Professional Documents
Culture Documents
Satellite Communications
Satellite Communications
com
www.jwjobs.net
Satellite Communications
Reference book: Satellite Communications, 3rd ed. Dennis Roddy McGraw-Hill International Ed.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
1.1 Introduction
Features offered by satellite communications large areas of the earth are visible from the satellite, thus the satellite can form the star point of a communications net linking together many users simultaneously, users who may be widely separated geographically Provide communications links to remote communities Remote sensing detection of pollution, weather conditions, search and rescue operations.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
1.3 Intelsat International Telecommunications Satellite Created in 1964, now has 140 member countries, >40 investing entities Geostationary orbit orbits earth`s equitorial plane.
Atlantic ocean Region (AOR), Indian Ocean Region (IOR), Pacific Ocean Region. Latest INTELSAT IX satellites wider range of service such as internet, Direct to home TV, telemedicine, teleeducation, interactive video and multimedia
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Source: http://www.intelsat.com
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
1.4 U.S DOMSAT (Domestic Satellites) Provide various telecommunication service within a country In U.S.A all domsats in geostationary orbit Direct-to-home TV service can be classified as high power, medium power, low power
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The orbit of a near polar satellite as viewed from a point rotating with the Earth.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
in U.S.A, the National Oceanic and Atmospheric Administration (NOAA) operates a weather satellite system, geostationary operational environmental satellites (GEOS) and polar operational environmental satellites (PEOS)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
2.2 Keplers first law states that the path followed by a satellite around the primary will be an ellipse. An ellipse has two focal points shown as F1 and F2
The center of mass of the two-body system, termed the barycenter, is always centered on one of the foci
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
In our specific case, because of the enormous difference between the masses of the earth and the satellite, the center of mass coincides with the center of the earth, which is therefore always at one of the foci. The semimajor axis of the ellipse is denoted by a, and the semiminor axis, by b. The eccentricity e is given by
a 2 b2 e! a
For an elliptical orbit, 0 < e < 1. When e = 0, the orbit becomes circular.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
2.3 Kepler`s Second Law Keplers second law states that, for equal time intervals, a satellite will sweep out equal areas in its orbital plane, focused at the barycenter.
Thus the farther the satellite from earth, the longer it takes to travel a given distance
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
2.4 Keplers Third Law states that the square of the periodic time of orbit is proportional to the cube of the mean distance between the two bodies. The mean distance is equal to the semimajor axis a. For the artificial satellites orbiting the earth, Keplers third law can be written in the form
Q a ! 2 n
3
(2.2)
a = semimajor axis (meters) n = mean motion of the satellite (radians per second) Q = earths geocentric gravitational constant. = 3.986005 v 1014 m3/sec2
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Eqt (2.2) applies only to ideal situation satellite orbiting a perfectly spherical earth of uniform mass, with no pertubing forces acting, such as atmospheric drag. Section 2.8 will take account of the earth`s oblateness and atmospheric drag. With n in radians per second, the orbital period in seconds is given by
2T P! n
(2.4)
This shows that there is a fixed relationship between period and size
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Example 2.1: Calculate the radius of a circular orbit for which the period is 1day. Solution: The mean motion, in rad/ day, is Thus, Also,
2 T n :! 1day
a ! 42241km
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jwjobs.net
Descending node: The point where the orbit crosses the equatorial plane going from north to south. Line of nodes The line joining the ascending and descending nodes through the center of the earth. Inclination The angle between the orbital plane and the earths equatorial plane. It is measured at the ascending node from the equator to the orbit, going from east to north. The inclination is shown as i in Fig. 2.3.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Prograde orbit An orbit in which the satellite moves in the same direction as the earths rotation. Also known as a direct orbit. The inclination of a prograde orbit always lies between 0 and 90 Retrograde orbit An orbit in which the satellite moves in a direction counter to the earths rotation. The inclination of a retrograde orbit always lies between 90 and 180. Argument of perigee The angle from ascending node to perigee, measured in the orbital plane at the earths center, in the direction of satellite motion.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Right ascension of the ascending node: To define completely the position of the orbit in space, the position of the ascending node is specified. Mean anomaly: Mean anomaly M gives an average value of the angular position of the satellite with reference to the perigee True anomaly: The true anomaly is the angle from perigee to the satellite position, measured at the earths center. This gives the true angular position of the satellite in the orbit as a function of time.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
2.8.1 Effects of a nonspherical earth For a spherical earth of uniform mass, Keplers third law (Eq. 2.2) gives the nominal mean motion n0.
Q n0 ! a3
The 0 subscript as a reminder that this result applies for a perfectly spherical earth of uniform mass. However, earth is not perfectly spherical an equatorial bulge and a flattening at the poles (oblate spheroid)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
(2.8)
K1 = 66,063.1704 km2 a (constant). The earths oblateness has negligible effect on the semimajor axis a. The orbital period taking into account the earths oblateness is termed the anomalistic period (e. g., from perigee to perigee). The anomalistic period is
2T PA ! sec n
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
If n is known, equation 2.8 can be used to solve a, by solving the root of the following equation
1 1.5 sin 2 i
Q 1 1 n 3 !0 1.5 2 2 a 1 e
a
(2.10)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Oblateness of the earth produces two rotations on the orbital plane: 1. Regression of the nodes 2. Rotation of the line of the apsides in the orbital plane Regression of the nodes, the nodes appear to slide along the equator. The line of nodes, which is in the equatorial plane, rotates about the center of the earth. Thus ;, the right ascension of the ascending node, shifts its position. If the orbit is prograde, the nodes slide westward, if retrograde, they slide eastward. For a polar orbit (i = 90), the regression is zero.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Rotation of the line of apsides in the orbital plane, the argument of perigee changes with time.
