Professional Documents
Culture Documents
Huawei 3g Parameters
Huawei 3g Parameters
CELLHSDPA
INDEX
Set the RNC-oriented Directed Retry Decision (DRD) algorithm parameters. The DRD algorithm is used to select a suitable cell during the cell resource admission procedure for RRC or RAB. The algor - Current cell load - Cell type - Traffic type - Intelligent networking strategy - Cell resource admission result The following functions are available: - RRC setup DRD - RAB setup DRD - RAB modification DRD - DCCC with channel switch DRD
Note
None.
Parameter
ID
Name
ServiceDiffDrdSwitch
LdbDRDSwitchDCH
LdbDRDSwitchHSDPA
LdbDRDchoice
RrcRedictSwitch
LdbDRDOffsetDCH
LdbDRDOffsetHSDPA
LdbDRDLoadRemainThd Dl load balance DRD power DCH remain threshold for DCH[%]
LdbDRDLoadRemainThd Dl load balance DRD power DCH remain threshold for DCH[%]
LdbDRDLoadRemainThd Dl load balance DRD power HSDPA remain threshold for HSDPA[%]
CodeBalancingDrdCode Code occupied rate threshold for RateThd code balance drd[%]
ReDirBandInd
ReDirBandInd
ReDirUARFCNUplink
To set the RNC-oriented DRD algorithm parameters, run the following command: SET DRD: ServiceDiffDrdSwitch=ON; After the command is run, the [ServiceDiffDrdSwitch] parameter is set to ON.
rs(SET DRD)
RD) algorithm parameters. e cell during the cell resource admission procedure for RRC or RAB. The algorithm is affected by the following factors:
Description Value range: ON, OFF. Physical unit: None. Content: This parameter specifies whether the service differential DRD algorithm will be applied. - ON: The service differential DRD algorithm will be applied. - OFF: The service differential DRD algorithm will not be applied. Recommended value: OFF. Value range: ON, OFF. Physical unit: None. Content:This parameter specifies whether the load balancing DRD algorithm will be applied for services carried on DCH. - ON: The load balancing DRD algorithm will be applied. - OFF: The load balancing DRD algorithm will not be applied. Recommended value: OFF. Value range: ON, OFF. Physical unit: None.
Content: This parameter specifies whether the load balancing DRD algorithm will be applied for services carried on HS-DSCH. - ON: The load balancing DRD algorithm will be applied. - OFF: The load balancing DRD algorithm will not be applied. Recommended value: OFF. Value range: Power~1, UserNumber~0 Physical unit: None. Content: This parameter specifies which choice the load balancing DRD algorithm will be applied. - Power: Power(Downlink none-HSDPA power is used for services carried on DCH, and downlink HSDPA guarantee power is used for services carried on HS-DSCH)will be applied to the load balancing DRD algorithm. - UserNumber: User number(Downlink R99 equivalent user number is used for services carried on DCH, and downlink HSDPA user number is used for services carried on HS-DSCH)will be applied to the the load balancing DRD algorithm. Recommended value: UserNumber. Value range: OFF~0, Only_To_Inter_Frequency~1, Allowed_To_Inter_RAT~2. Physical unit: None. Content: This parameter specifies the RRC redirection strategy. - OFF: RRC redirection is not allowed. - Only_To_Inter_Frequency: Only RRC redirection to inter-frequency cells is allowed. - Allowed_To_Inter_RAT: RRC redirection to inter-frequency cells and redirection to inter-RAT cells are both allowed. Recommended value: Only_To_Inter_Frequency. Value range: 0~100. Physical value range: 0%~100%. Physical unit: %. Content: This parameter specifies the threshold of remanent load offset between the current cell and the target cell when load balancing DRD is applied for DCH users. Only when the remanent load offset reaches this threshold can a neighboring cell be selected as a candidate DRD cell for DCH users. Recommended value: 10. Value range: 0~100. Physical value range: 0%~100%. Physical unit: %. Content: This parameter specifies the threshold of remanent load offset between the current cell and the target cell when load balancing DRD is applied for HSDPA users. Only when the remanent load offset reaches this threshold can a neighboring cell be selected as a candidate DRD cell for HSDPA users. Recommended value: 10. Value range: 0~100. Physical value range: 0%~100%. Physical unit: None. Content: This parameter specifies the downlink load threshold to trigger load balancing DRD for services carried on DCH. The load balancing DRD will probably be triggered only when the downlink cell remanent non H power or remanent R99 equivalent user number is less than this threshold.
Recommended value: 35. Value range: 0~100. Physical value range: 0%~100%. Physical unit: %. Content: This parameter specifies the downlink load threshold to trigger load balancing DRD for services carried on HS-DSCH. The load balancing DRD will probably be triggered only when the downlink cell remanent HSDPA guarantee power or remanent HSDPA user number is less than this threshold. Recommended value: 100. Value range: 0~100. Physical value range: 0%~100%. Physical unit: %. Content: This parameter specifies the threshold of the downlink remanent total power difference between the current cell and the target cell when load balancing DRD is applied and the load balancing DRD choice is Power. Only when the downlink remanent total power difference is less than this threshold can a neighboring cell be selected as a candidate DRD cell. Recommended value: 30. Value range: ON, OFF. Physical unit: None. Content: This parameter specifies whether the code balancing DRD algorithm will be applied. - ON: The code balancing DRD algorithm will be applied. - OFF: The code balancing DRD algorithm will not be applied. Recommended value: OFF. Value range: 0~100. Physical value range: 0%~100%. Physical unit: None. Content: This parameter specifies the threshold of code occupancy offset between the current cell and the target cell when code balancing DRD is applied. Only when the cell code occupancy offset reaches this threshold can a neighboring cell be selected to be a candidate cell for DRD. Recommended value: 7. Value range: SF4~0, SF8~1, SF16~2, SF32~3, SF64~4, SF128~5, SF256~6. Physical unit: None. Content: This parameter specifies one of the triggering conditions of code balancing DRD. (The other condition is the code occupancy.) This condition refers to that the minimum spreading factor of the best cell is not smaller than the value of this parameter. Recommended value: SF8. Value range: 0~100. Physical value range: 0%~100%. Physical unit: %. Content: This parameter specifies one of the triggering conditions of code balancing DRD. (The other condition is the minimum spreading factor.) This condition refers to that the code occupancy in the best cell is not lower than the value of this parameter. Recommended value: 13. Value range: Band1, Band2, Band3, Band4, Band5, Band6, Band7, Band8, Band9, DependOnNCell, BandIndNotUsed. Physical unit: None. Content: This parameter specifies the target frequency band in the redirection procedure.
Recommended value: DependOnNCell. Value range: TRUE, FALSE. Physical unit: None. Content: This parameter specifies whether the UL frequency of the target cell of redirection needs to be configured. - TRUE: The UL frequency needs to be configured. - FALSE: The UL frequency does not need to be configured. It is configured automatically according to the relationship between UL and DL frequencies. Recommended value: None. Value range: Depending on the band indication, as shown below: Band1: Common frequencies: [9612-9888] Special frequencies: none Band2: Common frequencies: [9262-9538] Special frequencies: {12, 37, 62, 87, 112, 137, 162, 187, 212, 237, 262, 287} Band3: Common frequencies: [937-1288] Special frequencies: none Band4: Common frequencies: [1312-1513] Special frequencies: {1662, 1687, 1712, 1737, 1762, 1787, 1812, 1837, 1862} Band5: Common frequencies: [4132-4233] Special frequencies: {782, 787, 807, 812, 837, 862} Band6: Common frequencies: [4162-4188] Special frequencies: {812, 837} Band7: Common frequencies: [2012-2338] Special frequencies: {2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687} Band8: Common frequencies: [2712-2863] Special frequencies: none Band9: Common frequencies: [8762-8912] Special frequencies: none BandIndNotUsed: [0-16383]
Content: This parameter specifies the target uplink UARFCN of a cell for RRC redirection. Assume that the target uplink UARFCN for RRC redirection is unspecified, the band indication is Band1, Band2, Band3, Band4, Band5, Band6, Band7, Band8, or Band9, and the target downlink UARFCN for RRC redirection is valid. Then, the default target uplink UARFCN for RRC redirection is as follows: - If the DL frequency belongs to common frequencies, then
Band1: Uplink UARFCN = Downlink UARFCN - 950 Band2: Uplink UARFCN = Downlink UARFCN - 400 Band3: Uplink UARFCN = Downlink UARFCN - 225 Band4: Uplink UARFCN = Downlink UARFCN - 225 Band5: Uplink UARFCN = Downlink UARFCN - 225 Band6: Uplink UARFCN = Downlink UARFCN - 225 Band7: Uplink UARFCN = Downlink UARFCN - 225 Band8: Uplink UARFCN = Downlink UARFCN - 225 Band9: Uplink UARFCN = Downlink UARFCN - 475 - If the DL frequency belongs to special frequencies, then Band2: Uplink UARFCN = Downlink UARFCN - 400 Band4: Uplink UARFCN = Downlink UARFCN - 225 Band5: Uplink UARFCN = Downlink UARFCN - 225 Band6: Uplink UARFCN = Downlink UARFCN - 225 Band7: Uplink UARFCN = Downlink UARFCN - 225 Recommended value: None. Value range: Depending on the band indication, as shown below: Band1 Common frequencies: [10562-10838] Special frequencies: none Band2 Common frequencies: [9662-9938] Special frequencies: {412, 437, 462, 487, 512, 537, 562, 587, 612, 637, 662, 687} Band3 Common frequencies: [1162-1513] Special frequencies: none Band4 Common frequencies: [1537-1738] Special frequencies: {1887, 1912, 1937, 1962, 1987, 2012, 2037, 2062, 2087} Band5 Common frequencies: [4357-4458] Special frequencies: {1007, 1012, 1032,1037, 1062, 1087} Band6 Common frequencies: [4387-4413] Special frequencies: {1037, 1062} Band7 Common frequencies: [2237-2563] Special frequencies: {2587, 2612, 2637, 2662, 2687, 2712, 2737, 2762, 2787, 2812, 2837, 2862, 2887, 2912} Band8 Common frequencies: [2937-3088] Special frequencies: none Band9 Common frequencies: [9237-9387] Special frequencies: none BandIndNotUsed:[0-16383]
Physical unit: None. Content: This parameter specifies the target downlink UARFCN of a cell for RRC redirection. Recommended value: None.
INDEX Add Cell Selection And Reselection Information(ADD CELLSELRESEL) Function Note Parameter Example
Function
None.
Parameter
ID
Name
CellId
Cell ID
SpeedDep endentSca Speed dependent scaling lingFactor factor for reselection delay
Add cell selection and reselection parameters to Cell1. ADD CELLSELRESEL: CellId=1, QualMeas=CPICH_ECNO, IdleQhyst1s=2, ConnQhyst1s=2, IdleQhyst2s=2, ConnQhyst2s=2, Trese After the above operations, the cell reselection parameters are added toCell1 as follows: 1.Cell Sel-reselection quality measure is CPICH Ec/No. 2.Hysteresis 1 for idle mode is 4 dB. 3.Hysteresis 1 for connect mode is 4 dB. 4.Hysteresis 2 for idle mode is 4 dB. 5.Hysteresis 2 for connect mode is 4 dB. 6.The cell reselection delay time is 1s. 7.The minimum quality level of CPICH Ec/No is -18 dB. 8.The minimum Rx level of CPICH RSCP is -116 dBm. 9.The maximum allowed uplink transmit power of a UE in the cell is 21 dBm. 10.The intra-frequency cell reselection threshold for idle state and connect state is 6 dB. 11.The inter-frequency cell reselection threshold for idle state and connect state is 10 dB. 12.The inter-RAT cell reselection threshold is 4 dB. 13.Speed dependent scaling factor for reselection is 0.2. 14.Inter-frequency scaling factor for reselection is 2.5. 15.Inter-RAT scaling factor for reselection is 2.5. 16.The non-HCS speed estimation parameters are configured. 17.The time for non-HCS maximum cell reselection is not used. 18.The non-HCS maximum number of cell reselection is 8. 19.The extra time before a UE resumes its low mobility in a non-HCS cell is not used. 20.Hysteresis 1 for UE in CELL_PCH or URA_PCH state is 5 dB. 21.Hysteresis 1for UE in CELL_FACH state is 5 dB. 22.Hysteresis 2 for UE in CELL_PCH or URA_PCH state is 5 dB. 23.Hysteresis 2 for UE in CELL_FACH state is 5 dB. 24.Reselection delay time for UE in PCH state is 3s. 25.Reselection delay time for UE in CELL_FACH state is 0.6s.
ction information.
