Professional Documents
Culture Documents
Lte Quick Guide
Lte Quick Guide
Lte Quick Guide
LT E stands for Long Term Evolution and it was started as a project in 2004 by telecommunication body known as the T hird Generation Partnership Project (3GPP). SAE (System Architecture Evolution) is the corresponding evolution of the GPRS/3G packet core network evolution. T he term LT E is typically used to represent both LT E and SAE LT E evolved from an earlier 3GPP system known as the Universal Mobile T elecommunication System (UMT S), which in turn evolved from the Global System for Mobile Communications (GSM). Even related specifications were formally known as the evolved UMT S terrestrial radio access (E-UT RA) and evolved UMT S terrestrial radio access network (E-UT RAN). First version of LT E was documented in Release 8 of the 3GPP specifications. A rapid increase of mobile data usag e and emerg ence of new applications such as MMOG (Multimedia Online Gaming ), mobile T V, Web 2.0, streaming contents have motivated the 3rd Generation Partnership Project (3GPP) to work on the Long -T erm Evolution (LT E) on the way towards fourth-g eneration mobile. T he main g oal of LT E is to provide a hig h data rate, low latency and packet optimized radioaccess technolog y supporting flexible bandwidth deployments. Same time its network architecture has been desig ned with the g oal to support packet-switched traffic with seamless mobility and g reat quality of service.
LTE Evolution
Year Mar 2000 Mar 2002 Mar 2005 Year 2007 November 2004 January 2008 2010 Event Release 99 - UMT S/WCDMA Rel 5 - HSDPA Rel 6 - HSUPA Rel 7 - DL MIMO, IMS (IP Multimedia Subsystem) Work started on LT E specification Spec finalized and approved with Release 8 T arg eted first deployment
All LT E devices have to support (MIMO) Multiple Input Multiple Output transmissions, which allow the base station to transmit several data streams over the same carrier simultaneously. All interfaces between network nodes in LT E are now IP based, including the backhaul connection to the radio base stations. T his is g reat simplification compared to earlier technolog ies that were initially based on E1/T 1, AT M and frame relay links, with most of them being narrowband and expensive. Quality of Service (QoS) mechanism have been standardized on all interfaces to ensure that the requirement of voice calls for a constant delay and bandwidth, can still be met when capacity limits are reached. Works with GSM/EDGE/UMT S systems utilizing existing 2G and 3G spectrum and new spectrum. Supports hand-over and roaming to existing mobile networks.
Advantag es of LTE
Hig h throug hput: Hig h data rates can be achieved in both downlink as well as uplink. T his causes hig h throug hput. Low latenc y: T ime required to connect to the network is in rang e of a few hundred milliseconds and power saving states can now be entered and exited very quickly. FDD and T DD in the same platform: Frequency Division Duplex (FDD) and T ime Division Duplex (FDD), both schemes can be used on same platform. Superior end-user experienc e: Optimized sig naling for connection establishment and other air interface and mobility manag ement procedures have further improved the user experience. Reduced latency (to 10 ms) for better user experience. Seamless Connec tion: LT E will also support seamless connection to existing networks such as GSM, CDMA and WCDMA. Plug and play: T he user does not have to manually install drivers for the device. Instead system automatically recog nizes the device, loads new drivers for the hardware if needed, and beg ins to work with the newly connected device. Simple arc hitec ture: Because of Simple architecture low operating expenditure (OPEX).
Desc ription UMT S FDD bands and T DD bands defined in 36.101(v860) T able
5.5.1, g iven below Duplexing Channel coding Mobility Channel Bandwidth (MHz) FDD, T DD, half-duplex FDD T urbo code 350 km/h 1.4 3 5 10 15 20 T ransmission Bandwidth Config uration NRB: (1 resource block = 180kHz in 1ms T T I )
6 15 25 50 75 100
5 - 100km with slig ht deg radation after 30km E2E QOS allowing prioritization of different class of service End-user latency < 10mS
T erminal Equipment (T E): T his terminates the data streams. Universal Integ rated Circ uit Card (UICC): T his is also known as the SIM card for LT E equipments. It runs an application known as the Universal Subscriber Identity Module (USIM). A USIM stores user-specific data very similar to 3G SIM card. T his keeps information about the user's phone number, home network identity and security keys etc.
