Professional Documents
Culture Documents
Exciter: S.No. Sub-Unit R & S Part No
Exciter: S.No. Sub-Unit R & S Part No
INTRODUCTION
Exciter type SU-115 generates FM signals in the frequency range 87.5 to 108 MHz in steps
of 10 kHz. Its normal RF output power is 10 Watt. However, output power of 30 MW or 1 W
can also be obtained with the help of internal links and switches.
A simplified Block Diagram of the Exciter is shown in given fig. 1. L and R audio signals are
fed to stereo coder card. These are pre-emphasised as per 50 u sec Pre-Emphasis curve.
The pre-Emphasis can be switched OFF if required with the help of a switch provided on the
front panel. These signals are then stereo encoded. Output of stereo coder cord is a
multiplexed (MPX) signal which modulates the RF signal generated in the VCO. The
modulated output is passed through a PIN diode regulator and then amplified in three stages
to get an output of 10 W. Harmonics are removed by 110 MHz Low Pass Filter. The
Directional coupler senses are forward and reflected voltages which are processed in
Comparison & Logic circuits. Automatic level control (ALC) circuit stabilizes the output
power of the Exciter under adverse operating conditions of mismatch (VSWR > 1.5),
temperature and power supply variations.
SUB-UNITS
The main sub-units of the Exciter are :S.No.
Sub-Unit
1.
674.0345
2.
Input Board
674.0316
3.
Stereo Coder
674.0216
4.
674.0574
5.
Synthesiser
594.2059
6.
Filter Board
674.0597
7.
674.0451
8.
28 V Regulator Board
674.0716
STI(T) Publication
35
007/2003
FM Transmitter
For stereo operation, the L and R signals available at the output of Input Board are fed to
two identical circuits in the stereo coder unit. Here Pre-emphasis is introduced which can be
switched ON or OFF from the front panel. There stereo or multiplexed (MPX) signal is fed to
a summing amplifier to which pilot tone (19 kHz) is added. SCA and traffic signals can also
be added here if desired. The summed output is fed to a MPX Low Pass Filter which
suppresses the harmonics of the 38 kHz sub-carrier.
The MPX signal is amplified to a level of +6 dBm. The audio level (mono or stereo) going
into the synthesizer is sampled and applied to a peak detector for metering of DEVIATION (
f) on the front panel. L and R audio levels and pilot level are also metered. Output of the
synthesizer is FM signal. The modulated signal is amplified to a level of about 2 V and fed to
the Filter Board which consist of
1 W RF Amplifier stage.
Switching Facilities for getting three output powers of 30 mW, 1 w and 10 W.
Output filter.
Directional coupler
The 10 watt amplifier is a separate stage mounted behind the front panel. Its heat sink is
visible on the front side and is convection cooled. The 10 watt output is taken out at the 50
ohms connector at the rear.
OPERATING INSTRUCTIONS
1.
2.
Functions of front-panel controls and displays are shown in fig. 4 (a) & (b) and pin
assignments of rear panel in fig. 5.
3.
The output power of the transmitter can be set with level adjuster (12) on the front
panel. If the set value exceeds the internally set threshold value, the RF
Present LED (13) lights.
4.
The output power, L & R audio levels, frequency deviation and pilot tone level
can be read on the meter with the help of selector switches (1) and (2).
5.
The audio level and hence frequency deviation of the transmitter can be adjusted
with input-signal BCD switches (4).
STI(T) Publication
36
007/2003
Exciter
STI(T) Publication
37
007/2003
FM Transmitter
1.
Power Supply
2.
3.
AF Section
4.
5.
6.
7.
Coder
8.
Input Board
9.
STI(T) Publication
38
007/2003
Exciter
STI(T) Publication
39
007/2003
FM Transmitter
STI(T) Publication
40
007/2003
Exciter
41
007/2003
FM Transmitter
42
007/2003