Professional Documents
Culture Documents
En 10222-5
En 10222-5
Fvrier 2000
Ce document est usage exclusif et non collectif des clients PERSONAL WEBPORT Toute mise en rseau, reproduction et rediffusion, sous quelque forme que ce soit, mme partielle, sont strictement interdites. This document is intended for the exclusive and non collective use of PERSONAL WEBPORT (Standards on line) customers. All network exploitation, reproduction and re-dissemination, even partial, whatever the form (harcopy or media), is strictly prohibited.
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
D EUTSCHE NORM
February 2000
EN 10222-5
Supersedes parts of DIN 17440, September 1996 edition, and DIN 17460, September 1992 edition.
National foreword
This standard has been prepared by ECISS/TC 28 Steel forgings (Secretariat: BSI, United Kingdom). The responsible German body involved in its preparation was the Normenausschuss Eisen und Stahl (Iron and Steel Standards Committee), Working Committee AA 10 Schmiedestcke and Subcommittee 06/1 Nichtrostende Sthle. This standard specifies requirements for chemical composition, mechanical properties at room (ambient), elevated and low temperatures, and the heat treatment of forgings made of martensitic, austenitic and austenitic-ferritic stainless steels, which are primarily used for pressure vessels. Additional guidance values are given for stress rupture properties of creep-resisting austenitic steels. Together with DIN EN 10222-1, DIN EN 10250-1 and DIN EN 10250-4, this standard supersedes the specifications relating to forgings laid down in DIN 17440 and DIN 17460.
EN comprises 22 pages
No part of this standard may be reproduced without the prior permission of DIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen).
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
Amendments This standard differs from DIN 17440:1996-09 and DIN 17460:1992-09 as follows: a) b) c) d) The scope is now limited to stainless steel forgings for pressure purposes (general purpose stainless steel forgings are dealt with in DIN EN 10250-1 and DIN EN 10250-4). General requirements for open die forgings are no longer covered (see DIN EN 10222-1). Steel designations from DIN 17460 have been modified, although the material numbers have been retained. The following steel grades specified in DIN 17440 and DIN 17460 are no longer covered here: all ferritic and martensitic grades and austenitic grades X2CrNi19-11 (1.4306), X6CrNiMoNb17-12-2 (1.4580), X2CrNiMo18-15-4 (1.4438) from DIN 17440 and the austenitic creep-resisting grades X3CrNiN18 11 (1.4949), X6CrNiMo17 13 (1.4919), X8CrNiNb16 13 (1.4961), X8CrNiMoNb16 16 (1.4981), X8CrNiMoVNb16 13 (1.4988), X5NiCrAlTi31 20 (1.4958) and X8NiCrAlTi32-21 (1.4959) from DIN 17460. One martensitic, four austenitic and two austenitic-ferritic steel grades have been added, and X2CrNiMoN17-13-5 (1.4439), which is no longer covered in the main body of the EN, together with three additional austenitic grades, are given in a National Annex. Specifications regarding chemical composition, mechanical properties and heat treatment have been revised.
e)
f)
Previous editions DIN 17440: 1967-01, 1972-12, 1985-07, 1996-09 DIN 17460: 1992-09
DIN EN 10222-1, Steel forgings for pressure purposes Part 1: General requirements for open die forgings DIN EN 10250-1, Open die steel forgings for general engineering purposes Part 1: General requirements DIN EN 10250-4, Open die steel forgings for general engineering purposes Part 4: Stainless steels
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
NB.1 General
This Annex describes steel grades X2CrNiMoN17-13-5 (1.4439), X1NiCrMoCu25-20-5 (1.4539), X1CrNiMoCuN20-18-7 (1.4547) and X1CrNiMoCuN25-20-7 (1.4529), which are available in Germany and are widely used there, notably for flanges.
NB.2 Status
The steel grade described in this Annex is included in the German national version of this European Standard only, with the aim of allowing its further use in that country.
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
Si max.
Mn max.
P max.
S max.
Cr
Mo
Ni
Others
1), 2)
Number 1.4439 1.4539 1.4547 1.4529 0,030 0,020 0,020 0,020 1,00 0,70 0,70 0,50 2,00 2,00 1,00 1,00 0,045 0,030 0,030 0,030 0,015 0,010 0,010 0,010 16,50 to 18,50 19,00 to 21,00 19,50 to 2050 19,00 to 21,00 4,00 to 5,00 4,00 to 5,00 6,00 to 7,00 6,00 to 7,00 12,50 to 14,50 24,00 to 26,00 17,50 to 18,50 24,00 to 26,00 0,12 to 0,22 N max. 0,15 N, 1,20 to 2,00 Cu 0,18 to 0,25 N, 0,50 to 1,00 Cu 0,15 to 1,25 N, 0,50 to 1,50 Cu
For all steel grades, the proportion of constituents that have not been added intentionally shall not exceed the following limits: 0,75 % for copper, 0,005 % for boron (see Footnote 2). Limiting the boron content to not more than 0,001 5 % reduces the tendency to hot crack.
2)
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
Rm
3)
J at 20 C*) tr, t 35 35 35 35 l 100 120 200 200 tr, t 60 90 60 90 at 196 C tr, t 42 8 Q Q Q Q Symbol
4)
min. % N/mm
2
Solution temp. C 1060 to 1140 1060 to 1140 1140 to 1200 1120 to 1180
Cooling in
5)
l 40 35 35 35
w, a w, a w, a w, a
4) 5)
l = t = tr = Q= a= o= w=
*)
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
Table NB.2: Minimum 0,2 % proof strength (Rp0,2) properties at elevated temperatures
Steel designation Name X2CrNiMoN17-13-5 X1NiCrMoCu25-20-5 X1CrNiMoCuN20-18-7 X1CrNiMoCuN25-20-7 Number 1.4439 1.4539 1.4547 1.4529 50 C 260 200 270 270 100 C 225 175 230 230 Rp0,2 min in N/mm at a temperature of 150 C 200 165 205 210 200 C 185 155 190 190 250 C 175 145 180 180 300 C 165 130 170 170 350 C 155 130 165 165 400 C 150 125 160 160 500 C 110 148 120
2
Table NB.3: Minimum 1,0 % proof strength (Rp1,0) properties at elevated temperatures
Steel designation Name X2CrNiMoN17-13-5 X1NiCrMoCu25-20-5 X1CrNiMoCuN20-18-7 X1CrNiMoCuN25-20-7 Number 1.4439 1.4539 1.4547 1.4529 50 C 290 240 310 310 100 C 255 205 270 270 Rp1.0 min in N/mm at a temperature of 150 C 230 195 245 245 200 C 210 185 225 225 250 C 200 175 212 215 300 C 190 165 200 205 350 C 180 160 195 195 400 C 175 155 190 195 500 C 140 180 150
2
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
EN 10222-5
December 1999
English version
This European Standard was approved by CEN on 1999-09-03. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom.
European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels
1999. CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national members.
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
Attention is drawn to the non-conflicting national addition requested by Germany. This addition is only to appear as a national annex to the German edition of this European Standard. *)
*)
Corrigendum from EN 10222-5:1999/AC:2000, issued by CEN and published in the DIN-Anzeiger fr technische Regeln 7/2004.
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
Annex A (informative) Reference data for stress-rupture properties Table A.1: Stress-rupture properties
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02
PERSONAL WEBPORT pour client ALSTOM POWER le 28/06/2012 12:09 DIN EN 10222-5 : 2000-02