Professional Documents
Culture Documents
27 OMC-Radio-Parameters-104-ok
27 OMC-Radio-Parameters-104-ok
ZTE University
CDMA-BSS Course Team
Main Content
BSS Parameters
BTS Parameters
Cell Parameters
Carrier Parameters
Channel Parameters
BSS Parameter
BSS Parameters
Gain Parameters
RLP Parameters
Switch Parameters
BSS Parameters
BSS Parameters
MSC ID
Description :Switch ID.
Service provider specifies this parameter. The first 16 digits represent Market
background.
(IMSI).
China = 460, USA = 310, Canada =302a, Singapore = 525.
BSS Parameters
MS IMSI_11_12
Value Range: 00~99
IMSI Structure
Default: 03
Description: the eleventh and twelfth digits of the IIMSI, when IMSI is 15 digitals
BSS Parameters
BSS Parameters
supported.
service zone, the base station shall set this field to its
non-zero packet data services zone identifier. If the
base station does not support a packet data service
zone, the base station shall set this field to 0.
BSS Parameters
BSS Parameter
BSS Parameters
Gain Parameters
RLP Parameters
Switch Parameters
BSS Parameter
BSS Parameters
Gain Parameters
RLP Parameters
Switch Parameters
BSS Parameter
BSS Parameters
Gain Parameters
RLP Parameters
Switch Parameters
BSS Parameter
BSS Parameters
Gain Parameters
RLP Parameters
Switch Parameters
Default: 2
Description: Not Protocol Filed.
SwitchNumber
Value Range: 0~255
Default: Description: used to uniquely identify a special
BSS Parameter
BSS Parameters
Gain Parameters
RLP Parameters
Switch Parameters
BSS Parameter
BSS Parameters
Gain Parameters
RLP Parameters
Switch Parameters
BSS Parameter
Gain Parameters
RLP Parameters
PTT SCH Parameters
Pay Phone Parameters
Special Number Parameters
Switch Parameters
Main Content
BSS Parameters
BTS Parameters
Cell Parameters
Carrier Parameters
Channel Parameters
BTS Parameters
The parameters
of this table are
used for EV-DO
service!
BTS Parameters
control step length is set too high, the forward quick power control
response time is short, but the stable state power deviation is high. If
the power control step length is set too low, the stable state power
deviation is low, but the forward quick power control response time is
long.
power control step length is set too high, the forward quick power
control response time is short, but the stable state power deviation is
high. If the power control step length is set too low, the stable state
power deviation is low, but the forward quick power control response
time is long.
BTS Parameters
The power
assigned by BTS
to a subscriber.
Maximum
Initial
Power
Minimum
These two parameters
decide Maximum
threshold and
Minimum threshold
179
the initial transmitting power is set too high, F-FCH initial transmitting
power is high, and the MS is easier to receive information correctly
(Frame Error Rate is low), but the forward capacity is lowered when
the channel is established. If the initial transmitting power is set too
low, F-FCH initial transmitting power is low, and the MS may receive
wrong information (Frame Error Rate is high), but the forward power
resource is saved.
Main Content
BSS Parameters
BTS Parameters
Cell Parameters
Carrier Parameters
Channel Parameters
Cell Parameter
Cell Parameter
System Parameter
Handoff Parameter
Link Cell
Neighbor Frequency
Cell Parameter
Cell Parameter
Cell Parameter
a cellular system.
Cell Parameter
Cell Identity : CI
Default:-
Default: 4
Cell Parameter
Search window size for the Active Set and Candidate Set:
SRCH_WIN_A
Value Range: 0~15
Default:6
Default: 0
Cell Parameter
Cell Parameter
System Parameter
Handoff Parameter
Link Cell
Neighbor Frequency
System Parameter
System Parameter
Cell Parameter
Cell Parameter
System Parameter
Handoff Parameter
Link Cell
Neighbor Frequency
Cell Parameter
Cell Parameter
System Parameter
Handoff Parameter
Link Cell
Neighbor Frequency
Handoff Parameter
Handoff Parameters
Handoff Parameters
Default: 3
Description: If the pilot signal is in the candidate pilot signal set and also if
the time when its strength is less than T_DROP continuously exceeds
T_TDROP, the pilot signal will be transferred to the neighbor pilot signal set.