T he E-UT RAN handles the radio communications between the mobile and the evolved packet core and just has one component, the evolved base stations, called eNodeB or eNB . Each eNB is a base station that controls the mobiles in one or more cells. T he base station that is communicating with a mobile is known as its serving eNB. LT E Mobile communicates with just one base station and one cell at a time and there are following two main functions supported by eNB: T he eBN sends and receives radio transmissions to all the mobiles using the analog ue and dig ital sig nal processing functions of the LT E air interface. T he eNB controls the low-level operation of all its mobiles, by sending them sig nalling messag es such as handover commands. Each eBN connects with the EPC by means of the S1 interface and it can also be connected to nearby base stations by the X2 interface, which is mainly used for sig nalling and packet forwarding during handover. A home eNB (HeNB) is a base station that has been purchased by a user to provide femtocell coverag e within the home. A home eNB belong s to a closed subscriber g roup (CSG) and can only be accessed by mobiles with a USIM that also belong s to the closed subscriber g roup.
Below is a brief description of each of the components shown in the above architecture: T he Home Subscriber Server (HSS) component has been carried forward from UMT S and GSM and is a central database that contains information about all the network operator's subscribers. T he Packet Data Network (PDN) Gateway (P-GW) communicates with the outside world ie. packet data networks PDN, using SGi interface. Each packet data network is identified by an access point name (APN). T he PDN g ateway has the same role as the GPRS support node (GGSN) and the serving GPRS support node (SGSN) with UMT S and GSM. T he serving g ateway (S-GW) acts as a router, and forwards data between the base station and the PDN g ateway. T he mobility manag ement entity (MME) controls the hig h-level operation of the mobile by means of sig nalling messag es and Home Subscriber Server (HSS). T he Policy Control and Charg ing Rules Function (PCRF) is a component which is not shown in the above diag ram but it is responsible for policy control decision-making , as well as for controlling the flow-based charg ing functionalities in the Policy Control Enforcement Function (PCEF), which resides in the P-GW. T he interface between the serving and PDN g ateways is known as S5/S8. T his has two slig htly different implementations, namely S5 if the two devices are in the same network, and S8 if they are in different networks.
2G/3G GERAN and UT RAN SGSN/PDSN-FA GGSN/PDSN-HA HLR/AAA VLR SS7-MAP/ANSI-41/RADIUS DiameterGT Pc-v0 and v1 MIP
T he home network's P-GW allows the user to access the home operator's services even while in a visited network. A P-GW in the visited network allows a "local breakout" to the Internet in the visited network. T he interface between the serving and PDN g ateways is known as S5/S8. T his has two slig htly different implementations, namely S5 if the two devices are in the same network, and S8 if they are in different networks. For mobiles that are not roaming , the serving and PDN g ateways can be integ rated into a sing le device, so that the S5/S8 interface vanishes altog ether.
S.N. 1
T his is an area throug h which the mobile can move without a chang e of serving MME. Every MME pool area is controlled by one or more MMEs on the network. 2 T he S-GW servic e areas T his is an area served by one or more serving g ateways S-GW, throug h which the mobile can move without a chang e of serving g ateway. T he T rac king areas T he MME pool areas and the S-GW service areas are both made from smaller, non-overlapping units known as tracking areas (T As). T hey are similar to the location and routing areas from UMT S and GSM and will be used to track the locations of mobiles that are on standby mode.
T hus an LT E network will comprise of many MME pool areas, many S-GW service areas and lots of tracking areas.
If we combile PLMN-ID with the MMEI then we arrive at a Globally Unique MME Identifier (GUMMEI), which identifies an MME anywhere in the world:
Finally adding the MME g roup identity and the PLMN identity with S-T MSI results in the Globally Unique T emporary Identity (GUT I).
At user plane side, the application creates data packets that are processed by protocols such as T CP, UDP and IP, while in the control plane, the radio resource control (RRC) protocol writes the sig nalling messag es that are exchang ed between the base station and the mobile. In both cases, the information is processed by the packet data converg ence protocol (PDCP), the radio link control (RLC) protocol and the medium access control (MAC) protocol, before being passed to the physical layer for transmission.
