Professional Documents
Culture Documents
Ericsson and Huawei
Ericsson and Huawei
Ericsson and Huawei
Revision
Remark
12/18/2008
1.0
Initial revision
1/10/2008
1.1
BQ HO tuning
Changes
Paramter
Old Value
18
12
18
12
AMR ACS(H)
13001101
3s
No Dl.MR HO Allowed
No
RscPenaltyTimer
UmPenaltyTimer
DLQuaLimitAMRFR
50
DLQuaLimitAMRFH
50
ULQuaLimitAMRFR
50
ULQuaLimitAMRFH
50
No Dl Mr.HO Allowed
Yes
New Value
0
4
3
31
23
2
2
33
29
21010101
2s
4
4
Yes
5
10
60
60
60
60
No
Parameter Name
Object Name
HW setting
range
HW default
value
Ericsson
cell specific
cell specific
No
Yes
No
Yes
62
63
DL DTX
No
Yes
Encryption Algorithm
A5/0A5/2
DL PC Allowed
Yes
Yes
UL PC Allowed
Yes
Yes
Direct Retry
Yes
Yes
No
No
RXLEV_ACCESS_MIN
Yes
Yes
UL DTX
Shall Use
PT(s)
Idle Mode
TO
Idle Mode
0-7
ACS
Idle Mode
Yes,No
No
No
CRO(2dB)
Idle Mode
063
cell specific
Cell_Bar_Qualify
Idle Mode
01
No
PI
Idle Mode
Yes, No
Yes
Yes
CRH
Idle Mode
014
6dB
6dB
0255
20
50
BS-PA-MFRAMS
Idle Mode
29
2 Multiframe Pe 2 Multiframe P
BS_AG_BLKS_RES
Idle Mode
NCC Permitted
Idle Mode
Selection of 7 P 11111111
11111111
Cell_Bar_Access
Idle Mode
01
3-12141620253250
32
50
ATT
Idle Mode
Yes, No
Yes
Yes
Call Control
03
Call Control
015
15
15
Call Control
015
Call Control
015
Call Control
063
63
63
Call Control
063
26
31
Call Control
063
16
23
Call Control
015
15
15
Call Control
015
Call Control
015
Call Control
063
63
63
Call Control
063
56
33
Call Control
063
53
29
AMR ACS(H)
Call Control
010101
Call Control
03
Call Control
015
Call Control
015
Call Control
015
Call Control
063
30
40
Call Control
063
22
28
Call Control
063
16
20
Call Control
015
Call Control
015
Call Control
015
Call Control
063
55
40
Call Control
063
46
28
Call Control
063
28
20
AMR ACS(F)
Call Control
11100100
Call Control
0-3
Call Control
Call Control
YesNo
No
No
Call Control
YesNo
No
No
Call Control
Yes,No
No
No
Yes,No
No
No
Allow EMLPP
Call Control
Yes,No
No
No
Allow Reassign
Call Control
Yes,No
Yes
Yes
Call Control
0-7
Call Control
0-7
Call Control
03
Call Control
0-15
Call Control
07
Call Control
07
Call Control
07
Call Control
07
Call Control
07
Call Control
07
Qsearch C
Call Control
0-15
15
15
Scale Order
Call Control
+0dB
Call Control
Yes,No
No
No
3G Search PRIO
Call Control
Yes, No
Yes
Yes
Qsearch P
Call Control
0-15
15
15
FDD Qmin
Call Control
07
Call Control
0-3
Call Control
Ec/No, RSCP
RSCP
RSCP
FDD Q Offset
Call Control
015
Qsearch C Initial
Call Control
Qsearch I
Call Control
0-15
15
15
Call Control
0-3
Power Deviation(2dB)
Call Control
03
Call Control
Yes,No
Yes
Yes
MBR
Call Control
0-3
02
ECSC
Call Control
Yes,No
No
Yes
464
52
20
Call Control
Yes,No
No
No
Call Control
00000
Call Control
Level0 Forbidden0000000000
0000000000
MS MAX Retrans
Call Control
1247
2 Times
4 Times
Call Control
15
Call Control
0-254 (ms)
Call Control
YesNo
No
No
Call Control
