Professional Documents
Culture Documents
Raspberry Pi - Boards (Elinux)
Raspberry Pi - Boards (Elinux)
org
Page 1 of 16
RaspberryPi Boards
From eLinux.org
Hardware versions/revisions
Several different boards have been found probably from different assembly lines, and the following table tries to help you identify your board for better troubleshooting. These differences are being debated on raspberrypi.org on this thread [1] (http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=9524&start=25) For what we can see for model B boards there are mainly two versions that differ on the type RAM used, Samsung (S) and Hynix (H). Note: For Board ver. we used: <model><RAM Maker><production date> (ex.: BS1218 is "Model B, Samsung RAM, 18th week of 2012") Look for the date of manufacturing printed with the year and week (back side, board edge near LAN connector). In this example year (2012) and week (18th):
USB Chip C6
F1 / F2 Ref. & Ohm RG2 Reported issues / Feedback Front Back Distributor Owner
N/A
N/A
17-33G RQB44
None
RS
AndrewS
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 2 of 16
Model B:
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 3 of 16
Board ver.
BS1321
None/None
17-33G RQC18
None
Micron BM1320
3DAI8 D9QHN CZ22
SMSC
LAN9512-JZX 81319-A1B17 3194KQA CTI-TW 220 CFP 3G6
None/None
SE8117T33 1304-LF
None
Samsung AS1251
301 K4P4G324EB-AGC1 GKKS23HAU
SMSC
LAN9512-JZX 81244-A1817 BR1525858 CTI-TW 220 CFP 2BD
None/None
17-33G RQB44
None
Samsung BS1240
301 K4P4G324EB-AGC1 GKI3619P
SMSC
LAN9512-JZX B1231-A1B17 8R151387B CTI-TW 220 CFP 2GO
None/None
17-33G RSB39
None
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 4 of 16
?/? ?
None
BS1215 Samsung
SMSC SMSC
n2 220 UD
?/?
None
Samsung BS1215
216 K4P2G324ED-AGC1 GA30419V
14
LAN9512-JZX B1211-A1B17 BR149884A CTI-TW n2 220C UD
?/?
SE8117733 943-1F
None
Samsung BS1301
301 K4P4G32F4EB-AGC1 GKL438GHU (512MB version)
SMSC
LAN9512-JZX 81244-A1817 BR1525858 CTI-TW 220 CFP 28D
N/A
17-33G RQB44
None
Samsung BS1218
216 K4P2G324ED-AGC1 GAL0839V
SMSC
LAN9512-JZX B1212-A1B17 BR149884S 220 16V EE5
None
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 5 of 16
Samsung BS1218
216 K4P2G324ED-AGC1 GAJ0419C
SMSC
LAN9512-JZX B1212-A1B17 BR149884S 220 16V EE5
None
Hynix BH1208
H9TKNNN2GDMP LANDM 149A
SMSC
LAN9512-JZX B1134-A1B17 8R147769B STA-SG 220 16V EE2
14
SE8117T33 1001-LF
No issues after getting a good power supply Note the SMSC is 8R149482C which I suspect is the same for the others. Ethernet: LU1S041ALF 1018M
Hynix BH1219
H9TKNNN2GDMP LANDM 218A
SMSC
LAN9512-JZX B1206-A1B17 8R149471A CTI-TW 220 16V 2E2
T014
SE8117T33 1217-LF
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 6 of 16
Hynix BH1218
H9TKNNN2GDMP LRNOM 217A
SMSC
LAN9512-JZX B1215-A1B17 BR1501888 2E 220 16H
14 6.4 / 5.0
SE8117T33 1213-LF
USB/Keyboard/LAN issues
Hynix BH1218
H9TKNNN2GDMP LRNDM 217A
SMSC
LAN9512-JZX B1215-A1817 BR1494828 2E 220 16H
14 6.1 / 5.6
SE8117T33 1213-LF
"I haven't had any issues"[2] (http://www.raspberrypi.org/phpBB3/viewtopic.php? f=28&t=9524&start=50) Ethernet HR901110A 1211 E2112RSV1.0B1.1
?/?
SE8117T33 1213-LF
None
?/?
None
?/?
<blank>
None
RaspberryP C-Back.jpg
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 7 of 16
Hynix BH1213
h9tknnn2c0mp landm 1494
SMSC 14
n2 lan9512-jzx b1134 a1b17 8r14 220c UD 77698 sta-sg
?/?
<blank>
"pretty stable"
Samsung BS12xx
216 k4p 26324ED agc1
SMSC ?
lan9512-jzx b1212 a1b17 br149884b cti-tw 220 16V EE5
?/?
Hynix BH1218
h9trnnn2g0mp lrndm 217a
SMSC
lan9512-jzy b1215-a1b17 ase-tw 2e 220 16h
14 ?/?