Description Value range: 0~65535 Physical unit: None Content: Uniquely identifying a cell Recommended value: None Value range: CPICH_ECNO(CPICH Ec/N0), CPICH_RSCP(CPICH RSCP) Physical unit: None Content: Measurement quantity of cell selection and reselection. It can be set to CPICH Ec/N0 or CPICH RSCP. For detailed information of this parameter, refer to 3GPP TS 25.304. Recommended value: CPICH_ECNO Value range: 0~20 Physical value range: 0~40; step: 2 Physical unit: dB Content: The hysteresis value of the serving FDD cells in idle mode in case the quality measurement for cell selection and reselection is set to CPICH RSCP. It is related to the slow fading feature of the area where the cell is located. The greater the slow fading variance is, the greater this parameter. According to the R regulation, the current serving cell involves in cell selection after the measurement value is added with the hysteresis value. The measurement hysteresis aims to prevent the ping-pong effect of the cell reselection, which is caused by the slow fading when the UE is on the edge of the cell. The ping-pong effect may trigger frequent location updates (idle mode), URA updates (URA_PCH), or cell updates (CELL_FACH, CELL_PCH), and thus increase the load of network signaling and the consumption of UE batteries. Set a proper measurement hysteresis to reduce as much as possible effect of the slow fading as well as ensuring timely cell updates of the UE. According to the CPICH RSCP emulation report of inter-frequency hard handovers, the measurement hysteresis ranges 4 dBm to 5 dBm and is set to 4 dBm by default when the slow fading variance is 8 dB and the relative distance is 20 m. In the cells where the slow fading variance is low and the average moving speed of UEs is high, for example the suburbs and countryside, reduce the measurement hysteresis to guarantee timely location updates of UEs. The higher the measurement hysteresis is, the less likely it is for various types of cell reselections to occur, and the better the slow fading resistance capability is, but the slower the system reacts to the environment changes. For detailed information of this parameter, refer to 3GPP TS 25.304. Value range: 0~20 Physical value range: 0~40; step: 2 Physical unit: dB.
Content: The hysteresis value of the serving FDD cells in connected mode in case the quality measurement for cell selection and reselection is set to CPICH RSCP. It is related to the slow fading feature of the area where the cell is located. The greater the slow fading variance is, the greater this parameter. According to the R regulation, the current serving cell involves in cell selection after the measurement value is added with the hysteresis value. The measurement hysteresis aims to prevent the ping-pong effect of the cell reselection, which is caused by the slow fading when the UE is on the edge of the cell. The ping-pong effect may trigger frequent location updates (idle mode), URA updates (URA_PCH), or cell updates (CELL_FACH, CELL_PCH), and thus increase the load of network signaling and the consumption of UE batteries. Set a proper measurement hysteresis to reduce as much as possible effect of the slow fading as well as ensuring timely cell updates of the UE. According to the CPICH RSCP emulation report of inter-frequency hard handovers, the measurement hysteresis ranges 4 dBm to 5 dBm and is set to 4 dBm by default when the slow fading variance is 8 dB and the relative distance is 20 m. In the cells where the slow fading variance is low and the average moving speed of UEs is high, for example the suburbs and countryside, reduce the measurement hysteresis to guarantee timely location updates of UEs. The higher the measurement hysteresis is, the less likely it is for various types of cell reselections to occur, and the better the slow fading resistance capability is, but the slower the system reacts to the environment changes. For detailed information of this parameter, refer to 3GPP TS 25.304. Recommended value: 2 Value range: {{0~20},{255}} Physical value range: 0~40; step: 2 Physical unit: dB. Content: The hysteresis value of the serving FDD cells in idle mode in case the quality measurement for cell selection and reselection is set to CPICH Ec/No. It is related to the slow fading feature of the area where the cell is located. The greater the slow fading variance is, the greater this parameter. It is optional. If it is not configured, [Hysteresis 1] will be adopted as the value. This parameter is not configured when its value is 255. According to the R regulation, the current serving cell involves in cell selection after the measurement value is added with the hysteresis value. The measurement hysteresis aims to prevent the ping-pong effect of the cell reselection, which is caused by the slow fading when the UE is on the edge of the cell. The ping-pong effect may trigger frequent location updates (idle mode), URA updates (URA_PCH), or cell updates (CELL_FACH, CELL_PCH), and thus increase the load of network signaling and the consumption of UE batteries. Set a proper measurement hysteresis to reduce as much as possible effect of the slow fading as well as ensuring timely cell updates of the UE. According to the CPICH RSCP emulation report of inter-frequency hard handovers, the measurement hysteresis ranges 4 dBm to 5 dBm and is set to 4 dBm by default when the slow fading variance is 8 dB and the relative distance is 20 m. In the cells where the slow fading variance is low and the average moving speed of UEs is high, for example the suburbs and countryside, reduce the measurement hysteresis to guarantee timely location updates of UEs. The higher the measurement hysteresis is, the less likely it is for various types of cell reselections to occur, and the better the slow fading resistance capability is, but the slower the system reacts to the environment changes. For detailed information of this parameter, refer to 3GPP TS 25.304. Recommended value: the same as Qhyst1s for idle mode Value range: {{0~20},{255}}. Physical value range: 0~40; step: 2. Physical unit: dB. Content: The hysteresis value of the serving FDD cells in connected mode in case the quality measurement for cell selection and reselection is set to CPICH Ec/No. It is related to the slow fading feature of the area where the cell is located. The greater the slow fading variance is, the greater this parameter. This parameter is not configured when its value is 255.
According to the R regulation, the current serving cell involves in cell selection after the measurement value is added with the hysteresis value. The measurement hysteresis aims to prevent the ping-pong effect of the cell reselection, which is caused by the slow fading when the UE is on the edge of the cell. The ping-pong effect may trigger frequent location updates (idle mode), URA updates (URA_PCH), or cell updates (CELL_FACH, CELL_PCH), and thus increase the load of network signaling and the consumption of UE batteries. Set a proper measurement hysteresis to reduce as much as possible effect of the slow fading as well as ensuring timely cell updates of the UE. According to the CPICH RSCP emulation report of inter-frequency hard handovers, the measurement hysteresis ranges 4 dBm to 5 dBm and is set to 4 dBm by default when the slow fading variance is 8 dB and the relative distance is 20 m. In the cells where the slow fading variance is low and the average moving speed of UEs is high, for example the suburbs and countryside, reduce the measurement hysteresis to guarantee timely location updates of UEs. The higher the measurement hysteresis is, the less likely it is for various types of cell reselections to occur, and the better the slow fading resistance capability is, but the slower the system reacts to the environment changes. For detailed information of this parameter, refer to 3GPP TS 25.304. Recommended value:the same as Qhyst1s for connect mode. Value range: 0~31 Physical unit: s Content: If the signal quality (CPICH Ec/No measured by the UE) of a neighboring cell is better than that of the serving cell during the specified time of this parameter, the UE reselects the neighboring cell. It is used to avoid ping-pong reselection between different cells. Note that the value 0 corresponds to the default value defined in the protocol. Set the parameter as follows: 1. Ensure that the UE can reselect a cell when crossing the non-soft-switch area of the cell and that the UE timely performs location updates, cell updates, or URA updates when necessary. 2. Ensure that the UE does not reselect a cell when it is in the soft-switch area of the cell. In this way, the unnecessary location updates, cell updates, and URA updates are avoided. 3. Consider the difference between cells that cover different areas, for example the cells covering highways and cells covering densely populated areas. TIf the parameter is set to a comparatively low value, the ping-pong reselections may be caused. The parameter can be increased in populated area and reduced in high-speed movement. If the parameter is set to a comparatively high value, the cell reselection delay may become excessively high, and thus cell reselections may be affected. For detailed information, refer to 3GPP TS 25.304. Recommended value: 1 Value range: -24~0 Physical unit: dB Content: The minimum required quality threshold corresponding to CPICH Ec/No. The UE can camp on the cell only when the measured CPICH Ec/No is greater than the value of this parameter. The higher the parameter value is, the more difficult it is for the UE to reside in the cell. The lower parameter value is, the easier it is for the UE to reside in the cell, but it is possible that the UE cannot receive the system messages that are sent through the PCCPCH. For detailed information, refer to the 3GPP TS 25.304. Recommended value: -18 Value range: -58~-13 Physical value range: -115~-25; step: 2 (-58:-115; -57:-113; ...; -13:-25 ) Physical unit: dBm
Content: The minimum required RX threshold corresponding to CPICH RSCP. The UE can camp on the cell only when the measured CPICH RSCP is greater than the value of this parameter. The setting of Qrxlevmin should be related to Qqualmin. The higher the parameter is, the more difficult it is for the UE to reside in the cell. The lower parameter is, the easier it is for the UE to reside in the cell, but it is possible that the UE cannot receive the system messages that are sent through the PCCPCH. For detailed information, refer to 3GPP TS 25.304. Recommended value: -58 Value range: TRUE, FALSE Physical unit: none Content: Indicating whether the minimum required RX level is extended. For detailed information of this parameter, refer to 3GPP TS 25.304. Recommended value: FALSE Value range: -2, -1 Physical value range: -4, -2; step: 2 (-2: -4; -1:-2) Physical unit: none Content: Actual minimum required RX level = minimum required RX level + extended minimum required RX Recommended value: none Value range: -50~33 Physical unit: dBm Content: The maximum allowed uplink transmit power of a UE in the cell, which is related to the network planning. For detailed information, refer to 3GPP TS 25.304. Recommended value: 24 Value range: {{-16~10},{127}} Physical value range: -32~20; step: 2 Physical unit: dB Content: Threshold for intra-frequency cell reselection in idle mode. When the quality (CPICH Ec/No measured by the UE) of the serving cell is lower than this threshold plus the [Qqualmin] of the cell, the intra-frequency cell reselection procedure will be started. This parameter is not configured when its value is 127. The intra-frequency cell reselection has a priority higher than the inter-frequency cell reselection and inter-RAT cell reselection, the intra-frequency cell reselection start threshold should be higher than the inter-frequency cell reselection start threshold and inter-RAT cell reselection start threshold. If the cell reselection threshold is set to a comparatively high value, the UE may frequently start cell reselections, and the battery of the UE may be largely consumed. If the cell reselection threshold is set to a comparatively low value, it is difficult for cell reselections to be started, and the UE may not timely reside in the cells with good quality, affecting the quality of communication between the UTRAN and the UE. For detailed information, refer to 3GPP TS 25.304. Recommended value: None Value range: {{-16~10},{127}} Physical value range: -32~20; step: 2 Physical unit: dB