34254
34
34
Call Control
29254
29
29
N200 of SDCCH
Call Control
23254
23
23
N200 of SACCH
Call Control
5254
N200 of Release
Call Control
5254
N200 of Establish
Call Control
5254
Call Control
YesNo
No
No
Call Control
1-255
60
60
Call Control
1-255
60
60
Call Control
1-255
200
200
Call Control
1-255
150
150
T200 FACCH/H(5ms)
Call Control
1-255
50
50
T200 FACCH/F(5ms)
Call Control
1-255
50
50
T200 SDCCH(5ms)
Call Control
1-255
60
60
Call Control
-121-47
-115
-110
Call Control
0255
180
180
Call Control
Speech Version
Call Control
001011
101111
464
12
20
464
15
20
063
32
20
063
48
20
0100
85
70
Call Control
Call Control
Yes,No
Paging Times
Call Control
Call Control
063
16
16
0-63
31
20
No
Disable
T3105(10ms)
30
45
No
No
50
50
25
25
Preference for
2G Cell,
Preference for
Handover Control 3G Cell,
Preference for
2G By
Threshold
68
68
30
63
10
10
80
80
63
63
63
63
90
90
25
25
30
30
10
Yes
Cell specific
No
Cell specific
10
10
10
10
90
90
85
80
Yes
No
No
Yes
20
50
No
No
35
50
50
25
25
Preference for
Handover Control 063
2G Cell,
Preference for
Handover Control 3G Cell,
Preference for
Handover Control 2G By
Threshold
Handover Control
35
25
25
ReceiveQualThrshAMRHR
Handover Control
60
60
ReceiveQualThrshAMRFR
Handover Control
65
50
90
90/cell specifi
85
60
20
cell specific
10
10
40
40
15
No: dual-timesloYes
35
cell specific
25
cell specific
61
No
No
63
61
Assign-optimum-level Threshold
40
cell specific
UO HO Valid Time(s)
UO HO Watch Time(s)
TA Hysteresis
TA Threshold
63
61 / cell specif
RX_QUAL Threshold
RX_LEV Hysteresis
RX_LEV Threshold
TA for UO HO Allowed
Yes
No
No
No
OL to UL HO Allowed
No
Yes
UL to OL HO Allowed
Yes
Yes
Handover Control
80
80
K Bias
35
25
40
30
20
20
15
15
10
10
Load HO Bandwidth
25
25
75
70
Load HO Threshold
85
90
10
10
ULQuaLimitAMRHR
60
60
DLQuaLimitAMRHR
60
60
ULQuaLimitAMRFR
65
60
DLQuaLimitAMRFR
65
60
RXLEVOff
RXQUAL12
50
40
RXQUAL11
51
41
RXQUAL10
52
42
RXQUAL9
53
43
RXQUAL8
54
44
RXQUAL7
55
45
RXQUAL6
56
46
RXQUAL5
57
47
RXQUAL4
58
48
RXQUAL3
59
49
RXQUAL2
60
50
RXQUAL1
70
60
60
55
No Dl Mr.HO Allowed
No
No
Filter Parameter B
Filter Parameter A8
10
10
Filter Parameter A7
10
10
Filter Parameter A6
10
10
Filter Parameter A5
10
10
Filter Parameter A4
10
10
Filter Parameter A3
10
10
Filter Parameter A2
10
10
Filter Parameter A1
10
10
UL Qual. Threshold
60
60
DL Qual. Threshold
60
60
TA Threshold
63
61
DtxMeasUsed
Handover Control
Open
Open
CfgPenaltyTimer
255
255
UmPenaltyTimer
10
10
RscPenaltyTimer
30
30
30
10
63
63
15
63
30
63
Handover Control
Yes
Yes
Transfer Original MR
No
No
MR.Preprocessing
No
No
No
No
Penalty Allowed
Yes
Yes
No
No
ATCBHoSwitch
Open
Close
Handover Control
Handover Control
Yes
NO
H2F HO th
25
10
F2H HO th
25
20
Yes
Yes
Handover Control
Handover Control
Inter-layer HO Hysteresis
Inter-layer HO Threshold
25
30
Outgoing-RAT HO Allowed
