controller quantitative analysis
10 hrs.
decay ratio, IAE, ISE, ITAE determination of optimum setting for mathematically described process by using time response and frequency response tuning of controller by process reaction curve method, continuous cycling method, feed forward control, cascade control, ratio control, split -range control and multivariable control introduction to adaptive control and inferential control
10 hrs.
I/P and P/I Converter pneumatic, electric and hydraulic actuator valve positioner control valves characteristics of control valve valve body globe, butterfly valves control valves sizing cavitation, flashing in control valves
10 hrs.
Piping and instrumentation diagram of loops, interaction of control loops, non interacting control loops, relative gain array control of distillation column control of heat exchanger.
TEXT BOOKS:
1. Stephanopoulos.C, Chemical Process Control, Prentice Hall of India Pvt Ltd, 2004 2. Eckman D.P, Automatic Process Control, Wiley Eastern Ltd, 1972. 3. Curtis D Johnson, Process Control Instrumentation Technology , John Wilsey & Sons, 2004.
REFFERENCE BOOKS:
1. 2. 3. 4. 5. P.Harriot, Process Control , Tata McGraw Hill , 1984. B.G.Liptak, Instrumentation in Process Industries , Vol. 1 & 2, Chilton Book&Co. 1974. D.R.Coughanowr, Process System Analysis and Control, 2nd Edition, John Wiley & Sons, 1991. F.G.Shinskey, Process Control System, 3rd Edition, McGraw Hill, 1991. B.G.Liptak, Process Control, Chilton Book & Co, 2001
SATHYABAMA UNIVERSITY
SECX1048
L 3
T 0
P 0
Credits 3
8 hrs.
Introduction to Fuzzy Set Theory Basic Concepts of Fuzzy Sets - Classical Set Vs Fuzzy Set Properties of Fuzzy Set Fuzzy Logic Operation on Fuzzy Sets Fuzzy Logic Control Principles Fuzzy Relations Fuzzy Rules Defuzzification.
10 hrs.
Fuzzy Logic Controller Fuzzification Interface Knowledge Base Decision Making Logic Defuzzification Interface Application of Fuzzy Logic to Water Level Controller - Temperature Controller- Inverted Pendulum Control Control of Blood Pressure during Anaesthesia.
10 hrs.
Fundamentals of ANN Biological Neurons and Their Artificial Models Types of ANN Properties Different Learning Rules Types of Activation Functions Training of ANN Perceptron Model (Both Single & Multi Layer) Training Algorithm Problems Solving Using Learning Rules and Algorithms Linear Separability Limitation and Its Over Comings
12 hrs.
Back Propagation Training Algorithm Practical Difficulties Counter Propagation Network Structure & Operation Training of Kohonen and Grossberg Layer Applications of BPN & CPN - Statistical Method Training Application Boltzman Training Cauchy Training Hop Field Network and Boltzman Machine Speed Energy Function Network Capacity Applications A / D Converter Travelling Sales Man Problem RBF Network
10 hrs.
BAM Structure Types Encoding and Retrieving Adaptive Resonance Theory Architecture of ART 1 & ART 2 Implementation Training Characteristics Introduction to Optical Neural Network Cognitron & Neocognitron
TEXT BOOKS:
1. Timothy Ross, Fuzzy Logic with Engineering Application, McGraw Hill, Edition 1997. 2. James A. Freeman & Skapura, Neural Networks, Pearson Education, 2007.
REFERENCE BOOKS:
1. B.Yegnanarayana, Artificial Neural Networks Prentice Hall, September 2007. 2. Simon Haykin, Artificial Neural Networks, 2nd Edition, Pearson Education. 3. Drainkov, H.Hallendoor and M.Reinfrank, An Introduction to Fuzzy Control, Edition 2001.
SATHYABAMA UNIVERSITY
L 0
T 0
P 4
Credits 2
List of experiments
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11 12 13 Familiarization of 8085 trainer kit, 8086 trainer kit,8051 trainer kit & 89C51 C. Addition & subtraction of 8 and 16 bits using 8085. Multiplication & division 8 and 16 bits using 8085 Interfacing of stepper motor using 8085. Interfacing of traffic light using 8085. Addition and subtraction of two 16 bit numbers using 8086. Code converters using 8086. Sorting of N numbers using 8086. Arithmetic operation programs using 8051. Interfacing of ADC using 8051. Interfacing of DAC using 8051. Addition and subtraction using 89C51. Filling of internal memory using 89C51.
SICX4003
L 0
T 0
P 4
Credits 2
1. 2.
Characteristics of I/P & DPT converter Characteristics of valve (a) based on position (b) Shape of valve body
Study and control of a level process using ON-OFF, P, PI, PD, PID controllers. Study and control of a Pressure process using ON-OFF, P, PI, PD, PID controllers. Study and control of a flow process using ON-OFF, P, PI, PD, PID controllers. Study and control of a Temperature process using ON-OFF, P, PI, PD, PID controllers. Verification of logic gates using PLC Study of DCS Cascade control Study of Ratio control Interacting and non- interacting system Tuning of controller using Zeigler Nicholas method
44 REGULATIONS 2010
SATHYABAMA UNIVERSITY
SBAX1001
L 3
T 0
P 0
Credits 3
10 hrs.
Management Definition Basic Function Contribution of Taylor & Fayol. Types of structure Line, staff, Functional, Committee, Project & Matrix Structures. Departmentalization Centralization Decentralization span of control. Management By Objectives Management By Exception.
10 hrs.
Forms of Business / Industrial Ownership Sole Trader, Partnership, Company, Performance Appraisal Basic Principles Pitfalls Methods to Overcome. Industrial Safety Causes of Accidents Cost of Accident How to minimize Accidents. Plant Layout & Maintenance Need, Types & Managerial Aspects.
10 hrs.
OB Definition Nature & Scope Contributing Disciplines Importance of OB to Managers. Personality Definition Theories Factors Influencing Personality. Motivation Definition Theories. Theory X & Y Transactional Analysis. Morale & Job Satisfaction Factors Influencing Job Satisfaction.
10 hrs.
Group Definition Types Determinants of Group Cohesiveness Communication Process Barriers Effective Communication. Leadership Theories Factors Contributing to Effective Leadership Role of Trade Union in Organizations Functions of Trade Union Why Trade Union is required? Types of Trade Union.
10 hrs.
Ethics in Workplace Formulation of Ethics Managerial Ethics Managing Ethical Behaviour Codes of Ethics Encouraging Ethical Behaviour Social Responsibility Spirituality.
SATHYABAMA UNIVERSITY
SICX1010
L 3
T 0
P 0
Credits 3
10 hrs.
Need for computer in a control system- functional block diagram of a control system- direct digital controlsupervisory control-scheduling control- digital control interfacing: process inputs, outputs interface-data loggers-data acquisition system- type of displays, computer various input/outputs- computer control action- treatment of inputs, outputs, and control strategies.
10 hrs.
Mathematical representation of sampling process- Z transform & properties- inverse Z transform-pulse transfer function-data hold sampling frequency consideration-open loop& closed loop response of sampled data control systemmodified Z transform- stability of sampled data control system- stability in Z domain- Schur-Cohn stability test, bilinear transformation, Jurys test of stability.
10 hrs.
Control algorithm- design of control algorithm using Z transform-dead beat algorithm - Dahlins method-ringing Kalmans approach-PID algorithm position & velocity form- tuning the algorithm- selection of sampling time.
10 hrs.
PLC- configuration- ladder diagrams- relay based PLC- computer based PLC- typical control features- interlocks & alarms.
10 hrs.
DCS-different architectures - functional elements- remote electronic unit- redundancy- different methods of communication protocol network.
TEXT BOOKS:
1. Deshpande P.B. & Ash R.H, Elements of Computer Process Control, Instrument Society of America 1981. 2. Michal.P Lucas, Distributed Control System , Van Nostrand Reinhold & Co 1986. 3. Frank D.Petruzella, Programmable Logic Controllers, 3rd Edition 2005.
REFFERENCE BOOKS:
1. 2. 3. 4. Liptak B.G, Instrumentation in Process Industries, Vol.I &II Chilton Book Co, 1974 George Stephanopoulos.C, Chemical Process Control, PHI, 2005 Curtis D Johnson, Process Control Instrumentation Technology, John Wiley & Sons, 2006. John.W.Webb, Programmable Logic Controllers-Principle & Application, PHI 2007.