User Plane
T he user plane protocol stack between the e-Node B and UE consists of the following sub-layers: PDCP (Packet Data Converg ence Protocol) RLC (radio Link Control) Medium Access Control (MAC). On the user plane, packets in the core network (EPC) are encapsulated in a specific EPC protocol and tunneled between the P-GW and the eNodeB. Different tunneling protocols are used depending on the interface. GPRS T unneling Protocol (GT P) is used on the S1 interface between the eNodeB and S-GW and on the S5/S8 interface between the S-GW and P-GW.
Packets received by a layer are called Service Data Unit (SDU) while the packet output of a layer is referred to by Protocol Data Unit (PDU) and IP packets at user plane flow from top to bottom layers.
Control Plane
T he control plane includes additionally the Radio Resource Control layer (RRC) which is responsible for config uring the lower layers. T he Control Plane handles radio-specific functionality which depends on the state of the user equipment which includes two states: idle or connected.
Mode Idle
Desc ription T he user equipment camps on a cell after a cell selection or reselection process where factors like radio link quality, cell status and radio access technolog y are considered. T he UE also monitors a pag ing channel to detect incoming calls and acquire system information. In this mode, control plane protocols include cell selection and reselection procedures. T he UE supplies the E-UT RAN with downlink channel quality and neig hbor cell information to enable the E-UT RAN to select the most suitable cell for the UE. In this case, control plane protocol includes the Radio Link Control (RRC) protocol.
Connected
T he protocol stack for the control plane between the UE and MME is shown below. T he g rey reg ion of the stack indicates the access stratum (AS) protocols. T he lower layers perform the same functions as for the user plane with the exception that there is no header compression function for the control plane.
functions including key manag ement, establishment, config uration, maintenance and release of point to point Radio Bearers.
Packets received by a layer are called Service Data Unit (SDU) while the packet output of a layer is referred to by Protocol Data Unit (PDU). Let's see the flow of data from top to bottom: IP Layer submits PDCP SDUs (IP Packets) to the PDCP layer. PDCP layer does header compression and adds PDCP header to these PDCP SDUs. PDCP Layer submits PDCP PDUs (RLC SDUs) to RLC layer. PDCP Header Compression: PDCP removes IP header (Minimum 20 bytes) from PDU, and adds T oken of 1-4 bytes. Which provides a tremendous saving s in the amount of header that would otherwise
RLC layer does seg mentation of these SDUS to make the RLC PDUs. RLC adds header based on RLC mode of operation. RLC submits these RLC PDUs (MAC SDUs) to the MAC layer. RLC Seg mentation: If an RLC SDU is larg e, or the available radio data rate is low (resulting in small transport blocks), the RLC SDU may be split among several RLC PDUs. If the RLC SDU is small, or the available radio data rate is hig h, several RLC SDUs may be packed into a sing le PDU. MAC layer adds header and does padding to fit this MAC SDU in T T I. MAC layer submits MAC PDU to physical layer for transmitting it onto physical channels. Physical channel transmits this data into slots of sub frame.
Ac ronym BCCH
Control c hannel X
T raffic c hannel
Broadcast Control Channel Pag ing Control Channel Common Control Channel Dedicated Control Channel Multicast Control Channel Dedicated T raffic Channel Multicast T raffic Channel
X X X X X X X
Transport Channels
T ransport channels define how and with what type of characteristics the data is transferred by the physical layer. Data and sig nalling messag es are carried on transport channels between the MAC and the physical layer. T ransport Channels are disting uished by the ways in which the transport channel processor manipulates them. Following table lists the transport channels that are used by LT E:
Channel Name Broadcast Channel Downlink Shared Channel Pag ing Channel Multicast Channel Uplink Shared Channel Random Access Channel
Downlink X X X X
Uplink
X X
Physical Channels
Data and sig nalling messag es are carried on physical channels between the different levels of the physical layer and according ly they are divided into two parts: Physical Data Channels Physical Control Channels
Channel Name Physical downlink shared channel Physical broadcast channel Physical multicast channel Physical uplink shared channel
Downlink X X X
Uplink
PRACH
T he transport c hannel processor composes several types of control information, to support the low-level operation of the physical layer. T hese are listed in the below table:
Field Name Downlink control information Control format indicator Hybrid ARQ indicator Uplink control information
Downlink X X X
Uplink
Channel Name Physical control format indicator channel Physical hybrid ARQ indicator channel Physical downlink control channel Relay physical downlink control channel Physical uplink control channel
Downlink X X X X
Uplink
T he base station also transmits two other physical sig nals, which help the mobile acquire the base station after it first switches on. T hese are known as the primary synchronization sig nal (PSS) and the secondary synchronization sig nal (SSS).