No
No
Handover Control
Handover Control
3
16
8
0
10
cell specific
20
10
Interference HO Allowed
Yes
Yes
No
cell specific
TA HO Allowed
Yes
Yes
BQ HO Allowed
Yes
Yes
Fringe HO Allowed
Yes
Yes
Level HO Allowed
PBGT HO Allowed
Yes
Yes
Rx_Level_Drop HO Allowed
No
No
No
No
Load HO Allowed
No
No
Intracell HO Allowed
No
No
SDCCH HO Allowed
No
No
Co-BSC/MSC Adj
Yes
Yes
Power Control
0255
53
Power Control
0255
50
Power Control
0255
47
Power Control
0255
43
Power Control
0255
40
Power Control
0255
30
Power Control
0255
20
Power Control
0255
Power Control
139
Power Control
138
No
136
12
14
137
16
14
135
12
12
134
16
12
132
16
20
133
22
20
131
16
18
130
22
18
Power Control
063
20
18
Power Control
063
30
18
Power Control
010
Power Control
010
Power Control
120
Power Control
120
019
Power Control
019
Power Control
130
Power Control
130
130
12
14
130
16
14
130
12
12
130
16
12
130
16
20
130
22
20
130
16
18
130
22
18
063
25
18
Power Control
Power Control
063
35
18
Power Control
010
Power Control
010
Power Control
120
Power Control
120
019
Power Control
019
010
05
0255
0255
Power Control
1255
Power Control
116
16
16
Power Control
063
Power Control
07
Power Control
063
Power Control
07
Power Control
Power Control
16
16
Power Control
Power Control
Power Control
Power Control
30
25
Power Control
40
35
Power Control
Power Control
Power Control
30
25
Power Control
40
25
Power Control
03
Power Control
03
Power Control
Yes,No
Yes
Yes
Power Control
120
Power Control
120
Power Control
120
Power Control
120
AMR PC Interval
Power Control
115
BTS PC Class
Power Control
116
16
16
Power Control
Power Control
Power Control
Power Control
0-7
Power Control
032
Power Control
032
16
16
Power Control
04
Power Control
030
Power Control
030
Power Control
030
Power Control
03
Power Control
0-3
Power Control
Yes,No
Yes
Yes
Power Control
120
07
Power Control
120
Power Control
120
Power Control
120
Power Control
Power Control
07
Power Control
07
Power Control
063
25
25
Power Control
063
35
25
Power Control
0-7
Power Control
0-7
Power Control
25
25
Power Control
35
25
PC Interval
Power Control
115
90
No
Channel Management
95
Yes
Yes
50
50
50
cell specific
No
Close
No
Close
Fix Abis Prior Choose Abis Load Thred(%) Channel Manage 0100
80
80
80
80
Channel Management
60
40
cell specific
Yes
Yes
Channel Management
Channel Management
30
30
Interf.of DL Qual.Threshold
40
30
25
45
40
30
10
35
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Channel Management
No
Not Support
Channel Management
Quality prefer
Yes
Yes
60
60
80
cell specific
cell specific
WaitforRelIndAMRHR
Other Property
3000-34000(ms 26000
26000
WaitforRelIndAMRFR
Other Property
3000-34000(ms 34000
34000
T3103C(ms)
Other Property
500-60000
10000
10000
T3122(s)
Other Property
0255
10
10
TREESTABLISH(ms)
Other Property
500040000
15000
15000
T3111(ms)
