Professional Documents
Culture Documents
SDCCH 12704657711474 Phpapp02
SDCCH 12704657711474 Phpapp02
Kamal Hasija
Contents
Channel Concepts Call Setup
Definitions of SDCCH
Usage of SDCCH in the GSM network (BSC) Possible SDCCH Configuration SDCCH Holding Time
April 25, 2007
Kamal Hasija
Contents
SDCCH Traffic Estimations SDCCH Congestion Reasons for SDCCH congestion How to detect SDCCH congestions Preventive actions to avoid SDCCH congestions SDCCH Dimensioning
Kamal Hasija
Logical Channels
Kamal Hasija
Downlink Channel
BTS: Transmits a carrier frequency (Pure sine wave of 67.7 Khz) This Solve 2 purpose : a> Make sure that this is BCCH Carrier b> To allow the MS to synchronize to the frequency MS: After Switch on MS Scan for this channel, since it has no information to which frequency to use. FCCH carrier enables a mobile to tune its frequency to that being broadcast by the BTS.
BTS: Transmits TDMA Frame number + Base Station Identity Code (BSIC= NCC + BCC )
MS: MS decodes the BSIC if the chosen BTS is GSM Base station within a cell
LAI
Max output power allowed in the cell
Paging Channel (PCH) Downlink Channels BTS: Broadcast the paging message to indicate the Incoming Calls or Incoming SMS. Paging message also includes the MSs identity number IMSI/TMSI MS: MS listens to the PCH. If it identifies its own mobile subscriber identity number on the PCH, it will respond.
When mobile is paged , it replies on RACH requesting a signaling channel. RACH can also used if the MS wants to make a contact the NW/ Originating calls
Access Grant Channel (AGCH) Downlink channel AGCH is answer to the RACH
NW assigns a signaling channel (SDCCH) to the MS. This assignment is performed on the AGCH
Kamal Hasija
System Signaling
Call Setup
Authentication
Location Update Assignment of Traffic channels and Transmission of Short messages
Kamal Hasija
Downlink: MS receives information regarding information concerning Transmit power to use Instructions on Timing Advance
Cell Broadcast Channel (CBCH) CBCH is used in Downlink only It is used to carry Short Message Service Cell Broadcast (SMSCB) and uses the same physical channel as the SDCCH
This channel carries information at a gross rate at 13Kbit/s * * Now it is 22.8 Kbit/s with latest R9.1
Half Rate TCH (TCH/H) : This Channel carried information at a gross rate at 6.5Kbit/s* * Now it is 11.4 Kbit/s with latest R9.1 Enhance Full Rate : The speech coding in EFR is still done at 13Kbit/s, but the coding mechanism is different that is used for normal FR. EFR gives better speech quality at the same bit rate than normal FR.
Call to an MS
More..
April 25, 2007
Kamal Hasija
Hyperframe: In GSM system every TDMA frame is assigned a fixed number, which repeats itself in a time period of 3 HOURS 28 MINUTES 53 SECONDS 760 MILLISECONDS. This time period is referred to as Hyperframe. Superframe : =51x26 Multiframes. So, Duration =51x26x8x15/26=6Sec 120ms Multiframe :There are two types of multiframe. 26 TDMA Frame Multiframe :Used to carry TCH, SACCH and FACCH
Duration =26 x 8 x 15/26 =120ms 51 TDMA Frame Multiframe : Used to carry BCCH,CCCH,SDCCH and SACCH. Duration =51 x 8 x 15/26 =235.38ms
Kamal Hasija
Bursts
Normal Bursts: This burst is used to carry information on
Traffic channel SDCCH Channel Broadcast Control Channel Paging Channel :
F : One Stealing Bit:=0 Indicates 57bit packet contains user data or speech :=1 Indicates burst stolen for FACCH Signalling RxQual derived from the 26 bit midable from the TDMA frame
Bursts
Frequency Bursts:
All 148 bits(142+6) are coded with 0. The output of GMSK Modulator is a fixed frequency signal exactly 67.7 Khz above the BCCH carrier frequency. Thus the MS on receiving this fixed frequency signal fine tunes to the BCCH frequency and waits for the Sync burst to arrive after 1 TDMA Frame .i.e =15/26*8=4.615ms
1 Time slot = 156.25 bits durations (15/26 = 0.577 ms ) TB 3 ALL ZERO 142 BITS TB 3 GP 8.25
Bursts
Synchronization Bursts:
This burst is used for time synchronization of the MS
1 Time slot = 156.25 bits durations (15/26 = 0.577 ms ) TB 3 SCH DATA 39 Bits Extended Training Sequence 64 Bits SCH DATA 39 Bits TB 3 GP 8.25
39Bit x 2=78 Bits :Are decoded to arrive 25-SCH control bits and that contains the information of the NCC ,BCC & TDMA FN
64 Bits : Long training seq. of 64 Bits are identical for all BTS
Bursts
Access Bursts:
This burst is used only for initial access by the MS to the BTS which applies 2 cases : For connection setup when idle state where a CHAN_REQ message is sent using access burst For HO when MS send HND_ACC message.
