Professional Documents
Culture Documents
Fuji Finepix-S5100 s5500
Fuji Finepix-S5100 s5500
+
FinePix S5100/S5500
USB cable
65
4. Adjustment FinePix S5100/S5500 Service Manual
Battery Voltage Adjustment
(1) Supply 4.34V (+0.02V/-0.00V).
When preparations are complete, press the [Enter] key.
<Fig. 4-13-2>
Battery Voltage Adjustment
<Preparations>
1. Check that the Power Cable Jig and the camera are connected.
*If not, return to the Jig Mode Setup screen,
and connect the Power Cable Jig and the camera.
2. Supply power (5.0V) to the camera from the
[Power Cable Jig].
When preparations are complete, press the [Enter] key on the PC.
---> Lens is extended when the [Enter] key is pressed.
<Fig. 4-13-1>
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
> The [4.34V Input] screen appears.
<Step 3>
> The [3.94V Input] screen appears.
66
4. Adjustment FinePix S5100/S5500 Service Manual
<Fig. 4-13-4>
Battery Voltage Adjustment
(1) Supply 4.34V (+0.02V/-0.00V).
When preparations are complete, press the [Enter] key.
Result= 6A
(2) Supply 3.94V (+0.02V/-0.00V).
When preparations are complete, press the [Enter] key.
Result= 63
(3) Supply 5.00V (+-0.05V).
When preparations are complete, press the [Enter] key.
<Fig. 4-13-3>
Battery Voltage Adjustment
(1) Supply 4.34V (+0.02V/-0.00V).
When preparations are complete, press the [Enter] key.
Result= 6A
(2) Supply 3.94V (+0.02V/-0.00V).
When preparations are complete, press the [Enter] key.
<Step 4>
> The [5.00V Input] screen appears.
<Step 5>
> Write the adjustment data to the Flash ROM when adjustment has been completed correctly.
> The [Battery Voltage Adjustment Complete] screen appears.
67
4. Adjustment FinePix S5100/S5500 Service Manual
<Fig. 4-13-5>
The BATTERY adjustment is completed.
Press the [Enter] key to return to the
Adjustment Item selection Screen.
<Step 6>
68
4. Adjustment FinePix S5100/S5500 Service Manual
Flash Adjustment
< Preparations >
(1) Prepare a gray chart (1000mm x 1000mm or more).
(2) Mount the camera on a tripod.
(3) Put the gray chart from the front side of the flash
on the place of 1000mm+/-10mm.
When preparations (1) - (3) are complete,
press the [Enter] key.
---> Lens is extended when the [Enter] key is pressed.
<Fig. 4-14-1>
4-14. [F7] : Flash Adjustment
<Setup for Flash Adjustment>
(1) As flash adjustment is readily affected by external light, ensure that the vicinity of the gray chart is very dark.
(2) Ensure that distance is measured from the front of the camera during flash adjustment.
(3) When adjusting the flash, always ensure that AF adjustment is complete before beginning flash adjustment.
Setup for Flash Adjustment
Gray chart
100010mm
Centerline
<Step 1>
Select [F7] Flash Adjustment on the [Adjustment Items Select] screen.
--> The [Flash Adjustment Preparation] screen appears.
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
--> The [Flash Adjustment Start] screen appears.
C
a
m
e
r
a
69
4. Adjustment FinePix S5100/S5500 Service Manual
<Step 3>
--> Write the adjustment data to the flash ROM when adjustment has been completed correctly.
--> The [Flash Adjustment Complete] screen appears.
<Step 4>
Flash Adjustment
(1) Adjust brightness so that the periphery of the gray chart
is as dark as possible.
(2) Adjust the camera so that the entire chart is
shown on the LCD monitor.
(3) Press the flash pop-up button.
When preparations (1) and (3) are complete,
press the [Enter] key.
|<-------------------------------------------------------->
| 1000 +-10mm
|
<---------------------Center--------------------->
CAMERA
< Setup for Flash Adjustment >
<Fig. 4-14-2>
Flash adjustment is completed.
Press the [Enter] key to return to the
Adjustment Item Selection Screen.
<Fig. 4-14-3>
70
4. Adjustment FinePix S5100/S5500 Service Manual
4-15. [F11] : Video Adjustment
<Setup for Video Adjustment>
(1) Set up the PCI-2746C board in the computer as explained in the instructions for the video adjustment jig.
(2) If the waveform of the brightness signal (Y) or color signal (C) does not appear in the WAVE No. 0 window during
adjustments, check the connections of the video adjustment jig.
<Step 1>
Select [F11] Video Adjustment on the [Adjustment Items Select] screen.
> The [Video Adjustment Preparation] screen appears.
