Professional Documents
Culture Documents
Flexi WCDMA BTS Optional Items Description
Flexi WCDMA BTS Optional Items Description
DN7086754
Issue 8-2 en
30/04/2009
1 (83)
The information in this document is subject to change without notice and describes only the
product defined in the introduction of this documentation. This documentation is intended for the
use of Nokia Siemens Networks customers only for the purposes of the agreement under which
the document is submitted, and no part of it may be used, reproduced, modified or transmitted in
any form or means without the prior written permission of Nokia Siemens Networks. The
documentation has been prepared to be used by professional and properly trained personnel,
and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes
customer comments as part of the process of continuous development and improvement of the
documentation.
The information or statements given in this documentation concerning the suitability, capacity, or
performance of the mentioned hardware or software products are given as is and all liability
arising in connection with such hardware or software products shall be defined conclusively and
finally in a separate agreement between Nokia Siemens Networks and the customer. However,
Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions
contained in the document are adequate and free of material errors and omissions. Nokia
Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which
may not be covered by the document.
Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO
EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS
DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL,
DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT
NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS
OPPORTUNITY OR DATA, THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE
INFORMATION IN IT.
This documentation and the product it describes are considered protected by copyrights and
other intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of
Nokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective owners,
and they are mentioned for identification purposes only.
Copyright Nokia Siemens Networks 2009. All rights reserved.
2 (83)
DN7086754
Issue 8-2 en
30/04/2009
Contents
Contents
Contents 3
Summary of changes 5
1
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) description 7
Flexi Mounting Covers for Back and Front (FMCA and FMCB)
description 23
7
7.1
7.2
7.3
9.4
10
10.1
10.2
10.3
10.4
11
12
12.1
12.2
12.3
Flexi
FCIA
FCIA
FCIA
13
13.1
9.1
9.2
9.3
DN7086754
Issue 8-2 en
30/04/2009
27
44
3 (83)
4 (83)
13.2
13.3
14
14.1
14.2
15
15.1
15.2
15.3
16
16.1
16.2
17
17.1
17.2
17.3
18
60
71
74
DN7086754
Issue 8-2 en
30/04/2009
Summary of changes
Summary of changes
DN7086754
Issue 8-2 en
30/04/2009
5 (83)
6 (83)
DN7086754
Issue 8-2 en
30/04/2009
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) description
In floor mounting, the plinth is fixed directly onto the floor. To meet
the Telcordia GR-63-CORE Vibrational requirements for earthquake
Zone 4 requirement, the maximum number of modules in a stack is
five (maximum total height 15 U). To meet the Telcordia GR-63CORE Vibrational requirements for earthquake Zone 2 requirement,
the maximum number of modules in a stack is nine (maximum total
height 22 U).
In wall mounting, the plinth is fixed onto the wall either by using
adapter mechanics or directly to the wall. The maximum number of
modules per plinth is two.
In pole mounting, the plinth is fixed onto a pole mounting kit (VMPB
or FPKA) by using adapter mechanics. Adapters are needed to
reduce the influence of non-parallel surfaces of the mounting
brackets. The maximum number of modules per plinth is two.
The FMFA delivery includes two fixing plates for the casings. Used in
pole and wall installations, the plates are attached across two
module casings on both sides of the modules.
See the following figure for an isometric view of the FMFA.
DN7086754
Issue 8-2 en
30/04/2009
7 (83)
DN7082497
Figure 1.
DN7099438
Figure 2.
8 (83)
Adapter mechanics
DN7086754
Issue 8-2 en
30/04/2009
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) description
The plinth has a back stop that prevents installing the BTS too near to a
wall (40 mm).
The compartment behind the front panel of the plinth is used as a storage
place, for example, for seal caps.
FMFA dimensions and weight
The dimensions and weight of the FMFA are presented in the following
table.
Table 1.
Property
Value
Height
69 mm
(2.7 in.)
