1. The document provides work instructions for removing and inserting valves from cylinders using a Fredlov Valving Machine. It describes setting pressures, positioning the cylinder and valve jaw, and using lever controls to carefully remove and insert valves.
2. It also includes a table with torque pressures and values for inserting valves into cylinders of different sizes.
3. The final section provides maintenance points for the machine, such as cleaning the motor drive box weekly, checking and adding lubricant oil, and greasing poles and checking gears.
1. The document provides work instructions for removing and inserting valves from cylinders using a Fredlov Valving Machine. It describes setting pressures, positioning the cylinder and valve jaw, and using lever controls to carefully remove and insert valves.
2. It also includes a table with torque pressures and values for inserting valves into cylinders of different sizes.
3. The final section provides maintenance points for the machine, such as cleaning the motor drive box weekly, checking and adding lubricant oil, and greasing poles and checking gears.
1. The document provides work instructions for removing and inserting valves from cylinders using a Fredlov Valving Machine. It describes setting pressures, positioning the cylinder and valve jaw, and using lever controls to carefully remove and insert valves.
2. It also includes a table with torque pressures and values for inserting valves into cylinders of different sizes.
3. The final section provides maintenance points for the machine, such as cleaning the motor drive box weekly, checking and adding lubricant oil, and greasing poles and checking gears.
1. The document provides work instructions for removing and inserting valves from cylinders using a Fredlov Valving Machine. It describes setting pressures, positioning the cylinder and valve jaw, and using lever controls to carefully remove and insert valves.
2. It also includes a table with torque pressures and values for inserting valves into cylinders of different sizes.
3. The final section provides maintenance points for the machine, such as cleaning the motor drive box weekly, checking and adding lubricant oil, and greasing poles and checking gears.
CHECK THE CYLLINDER ARE EMPTY BY BLOWING N2 TO THE CYLLINDER AND MAKESURE THERE ARE NO PRESSURE LEFT 1. Removing Valve a. Check the clamp control pressure are set at 90 Psig b. Set the angle and high of the Valve Jaw c. Pull the Clamp control d. Mark the cylinder with related valve e. Place the cylinder in f. Set the cylinder to be centralize with the Valve Jaw by turning the Manual Clamp g. Push the clamp control to seal the cylinder h. Fit The Valve Jaw to the cylinder valve, by holding the Valve Jaw and set the lever to Remove Carefully i. Fully set the lever to Remove until the valve is remove from the cylinder j. Pull the clamp control to release the cylinder k. Take the cylinder out and check for internal cleaning 2. Inserting Valve l. Confirm the Torque of the cylinder and valve (choose the smaller) m. Set the angle and high of the Valve Jaw n. Pull the Clamp control o. Place the cylinder in p. Set the cylinder to be centralize with the Valve Jaw by turning the Manual Clamp q. Push the clamp control to seal the cylinder r. Put the valve, insert it by hand s. Fit The Valve Jaw to the cylinder valve, by holding the Valve Jaw and set the lever to Remove Carefully t. Set the pressure of the torque according the cylinder / valve information Pressure (Psig) 10 20 30 40 50 60 70 80 90 Insertion (Torque) in lb 100 210 340 425 500 580 700 760 860 Insertion (Torque) N m 11.3 23.7 38.4 48 56.5 65.5 79.1 85.9 97.2
u. Fully set the lever to Insert until the valve is inserted to the cylinder until 2 3 thread are left v. Pull the clamp control to release the cylinder
Manual Clamp Maintenance Of Fredlov Valving Machine
Please Observe this point : 1. Clean the compartment motor drive box every Monday morning 2. Check the level of Lubricant Oil, Add if necessary with Air Tools Oil 3. Make sure that the Lubricant Oil drip each of 10 motor cycle 4. Make sure there are no particle inside of cylinder 5. Grease the Pole thin 6. Make sure not too stress that the gear chain