FinePix S5100/S5500
PCI-2746C
Board
AC
100 ~ 240V
71
4. Adjustment FinePix S5100/S5500 Service Manual
Video adjustment was completed.
1. Disconnect Video cable from camera.
2. Close the [WaAVE No.0] window by close button.
Press the [Enter] key to return to the
Adjustment Item selection Screen.
<Fig. 4-15-2>
VIDEO Adjustment
< VIDEO Adjustment Preparations >
(1) Connect the camera and video adj. jig with the video cable.
(2) Confirm Video jig is connected with the video cable.
When preparations are complete,
press the [Enter] key.
<Fig. 4-15-1>
<Fig. 4-15-3>
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
> Write the adjustment data to the Flash ROM when adjustment has been completed correctly.
> The [VIDEO Adjustment Complete] screen appears.
<Step 3>
72
4. Adjustment FinePix S5100/S5500 Service Manual
4-16. [F8] : Firmware Download
Attention : When the download of the firmware is needed, FUJI SERVICE BULLETIN is contacted from
FTYO/QA. Till then, disregard this item.
<Setup for Firmware Download>
<Step 1>
Select [F8] Firmware Download on the [Adjustment Items Select] screen.
> The [Firmware Download Start] screen appears.
to USB Connector
to DC JACK
FinePix S5100/S5500
73
4. Adjustment FinePix S5100/S5500 Service Manual
Firmware download is completed
(1) Remove the Power Cable Jig from the camera.
(2) Turn off power switch.
(3) Reconnect Power Cable Jig.
(4) Turn on the power switch while pressing the shutter button.
(5) Press the [Enter] key after green LED lights on.
The system returns to the Jig Mode Setup screen
when press the [Enter] key.
<Fig. 4-16-2>
Firmware Download
LED lights to orange while downloading the firmware.
Do not turn off the power while downloading the firmware.
c:\FinePixS5100_5500_W\Firm_1_28\SU580RSC1_28.bin
Press the ENTER Key to start download.
<Fig. 4-16-1>
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
> The [Download Complete] screen appears if download is successful.
<Step 3>
74
4. Adjustment FinePix S5100/S5500 Service Manual
4-17. [F12] : End Setting
(Destination setting, USB ID write, Product mode setting)
1. The End setting consist of the following settings.
* Destination setting
* USB ID write
* Product mode setting (mass storage identification)
2. The setting must always be run when the adjustment software is terminated. Failure to run Terminal Setting will prevent
identification as Mass Storage when the camera is connected to the PC.
3. USB ID write details
1) USB ID write requires that the USB device (in this case FinePix S5100/S5500) be unique throughout the world. For this
reason, each device has a unique ID as determined by the USB standard. If multiple devices with the same USB ID are
connected to a single PC, the PC will be unable to identify each USB device, thus preventing operation.
Item Details
Repair Date Date information is acquired from the PC and written.
Administrator ID C(43)
Repair Station U.S. 61(a) SAPPORO 30(0)
Canada 62(b) SENDAI 31(1)
Hawaii 63(c) TOKYO 33(3)
Taiwan 64(d) NAGOYA 34(4)
England 66(f) OSAKA 35(5)
Germany 67(g) HIROSHIMA 37(7)
France 68(h) FUKUOKA 38(8)
Spain 69(i)
Italy 6A(j)
Netherlands 6B(k)
Belgium 6C(l)
Sweden 6D(m)
Switzerland 6E(n)
Norway 6F(o)
Finland 70(p)
Singapore 71(q)
China 74(t)
Ohter 7A(z)
Repair Serial No. A serial No. is assigned automatically and written
75
4. Adjustment FinePix S5100/S5500 Service Manual
Destination setting
The destination is selected from an undermentioned list,
according to third character from left side of the serial number.
The third character
<B> FinePix S5100 US/CA-model A to H,J,K
<C> FinePix S5500 EU/EG/GE/AS-model L to N,P to V
<Fig. 4-17-2>
End Setting
The End settings consist of the destination setting,
the USB_ID write, and product mode settings
(= Mass Storage recognition).
Press the [Enter] key.
<Fig. 4-17-1>
<Step 1>
Select [F12] End Setting on the [Adjustment Items Select] screen.
> The [End Setting Description] screen appears.
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
> The [Destination Setting] screen appears.
<Step 3>
<Note>
This example assumes that <B>US-Model has been selected. The following screen therefore appears.
> The [US-Model selected] screen appears.
76
4. Adjustment FinePix S5100/S5500 Service Manual
Destination setting
The destination is selected from an undermentioned list,
according to third character from left side of the serial number.
The third character
<B> FinePix S5100 US/CA-model A to H,J,K
<C> FinePix S5500 EU/EG/GE/AS-model L to N,P to V
Selected FinePix S5100 US/CA-model.