Both effects depend on the mean motion n, the semimajor axis a, and the eccentricity e. These factors can be grouped into one factor K given by
nK 1 K! 3 a (1 e 2 ) 2
(2.11)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
(2.12)
Where i is the inclination. The rate of change of the nodes will have the same units as n. Rate of change negative If positive regression westward
regression is eastward
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
(2.13)
Units: same as n Given Epoch time = t0, right ascension of the ascending node ;0 at epoch, argument of the perigee [0 at epoch, the new values for ; and [ at time t is: d; (2.14) ; ! ;0 (t t0 )
dt d[ [ ! [0 (t t0 ) dt
www.jntuworld.com
(2.15)
www.jntuworld.com
www.jwjobs.net
2.8.2 Atmospheric Drag The effects of atmospheric drag are significant for near-earth satellites,( below about 1000 km). The drag is greatest at the perigee, which reduce the velocity at this point, thus the satellite does not reach the same apogee height on successive revolutions. The result is that the semimajor axis and the eccentricity are both reduced. Drag does not noticeably change the other orbital parameters, including perigee height. An approximate expression for the change of major axis is
n0 a $ a0 '
n n t t 0 0 0
www.jntuworld.com
2 3
(2.16)
www.jntuworld.com
www.jwjobs.net
The mean anomaly is also changed. An approximate expression for the amount by which it changes is
n0 HM ! t t0
2 2
(2.17)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
With inclined orbits the satellites are not geostationary, thus the required look angles and range will change with time. Determination of the look angles and range involves the following quantities and concepts: 1. The orbital elements, as published in the NASA bulletins and described in Sec. 2.6 2. Various measures of time 3. The perifocal coordinate system, which is based on the orbital plane 4. The geocentric-equatorial coordinate system, which is based on the earths equatorial plane 5. The topocentric-horizon coordinate system, which is based on the observers horizon plane
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The two major coordinate transformations needed are: The satellite position measured in the perifocal system is transformed to the geocentric-horizon system in which the earths rotation is measured, thus enabling the satellite position and the earth station location to be coordinated. The satellite-to-earth station position vector is transformed to the topocentric-horizon system, which enables the look angles and range to be calculated.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
2.9.1 Calendars
The mean sun does move at a uniform speed but otherwise requires the same time as the real sun to complete one orbit of the earth, this time being the tropical year. A day measured relative to this mean sun is termed a mean solar day. Calendar days are mean solar days, and generally they are just referred to as days. A tropical year contains 365.2422 days. In order to make the calendar year, also referred to as the civil year, more easily usable, it is normally divided into 365 days. The extra 0.2422 of a day is significant and for example, after 100 years, there would be a discrepancy of 24 days between the calendar year and the tropical year.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Julius Caesar made the first attempt to correct for the discrepancy by introducing the leap year, in which an extra day is added to February whenever the year number is divisible by four. This gave the Julian calendar, in which the civil year was 365.25 days on average, a reasonable approximation to the tropical year. By the year 1582, an appreciable discrepancy once again existed between the civil and tropical years. Pope Gregory XIII took matters in hand by abolishing the days October 5 through October 14, 1582, to bring the civil and tropical years into line and by placing an additional constraint on the leap year in that years ending in two zeros must be divisible by 400 to be reckoned as leap years. This dodge was used to miss out Gregorian calendar 3 days every 400 years. The resulting calendar is the, which is the one in use today.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
2.9.2 Universal Time Universal time coordinated (UTC) is the time used for all civil timekeeping purposes, and as a standard for setting clocks. The fundamental unit for UTC is the mean solar day. The mean solar day is divided into 24 hours, an hour into 60 minutes, and a minute into 60 seconds. Thus there are 86,400 clock seconds in a mean solar day.
Satellite-orbit epoch time is given in terms of UTC. Universal time coordinated is equivalent to Greenwich mean time (GMT), as well as Zulu (Z) time
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Distinction between system is not critical, the term universal time (UT) will be used. Given UT in the normal form of hours, minutes, and seconds, it is converted to fractional days as
UTday
UT o ! 360 v UTday
(2.19)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
2.9.3 Julian Dates Calendar times are expressed in UT, and although the time interval between any two events may be measured as the difference in their calendar times, the calendar time notation is not suited to computations where the timing of many events has to be computed. What is required is a reference time to which all events can be related in decimal days. Julian zero time reference is 12 noon (12: 00 UT) on January 1 in the year 4713B.C. The Julian day or Julian day number (JDN) is the (integer) number of days that have elapsed since Monday, January 1, 4713 BC in the Julian calendar. That day is counted as Julian day zero.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The Julian Date (JD) is the number of days (with decimal fraction of the day) that have elapsed since 12 noon Greenwich Mean Time (UT or TT) of that day. Rounding to the nearest integer gives the Julian day number. The Julian day number can be considered a very simple calendar, where its calendar date is just an integer. Ordinary calendar times are easily converted to Julian dates, measured on a continuous time scale of Julian days. First determine the day of the year, keeping in mind that day zero, denoted as Jan 0, is December 31. For example, noon on December 31 is denoted as Jan 0.5, and noon on January 1 is denoted as Jan 1.5
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The Julian day number can be calculated using the following formulas: The months January to December are 1 to 12. Astronomical year numbering is used, thus 1 BC is 0, 2 BC is 1, and 4713 BC is 4712. In all divisions (except for JD) the floor function is applied to the quotient (for dates since 1 March 4800 all quotients are non-negative, so we can also apply truncation).
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Example 2.10: Find the Julian day for 13h UT on 18 Dec.2000 Solution: JD = 2451897.0417 day
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Certain calculations require a time interval measured in Julian centuries. Julian century consists of 36,525 mean solar days. The time interval is reckoned from a reference time of January 0.5, 1900, which corresponds to 2,415,020 Julian days. Reference time JDref, the Julian century JC, and the time in question JD, then the interval in Julian centuries from the reference time to the time in question is given by
T!
JD JDref JC
(2.20)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Example 2.11: Find the time in Julian centuries from the reference time January 0.5 1900 to 13h UT on 18 December 2000
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
2.9.4 Sidereal time Sidereal time is time measured relative to the fixed stars. It will be seen that one complete rotation of the earth relative to the fixed stars is not a complete rotation relative to the sun.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The sidereal day is defined as one complete rotation of the earth relative to the fixed stars. One sidereal day has 24 sidereal hours, one sidereal hour has 60 sidereal minutes, and one sidereal minute has 60 sidereal seconds The relationships between the two systems, given in Bate et al. (1971), are
1 mean solar day = 1.0027379093 mean sidereal days = 24h 3m 56s .55536 sidereal time (2.21) = 86,636.55536 mean sidereal seconds 1 mean sidereal day = 0.9972695664 mean solar days = 23h 56m 04s .09054 mean solar time (2.22) = 86,164.09054 mean solar seconds
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Measurements of longitude on the earths surface require the use of sidereal time (discussed further in Sec. 2.9.7). The use of 23 h, 56 min as an approximation for the mean sidereal day will be used later in determining the height of the geostationary orbit
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
2.9.2 The orbital Plane In the orbital plane, the position vector r and the velocity vector v specify the motion of the satellite
www.jntuworld.com
www.jwjobs.net
a 1 e2 r! 1 e cos v
(2.23)
The true anomaly v is a function of time. The usual approach to determining v proceeds in two stages. First, the mean anomaly M at time t is found.