Width
455 mm
(17.9 in.)
Depth
459 mm
(18.1 in.)
Weight
DN7086754
Issue 8-2 en
30/04/2009
9 (83)
See the following figure for the external fixing interfaces of the FMFA.
Casing locking
points
ESD Stud
Modules grounding
Anchoring points
to floor
DN7082504
Figure 3.
10 (83)
DN7086754
Issue 8-2 en
30/04/2009
DN70415461
Figure 4.
See the following table for the delivery contents of the VMPB.
Table 2.
DN7086754
Issue 8-2 en
30/04/2009
Delivery contents
Item
Quantity
Mounting blocks
2 pcs
M8x25 bolts
8 pcs
M10x120 bolts
4 pcs
M10x200 bolts
4 pcs
M10x300 bolts
4 pcs
Washers
4 pcs
11 (83)
See the following table for dimensions and weight of the VMPB.
Table 3.
Property
Value
Height
60 mm (2.4 in.)
Width
Depth
300 mm (11.8)
Weight
12 (83)
DN7086754
Issue 8-2 en
30/04/2009
DN7086754
Issue 8-2 en
30/04/2009
13 (83)
DN70449903
Figure 5.
14 (83)
DN7086754
Issue 8-2 en
30/04/2009
The pole can between 60 mm (2.4 in.) and 120 mm (4.7 in.) in diameter.
There are two sets of fixing points on the installation plate. The FPIA can
carry the weight of 5 kg (11 lbs).
For the FPIA delivery contents, see section Contents of the Flexi Pole
Installation Kit (FPIA) delivery in the Installing Flexi WCDMA BTS Optional
Items document.
DN7086754
Issue 8-2 en
30/04/2009
15 (83)
DN70458657
Figure 6.
16 (83)
DN7086754
Issue 8-2 en
30/04/2009
Bolt M8x20
Fixingpoints
64mm (2.5 in.)
Bolt M10X120
105 mm thread
Fixingpoints
184mm (7.2 in.)
Figure 7.
The width of the fixing points is 184 mm (7.2 in.) and 64 mm (2.5in.). There
are fixing points in three sides of the FPKA. The M10 screws should be
tightened to 30 Nm and the M8 screws to 20 Nm. The FPKA can carry the
maximum weight of 160 kg (352.7 lbs).
The delivery contents of the FPKA are listed in the following table.
DN7086754
Issue 8-2 en
30/04/2009
17 (83)
Table 4.
Item
Quantity
FPKA Bracket
1 pcs.
Bolt M8 x 20
6 pcs.
Bolt restrainer
2 pcs.
1 pcs.
2 pcs.
18 (83)
DN7086754
Issue 8-2 en
30/04/2009
Figure 8.
DN7086754
Issue 8-2 en
30/04/2009
19 (83)
DN70424752
Figure 9.
20 (83)
DN7086754
Issue 8-2 en
30/04/2009
DN70424776
Figure 10.
DN7086754
Issue 8-2 en
30/04/2009
21 (83)
22 (83)
DN7086754
Issue 8-2 en
30/04/2009
Flexi Mounting Covers for Back and Front (FMCA and FMCB)
description
DN7086754
Issue 8-2 en
30/04/2009
23 (83)
Front cover
Back cover
2 x safety catch
Grounding cable
DN7082516
Figure 11.
FMCA dimensions
The dimensions of the FMCA are presented in the following table.
Table 5.
Property
Front cover
Back cover
Height
128 mm
128 mm
(5 in.)
(5 in.)
492 mm
446 mm
(19.4 in.)
(17.6 in.)
100 mm
37 mm
(3.9 in.)
(1.5 in.)
Width
Depth
24 (83)
DN7086754
Issue 8-2 en
30/04/2009
Flexi Mounting Covers for Back and Front (FMCA and FMCB)
description
Table 6.
Property
Front cover
Back cover
Height
83 mm
83 mm
(3.3 in.)