Other Property
500-60000
1000
1000
T3109(ms)
Other Property
1000-35000
27000
30000
T8(ms)
Other Property
500-60000
10000
20000
T3121(ms)
Other Property
500-60000
10000
30000
T3107(ms)
Other Property
500-60000
10000
5000
T7(ms)
Other Property
500-60000
10000
10000
T3103A(ms)
Other Property
500-60000
10000
10000
Other Property
1000-30000
5000
5000
T3101(ms)
Other Property
500-60000
3000
3000
160
220
180
Other Property
Forced turn-on
Other Property
0, 1
Interference
Other Property
01
Yes
No
Other Property
YesNo
No
No
Other Property
Yes, No
Yes
Yes
Other Property
Yes, No
No
No
Other Property
Main/Diversity
Main/Diversity Maximum/Mean
01
01
01
01
Other Property
01
Other Property
01
Other Property
01
Other Property
01
01
Other Property
01
01
01
01
01
01
01
Other Property
01
01
Other Property
Yes, No
No
No
Other Property
160
15
15
Other Property
Yes,No
Yes
Yes
Other Property
YesNo
No
Yes
MS_TXPWR_MAX_CCH
Other Property
0-19
PWRC
Other Property
Yes, No
Yes
Yes
Included Angle(Degree)
Other Property
0-360
360
360
Other Property
0360
360
360
Other Property
065535
Other Property
Other Property
20100
80
100
Other Property
0255
15
15
Other Property
0255
10
10
Other Property
0-65535
36671
36671
Other Property
Yes, No
No
NO
5000
15
Other Property
0-12
Other Property
0-12
Other Property
09
Other Property
09
Other Property
04
0 (with tower-m 3
Other Property
065535
65535
65535
Other Property
0-21
Other Property
131
20
20
Other Property
-11548
85
48
Other Property
-11548
87
90
Other Property
-11548
92
98
Other Property
-11548
98
104
Other Property
-11548
105
108
Other Property
-11548
110
115
Other Property
0100
50
90
SMCBC DRX
Other Property
YesNo
Yes
Yes
Other Property
NT14.5K, NT12K,0001110110
111111000
Other Property
StartUp
Other Property
not report
Other Property
Yes, No
No
255
N3105_MAX
GPRS
3-10
10
10
N3103_MAX
GPRS
2-5
N3101_MAX
GPRS
GPRS
8-30
20
NotSupport,Support
GPRS
GPRS
6-120
GPRS
GPRS
6-120
6
NotSupport,Support
Not Support
Not Support
GPRS
NotSupport,Support
Not Support
Not Support
GPRS
Not Support
Not Support
GPRS
MCS6
MCS6
GPRS
UNFIXED
UNFIXED
GPRS
MCS2
MCS2
GPRS
UNFIXED
UNFIXED
BEP Period
GPRS
GPRS
0-10
IR,LA
LA
LA
GPRS
0-64
GPRS
0-64
GPRS
0-64
10
10
GPRS
0-64
GPRS
0-64
GPRS
GPRS
0-64
5
CS1,CS2,CS3,CS4
GPRS
GPRS
GPRS
Not Support
20
Not Support
NotSupport,Support
16
MCS1,MCS2,MCS3,MCS4,MCS5,MCS6,MCS7,MCS8,MCS9
MCS1,MCS2,MCS3,MCS4,MCS5,MCS6,MCS7,MCS8,MCS9,UNFIXED
MCS1,MCS2,MCS3,MCS4,MCS5,MCS6,MCS7,MCS8,MCS9
MCS1,MCS2,MCS3,MCS4,MCS5,MCS6,MCS7,MCS8,MCS9,UNFIXED
CS2
CS2
UNFIXED
UNFIXED
0-64
0-64
GPRS
0-64
10
10
GPRS
0-64
GPRS
0-64
GPRS
GPRS
0-64
5
CS1,CS2,CS3,CS4
CS1
CS2
GPRS
CS1,CS2,CS3,CS4,UNFIXED
UNFIXED
UNFIXED
GPRS
10
10
GPRS
GPRS
CS1,CS2,CS3,CS4,UNFIXED
1-3600
0-8
2
2
All dynamic channels can be pre-empted,Control channels cannot be
1-3600
20
20