! n(t T )
(2.24)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The time of perigee passage T can be eliminated from eq. (2.24) if one is working from the elements specified by NASA. For the NASA elements:
0
! n (t 0 T )
0
Therefore,
T ! t0
(2.25)
M ! M 0 n(t t0 )
(2.26)
Consistent units must be used throughout. For example, with n in degrees/ day, time (t - t0) must be in days and M0 in degrees, and M will then be in degrees.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Once the mean anomaly M is known, the next step is to solve an equation known as Keplers equation. Keplers equation is formulated in terms of an intermediate variable E, known as the eccentric anomaly, and is usually stated as
M ! E e sin E
(2.27)
This equation requires an iterative solution, preferably by computer to solve for E as the root of the equation
M ( E e sin E ) ! 0
(2.28)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
v 1 e E tan ! tan 2 1 e 2
(2.29)
It may be noted that r, the magnitude of the radius vector, also can be obtained as a function of E and is
r ! a 1 e cos E
(2.30)
For near-circular orbits where the eccentricity is small, an approximation for v directly in terms of M is
5 2 v $ M 2e sin M e sin 2M 4
(2.31)
Note that the first M term on the right-hand side must be in radians, and v will be in radians.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Example 2.14, textbook page 45 Magnitude r of position vector r may be calculated by either equation (2.23) or (2.30).
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jwjobs.net
The position vector in this coordinate system, which will be referred to as the PQW frame, is given by
(2.32)
The perifocal system is very convenient for describing the motion of the satellite. If the earth were uniformly spherical, the perifocal coordinates would be fixed in space. However, the equatorial bulge causes rotations of the perifocal coordinate system, as described in Sec. 2.8.1. These rotations are taken into account when the satellite position is transferred from perifocal coordinates to geocentric-equatorial coordinates
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jwjobs.net
It should be kept in mind that ; and [ may be slowly varying with time, as shown by Eqs. (2.12) and (2.13). The unit vectors in this system are labeled I, J, and K, and the coordinate system is referred to as the IJK frame, with positive I pointing along the line of Aries (reference line being fixed by the stars). To transformation vector r from the PQW frame to the IJK frame:
rI ~ rp r ! R r J Q rK
(2.33a)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
(cos ; cos [ sin ; sin [ cos i ) cos ; sin [ sin ; cos [ cos i ~ R ! sin ; cos [ cos ; sin [ cos i sin ; sin [ cos ; cos [ cos i sin [ sin i cos [ sin i
This gives the components of the position vector r for the satellite, in the IJK, or inertial, frame. The angles ; and [ take into account the rotations resulting from the earths equatorial bulge, as described in Sec. 2.8.1.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
2.9.7 Earth station referred to the IJK frame The earth stations position is given by the geographic coordinates of latitude PE and longitude JE. North latitudes will be taken as positive numbers and south latitudes as negative numbers, zero latitude, is the equator. Longitudes east of the Greenwich meridian will be taken as positive numbers, and longitudes west, as negative numbers.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The position vector of the earth station relative to the IJK frame is R as shown in Fig. 2.10.
Figure 2.10 Position vector R of the earth relative to the IJK frame
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The angle between R and the equatorial plane is denoted by ]E. To find R, first find the position of the Greenwich meridian relative to the I axis as a function of time. The angular distance from the I axis to the Greenwich meridian is measured directly as Greenwich sidereal time (GST), also known as the Greenwich hour angle, or GHA. The formula for GST in degrees is
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Local sidereal time (LST) is found by adding the east longitude of the station in degrees. LST = GST + EL East longitude for the earth station will be denoted as EL. Longitude was expressed in positive degrees east and negative degrees west. For east longitudes, EL=JE, while for west longitudes, EL = 360 + JE. For example, earth station at east longitude 40 EL = 40 For an earth station at west longitude 40, EL = 360 + (-40) = 320. Thus the local sidereal time in degrees is given by LST = GST + EL
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Knowing the LST, the position vector R of the earth station can located with reference to the IJK frame. However, when R is resolved into its rectangular components, account must be taken of the oblateness of the earth. The earth may be modeled as an oblate spheroid, in which the equatorial plane is circular, and any meridional plane (i. e., any plane containing the earths polar axis) is elliptical, as illustrated in Fig. 2.11.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Figure 2.11 Reference ellipsoid for the earth showing the geocentric latitude ]E and the geodetic latitude PE
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
For the reference ellipsoid model, the semimajor axis of the ellipse is equal to the equatorial radius, the semiminor axis is equal to the polar radius, and the surface of the ellipsoid represents the mean sea level. With semimajor axis aE and semiminor axis bE gives aE = 6378.1414 km bE = 6365.755 km
The eccentricity of the earth is
aE bE eE ! ! 0.08182 aE
(2.38)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
In Figs. 2.10 and 2.11, what is known as the geocentric latitude is shown as ]E. This differs from what is normally referred to as latitude. An imaginary plumb line dropped from the earth station makes an angle PE with the equatorial plane, as shown in Fig. 2.11. This is known as the geodetic latitude, and for all practical purposes here, this can be taken as the geographic latitude of the earth station.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
With the height of the earth station above mean sea level denoted by H, the geocentric coordinates of the earth station position are given in terms of the geodetic coordinates by
N! aE 1 eE sin PE
2 2
(2.39)
(2.42)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Figure 2.12: Topocentric-horizon coordinate system (SEZ frame): (a) Overall view, (b) Detailed view
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
As shown in the previous section, the range vector V is known in the IJK frame, and it is now necessary to transform this to the SEZ frame.
V S sin] E cos LST V ! sin LST E VZ cos] E cos LST sin] E sin LST cos LST cos] E sin LST cos] E V I V 0 J sin] E VK
(2.44)
z ] E ! arctan l
(2.45)
The coordinates l and z given in Eqs. (2.40) and (2.42) are known in terms of the earth station height and latitude.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
For zero height, the angle ]E is known as the geocentric latitude and is given by
(2.46)
Difference between the geodetic and geocentric latitudes reaches a maximum at a geocentric latitude of 450, when the geodetic latitude is 45.1920 The magnitude of the range and the antenna look angles are obtained from
V ! VS VE VZ
2 2
(2.47) (2.48)
VZ V ! arcsin V
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
V ! arctan
VE VS
Then the azimuth depends on which quadrant E is in and is given by Table 2.2.