(3.3 in.)
492 mm
446 mm
(19.4 in.)
(17.6 in.)
100 mm
37 mm
(3.9 in.)
(1.5 in.)
Width
Depth
Table 7.
DN7086754
Issue 8-2 en
30/04/2009
Grounding cable
Property
Value
Length
Thickness
16 mm2 (5 AWG)
25 (83)
26 (83)
DN7086754
Issue 8-2 en
30/04/2009
7
7.1
7.2
DN7086754
Issue 8-2 en
30/04/2009
27 (83)
Table 8.
FSEB dimensions
Property
Value
Width
335 mm
(13.2 in.)
Height
94 mm
(3.7 in.)
Depth
182 mm
(7.2 in.)
Weight
Max. 2 kg
(4.4 lbs)
7.3
28 (83)
DN7086754
Issue 8-2 en
30/04/2009
ESD
Grounding point
EAC M16
UltraSite and Talk
swap cases
BTS interconnection
cable
DN70283679
Figure 12.
FSEB interfaces
PWB interface
The PWB interface and connectors are presented in the table below.
Table 9.
Interface
Type
Description
EACX-I
Sub-D37, female
6 alarm outputs
(ESM extension,
compatible to EAC on
ESM)
EACX-S
10 SMDK1/6-3.5
DN7086754
Issue 8-2 en
30/04/2009
Screw terminal
ESM
Sub-D37, male
29 (83)
Table 9.
Interface
Type
Description
*EACX-II
Sub-D37, female
Smoke-Detector
Power X4114
EACX-II(D37)
EACX-I(D37)
Not in use
DN70410509
Figure 13.
30 (83)
FSEB PWB
DN7086754
Issue 8-2 en
30/04/2009
DN70154491
Figure 14.
DN7086754
Issue 8-2 en
30/04/2009
31 (83)
See the following figures for the internal and external wiring of the FSEC.
Internal wiring (factory cabling) version 6Yxxxxxxxxx
FSEC
VAL-MS VAL-MS
60 ST 60 ST
PE
PE
Electrical connection
GND
PE
0V (+)
-48 V
DN70592401
Figure 15.
32 (83)
DN7086754
Issue 8-2 en
30/04/2009
VAL-MS VAL-MS
60 ST 60 ST
PE
PE
Cable
shield
DC cable type:
MCCMK/MCMK
(or equivalent)
System/RF Module
To other
FSEC
DN70592413
Figure 16.
FSEC dimensions
The dimensions of the Flexi system external OVP box are presented in the
following table. The FSEC is made of aluminium.
DN7086754
Issue 8-2 en
30/04/2009
33 (83)
Table 10.
FSEC dimensions
Property
Value
Width
95 mm
(3.7 in.)
Height
155 mm
(6.1 in.)
Depth
155 mm
(6.1 in.)
Weight
2.7 kg
(5.9 lbs)
FSEC connectors
In the FSEC, there are screw terminals for input and output cables. There
are four pieces of screw terminals for AWG 2 cables and for earthing two
PEs (protective earthing GND) terminals for AWG 2 cable size. A 2-meter
DC cable is included in the FSEC delivery.
34 (83)
DN7086754
Issue 8-2 en
30/04/2009
9
9.1
Flexi Power Module (FPMA) and submodules (FPAA and FPBA) description
Flexi Power Module (FPMA) and sub-modules
(FPAA and FPBA) operation
Flexi Power Module (FPMA) is an optional module. It comprises FPMA
mechanics and AC and DC interfaces. The actual power sub-modules are
the following:
.
DN7086754
Issue 8-2 en
30/04/2009
35 (83)
Type label
DN70230045
Figure 17.
DN7084386
Figure 18.
36 (83)
DN7086754
Issue 8-2 en
30/04/2009
The FPMA can support 1-phase and 3-phase AC input. The nominal input
voltage is 200-240 V AC (the operating voltage range is 180 - 276 V AC).