1 Time slot = 156.25 bits durations (15/26 = 0.577 ms ) TB 8 SCH Sequence 41 Bits RACH Data 36 Bits TB 3 Guard Band 68.25 Bits
36Bit Contains : BSIC+CHAN_REQ or HND_ACC 41Bit Contains : Fixed bit sequence allow BTS to recognize it is Access Burst 86.25 bits GP: Long GP enables BTS to get Propagation delay information.
Bursts
Dummy Bursts:
To enable the BCCH frequency to be transmitted with a constant power level, dummy burst are inserted. This burst is transmitted on CHGR=0 when no other type of burst is to be sent. Thus it makes possible for MS to perform the power measurement on the BTS in order to determine which BTS to use for initial access or which to use for HO
CCCH is replaced by the dummy page, when there is no paging message to transmit.
1 Time slot = 156.25 bits durations (15/26 = 0.577 ms ) TB 3 Mixed Bits 58 Training Sequence 26 Mixed Bits 58 TB Guard Band 3 8.25
58Bits: Coded with pseudo random bit seq. to prevent confusion with Freq correction burst
DOWNLINK
0 1 7 0 1 7
F10 F
F11 F12-F15 F16-19 F20-23 F24 F25 F26-29 F30 F31 F32-F35 F36-F39 F40 F41 F42-F45 F46-49 F50 S BCCH CCCH CCCH F S CCCH F S CCCH CCCH F S CCCH CCCH I
F: FCCH 1 TS ( Use 4 Slots in each 51 TDMA Frame) S: SCH 1 TS ( Use 4 Slots in each 51 TDMA Frame) I: IDLE 1 TS BCCH 4 TS CCCH 4 TS (PCH or AGCH) Paging Block 51 TDMA Frame = 9 Paging Blocks TS=0 / CHGR=0
F0 F1 TS-0 R R F3 R F3 R
UPLINK
F4 R F5 R F6 R F7 R F8 R F9 F10 R R F46 F47 R R F48 R F49 R F50 R
R: RACH 1 TS
DOWNLINK
2 3 1 2 3 7
F0-F3
F4-F7
F8-F11
F12-F15
F16-F19
F20-F23 F24-F27 F28-F31 F32-F35 F36-F39 F40-F43 F44-F47 F48 F49 F50 I I I I I I
SDCCH0 SDCCH1 SDCCH2 SDCCH3 SDCCH4 SDCCH5 SDCCH6 SDCCH7 SACCH0 SACCH1 SACCH2 SACCH3 SDCCH0 SDCCH1 SDCCH2 SDCCH3 SDCCH4 SDCCH5 SDCCH6 SDCCH7 SACCH4 SACCH5 SACCH6 SACCH7
TS=2 / CHGR=0
I:
UPLINK
3 1 2 3 7
F0-F3
F4-F7
F8-F11
F12 F13 F14 F15-F18 F19-F22 F23-F26 F27-F30 F31-F34 F35-F38 F39-F42 F43-F46 F47-F50 I I I I I I SDCCH0 SDCCH1 SDCCH2 SDCCH3 SDCCH4 SDCCH5 SDCCH6 SDCCH7 SACCH0 SDCCH0 SDCCH1 SDCCH2 SDCCH3 SDCCH4 SDCCH5 SDCCH6 SDCCH7 SACCH4
I:
F0 T
F1 T
F2 T
F3 T
F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24 F25 F26 T T T T T T T T A T T T T T T T T T T T T T I
T: TCH 1 TS A: SACCH
Usage of SDCCH
The SDCCH are used in some different ways in the GSM network: Registrations: Periodic Location Updates, IMSI Attach/Detach Call Setup: Immediate Assignment -> Assignment. SMS point-to-point: SMS messages to/from MS in Idle mode. Fax Setup Optional: USSD (Unstructured Supplementary Service Data) data transfer. MS<->Network. Similar to SMS. Controlled by the MSC.