VS VS
Azimuth degrees
E
+ + -
+ + -
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
2.9.9 The subsatellite point The point on the earth vertically under the satellite is referred to as the subsatellite point. The latitude and longitude of the subsatellite point and the height of the satellite above the subsatellite point can be determined from a knowledge of the radius vector r. Figure 2.13 shows the meridian plane which cuts the subsatellite point. The height of the terrain above the reference ellipsoid at the subsatellite point is denoted by HSS, and the height of the satellite above this, by hSS.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Thus the total height of the satellite above the reference ellipsoid is
h ! H SS hSS
(2.50)
Components for the radius vector r in the IJK frame are given in equation (2.33) Figure 2.13 is similar to 2.11, with difference in r replacing R, height to the point of interest h replacing H, and subsatellite latitude shown by PSS. Thus, from equation (2.39) to (2.42) are written as,
N!
aE 1 eE sin PSS
2 2
(2.51)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
rI ! N h cos PSS cos LST rJ ! N h cos PSS sin LST rK ! N 1 eE h sin PSS
Three equations in three unknowns, LST, PE, and h. Referring to Fig. 2.10, the east longitude is obtained from Eq. (2.35) as EL = LST - GST where GST is the Greenwich sidereal time.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
3.0 The Geostationary Orbit A satellite in a geostationary orbit appears to be stationary with respect to the earth. Three conditions are required for an orbit to be geostationary:
1. The satellite must travel eastward at the same rotational speed as the earth.
If the satellite is to appear stationary it must rotate at the same speed as the earth, which is constant
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
(3.1)
The period P for the geostationary is 23 h, 56 min, 4 s mean solar time (ordinary clock time). Substituting this value along with the value for Q given by Eq. (2.3) results in
aGS ! 42164km
(3.2)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
(3.4)
www.jntuworld.com
www.jwjobs.net
In practice, a precise geostationary orbit cannot be attained because of disturbance forces in space and the effects of the earths equatorial bulge. The gravitational fields of the sun and the moon produce a shift of about 0.85 /year in inclination. The earths equatorial ellipticity causes the satellite to drift eastward along the orbit. In practice, station-keeping maneuvers have to be performed periodically to correct for these shifts
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
3.2 Antenna Look Angles The look angles for the ground station antenna are the azimuth and elevation angles required at the antenna so that it points directly at the satellite. In Sec. 2.9.8 the look angles were determined in the general case of an elliptical orbit, and there the angles had to change in order to track the satellite. With the geostationary orbit, the situation is much simpler because the satellite is stationary with respect to the earth.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The three pieces of information that are needed to determine the look angles for the geostationary orbit are 1. The earth station latitude, denoted here by PE 2. The earth station longitude, denoted here by JE 3. The longitude of the subsatellite point, denoted here by JSS (often referred to as the satellite longitude)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Latitudes north will be taken as positive angles, and latitudes south, as negative angles. Longitudes east of the Greenwich meridian will be taken as positive angles, and longitudes west, as negative angles. eg: latitude 40 S -40, longitude 35 W -35. In Chap. 2, when calculating the look angles for lowerearth-orbit (LEO) satellites, it was necessary to take into account the variation in earths radius. With the geostationary orbit, this variation has negligible effect on the look angles, and the average radius of the earth will be used, R.
R ! 6371km
(3.5)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Figure 3.1: The geometry used in determining the look angles for a geostationary satellite
ES = position of the earth station SS = subsatellite point S = the satellite d = range of the earth station to the satellite
W = angle to be determine
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
2 types of triangles involved in the geometry of Fig. 3.1: spherical triangle (Fig. 3.2a) plane triangle (Fig. 3.2b)
6 angles defining the triangles: a, b, c, A, B, C Angle a = angle between the radius to the north pole and the radius to the subsatellite point, a = 90. Angle b = between the radius to the earth station and the radius to the subsatellite point. Angle c = between the radius to the earth station and the radius to the north pole. c = 90 - PE.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Other angles A, B, and C are angles between the planes. Angle A = angle between the plane containing c and the plane containing b. Angle B = angle between the plane containing c and the plane containing a. Angle C = angle between the plane containing b and the plane containing a.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
when the earth station is west of the subsatellite point, B is negative, and when east, B is positive. When the earth station latitude is north, c is less than 90, and when south, c is greater than 90.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Special rules, known as Napiers rules, are used to solve the spherical triangle. Napiers rules gives angle b and angle a as
b ! arccoscos B cos PE
sin B A ! arcsin sin b
(3.9) (3.10)
Two values will satisfy Eq. (3.10), A and 180 - A, and these must be determined by inspection. These are shown in Fig. 3.3
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Fig. 3.3 a: angle A is acute (less than 90), and the azimuth angle Az = A.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Fig. 3.3 c: angle Ac is obtuse and is given by Ac = 180 - A, where A is the acute value obtained from Eq. (3.10). By inspection, Az = Ac = 180- A
In Fig. 3.3 d, angle Ad is obtuse and is given by 180- A, where A is the acute value obtained from Eq. (3.9). By inspection, Az = 360 - Ad = 180+ A.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Applying the cosine rule for plane triangles to the triangle of Fig.3.2 b, d is approximated to:
Applying the sine rule for plane triangles to the triangle of Fig. 3.2 b, the angle of elevation is
(3.12)
www.jntuworld.com
www.jwjobs.net
3.3 Polar Mount Antenna polar mount is a piece of equipment installed into geostationary satellites to be accessed by swinging the satellite dish around one axis. This allows one positioner only to be used to remotely point the antenna at any satellite. The dish is mounted on an axis termed the polar axis such that the antenna boresight is normal to this axis, as shown in Fig. 3.5 a
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The angle between the polar mount and the local horizontal plane is set equal to the earth station latitude, PE. Thus the boresight is parallel to the equatorial plane.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Next, the dish is tilted at an angle H relative to the polar mount until the boresight is pointing at a satellite position.
