This document is a schematic for a pulsed half power resonant ballast intended for plasma displays and hydrogen production. It shows the circuit design including transformers, transistors, capacitors, and other components. Proprietary information is included regarding transformer specifications, operating frequencies, and component values for powering different types of plasma tubes at various voltages and currents.
This document is a schematic for a pulsed half power resonant ballast intended for plasma displays and hydrogen production. It shows the circuit design including transformers, transistors, capacitors, and other components. Proprietary information is included regarding transformer specifications, operating frequencies, and component values for powering different types of plasma tubes at various voltages and currents.
This document is a schematic for a pulsed half power resonant ballast intended for plasma displays and hydrogen production. It shows the circuit design including transformers, transistors, capacitors, and other components. Proprietary information is included regarding transformer specifications, operating frequencies, and component values for powering different types of plasma tubes at various voltages and currents.
DIDRIV10/PVM500DC SCHEMATIC for PULSED HALF POWER RESONANT OPERATION REV2110-11
Intended for dielectric barrier discharge systems/plasma displays/hydrogen production
PVM400DC/DIDRIV10 C12 .01/2K CO1 CORD 2A F1 S1 Rth Proprietary and intellectual property of INFORMATION UNLIMITED PO Box 716 Amherst N.H. 03057 Tel# 1 603 673 6493/4730 Fax# 1 603 672 5406 EMAIL to <BOB@AMAZING1.COM> Web site at <http:// www.amazing1.com> SHORT FOR FULL POWER P1 AC IN BLK GRN WH TRANSFORMER BASIC/OZONE RESONANT NON RESONANT PRIMARY..65 turns of #20 LITZ 80 50 Lp sc . .82 mh Lp oc ... 4.75 mh SECONDARY..1000 turns of #26 MAG 2500 4000 Ls sc..1.26 h Lp oc..... 7.23 h AIR GAP2 MILS/SIDE CORE CURRENT ....40658...2.72 x 1.325 x .675 CORE reclaim ....40787...2.72 x 1.53 x .675 CORE intl ferrite...3.2 x 1.756 x .625 CORE intl ferrite...3.2 x 1.285 x .625 SET...............................35 us on 48 x 4 column foe .8 amps cold 1 2 3 4 5 6 7 8 R12 510K 1W R1 220 1W P3 10KP R10 5KT R11 1K R4 2KT F=16-66KHZ with R10 max R6 15 R7 15 R8 10/3 C10 220 C20 220 **CX .1 C2 10 C8 .47 C3 .01 C4 .1 C5 1.5 C6 1.5 C7 .0015 T1 PRI 65T #20 SEC XXXX IR2153 D5 IN4937 NEON Q1 1R450 Q2 IR450 TP3 P10.1 TP1 .4V 1N5408 D1 D3 D2 D4 3A 1N4001 12/.1 1 12 1000/25 555 .01 1K 1K 1K 10K S3 4 8 7 6/2 1 5 3 914 1 .1 2222 .01 pulse rep rate 250 hz on time 3.5-.5 USE 220 VOLT 12 VOLT TRANSFORMER FOR 220 UNITS AND REMOVE SHORT 10 K POT SHOULD BE ON FRONT PANEL Resonant frequency of 4" plasma tube is 55 khz current draw is .1 to .6 amps in ballast mode with dc adjust at max 150 volts S2 down 300 volts S2 up 12 VOLTS EC103D1 A K G S2 L/H R12 27 1N5245 100K 10K R3000 T1 F194..2500T FOR 0-25 PFD F196..1000T FOR 25-200PFD VA1 S3/10K 10K ???? Output can be controlled by turning the 2222 transistor off and on. The 555 is easily removed from its socket allowing signal insertion via the 1 k resistor going to pin 3 NOTES: 2500 TURNS SELF RESONANT TO 25 PFD EXTERNAL CAPACITANCE 1000 TURNS RESONANT WITH 40-200 PFD EXTERNAL CAPACITANCE