ANTICORIT DFW is a corrosion preventive and dewatering fluid that forms a waxy-oily film when the solvent evaporates, offering excellent corrosion protection and dewatering properties. It is recommended for drying and protecting metal components after galvanizing or washing, and provides consistent friction for galvanized screws. ANTICORIT DFW complies with VW TL 52 111 and FORD SZ 600 A specifications for friction coefficients and corrosion protection. It can be applied by dipping or spraying and offers corrosion protection for up to 300 hours in humidity cabinets, 24 hours in salt spray tests, and 30 cycles in condensation climate tests when stored sealed for 5 years at 5-40°C.
ANTICORIT DFW is a corrosion preventive and dewatering fluid that forms a waxy-oily film when the solvent evaporates, offering excellent corrosion protection and dewatering properties. It is recommended for drying and protecting metal components after galvanizing or washing, and provides consistent friction for galvanized screws. ANTICORIT DFW complies with VW TL 52 111 and FORD SZ 600 A specifications for friction coefficients and corrosion protection. It can be applied by dipping or spraying and offers corrosion protection for up to 300 hours in humidity cabinets, 24 hours in salt spray tests, and 30 cycles in condensation climate tests when stored sealed for 5 years at 5-40°C.
ANTICORIT DFW is a corrosion preventive and dewatering fluid that forms a waxy-oily film when the solvent evaporates, offering excellent corrosion protection and dewatering properties. It is recommended for drying and protecting metal components after galvanizing or washing, and provides consistent friction for galvanized screws. ANTICORIT DFW complies with VW TL 52 111 and FORD SZ 600 A specifications for friction coefficients and corrosion protection. It can be applied by dipping or spraying and offers corrosion protection for up to 300 hours in humidity cabinets, 24 hours in salt spray tests, and 30 cycles in condensation climate tests when stored sealed for 5 years at 5-40°C.
ANTICORIT DFW is a corrosion preventive and dewatering fluid which, when the solvent evaporates, forms a soft, waxy-oily film. This offers excellent corrosion protection, intensive dewatering properties, stability against dragged-in acids and alkalines along with being extremely economical. ANTICORIT DFW is recommended for the rapid drying and simultaneous protection of metal components and tools; after galvanizing and washing processes for the interim and long-term protection of bare metal surfaces. ANTICORIT DFW gives galvanized screws a consistent coefficient of friction. Even if the fastener is repeatedly retightened the torque variation remains minimal. The product allows automatic screw and nut drivers with preset torques to work with the utmost of accuracy and reliability. ANTICORIT DFW complies with the VW TL 52 111 and FORD SZ 600 A specifications concerning friction coefficients and additionally offers good corrosion protection. Application: Normally by dipping but if such facilities are not available ANTICORIT DFW can be sprayed. However, all precautions applicable to solvent-based products should be observed. If necessary, please consult the corresponding Material Safety Data Sheet. If sealed in the original container, ANTICORIT DFW can be stored for min. 5 years at 5 - 40 C. Characteristics: Properties Unit Value Test method Colour 5.0 ASTM D 1500 Flashpoint C 40 ASTM D 56 Density at 15 C kg/l 0.820 ASTM D 1258 Viscosity at 20 C mm/s 2.2 ASTM D 445 Film weight g/m 0.9 FLP-F 3 *) Evaporation residue % 22 FLP-V 1 *) Corrosion Protection Data (on RRSt. 1405 m test panels)
Humidity cabinet hours 300 ASTM D 1748 Salt spray test hours 24 ASTM B 117 Condensation climate cycles 30 DIN 50 017 KFW *) = FUCHS Laboratory procedure Disclaimer of Liability FUCHS PETROLUBE (M) SDN BHD http://www.fuchs.com.my/en/products/print.php?id=812 1 of 1 26.06.2014 10:54