The maximum output power from the FPMA is 4kW (with 4 FPAAs).
Flexi Power AC-DC sub-module (FPAA)
The main function of the FPAA is to provide the BTS with nominal 48 V DC
power from an AC supply. Maximum DC output power of one FPAA
module is 1000 W. A nominal 48 V DC supply is intended for BTS internal
use only (a nominal 48 V DC supply is not intended for 3rd party
equipment because they may require lower conducted emission level than
EN55022 Class A). The FPAA includes its own integrated self-controlled
fan. In case the fan fails, an alarm is generated and the FPAA has to be
replaced (the fan alone cannot be replaced).
Caution
Risk of thermal runaway of the battery, because temperature
compensation of charging voltage is not supported. Do not connect an
external lead acid battery for longer backup times to a nominal 48 V DC
supply.
9.2
DN7086754
Issue 8-2 en
30/04/2009
37 (83)
Table 11.
Property
FPMA
Height
133 mm/3 U
(5.2 in.)
Width
447 mm
(17.6 in.)
422 mm
(16.6 in.)
560 mm
(22.1 in.)
Weight (empty)
< 11 kg
(< 24.3 lbs)
9.3
Weight
28 kg
(61.9 lbs)
Table 12.
Connector
Type
Purpose
Power supply in
Terminal block
Grounding
2 x M5
Module grounding
38 (83)
DN7086754
Issue 8-2 en
30/04/2009
Table 13.
Connector
Type
Purpose
AC cable connector
Mate-N-Lock
AC input
DC connector
DC output
Alarm connector
2 x RJ-45*
Alarms**
tri-colour LED
*for chaining
**Alarm 1 (AL01): AC input failure (alarm is sent when AC input voltage is
missing or it is out of range).
**Alarm 2 (AL02): maintenance needed (possible reasons are unit failure,
cooling fan failure, output power is low or over temperature shut down is
ON).
FPBA front panel connectors
There is a stand-by switch on the front panel of the FPBA.
The connectors on the FPBA front panel, their types and purposes are
listed in the table below.
Table 14.
Connector
Type
Purpose
DC input/output connector
DN7086754
Issue 8-2 en
30/04/2009
39 (83)
Table 14.
Connector
Type
Purpose
Alarm connector
2 x RJ-45*
Alarms**
tri-colour LED
*for chaining
**Alarm 2 (AL02): maintenance needed (possible reasons are unit failure,
output power is low or unit has reached end of it's life).
**Unit has an input for Alarm 1 (AL01) from FPAA unit (Alarm 1 is a trigger
for battery discharging).
9.4
Table 15.
Colour
Explanation
Yellow
Green
Normal operation
Red
Alarm or fault
Red, blinking
See the following figure for the location of the FPAA LED.
40 (83)
DN7086754
Issue 8-2 en
30/04/2009
LED
DN70350654
Figure 19.
FPAA LED
Table 16.
Colour
Explanation
Yellow
Ggreen
Charging
Discharging
Minor alarm
Red
DN7086754
Issue 8-2 en
30/04/2009
41 (83)
LED
DN70350678
Figure 20.
42 (83)
FPBA LED
DN7086754
Issue 8-2 en
30/04/2009
10
10.1
Caution
Risk of thermal runaway of the battery, because temperature
compensation of charging voltage is not supported. Do not connect an
external lead acid battery for longer backup times to the 53-55 V DC
supply.
The FPDA includes its own integrated self-controlled fan. In case the fan
fails, an alarm is generated and the fan has to be replaced.
For installation instructions, see section Installing Flexi Power DC/DC
Module 24V FPDA in the Installing Flexi WCDMA BTS Optional Items
document.
The FPDA is presented in the following figure.
DN7086754
Issue 8-2 en
30/04/2009
43 (83)
DN70150502
Figure 21.