Possible Configurations
SDCCH/8 : 8 Sub channels for signaling are mapped on 1 TS, this results 1 less TCH for the cell. SDCCH/4 (Combining BCCH and SDCCH) :4 Sub channels for signaling are mapped on BCCH TS. As a result Paging capacity on BCCH is reduced by 1/3. CBCH : If CBCH is active 1 sub channel of SDCCH is replaced by 1 CBCH channel. Limitations : SDCCH/8 in a cell = Number of TRXs
CONFIGURATIONS HYD007A 1 TRX SDCCH TCH 4 7 3 7 8 6 7 6 12 6 11 6 X X X X HYD006A 2 TRX SDCCH TCH 4 15 3 15 8 14 7 14 12 14 11 14 20 13 19 13
CHGR CHBAND 0
BPC
CHANNEL
CHRATE SPV STATE ICMBAND BUSY IDLE BUSY IDLE BUSY 1,2 1,2 1,2 1,2 1,2 1,2 1,2 IDLE IDLE IDLE IDLE IDLE IDLE IDLE
4590 SDCCH-28646 SDCCH-28645 CBCH-34305 SDCCH-28644 BCCH-34797 4496 TCH-4629 4497 TCH-4630 4499 TCH-4631 4505 TCH-4654 4506 TCH-4655 4509 TCH-4661 4575 TCH-4670 FR FR FR FR FR FR FR
CHRATE SPV STATE ICMBAND CHBAND 64K FR FR FR FR FR FR FR FR 1,2 BUSY 1,2 IDLE 1,2 IDLE 1,2 IDLE 1,2 IDLE 1,2 BUSY 1,2 IDLE 1,2 IDLE NONE NONE NONE NONE NONE NONE NONE NONE
6885 TCH-1240 6886 TCH-1241 6889 TCH-1244 6890 TCH-1245 6892 TCH-1247 6894 TCH-1249 6896 TCH-1251 6898 TCH-1253
SDCCH Congestion
SDCCH congestion: All SDCCH in a cell are at the same time busy for a
period of time which leads to rejection for new MS.
Reasons : Hanging SDCCH: Are SDCCH that are hanging busy and unusable for a
long time (many minutes or indefinite). Hanging SDCCH are generally caused by SW faults.
Short Message Service(SMS) = 6.2 Sec (Vary depending the length of SMS) Fax Transmission False Access = 2.7 Sec (MOC) = 2.9 Sec (MTC) = 1.8 Sec (when Channel req is recd by system ,as SDCCH is allocated by sending Imm Ass message, and the system waits a certain time before performing disconnection.)
AC: Avg No of Location updates =1000X(1 X 3.5)/3600=0.972 mE/Sub IC : No Location updating at all =1000X(0 X 3.5)/3600=0 mE/Sub BC: 3 times the Avg no of Location updates =1000X(3 X 3.5)/3600=2.916mE/Sub
SMS: Mean Holding time No of SMS submitted =6.2 Sec =1.0 per Sub and BH
Traffic : 1000 X (1.0 X 6.2) / 3600 =1.7 mE/sub Call Setup: Mean Holding time =2.7 Sec(MOC) & 2.9 Sec(MTC) Mob Originating Traffic (Incl B Ans) =0.8 BHCA Mob Terminating Traffic (Incl B Ans) =0.4 BHCA
Congestion of TCH/TRA/RALT
Will increase CP execution time before rejecting Imm Ass. Minor increase in mean hold time expected.