Figure 3.5(b)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Where El0 = angle of elevation required for the satellite position due south of the earth station. For due south situation, angle B in eq. (3.8) equals zero, thus from eq. (3.9),
b ! PE
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Figure 3.5(c)
Combining Eqs. (3.13) and (3.14) gives the required angle of tilt as:
a H ! 90Q arccos GSO sin PE PE d
www.jntuworld.com
(3.15)
www.jntuworld.com
www.jwjobs.net
To calculate d, assume earth station altitude can be ignored (as eq. 3.11) and R = 6371km. The value H is sufficiently accurate for initial alignment. Fine adjustment can be made if necessary.
Example 3.3: Determine the angle of tilt required for a polar mount used with an earth station at latitude 49 degrees north. Assume a spherical earth of mean radius 6371 km, and ignore earth station altitude. Solution: Given data PE = 49S, aGSO= 42164km, R = 6371km
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Example 3.3: Determine the angle of tilt required for a polar mount used with an earth station at latitude 49 degrees north. Assume a spherical earth of mean radius 6371 km, and ignore earth station altitude. Solution: Given data PE = 49S, aGSO= 42164km, R = 6371km
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
3.4 Limits of Visibility There will be east and west limits on the geostationary arc visible from any given earth station. The limits will be set by the geographic coordinates of the earth station and the antenna elevation. The lowest elevation in theory is zero, when the antenna is pointing along the horizontal. To estimate of the longitudinal limits, consider an earth station at the equator, with the antenna pointing either west or east along the horizontal, as shown in Fig. 3.6.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
3.5 Near Geostationary Orbits A number of perturbing forces causes an orbit to depart from the ideal keplerian orbit. For the geostationary case, the forces are mainly due to: gravitational fields of the moon and the sun nonspherical shape of the earth. Other significant forces are solar radiation pressure and reaction of the satellite itself to motor movement within the satellite. As a result, station keeping maneuvers must be carried out to maintain the satellite within set limits of its nominal geostationary position.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Exact geostationary orbit is not attainable in practice, and orbital parameters vary with time. The two-line orbital elements are published at regular intervals, Fig. 3.7 showing typical values. The period for a geostationary satellite is 23 h, 56 min, 4 s, or 86,164 s. The reciprocal of this is 1.00273896 rev/ day, which is about the value tabulated for most of the satellites in Fig. 3.7.
www.jntuworld.com
www.jwjobs.net
Thus these satellites are geosynchronous, in that they rotate in synchronism with the rotation of the earth. However, they are not geostationary. The term geosynchronous satellite is used in many cases instead of geostationary to describe these near-geostationary satellites. However, in general a geosynchronous satellite does not have to be near-geostationary. There are a number of geosynchronous satellites that are in highly elliptical orbits with comparatively large inclinations (e. g., the Tundra satellites).
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Chapter 4: Radio Wave Propagation 4.1 Introduction A signal traveling between an earth station and a satellite must pass through the earths atmosphere, including the ionosphere. This introduce certain impairments, summarized in Table 4.1. (Refer text book, page 93)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
4.2 Atmospheric Losses Losses occur in the earths atmosphere as a result of energy absorption by the atmospheric gases. These losses are treated quite separately from those which result from adverse weather conditions, which of course are also atmospheric losses. To distinguish between these, the weather-related losses are referred to as atmospheric attenuation and the absorption losses simply as atmospheric absorption. The atmospheric absorption loss varies with frequency, as shown in Fig. 4.2. (Refer text book, page 94)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Two absorption peaks will be observed: 1. at a frequency of 22.3 GHz, resulting from resonance absorption in water vapor (H2O), and 2. at 60 GHz, resulting from resonance absorption in oxygen (O2). At other frequencies, the absorption is quite low.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
4.3 Ionospheric Effects Radio waves traveling between satellites and earth stations must pass through the ionosphere. The ionosphere has been ionized, mainly by solar radiation. The free electrons in the ionosphere are not uniformly distributed but form in layers. Clouds of electrons may travel through the ionosphere and give rise to fluctuations in the signal. The effects include scintillation, absorption, variation in the direction of arrival, propagation delay, dispersion, frequency change, and polarization rotation.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
All these effects decrease as frequency increases. Only the polarization rotation and scintillation effects are of major concern for satellite communications. Ionospheric scintillations are variations in the amplitude, phase, polarization, or angle of arrival of radio waves. Caused by irregularities in the ionosphere which changes with time. Effect of scintillations is fading of the signal. Severe fades may last up to several minutes.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Polarization rotation: porduce rotation of the polarization of a signal (Faraday rotation) When linearly polarized wave traverses in the ionosphere, free electrons in the ionosphere are sets in motion a force is experienced, which shift the polarization of the wave. Inversely proportional to frequency squared. not a problem for frequencies above 10 GHz.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
4.4 Rain Attenuation Rain attenuation is a function of rain rate. Rain rate, Rp = the rate at which rainwater would accumulate in a rain gauge situated at the ground in the region of interest (e. g., at an earth station). The rain rate is measured in millimeters per hour. Of interest is the percentage of time that specified values are exceeded. The time percentage is usually that of a year; for example, a rain rate of 0.001 percent means that the rain rate would be exceeded for 0.001 percent of a year, or about 5.3 min during any one year.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
(4.2)
where a and b depend on frequency and polarization. Values for a and b are available in tabular form in a number of publications. (eg, Table 4.2, pg 95) Once the specific attenuation is found, the total attenuation is determined as: A ! EL dB where, L = effective path length of the signal through the rain.
www.jntuworld.com
(4.3)
www.jntuworld.com
www.jwjobs.net
Because the rain density is unlikely to be uniform over the actual path length, an effective path length must be used rather than the actual (geometric) length. Figure 4.3 shows the geometry of the situation.
www.jntuworld.com
www.jwjobs.net
The geometric, or slant, path length is shown as LS. This depends on the antenna angle of elevation U and the rain height hR, which is the height at which freezing occurs. Figure 4.4 shows curves for hR for different climatic zones.
Method 1: maritime climates Method 2: Tropical climates Method 3: continental climates
Figure 4.4: Rain height as a function of earth station latitude for different climatic zones
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
For small angles of elevation (El < 10), the determination of LS is complicated by earth curvature. For El u 10, a flat earth approximation may be used. From Fig. 4.3 it is seen that
hR ho LS ! sin El
(4.4)
where rp is a reduction factor which is a function of the percentage time p and LG, the horizontal projection of LS.