10.2
Table 17.
Property
Value
Height
90 mm (2U)
(3.5 in.)
Width
447 mm
(17.6 in.)
422 mm
(16.6 in.)
560 mm
(22.1 in.)
44 (83)
DN7086754
Issue 8-2 en
30/04/2009
Table 17.
Property
Value
Weight
< 15 kg
(< 33.1 lbs)
10.3
Table 18.
Connector
Connector type
Purpose
Input connector
M10 bolts
DC input
Output connector
M10 bolts
DC output
Alarm connectors
2 x RJ-45*
Alarms**
*for chaining
**Alarm 1 (AL01): DC input failure (alarm is sent when DC input voltage is
missing or it is out of range).
**Alarm 2 (AL02): maintenance needed (possible reasons are unit failure,
cooling fan failure, output power is low or over temperature shut down is
ON).
The FPDA front panel is presented in the following figure.
DN7086754
Issue 8-2 en
30/04/2009
45 (83)
DC Input cabling
Alarm cabling
DC Output cabling
LED
GND
DN70141402
Figure 22.
10.4
Table 19.
46 (83)
Colour
Explanation
Green
Normal operation
Red
Alarm or fault
Yellow
Stand-by
Red, blinking
DN7086754
Issue 8-2 en
30/04/2009
11
LED
DN70265249
Figure 23.
DN7086754
Issue 8-2 en
30/04/2009
47 (83)
Table 20.
Property
Value
90 - 276 V AC
Output voltage
56 V DC at 500 W
AC input
(row connector)
DC output
(multi-beam connector)
DN70407333
Figure 24.
FPAB connectors
See the following figure for installing the FPAB in the RF Module.
48 (83)
DN7086754
Issue 8-2 en
30/04/2009
DN70286831
Figure 25.
FPAB dimensions
The dimensions of the FPAB are presented in the following table.
Table 21.
DN7086754
Issue 8-2 en
30/04/2009
FPAB dimensions
Property
Value
Width
Height
73 mm (2.9 in.)
Depth
Weight
49 (83)
Table 22.
50 (83)
Colour
Explanation
Yellow
Green
Normal operation
DN7086754
Issue 8-2 en
30/04/2009
12
12.1
DN7086754
Issue 8-2 en
30/04/2009
51 (83)
DN70253985
Figure 26.
12.2
FCIA cabinet
52 (83)
DN7086754
Issue 8-2 en
30/04/2009
one power distribution unit (WPU) with one control unit (CU), and
The power distribution unit mainly distributes the input AC mains to the
rectifier units. The control unit controls the rectifier power units and
monitors the alarms in the event of low supply voltage, or if the MIBBU
enters the battery backup mode in the event of an AC mains failure. The
alarm generated by the control unit is forwarded to the BTS O&M software.
Flexi Power Rectifier (FPRx)
The Flexi Rectifier Module (FPRA) is a modular 6kW output power AC
rectifier package made up of three individual 2kW AC/DC power modules
operating in a parallel mode configuration. The FPRA outputs a positive
earthed 54VDC (V48N) as a respective BTS operational supply voltage
rail and for site battery charging. It supports 2G and 3G Flexi BTS
configurations (indoor and outdoor cabinets, and stack, pole and wall
configurations).
Flexi Battery Mounting Kit for FCIA (FMBB)
Flexi Battery Mounting Kit (FMBB) is needed when using batteries or the
MIBBU solution in FCIA. The mounting kit is installed at the bottom of the
cabinet.
12.3
DN7086754
Issue 8-2 en
30/04/2009
53 (83)
Table 23.
Property
Value
Height
1800 mm / 40.5U
(70.87 in.)
Width
600 mm
(23.62 in.)
Depth
600 mm
(23.62 in.)
54 (83)
Weight
62 kg
(empty cabinet)
(136 lbs.)