Content: Threshold for inter-frequency cell reselection in idle mode. When the quality (CPICH Ec/No measured by UE) of the serving cell is lower than this threshold plus the [Qqualmin] of the cell, the inter-frequency cell reselection procedure will be started. This parameter is not configured when its value is 127. The intra-frequency cell reselection has a priority higher than the inter-frequency cell reselection and inter-RAT cell reselection, the intra-frequency cell reselection start threshold should be higher than the inter-frequency cell reselection start threshold and inter-RAT cell reselection start threshold. If the cell reselection threshold is set to a comparatively high value, the UE may frequently start cell reselections, and the battery of the UE may be largely consumed. If the cell reselection threshold is set to a comparatively low value, it is difficult for cell reselections to be started, and the UE may not timely reside in the cells with good quality, affecting the quality of communication between the UTRAN and the UE. For detailed information, refer to 3GPP TS 25.304. Recommended value: None Value range: {{-16~10},{127}} Physical value range: -32~20; step: 2 Physical unit: dB. Content: Threshold for intra-frequency cell reselection in connected mode. When the quality (CPICH Ec/No measured by the UE) of the serving cell is lower than this threshold plus the [Qqualmin] of the cell, the intrafrequency cell reselection procedure will be started. This parameter is not configured when its value is 127. The intra-frequency cell reselection has a priority higher than the inter-frequency cell reselection and inter-RAT cell reselection, the intra-frequency cell reselection start threshold should be higher than the inter-frequency cell reselection start threshold and inter-RAT cell reselection start threshold. If the cell reselection threshold is set to a comparatively high value, the UE may frequently start cell reselections, and the battery of the UE may be largely consumed. If the cell reselection threshold is set to a comparatively low value, it is difficult for cell reselections to be started, and the UE may not timely reside in the cells with good quality, affecting the quality of communication between the UTRAN and the UE. For detailed information, refer to 3GPP TS 25.304. Recommended value: None Value range: {{-16~10},{127}}. Physical value range: -32~20; step: 2. Physical unit: dB. Content: Threshold for inter-frequency cell reselection in connected mode. When the quality (CPICH Ec/No measured by UE) of the serving cell is lower than this threshold plus the [Qqualmin] of the cell, the interfrequency cell reselection procedure will be started. This parameter is not configured when its value is 127. The intra-frequency cell reselection has a priority higher than the inter-frequency cell reselection and inter-RAT cell reselection, the intra-frequency cell reselection start threshold should be higher than the inter-frequency cell reselection start threshold and inter-RAT cell reselection start threshold. If the cell reselection threshold is set to a comparatively high value, the UE may frequently start cell reselections, and the battery of the UE may be largely consumed. If the cell reselection threshold is set to a comparatively low value, it is difficult for cell reselections to be started, and the UE may not timely reside in the cells with good quality, affecting the quality of communication between the UTRAN and the UE. For detailed information, refer to 3GPP TS 25.304. Recommended value: None. Value range: {{-16~10},{127}} Physical value range: -32~20; step: 2 Physical unit: dB
Content: Threshold for inter-RAT cell reselection. When the quality (CPICH Ec/No measured by UE) of the serving cell is lower than this threshold plus the [Qqualmin] of the cell, the inter-RAT cell reselection procedure will be started. This parameter is not configured when its value is 127. This parameter is not configured when its value is 127. The intra-frequency cell reselection has a priority higher than the inter-frequency cell reselection and interRAT cell reselection, the intra-frequency cell reselection start threshold should be higher than the interfrequency cell reselection start threshold and inter-RAT cell reselection start threshold. If the cell reselection threshold is set to a comparatively high value, the UE may frequently start cell reselections, and the battery of the UE may be largely consumed. If the cell reselection threshold is set to a comparatively low value, it is difficult for cell reselections to be started, and the UE may not timely reside in the cells with good quality, affecting the quality of communication between the UTRAN and the UE. For detailed information, refer to 3GPP TS 25.304. Recommended value: None Value range: {{{0~10},{255}} Physical value range: 0~1; step: 0.1 Physical unit: None Content: For a high-mobility UE, multiples this parameter by its reselection delay to reduce the reselection delay of the UE. This parameter can be set to 10 for middle-speed UE, which means no influence upon reselection delay time. This parameter is not configured when its value is 255. For detailed inforamtion, refer to 3GPP TS Recommended value: None Value range: {{4~19},{255}} Physical value range: 1~4.75.step: 0.25 Physical unit: None Content: This parameter is used to increase time of inter-frequency reselection. It is not configured when its value is 255. For detailed inforamtion, refer to 3GPP TS 25.304. Recommended value: None Value range: {{4~19},{255}} Physical value range: 1~4.75.step: 0.25 Physical unit: None Content: This parameter is used to increase time of inter-RAT reselection. It is not configured when its value is 255. For detailed inforamtion, refer to 3GPP TS 25.304. Recommended value: None Value range: CONFIGURED, NOT_CONFIGURED Physical unit: None Content: Indicating whether the non-HCS speed estimation parameter should be configured. Recommended value: None Value range: not used, D30, D60, D120, D180, D240 Physical value range: not used, 30, 60, 120, 180, 240 Physical unit: s Content: Maximum duration of non-HCS cell reselection. If the number of cell reselection exceed the value of this parameter during Tcrmaxnonhcs, the UE is not in high-speed movement. For detailed inforamtion, refer to 3GPP TS 25.304. Recommended value:NotUsed Value range: 1~16 Physical unit: None Content: Maximum number of non-HCS cell reselection. This parameter, along with Tcrmaxnonhcs, defines the speed estimation threshold of non-HCS cells. For detailed inforamtion, refer to 3GPP TS 25.304. Recommended value: 8 Value range: not used, D10, D20, D30, D40, D50, D60, D70
Physical value range: not used, 10, 20, 30, 40, 50, 60, 70 Physical unit: s Content: Hysterisis time before non-HCS resuming slow movement. When UE is in high-speed movement, if the number of cell reselections is less than Ncrnonhcs, the UE resumes to slow movement. For detailed inforamtion, refer to 3GPP TS 25.304. Recommended value: NotUsed Value range: {{0~40},{255}} Physical unit: dB Content: This parameter indicates that in the CELL_PCH or URA_PCH connection mode, the measurement hysteresis of the UE is 1. It is used when CPICH RSCP is used in cell selection and reselection measurement. This parameter is not configured when the value is 255. Otherwise, the greater the parameter value is, the harder the cell selection happens. For detailed inforamtion, refer to 3GPP TS 25.304. Recommended value: None Value range: {{0~40},{255}} Physical unit: dB Content: This parameter indicates that in the CELL_FACH connection mode, the measurement hysteresis of the UE is 1. It is used when CPICH RSCP is used in cell selection and reselection measurement. This parameter is not configured when the value is 255. Otherwise, the greater the parameter value is, the harder the cell selection happens. For detailed inforamtion, refer to 3GPP TS 25.304. Recommended value: None Value range: {{0~40},{255}} Physical unit: dB Content: This parameter indicates that in the CELL_PCH or URA_PCH connection mode, the measurement hysteresis of the UE is 2. It is used when CPICH EcNo is used in cell selection and reselection measurement. This parameter is not configured when the value is 255. Otherwise, the greater the parameter value is, the harder the cell selection happens. For detailed inforamtion, refer to 3GPP TS 25.304. Recommended value: None Value range: {{0~40},{255}} Physical unit: dB Content: This parameter indicates that in the CELL_FACH connection mode, the measurement hysteresis of the UE is 2. It is used when CPICH EcNo is used in cell selection and reselection measurement. This parameter is not configured when the value is 255. Otherwise, the greater the parameter value is, the harder the cell selection happens. For detailed inforamtion, refer to 3GPP TS 25.304. Recommended value: None Value range: {{0~31},{255}} Physical unit: s Content: This parameter indicates the UE reselection delay in the CELL_PCH or URA_PCH connection mode. This parameter is not configured when the value is 255. Instead, the Treselections parameter is used. For detailed inforamtion, refer to 3GPP TS 25.304 Recommended value: None Value range: {{0~31},{255}} Physical value range: 0~6.2; step: 0.2 Physical unit: s
Content: This parameter indicates the UE reselection delay in the CELL_FACH connection mode. This parameter is not configured when the value is 255. Instead, the Treselections parameter is used. For detailed inforamtion, refer to 3GPP TS 25.304. Recommended value: None
ction parameters to Cell1. QualMeas=CPICH_ECNO, IdleQhyst1s=2, ConnQhyst1s=2, IdleQhyst2s=2, ConnQhyst2s=2, Treselections=1, Qqualmin=-18, Qrxlevmin=-5
the cell reselection parameters are added toCell1 as follows: measure is CPICH Ec/No.
of CPICH Ec/No is -18 dB. PICH RSCP is -116 dBm. nk transmit power of a UE in the cell is 21 dBm. eselection threshold for idle state and connect state is 6 dB. eselection threshold for idle state and connect state is 10 dB. tion threshold is 4 dB. factor for reselection is 0.2. ctor for reselection is 2.5. or reselection is 2.5. ation parameters are configured. ximum cell reselection is not used. umber of cell reselection is 8. E resumes its low mobility in a non-HCS cell is not used. L_PCH or URA_PCH state is 5 dB. _FACH state is 5 dB. L_PCH or URA_PCH state is 5 dB. L_FACH state is 5 dB. r UE in PCH state is 3s. r UE in CELL_FACH state is 0.6s.
electionspch=3, Treselectionsfach=3;
INDEX Add Inter-frequency Neighboring Cell(ADD INTERFREQNCELL) Function Note Parameter Example
Function
1. It is not mandatory to configure inter-frequency neighboring cells in pairs, e.g. Cell 2 might not be one of cell 1's neighborin 2. Before adding an inter-frequency neighboring cell, check whether this cell belongs to the local RNC or another RNC. If the c 3.One cell's inter-frequency neighbour cells with same downlink frequency and uplink frequency are limited to 32.
Parameter
ID
Name
CellId
Cell ID
RncId
NCellId
Neighboring cell ID
SIB11Ind
SIB11 Indicator
SIB12Ind
SIB12 Indicator
NPrio
To add for the cell 1 an inter-frequency neighboring cell 100 with the following configuration: 1. RNC ID of neighboring cell: 9 2. Neighboring cell ID: 100 3. Cell offset: 0 4. SIB11 Indicator: TRUE 5. SIB12 Indicator: FALSE 6. HCS Cell Reselect Penalty Timer: D0 7. The priority of coverage based inter-frequency handover: 1 8. Blind handover flag: FALSE 9. The flag of the priority: FALSE Execute the following command: ADD INTERFREQNCELL: CellId=1, RncId=9, NCellId=100, CIOOffset=0, SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D
o configure inter-frequency neighboring cells in pairs, e.g. Cell 2 might not be one of cell 1's neighboring cells while cell 1 is cell 2's. er-frequency neighboring cell, check whether this cell belongs to the local RNC or another RNC. If the cell belongs to another RNC, execut ency neighbour cells with same downlink frequency and uplink frequency are limited to 32.