SATHYABAMA UNIVERSITY
SICX1009
BIOMEDICAL INSTRUMENTATION
(Common to EIE, E&C, ECE, ETCE & EEE)
L 3
T 0
P 0
Credits 3
10 hrs.
Cell and Its Structure Electrical, Mechanical and Chemical Activities Action and Resting Potential- Organization of Nervous System CNS PNS Neurons Axons- Synapse Propagation of Electrical Impulses along the NerveSodium Pump Cardio Pulmonary System- Physiology of Heart, Lung, Kidney.
11 hrs.
Design of Medical Instruments Components of Biomedical Instrument System Electrodes: Micro Electrodes, Needle Electrodes, Surface Electrodes Transducers Piezo Electric, Ultrasonic, Passive Transducers Resistive, Capacitive, Inductive Biomedical Measurements Like PH, PCO2, PO2 of Blood, Isolation Amplifier, Preamplifier, Current Amplifier, Chopper Amplifier.
9 hrs.
ECG, Einthoven Triangle, Leads, Electrodes, Vector Cardiograph, Measurement of Cardiac Output, EEG, EMG, Plethysmography, Blood Flow Measurements, Holter Monitor- Respiratory Rate Measurement Oximeter, Patient Monitoring System, ICCU.
10 hrs.
Ultrasonic Diagnosis, Ultrasonic Scanning, Isotopes in Medical Diagnosis- Pace Makers, Defibrillators, Doppler Monitor(colour), Medical imaging-X-ray generation, Radiographic & Fluoroscopic Techniques Image Intensifiers-Computer Aided Tomography, PET, SPECTLaser Applications-Echocardiography-CT Scan-MRI/NMR-Endoscopy.
10 hrs.
Dialysers Surgical Diathermy Electro Anaesthetic and Surgical Techniques. Sources of Electric Hazards and Safety Techniques. Single Channel Telemetry, Multi channel Telemetry, Implantable Telemetry, Wireless Telemetry, Telemedicine, Telemedicine Applications.
TEXT BOOKS:
1. Khandpur, Handbook of Biomedical Instrumentation 2nd Edition, Tata McGraw Hill, 2003. 2. M.Arumugam, Biomedical Instrumentation, Anuradha Publications, Reprint 2009.
REFERENCE BOOKS:
1. 2. 3. 4. Leslie Cromwell, Fred J. Werbell and Eruch A. Pfeigger, Biomedical Instrumentation and Measurements 2nd Edition W.J.Tompkins and J.G. Webster, "Design of Microcomputer Based Medical Instrumentation", Prentice Hall, 1991 L.A. Geddes and L.E. Baker, "Principle of Applied Biomedical Instrumentation" 3rd Edition, Wiley, 1989 D.W. Hill, "Principle of Electronics for Medical Research", 2nd Edition, Butterworths, 1965.
SATHYABAMA UNIVERSITY
SECX1064
L 3
T 0
P 0
Credits 3
10 hrs.
Definition, Design and need for Data Acquisition Systems -D/A Converters-Implementing a DAC Function-Use of Ladder Networks-Bipolar Coded DACs -A/D Converters-Parallel A/D, Feedback A/D, Ramp type A/D, Dual slope A/D, Successive Approximation A/D-Comparison of A/D Conversion Techniques- Microprocessor/PC based Data Acquisition Systems
10 hrs.
Principles of Internet Working-Repeaters, Hubs, Bridges, Switches, Routers, Gateways-Internet ProtocolEncoding-Types of Encoding-Frequency and time-division Multiplexing techniques
8 hrs.
Modulation- Need for Modulation- AM-Frequency Spectrum- Power Relation Different types of Modulators- SSB and VSB Generation-AM Transmitters- Block Diagram- Functions of each block High level and Low Level Transmitters.
10 hrs.
Angle Modulation-Principle of Frequency and Phase Modulation-Relation between FM and PM Waves- Band width of FM-Narrow Band And Wide Band FM Wave- Generation of FM wave- Direct and Indirect Methods FM Transmitters-Block Diagram- Functions of each block
12 hrs.
Detection and Receivers Detection of AM Waves-Diode Detectors-Synchronous Detectors-FM Detectors-Phase Discriminators-Ratio Detectors. Receivers-Different types-Superheterodyne receivers-Block Diagram-Choice of IF and Oscillator Frequencies- Tracking-Alignment-AVC,AFC, Receiver Characteristics.
TEXT BOOKS:
1. G.B.Kennedy, Electronic Communication Systems, 4th Edition, Tata McGraw Hill, 1993. 2. Anokh Singh, Principles of Communication Engineering S.Chand & CO. 3. A.S.Tanenbaum, Computer Networks ,3rd Edition, Prentice Hall of India, 1996
REFERENCE BOOKS:
1. 2. 3. 4. 5. 6. G.B.Clayton, Data Converters, The Macmillan Press Ltd., 1982 Roddy D.Coolen.J, Electronic Communications, 4th Edition, PHI, 2007. Taub and Schlling, Principles of communication systems, Tata McGraw Hill, New Delhi, 1995. Behrouz A Forouzan, "Data Communication and Networking". Simon Haykin, Communication System, John Wiley & Sons, 4th Edition, 2001 Bruce Carlson et al., Communication Systems, Tata McGraw Hill, 4th Edition, 2002.
SATHYABAMA UNIVERSITY
SECX1021
L 3
T 0
P 0
Credits 3
10 hrs.
The MOS transistor-Current Voltage Relations-Threshold Voltage-Second order effects-MOS models-Design of Logic gates-Stick diagrams DC characteristics Small signal AC characteristics of CMOS inverter Dynamic behavior Power consumption Scaling of MOS circuits.
10 hrs.
Static CMOS design Determination of Pull-up and Pull-down ratio-Sizing of transistors Ratioed logic-Pass transistor logic Dynamic CMOS design Noise consideration Domino logic, np CMOS logic Power consumption in CMOS gates Multiplexers Transmission gates design.
10 hrs.
Introduction Static sequential circuits- CMOS static flip-flop Dynamic sequential circuits Pseudo static latch - Dynamic two phase flip-flop clocked CMOS logic C2 MOS latch- Pipelining NORA CMOS logic True single phase clocked logic Realization of DFF in TSPC logic.
10 hrs.
Introduction-Designing Static and Dynamic Adder circuits The Array Multiplier Multiplier structuresBaugh-Wooly Booth Multiplier Barrel shifter Memory structures SRAM and DRAM design Design approach of Programmable logic devices PLA, PAL and FPGA.
10 hrs.
Digital system design process Language elements of VHDL- Operators-Data Types Signal assignments Concurrent and Sequential assignments-Process statement Wait statement If statement - Loop statement - Assertion statement Data flow modeling - Structural modeling Behavioral Modeling- Examples Total Hours: 50
TEXT BOOKS
1. Jan M.Rabaey, Digital Integrated Circuits, 2nd Edition, September 2000, PHl Ltd. 2. M.J.S.Smith, Application Specific Integrated Circuits, Ist Edition 1997, Pearson Education.
REFERENCE BOOKS
1. 2. 3. 4. 5. Douglas A.Pucknell, Basic VLSI design, PHI Limited 1998. E.Fabricious, Introduction to VLSI design, Mc Graw Hill Limited 1990. Neil Weste, Principles of CMOS VLSI design, Addison Wesley 1998. Wayne Wolf, Modern VLSI design, 2nd Edition 2003, Pearson Education. Sung-Mo Kang & Yusuf CMOS Digital Integrated Circuits- Analysis & Design, 2nd Edition, MGH.
SATHYABAMA UNIVERSITY
SICX1014
L 3
T 1
P 0
Credits 4
10 hrs.
Definition- overview of PLC systems - Input/ Output modules - Power supplies IO slots. General PLC programming procedures - programming on-off outputs. Auxiliary commands and functions - creating ladder diagrams from process control descriptions. PLC basic programming digital logic Gates-boolean algebra. Basic PLC functions-register basics - timer functions - counter functions.
12 hrs.
Arithmetic functions - number comparison functions - skip and MCR functions - data move systems. PLC Advanced intermediate functions- utilizing digital bits - sequencer functions - PLC Advanced functions: alternate-programming languages - operation. PLC-PID functions -PLC installation - trouble shooting and maintenance - controlling a robot - processes with PLC - design of inter locks and alarms using PLC.