36 U
DN7086754
Issue 8-2 en
30/04/2009
13
13.1
it houses the Flexi cabinet site support module (FCSA) that provides
long-term battery back-up and a 4U-high IP55-protected space for
Line Terminal Equipment (LTE)
together with Flexi cabinet air filter (FCFA), it protects the BTS in
extremely dirty conditions
DN7086754
Issue 8-2 en
30/04/2009
55 (83)
DN70138414
Figure 27.
13.2
FCOA cabinet
56 (83)
DN7086754
Issue 8-2 en
30/04/2009
The air filter is installed in the back of the cabinet, replacing the original
back wall. It consists of a filter element, 8 x diagonal fans, a pressure
sensor, a control logic, and back wall mechanics. The wind plate is
installed in the cabinet door.
The control of the FCFA fans is based on a pressure sensor. The pressure
sensor measures pressure inside the cabinet and this information is then
used for controlling the fan speed.
The air filter is presented in the following figure.
DN70150526
Figure 28.
DN7086754
Issue 8-2 en
30/04/2009
Air filter
57 (83)
58 (83)
DN7086754
Issue 8-2 en
30/04/2009
Heat
Exchanger
MIBBU
Control
card
LTE Space
Batteries
FMBA
DN70150538
Figure 29.
Site support
DN7086754
Issue 8-2 en
30/04/2009
59 (83)
DN70150541
Figure 30.
Fire detector
13.3
60 (83)
DN7086754
Issue 8-2 en
30/04/2009
Table 24.
Property
Value
Height
1550 mm
(61 in.)
Width
770 mm
(30.3 in.)
Depth
770 mm
(30.3 in.)
930 mm
(36.6 in.)
1020 mm
(40.2 in.)
Weight
Max. 80 kg
(empty cabinet)
(177 lbs)
Weight
104 kg
(230 lbs)
Weight
110 kg
(243 lbs)
Total weight
365 kg
(807 lbs)
40 U
(30 U horizontally + 5 U + 5 U vertically
DN7086754
Issue 8-2 en
30/04/2009
21 U
61 (83)
62 (83)
DN7086754
Issue 8-2 en
30/04/2009
14
14.1
DN7086754
Issue 8-2 en
30/04/2009
63 (83)
DN70324735
Figure 31.
64 (83)
DN7086754
Issue 8-2 en
30/04/2009
DN70324723
Figure 32.
The FMSA provides installation space for up to any two Flexi 3U modules
and the plinth (6U in total). It is installed on a pole or wall.
The FMSB provides space for up to any six Flexi 3U modules and the
plinth (18U in total). It is installed on the floor.
DN7086754
Issue 8-2 en
30/04/2009
65 (83)
14.2
Table 25.
Property
Value
Height
Width
Depth
Weight (empty)
12 kg (26.5 lbs.)
6U
Table 26.
66 (83)
Property
Value
Height
Width
Depth
Weight (empty)
21 kg (46.3 lbs.)
18U
DN7086754
Issue 8-2 en
30/04/2009
15
15.1
DN7086754
Issue 8-2 en
30/04/2009
67 (83)
2G
System
Module
1 U free space
RF Module
DN7082146
Figure 33.
Tip
The example RF Modules shown in the figure are Dual RF Modules.
Before the mounting kit can be installed, the following parts are removed
from the lower half of the GSM/EDGE UltraSite cabinet:
68 (83)
3 x fans
DN7086754
Issue 8-2 en
30/04/2009
The mounting kit consists of one dual rack in which one System Module
and one RF Module are installed, one single rack for the second RF
Module installation, and cables. There is a remaining space of 1 U in the
single rack when the RF Module is installed.
For installation instructions, see section Overview of installing modules in
cabinet with Flexi Mounting Kit Vertical for 2G in the Installing Flexi
WCDMA BTS Modules in Cabinets document.