Description Cell ID Value range: 0~65535 Content: uniquely identifying a cell Recommended value (default value): none ID of the RNC controlling a neighboring cell Value range: 0~4095 Content: uniquely identifying an RNC Neighboring cell ID Value range: 0~65535 Content: uniquely identifying a neighboring cell Recommended value (default value): none Neighboring cell oriented Cell Individual Offset (CIO) Value range: -20 ~ 20 Physical value range: -10~10,step:0.5 Physical unit: dB Content: This parameter defines the neighboring cell oriented cell individual offset. The set value functions in combination of the cell oriented CIO. Their sum is added to the measurement quantity before the UE evaluated whether an event has occurred. In handover algorithms, this parameter is used for moving the border of a cell. Recommended value (default value): 0 Flag of whether to include this neighboring relationship in the System Information Block 11 (SIB11) Value range: TRUE, FALSE Content: This parameter indicates whether the neighboring cell information is delivered in SIB11. FALSE: not to include the neighboring information in the SIB11. TRUE: to include the neighboring information in the SIB11. Recommended value (default value): TRUE
Offset of cell CPICH RSCP measurement value in cell selection or reselection when the UE is in idle mode Value range: -50~50 Physical unit: dB Content: Offset of neighboring cell CPICH measurement value. This parameter is used for RSSI measurement. The offset is subtracted from the neighboring cell measurement value before cell reselection. This parameter defines the offset of cell CPICH RSCP measurement value in cell selection or reselection when the UE is in idle mode. In cell reselection algorithm, this parameter is used for moving the border of a cell. This parameter can be configured by the network planner according to reality. NOTE: In FDD mode, this parameter is valid only when SIB11 Indicator is set as TRUE. For details, refer to 3GPP TS 25.331. As for the impact on network performance: The larger the value of the parameter, the lower the probability of selecting neighboring cells. The smaller the value the parameter, the higher the probability of doing so. Recommended value (default value): 0 Offset of cell CPICH Ec/No measurement value in cell selection or reselection when the UE is in idle mode Value range: -50~50 Physical unit: dB Content: Offset of neighboring cell CPICH measurement value This parameter is used for Ec/No measurement. The offset is subtracted from the neighboring cell measurement value before cell reselection. In cell reselection algorithm, this parameter is used for moving the border of a cell. This parameter can be configured by the network planner according to reality. NOTE: In FDD mode this parameter is valid only when SIB11 Indicator is set as TRUE. For details, refer to 3GPP TS 25.331. As for the impact on network performance: The larger the value of the parameter, the lower the probability of selecting neighboring cells. The smaller the value the parameter, the higher the probability of doing so. Recommended value (default value): 0 Flag of whether to include this neighboring relationship in the System Information Block 12 (SIB12) Value range: TRUE, FALSE Content: This parameter indicates whether the neighboring cell information is delivered in SIB12. FALSE: not to include the neighboring information in the SIB12. TRUE: to include the neighboring information in the SIB12. Recommended value (default value): FALSE Offset of cell CPICH RSCP measurement value in cell selection or reselection when the UE is in connected mode Value range: -50~50 Physical unit: dB Content: This parameter is used for cell offset in cell selection and reselection. During cell reselection, the cell offset corresponding to CPICH Ec/No is QOffset2sn, that to CPICH RSCP is QOffset1sn. Idle is used for idle mode, and Conn for connected mode. ConnQoffset1sn and ConnQoffset2sn are valid only when SIB12Ind = TRUE, namely, the SIB12 message is existing.
Offset of neighboring cell CPICH measurement value This parameter is used for RSCP measurement. The offset is subtracted from the neighboring cell measurement value before cell reselection. In cell reselection algorithm, this parameter is used for moving the border of a cell. This parameter can be configured by the Radio Network Planner(RNP) according to reality. For details, refer to 3GPP TS 25.331. As for the impact on network performance: The larger the value of the parameter, the lower the probability of selecting neighboring cells. The smaller the value the parameter, the higher the probability of doing so. Recommended value (default value): 0 Offset of cell CPICH Ec/No measurement value in cell selection or reselection when the UE is in connected mode Value range: -50~50 Physical unit: dB Content: This parameter is used for cell offset in cell selection and reselection. During cell reselection, the cell offset corresponding to CPICH Ec/No is QOffset2sn, that to CPICH RSCP is QOffset1sn. Idle is used for idle mode, and Conn for connected mode. ConnQoffset1sn and ConnQoffset2sn are valid only when SIB12Ind=TRUE, namely, the SIB12 message is existing. Offset of neighboring cell CPICH measurement value This parameter is used for Ec/No measurement. The offset is subtracted from the neighboring cell measurement value before cell reselection. In cell reselection algorithm, this parameter is used for moving the border of a cell. This parameter can be configured by the Radio Network Planner(RNP) according to reality. For details, refer to 3GPP TS 25.331. As for the impact on network performance: The larger the value of the parameter, the lower the probability of selecting neighboring cells. The smaller the value the parameter, the higher the probability of doing so. Recommended value (default value): 0 HCS cell reselection penalty timer Value range: D0, D10, D20, D30, D40, D50, D60 Content: Physical value range: 0, 10, 20, 30, 40, 50, 60 Unit: s This parameter indicates the penalty time after the HCS cell reselection. During the penalty time period, the UE cannot perform another HCS cell reselection. The larger the value of the parameter, the longer the HCS penalty time. The smaller the value of the parameter, the shorter the HCS penalty time. Recommended value (default value): D0 Offset of HCS cell CPICH RSCP measurement value in cell selection or reselection Value range: D3, D6, D9, D12, D15, D18, D21, Infinity Content: Physical value range: 3, 6, 9, 12, 15, 18, 21, Infinity Unit: dB This is the offset of cell CPICH RSCP measurement value in HCS cell selection or reselection. The larger the value of the parameter, the lower the probability of selecting neighboring cells. The smaller the value of the parameter, the higher the probability of doing so. Recommended value (default value): D3 Offset of cell CPICH Ec/No measurement value in cell selection or reselection Value range: D2, D3, D4, D6, D8, D10, D12, Infinity
Content: Physical value range: 2, 3, 4, 6, 8, 10, 12, Infinity Physical unit: dB This parameter defines the offset of cell CPICH Ec/No measurement value in cell selection or reselection. The larger the value of the parameter, the lower the probability of selecting neighboring cells. The smaller the value the parameter, the higher the probability of doing so. Recommended value (default value): D2 Priority of coverage-based inter-frequency handover Value range: 0~3 Content: "0" means that the coverage-based inter-frequency handover is not supported. "1" means the highest priority. "3" means the lowest priority. Recommended value (default value): 1 Flag of target cell for blind handovers Value range: TRUE, FALSE Content: This parameter indicates whether the neighboring cell is the target cell for blind handovers. If the value is TRUE, blind handovers can be performed to the neighboring cell. Recommended value (default value): FALSE Blind handover condition Value range: -115~-25 Physical unit: dBm Content: If the value is not -115, the handover is defined as Conditional Blind HO, which is used for the inter-frequency neighboring cells of the same coverage. If the value is -115, the handover is defined as Direct Blind HO, which is used for the inter-frequency neighboring cells of larger coverage. Recommended value (default value): -92 Priority identifier of neighboring cells Value range: TRUE, FALSE Content: TRUE indicates that the neighboring cell priority is valid in the algorithm of neighboring cell combination. FALSE indicates that the neighboring cell priority is invalid, and, in the algorithm of neighboring cell combination, the cell with invalid priority is the last one to be considered as the measurement object. Recommended value (default value): FALSE Priority of neighboring cells Value range: 0~63 Content: The priority that corresponds to the neighboring cell is valid only when the this parameter is set to TRUE. The lower the priority, the easier it is for the neighboring cell to be delivered as the measurement object. For example, it is more possible for a neighboring cell of priority 1 than a cell of priority 2 to be delivered as the Recommended value (default value): None This parameter is used as the DRD Ec/No threshold of whether to perform the blind handover. Value range: -24~0 Physical value range: -12~0,step:0.5 Physical unit: dB
Content: This parameter is used as the DRD Ec/No threshold of whether to perform the blind handover. If the Ec/No measured value of the current cell is greater than this parameter of the inter-frequency neighboring cell, this neighboring cell can be selected to be the candidate DRD cell. Recommended value: -18
e cell 1 is cell 2's. to another RNC, execute the command ADD NRNCCELL to add the information of this cell first.
INDEX
Add cell-oriented Call Admission Control (CAC) algorithm parameters. In actual operation, it is necessary to set the CAC algorithm parameters based on the network management experience and a 1. Set coverage ranges for various services: set the restrictions on the transmit power of different services to satisfy different 2. Restrict services proportions in a cell: restrict the number of different services by setting different admission thresholds for 3. Optimize resource configuration (1): set different admission thresholds for conversational service, other services and the s 4. Optimize resource configuration (2): reserve resources for UL/DL common channels so as to guarantee service transmissio There are 4 classes of services corresponding to different QoS requirements, as follows: 1. Conversational: This class corresponds to real-time services. The QoS requirement of this class is determined by people's se 2. Streaming: This class corresponds to real-time streaming services, such as audio and video programs. It's unidirectionally tr 3. Interactive: This class corresponds to data services, such as terminal browsing. It has a strict BLER requirement, and the tra 4. Background: This class also corresponds to data services. It has a strict BLER requirement, but no transmission delay requir
Note
1. [Cell environment type] is set to TU generally. In most cases, this parameter should not be changed. 2. Following restriction must be satisfied: 1)[UL OLC trigger threshold] >= [UL total power threshold] > [UL handover access threshold] > [UL threshold of Conv AMR ser 2)MAX(UL handover access threshold,UL threshold of Conv AMR service,UL threshold of Conv non_AMR service,UL threshold 3)[Ul HandOver Credit Reserved SF] >= [Ul LDR Credit SF reserved threshold]; 4)[DL OLC trigger threshold] >= [DL total power threshold] >= [DL handover access threshold] > [DL threshold of Conv AMR se 5)MAX(DL handover access threshold,DL threshold of Conv AMR service,DL threshold of Conv non_AMR service,DL threshold 6)[Dl HandOver Credit and Code Reserved SF] >= [Dl LDR Credit SF reserved threshold]; [Dl HandOver Credit and Code Reserved SF] >= [Cell LDR SF reserved threshold]; [MTCH maximal power] > [MTCH reserve power]; [MTCH maximal power SF] > [MTCH reserve SF]. 7)[Ul TotalPower CAC threshold] > [UL Target LoadFactor]. The parameters of [UL LDR trigger threshold], [DL LDR trigger threshold], [UL OLC trigger threshold] and [DL OLC trigger thres
Parameter
ID
Name
CellId
Cell ID
CellId
Cell ID
CellEnvType
UlNonCtrlThdForAMR
UlNonCtrlThdForOther
DlConvAMRThd
DlConvNonAMRThd
DlOtherThd
UL handover access
UlNonCtrlThdForHo
DlHOThd
UlCellTotalThd
DlCellTotalThd
UlCCHLoadFactor
DlCCHLoadRsrvCoeff
UlTotalEqUserNum
DlTotalEqUserNum
UlHsDpcchRsvdFactor
HsdpaStrmPBRThd
HsdpaBePBRThd
MaxHsdpaUserNum
MaxUlTxPowerforConv
MaxUlTxPowerforConv
MaxUlTxPowerforStr
MaxUlTxPowerforInt
MaxUlTxPowerforBac
BackgroundNoise
Background noise[0.1dBm]
DefPcpichEcNo
BGNSwitch
BGNSwitch
BGNAdjustTimeLen
BGNEqUserNumThd
MaxHsupaUserNum
DlHSUPARsvdFactor
DlMBMSRsvdFactor
MtchRsvPwr
MtchRsvSf
MTCH reserve SF
MtchMaxPwr
MtchMaxSf
MTCH maximal SF
UlHoCeResvSf
DlHoCeCodeResvSf
BgnStartTime
BgnEndTime
BgnUpdateThd
BgnAbnormalThd
MaxEFachUserNum
Example
Configure CAC parameters for cell 1. ADD CELLCAC: CellId=1, CellEnvType=TU, NonorthoFactor=400, UlNonCtrlThdForAMR=75, DLConvAMRThd=80, DLConvNonA
After the above operations, the parameters of cell 1 are set as follows: The cell environment type is TU; The nonorthogonality factor is 0.4; The UL threshold of Conv AMR service is 0.75; The UL threshold of Conv non_AMR service is 0.75; The UL threshold of other services is 0.6; The DL threshold of Conv AMR service is 80%; The DL threshold of Conv non_AMR service is 80%; The DL threshold of other services is 75%; The UL handover access threshold is 0.8; The DL handover access threshold is 85%; The UL common channel load factor is 0.00. The DL common channel load reserved coefficient is 0%; The UL total equivalent user number is 80; The DL total equivalent user number is 80; The UL HS-DPCCH reserve factor is 0.00; Hsdpa streaming PBR threshold is 70%; Hsdpa best effort PBR threshold is 30%; The maximum HSDPA user number is 64; The maximum UL transmit power of conversational service is 24dBm; The maximum UL transmit power of streaming service is 24dBm; The maximum UL transmit power of interactive service is 24dBm; The maximum UL transmit power of background service is 24dBm; The background noise is -103 dBm; The Default PCPICH Ec/No is -6 dB; The Auto-Adaptive Background Noise Update Switch is OFF; The Background Noise Update Continuance Time is 10 minutes; The Equivalent User Number Threshold for Background Noise Update is 0; The maximum HSUPA user number is 20; The Dl HSUPA reserved factor is 20; The Dl MBMS reserved factor is 20; Ul HandOver Credit Reserved SF is SF16; Dl HandOver Credit and Code Reserved SF is SF32.