UNIT III INTERFACE AND BACKPLANE BUS STANDARDS FOR INSTRUMENTATION SYSTEMS
6 hrs.
Field bus: Introduction - concept - international field bus standards. HART protocol: method of operation - structure - operating conditions and applications.
10 hrs.
Evolution of DCS - building blocks different architectures-comparison of architectures-detailed descriptions and functions of local control units basic elements & functions-operator stations - data highways - redundancy concepts.
12 hrs.
DCS communication Facilities-communication system requirements-architectural issues-protocol issues-communication system standards-operator interfaces-low level and high level operator interfaces-Engineering interfaces- low level and high level Engineering interfaces
TEXT BOOKS:
1. John Webb, W, Ronald Reis, A.,: Programmable Logic Controllers Principles and Applications, 3rd Edition, Prentice hall Inc., New Jersey, 1995. 2. Krishna Kant, Computer based Industrial Control, Prentice Hall India. 1997. 3. Lucas, M.P.,: Distributed Control Systems, Van Nostrand Reinhold Co., New York, 2nd Edition, 1986
REFERENCE BOOKS:
1. Petruzella., Programmable Logic Controllers 3rd Edition, Tata McGraw Hill, Newyork. 2. Hughes, T. Programmable Logic Controllers, ISA Press 1994. 4th Edition. 3. Mckloni, D.T. Real Time Control Networks, ISA Press 1994.
SATHYABAMA UNIVERSITY
SICX1015
ANALYTICAL INSTRUMENTATION
(Common to EIE & E&C)
L 3
T 0
P 0
Credits 3
5 hrs.
Sampling systems ion selective electrodes conductivity meters pH meters - dissolved oxygen analyser sodium analyser silica analyser moisture measurement.
9 hrs.
Oxygen analyser CO monitor NOx analyser H2S analyser dust and smoke measurement- thermal conductivity type thermal analyser industrial analysers.
10 hrs.
Gas chromatography liquid chromatography principles, types and applications high-pressure liquid chromatography detectors.
13 hrs.
Spectral methods of analysis Beers law UV visible spectrophotometers single beam and double beam instruments source and detectors IR spectrophotometers sources and detectors FTIR spectrometers atomic absorption spectrophotometer flame emission spectrophotometers sources of flame photometry applications.
13 hrs.
NMR basic principle NMR spectrometers applications introduction to mass spectrophotometers nuclear radiation detectors GM counter proportional counter solid state detectors introduction to x-ray spectroscopy.
SATHYABAMA UNIVERSITY
SICX4004
L 0
T 0
P 4
Credits 2
Level measurement using d/p transmitter Flow measurement using Orifice and Venturi meter Calibration of Thermocouple 4. Calibration of Pressure transmitter Torque measurement 6. Viscosity measurement UV-Visible Spectrophotometer 8. IR Spectrophotometer Vacuum Pressure measurement Conductivity meter calibration and measurements of conductivity of test solutions. pH meter standardization and measurement of pH values of test solutions Radiation Pyrometer & IR Thermometer
SICX4005
L 0
T 0
P 4
Credits 2
USING MATLAB
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Design of digital controller using dead beat algorithm. Design of digital controller using Dahlins algorithm Design of digital controller using Kalmans algorithm Implementation of Logic gates Design of Half adder and Full adder Building of VI to demonstrate conversion of Centigrade to Fahrenheit and create a subroutine for conversion of Centigrade to Fahrenheit Building of VI to demonstrate software timings while loop and waveform chart. Building VI for analysing and logging of data Building of VI to demonstrate Multi-plot graph using waveform charts Building of VI to demonstrate error clusters and handling. Building of VI to stimulate simple test sequence using simple state machine architecture. Building of VI to design Multimeter.
USING VHDL
S18XPROJ
L 0
T 0
P 30
Credits 15
The objective of the project work is to make use of the knowledge gained by the student at various stages of the degree course. Students, will also be permitted to undertake industrial/consultancy project Work, outside the department, in industries/Research labs. There shall be three assessments during the semester by a review committee. The student shall make three presentations on the progress made before the committee at various stages of the Project work. The Head of the Department shall constitute the review committee for each branch of study. The total marks obtained in the three reviews, shall be taken in to account. There will be a viva-voce examination at the end of the Project work, conducted by one internal examiner and one external examiner. The total marks secured will be the sum of marks secured in the Project reviews and Viva Voce Examination. Each student is required to submit a Project report on the project assigned to him by the department. The report should be based on the information available in the literature or data obtained by the student by way of experiments conducted in the laboratory/industry.
B.E. (ELECTRONICS & INSTRUMENTATION) 52 REGULATIONS 2010
SATHYABAMA UNIVERSITY
SICX1012
L 3
T 0
P 0
Credits 3
10 hrs.
Introduction- function description-data types-tool boxes- graphical display-import and export of data-programs for solution of state equation-controller design-limitation-simple control application programs.
10 hrs.
Numerical solution- Rungekutta method - Adam bass worth technique- solution of ordinary differential equationsimulation of first order, second order and lead-lag transfer function- Matlab routine for step and impulse response development of dynamic model and Laplace domain model using MATLAB
10 hrs.
Introduction-graphical user interface- starting - selection of objects- blocks-lines- simulation-application programs-limitations- FIS editor- study of fuzzy logic tool box-GUI editor-rule view-membership function editor- rule editor.
10 hrs.
Introduction to virtual instrumentation-VIs and sub VIs, loops and charts, arrays, cluster and graphs, case and sequence structure, formula nodes, local and global variables, string and file I/O.
10 hrs.
DIO, RS232/RS485, GPIB,USB & PCMCIA VISA and IVI-networking basics for office & industrial applications Fourier transform, power spectrum, correlation methods, windowing and filtering, VI applications in instrumentation and control, robotics, networking and communication, image acquisition and processing.
SATHYABAMA UNIVERSITY
SICX1016
FUNDAMENTALS OF MECHATRONICS
(Common to EIE, E&C, ECE, EEE, ETCE & BIOMED)
L 3
T 0
P 0
Credits 3
UNIT I INTRODUCTION
10 hrs.
Mechatronics: Definition & Key Issues Evolution Elements Mechatronics Approach to Modern Engineering Design.
10 hrs.
Types Displacement, Position and Proximity & Velocity Sensors Signal Processing Data Display.
10 hrs.
Introduction to Mechanical Types and Electrical Types Pneumatic & Hydraulic Systems Applications Selection of Actuators
10 hrs.
Types of Controllers Microprocessor Applications in Mechatronics- 2 case studies in automobiles, and 2 case studies in robotics, Programming Interfacing Computer Applications
10 hrs.
Manufacturing Mechatronics Automobile Mechatronics -2 Case Studies Medical Mechatronics 2 Case Studies
TEXT BOOKS:
1. W.Bolton. N, Mechatronics: Electronic Control System for Mechanical & Electrical Engineering, 2nd Edition, Pearson Education, 2004. 2. Dr. K.P. Ramachandran, G.K. Vijaya Raghavan, Mechatronics, A.R.S. Publications, Second Edition, 2008.
REFERENCE BOOKS:
1. D.A. Bradly, D. Dawson, N.C.Burd and A.J. Loader, Mechatronics: Electronics in Products and Processes Nelson Publisher, 2004. 2. Michael B.Histand & David G.Alciators, Introduction to Mechatronics & Measurement systems, McGraw- Hill International Editions, 1998. 3. Dan Necsulescu, Mechatronics, Pearson Education, 2005.
SATHYABAMA UNIVERSITY
SICX1020
L 3
T 0
P 0
Credits 3
10 hrs.
Origin & various generation of Robots - Robot definition - Robotics system components Robot classification - Coordinate frames - Asimovs laws of robotics degree of freedom work volume - Need for Automation - types of automation fixed, programmable and flexible automation.
10 hrs.
Sensing - Range, proximity, position, velocity, acceleration, Touch, Force, Torque. Optical & laser sensors. Machine vision - Introduction, Image acquisition, Illumination Techniques, Image conversion, Cameras, Image processing and analysis image data reduction segmentation feature extraction Object recognition.
10 hrs.
Introduction - various types of grippers-design considerations. Construction of Manipulator Introduction to Robot Dynamics Lagrange formulation Newton Euler formulation Properties of robot dynamic equations.
10 hrs.
10 hrs.