Press the [Enter] key!
<Fig. 4-17-3>
Repair site ID input menu
The repair site is selected from an undermentioned list.
<A> SAPPORO SS <M> BRITAIN
<B> SENDAI SS <N> GERMANY
<C> TOKYO SS <O> FRANCE
<D> NAGOYA SS <P> SPAIN
<E> OSAKA SS <Q> ITALY
<F> HIROSHIMA SS <R> NETHERLANDS
<G> FUKUOKA SS <S> BELGIUM
<H> USA <T> SWEDEN
<I> CANADA <U> SWITZERLAND
<J> HAWAII <V> NORWAY
<K> TAIWAN <W> FINLAND
<X> SINGAPORE
<L> CHINA <Z> OTHERS
<Fig. 4-17-4>
<Step 4>
> The [USB ID Writing] screen appears.
<Step 5>
<Note>
This example assumes that <H>USA has been selected. The following screen therefore appears.
> The [USA_ID USA] screen appears.
77
4. Adjustment FinePix S5100/S5500 Service Manual
<Step 6>
> The [FinePix S5100/S5500 Adjustment End] screen appears.
<Step 7>
USB ID
Selected USA.
Press the [Enter] key!
<Fig. 4-17-5>
<Fig. 4-17-6>
FinePix S5100/5500 Adjustment completed.
1) Remove USB cable from the camera.
2) Press the [Enter] key.
--> The adjustment software returns to the Jig mode setup screen
after press the [Enter] key.
78
5. Inspection FinePix S5100/S5500 Service Manual
5. Inspection
5-1. Required Measuring Equipment
Measuring equipment Remarks
Power supply AC adapter (AC-5V), Regurated power supply
Digital voltmeter For general use
Ammeter For general use (able to measure 1mA or less)
Power Cable Jig Common with adjustment JIG (ZJ00840-100)
xD-Picture card For general use
Macro Chart Resolution confirmation (ZJ00525-100)
TV Monitor NTSC, TV monitor, minimum resolution 600 lines
5-2. Connection of Measuring Equipment
Power Cable Jig.
The output current of the Regurated power supply must not become 2.5A or more.
FinePix S5100/S5500
79
5. Inspection FinePix S5100/S5500 Service Manual
5-3. Inspection and Factory Settings
Sequemnce Item Mode Preparations for adjustment
(measurement points, subject, other)
Method of adjustment
(VRs, waveforms, required values)
Measuring
equipment and jigs
Measurement points
(VRs, positions)
1
2
3
4
5
6
7
8
9
10
Check appearance
Power supply
switch
Check LCD
Check Movie
mode shock noise
Check macro
photography
Check focus
Movie recording
check
Movie play back
check
Resolution
confirmation
BATT cover detect
check
Delete mode
check
Auto
photography
LCD_ON
Auto
photography
Auto
photography
LCD_ON
Auto
photography
LCD_ON
Movie
photography
LCD_ON
Playback
Playback
Playback
LCD_ON
Delete
Visual check of camera
(1) Place BATTERY in camera
(2) Insert xD-Picture card and
close cover
(3) Turn on the power SW
(4) If the date set message
appears, press Back
(1) Press DISP/BACK button
(2) Press DISP/BACK button
(3) Press DISP/BACK button
(4) Press DISP/BACK button
(1) Apply an appropriate
shock to the camera.
* Do not apply shock directly
to the lens or card cover.
(1) Press Macro button
(2) Match the Black-Edged of
MACRO CHART to a full
angle of view of LCD
(3) Press shutter button to
take photographs
(1) Select Movie mode
(2) Half-press shutter button
-> full-press -> full-press
-> half-press -> release
(3) Half-press five seconds
later -> release
(1) Select Playback mode
(2) Press Down key to
playback movie
(1) Confirm the resolution of
the image recorded by 5
(2) Connect the TV monitoring
(1) Open card cover to check
recording
(1) Select <Delete all frames>
from the menu, and press
the <OK> button
(2) Press the <OK> button
again
No dents exterior of camera.
No problem with click action
of switches.
No dust or fogging of LCD
window.
(1) Applied 4AA batteries or
equivalent jig may be
used.
(2) Recording check card
(3) Power supply LED is green
and beeps
(4) Through screen and text
display in LCD.
(1) Framing guide is displayed
(2) Framing guide disappears
(3) The LCD display
disappears
(4) LCD is displayed
(1) No problem with display on
LCD monitor.
Restoration possible
despite disruption of sync.
(1) Macro icon appears in
LCD monitor
(3) LED beside viewfinder
changes from green to
orange (recording) to
green
(1) Standby display on LCD
(2) Movie recording begins.
Recording displayed on
LCD.