hm parameters(ADD CELLCAC)
Control (CAC) algorithm parameters. ry to set the CAC algorithm parameters based on the network management experience and algorithm analysis results, so as to achieve the us services: set the restrictions on the transmit power of different services to satisfy different coverage requirements according to the net n a cell: restrict the number of different services by setting different admission thresholds for conversational and other services, so as to e on (1): set different admission thresholds for conversational service, other services and the services in handover state, so as to ensure the on (2): reserve resources for UL/DL common channels so as to guarantee service transmission on the common channels. orresponding to different QoS requirements, as follows: esponds to real-time services. The QoS requirement of this class is determined by people's sensory. It has a relatively looser BLER require nds to real-time streaming services, such as audio and video programs. It's unidirectionally transmitted and serves individual users. It has onds to data services, such as terminal browsing. It has a strict BLER requirement, and the transmission delay should be limited in a sensib rresponds to data services. It has a strict BLER requirement, but no transmission delay requirement. Typical services: SMS, E-mail delivery
UL total power threshold] > [UL handover access threshold] > [UL threshold of Conv AMR service], [UL threshold of Conv non_AMR servic shold,UL threshold of Conv AMR service,UL threshold of Conv non_AMR service,UL threshold of other services) > [UL LDR trigger threshol SF] >= [Ul LDR Credit SF reserved threshold]; DL total power threshold] >= [DL handover access threshold] > [DL threshold of Conv AMR service], [DL threshold of Conv non_AMR servi shold,DL threshold of Conv AMR service,DL threshold of Conv non_AMR service,DL threshold of other services) > [DL LDR trigger threshold Reserved SF] >= [Dl LDR Credit SF reserved threshold]; eserved SF] >= [Cell LDR SF reserved threshold]; H reserve power]; TCH reserve SF]. > [UL Target LoadFactor]. er threshold], [DL LDR trigger threshold], [UL OLC trigger threshold] and [DL OLC trigger threshold] are set in ADD CELLLDM and MOD CELL
Description Description:Uniquely identifying a cell. GUI value range:0~65535 Actual value range:{0~65535} Unit:None Default value:-
Recommended Value:None Description:Defining the radio environment type of the cell, such as a typical town cell, urban cell, and mountain GUI value range:TU, RA, HT Actual value range:TU, RA, HT Unit:None Default value:TU Recommended Value:TU Description:The percentage of the conversational AMR service threshold to the 100% uplink load. It is applicable to algorithm 1 and algorithm 2. The parameter is used for controlling the AMR service admission. That is, when an AMR service is accessing, the RNC evalutates the measurement value of the uplink load after the service is accessed. If the UL load of a cell is higher than this threshold after the access of an AMR speech service, this The UL load factor thresholds include parameters of [UL threshold of Conv non_AMR service], [UL handover access threshold] and [UL threshold of other services]. The four parameters can be used to limit the proportion between the conversational service, handover user and other services in a specific cell, and to guarantee the access priority of the conversational AMR service. If the value is too high the system load after admission may be GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:75 Recommended Value:75 Description:The percentage of the conversational non-AMR service threshold to the 100% uplink load. It is applicable to algorithm 1 and algorithm 2. The parameter is used for controlling the non-AMR service admission. That is, when a non-AMR service is accessing, the RNC evalutates the measurement value of the uplink load after the service is accessed. If the UL load of a cell is higher than this threshold after the access of a non-AMR speech The UL load factor thresholds include parameters of [UL threshold of Conv non_AMR service], [UL handover access threshold] and [UL threshold of other services]. The four parameters can be used to limit the proportion between the conversational service, handover user and other services in a specific cell, and to guarantee the access priority of the conversational non-AMR service. If the value is too high the system load after admission GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:75 Recommended Value:75 Description:The percentage of other service thresholds to the 100% uplink load. The services refer to other admissions except the conversational AMR service, conversational non-AMR service, and handover scenarios. It is applicable to algorithm 1 and algorithm 2. The parameter is used for controlling other service admissions. That is, when a service is accessing, the RNC evalutates the measurement value of the uplink load after the service is The UL load factor thresholds include parameters of [UL threshold of Conv non_AMR service], [UL handover access threshold] and [UL threshold of other services]. The four parameters can be used to limit the proportion between the conversational service, handover user and other services in a specific cell, and to guarantee the access priority of other services. If the value is too high the system load after admission may be over large, which GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:60 Recommended Value:60
Description:The percentage of the conversational AMR service threshold to the 100% downlink load. It is applicable to algorithm 1 and algorithm 2. The parameter is used for controlling the AMR service admission. That is, when an AMR service is accessing, the RNC evalutates the measurement value of the downlink load after the service is accessed. If the DL load of a cell is higher than this threshold after the access of an AMR speech service, The DL load factor thresholds include parameters of [DL threshold of Conv non_AMR service], [DL handover access threshold] and [DL threshold of other services]. The four parameters can be used to limit the proportion between the conversational service, handover user and other services in a specific cell, and to guarantee the access priority of the conversational AMR service. If the value is too high the system load after admission may be GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:80 Recommended Value:80 Description:The percentage of the conversational non-AMR service threshold to the 100% downlink load. It is applicable to algorithm 1 and algorithm 2. The parameter is used for controlling the non-AMR service admission. That is, when a non-AMR service is accessing, the RNC evalutates the measurement value of the downlink load after the service is accessed. If the DL load of a cell is higher than this threshold after the access of a non-AMR The DL load factor thresholds include parameters of [DL threshold of Conv non_AMR service], [DL handover access threshold] and [DL threshold of other services]. The four parameters can be used to limit the proportion between the conversational service, handover user and other services in a specific cell, and to guarantee the access priority of the conversational non-AMR service.If the value is too high the system load after admission GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:80 Recommended Value:80 Description:The percentage of other service thresholds to the 100% downlink load. The services refer to other admissions except the conversational AMR service, conversational non-AMR service, and handover scenarios. It is applicable to algorithm 1 and algorithm 2. The parameter is used for controlling other service admissions. That is, when a service is accessing, the RNC evalutates the measurement value of the downlink load after the service The DL load factor thresholds include parameters of [DL threshold of Conv non_AMR service], [DL handover access threshold] and [DL threshold of other services]. The four parameters can be used to limit the proportion between the conversational service, handover user and other services in a specific cell, and to guarantee the access priority of other services. If the value is too high the system load after admission may be over large, which GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:75 Recommended Value:75 Description:The percentage of the handover service admission threshold to the 100% uplink load. It is applicable to algorithm 1 and algorithm 2. The parameter is used for controlling the handover admission. That is, when a service is handing over to a cell, the RNC evalutates the measurement value of the uplink load after the service is accessed. If the UL load of a cell is higher than this threshold after the access, this service will be rejected. If the The UL load factor thresholds include parameters of [UL threshold of Conv non_AMR service], [UL handover access threshold] and [UL threshold of other services]. The four parameters can be used to limit the proportion between the non-handover service, handover user and other services in a specific cell, and to guarantee the access priority of the handover service. This parameter is to guarantee the access priority of the handover
GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:80 Recommended Value:80 Description:The percentage of the handover service admission threshold to the 100% downlink load. It is applicable to algorithm 1 and algorithm 2. The parameter is used for controlling the handover admission. That is, when a service is handing over to a cell, the RNC evalutates the measurement value of the downlink load after the service is accessed. If the DL load of a cell is higher than this threshold after the access, this service will be The DL load factor thresholds include parameters of [DL threshold of Conv non_AMR service], [DL handover access threshold] and [DL threshold of other services]. The four parameters can be used to limit the proportion between the non-handover service, handover user and other services in a specific cell, and to guarantee the access priority of the handover service. This parameter is related to the cell radius and cell maximum TX power. GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:85 Recommended Value:85 Description:Admission threshold of total cell uplink power. This parameter is related to the target load of the uplink schedule. The total uplink load fluctuates closing to the target load due to the schedule mechanism of the HSUPA. Therefore, the target load is added with margin, acting as the basis of this parameter. If the value is too high, the system load after admission may be over large, which impacts system stability and leads to system GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:83 Recommended Value:83 Description:Admission threshold of the total cell downlink power. If the value is too high, too many users will be admitted. However, the throughput of a single user is easy to be limited. If the value is too low, cell capacity will GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:90 Recommended Value:90 Description:The admission control decision is only for dedicated channels. For common channels, some In the UL, according to the current load factor and the characteristics of the new call, the UL CAC algorithm predicts the new traffic channels load factor with the assumption of admitting the new call, then plus with the premeditated common channel UL load factor to get the predicted UL load factor. Then, compare it with the UL admission threshold. If the value is not higher than the threshold, the call is admitted; otherwise, rejected. If the GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:0 Recommended Value:0
Description:Different admission policies are used for dedicated channel and common channel users. For common channel users, resources instead of separate power admission decision are reserved. For dedicated channel users, according to the current load factor and the characteristics of the new call, the CAC algorithm predicts the new TX power with the assumption of admitting the new call, then plus with the premeditated GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:0 Recommended Value:0 Description:When the algorithm 2 is used, this parameter defines the total equivalent user numbers corresponding to the 100% uplink load. The parameter should be related to the admission threshold and actual condition of the network. If the value is too high, the system load after admission may be over large, which GUI value range:1~200 Actual value range:1~200 Unit:None Default value:80 Recommended Value:80 Description:When the algorithm 2 is used, this parameter defines the total equivalent user number corresponding to the 100% downlink load. he parameter should be related to the admission threshold and actual condition of the network. If the value is too high, the system load after admission may be over large, which GUI value range:1~200 Actual value range:1~200 Unit:None Default value:80 Recommended Value:80 Description:Threshold of all the HSUPA user PBR whose schedule priority is lower than that of users to be admitted. If this value is too high, the possibility of rejecting HSUPA schedule services increases, which impacts access success rate. If the value is too low, too many HSUPA schedule users may be admitted, which impacts the GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:per cent Default value:100 Recommended Value:100 Description:Threshold of all the HSUPA user PBR whose schedule priority is the same as that of users to be admitted. If this value is too high, the possibility of rejecting HSUPA schedule services increases, which impacts access success rate. If the value is too low, too many HSUPA schedule users may be admitted, which impacts the GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:per cent Default value:100 Recommended Value:100 Description:Threshold of all the HSUPA user PBR whose schedule priority is higher than that of users to be admitted. If this value is too high, the possibility of rejecting HSUPA schedule services increases, which impacts access success rate. If the value is too low, too many HSUPA schedule users may be admitted, which impacts the GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:per cent