Handover on SDCCH
Handover on SDCCH will in itself increase mean hold time on SDCCH. However minor increase is expected.
Congestion on Air-interface
Congestion on Air-interface leads to delay in communication to the MS. Can give timeout in BSC during Imm Ass.Increases SDCCH mean hold time with more than 2 seconds.
Congestion on A-interface
Congestion on the A-interface will lead to increased mean hold time on SDCCH. Increase is unknown.
SDCCH Dimensioning
SDCCH Dimensioning is a compromise between SDCCH blocking rate and TCH Capacity. In order to have a successful call setup there has to be an available SDCCH as well as available TCH. Basic SDCCH configuration: It is recommended to choose 1 SDCCH/8 as the basic configuration for all the cells, If LA> 2100 Erlang (500 TRX) 1 SDCCH/4 as the basic configuration for all the cells, If LA< 2100 Erlang (500 TRX)
SDCCH Dimensioning
Automatic SDCCH dimensioning: This can be done with optional Adaptive Configuration of Logical Channel feature. This feature will add extra SDCCH/8 by reconfiguring idle TCH when SDCCH load is high, and revert back to TCH if SDCCH load goes down. Manual SDCCH Dimensioning : Monitoring SDCCH / TCH Traffic in a cell SDCCH/TCH load ratio SDCCH Grade of Service:- Max allowed TCH GOS % = 2 % The rule of Thumb says: SDCCH/4 : Max. SDCCH GOS =1/2 * 2= 1 % SDCCH/8 : Max. SDCCH GOS =1/4 * 2= 0.5%
SDCCH Dimensioning
Immediate Assignment on TCH: In case of this feature on the channel administration assigns TCH for signaling instead of an SDCCH, based on 7 different channels allocation strategies (CHAPs)
TCH first strategy : Decreases the SDCCH load and enable to use SDCCH/4 in all the cells Traffic load on TCH will in this case increases substantially so this strategy is not recommended. SDCCH first strategy : SDCCH is always allocated first if available, otherwise signaling is performed on TCH.
SDCCH Dimensioning
Example : ASSUME: CELL=3TRX ,SDCCH Traffic =4 Erlang, Bcchtype=NCOMB.No CBCH GOS: SDCCH/4 = 1%, SDCCH/8 =0.5% & TCH % =2%
1> When Immediate Assignment on TCH not used Erlang B Table :To maintain 0.5 % GOS & 4 Erlang min 13 Subchannels reqd 2SDCCH/8 => TCH=(3TRX*8TS) (1BCCH)-(2SDCCH/8)=21TCHs 21TCHs with 2 % GOS => 14.04 Erlang
2> When Immediate Assignment on TCH used If we use 1SDCCH/8 only than 4 Erlangs with 8 sub channels GOS=>3 % Congested Erlang will be =4 Erlang x 3 %=0.12Erlang 1SDCCH/8 => TCH=(3TRX*8TS) (1BCCH)-(1SDCH/8)=22TCHs 22TCHs with 2 % GOS => 14.9 Erlang Actual TCH Capacity=14.9 0.12 = 14.7 Erlang TCH Capacity in the cell is increased with 0.7 Erlang
SDCCH Dimensioning
Immediate Assignment on TCH not used
SDCCH Dimensioning
Recommended SDCCH Configurations
SDCCH Dimensioning
HALF RATE CAPACITY CALCULATION Half rate will affect SDCCH dimensioning since more signaling will be reqd when no of TCH is increased. Important dimensioning factor is therefore the Half rate penetration .i.e.the % of Half rate mobile in a NW.
Example: 2 TRX Cell, Half Rate Penetration =10 %, 1 SDCCH/8 TCH/F =14 support 14 Subscriber Penetration 10% of 14 is 1.4 = 2 Subscribers (Reqd 2 Half Rate TCH/H) Total 13 TCH/F+2TCH/H = 15 TCH required Capacity : Erlang B Table: 15 TCH @ 2% GOS => 9.0096 Erlang
SDCCH Dimensioning
Max Allowed SDCCH/TCH Load Ratio (Half Rate)
SDCCH Dimensioning
Dimensioning based on STS data More accurate dimensioning is achieved by using cell statistics .i.e. STS counters SDCCH Traffic TCH Traffic SDCCH/TCH Load Ratio % SDCCH Congestion TCH Congestion SDCCH Mean Holding Time Availability of SDCCH Channels Availability of TCH Channels
Parameters
MFRMS :This parameter defines period of transmission for PAGING REQUEST messages to the same paging subgroup.