Robot programming - Fixed instruction, sequence control, General programming language, Specific programming languages. Robots for welding, painting and assembly Remote Controlled robots Robots for nuclear, thermal and chemical plants.
TEXT BOOKS:
1. Mikell P. Groover, Weiss M. Nagel R.N. Odrey. N.G. , Industrial Robotics, Tata McGraw Hill, 3rd Reprint, Edition 2008. 2. Deb.S.R. Robotics Technology and Flexible Automation, Tata McGraw Hill, 9th Reprint 2004. 3. K.S Fu, R C.Gonzalez, CSG Lee- Robotics, McGraw Hill, Edition 2008.
REFERENCE BOOKS:
1. John J Craig Introduction to Robotics Mechanics & Control, Low price Edition, 7th Reprint, 2005. 2. Ghosh, Control in Robotics and Automation : Sensor Based Integration, Allied Publishers.
PART A : 2 Questions from each unit, each carrying 2 marks PART B : 2 Questions from each unit with internal choice, each carrying 12 marks
B.E. (ELECTRONICS & INSTRUMENTATION) 55
20 marks 60 marks
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SICX1025
SATELLITE INSTRUMENTATION
(Common to E&C & EIE)
L 3
T 0
P 0
Credits 3
10 hrs.
Satellite systems, orbital description, Orbital mechanics of LEO, MEO and GSO, Placement of a satellite in a GSO, Satellite description of different communication subsystems, Bandwidth allocation, Satellite subsystems, attitude and orbit control systems, TTC&M, communication subsystem, satellite antenna satellite link design: basic transmission theory, system noise temperature and G/T ratio, downlink design, uplink design, satellite systems using small earth station, design for specified C/N.
10 hrs.
Space craft configuration, payload and supporting subsystems, satellite uplink downlink power budget, C/No, G/T, Noise temperature, system noise, propagation actors, Rain and ice effects, Polarization calculations, Link design with and without frequency reuse.
10 hrs.
Attitude control of satellites, Reaction wheel, Momentum wheel, Thrusters, Stabilization satellites, Spin stabilization. Gravity gradient stabilization, yo-yo mechanism, control moment gyros, orbit determination of satellites, sensors in satellite ADCS. Dual spinners, navigation of satellites, ascent guidance, satellite rendezvous. Tethered satellite systems, satellite services, space stations, docking of spacecrafts.
10 hrs.
Advanced very high resolution radiometer, high-resolution infrared radiation sounder, Microwave sounding unit, stratospheric sounding unit, advanced microwave sounding unit, solar backscatter ultraviolet radiometer, GOES imager and sounder.
10 hrs.
INTELSAT series, INSAT, VSAT, Remote sensing, Mobile satellite, Service: GSM, GPS, INMARSAT, Satellite navigation system, Direct to home service (DTH), special services, E-mail, Video conferencing and internet connectivity
SATHYABAMA UNIVERSITY
SICX1026
ULTRASONIC INSTRUMENTATION
(Common to E&C & EIE)
L 3
T 0
P 0
Credits 3
10 hrs.
Ultrasonic waves: principle and propagation of various waves, characterization of ultrasonic transmission, reflection and transmission coefficients, intensity and attenuation of sounds beam .power level, medium parameters.
10 hrs.
Generation of ultrasonic waves: magnetostrictive and piezoelectric effects, search unit types, construction and characteristics
10 hrs.
Ultrasonic test methods: pulse echo, transit time, resonance, direct contact and immersion type and ultrasonic methods of flaw detection.
10 hrs.
Ultrasonic measurements: ultrasonic methods of measuring thickness, depth and flow, variables affecting ultrasonic testing in various applications.
10 hrs.
Ultrasonic applications: ultrasonic applications in medical diagnosis and therapy, acoustical holography.
SATHYABAMA UNIVERSITY
SICX1029
L 3
T 0
P 0
Credits 3
10 hrs.
Orifice meter design of orifice for given flow condition design of rotameter design of RTD measuring circuit design of cold junction compensation circuit for thermocouple using RTD Transmitters Zero and span adjustment in D/P transmitters and temperature transmitters.
10 hrs.
Bourdon gauges factors affecting sensitivity design of Bourdon tube Design of Air purge system for level measurement. Electronic P + I + D controllers design adjustment of set point, bias and controller settings.
10 hrs.
Control valves design of actuators and positioners types for valve bodies valve characteristics materials for body, and trim sizing of control valves selection of body, materials and characteristics of control valves for typical applications.
UNIT IV PUMPS
10 hrs.
Types of pumps pump performance pipe work calculation characteristics of different pumps pump operation maintenance instruments used in pumping practice pump noise and vibration selection of pumps.
10 hrs.
Design of logic circuits for alarm and annunciator circuits, interlocks design of microprocessor based P + I + D controller.
TEXT BOOKS:
1. N.A. Anderson, Instrumentation for Process Measurement and Control, Chillton Company, 1980, 3rd Edition, 1997, CRC Press 2. D.M. Considine, Process Instruments and Controls Handbook, McGraw Hill Book Co. 1985, McGraw Hill Professional, 5th Edition, 1999.
REFERENCES:
1. 2. 3. 4. R.H. Warring, Pumping Manual, Gulf Publishing Co., 1984. C.D. Johnson, Process Control Instrumentation Technology, Prentice Hall Inc.. 7th Edition, 2002. Terry Bartelt, Instrumentation and Process Control, Nov.28, 2006, Delmar Cengage Learning. Donald.P. Eckman, Automatic Process Control, Wiley Eastern Ltd., New Delhi, 1993.
SATHYABAMA UNIVERSITY
SICX1022
L 3
T 0
P 0
Credits 3
10 hrs.
Review of Sampled Data Control System Sample and Hold Operation Review of Z Transform- Pulse Transfer Function Z Domain Equivalents to S Domain
10 hrs.
Stability Analysis Correlation between Time Response and Root Location in the Z Plane Effect of Pole Zero Configuration in Z Plane Transient Response of Sampled Data Steady State Error
10 hrs.
Discrete Time State Equation State Diagram Realization of Pulse Transfer Function Direct Realization Cascade Realization Parallel Realization Sampled Data Model of Continuous Time System Concepts of Controllability and Observability Systems with Dead Time.
10 hrs.
Transform of Digital Control System Design Specification Design on the W Plane Digital PID Controller Introduction to Design on the Z Plane.
10 hrs.
Implementation of Control Algorithm using Microprocessor General Description of Micro Controller Digital Quantization Signal Quantization
TEXT BOOK:
1. Gopal. M, Digital Control Engineering, Willey Eastern Publishers,1998.
REFERENCE BOOKS:
1. Nagrath. I.J. Control System Engineering, New Age International, 2006. 2. Yoan D. Landau, Gianluca Zito, Digital Control System: design, identification and implementation, Springer, 2006.
SATHYABAMA UNIVERSITY
SICX1023
L 3
T 0
P 0
Credits 3
UNIT I INTRODUCTION
10 hrs.
Introduction to Adaptive Control Effects of Process Variations Adaptive Control Schemes Adaptive Control Problems Non Parametric Identification Classifications of Adaptive Control Systems
10 hrs.
Linear in Parameter Models ARX ARMAX ARIMAX Least Square Estimation Recursive Least Square Estimation Extended Least Square Estimation Maximum Likelihood Estimation Introduction to Nonlinear Systems Identification Pseudo Random Binary Sequence.
10 hrs.
Different Approaches to Self Tuning Implicit and Explicit STR LQG Self Tuning Introduction to Stochastic Self Tuning Regulators Stochastic Indirect Self Tuning Regulators
10 hrs.
Different Configurations and Classifications of MRAC Direct and Indirect MRAC MIT Rule for Continuous Time MRAC Systems Lyapunov Approach and Hyper Stability Approach for Continuous Time and Discrete Time MRAC Systems Relation Between MRAC and STR.
10 hrs.
Recent Trends in Self Tuning Design of Gain Scheduling Controller Auto Tuning of PID Regulator Stability Analysis of Adaptive Controllers Application of Adaptive Control in Chemical Reactor, Distillation Column, Variable Area Tank System
SATHYABAMA UNIVERSITY
SICX1017
L 3
T 0
P 0
Credits 3
12 hrs.
Introduction to petroleum exploring, processing and refining constituents of crude oil P& I diagram of petroleum refinery Instrumentation and control in distillation columns: distillation equipment- variable and degrees of freedom measurement and control of column pressure - liquid distillate -vapour distillate and inserts - control of feed, re-boiler and reflux - use of gas chromatograph-cascade and feed forward controls. Temperature control and pressure control in batch reactors.
