6SE483 9610 1996 DETROIT DIESEL CORPORATION From Bulletin 21-60-98 1-503 Exceptions to Standard Fastener Torque Specifications Listed in Table 1-41 are exceptions to standard fastener torque specifications supporting the Series 60 Engine. Section Fastener Size N m (lb ft) Refer to section 1.6.3.1 Breather Housing to Rocker Cover Cap - 2.5 1.833 Refer to section 1.2.5 Cylinder Head Bolt (torque twice) M16 X 2.0 250 - 285 (185 - 210) Refer to section 2.2.5 Bolt, Inj. Harness Mounting Flange M8 X 1.25 10-15 (7-11) Refer to section 1.6.8 and refer to section 1.6.9 Bolt, Rocker Cover-to Cylinder Head 3/8-16 20-25 (15-18) Refer to section 1.9.3 Bolt, Main Bearing Cap M20 X 2.5 470-530 (347-391) Refer to section 1.10.3 Plug, Gear Case Adj. Idler Oil Hole 5/16-24 15-20 (11-15) Refer to section 1.13.3 Bolt, Front Pulley 9/16-18 182-210 (134-155) Refer to section XXX Bolt, FlywheelHsg. Mounting M12 X 1.75 112-126 (83-93) Refer to section 1.14.3 Bolt, Flywheel 9/16-18 68(+120 ) (50)(+120 ) Refer to section 1.19.4 Nut, Connecting Rod M14 X 1.5 160-185 (118-137) Refer to section 1.22.6 Bolt, Camshaft Bearing Cap M12 X 1.75 126-146 (93-108) Refer to section 1.3.3 Bolt, Rocker Arm Shaft M12 X 1.75 126-146 (93-108) Refer to section 1.22.6 Nut, Nos. 1&7 Camshaft Cap M12 X 1.75 126-146 (93-108) Refer to section 1.22.6 Stud, Nos. 1&7 Camshaft Cap M12 X 1.75 126-146 (93-108) Refer to section 1.23.4 Bolt (Solid), Camshaft Drive Gear M18 X 1.5 243-278 (55)(+90 ) Refer to section 1.24.3 Nut, Adjustable Idler Assy. M12 X 1.75 57-67 (42-49) Refer to section 1.25.3 Bolt, Bull Gear Assy-to-Block M12 X 1.75 101-116 (75-86) Refer to section 1.25.3 Nut, Bull Gear Assy (LH thread) 2-1/2-18 940-1000 (693-738) Refer to section 1.27.4 Nut, Accessory Drive Pulley M24 X 1.0 220-250 (162-185) Table 1-41 Exceptions to Standard Fastener Torque Specifications All information subject to change without notice. 1-504 From Bulletin 21-60-98 6SE483 9610 1996 DETROIT DIESEL CORPORATION SERVICE TOOLS Listed in Table 1-42 , listed in Table 1-43 , listed in Table 1-44 , listed in Table 1-45 , listed in Table 1-46 , and listed in Table 1-47 are the service tools supporting the Series 60 engine. Tool Number Tool Name J 29109 Engine Stand J 36375 Flywheel Lock PT-7276 Gasket Eliminator (Loctite 51580) J 35951 Hydraulic Shop Press (17.5 ton) J 35951-175 Hydraulic Ram and Pump (included in J 35951 ) J 7079-2 Driver Handle J 38977 Water Pump Gear Lash Checker J 35635-A Engine Stand Adaptor Plate J 5347-B Dial Bore Gage J 26558-92 Loctite Pipe Plug Sealant J 35996-A Rocker Arm & Shaft Assembly Lifter J 4757 Micrometer Ball Table 1-42 General Shop Tools
Gas-Engines and Producer-Gas Plants
A Practice Treatise Setting Forth the Principles of Gas-Engines and Producer Design, the Selection and Installation of an Engine, Conditions of Perfect Operation, Producer-Gas Engines and Their Possibilities, the Care of Gas-Engines and Producer-Gas Plants, with a Chapter on Volatile Hydrocarbon and Oil Engines