Convert dynamic channel in underlaid subcell,Convert dynamic chan
Convert dynamic
Convert dynami
GPRS
10-80
80
80
GPRS
10-70
70
70
10-80
20
20
10-70
20
20
0-100
50
30
MultiBand reporting
GPRS
GPRSHCSThr
GPRS
-110dB
-110dB
0,1,2,3,4,5,6,7,nouse
PriorClass
GPRS
MsTxPwrMax
GPRS
0-31
RxLevAccMin
GPRS
ExcAcc
GPRS
0-63
2
Exclusive,NoExclusive
CellBarAccess2
GPRS
RAReselectHyst
GPRS
TResel
GPRS
GPRS
Yes or No
GPRS
0,1
Permit,NoPermit
NoExclusive
NoExclusive
Permit
Permit
2dB
2dB
10sec
10sec
Yes
Yes
0dB,2dB,4dB,6dB,8dB,10dB,12dB,14dB,nouse
5sec,10sec,15sec,20sec,30sec,60sec,120sec,300sec,nouse
c31standard,c31n c31standard
c31standard
0dB,2dB,4dB,6dB,8dB,10dB,12dB,14dB
2dB
2dB
Yes or No
No
No
Yes or No
No
No
GPRS
GPRS
GPRS
GPRS
Persistence Level 4
GPRS
1-16
6
6
0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,16,nouse
Persistence Level 3
GPRS
Persistence Level 2
GPRS
Persistence Level 1
GPRS
16
16
14
14
13
13
12
12
20
20
20
20
0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,16,nouse
0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,16,nouse
0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,16,nouse
2,3,4,5,6,7,8,9,10,12,14,16,20,25,32,50
12,15,20,30,41,55,76,109,163,217
1,2,4,7
1,2,4,7
1,2,4,7
1,2,4,7
0-65535
GPRS
PRACH Blocks
GPRS
PAGCH Blocks
GPRS
0-12
PBCCH Blocks
GPRS
1-4
1
1
0.48sec,0.96sec,1.92sec,3.84sec,7.68sec,15.36sec,30.72sec,61.44s
0-12
0.96sec
0.96sec
15.36sec
15.36sec
0.24sec
0.24sec
-2db
-2db
10sec
10sec
10dB
10dB
60sec
60sec
type1
0.48sec,0.96sec,1.92sec,3.84sec,7.68sec,15.36sec,30.72sec,61.44s
nodrx,0.24sec,0.48sec,0.72sec,0.96sec,1.20sec,1.44sec,1.92sec
Non-DRX Period
GPRS
GPRS
GPRS
GPRS
Extension MR Period
GPRS
Extension MR Type
GPRS
type1,type2,type3type1
Interference Frequency
GPRS
0-31
NCC Permitted
GPRS
GPRS
0-255
em0,em1
11111111
em0
em0
GPRS
Yes or No
Yes
Yes
GPRS
Yes or No
Yes
Yes
GPRS
GPRS
0-7
Area specific
Area specific
No packet access,Packet access of level 1,Packet access of levels 1-2
GPRS
GPRS
Pan Max.
GPRS
Pan Increment
GPRS
Pan Decrement
GPRS
BS_CV_MAX
GPRS
GPRS
-52db,-48db,-44db,-40db,-36db,-32db,-28db,-24db,-20db,-16db,-12d
10sec,20sec,30sec,40sec,50sec,60sec,70sec,80sec,90sec,100sec,11
0dB,10dB,20dB,30dB,40dB,50dB,60dB,infinity,nouse
60sec,120sec,240sec,480sec,960sec,1920sec,3840sec,7680sec
Yes or No
nc0,nc1,nc2
No
No
nc0
nc0
12
12
4,8,12,16,20,24,28,32,nouse
0,1,2,3,4,5,6,7,nouse
0,1,2,3,4,5,6,7,nouse
0-15
10
10
Four access pulses by default,RLC/MAC control block by default
GPRS
GPRS
T3192
GPRS
T3168
GPRS
NMO
GPRS
ALPHA
GPRS
GAMMA
GPRS
TAVGW
GPRS
GPRS
NAVGI
GPRS
[0 (500 ms)
8bit
or 11bit
8bit
8bit
1 (1000
ms)
[0 (500 ms)
2
(1500 ms)
0-64
4
4
1 (1000 ms)
3 (2000 ms)
2 (1500 ms)
500ms
500ms
4 (2500 ms)
3 (2000 ms)
500ms
500ms
5 (3000 ms)
4 (2500 ms)
Network
Operation Mode I,Network Operation Mode II,Network Opera
6
(3500
ms)
0.0,0.1,0.2,0.3,0.