Refer Table 4.3, page 97, for values of reduction factors, rp
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Putting all the factors into one equation, we obtain the rain attenuation (decibels) as:
Ap ! aR p LS rp dB
b
(4.7)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Chapter 12: The Space Link 12.1 Introduction This chapter describes how the link-power budget calculations are made. These calculations basically relate two quantities, the transmit power and the receive power, and show in detail how the difference between these two powers is accounted for. Link budget calculations are usually made using decibel or decilog quantities. These are explained in App. G.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.2 Equivalent Isotropic Radiated Power A key parameter in link budget calculations is the equivalent isotropic radiated power, conventionally denoted as EIRP. The Maximum power flux density at some distance r from a transmitting antenna of gain G is ]M
GPS ! 4Tr 2
(12.1)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
An isotropic radiator with an input power equal to GPS would produce the same flux density. Hence this product is referred to as the equivalent isotropic radiated power, or EIRP ! GPS
(12.2)
EIRP is often expressed in decibels relative to one watt, or dBW. Let PS be in watts; then
(12.3)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The isotropic gain for a paraboloidal antenna is G !L 10.472 fD
Where, f D is the carrier frequency is the reflector diameter in m
2
(12.4)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.3 Transmission Losses The [EIRP] is the power input to one end of the transmission link, and the problem is to find the power received at the other end. Losses will occur along the way, some of which are constant. Other losses can only be estimated from statistical data, and some of these are dependent on weather conditions, especially on rainfall.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The first step in the calculations is to determine the losses for clear weather, or clear-sky, conditions. These calculations take into account the losses, including those calculated on a statistical basis, which do not vary significantly with time. Losses which are weather-related, and other losses which fluctuate with time, are then allowed for by introducing appropriate fade margins into the transmission equation.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.3.1 Free Space Transmission Spreading of the signal is space causes power loss. The power flux density at the receiving antenna is ]M E IR P ! 4Tr 2
(12.6)
The power delivered to a matched receiver is this power flux density multiplied by the effective aperture of the receiving antenna. The received power is therefore:
PR ! ] M Aeff
EIRP P GR ! 4Tr 2 4T
P ! ( EIRP)(GR ) 4Tr
(12.7)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
where r = distance, or range, between the transmit and receive antennas GR = isotropic power gain of the receiving antenna. The subscript R is used to identify the receiving antenna. In decibel notation, equation (12.7) becomes 4Tr ?PR A! ?EIRPA ?GR A 10 log P Free space loss is given by 4Tr ?FSLA! 10 log P
2 2
(12.8)
(12.9) (12.10)
www.jntuworld.com
www.jwjobs.net
(12.8)
The received power [PR] will be in dBW when the [EIRP] is in dBW and [FSL] in dB. Equation (12.9) is applicable to both the uplink and the downlink of a satellite circuit
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.3.2 Feeder Losses Losses occur in the connection between the receive antenna and the receiver proper, such as in the connecting waveguides, filters, and couplers. These will be denoted by RFL, or [RFL] dB, for receiver feeder losses. The [RFL] values are added to [FSL] in Eq. (12.11). Similar losses occur in the filters, couplers, and waveguides connecting the transmit antenna to the high-power amplifier (HPA) output. However, provided that the EIRP is stated, Eq. (12.11) can be used without knowing the transmitter feeder losses. These are needed only when it is desired to relate EIRP to the HPA output
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.3.3 Antenna misalignment losses When a satellite link is established, the ideal situation is to have the earth station and satellite antennas aligned for maximum gain, as shown in Fig. 12.1 a.
Figure 12.1: (a) aligned for maximum gain, (b) earth-station antenna misaligned
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
There are two possible sources of off-axis loss, one at the satellite and one at the earth station. The off-axis loss at the earth station is referred to as the antenna pointing loss, which are usually only a few tenths of a decibel. Losses may also result at the antenna from misalignment of the polarization direction. The polarization misalignment losses are usually small, and is assumed that the antenna misalignment losses, denoted by [AML], include both pointing and polarization losses resulting from antenna misalignment.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Antenna misalignment losses have to be estimated from statistical data, based on the errors actually observed for a large number of earth stations. Separate antenna misalignment losses for the uplink and the downlink must be taken into account.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.3.4 Fixed atmospheric and ionospheric losses Atmospheric gases result in losses by absorption. These losses usually amount to a fraction of a decibel, and decibel value will be denoted by [AA]. Table 12.1 shows values of atmospheric absorption losses and Satellite pointing loss in Canada.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
?L
(12.12)
(12.13)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
[EIRP] = equivalent isotropic radiated power, dBW [FSL] = free-space spreading loss, dB [RFL] = receiver feeder loss, dB [AML] = antenna misalignment loss, dB [AA] [PL] = atmospheric absorption loss, dB = polarization mismatch loss, dB
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.5 System Noise The major source of electrical noise in equipment is from the random thermal motion of electrons in various resistive and active devices in the receiver. Thermal noise is also generated in the lossy components of antennas, and thermal-like noise is picked up by the antennas as radiation. The available noise power from a thermal noise source is given by
PN ! kTN BN
(12.14)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
where TN = equivalent noise temperature (K) BN = equivalent noise bandwidth (Hz) k = 1.38x10-23 (Boltzmanns constant) For thermal noise, noise power per unit bandwidth, N0, is constant (a.k.a noise energy) PN ! kTN joules N0 ! BN
(12.14)
In addition to thermal noise, intermodulation distortion in high-power amplifiers result in signal products which appear as noise, that is intermodulation noise.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.5.1 Antenna Noise Antennas operating in the receiving mode introduce noise into the satellite circuit.
2 groups of antenna noise: Noise originating from antenna losses Sky noise
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Sky noise: The microwave radiation which is present through out the universe and which appears to originate from matter of any form at finite temperatures. Fig.12.2 shows the equivalent noise temperature of the sky, as seen by an earth-station antenna. The lower graph: Antenna pointing directly overhead The upper graph: Antenna pointing just above the horizon. The equivalent noise temperature for satellite antennas is approx. 290 K
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The increased noise in antenna pointing overhead is due to thermal radiation of the earth. Sets limits of elevation angle to 5r for C band and 10r for Ku band.