T3212 : Is the periodic registration timer ACCSTATE : Activate/Deactivate the Adaptive config of logical channel feature per cell basis CHAP :Selecting Channel Allocation profile per cell. SLEVEL: The attempt to increase the number of SDCCH/8 will take place when allocation of an SDCCH has failed due to congestion. STIME :Parameter STIME determines how long the system waits before the number of SDCCH/8 added by this function is decreased when the demand for signalling channels has returned to a low level BTDM :Implicit detach supervision should be equal or longer than T3212 in BSC. GTDM : is an extra Gurad time in minutes before the subscriber is set to detach. RLINKT: Radio link time-out This parameter defines the time before an MS disconnects a call due to failure in decoding SACCH messages. The parameter is given as number of SACCH periods (480ms).
STS Counters
CCALLS CCONGS : Call attempt counter : Congestion counter
CTRALACC : Traffic level accumulator. CNSCAN : Number of accumulations of SDCCH traffic level counter. CNDROP : Dropped connections due to Failure.
Formulas
No. of SDCCH Attempts SDCCH Congestion (%) No. of SDCCH Connections SDCCH Establishments No Congestion (%) SDCCH Time Congestion (%) SDCCH Drop (%) SDCCH Mean Holding Time (Sec.) SDCCH Traffic (Erlang) SDCCH/TCH Ratio CCALLS 100 X { CCONGS / CCALLS } CMSESTAB 100 X {CMSESTAB / (CCALLS - CCONGS)}
100 X { CTCONGS / (RPL * 60)} 100 X { CNDROP / CMSESTAB } RPL X 60 X {(CTRALACC/CNSCAN) / CMSESTAB } CTRALACC / CNSCAN (CTRALACC/CNSCAN) / ((TFTRALACC/TFNSCAN)+(THTRALACC/THNSCAN))
W-6
23.09.03
ALL SDRP>1% SER <96% CONR >0.5 % 72Cells 116Cells 97Cells 81Cells 60Cells CT Worst Cells (S) 326 NIZ001A 1989 NIZ001B 2410 CHL001A 638 BHI001A 1702 MAH002B 664 KHA001B 1084 TEN002C 1434 TIR008A 1127 AKI001A 790 BPL001B 860 TVR001C 1099 DHA001C 169 MAH002A 390 HIN001B 1865 BPL001C 270 TAD001C 1542 CHL002C 924 MAC001A 65 DHA001B 318 ADO001B 109 174 135 109 78 CELL HIN002C KAD001B GUN009B VIZ027C KAD001C HIN001B ANA001B TEN002C KAD001A VIZ023C ADO001C GOD001B SUL001A MAH002A STP001B VSP001C STP001A TVR001C RJM008B SAN001B Cells Cells Cells Cells Cells >0.5% NOC 2.37 2.35 2.19 1.91 1.72 1.59 1.42 1.4 1.33 1.32 1.32 1.31 1.3 1.23 1.05 1.03 1.01 1.01 0.98 0.98 90 602 641 267 392 183 275 372 268 183 190 372 71 104 374 135 329 258 15 134
CELL HYD001B HYD004B HYD005A HYD007B HYD012C HYD018A HYD018B HYD020B HYD025C HYD026C HYD028A HYD028C HYD030C HYD031C HYD038A HYD040A HYD040B HYD042A HYD045B HYD051C
134 127 112 25 89 NOD 633 305 359 79 432 433 653 298 481 653 413 601 373 581 327 279 522 505 1632 229
Cells Cells Cells Cells Cells >1% 1.08 1.03 1.54 1.34 6.51 1.18 1.13 1.02 1.28 1.7 1.03 1.23 1.26 1.35 1.11 1.07 1.3 1.14 1.28 1.01
