Professional Documents
Culture Documents
Source X FRM
Source X FRM
Introduction
The circuits in this set of problems consist of independent sources, resistors and a meter. In particular, these circuits do not contain dependent sources. Each of these circuits has a seriesparallel structure that makes it possible to simplify the circuit by repeatedly Performing source transformations. Replacing series or parallel resistors by an equivalent resistor. Replacing series voltage sources by an equivalent voltage source. Replacing parallel current sources by an equivalent source source.
Each simplification is done in such a way that the voltage or current measured by the meter is not disturbed. Generally, that requires beginning the simplification at the opposite end of the circuit from the meter and then working toward the meter. Eventually, the circuit is small enough to be easily solved using Ohms and Kirchhoffs Laws. Source transformations are discussed in Section 5.3 of Introduction to Electric Circuits by R.C. Dorf and J.A Svoboda. Series resistors are discussed in Section 3.4. Parallel resistors are discussed in Section 3.5. Series voltage sources and parallel current sources are described in Section 3.6.
Worked Examples
Example 1: Consider the circuit shown in Figure 1. Find the value of the voltage measured by the voltmeter.
Solution: The voltmeter measures the voltage across the current source. (The color-coded probes of the voltmeter indicate the reference direction of the voltage measured by the voltmeter.) Figure 2 shows the circuit after the replacing the voltmeter by the equivalent open circuit and adding a label to show the voltage measured by the meter. Figures 3 through 17 illustrate the use of source transformations and equivalent resistances to simplify the circuit.
Figure 2 The circuit from Figure 1 after the replacing the voltmeter by an open circuit.
Figure 5 The circuit from Figure 4 after changing the order of parallel elements.
Figure 7 The circuit from Figure 6 after replacing parallel resistors with an equivalent resistor.
Figure 10 The circuit from Figure 9 after changing the order of series elements.
Figure 12 The circuit from Figure 11 after replacing series voltage sources with an equivalent voltage source
Figure 15 The circuit from Figure 14 after changing the order of parallel elements.
Figure 17 The circuit from Figure 16 after replacing parallel resistors with an equivalent resistor.
Figure 18 The reduced circuit. Figure 18 shows the simplified circuit after labeling the current i, of the resistor. Applying KCL at the top node of the circuit gives
8 2 i+ =2 i= A 3 3 The voltage measured by the meter, vm, is also the voltage across the resistor. Ohms law gives
2 v m = 3 = 2 V 3
Example 2: Consider the circuit shown in Figure 19. Find the value of the resistance, R.
Figure 19 The circuit considered in Example 2. Solution: The voltmeter measures the voltage across one of the current sources. Figure 20 shows the circuit after the replacing the voltmeter by the equivalent open circuit and adding a label to show the voltage measured by the meter.
Figures 21 through 24 illustrate the use of source transformations and equivalent resistances to simplify the circuit.
Figure 20 The circuit from Figure 19 after the replacing the voltmeter by an open circuit.
Figure 24 The circuit from Figure 23 after replacing series resistors with an equivalent resistor
Figure 25 shows the simplified circuit after numbering the nodes. Let v1, and v2 denote the node voltages at nodes 1 and 2 respectively. Then the node voltages are v1 = -45 V Applying KCL at node 2 gives 5 40 5 = + 4 =1 R = 5 R 15 and v2 = 5 V
Example 3: Consider the circuit shown in Figure 26. Find the value of the voltage measured by the voltmeter.
Figure 26 The circuit considered in Example 3. Solution: The voltmeter measures the voltage across the current source. (The color-coded probes of the voltmeter indicate the reference direction of the voltage measured by the voltmeter.) Figure 27 shows the circuit after the replacing the voltmeter by the equivalent open circuit and adding a label to show the voltage measured by the meter.
Figures 28 through 35 illustrate the use of source transformations and equivalent resistances to simplify the circuit.
Figure 27 The circuit from Figure 26 after the replacing the voltmeter by an open circuit.
10
11
Figure 31 The circuit from Figure 32 after replacing parallel resistors with an equivalent resistor.
12
Figure 35 The circuit from Figure 34 after replacing series resistors with an equivalent resistor.
Figure 36 shows the simplified circuit after labeling the current and voltage of the 9 resistor. Applying KVL to the loop circuit gives
9 v m 12 = 0 v m = 3 V
13
Example 4: Consider the circuit shown in Figure 37. Find the value of the voltage measured by the voltmeter.
Figure 37 The circuit considered in Example 4. Solution: The voltmeter measures the voltage across 4 resistor. (The color-coded probes of the voltmeter indicate the reference direction of the voltage measured by the voltmeter.) Figure 38 shows the circuit after the replacing the voltmeter by the equivalent open circuit and adding a label to show the voltage measured by the meter.
Figures 40 through 47 illustrate the use of source transformations and equivalent resistances to simplify the circuit.
Figure 39 The circuit from Figure 38 after the replacing the voltmeter by an open circuit.
14
Figure 42 The circuit from Figure 41 after changing the order of series elements.
Figure 44 The circuit from Figure 43 after replacing series voltage sources with an equivalent voltage source.
15
Figure 46 The circuit from Figure 45 after replacing series resistors with an equivalent resistor.
16