Se8117t33 12-13 cf
8.2 / 5.9
SE8117T33 1213-LF
6-7 / 6-7
None
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 8 of 16
?/?
None
RaspberryPi-B
SE8117T33 1213-LF
?/?
None
Hynix BH1218
H9TKNNN2GDMP LANDM 217A
SMSC 14
LAN9512-JZX B1215-A1B17 BR150188B ASE-TW (e3) 2E 220 16H
6.9 / 5.9
SE8117T33 1213-LF
None
Hynix BH1218
H9TKNNN2GDMP LANDM 218A
SMSC 14
LAN9512-JZX B1215-A1B17 BR150188A ASE-TW (e3) 2E 220 16H
?/?
SE8117T33 1213-LF
None
Hynix BH1218
H9TKNNN2GDMP LRNOM 217A
SMSC 14
LAN9512-JZX B1215-A1B17 8R150188B ASE-TW (e3) 2E 2216H
?/?
SE8117T33 1213-LF
D1 shorted when attaching a Neewer HDMI to VGA adapter. The adapter has had no other tests and the raspberry pi's HDMI output has not been connected to any other devices before or since.
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 9 of 16
Hynix BH1208
H9TKNNN2GDMP LANDM 149A
SMSC ?
LAN9512-JZX B1134-A1B17 BR147769B STA-SG 220 16V EE2
?/?
SE8117T33 1001-LF
Stable, powers up off any charger. Powers off laptop USB without any issues Ethernet: LU1S041ALF 1018M
Hynix BH1213
H9TKNNN2GDMP LANDM 149A
SMSC ?
LAN9512-JZX B1134-A1B17 BR147769B STA-SG n2 220C UD
?/?
SE8117T33 943-LF
Hynix BH1218
H9TKNNN2GDMP LANDM 217A
SMSC 14
LAN9512-JZX B1216-A1B17 8R149482C ASE-TW (e3) 2E 220 16H
14 / 5.1
SE8117T33 1213-LF
Up headless with Squeeze and Wheezy for ~six weeks, light duty, no problems Ethernet: HR901110A 1211
Samsung BS1218
SMSC T014
220 16V EE5
T014 / ?
SE8117T33 1213-LF
Comes upp headless with Wheezy, not tested extensively Ethernet: HR901110A 1218
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 10 of 16
Samsung BS1219
216 K4P2G324ED-AGC1 GAL0859V
SMSC
LAN9512-JZX B1216-A1B17 8R149482C ASE-TW (e3) 2E 220 16H
First had problems (freezing, no LAN, etc.) due to low quality power supply - cheap ebay adaptor. Solved with own PSU construction with 7805 stabiliser adjusted to 5.25V. Now works OK with Raspbian wheezy, but not yet tested extensively. Ethernet: HR901110A 1220 F3 0.3ohm
Samsung BS1219
216 K4P2G324ED-AGC1 GAL0859D
SMSC
LAN9512-JZX B1216-A1B17 8R149482C ASE-TW (e3) 2E 220 16H
SE8117T33 0941-LF
Hynix BH1222
H9TKNNN2GDMP LANDM 214A
SMSC
LAN9512-JZX B1215-A1B17 8R148168E ASE-TW (e3) 2E 220 16H
SE8117T33 1217-LF
Samsung BS1224
222 K4P2G324ED-AGC1 GAA0419T
SMSC
LAN9512-JZX B1222-A1B17 8R150543C CTI-TW (e3) 2F 220 16H
SE8117T33 1217-LF
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 11 of 16
Samsung BS1224
222 K4P2G324ED-AGC1 GAA0519H
SMSC
LAN9512-JZX B1223-A1B17 8R15D81DA CTI-TW (e3) 2F 220 16H
SE8117T33 1220-LF
Ethernet: HanRun HR901110A 1225 No Issues Note: F1 and F2 are black 0 ohm resistors instead of green polyfuses
Samsung BS1218
216 K4P2G324ED-AGC1 GAL0839R
SMSC
LAN9512-JZX B1215-A1B17 8R150188B ASE-TW (e3)
F014
2E 220 16H
?/?