Antenna pointing just above the horizon
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.5.2 Amplifier noise temperature Consider the noise representation of the antenna and the low noise amplifier (LNA) in Fig.12.4 below
Fig. 12.4: Circuit used in finding the equivalent noise temperature of (a) an amplifier and (b) two amplifiers in cascade
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
N 0,ant ! kTant
Where, N0,ant = Input noise energy from the antenna (Joules). In noise power per unit bandwidth Tant k = Antenna noise temperature = Boltzman constant,
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
N 0,out ! Gk Tant Te
Where, N0,out = Output noise energy Te Tant k G = Equivalent noise temperature of amplifier, referred to the input = Antenna noise temperature = Boltzman constant = Amplifier gain
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
N 0,in ! k Tant Te
12.5.3 Amplifiers in cascade The cascade connection is shown in Fig 12.4b For this, the overall gain is
G ! G1G2
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Cascaded amplifiers
The noise energy of amplifier 2 referred to its own input The noise input to amplifier 2 from the preceding stages is
www.jntuworld.com
www.jwjobs.net
This noise energy may be referred to amplifier 1 input by dividing by the available power gain of amplifier 1
N 0,1 !
N 0, 2
(12.21) G1 Te 2 ! k T T 1 a n t e G 1
N 0,1 ! kTS
TS is given by,
(12.22)
TS ! Tant
Te 2 Te1 G1
(12.23)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
From equation 12.23, the noise temperature of the second stage is divided by the power gain of the first stage when referred to the input To keep the overall noise as low as possible the first stage (usually LNA) should have high power gain as well as low noise temperature For any number of stages in cascade,
TS ! Tant
(12.24)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.5.4 Noise Factor Noise Factor, an alternative way of representing amplifier noise. Source is taken at room temperature, T0 = 290K. Input noise is kT0, output noise of the amplifier is,
N 0,out ! FGkT0
where, G = available power gain of the amplifier F = noise factor
www.jntuworld.com
(12.25)
www.jntuworld.com
www.jwjobs.net
Let Te be the noise temperature of the amplifier, and let the source be at room temperature, T0, that is T0 = Tant. With the same noise output, we obtain,
Gk T0 Te
! FGkT0
or
Te ! F 1 T0
(12.26)
(12.27)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
An absorptive network is one which contains resistive elements. It introduces losses by absorbing energy from the signal and converting it to heat (thermal noise). Consider an absorptive network with power loss L. Power loss, L = input power/output power > 1
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Referring to Fig.12.5. Let the network be matched at both ends, to a terminating resistor RT at one end and an antenna at the other. Let the system be at ambient temperature Tx. The noise energy transferred from RT in the the network is kTx. Let the network noise be represented at the output terminals by an equivalent noise temperature TNW0. Then the noise energy radiated by the antenna is
N rad
kTx ! kTNW , 0 L
(12.28)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Because the antenna is matched to a resistive source at temperature Tx, the available noise energy which is fed into the antenna and radiated is Nrad = kTx The expression for Nrad can be substituted to eq.(12.28) to give the equivalent noise temperature of the network referred to the output terminals of the network
TNW , 0
1 ! Tx 1 L
(12.29)
The equivalent noise temperature of the output can be transferred to the input on dividing by the network power gain, 1/L
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The equivalent noise temperature of the network referred to the network input is
TNW ,i ! Tx L 1
(12.30)
Since network is bilateral, eq.(12.29) and (12.30) apply for signal flow in either direction. Thus eq.(12.30) gives the equivalent noise temperature of a lossy network referred to the input at the antenna when the antenna is used in receiving mode. If lossy network is at room temperature, Tx = T0. Comparing eq.(12.26) and (12.30) shows that
F!L
www.jntuworld.com
(12.31)
www.jntuworld.com
www.jwjobs.net
12.5.6 Overall system noise temperature Refer to Fig.12.6a of a typical receiving system. The system noise temperature referred to the input is
TS ! Tant Te1
L 1
T0 LF 1
T0
G1 G1
(12.32)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Example 12.7 For the system shown in Fig12.6a, the receiver noise figure is 12dB, the cable loss is 5dB, the LNA gain is 50dB, and its noise temperature 150K. The antenna noise temperature is 35K. Calculate the noise temperature referred to the input.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
L ! 100.5 ! 3.16
G ! 105
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Example 12.8 Repeat the calculation when the system of Fig.12.6a is arranged as shown in Fig.12.6b. Solution: The cable now precedes the LNA, the equivalent noise temperature referred to the cable input is
3.16 v 15.85 1
v 290 TS ! 35 3.16 1
v 290 3.16 v150 105 ! 1136 K
Ex.12.7 and 12.8 shows why it is important that the LNA (an amplifier) be placed ahead of the cable.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.6 Carrier-to-Noise Ratio A measure of the performance of a satellite link is the ratio of carrier power to noise power at the receiver input. Conventionally, the ratio is denoted by C/ N (or CNR), which is equivalent to PR/PN. In terms of decibels, C N ! ?PR A ?PN A
(12.33)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Equations (12.17) and (12.18) may be used for [PR] and [PN], resulting in
C ! ?EIRP A ? GR A ?LOSSES A ?k A ? TS A ?BN A (12.33) N
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
therefore
C C ! ?BN A N0 N
(12.37)
[C/N] is a true power ratio in units of decibels, and [BN] is in decibels relative to one hertz, or dBHz. Thus the units for [C/No] are dBHz.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Ex.12.9: In a link-budget calculation at 12GHz, the free space loss is 206dB, the antenna pointing loss is 1dB, and the atmospheric absorption is 2dB. The receiver feeder losses are 1dB. The EIRP is 48dBW. Calculate the carrier-to-noise spectral density ratio Solution: Data are computed in tabular form, with losses entered as negative numbers. Also, recall that
?k A! 228.6 decilogs
thus
?k A! 228.6 decilogs
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The final result, 86.1 dBHz is the algebraic sum of the quantities given.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.7 The Uplink The uplink earth station is transmitting the signal and the satellite is receiving it. Equation (12.38) can be applied to the uplink, but with subscript U denotes that the uplink is being considered.
C G kA ?LOSSES A U U ? ! ?EIRP A T U N 0 U
(12.39)
Eq (12.39) contains: the earth station EIRP, the satellite receiver feeder losses, and satellite receiver G/T. The freespace loss and other losses which are frequency-dependent are calculated for the uplink frequency. The resulting carrier-to-noise density ratio given by Eq. (12.39) is that which appears at the satellite receiver.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.7.1 Saturation Flux Density TWTA The traveling-wave tube amplifiers (TWTA) are widely used in transponders to provide the final output power required to the transmit antenna.
