Professional Documents
Culture Documents
Psi Chart As Per Pipe WT
Psi Chart As Per Pipe WT
Psi Chart As Per Pipe WT
WORKING
FACTOR
FACTOR
PIPE
WORKING
7900
3500
BURST
NO.
BURST
1870
810
8463~
3000
1800
XXS
7200
9500
2070
XXS
XXS
6900
4780
6100
5300
4660
3560
2700
2100
2800
2000
1900
2090
2600
1600
160
80
40
1SCH.
20865PRESSURE-PSI
2500
1500
40
169
NO.
80
26.8
40
3850
22.3
4400
1100
160
3760
6A.3
*80
18.2
12.9
15.0
1.02
.738
.519
3800
4350
12300
10000
2300
4100
4800
1700
4500
6300
1500
2400
1030
2300
4200
3700
4100
3300
1800
4.0212
H80
XXS
36.1
160
2.60
10.9
80
1.67
40
2.08
2.92
12
1400
9.46
30.5
1.51
.422
160
8500
5700
1210
1300
3740
5.7410
36.9
.960
.666
.340
4600
160
8.60
SCH.
1.32
PRESSURE-PSI
4000
44.5
63.4
40
80
2.17
13.7
1.94
4.54
3.56
5.43
.244
.239
33~
2~
7300
.529
20.3
2.47
7.82
4.64
.385
1.49
.912
6.52
15,900
13,500
27,700
12,600
9,100
6,900
XXS
25,300
13,900
18,100
18,000
12,200
13,000
9,400
22,1
12,600
17,700
11,200
15,700
14,200
8,100
9,000
00
3452~
25,000
22,300'
11,000
12,500
7,800
17,500
12,100
32,700
10,100
23,000
20,500
16,200
6,600
4,500
7,800
J40
.06
22,500
16,200
20,200
21,000
26,400
11,500
17,600
28,000
12,900
19,500
15,600
15,000
12,300
10,300
8,500
35,000
42,100
6,500
6,800
7,400
9,500
26,700
6,300
5,500
5,100
@40
1000
3,800
4,\00
PIPE
INCHES
NOM.
SIZE WATER
P=
D-2y(t-C)
where P = allowable.pressure in lb per sq in. (gauge)
S = allowable working stress in lb per sq ip..
D = outside diameter in inches
t= design thickness in inches, or 121/2% less than
the nominal thickness shown in the table
C = allowance in inches for corrosion ~d/ or
mechanical strength (C==O.05"hasbeen used above
for all pipe sizes)
y = a coefficient having values for feirriticsteels, as
follows:
0.4 up to and including 9000P
0.5 for 9500P
0.7 for 10000P and above
The allowable working stresses were obtained
from the Code for Pressure Piping, ASA B31.1.1-1955,
Table 12.
Hydraulic machinery piping is not covered by the
Code for Pressure Piping, but it is current practice to use
stresses comparable with those given for Refinery and
Oil TransportationPiping, Div. A. Theallowableworking
OD
t
25t
OD
=
=
=
=
PE
INT
WALL
.095
.432
.355
.318
.21B
.337
.147
.594
.500
.688
.191
.276
.200
.375
.300
.154
.179
.119
.126
INT
INT
.552
.436
.864
.382
.308
.358
,600
.674
.750
1.000
.875
1.000
..400
294
WALL
2FPS
638.6
SIZE
GPM@
PIPE
1.714
55.6
14.9
9.029
6.9
83.4
9.2
2.3
116
2.300
195
260
4.897
4.063
581
942
'22.1
203
81.2
295
233
377
118
568..
10.75
569
AREA
10
15
20
26
10
FT
FPS
FPS
FPS
GPM@
GPM@
GPM@
19.8
3.659
6.408
13.3
2.440
4.6
1.100
29.8
1.6
1.503
21/2
1.771
8.8
77.1
.282
29.6
2.4
.148
11/4
.599
4.4
.896
3.1
.434
17.7
9.9
39.5
.79
1/2
27.9
154
49.4
74.4
139
193
3.9
111
3/4
15.4
11.1
1.8
1"
4.0
.93
6.0
2.32
3.152
244
367
4.154
27.54
130
48B
122
26.0
3412
1883
6.875
5!lO
406
8.750
1180
38.55
609
53.16
72.42
104.1
60.13
2825
1015
18.83
37.12
2325
3767
1475
1421
90.76
4264
125.5
5686
7107
WTI
5.214
.630
44.6
.050
13.70
2.463
11.6
11/2
1.774
59.5
.950
.252
18.58
7.803
65.1
325
611
48.9
1163
885
1744
12.97
812
2907
4709
10
2843
INT