Default value:100 Recommended Value:100 Description:If the HS-DPCCH carries ACK/NACK, the system will not perform CAC. If the HS-DPCCH carries CQI, the system will perform CAC. This parameter refers to the resources reserved for the uplink HS-DPCCH carrying ACK/NACK. The corresponding threshold is the uplink limit capacity multiplied by this parameter. If the value is too high, the possibility of wrong rejection to uplink admissions increases, leading to waste in uplink resources. If GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:per cent Default value:0 Recommended Value:0 Description:Average throughput admission threshold of the HSDPA streaming service. If the sum of PBR of all the accessed streaming users is lower than the average throughput admission threshold of the HSDPA streaming service multiplied by the sum of GBR of all the accessed streaming users, it indicates that the QoS of the accessed users cannot be satisfied and new HSDPA streaming services are not allowed. Otherwise, the QoS can be satisfied and new HSDPA streaming services are allowed. If the value is too high, admission requirement of the HSDPA streaming service is strict, which improves the service quality of the HSDPA streaming service but GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:per cent Default value:70 Recommended Value:70 Description:Average throughput admission threshold of the HSDPA best effort traffic. If the sum of PBR of all the accessed HSDPA BE users is lower than the average throughput admission threshold of the HSDPA BE service multiplied by the sum of GBR of all the accessed HSDPA BE users, it indicates that the QoS of the accessed users cannot be satisfied and new HSDPA BE services are not allowed. Otherwise, the QoS can be satisfied and new HSDPA BE services are allowed. If the value is too high, admission requirement of the HSDPA BE service is strict, GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:per cent Default value:30 Recommended Value:30 Description:Maximum number of users supported by the HSDPA channel. The user in this parameter refers to the user with services on the HSDPA channel, regardless of the number of RABs carried on the HSDPA channel. Maximum HSDPA user number cannot exceed the HSDPA capability of the NodeB product, In practice, the value can be set based on the cell type and the richness of the available HSDPA power and code resources. If the value GUI value range:0~100 Actual value range:0~100 Unit:None Default value:64 Recommended Value:64 Description:Maximum UL transmit power for conversational service in a specific cell. It is based on the UL coverage requirement of the conversational service designed by the network planning.The larger the value of this parameter is, the wider the coverage of the corresponding services will be. When the downlink coverage is exceeded, the uplink coverage and downlink coverage of the service will become unbalanced. If the values of GUI value range:-50~33 Actual value range:-50~33
Unit:dBm Default value:24 Recommended Value:24 Description:Maximum UL transmit power for the streaming service in a specific cell. It is based on the UL coverage requirement of the streaming service designed by the network planning.The larger the value of this parameter is, the wider the coverage of the corresponding services will be. When the downlink coverage is exceeded, the uplink coverage and downlink coverage of the service will become unbalanced. If the values of GUI value range:-50~33 Actual value range:-50~33 Unit:dBm Default value:24 Recommended Value:24 Description:The maximum UL transmit power for the interactive service in a specific cell. It is based on the UL coverage requirement of the interactive service designed by the network planning.The larger the value of this parameter is, the wider the coverage of the corresponding services will be. When the downlink coverage is exceeded, the uplink coverage and downlink coverage of the service will become unbalanced. If the values of GUI value range:-50~33 Actual value range:-50~33 Unit:dBm Default value:24 Recommended Value:24 Description:The maximum UL transmit power for background service in a specific cell. It is based on the UL coverage requirement of the background service designed by the network planning.The larger the value of this parameter is, the wider the coverage of the corresponding services will be. When the downlink coverage is exceeded, the uplink coverage and downlink coverage of the service will become unbalanced. If the values of GUI value range:-50~33 Actual value range:-50~33 Unit:dBm Default value:24 Recommended Value:24 Description:If [Auto-Adaptive Background Noise Update Switch] is set to OFF, it is used to set background noise of the cell. If [Auto-Adaptive Background Noise Update Switch] is set to ON, new background noise is restricted GUI value range:0~621 Actual value range:-112~-50,step:0.1 Unit:dBm Default value:61 Recommended Value:61 Description:When the RNC is performing downlink open power control, it evaluates link consumption according to the PCPICH TX power and the PCPICH signal intensity detected in UE access. However, in some cases, the UE GUI value range:-30~30 Actual value range:-30~30 Unit:dB Default value:-13 Recommended Value:-13 Description:When the parameter is 'OFF', the auto-adaptive background noise update algorithm is switched off. GUI value range:OFF, ON Actual value range:OFF, ON
Unit:None Default value:ON Recommended Value:ON Description:Only when the measured background noise's duration reaches this parameter, the output of the auto-adaptive background noise update filter could be regarded as effect background noise, and the current value is replaced with the new one. At the same time, the auto-adaptive status should be restarted; otherwise, GUI value range:1~6000 Actual value range:1~6000 Unit:s Default value:120 Recommended Value:120 Description:When the number of uplink equivalent users is not larger than this parameter, the RTWP could be regarded as background noise. Therefore, the measured RTWP could be input to the auto-adaptive background noise update filter; otherwise, the RTWP could not be regarded as background noise, and should not be input to GUI value range:0~10 Actual value range:0~10 Unit:None Default value:0 Recommended Value:0 Description:Maximum number of users supported by the HSUPA channel.The user in this parameter refers to the user with services on the HSUPA channel, regardless of the number of RABs carried on the HSUPA channel. GUI value range:0~100 Actual value range:0~100 Unit:None Default value:20 Recommended Value:20 Description:Reserved DL power factor for HSUPA user. The higher the value is, the more resources reserved for the HSUPA control channel, which leads to resource waste. If the value is too low, HSUPA user quality may be GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:0 Recommended Value:0 Description:Reserved DL power factor for MBMS service. GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:0 Recommended Value:0 Description:Available guarantee power of all the MTCHs. This parameter is a protection for the MBMS PTM bearing. When the power of all the MTCHs are little, pre-emption of MBMS PTM bearing should be avoided. This is because the MBMS PTM bearing serves multiple users at the same time. The value should not be too high. GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:20 Recommended Value:20
Description:Available guarantee codes of all the MTCHs. This parameter is a protection for the MBMS PTM bearing. When the codes of all the MTCHs are few, pre-emption of MBMS PTM bearing should be avoided. This is because the MBMS PTM bearing serves multiple users at the same time. The value should not be too high. GUI value range:0~63 Actual value range:0~63 Unit:None Default value:16 Recommended Value:16 Description:Maximum power limit of all the MTCHs. This parameter is a limit to the maximum bearing of the MBMS PTM bearing. When the power of all the MTCHs are little, pre-emption of MBMS PTM bearing should be avoided. This is because the MBMS PTM bearing serves multiple users at the same time. The value should not be GUI value range:0~100 Actual value range:0~1, step:0.01 Unit:None Default value:60 Recommended Value:60 Description:Maximum code limit of all the MTCHs. This parameter is a limit to the maximum bearing of the MBMS PTM bearing. When the code of all the MTCHs are few, pre-emption of MBMS PTM bearing should be avoided. This is because the MBMS PTM bearing serves multiple users at the same time. The value should not be GUI value range:0~63 Actual value range:0~63 Unit:None Default value:40 Recommended Value:40 Description:Uplink Credit Reserved by Spread Factor for HandOver. SFOFF means that none of them are reserved for handover. If the UL spare resource cant satisfy the reserved resource after the access of a new service, the service will be rejected. If the value is too high, the credit resource reserved for handover UEs will be less, leading to the increased possibility of rejecting handover UE admissions, and performance of handover UEs GUI value range:SF4(SF4), SF8(SF8), SF16(SF16), SF32(SF32), SF64(SF64), SF128(SF128), SF256(SF256), Actual value range:SF4,SF8,SF16,SF32,SF64,SF128,SF256,SFOFF Unit:None Default value:SF16 Recommended Value:SF16 Description:Some cell resources can be reserved for handover UEs to guarantee handover success rate and improve access priority of handover services. This parameter defines the quantity of downlink code and CE resources reserved for handover. SFOFF refers to that no resources is reserved. SF32 refers to that a code resource with SF = 32 and its corresponding credit resource are reserved. The backer position the value is in {SF4,SF8,SF16,SF32,SF64,SF128,SF256,SFOFF}, the less code and credit resources reserved for handover UEs. The GUI value range:SF4(SF4), SF8(SF8), SF16(SF16), SF32(SF32), SF64(SF64), SF128(SF128), SF256(SF256), Actual value range:SF4,SF8,SF16,SF32,SF64,SF128,SF256,SFOFF Unit:None Default value:SF32 Recommended Value:SF32
Description:(1) This parameter, along with the [Algorithm stop time], is used to limit the validation time of the background noise automatic updata algorithm. If [Algorithm stop time] is greater than [Algorithm start time], and the background noise automatic updata algorithm is enabled, then the algorithm is activated during the period of [Algorithm stop time] to [Algorithm start time] each day. In other periods, the algorithm fails. If [Algorithm stop time] is less than [Algorithm start time], and the background noise automatic updata algorithm (2) Input format: HH&MM&SS. GUI value range:hour, min, sec Actual value range:hour{0~23}, min{0~59}, sec{0~59} Unit:None Default value:Recommended Value:01&00&00 Description:(1) This parameter, along with the [Algorithm start time], is used to limit the validation time of the background noise automatic updata algorithm. If [Algorithm stop time] is greater than [Algorithm start time], and the background noise automatic updata algorithm is enabled, then the algorithm is activated during the period of [Algorithm stop time] to [Algorithm start time] each day. In other periods, the algorithm fails. If [Algorithm stop time] is less than [Algorithm start time], and the background noise automatic updata algorithm (2) Input format: HH&MM&SS. GUI value range:hour, min, sec Actual value range:hour{0~23}, min{0~59}, sec{0~59} Unit:None Default value:Recommended Value:06&00&00 Description:The difference of RTWP that trigger the update of background noise. If the difference is larger than GUI value range:1~100 Actual value range:0.1~10, step:0.1 Unit:dBm Default value:5 Recommended Value:5 Description:This parameter is applied when [PARA]BGNSwitch[/PARA] is set to ON. (1) If the difference of measured background noise without filtered and the current background noise is larger than the RTWP threshold, the background noise will not be updated. (2) If the difference of new background noise and the GUI value range:1~400 Actual value range:0.1~40, step:0.1 Unit:dB Default value:100 Recommended Value:100 Description:Maximum number of users supported by the EFACH channel. GUI value range:0~48 Actual value range:0~48 Unit:None Default value:48 Recommended Value:48
r of conversational service is 24dBm; r of streaming service is 24dBm; r of interactive service is 24dBm; r of background service is 24dBm;
Noise Update Switch is OFF; ontinuance Time is 10 minutes; eshold for Background Noise Update is 0;
served SF is SF32.
ults, so as to achieve the following purposes: nts according to the network planning. Note that the coverage specification must be taken into consideration together with the capacity s other services, so as to ensure the priority of conversational service. ate, so as to ensure the handover success rate as well as the priority of conversational service.
ely looser BLER requirement, but strict transmission delay requirement. Typical services: AMR speech and video phone. individual users. It has a relatively looser delay requirement than conversational, but the sequential relation should be ensured. Typical s ld be limited in a sensible range. Typical services: Web browsing and database retrieval. es: SMS, E-mail delivery and data download.
f Conv non_AMR service] > [UL threshold of other services]; UL LDR trigger threshold] > [UL LDR release threshold];
of Conv non_AMR service]> [DL threshold of other services] ; DL LDR trigger threshold] > [DL LDR release threshold];
ELLLDM and MOD CELLLDM, and they can be listed by LST CELLLDM. The parameters of [Dl LDR Credit SF reserved threshold] and [Cell LD
SF reserved threshold] and [Cell LDR SF reserved threshold] are set in ADD CELLLDR and MOD CELLLDR, and they can be listed by LST CELLL
and they can be listed by LST CELLLDR. The parameters of [UL Target LoadFactor] is set in MOD CELLHSUPA.