10 hrs.
Control of batch dryers and continuous dryers.- Instrumentation and control in heat exchangers: variables and degree of freedom - liquid to liquid heat exchangers - steam heaters condensers -reboilers and vaporizers -use of cascade and feed forward control.
8 hrs.
10 hrs.
10 hrs.
Types Of Evaporators - Measurement And Control Of Absolute Pressure, Density, Conductivity, Differential Pressure And Flow In Evaporators- Intrinsic Safety Of Instruments
TEXT BOOKS:
1. Bela.G. Liptak - Instrumentation In The Processing Industries - Chilton Book Company, 1994. 2. R.F. Goldstien, A.L.Waddams, Petroleum Chemicals Industry, Spon-Publisher, 3 rd Edition,1967.
REFERENCE BOOKS:
1. 2. 3. 4. D.M. Considine and S.D.Ross - Handbook Of Applied Instrumentation -Mcgraw Hill, 1964. Curtis D.Johnson, Process Control Instrumentation Technology, 17th Edition, Pearson Education, New Delhi, 2002. George.T. Austin, Shreeves Chemical Process Industries, 5 th Edition, McGraw Hill, 1998. Balchan J.G and Mumme K.I, Process Control Structures and Applications, Van Nostrand Reinhold Company, New York, 1988.
SATHYABAMA UNIVERSITY
SICX1018
L 3
T 0
P 0
Credits 3
10 hrs.
Flow Diagram and description of the process raw materials - Pulping process Chemical recovery process Paper making process Converting.
10 hrs.
Special Process Parameters Measurements of basic weight Density - Specific gravity Flow level and solids - Pressure -Temperature - Consistency Moisture pH Oxidation Reduction potential Graphic displays and alarms.
10 hrs.
Typical Control Systems Blow tank controls Digester liquor feed pump controls Brown stock washer level control stock chest level control Basic weight control Dryer temperature control.
10 hrs.
Special Control applications Dissolving tank density control White liquor classifier density control White liquor flow control Condensate conductivity control.
10 hrs.
Computer Application Evolution of control Programmable logic Controllers Distributed Control Systems (DCS) Applications for paper machine Controls.
TEXT BOOKS:
1. LIPTAK B.G., Process Measurement And Analysis Third Edition, Chilton Book Co., 1995. 2. Douglas M..Considine, Process / Industrial Instruments & Controls Hand Book, Fourth Edition, McGrawhill, 1993.
REFERENCE BOOKS:
1. Hobart.H.Willard, Lyne.L..Meritt, John.A.Dean, Frank.A.Settle, Instrumental method of Analysis, Seventh Edition, CBS Publishers & Distributors, 1986.
SATHYABAMA UNIVERSITY
SICX1024
L 3
T 0
P 0
Credits 3
10 hrs.
Air data instruments: altimeter, air speed rate of climb gyroscopic instruments turn and back indicator artificial horizon directional Gyro Schuler Tuning, Stable Platform Introduction to Automatic pilots integrated flight instruments altitude compensation.
11 hrs.
Automatic direction finder distance measuring equipments -instruments landing system visual omni range radar optical instruments engine instruments and control pressure measurements thermal meter control tachometer accelerometer smoke and fire detection propeller controls twin blade control - cabin pressure and temperature.
8 hrs.
10 hrs.
Basic description of a flight simulator Solution of Aerodynamics equations simulation of abnormal conditions Jet engine power plant troubles Flight controls and auto pilot troubles. Simulation Simulation of difficult conditions Weapons system trainer Need for realism Instrumentation.
11 hrs.
Hydraulic systems troubles landing gear troubles cabin conditioning troubles indication of unsafe canopy Boeing condition Radio troubles Separate generator System troubles Trouble indicator light Advantages of instrumentated flight Black box and its use.
TEXT BOOKS:
1. Pallett E.G.H., "Aircraft Instrumentation and Integrated Systems", Longman Scientific and Technical, 1992. 2. Nagaraja N.S., "Elements of Electronic Navigation", Tata Mcgraw Hill Publishing Ltd., New Delhi, 1975.
REFERENCES BOOK:
1. Douglas M. Considine and S.D. Ross, Handbook of Applied Instrumentation, McGraw Hill, 1965.
SATHYABAMA UNIVERSITY
SICX1028
L 3
T 0
P 0
Credits 3
10 hrs.
Brief survey of methods of power generation Hydro, thermal, nuclear, solar wind and wave power Importance of instrumentation in power generation Thermal power plants Block diagram Details of boiler processes - P&I diagram of boiler Cogeneration.
10 hrs.
Non electrical parameters Flow of feed water, fuel, air and steam with correction factor for temperature and pressure Drum level measurement Radiation detector Smoke density measurement Dust monitor.
10 hrs.
10 hrs.
Combustion control Air/fuel ratio control Furnace draft control Drum level control Main steam and reheat steam temperature control Super heater control Air temperature Deaerator control Distributed control system in power plants Interlocks in boiler operation.
10 hrs.
Speed, vibration, shell temperature monitoring and control Steam pressure control Lubricant oil temperature control Cooling system.
TEXT BOOKS:
1. Sam G. Dukelow, The Control of Boilers, Instrument Society of America, 1991. 2. P.K. Nag, Power Plant Engineering, Tata McGraw Hill, 2001.
REFERENCE BOOKS:
1. S.M. Elonka and A.L. Kohal, Standard Boiler Operations, Tata McGraw Hill, New Delhi, 1994. 2. R.K.Jain, Mechanical and Industrial Measurements, Khanna Publishers, New Delhi, 1995. 3. E.Al. Wakil, Power Plant Engineering, Tata McGraw Hill, 1984.
SATHYABAMA UNIVERSITY
SECX1040
L 3
T 0
P 0
Credits 3
10 hrs.
Elements of Digital Image Processing Systems Elements of Visual Perception structure of human eye light, luminance, brightness and contrast, mech band effect image formation Monochrome vision model Image fidelity criteria Color vision model Introduction to 2D system linear, shift invarient, casual and stable systems optical and modulation transfer function 2D sampling theorem Aliasing reconstruction of image from samples Practical limitations in sampling and reconstruction Image quantization Lloyd max quantizer Optimum mean square uniform quantizer.
10 hrs.
Need for transform 2D Orthogonal and Unitary transform and its properties 1D & 2D DFT Properties separability,translation, periodicity, conjugate symmetry, rotation, scaling,convolution and correlation FFT Statement, proof and properties of Separable transforms Walsh, Hadamard, Haar, Discrete Sine, DCT, Slant, SVD & KL transforms .
10 hrs.
Spatial domain method point operation Histogram modelling Spatial operations directional smoothening, median filtering, image sharpening, masking, edge crispening, interpolation Transform operation linear filtering, root filtering Homomorphic filtering Degradation model diagonalization Constrained and Unconstrained restoration Inverse filtering Wiener filter generalised inverse, SVD and iterative methods.
10 hrs.
Spatial feature extraction Edge detection Boundary extraction and representation region and moment representation structure Texture Scene matching and detection Image segmentation Classification techniquesPattern recognisation Perceptron for two pattern classes Training algorithm Non seperable classes.
10 hrs.
Fundamentals of coding coding, inter pixel and psychovisual redundancy, fidelity criteria Image compression models fundamental coding theorem Shannons coding, Huffman coding Pixel coding Predictive techniques lossy and lose less predictive coding variable length coding Transform coding Zonal and thereshold coding Image compression standards CCITT and JPEG standards.
TEXT BOOKS:
1. Anil .K.Jain, Fundamentals of Digital Image Processing, 1st edition, PHI New Delhi, 1995., 2. Gonzalez R.C. and R.E.Woods, Digital Image Processing, 2nd edition, Pearson Education Ltd 2002.
REFERENCE BOOKS:
1. 2. 3. 4. William K Pratt, Digital Image Processing,,3rd edition, John Wiley & Sons, 2001. Greenberg A.D. and S.Greenberg, Digital Images: A Practical Guide, ,1st edition, McGraw Hill,1995. Nick Efford, Digital image Processing a practical introduction using JAVA, Pearson Education Ltd., 1st edition, 2000. Edward R Dougherty, Electronic Imaging Technology, 1st edition, PHI, 2005.