Time (seconds)
T_Tdrop
Time (seconds)
0.1
27
39
10
55
11
79
12
112
13
159
13
14
225
19
15
319
Unit: -
Cell Parameter
Cell Parameter
System Parameter
Handoff Parameter
Link Cell
Neighbor Frequency
Default: 3
Cell Parameter
Cell Parameter
System Parameter
Handoff Parameter
Link Cell
Neighbor Frequency
Cell Parameter
Cell Parameter
System Parameter
Handoff Parameter
Link Cell
Neighbor Frequency
Cell Parameter
Cell Parameter
System Parameter
Handoff Parameter
Link Cell
Neighbor Frequency
Link Cell
Add neighbor PN
According to designing.
Cell Parameter
Cell Parameter
System Parameter
Handoff Parameter
Link Cell
Neighbor frequency
Neighbor frequency
Cell Parameter
Cell Parameter
System Parameter
Handoff Parameter
Link Cell
Neighbor frequency
We can adjust
how to repeat
ECAM here.
Main Content
BSS Parameters
BTS Parameters
Cell Parameters
Carrier Parameters
Channel Parameters
Carrier Parameter
Carrier Parameter
Access Parameter
Traffic Parameter
Carrier Parameter
Carrier Parameter
Carrier Parameter
respectively
Default: 0
Description: Nominal transmit power offset, expressed
in binary supplemental code. This parameter and the
parameter Extended nominal transmit power are used
in the open loop power control of reverse links.
Carrier Parameter
Carrier Parameter
Carrier Parameter
Access Parameter
Traffic Parameter
Carrier Parameter
Just default!
Carrier Parameter
Carrier Parameter
Access Parameter
Traffic Parameter
Carrier Parameter
Carrier Parameter
Access Parameter
Traffic Parameter
Access Parameter
Access Parameter
Access Probing
Access Channel
Request Attempt
Sequence MAX_RSP_SEQ
Access Probe
Sequence 1
Sequence 2
Sequence 3
(15max)
System Time
PD
RS
PD =0 for
Response
Message
PD
RS
PD
Access Procedure
is depending on the
Access parameter .
Access Probe 3
PI
Access Probe
PI
Access Probe
IP
System Time
TA
RT
TA
RT
TA
Access Parameter
Default: 3
Default: 6
Access Parameter
MAX_CAP_SZ
Unit: Frame
Value range: 0 ~ 7
Default: 3
Description: Maximum Access Channel message capsule size. 3 less than
PAM_SZ
Unit: Frame
Value range: 0 ~ 15 Default: 3
Description:Access Channel preamble length. 1 less than the number of
Access Channel frames that mobile stations are to transmit in each Access
Channel preamble.
Access Parameter
PROBE_BKOFF
Value Range: 0~15
Default:0
BKOFF
Value Range: 0~15 Default:0
Description: For every access probe sequence, a backoff delay, RS,
Access Parameter
ACC_TMO
Unit: 80ms
Value Range: 0~15 Default:3
Description:After sending the access probe, The MS shall wait ACK
PROBE_PN_RAN:
Value Range: 0~9 Default:0
Description: Time randomization for access channel probes.To avoid
0 ~ 2PROBE_PN_RAN-1
Carrier Parameter
Carrier Parameter
Access Parameter
Traffic Parameter
Carrier Parameter
Carrier Parameter
Access Parameter
Traffic Parameter
Value: 0~30000
Description: Designed power of the cell.
Carrier Parameter
Carrier Parameter
Access Parameter
Traffic Parameter
Carrier Parameter
Carrier Parameter
Access Parameter
Traffic Parameter
Traffic Parameter
CE search window
Main Content
BSS Parameters
BTS Parameters
Cell Parameters
Carrier Parameters
Channel Parameters
Channel Parameters
Pilot Channel
Synchronous Channel
Paging Channel
Access Channel
ModuleId
Value range:
Default: 1
Description: Module where the Pliot channel is located,The
ElementId
Value range: 0 ~ 35
Default: 0
Description: Element where the pilot channel is located. The
Unit: (X-255)/4
Value range: 0 ~ 255
Default: 225
Description : Provided by network planning, generally