Network OperatiNetwork Opera
5 (3000 ms)
7
(4000 ms)
4,0.5,0.6,0.7,0.8,
6 (3500 ms)
1
1
0.9,1.0
7
(4000 ms)
0-31
0-25
0-25
bcch,pdch
0-15
14
14
10
10
10
10
pdch
pdch
BSC Cureent
Setting(390
0 BTS
Version
cell specific
cell specific
No
Yes
63
Yes
A5/0A5/2
Yes
Yes
Yes
No
0
Yes
Shall Use
0
0
No
0
No
Yes
6dB
50
2 Multiframe P
1
11111111
No
50
Yes
0
15
63
31
23
15
63
31
23
010101
25
17
12
28
19
15
10010101
1
Different Band
No
No
No
No
No
Yes
0
15
+0dB
No
Yes
15
0
2
RSCP
8
Use Qsearch_I
15
3
1
Yes
0
Yes
20
No
00000
0000000000
4 Times
2
4
No
34
29
23
5
5
5
No
60
60
200
150
50
50
60
-110
180
Allowed & Rec
101111
20
24
20
24
70
No
4
16
20
4
45
No
4
5
50
25
Preference for
68
63
10
1
4
4
3
4
35
50
50
90
4
5
5
25
30
5
10
No
1
5
5
No
2
10
10
90
80
No
Yes
50
No
4
5
35
50
25
Preference for
35
25
60
50
5
5
90/cell specific
cell specific
cell specific
3
10
40
15
5
5
Yes
cell specific
cell specific
Underlaid Subc
System Optimi
61
No
61
cell specific
System Optimi
2
3
0
61 / cell specif
60
5
cell specific
10
No
No
Yes
Yes
Yes
80
4
0
25
0
0
4
20
3
15
2
3
5
10
25
70
90
10
60
60
60
60
5
40
41
42
43
44
45
46
47
48
49
50
60
8
55
No
0
10
10
10
10
10
10
10
10
60
60
61
Open
255
10
4
6
2
10
6
2
6
2
6
2
10
63
cell specific
cell specific
63
4
4
3
2
4
4
3
16
Once every se
Yes
No
No
No
Yes
No
4
4
2
2
Close
3
4
NO
10
20
4
5
Yes
8
0
2
30
No
2
3
3
4
2
3
2
3
cell specific
10
Yes
Yes
Yes
Yes
Yes
No
Yes
No
No
No
No
No
Yes
0
0
0
0
0
0
0
0
8
6
13
13
12
12
14
14
14
14
18
18
4
3
1
1
3
3
8
6
13
13
12
12
14
14
14
14
18
18
4
3
1
1
3
3
2
1
2
3
5
16
8
2
6
3
8
8
4
0
0
2
3
0
25
33
3
0
18
25
0
0
Yes
5
5
5
5
3
16
10
2
5
3
8
8
2
0
0
2
0
0
Yes
5
5
5
5
HWIII Power Co
2
0
25
45
3
0
18
25
3
5
4
6
95
Yes
cell specific
cell specific
Close
Close
80
80
60
cell specific
Yes
2
30
4
2
7
4
30
45
30
35
Yes
Yes
Yes
Yes
Yes
No
Not Support
Quality Preferr
Yes
60
cell specific
cell specific
26000
34000
10000
10
15000
1000
30000
25000
30000
5000
10000
10000
5000
3000
220
180
5
2
Forced turn-on
Interference B
Yes
No
No
Yes
Yes
Maximum/Mean
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
No
15
Yes
Yes
5
Yes
360
360
5000
15
100
15
10
36671
NO
2
2
2
2
3
65535
5
20
48
90
98
104
108
115
90
Yes
0001110110
StartUp
Not Report
Invalid
10
3
20
Not Support
No handover be
16
6
Not Support
Not Support
Not Support
MCS6
UNFIXED
MCS2
UNFIXED
8
LA
20
10
20
10
5
5
CS2
UNFIXED
20
10
20
10
5
5
CS1
UNFIXED
30
2
No preempt of
30
Only convert a
80
70
cell specific
cell specific
cell specific
Report the freq
-110dB
2
2
2
NoExclusive
Permit
2dB
10sec
Yes
0
c31standard
2dB
No
No
6
16
14
13
12
20
20
7
7
7
7
0
1
4
1
0.96sec
15.36sec
0.24sec
-2db
10sec
10dB
60sec
type1
1
1
em0
Yes
Yes
Area specific
Packet access o
No
nc0
12
4
2
10
Four access pul
8bit
4
500ms
500ms
Network Operat
0.6
14
10
10
pdch
2
Parameter Description
ThisAttach?detach
parameter indicates
the half rate used
when
call is initially
established.As
(H) includes
IMSI
allowed:Detach,This
is the
Lastamessage
that MS
Sends when AMR.ACS
it is Powered-Off,If
set
four
at most,
this to
parameter
can only
given fourMS
values:
1, 2, and 3. These
four
to coding
No thenrates
System
will have
wait for T3212
forbe
considering
to be0,
"OFF-Line".IMSI
Attach
is values
First
correspond
to low-to-high
rates
in AMRits
ACS
(H).