SATHYABAMA UNIVERSITY
SECX1041
PROGRAMMING IN MATLAB
(Common to ECE, ETCE, E&C, EEE & EIE)
L 3
T 0
P 0
Credits 3
10 hrs.
Defining Variables functions Matrices and Vectors Strings Input and Output statements -Script files Arrays in Mat lab Addressing Arrays Dynamic Array Cell Array Structure Array File input and output Opening & Closing Writing & Reading data from files.
10 hrs.
Relational and logical operators Control statements IF-END, IF-ELSE END, ELSEIF, SWITCH CASE FOR loop While loop Debugging Applications to Simulation miscellaneous MAT lab functions & Variables.
10 hrs.
Basic 2D plots modifying line styles markers and colors grids placing text on a plot Various / Special Mat Lab 2D plot types SEMILOGX SEMILOGY LOG- LOG POLAR COMET Example frequency response of filter circuits.
10 hrs.
Linear algebric equations elementary solution method matrix method for linear equation Cramers method Statistics, Histogram and probability normal distribution random number generation Interpolation Analytical solution to differential equations Numerical methods for differential equations.
10 hrs.
Simulink Simulink model for a dead zone system, nonlinear system Applications in DSP Computation of DFT & FFT Filter structure IIR & FIR filter design Applications in Communication PCM, DPCM, DM, DTMFInterfacing of Matlab with event driven simulators.
TEXT BOOK:
1. Rudra Pratap, "Getting Started with MATLAB 6.0", 1st edition, Oxford University Press, 2004.
REFERENCE BOOKS:
1. William J.Palm, "Introduction to MATLAB 6.0 for Engineers", Mc Graw Hill & Co 2. M.Herniter, "Programming in MATLAB", Thomson Learning. 3. John G.Proakis, "Digital Signal Processing using MATLAB", Thomson Learning.
SATHYABAMA UNIVERSITY
SECX1042
L 3
T 0
P 0
Credits 3
10 hrs.
Printed Circuit Boards(PCB)- Construction Types of PCB- Multilayer Surface Mount technology PCB Manufacturing process PCB Inspection methods Bare Board Testing Optical and X ray Inspection Electrical tests Text fixtures Bed of nails fixtures Cross talk test Mock up test In circuit test burn in test Fault diagnostic methods. Electromagnetic compatibility testing of electronic components, subassemblies, Measuring Instruments and systems
10 hrs.
Symptom Recognition Bracketing Technique Component failure Analysis Fault types and causes in circuits during manufacturing Manual trouble shooting technique Tools and Instruments DMM CRO PCO Logic probes Logic pulsar Logic Analyzer.
10 hrs.
ATE Techniques CPU Emulator technique ROM amd ROM Emulators In circuit Comparator In Circuit Functional test Trouble shooting digital gates Testing Linear Integrated Circuits Guarding Technique VI trace Technique Bus Cycle Signature System Board functional test methods Boundary scan test basics
10 hrs.
ATE System Components Digital Pin Electronics Drive data formats Digital High way Analog Highway Test Vector Generation Creating test patterns Fault Simulations.
10 hrs.
MDA test systems Boundary scan test with I/O pin compatibility Automatic optical inspection systems Combinational ATE Systems Design for testability Observability and Controllability Testing Flow diagram Stuck at fault model Fault simulation Ad Hoc technique Scan design technique Basics of ATPG BIST-Test pattern generation for built in self test - Exhaustive pattern generation and deterministic testing Output response Analysis Transition count syndrome checking Signature Analysis Circular BIST.
TEXT BOOKS:
1. Michael L.Bushnell et al., "Essentials of Electronic testing for digital, memory and mixed signal VLSI circuit", 1st edition, Academic Press, 2002. 2. Randall L Geiger, Pillip E Allen, "VLSI Design Techniques for Analog and Digital Circuits", MGH, 1990.
REFERENCE BOOKS:
1. Parag.K.lala, Digital circuit Testing and Testability, 1st Edition, Academic press, 2001. 2. Alfred L.Crouch, "Design for test for Digital ICs and Embedded core systems", 2nd edition, PHI, 1999. 3. Sabapathy S.R., Test Engineering for electronic hardware, Qmax publishers, 1st Edition, 2007.
SATHYABAMA UNIVERSITY
SECX1047
EMBEDDED SYSTEMS
(Common to E&C & EIE)
L 3
T 0
P 0
Credits 3
10 hrs.
Introduction to embedded systems hardware and software components types- examples- characteristics challenges in embedded computing system design embedded system design process.
10 hrs.
I/O devices examples synchronous Iso- synchronous and asynchronous communications from serial devices UART- RS232-RS485-USB- Power issues- FPGA-ASIC- diagnostic port.
10 hrs.
Interpreter compiler- assembler cross assembler simulators & emulators in-circuit emulators high level language description of s/w for embedded systems, java based embedded systems design.
10 hrs.
Introduction to real time theory operating systems OS services real time operating systems concepts real time kernel kernel services task scheduling interrupt processing clocking communication & synchronization control blocks, memory requirements and control basic design using RTOS
10 hrs.
Cell phones, smartcard, digital thermometer personal digital assistants set top boxes inkjet printers telephone PBX. introduction to micro C/OS-11 operating systems and Its uses.
TEXT BOOKS:
1. Raj Kamal, Embedded Systems- Architecture, Programming And Design, Tata Mcgraw Hill, 2003.
REFFERENCE BOOKS:
1. 2. 3. 4. Wayen Wolf, Computer As Components-Principles of Embedded Computing Systems Design, Harcourt India pvt Ltd., 2001. David E Simon, An Embedded Software Primer, Pearson education, 2004. Sriram V Iyer, Pankaj Gupta, Embedded real-time systems programming, Tata Mcgraw Hill, 2004. K.V.K.K. Prasad, Embedded/real-time system: concepts, design and programming, Dreamtech press, 2004.
SATHYABAMA UNIVERSITY
SECX1059
L 3
T 0
P 0
Credits 3
10 hrs.
Introduction to pattern recognition, types of images, regular pattern, irregular pattern, fuzzy methods. Statistical pattern recognition, feature selection, syntactic pattern recognition, clustering and non supervised learning methods.
10 hrs.
Combined detection method, edge detection, edge linking, gradient. Laplacian, line detection, method based, point detection, snake methods. Boundary description detection, matching, merges segmentation, smoothing, splitting of boundaries syntactic, analysis of region boundaries, study of shape by region analysis.
10 hrs.
Explanation of how fuzzy approach can be applied to pattern recognition, classificatory analysis preprocessing, feature detection and primitive extraction, adaptive classification of fuzzy grammar. Algorithms for pattern recognition, neural network fundamentals, approaches for pattern recognition.
10 hrs.
Introduction of Computer Vision, Computer Imaging System, Image Formation and sensing CVIP tools Software, Image representation. Area Extraction: Concepts, Data-structures, Edge, Line- Linking, Hough transform, Line fitting, Curve fitting.
10 hrs.
Region Analysis: Region properties, External points, spatial moments, mixed spatial gray-level moments, Boundary analysis: Signature properties, Shape numbers. General Frame Works for Matching: Distance relational approach, Ordered- structural matching, View class matching, Models database organization. Knowledge Based Vision: Knowledge representation, Control strategies, Information integration, Application
TEXT BOOKS
1. Dude, Hart, and Stock, "Pattern Classification", John Wiley and Sons, 2nd edition, 2001. 2. Gose, Johnsonbaugh and Jost, "Pattern Recognition and Image Analysis", Prentice Hall; Har/Dsk edition (May 1996).
REFERENCE BOOK
1. Milan Sonka,Vaclav Hlavac, Roger Boyle, "Image Processing, Analysis, and Machine Vision" (Mar. 19, 2007). 2. Robert Haralick and Linda Shapiro, "Computer and Robot Vision", Vol I, II, Addison-Wesley, 1993.
SATHYABAMA UNIVERSITY
SICX1019
L 3
T 0
P 0
Credits 3
10 hrs.
Process description in diagrammatic and functional block details raw materials preparation operation of blast furnace (BF) and auxiliary units including stoves basic oxygen furnace (BoF) electric furnace (EF) open hearth furnace (OHF) relative merits of various steel making furnaces.
10 hrs.
Quality of steel impurities present and allowed limits for usable steel waste recycling. Continuous casting and batch casting of steel primary and secondary rolling features of cold rolling steel finishing operations.