15.2
DN7086754
Issue 8-2 en
30/04/2009
69 (83)
Dual rack
FRONT
BACK
Single rack
FRONT
BACK
DN7082037
Figure 34.
70 (83)
DN7086754
Issue 8-2 en
30/04/2009
15.3
Dual rack
Single rack
Height
694 mm
585 mm
(27.3 in.)
(23 in.)
302 mm
196 mm
(11.9 in.)
(7.7 in.)
395 mm
400 mm
(15.6 in.)
(15.8 in.)
6.2 kg
4.6 kg
(13.7 lbs)
(10.2 lbs)
0.7dB
0.7dB
Width
Depth
Weight
DN7086754
Issue 8-2 en
30/04/2009
71 (83)
72 (83)
DN7086754
Issue 8-2 en
30/04/2009
16
16.1
DN7086754
Issue 8-2 en
30/04/2009
73 (83)
DN70231874
Figure 35.
The mounting kit consists of a rack in which, for example, one WCDMA
System Module, up to three WCDMA RF Modules and one FPMA or
System Extension Module or FPDA are installed, and cables. The space
requirement for 5 x 3U modules is 15U.
For installation instructions, see section Installing modules in cabinet with
Flexi Mounting Kit Horizontal for 2G in the Installing Flexi WCDMA BTS
Modules in Cabinets document.
16.2
74 (83)
DN7086754
Issue 8-2 en
30/04/2009
Property
FMUB
Height
Width
Depth
Weight
(cables excluded)
The loss of RF cables
DN7086754
Issue 8-2 en
30/04/2009
0.7dB
75 (83)
76 (83)
DN7086754
Issue 8-2 en
30/04/2009
17
17.1
Figure 36.
The I-HSPA Adapter can be fitted to a Flexi BTS 2U module casing. When
used with the Flexi BTS module casing, the I-HSPA Adapter can be
installed with the Flexi WCDMA BTS in stand-alone configurations, such
as free-standing, wall mounted or pole mounted.
DN7086754
Issue 8-2 en
30/04/2009
77 (83)
Rear Cover
Casing
Front Cover
DN70287651
Figure 37.
The I-HSPA Adapter uses forced air cooling based on fresh air intake from
back to front. This allows it be installed either horizontally or vertically. The
contents of the I-HSPA Adapter delivery also include an air-blocking plate,
to be used if the I-HSPA Adapter is with the Flexi BTS 2U module casing.
The I-HSPA Adapter features a lightweight aluminium alloy casing with
stainless steel alloy used for the fan carrier.
Figure 38.
78 (83)
DN7086754
Issue 8-2 en
30/04/2009
17.2
Table 27.
Height
43 mm
299 mm
4.7 kg
Table 28.
17.3
Width
Height
84.05 mm
Depth
395 mm
Weight
10.6 kg
Table 29.
DN7086754
Issue 8-2 en
30/04/2009
Front panel
identifier
Purpose
Interface type
External transport
EIF2 (TRS/LMT)
External transport/
Local Management
Terminal
Connector Type
RJ45 shielded
79 (83)
Table 29.
Front panel
identifier
Purpose
Interface type
Connector Type
EIF3 (TRS)
External transport
RJ45 shielded
EIF4
BTS interface
RJ45 shielded
DC IN
48VDC Power
Input
DC IN
DN70282859
Figure 39.
80 (83)
Multi-Beam XL RA
2 pin
EIF1
EIF2
EIF3
EIF4
DN7086754
Issue 8-2 en
30/04/2009
18
DN7086754
Issue 8-2 en
30/04/2009
81 (83)
Door
proximity
bracket 1)
Figure 40.
82 (83)
DN7086754
Issue 8-2 en
30/04/2009
Citytalk cabinet
and roof 2)
Back wall
Rack plinth 1)
Standoff proximity bracket 1)
Lock cylinder 2)
Lock cover 1)
Figure 41.
DN7086754
Issue 8-2 en
30/04/2009
83 (83)