message
generated
by MS tohalf
Inform
Network
Presence
This parameter must meet the following conditions:AMR DL Coding Rate adj.th2 (H) < AMR DL Coding
The DL
AMR
Starting
Mode
(H) (H)
should
be within
the AMR
(H). (H) ] < [AMR DL
Rate adj.th3 (H) [AMR
Coding
Rate
adj.th2
+ AMR
DL Coding
RateACS
adj.hyst2
Coding Rate adj.th3 (H) + AMR DL Coding Rate adj.hyst3 (H)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th2 (H) < AMR DL Coding
Rate adj.th3 (H) [AMR DL Coding Rate adj.th2 (H) + AMR DL Coding Rate adj.hyst2 (H) ] < [AMR DL
Coding Rate adj.th3 (H) + AMR DL Coding Rate adj.hyst3 (H)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th1 (H) < AMR DL Coding
Rate adj.th2 (H) [AMR DL Coding Rate adj.th1 (H) + AMR DL Coding Rate adj.hyst1 (H) ] < [AMR DL
Coding Rate adj.th2 (H) + AMR DL Coding Rate adj.hyst2 (H)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th2 (H) < AMR DL Coding
Rate adj.th3 (H) [AMR DL Coding Rate adj.th2 (H) + AMR DL Coding Rate adj.hyst2 (H) ] < [AMR DL
Coding Rate adj.th3 (H) + AMR DL Coding Rate adj.hyst3 (H)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th2 (H) < AMR DL Coding
Rate adj.th3 (H) [AMR DL Coding Rate adj.th2 (H) + AMR DL Coding Rate adj.hyst2 (H) ] < [AMR DL
Coding Rate adj.th3 (H) + AMR DL Coding Rate adj.hyst3 (H)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th1 (H) < AMR DL Coding
Rate adj.th2 (H) [AMR DL Coding Rate adj.th1 (H) + AMR DL Coding Rate adj.hyst1 (H) ] < [AMR DL
Coding Rate adj.th2 (H) + AMR DL Coding Rate adj.hyst2 (H)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th2 (H) < AMR UL Coding
Rate adj.th3 (H) [AMR UL Coding Rate adj.th2 (H) + AMR UL Coding Rate adj.hyst2 (H) ] < [AMR UL
Coding Rate adj.th3 (H) + AMR UL Coding Rate adj.hyst3 (H)]
This parameter must meet the following conditions:AMR uL Coding Rate adj.th2 (H) < AMR uL Coding
Rate adj.th3 (H) [AMR UL Coding Rate adj.th2 (H) + AMR UL Coding Rate adj.hyst2 (H) ] < [AMR UL
Coding Rate adj.th3 (H) + AMR UL Coding Rate adj.hyst3 (H)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th1 (H) < AMR uL Coding
Rate adj.th2 (H) [AMR UL Coding Rate adj.th1 (H) + AMR UL Coding Rate adj.hyst1 (H) ] < [AMR UL
Coding Rate adj.th2 (H) + AMR UL Coding Rate adj.hyst2 (H)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th2 (H) < AMR UL Coding
Rate adj.th3 (H) [AMR UL Coding Rate adj.th2 (H) + AMR UL Coding Rate adj.hyst2 (H) ] < [AMR UL
Coding Rate adj.th3 (H) + AMR UL Coding Rate adj.hyst3 (H)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th2 (H) < AMR UL Coding
Rate adj.th3 (H) [AMR UL Coding Rate adj.th2 (H) + AMR UL Coding Rate adj.hyst2 (H) ] < [AMR UL
Coding Rate adj.th3 (H) + AMR UL Coding Rate adj.hyst3 (H)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th1 (H) < AMR UL Coding
Rate adj.th2 (H) [AMR UL Coding Rate adj.th1 (H) + AMR UL Coding Rate adj.hyst1 (H) ] < [AMR UL
Coding Rate adj.th2 (H) + AMR UL Coding Rate adj.hyst2 (H)]
7.40Kbps,6.70Kbps5.90Kbps5.15Kbps4.75Kbps,Default is 01101,If only 1 value is selected Starting
Mode will be 0,Therwise 1,2 0r 3
4.75 Kbps-12.2 Kbps 12.2 Kbps, 10.2 Kbps, 7.95 Kbps, 7.40 Kbps, 6.70 Kbps, 5.90 Kbps, 5.15 Kbps, 4.75
Kbps,If only value is selscted then AMR starting Mode(F) must be 0,If two are selected then AMR Starting
Mode(F) must be 1.