10 hrs.
Identification of various process parameters in the industry selection of suitable measurement hardware for temperature, pressure, level, flow, weighing and proportioning special gauges for measurement of thickness and shape Control room layout for mill operations graphic displays alarm management.
10 hrs.
Special applications for controls Blast Furnace (BF) Stove combustion control system gas and water control system in Basic Oxygen Furnace (BoF) Mould Level control system in Strand Casting operations.
10 hrs.
Evolution of computer applications in the industry Review of data logging, SCADA, DDC and DCS. Practices for model calculating and data logging steel rolling mill control annealing process control utilities management with computer system.
TEXT BOOK:
1. Liptak, Bela G, Instrumentation in the Processing Industries, Chilton Publishers, 1973.
REFERENCE BOOKS:
1. Considine D. M., Process/Industrial Instruments and control Handbook, McGraw Hill, 4th edition 1993. 2. Serope Kalpakjian, Manufacturing Engineering and Technology, Addison Wesley Publishing Company, Massachusetts,3rd edition, 1995. 3. Robert H. Perry, D.W. Green and J.O. Maloney, Perrys Chemical Engineers, Handbook, McGraw Hill Inc, New York, 7th ed, 1998.
SATHYABAMA UNIVERSITY
SCSX1021
ARTIFICIAL INTELLIGENCE
(Common to CSE, ECE, EEE, EIE, ETCE & E&C)
L 3
T 0
P 0
Credits 3
10 hrs.
Introduction Foundations of AI History of AI Intelligent agent Types of agents - Structure Problem solving agents Uninformed search strategies Breadth first search Uniform cost search Depth first search Depth limited search Bidirectional search Searching with partial Information.
10 hrs.
Informed search Strategies A* Heuristic function Hill Climbing Simulated Annealing Constraint Specification problem Local Search in continuous space Genetic algorithm Optimal decisions in games - Pruning - Imperfect decisions Alpha-Beta pruning Games that include an element of chance.
10 hrs.
Knowledge based agent The Wumpus world environment Propositional logic Inference rules First-order logic Syntax and semantics Situation calculus Buliding a knowledge base Electronic circuit domain Ontology Forward and backward chaining Resolution Truth maintenance system.
10 hrs.
Planning Representation of planning Partial order planning Planning and acting in real world Acting under uncertainty Bayess rules Semantics of Belief networks Inference in Belief networks Making simple decisions Making complex decisions.
10 hrs.
Learning from observation Learning decision trees Ensemble learning Learning general logical descriptions Computational learning theory Neural networks Applications Reinforcement learning Passive reinforcement Active reinforcement Communication as action Types of communicating agents Parsing DCG Semantic interpretation.
REFERENCE BOOKS:
1. Stuart J.Russel , Peter Norvig , Artificial Intelligence A Modern Approach, Pearson Education, 2nd Edition. 2. Elaine Rich , Kevin Knight , Artifical Intelligence , Tata McGraw Hill , 2nd Edition.
SATHYABAMA UNIVERSITY
SCSX1009
L 3
T 0
P 0
Credits 3
UNIT I INTRODUCTION
10 hrs.
Central Processing Unit Introduction General register organization Stack organization Instruction formats Addressing modes Data transfer and manipulation Progam control RISC Data representation Basic computer organization Instruction codes Computer registers Computer instructions Timing and control Instruction cycle Register transfer and microoperations Register transfer language Register transfer Bus and memory transfers Arithmetic ,Logic, Shift Microoperations Arithmetic logic shift unit.
10 hrs.
Computer arithmetic Addition Subtraction Multiplication and Division algorithms Floating point arithmetic operations - Microprogrammed Control Control memory Address sequencing Microprogram Example Design of control unit.
10 hrs.
Memory Organization Memory hierarchy Main memory Auxiliary memory Associative memory Cache memory Virtual memory Memory managemant hardware. Input-Output Organization Peripheral devices I/O interface Asynchronous data transfer Modes of transfer Priority interrupt DMA IOP Serial communication.
10 hrs.
Parallel processing Pipelining Arithmetic pipeline Instruction pipiline RISC pipeline Vector processing Array processors.
UNIT V MULTIPROCESSORS
10 hrs.
Characteristics of multiprocessors Interconnection structures Interprocessor arbitration Interprocessor communication and synchronization Cache coherance.
REFERENCE BOOKS:
1. M.Morris Mano, Computer system Architecture, Prentice-Hall Publishers, 3rd Edition. 2. John P Hayes , Computer architecture and Organization, McGraw Hill international edition, 3rd Edition. 3. Kai Hwang and Faye A Briggs, Computer Architecture and Parallel Processing, McGraw Hill International edition,1995.
SATHYABAMA UNIVERSITY
SEEX1013
POWER ELECTRONICS
(Common to EEE, EIE, ECE, ETCE & E&C)
L 3
T 0
P 0
Credits 3
10 hrs.
Overview of V-I characteristics of switching devices Power Diode, BJT, Switching characteristics of power MOSFETS, IGBT and Thyristor SCR Protection circuits firing circuits Commutation techniques.
10 hrs.
Principle of phase controlled converter operation single phase semi converter & full converter with R, RL & RLE load Freewheeling diode Inverter operation of full converter Three phase Semi converter & full converter with RLE load.
10 hrs.
AC AC Chopper: Single phase AC voltage controllers with R & RL load Multistage sequence control. Single phase step up and step down cycloconverters.
UNIT IV INVERTERS
10 hrs.
Principle of operation : Single phase half bridge & full bridge voltage source inverters Three phase Voltage source inverters (1200 and 1800 mode) Single phase current source inverter. PWM techniques : Single pulse PWM, Sinusoidal PWM, Modified sinusoidal PWM and multiple PWM
UNIT V APPLICATIONS
10 hrs.
SMPS : Flyback and Push Pull UPS : Redundant and Non-Redundant HVDC Transmission systems Single phase full converter fed DC drives. Inverters for standalone and gird connected photovoltaic systems. Total No of Hours: 50 hrs.
TEXT BOOKS:
1. Rashid M.H., Power Electronics circuits Devices and Applications, Prentice Hall, 3rd Edition, New Delhi, 2004 2. P.S.Bimbhra, Power Electronics, Khanna Publishers, 3rd Edition, 2003
REFERENCE BOOKS:
1. 2. 3. 4. P.C.Sen, Power Electronics, Tata Mc Graw Hill Company, New Delhi, 1987. M.D.Singh and K.B.Khanchandani, Power Electronics TMH, New Delhi, 2nd edition, 2007. Dubey G.K., Doradla S.R., Joshi A and Sinha R.M., Thyristorised Power Controllers Wiley Eastern Limited 1986. Ned Mohan, Power Electronics, 2nd Edition, 2001.
73
REGULATIONS 2010
SATHYABAMA UNIVERSITY
SMEX1017
L 3
T 0
P 0
Credits 3
10 hrs.
Operations Research(OR)-Nature-Characteristics-Phases.-Role of OR in Decision making- Outline of OR Models Linear Programming Formulation of L.P.problems Solution by graphical method, simplex method, and big M methods Applications of O.R. in production management
10 hrs.
Transportation problem Initial Basic feasible solution- Northwest corner method, Least Cost method, Vogels approximation method Test for optimality-MODI method Assignment problems- Hungarian assignment models- Travelling salesman problems
10 hrs.
Problem of Sequencing Problem with N jobs and 2 machines N Jobs 3 m/cs and 2 Jobs m m/cs (Graphical method). Project Management Basic concepts Network construction and scheduling CPM & PERT Program evaluation and resource leveling by network techniques, time Cost trade off.
10 hrs.
Inventory Control Various Types of inventory models deterministic inventory models Production model, Purchase model with and without shortage- EOQ Buffer stock Shortage quantity, Probabilistic inventory models Quantity Discount and Price Breaks Simulation Use, advantages & limitations, Monte Carlo simulation, application to queuing, inventory & other problems
10 hrs.