INDEX
None.
Parameter
ID
Name
Modify the Constant 300 in idle mode. The maximum number ofretransmissions of RRC CONNECTION REQUEST is modified a SET IDLEMODETIMER: N300=4; After the above operation, N300 is modified as 4.
Description Value range: D100, D200, D400, D600, D800, D1000, D1200, D1400, D1600, D1800, D2000, D3000, D4000, D6000, D8000. Physical value range: 100, 200, 400, 600, 800, 1000, 1200, 1400, 1600, 1800, 2000, 3000, 4000, 6000, 8000 Physical unit: ms. Content: T300 is started when UE sends the RRC CONNECTION REQUEST message. It is stopped when UE receives the RRC CONNECTION SETUP message. RRC CONNECTION REQUEST will be resent upon the expiry of the timer if V300 is lower than or equal to N300, else enter idle mode. Recommended value: D2000. Value range: 0~7. Physical unit: None. Content: Maximum number of retransmissions of the RRC CONNECTION REQUEST message. Recommended value: 3. Physical unit: s. Content: T312 is started when UE starts to establish a DCH, and stopped when UE detects consecutive N312 "in sync" indications from L1. It indicates physical channel setup failure upon the expiry of the timer. Recommended value: 6. Value range: D1, D2, D4, D10, D20, D50, D100, D200, D400, D600, D800, D1000. Physical value range: 1, 2, 4, 10, 20, 50, 100, 200, 400, 600, 800, 1000. Physical unit: None. Content: Maximum number of successive "in sync" indications received from L1. Recommended value: D1.
fy the Constant 300 in idle mode. The maximum number ofretransmissions of RRC CONNECTION REQUEST is modified as 4. DLEMODETIMER: N300=4; the above operation, N300 is modified as 4.
odified as 4.
INDEX
It is demanded that the time value of T314 and T315 shall be both equal to 0 or both greater than T302*N302. According to 25331 CR 1990, T317 will never expire, all values are mapped to infinity.
Parameter
ID
Name
T302
Timer 302
N302
Constant 302
T304
Timer 304
N304
Constant 304
T305
Timer 305
T307
Timer 307
T308
N308
T309
Timer 309
T312
Timer 312
N312
Constant 312
T313
Timer 313
T313
Timer 313
N313
Constant 313
T314
Timer 314
T315
Timer 315
N315
Constant 315
T316
Timer 316
T316
Timer 316
T317
Example
Timer 317
Set the constant 315 used by UE in connected mode as 50. SET CONNMODETIMER: N315 = D50; After the above operation, N315 is set as 50.
ded that the time value of T314 and T315 shall be both equal to 0 or both greater than T302*N302. to 25331 CR 1990, T317 will never expire, all values are mapped to infinity.
Description Value range: D100, D200, D400, D600, D800, D1000, D1200, D1400, D1600, D1800, D2000, D3000, D4000, D6000, D8000. Physical value range: 100, 200, 400, 600, 800, 1000, 1200, 1400, 1600, 1800, 2000, 3000, 4000, 6000, 8000. Physical unit: ms. Content: T302 is started after the UE transmits the CELL UPDATE/URA UPDATE message and stopped after the UE receives the CELL UPDATE CONFIRM/URA UPDATE CONFIRM message. CELL UPDATE/URA UPDATE will be resent upon the expiry of the timer if V302 less than or equal to N302; otherwise, the UE will enter idle mode. Protocol default value is 4000. Recommended value: D2000. Value range: 0~7. Content: Maximum number of retransmissions of CELL UPDATE/URA UPDATE.Protocol default value is 3. Recommended value: 3. Physical value range: 100, 200, 400, 1000, 2000. Physical unit: ms. Content: T304 is started after the UE sends the UE CAPABILITY INFORMATION message and stopped after the UE receives the UE CAPABILITY INFORMATION CONFIRM message. UE CAPABILITY INFORMATION will be resent upon the expiry of the timer if V304 less than or equal N304; otherwise the cell update procedure will be initiated. Protocol default value is 2000. Recommended value: D2000. Value range: 0~7. Content: Maximum number of retransmissions of UE CAPABILITY INFORMATION. Protocol default value is 2. Recommended value: 3.
Value range: INFINITY, D5, D10, D30, D60, D120, D360, D720. Physical value range: Infinity, 5, 10, 30, 60, 120, 360, 720. Physical unit: min. Content: T305 is started after the UE receives CELL UPDATE CONFIRM/URA UPDATE CONFIRM in CELL_FACH, URA_PCH or CELL_PCH state. It is stopped after the UE enters another state. CELL UPDATE will be transmitted upon the expiry of this timer if T307 is not activated and the UE detects "in service area"; otherwise, T307 will be started. Protocol default value is 30. "Infinity" means the cell will not be updated. Recommended value: D10. Value range: D5, D10, D15, D20, D30, D40, D50. Physical value range: 5, 10, 15, 20, 30, 40, 50. Physical unit: s. Content: T307 is started after T305 has expired and the UE detects "out of service area". It is stopped after the UE detects "in service area". The UE will enter idle mode upon expiry.Protocol default value is 30. Value range: D40, D80, D160, D320. Physical value range: 40, 80, 160, 320. Physical unit: ms. Content: T308 is started after the UE transmits RRC CONNECTION RELEASE COMPLETE. This message will be sent upon the expiry of the Timer if V308 less than or equal to N308, otherwise, the UE will enter idle mode. Protocol default value is 160. Recommended value: D40. Value range: 1~8. Content: Maximum number of retransmission of RRC CONNECTION RELEASE COMPLETE. Recommended value: 1. Value range: 1~8. Physical unit: s. Content: T309 is started after the UE is reselected to a cell belonging to another radio access system in connected mode, or the CELL CHANGE ORDER FROM UTRAN message is received. It is stopped after the UE is successfully connected in the new cell. The UE will continue the connection to UTRAN upon expiry. Protocol default value is 5. Recommended value: 5. Value range: 1 ~ 15. Physical unit: s. Content: T312 is started after the UE starts to establish a DCH and stopped when the UE detects consecutive N312 "in sync" indications from L1. It indicates physical channel setup failure upon the expiry of the timer. Protocol default value is 1. Recommended value: 6. Value range: D1, D2, D4, D10, D20, D50, D100, D200, D400, D600, D800, D1000. Physical value range: 1, 2, 4, 10, 20, 50, 100, 200, 400, 600, 800, 1000. Content: Maximum number of successive "in sync" indications received from L1. Protocol default value is 1. Recommended value: D1. Value range: 0~15. Physical unit: s.
Content: T313 is started after the UE detects consecutive N313 "out of sync" indications from L1. T313 is stopped after the UE detects consecutive N315 "in sync" indications from L1.It indicates Radio Link (RL) failure upon expiry. Protocol default value is 3. Recommended value: 3. Value range: D1, D2, D4, D10, D20, D50, D100, D200. Physical value range: 1, 2, 4, 10, 20, 50, 100, 200. Content: Maximum number of successive "out of sync" indications received from L1. Protocol default value is 20. Recommended value: D50. Value range: D0, D2, D4, D6, D8, D12, D16, D20. Physical value range: 0, 2, 4, 6, 8, 12, 16, 20. Physical unit: s. Content: T314 is started when the criteria for radio link failure are fulfilled and only radio bearers (RBs) associated with T314 exist.T314 is stopped after the Cell Update procedure has been completed. Protocol default value is 12. In case of the RL failure when the UE is in CELL_DCH state, If the RL cannot be successfully reconfigured by CELL UPDATE CONFIRM before the expiry of the corresponding T314 (or T315), CELL UPDATE will be resent for RL reconfiguration (this operation relates to T302 and N302). T314 should be set greater than T302*N302. In case of the expiry of T314, the corresponding service RBs will be removed. Recommended value: D20. Value range: D0, D10, D30, D60, D180, D600, D1200, D1800. Physical value range: 0, 10, 30, 60, 180, 600, 1200, 1800. Physical unit: s. Content: T315 is started when the criteria for radio link failure are fulfilled, and only the radio bearer associated with T315 exists.T315 is stopped after the Cell Update procedure has been completed. Protocol default value is 180. In case of the RL failure when the UE is in CELL_DCH state, T315 (or T314) is started and CELL UPDATE is sent. If the RL cannot be successfully reconfigured by CELL UPDATE CONFIRM before the expiry of the corresponding T315 (or T314), CELL UPDATE will be resent for RL reconfiguration (this operation relates to T302 and N302). T315 should be set greater than T302*N302. In case of the expiry of T315, the corresponding service RBs will be removed. Recommended value: D30. Value range: D1, D2, D4, D10, D20, D50, D100, D200, D400, D600, D800, D1000. Physical value range: 1, 2, 4, 10, 20, 50, 100, 200, 400, 600, 800, 1000. Physical unit: NONE. Content: Maximum number of successive "in sync" indications received from L1 when T313 is activated. Protocol default value is 1. Recommended value: D1. Value range: D0, D10, D20, D30, D40, D50, INFINITY. Physical value range: 0, 10, 20, 30, 40, 50, infinity. Physical unit: s. Content: T316 is started after the UE detects "out of service area" in URA_PCH or CELL_PCH state.T316 is stopped after the UE detects "in service area".The cell update procedure will be initiated upon the expiry of the timer if "in service area" is detected; otherwise, T317 will be started. The UE will enter CELL_FACH state and initiate cell update procedure when the UE detects "in service area". Protocol default value is 30.
Recommended value: D30. Value range: D0, D10, D30, D60, D180, D600, D1200, D1800. Physical value range: infinity, infinity, infinity, infinity, infinity, infinity, infinity, infinity. Physical unit: s. Content: T317 is started after the T316 expires or the UE in CELL_FACH state detects "out of service area". According to 25331 CR 1990, T317 will never expire, all values are mapped to infinity. Protocol default value is infinity. Recommended value: D0.
nstant 315 used by UE in connected mode as 50. MODETIMER: N315 = D50; bove operation, N315 is set as 50.
INDEX
Parameter
ID
Name
2D2FMEASQUANTITY
2D2FFILTERCOEF
INTERRATFILTERCOEF
WEIGHTFORUSEDFREQ
HYSTFOR2D
2D hysteresis
HYSTFOR2F
2F hysteresis
HYSTFOR3A
3A hysteresis
HYSTFORINTERRAT
Inter-RAT hysteresis
TRIGTIME2D
TRIGTIME2D
TRIGTIME2F
TRIGTIME3A
TIMETOTRIGFORVERIFY
BSICVERIFY
INTERRATPSTHD2FECN0
INTERRATCSTHD2FRSCP
INTERRATPSTHD2FRSCP
INTERRATCOVHOCSTHD
INTERRATCOVHOPSTHD
INTERRATMEASTIME
Description Value range: Periodical_ reporting, Event_trigger. Physical unit: None. Content: Inter-RAT measurement reporting mode. "Periodical_reporting" represents periodical reporting mode. "Event_trigger" represents event-triggered reporting mode. Recommended value: Periodical_reporting. Value range: CPICH_Ec/No, CPICH_RSCP. Physical unit: None. Content: Measurement value used in coverage-based inter-RAT measurement in event (2D/2F)Ctriggered or periodical reporting mode. Recommended value: CPICH_RSCP. Value range: D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17, D19. Physical value range: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19. Physical unit: None. Content: L3 filtering coefficient for event 2D/2F measurement. The greater this parameter is, the greater the smoothing effect and the higher the anti fast fading capability, but the lower the signal change tracing capability. Recommended value: D3. Value range: D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17, D19. Physical value range: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19. Physical unit: None. Content: L3 filtering coefficient for inter-RAT measurement. The greater this parameter is, the greater the smoothing effect and the higher the anti fast fading capability, but the lower the signal change tracing capability. Recommended value: D3. Value range: 0~20. Physical value range: 0~2; step: 0.1. Physical unit: None. Content: Weight used for computing frequency general quality. The more this parameter is, the higher the calculated general quality of an active set. When this parameter is 0, the general quality of the active set is the quality of the best cell in it. This parameter is used for event 3A evaluation. Recommended value: 0. Value range: NON_PERIODIC_REPORT,D250, D500, D1000, D2000, D3000, D4000, D6000, D8000, D12000, D16000, D20000, D24000, D28000, D32000, D64000.