CELL ADO001B ADO002B AKI001A AKI001B AKI001C AMA001A AMA001A AMA001B AMA001C AMA001C ANK001B ANN001A ANN001B ANN001C ANP001A ANP001B ANP001C AVA001A AVA001B BHI001A
Cells Cells Cells Cells Cells >1% 1.52 1.33 1.04 1.04 2.15 1.54 2.66 1.08 2.94 2.94 1.11 3.29 2.15 5.64 1.06 2.19 1.7 1.95 1.13 1.45
175 192 187 178 206 CELL HYD012C HYD117C HYD155B HYD161B HYD168A HYD058A HYD124B HYD146B HYD012A HYD093B HYD170B HYD155A HYD161C HYD089B HYD011B HYD121B HYD146C HYD145B HYD108C HYD101C
Cells Cells Cells Cells Cells < 96 % 73.35 78.45 81.57 82.57 83.77 83.99 84 86.41 86.52 86.86 87 87.29 87.59 87.82 87.85 87.97 88.01 88.23 88.49 88.71
357 378 400 382 372 CELL KOL001B JGP001C HIN002C RAJ001B VIZ020C JGP001A VJA018B CHI001C EMG001C RAZ001B NID001C CHL004C RJM007B VJA020A ONG004B ANN001A CHI003B VSP001B ANN001C VJA019B
Cells Cells Cells Cells Cells < 96 % 65.95 72.07 73.01 73.06 73.67 75.2 75.81 77.68 78.01 78.98 79.41 79.47 80.13 81.21 81.78 81.92 82.55 82.8 83.19 83.22
68 98 71 55 59 CELL HYD201A HYD176A HYD176C HYD176B HYD137C HYD168A HYD005B HYD155A HYD161B HYD137B HYD054B HYD170B HYD171B HYD168C HYD137A HYD177B HYD142A HYD053C HYD161C HYD153C
Cells Cells Cells Cells Cells >0.5% NOC 3.31 3081 3.19 2862 2.98 1695 2.3 942 1.94 559 1.75 207 1.6 725 1.39 152 1.36 138 1.3 257 1.28 386 1.27 139 1.23 323 1.22 82 1.1 129 1.05 206 1.02 147 1.01 161 1 95 0.99 191
CT (S) 1952 8177 4397 3095 1423 656 2465 403 262 993 1654 375 1219 320 346 791 701 496 147 541
LEGENDS SDCCH Drop Rate % Week Total Dropped SDCCH's SDCCH Call Success Rate % SDCCH Congestion rate %
SDCCH Congestion Counter Cong. Time in Secs (Week Tot) SDCCH Drop Rate % SDCCH Estab Success Rate % SDCCH Congestion rate %
Thank you
BTS
2>Paging Command Imsi/Tmsi+PG+TRX+CG+TN
BSC
1>Paging(LAI+IMSI/TMSI)
MSC
SDCCH
Next..
BTS
14>Setup 15>Call Confirmed 17>Channel Activation (BSC Allocated Idle TS for Traffic)
BSC
MSC
14>Setup (Req for Services I.e. Speech/Data/Fax etc) 15>Call Confirmed 16>Assignment Req (MSC send CIC to BSC)
SDCCH
18>Channel Activation Ack 19>Assignment Cmnd (BSC send message on SDCCH to MS telling to go TCH)
TCH 20>Assign Comp (MS tune to TCH and send Ind that Chan is Seized) 20>Assign Comp (MS tune to TCH and send Ind that Chan is Seized) 21>RF Chann Realease 21>RF Chann Realease Ack 22>Alert (MS Send Alert to MSC as soon as the ringing is started in MS) 23>Connect (When MS Sub Answer the Conn message sent to MSC) 24>Connect Ack 20>Assign Comp (MS tune to TCH and send Ind that Chan is Seized)
TCH 22>Alert (MS Send Alert to MSC as soon as the ringing is started in MS) TCH 23>Connect (When MS Sub Answer the Conn message sent to MSC) 24>Connect Ack
22>Alert (MS Send Alert to MSC as soon as the ringing is started in MS)
23>Connect (When MS Sub Answer the Conn message sent to MSC) 24>Connect Ack
TCH
Exit..