SE8117T33 1213-LF
None
Samsung BS1222
225 K4P2G324ED-AGC1 GAC0289E
SMSC
LAN9512-JZX B1227-A1B17 8R1511968 CTI-TW (e3) 2F 220 16H
SE8117T33 1217-LF
Ethernet: HanRun HR901110A 1228 Both boards by wcfields ordered at the same time/date. Note: F1 and F2 are black 0 ohm resistors instead of green polyfuses Ethernet: HanRun HR901110A 1228 Both boards by wcfields ordered at the same time/date. Note: F1 and F2 are black 0 ohm resistors instead of green polyfuses
Samsung BS1232
225 K4P2G324ED-AGC1 GAC0289H
SMSC
LAN9512-JZX B1227-A1B17 8R151261A CTI-TW (e3) 2F 220 16H
SE8117T33 1225-LF
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 12 of 16
Samsung BS1228
234 K4P2G324ED-AGC1 GAK1229X
SMSC
LAN9512-JZX B1228-A1B17 8R151303B CTI-TW (e3) 2E 220 16H
SE8117T33 1220-LF
Serious problems with the 4GB SDHC-Card ordered with the board on initial testing with Gentoo (corrupted FS) Same issues using rasbian and two different supported SD cards Using RS original power adapter
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 13 of 16
Ethernet Jack: No visible branding PS: 500mA Mobile phone charger & USB Port on Laptop and Desktop (These are all I had). Works with blackberry 8520 550mA charger. Fuse(s): ONLY seems to have green polyswitch (F3) on bottom side of board F1 and F2 don't exist In the position of the (other fuses) there is a mounting hole, likewise there is also a mounting hole under the Raspberry Pi Logo. Samsung BS1233
231 K4P4G324EB-AGC1 GKG0609V (512MB version)
SMSC
LAN9512-JZX B1227-A1B17 8R151261A CTI-TW (e3) 2E 220 CFP 2G6
There is also an extra header (P5) defined on the bottom side of the PCB near P1 (which is on the top side) Won't boot with a known working (This same card will boot on BS1215 ) Kingston 4GB Class 4 SD Card, Raspbian "wheezy" 2012-09-18. When using raspbmc powered with 550ma blackberry 8520 charger, keyboard and mouse disconnects frequently also external hard drive unmounts frequently. When using torrents and connected with usb wireless adapter (tested with Netgear WNA1000M), when torrent picks up speed, raspbian becomes unstable. Same works well over Ethernet. The unit WILL boot from the SD card bought from Element 14. Will add more when I know more.
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 14 of 16
Samsung BS1236
225 K4P46324EB-AGC1 GKEM509X (512MB version)
SMSC
LAN9512-JZX B1232-A1B17 8R151680A CTI-TW (e3) 2F 220 16H
SE8117T33 1225-LF
Ethernet Jack: HanRun HT901110A 1228 Seems to randomly power off on 3 different PS's (650mA, 900mA and 1A) (http://www.raspberrypi.org/phpBB3/viewtopic.php? f=28&t=22353) Extra header, F1, F2 and F3 and mounting holes just like BS1233
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 15 of 16
Samsung BS1238
225 K4P4G324EB-AGC1 GKFX1390 (512MB version)
SMSC
LAN9512-JZX B1232-A1B17 8R151549A CTI-TW (e3) 2H 220 16H
SE8117T33 1225-LF
Ethernet Jack: HanRun HR901110A 1230 With extra header P5, missing fuses F1 and F2, and with mounting holes just like BS1233 Weird stability problems. Can build Quake3, and can play it for a little while, but eventually locks up (black screen, loses ethernet link). Putting it in the Adafruit case seems to exacerbate the problem. Highest temp measured by vcgencmd measure_temp is 53.5C. Last measured temp before lockup was 53.0C Problem occurs with both the Adafruit power supply as well as my Nexus 7 2A supply. Tested with at least 3 different Micro-USB cables. Tested with the 4GB Dane-Elec Class 4 MicroSD card from Adafruit, as well as an 8GB Class 10 SanDisk full-size SD card. Voltages: Idle, with HDMI only 5.06V (polyfuse in) 4.82V (polyfuse out) Idle, with HDMI, keyboard and mouse 5.04V (polyfuse in) 4.77V (polyfuse out) Running Quake (with HDMI, keyboard, mouse, and network) 4.98V (polyfuse in) 4.55V (polyfuse out) Ethernet: HanRun HR901110A 1247 Quake 3 crashes and reboots near instantly after rendering the arena when overclocked (Turbo) Prone to SD card (SDHC 4 GB Class 4) corruption after a force halt when overclocked (High+)
Hynix BH1310
H9TKNNN4GDMP LRNDM 305A
SMSC
LAN9512-JZX 81303-A1B17 3032AWA CTI-TW L2 220 16H
RPi-BH131 BrianXP7.j
N/A
SE8117T33 1244-LF
http://elinux.org/RaspberryPi_Boards
28/10/2013
Page 16 of 16
Retrieved from "http://elinux.org/index.php?title=RaspberryPi_Boards&oldid=281204" This page was last modified on 22 August 2013, at 20:24. This page has been accessed 51,144 times. Content is available under a Creative Commons Attribution-ShareAlike 3.0 Unported License.
http://elinux.org/RaspberryPi_Boards
28/10/2013