This document provides instructions for adjusting the factory mode settings on a service manual for the BML Myanmar.
1. The IF PLL adjustment involves injecting a test signal, accessing the factory mode settings, and adjusting the IF coarse and fine tuners to get the AFC into the correct low or high position.
2. The AGC adjustment involves injecting a normal channel signal at 60dB, monitoring the AGC voltage, and adjusting the AGC setting until the voltage reaches the specified level for the tuner model.
3. Pressing the MENU button saves the adjustment data.
This document provides instructions for adjusting the factory mode settings on a service manual for the BML Myanmar.
1. The IF PLL adjustment involves injecting a test signal, accessing the factory mode settings, and adjusting the IF coarse and fine tuners to get the AFC into the correct low or high position.
2. The AGC adjustment involves injecting a normal channel signal at 60dB, monitoring the AGC voltage, and adjusting the AGC setting until the voltage reaches the specified level for the tuner model.
3. Pressing the MENU button saves the adjustment data.
This document provides instructions for adjusting the factory mode settings on a service manual for the BML Myanmar.
1. The IF PLL adjustment involves injecting a test signal, accessing the factory mode settings, and adjusting the IF coarse and fine tuners to get the AFC into the correct low or high position.
2. The AGC adjustment involves injecting a normal channel signal at 60dB, monitoring the AGC voltage, and adjusting the AGC setting until the voltage reaches the specified level for the tuner model.
3. Pressing the MENU button saves the adjustment data.
- Inject SSG signal 38.95 MHz to IF Tuner output (sanyo tuner 115-B-8054EP and samsung tuner TECC2949PG40J (P) use signal 39.04 MHz). - Access to factory mode setting. - Adjust IF coarse until we got In Low or In High position. - Select IF Fine menu. - Adjust IF Fine tuner until we got AFC Ok from AFC In low condition or AFC In High. - If adjustment from AFC In Low , then turn up IF fine until 10 steps at above of Blinking between In Low/Ok. - If adjustment from AFC In High , then turn down IF tuner until 10 steps at the bottom of Blinking between In High/Ok. - Press MENU button to keep adjustment data.
c.2. AGC Adjustment : :
- Inject normal pattern ( channel 7 ) with signal strength 60dB on antenna input. - Select AGC menu on Factory Mode. - Monitor AGC voltage of Test Point TP AGC at : J322 for BM3 or; J107F for BM1 or; J105 for BM0, BMI, BMJ and BML - Adjust AGC until present voltage of TP AGC around : a. Tuner Philips UV1355/AL2 tuner show voltage around 2.6 ± 0.1V (for RF 60dB ±1dB), use adjustment range 0 - 63. b. Tuner Samsung TECC2949VG33E tuner show voltage around = 3.6 ± 0.1V (for RF60dB ± 1dB), use adjustment range 192 - 255. c. Tuner Samsung TECC2949PG40J(P) tuner show voltage around 3.4V ± 0.1V (for RF 60dB ± 1dB), use adjustment range 0 - 63. d. Tuner Sanyo 115-B-8054EP tuner show voltage around 2.9 ± 0.1V (for RF 60dB ±1dB), use adjustment range 0-63. e. Tuner GDC EWT-5V3SA1-E07W, EWT-5V3SB1-E07W and EWT- 5V3SB1-E07W-1tuner show voltage around 2.7 ± 0.1V (for RF 60dB ± 1dB), use adjustment range 0-63. f. Tuner LG TAEW-G014D tuner show voltage around 2.6 ± 0.1V (for RF 60dB ± 1dB) use Adjustment range 0-63. - Press MENU button to keep adjustment data.