3RU03
Periodical_ reporting
CPICH_RSC P
D3
D3
Physical unit: ms. Content: Inter-RAT measurement reporting interval. Recommended value: D1000. Value range: 0~29. Physical value range: 0~14.5; step: 0.5. Physical unit: dB. Content: Event 2D trigger hysteresis. This parameter value is related to the slow fading characteristic. The greater this parameter is, the less the ping-pong effect and misjudgment that can be caused. However, in this case, the event cannot be triggered in time. Recommended value: 6. Value range: 0~29. Physical value range: 0~14.5; step: 0.5. Physical unit: dB. Content: Event 2F trigger hysteresis. This parameter value is related to the slow fading characteristic. The greater this parameter is, the less the ping-pong effect and misjudgment that can be caused. However, in this case, the event cannot be triggered in time. Recommended value: 6. Value range: 0~15. Physical value range: 0~7.5; step: 0.5. Physical unit: dB. Content: Event 3A trigger hysteresis. This parameter value is related to the slow fading characteristic. The greater this parameter is, the less the ping-pong effect and misjudgment that can be caused. However, in this case, the event cannot be triggered in time. Recommended value: 0. Value range: 0~15. Physical value range: 0~7.5; step: 0.5. Physical unit: dB. Content: Determining whether to trigger inter-RAT handover decision together with quality threshold. The smaller the shadow fading is, the smaller the parameter value should be. Recommended value: 4. Value range: D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D1280, D2560, D5000. Physical value range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280, 2560, 5000. Physical unit: ms.
D1000
Content: Event 2D trigger delay time. This parameter value is related to the slow fading characteristic. The greater this parameter is, the smaller the misjudgment probability, but the lower the speed of event response to measured signal changes. Recommended value: D640. Value range: D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D1280, D2560, D5000. Physical value range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280, 2560, 5000. Physical unit: ms. Content: Event 2F trigger delay time. This parameter value is related to the slow fading characteristic. The greater this parameter is, the smaller the misjudgment probability, but the lower the speed of event response to measured signal changes. Recommended value: D640. Value range: D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D1280, D2560, D5000. Physical value range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280, 2560, 5000. Physical unit: ms. Content: Event 3A trigger delay time. This parameter value is related to the slow fading characteristic. The greater this parameter is, the smaller the misjudgment probability, but the lower the speed of event response to measured signal changes. Recommended value: D640. Value range: 0~64000, 65535. Physical unit: ms. Content: Delay time for triggering a GSM cell unacknowledged by BSIC. In the period specified by this parameter, if the signal quality of an adjacent GSM cell meets the requirement for inter-RAT handover and this cell is unacknowledged, the network will start inter-RAT handover. The value 65535 means that the RNC will not hand over to an unacknowledged GSM cell. Recommended value: 65535. Value range: 0~64000. Physical unit: ms. Content: Delay time for triggering a GSM cell acknowledged by BSIC. In the period specified by this parameter, if the signal quality of an adjacent GSM cell meets the requirement for inter-RAT handover and this cell is acknowledged, the network will start inter-RAT handover. Recommended value: 0. Value range: Required, Not Required. Physical unit: None. Content: Controlling whether to report a detected cell. The value "Required" means that a detected GSM cell will be reported only after its BSIC is decoded correctly. The value "Not Required" means that a detected GSM cell will be reported whether its BSIC is decoded or not as long as it meets reporting conditions. Recommended value: Required. Value range: C24~0.
D640
D640
D640
65535
Required
Physical unit: dB. Content: If the CS service uses Ec/No as measurement item, when the measurement value is lower than this threshold, the UE reports event 2D; the RNC sends a signalling to enable compressed mode and start inter-RAT measurement. Recommended value: C16. Value range: C24~0. Physical unit: dB. Content: If the CS service uses Ec/No as measurement item, when the measurement value is higher than this threshold, the UE reports event 2F; the RNC sends a signalling to disable compressed mode and stop inter-RAT measurement. Recommended value: C14. Value range: C24~0. Physical unit: dB. Content: If the PS service uses Ec/No as measurement item, when the measurement value is lower than this threshold, the UE reports event 2D; the RNC sends a signalling to enable compressed mode and start inter-RAT measurement. Recommended value: C16. Value range: C24~0. Physical unit: dB. Content: If the PS service uses Ec/No as measurement item, when the measurement value is higher than this threshold, the UE reports event 2F; the RNC sends a signalling to disable compressed mode and stop inter-RAT measurement. Recommended value: C14. Value range: C115 to C25. Physical unit: dBm. Content: If the CS service uses RSCP as measurement item, when the measurement value is lower than this threshold, the UE reports event 2D; the RNC sends a signalling to enable compressed mode and start inter-RAT measurement. Recommended value: C95. Value range: C115 to C25. Physical unit: dBm. Content: If the CS service uses RSCP as measurement item, when the measurement value is higher than this threshold, the UE reports event 2F; the RNC sends a signalling to disable compressed mode and stop inter-RAT measurement. Recommended value: C90. Value range: C115 to C25. Physical unit: dBm. Content: If the PS service uses RSCP as measurement item, when the measurement value is lower than this threshold, the UE reports event 2D; the RNC sends a signalling to enable compressed mode and start inter-RAT measurement. Recommended value: C95.
-16
-14
-16
-14
-95
-90
-95
Value range: C115 to C25. Physical unit: dBm. Content: If the PS service uses RSCP as measurement item, when the measurement value is higher than this threshold, the UE reports event 2F; the RNC sends a signalling to disable compressed mode and stop inter-RAT measurement. Recommended value: C90. Value range: 0~63. Physical value range: C110 to C48 (1: C110; 2: C109; ...; 63: C48). Physical unit: dBm. Content: This parameter indicates the requirement of CS service inter-RAT handover for the quality of interRAT cells. If the event-triggered reporting mode is adopted, event 3A might be triggered when the quality of the target frequency is higher than this threshold. If the periodical reporting mode is adopted, this parameter is used for coverage-based inter-RAT handover evaluation at the RNC side. The value 0 means the physical value is smaller than C110 dBm. Recommended value: 21. Value range: 0~63. Physical value range: C110 to C48 (1: C110; 2: C109; ...; 63: C48). Physical unit: dBm. Content: This parameter indicates the requirement of PS service inter-RAT handover for the quality of interRAT cells. If the event-triggered reporting mode is adopted, event 3A might be triggered when the quality of the target frequency is higher than this threshold. If the periodical reporting mode is adopted, this parameter is used for coverage-based inter-RAT handover evaluation at the RNC side. The value 0 means the physical value is smaller than C110 dBm. Recommended value: 21. Value range: C24~0. Physical unit: dB. Content: If CS service inter-RAT handover uses the event-triggered reporting mode, event 3A might be triggered only the Ec/No value of the used frequency is lower than this threshold. (Event 3A can be triggered only when the two necessary conditions can be met at the same time.) Recommended value: C16. Value range: C24~0. Physical unit: dB. Content: If PS service inter-RAT handover uses the event-triggered reporting mode, event 3A might be triggered only the Ec/No value of the used frequency is lower than this threshold. (Event 3A can be triggered only when the two necessary conditions can be met at the same time.) Recommended value: C16. Value range: -115~-25. Physical unit: dBm. Content: If CS service inter-RAT handover uses the event-triggered reporting mode, event 3A might be triggered only the RSCP value of the used frequency is lower than this threshold. (Event 3A can be triggered only when the two necessary conditions can be met at the same time.)
-90
21 ( 90dBm)
21
16
16
Recommended value: C95. Value range: -115~-25. Physical unit: dBm. Content: If PS service inter-RAT handover uses the event-triggered reporting mode, event 3A might be triggered only the RSCP value of the used frequency is lower than this threshold. (Event 3A can be triggered only when the two necessary conditions can be met at the same time.) Recommended value: C95. Value range: 0~65535. Physical unit: s. Content: If the inter-RAT handover to a GSM cell fails, the possible reason is that this cell is overloaded. Therefore, in the period specified by this parameter, the system will not send the inter-RAT handover request to this cell. Recommended value: 30. Value range: 0~512. Physical unit: s. Content: If no inter-RAT handover occurs upon expiry of the inter-RAT measurement timer, the system stops inter-RAT measurement and disables the compressed mode if enabled. If this parameter is 0, the system will not start the inter-RAT measurement timer. Recommended value: 60.
95
95
30
60
INDEX
Add high speed downlink packet access (HSDPA) parameters for a cell.
Note
ID CELLID
Name Cell ID
ALLOCCODEMODE
HSPDSCHCODENUM
HSPDSCHMAXCODENUM
HSPDSCHMINCODENUM
Allocate Code Mode Code Number for HSCode Max Number for HSCode Min Number for HS-
REVSFTHD
HSSCCHCODENUM
HSDPAPOWER
HSDPAPOWER
HSPDSCHMPOCONSTENUM
Example
Add HSDPA parameters for cell 1 as follows: 1. Allocate Code Mode is Manual. 2. Number of HS_PDSCH codes is 5. 3. Number of HS_SCCH codes is 4. 4. Max sum of HS_PDSCH power and HS_SCCH power is 38 dBm. 5. HS_PDSCH MPO Constant is 2.5dB. ADD CELLHSDPA: CELLID=1,AllocCodeModeManual,HSPDSCHCODENUM=5, HSSCCHCODENUM=4, HSDPAPOWER=380,HSP
ADD CELLHSDPA)
Description Value range: 0~65535. Content: Uniquely identifying a cell. Value range: Manual,Automatic. Content: Choose the mode of allocating HsPdsch codes.There are two modes: Manual, Automatic. If Manual is chosen, allocating HsPdsch code number the equal of configured HsPdsch code number. If Automatic is chosen, allocating HsPdsch code number between configured HsPdsch Maximum code number and HsPdsch Minimum code number. Recommended value: Manual. Value range: 1~15. Content: Number of HS-PDSCH codes. Recommended value: 5. Value range: 1~15. Content: Maxmim Number of HS-PDSCH codes. Recommended value: 10. Value range: 1~15. Content: Minimum Number of HS-PDSCH codes. Recommended value: 5. Content: Reserved SF.This parameter is used to decide whether increase HsPdsch code number or not. If in cell's code tree there is at least one code can be reserved and this code's SF is equal to or less than this parameter ,try to increase HsPdsch code number. If not, try to decrease HsPdsch code number. Recommended value: SF32. Value range: 1~15. Content: Number of HS-SCCH codes. Recommended value: 4. Value range: 0~500. Physical value range: 0~50: step: 0.1.
Content: Max sum of HS_PDSCH power and HS_SCCH power. Physical unit: dBm. Recommended value: 380. Value range: -0.5dB, 0.5dB, 1.5 dB, 2.5dB, 3.5dB, 4.5dB, 5.5dB Content: Measure Power Offset Constant is used to compute Measure Power Offset. Measure Power Offset = Min(13,CellMaxPower - PcpichPower - Measure Power Offset Constant) Physical unit: dB. Recommended value: 2.5.