Queuing theory Poisson arrivals and exponential service times, Single channel models only. Game theory-Pay off matrix, competitive games with pure strategy, minimax criterion, principles of dominance &mixed strategies Replacement policy for items whose maintenance cost increases with time- Consideration of time value of money value- Replacement policy- Individual, Group replacement of items that fail completely
TEXT BOOK:
1. Kanti Swarup, P.K.Gupta, & Manmohan., "Operations Research" S. Chand & Sons.
REFERENCE BOOKS:
1. 2. 3. 4. 5. K.V.Mital and C.Mohan, "Optimization Methods in O.R and System Analysis", New Age International Publishers. S.D.Sharma, "Operations Research", Kedarnath Ramnath & Co, 2002. Hamdy A. Taha, "Operations Research", 5th Edition, PHI, 1995 Hiller & Liberman, "Introduction to Operation Research", 5th Edition, McGraw Hill, 2001. Ravindran, Phillips & Solberg, "Operations Research: Principles and Practice", 2nd Edition, Wiley India Ltd, 2007
SATHYABAMA UNIVERSITY
SICX1021
L 3
T 0
P 0
Credits 3
10 hrs.
Principles of light propagation through a fiber different types of fibers and their properties transmission characteristics of optical fiber absorption losses scattering losses-dispersion optical fiber measurement optical sources optical detectors LED-LD-PIN and APD.
10 hrs.
Fiber optic sensors fiber optic instrumentation system different types of modulators detectors application in instrumentation interferometric method of measurement of length moir fringes measurement of pressure, temperature, current, voltage, liquid level and strain fiber optic gyroscope polarization maintaining fibers.
10 hrs.
Fundamental characteristics of Lasers three level and four level lasers properties of laser laser modes resonator configuration Q-switching and mode locking cavity dumping types of lasers gas lasers, solid lasers, liquid lasers semi conductor lasers.
10 hrs.
Laser for measurement of distance, length, velocity, acceleration, current, voltage and atmospheric effect material processing laser heating, welding melting and trimming of materials removal and vaporization.
10 hrs.
Holography basic principle, methods, holographic interferometry and applications, holography for non-destructive testing holographic components- medical applications of lasers laser and tissue interaction laser instruments for surgery, removal of tumors of vocal cords, brain surgery, plastic surgery, gynecology and oncology.
TEXT BOOK:
1. Ghatak A.K. and Thiagarajar K, Optical Electronics Foundation Book, TMH, New Delhi, 1991.
REFERENCE BOOKS:
1. 2. 3. 4. John and Harry, Industrial lasers and their applications, McGraw Hill, 1974. John F Ready, Industrial applications of lasers, Academic Press, 1978. Monte Ross, Laser applications, McGraw Hill, 1968. Jasprit Singh, Semi conductor Optoelectronics, McGraw Hill, 1995.
SATHYABAMA UNIVERSITY
SECX1020
NANO ELECTRONICS
(Common to EEE, BIO-MED, EIE, E&C, ETCE, ECE, CSE & IT)
L 3
T 0
P 0
Credits 3
10 hrs.
Electronic states in crystal energy bands, Concepts of 2D nanostructures (quantum wells), 1 D nanostructures (quantum wires) OD nanostructures (quantum dots), artificial atomic clusters.
10 hrs.
Size dependent properties, Size dependent absorption spectra, Blue shift with smaller sizes, Phonons in nanostructures, Contacts at Nano level, AFM.lSTM tip on a surface.
10 hrs.
Charging of quantum dots, Coulomb blockade, Quantum mechanical treatment of quantum wells, wires and dots, Widening of bandgap in quantum dots, Strong and weak confinement, Properties of coupled quantum dots, Optical scattering from Nan defects.
10 hrs.
Nanocomposites Electronic and atomic structure of aggregates and nanoparticles Theory and modeling of nanoparticles fictionalization processes.
10 hrs.
Nanosystems: Synthesis and chacterization Methods of Synthesis: Molecular beam epitaxy, MOCVD, chemical routes, nanoparticles on polymers, pulsed laser deposition, ion beam assisted techniques including embedded nanoparticles, RF sputtering. Total Hours: 50
TEXT BOOKS:
1. K.Bamam and D.Vvedensky ,Low Dimensional Semiconductor Structures, (Cambrige University Book) 2001.
REFERENCE BOOKS:
1. L.Banyai and S.W.Koch ,Semiconductor Quantum Dots, (World Scientific) 1993, http://www.nanotec.org.uklworkshop.october03health.htm(for health and safety aspects of nanostructures) 2. J.H. Davies, An introduction to the physics-af low dimensional semiconductors, Cambridge Press, 1998. 3. Karl Goser, Peter Glosekotter, Jan Dienstuhl Nanoelectronics and Nanosystems , Springer, 2004 4. Krause P. C. and Wasynczuk O., Electromechanical Motion Devices, McGraw-Hill, New York, 1989.Lyshevski S. E., Electromechanical Systems, Electric Machines, andApplied Mechatronics, CRC Press, FL, 1999. 5. Lyshevski S. E., "Integrated control of microactuators and integrated circuits: a new turning approach in MEMS technology," Proceedings Conference Decision and Control, Phoenix, AZ, pp. 2611-2616, 1999.
SATHYABAMA UNIVERSITY
SECX1022
L 3
T 0
P 0
Credits 3
UNIT I INTRODUCTION
10 hrs.
MEMS-Micro fabrications for MEMS -Surface micromachining of silicon -Wafer bonding for MEMS-LIGA process-Micromachining of polymeric MEMS devices -Three-dimensional microfabrications.Materials: Materials for MEMS - Metal and metal alloys for MEMS - Polymers for MEMS - Other materials for MEMS.Metals : Evaporation Sputtering. Semiconductors :Electrical and chemical properties-Growth and deposition.Thin films for MEMS and their deposition techniques -Oxide film formation by thermal --oxidation -Deposition of silicon dioxide and silicon nitride -Polysilicon film deposition -Ferroelectric thin films. Materials for polymer MEMS :Classification of polymers -UV radiation curing -SU-8 for polymer MEMS.
10 hrs.
Piezoresistive sensing - Capacitive sensing - Piezoelectric sensing - Resonant sensing - Surface acoustic wave sensors. Electromechanical Transducers: transducers-Piezoelectric transducers -Electrostrictive transducers -Magnetostrictive transducers -Electrostatic actuators-Electromagnetic transducers -Electrodynamic transducersActuators: Electrothermal actuators-Comparison of electromechanical actuation schemes.
10 hrs.
Micromachning : Bulk micromachining for silicon-based MEMS -Isotropic and orientation-dependent wet etching - Dry etching -Buried oxide process -Silicon fusion bonding -Anodic bonding -Silicon surface micromachining Sacrificial layer technology - Material systems in sacrificial layer technology - Surface micromachining using plasma etching -Combined integrated-circuit technology and anisotropic wet etching.
UNIT IV LITHOGRAPHY
10 hrs.
Microstereolithography for polymer MEMS -Scanning method -Two-photon microstereolithography Surface micromachining of polymer MEMS -Projection method -Polymeric MEMS architecture with silicon, metal and ceramics -Microstereolithography integrated with thick film lithography.
UNIT V APPLICATIONS
10 hrs.
Switching: Introduction- Switch parameters- Basics of switching - Mechanical switches-Electronic switchesSwitches for RF and microwave applications - Mechanical RF switches - PIN diode RF switches - Metal oxide semiconductor field effect transistors and monolithic microwave integrated circuits. RF MEMS switches: Integration and biasing issues for RF switches -Actuation mechanisms for MEMS devices-Electrostatic switching - Approaches for low-actuation-voltage switches - Mercury contact switches -Magnetic switching - Electromagnetic switching - Thermal switching.Dynamics of the switch operation: Switching time and dynamic response - Threshold voltage. MEMS switch design, modeling and evaluation:Electromechanical finite element analysis - RF design - MEMS switch design considerations. Total Hours: 50
TEXT BOOK:
1. Vijay K.Varadan, K.J.Vinoy and K.A.Jose, RF MEMS and Their Applications(ISBN 0-470-84308-X), 1 st edition, John Wiley & Sons Ltd., West Sussex, England, 2003.
REFERENCE BOOKS :
1. 2. 3. 4. 5. P. Rai-choudhury, MEMS and MOEMS Technology and Applications, 1st Edition PHI, 2009. S. Senturia, "Microsystem Design", Kluwer, 2001. J.W. Gardner, V.K. Varadan, O.O. Awadelkarim, "Microsensors, MEMS & Smart Devices" John Wiley, 2001. S. Campbell, "The Science and Engineering of Microelectronic Fabrication", Oxford Univ. Press, 2001 N Maluf, "An Introduction to Microelectromechanical Systems Engineering", Artech House.