(3) Movie recording
completed. Recording on
xD-Picture card
(2) Movie played back on LCD
monitor
(1) Played back on LCD
monitor.
(2) Standard (Horizontal
resolution)
NTSC Center area : 350
Circumferential area : 300
PAL Center area : 300
Circumferential area : 250
(3) Thing of four even points
(1) Switch power OFF
(1) [OK to delete all frames?]
displayed
(2) Movie/photography screen
extinguished
MACRO
CHART
LCD monitor
LCD monitor
TV monitor
LCD monitor
LCD monitor
80
5. Inspection FinePix S5100/S5500 Service Manual
Sequemnce Item Mode Preparations for adjustment
(measurement points, subject, other)
Method of adjustment
(VRs, waveforms, required values)
Measuring
equipment and jigs
Measurement points
(VRs, positions)
11
12
13
Battery low check
Current
consumption
check
Factory setting
Factory setting
when updating
packaging
Movie
LCD_ON
Movie
photography
LCD_ON
Playback
(1) Connect Power Cable Jig
(2) Set voltage
(3) Turn on the Power SW
(4) Set to pre-end voltage
(5) Set to end voltage
(1) Connect Power Cable Jig
(2) Set voltage
(3) Turn on the Power SW
(4) Press the <LCD> button to
switch the LCD monitor
ON
(5) After the through screen is
displayed, check current
consumption
(1) Return all settings to initial
values
IMAGE DISP: ON
Power saving: 2 MIN
FORMAT: OK
FRAME NO.: CONT.
Beep: CENTER
SHUTTER: CENTER
Date/Time: Not set
Time DIFF.: Not set
LCD: ON
USB MODE: Card Reader
START-IMAGE OFF
LANG.: ENGLISH
VIDEO(US/CA): NTSC
(EU/EG/GE/AS):PAL
CCD-RAW: OFF
Self Timer: OFF
Mode Dial: AUTO
White Balance: AUTO
(2) Inspection battery/
inspection xD-Picture card
not inserted in camera
(3) Battery cover closed
(4) LCD surface free of
contamination
(5) Clean exterior of camera
(1) No damage to exterior
when checking (6) of 13
items
(2) Update packaging in
accordance with parts list
display
Refer to Battery Adjustment
for connection details
(2) Set voltage to 5.0 0.5V
(3) Starts normally
(4) Set voltage 4.34 0.2V
(5) Set voltage to 3.94 0.2V.
Lens retracts and main
power switched OFF
(2) Set voltage to 5.0 0.05V
(3) Starts normally
(5) Maximum current
consumption 450mA
* Setting and clearing date
(1) Connect the USB cable
from the PC to the camera
(ensure that the PC is
switched ON)
(2) Open the card cover and
switch power ON
(POWER_ON) while
pressing the shutter button
(3) Switch power OFF
(POWER_OFF)
(4) Check that the date has
been cleared
Power
Cable Jig
Regurated
power
supply
Power
Cable Jig
Ammeter
81
6. Parts List FinePix S5100/S5500 Service Manual
6. Parts List
6-1. Packing and Accessories
6-1-1. US-model (FinePix S5100)
Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL
A101
A102
A103
A104
A105
A106
A107
A108
A109
A110
A111
A112
A120
A116
A117/
A117B
A118
A119
A121
A122
A114 A115
A113
A101 FZ05983-200 UNITARY BOX WU S5100 N
A102 FZ05328-100 SHEET MOLD N
A103 BB13000-100 PARTITION PAD WU S5100 N
A104 BB12943-100 BAR CODE LABEL BLANK N
A105 AZF0000-311 HDPE BAG NO.11 N
A106 FZ04793-100 ALKALINE BATTERY =
A107 FZ04741-100 VIDEO CABLE N
A108 FZ05365-100 USB CABLE N
A109 BU02939-100 SHOULDER BELT ASSY N
A110 BU02876-100 LENS CAP ASSY N
A111 BU03097-100 LENS HOOD ASSY N
A112 AZF0000-101 LDPE BAG NO.10 N
A113 BB18002-100 CERTIFICATION SEAL N
A114 BF04146-100 XDCARD 16MB ASSY =
A115 BL00209-100 CASE_XD-CARD for XD CARD N
A116 FZ05352-500 CD-ROM SX4.2G N
A117 BB18294-100 DEST.LBL.5800US J FG N
A117B BB18294-A00 DEST.LBL.5800US C FG
A118 BL00372-100 IMPORTANT SAFETY N
A119 BL00373-100 US WARRANTY N
A120 BL00416-200 MANUAL (ENG) N
A121 BL00417-200 QUICK MANUAL (ENG) N
A122 BL00417-500 QUICK MANUAL (SPA) N