T he OFDM symbols are g rouped into resource blocks. T he resource blocks have a total size of 180kHz in the frequency domain and 0.5ms in the time domain. Each 1ms T ransmission T ime Interval (T T I) consists of two slots (T slot).
Each user is allocated a number of so-called resource blocks in the time.frequency g rid. T he more resource blocks a user g ets, and the hig her the modulation used in the resource elements, the hig her the bit-rate. Which resource blocks and how many the user g ets at a g iven point in time depend on advanced scheduling mechanisms in the frequency and time dimensions. T he scheduling mechanisms in LT E are similar to those used in HSPA, and enable optimal performance for different services in different radio environments.
Advantag es of OFDM
T he primary advantag e of OFDM over sing le-carrier schemes is its ability to cope with severe channel conditions (for example, attenuation of hig h frequencies in a long copper wire, narrowband interference and frequency-selective fading due to multipath) without complex equalization filters. Channel equalization is simplified because OFDM may be viewed as using many slowly-modulated narrowband sig nals rather than one rapidly-modulated wideband sig nal. T he low symbol rate makes the use of a g uard interval between symbols affordable, making it possible to eliminate inter symbol interference (ISI). T his mechanism also facilitates the desig n of sing le frequency networks (SFNs), where several adjacent transmitters send the same sig nal simultaneously at the same frequency, as the sig nals from multiple distant transmitters may be combined constructively, rather than interfering as would typically occur in a traditional sing le-carrier system.
Drawbacks of OFDM
Hig h peak-to-averag e ratio Sensitive to frequency offset, hence to Doppler-shift as well.
SC-FDMA Technolog y
LT E uses a pre-coded version of OFDM called Sing le Carrier Frequency Division Multiple Access (SC-FDMA) in the uplink. T his is to compensate for a drawback with normal OFDM, which has a very hig h Peak to Averag e Power Ratio (PAPR). Hig h PAPR requires expensive and inefficient power amplifiers with hig h requirements on linearity, which increases the cost of the terminal and drains the battery faster. SC-FDMA solves this problem by g rouping tog ether the resource blocks in such a way that reduces the need for linearity, and so power consumption, in the power amplifier. A low PAPR also improves coverag e and the cell-edg e performance.
LTE - GLOSSARY
T erm 3GPP 3GPP2 ARIB AT IS AWS CAPEX CCSA CDMA CDMA2000 DAB DSL DVB eHSPA ET SI FDD FWT GSM HSPA HSS IEEE IPT V LT E MBMS MIMO MME NGMN OFDM OPEX PAPR PCI Desc ription 3rd Generation Partnership Project 3rd Generation Partnership Project 2 Association of Radio Industries and Businesses Alliance for T elecommunication Industry Solutions Advanced Wireless Services Capital Expenditure China Communications Standards Association Code Division Multiple Access Code Division Multiple Access 2000 Dig ital Audio Broadcast Dig ital Subscriber Line Dig ital Video Broadcast evolved Hig h Speed Packet Access European T elecommunications Standards Institute Frequency Division Duplex Fixed Wireless T erminal Global System for Mobile communication Hig h Speed Packet Access Home Subscriber Server Institute of Electrical and Electronics Eng ineers Internet Protocol T elevision Long T erm Evolution Multimedia Broadcast Multicast Service Multiple Input Multiple Output Mobility Manag ement Entity Next Generation Mobile Networks Orthog onal Frequency Division Multiplexing Operational Expenditure Peak to Averag e Power Ratio Peripheral Component Interconnect
PCRF PDSN PS QoS RAN SAE SC-FDMA SGSN T DD TTA TTC TTI UT RA UT RAN WCDMA WLAN
Policing and Charg ing Rules Function Packet Data Serving Node Packet Switched Quality of Service Radio Access Network System Architecture Evolution Sing le Carrier Frequency Division Multiple Access Serving GPRS Support Node T ime Division Duplex T elecommunications T echnolog y Association T elecommunication T echnolog y Committee T ransmission T ime Interval Universal T errestrial Radio Access Universal T errestrial Radio Access Network Wideband Code Division Multiple Access Wireless Local Area Network