Advantage of TWTA compared to other amplifiers is that it can provide amplification over a wide bandwidth.
Disadvantage: Causes distortion due to the nonlinear transfer characteristics of the TWTA
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
At low-input powers: output-input relationship is linear. At higher power input: the output power saturates Saturation point the maximum power output
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Intermodulation distortion: A serious effect of the nonlinear transfer characteristic of TWTA Non linear transfer characteristic is expressed as:
e0 ! aei bei cei ...
2 3
(7.1)
where, a,b,c e0 ei
= coefficients which depend on the transfer characteristics = output voltage = input voltage
The third order term, cei3, give rise to intermodulation products (most significant contributor)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Considering frequencies h1 and h2, these will give rise to 2h2-h1 and 2h1-h2 (As demonstrated in App.E of text book)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
and
2 f1 f 2 ! f1 (f
which fall on the neighboring carrier frequencies. To reduce the intermodulation distortion, the operating point of the TWT must be shifted closer to the linear portion of the curve. Reduction of input power input backoff
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Fig.7.21: Transfer curve for a single carrier and for one carrier of a multiple-carrier input. When multiple carriers are present, the power output around saturation, for any one carrier is less than that achieved with single-carrier operation.
Input backoff the difference in decibels between the carrier input at the operating point and the saturation input required for single-carrier operation. Output backoff corresponding drop in output power
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The flux density required at the receiving antenna to produce saturation of the TWTA saturation flux density.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Substituting in to Eq.(12.40),
P2 ?=M A! ?EIRPA ?FSLA 10 log 4T
(12.42)
Let,
P2 ?A0 A! 10 log 4T
(12.43)
(12.43)
(12.45)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Considering other propagation losses such as atmospheric absorption loss, polarization mismatch loss and antenna misalignment loss, (12.45) becomes
(12.46)
(12.47)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
(12.47) is for clear-sky conditions, with minimum value of [EIRP] which the earth station must provide to produce a given flux density at the satellite. We denote saturation values with subscript S, thus (12.47) becomes,
(12.48)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.7.2 Input backoff When a number of carriers are present simultaneously in a TWTA, the operating point must be backed off to a linear portion of the transfer characteristics to reduce intermodulation distortion. Suppose that the saturation flux density for a single-carrier operation is known. Input BO will be specified for multiplecarrier operation, referred to the single-carrier saturation level. The earth-station EIRP will have to be reduced by the specified BO, resulting in the uplink value of
(12.49)
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The total gives the carrier-to-noise density ratio at the satellite receiver as 74.5dBHz
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.7.3 The earth station HPA Earth station HPA has to supply radiated power plus transmit feeder losses, TFL (including waveguide, filter, coupler losses between HPA output and transmit antenna). From (12.3), power output of the HPA is given by
(12.51)
If the earth station transmit multiple carrier, it must be backed off, denoted by [BO]HPA. The earth station HPA must be rated for a saturation power output given by,
?P
HPA , sat
A! ?P A ?BOA
HPA
www.jntuworld.com
HPA
(12.52)
www.jntuworld.com
www.jwjobs.net
12.8 Downlink The downlink the satellite is transmitting the signal and the earth station is receiving it. Equation (12.38) can be applied to the downlink, but with subscript D to denote that the downlink is being considered.
C G ! ?EIRP AD ?LOSSES AD ?k A T D N0 D
(12.53)
Eq. (12.53) contains: the satellite EIRP, the earth station receiver feeder losses, and the earth station receiver G/T. The free-space and other losses are calculated for the downlink frequency.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The resulting carrier-to-noise density ratio given by Eq. (12.53) is that which appears at the detector of the earth station receiver. Where the carrier-to-noise ratio is the specified quantity rather than carrier-to-noise density ratio, Eq. (12.38) is used. On assuming that the signal bandwidth B is equal to the noise bandwidth BN, we obtain:
C G N ! ?EIRPAD T ?LOSSES AD ?k A ?B A D D
(12.54)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jwjobs.net
12.8.1 Output back-off Output back-off is 5dB less than input back-off
(12.55)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.8.2 Satellite TWTA output Satellite power amplifier, TWTA, has to supply the radiated power plus the transmit feeder losses. Losses include waveguide, filter and coupler losses between the TWTA output and satellites transmit antenna. From (12.3), power output of TWTA is
(12.56)
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
12.10 Combined Uplink and Downlink C/N Ratio The complete satellite circuit consists of an uplink and a downlink, as sketched in Fig. 12.9 a.
Figure 12.9 (a) Combined uplink and downlink (b) Power flow diagram for (a)
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Noise will be introduced on the uplink at the satellite receiver input. PNU = noise power per unit bandwidth PRU = average carrier at the same point The carrier-to-noise ratio on the uplink is (C/ No)U = (PRU/PNU). Note that power levels, and not decibels, are being used.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
PR
= carrier power at the end of the space link = the received carrier power for the downlink. = K x the carrier power input at the satellite
where K = the system power gain from satellite input to earth station input This includes the satellite transponder and transmit antenna gains, the downlink losses, and the earth station receive antenna gain and feeder losses.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
The noise at the satellite input also appears at the earth station input multiplied by K, and in addition, the earth station introduces its own noise, denoted by PND. Thus the end-of-link noise is KPNU + PND. The C/No ratio for the downlink alone, not counting the KPNU contribution, is PR/PND, and the combined C/No ratio at the ground receiver is PR/(KPNU + PND). The power flow diagram is shown in Fig. 12.9 b. The combined carrier-to-noise ratio can be determined in terms of the individual link values. To show this, it is more convenient to work with the noise-to-carrier ratios rather than the carrier-to-noise ratios, and these must be expressed as power ratios, not decibels.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Denoting the combined noise-to-carrier ratio value by No/C, the uplink value by (No/C)U, and the downlink value by (No/C)D then,
PR
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Equation (12.61) shows that to obtain the combined value of C/N0, the reciprocals of the individual values must be added to obtain the N0/C ratio and then the reciprocal of this taken to get C/N0. The reason for this reciprocal of the sum of the reciprocals method is that a single signal power is being transferred through the system, while the various noise powers which are present are additive. Similar reasoning applies to the carrier-to-noise ratio, C/ N.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com