This parameter must meet the following conditions:[ AMR DL Coding Rate adj.th2 (F) + AMR DL Coding
Rate adj.hyst2 (F) ] < [AMR DL Coding Rate adj.th3 (F)+ AMR DL Coding Rate adj.hyst3(F)]
This parameter must meet the following conditions:[ AMR DL Coding Rate adj.th2 (F) + AMR DL Coding
Rate adj.hyst2 (F) ] < [AMR DL Coding Rate adj.th3 (F)+ AMR DL Coding Rate adj.hyst3(F)]
This parameter must meet the following conditions:[ AMR DL Coding Rate adj.th1 (F) + AMR DL Coding
Rate adj.hyst1 (F) ] < [AMR DL Coding Rate adj.th2 (F)+ AMR DL Coding Rate adj.hyst2(F)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th2(F) < AMR DL Coding
Rate adj.th3(F) [ AMR DL Coding Rate adj.th2(F) + AMR DL Coding Rate adj.hyst2 (F) ] < [AMR DL Coding
Rate adj.th3(F) + AMR DL Coding Rate adj.hyst3 (F)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th2(F) < AMR DL Coding
Rate adj.th3(F) [ AMR DL Coding Rate adj.th2(F) + AMR DL Coding Rate adj.hyst2 (F) ] < [AMR DL Coding
Rate adj.th3(F) + AMR DL Coding Rate adj.hyst3 (F)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th1(F) < AMR DL Coding
Rate adj.th2(F) [ AMR DL Coding Rate adj.th1(F) + AMR DL Coding Rate adj.hyst1 (F) ] < [AMR DL Coding
Rate adj.th2(F) + AMR DL Coding Rate adj.hyst2 (F)]
This parameter must meet the following conditions:[ AMR UL Coding Rate adj.th2 (F) + AMR UL Coding
Rate adj.hyst2 (F) ] < [AMR UL Coding Rate adj.th3 (F)+ AMR UL Coding Rate adj.hyst3(F)]
This parameter must meet the following conditions:[ AMR UL Coding Rate adj.th2 (F) + AMR UL Coding
Rate adj.hyst2 (F) ] < [AMR UL Coding Rate adj.th3 (F)+ AMR UL Coding Rate adj.hyst3(F)]
This parameter must meet the following conditions:[ AMR UL Coding Rate adj.th1 (F) + AMR UL Coding
Rate adj.hyst1 (F) ] < [AMR UL Coding Rate adj.th2 (F)+ AMR UL Coding Rate adj.hyst2(F)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th2(F) < AMR UL Coding
Rate adj.th3(F) [ AMR UL Coding Rate adj.th2(F) + AMR UL Coding Rate adj.hyst2 (F) ] < [AMR UL Coding
Rate adj.th3(F) + AMR UL Coding Rate adj.hyst3 (F)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th2(F) < AMR UL Coding
Rate adj.th3(F) [ AMR UL Coding Rate adj.th2(F) + AMR UL Coding Rate adj.hyst2 (F) ] < [AMR UL Coding
Rate adj.th3(F) + AMR UL Coding Rate adj.hyst3 (F)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th1(F) < AMR UL Coding
Rate adj.th2(F) [ AMR UL Coding Rate adj.th1(F) + AMR UL Coding Rate adj.hyst1 (F) ] < [AMR UL Coding
Rate adj.th2(F) + AMR UL Coding Rate adj.hyst2 (F)]
12.2 Kbps, 10.2 Kbps, 7.95 Kbps, 7.40 Kbps, 6.70 Kbps, 5.90 Kbps, 5.15 Kbps, 4.75 Kbps,Default is
11100100,
In normal
Assignment
proceedure,after
receiving
"Assignment
Failure"
message from
MS,BSc
does not
Indicates
Max No. of
Assignment Retry
times.Valid
only when
TCH Assignment
Retry
is Enabled.
Inform this to MSC immediately.Instead it Re-Assigns Radio Channel & Re-Origenates assignment
Proceedure.Option
Different
Band
cause Assignment
failure
to occur
when
Assignment
Failure
Whether
to disable
users
acan
particular
cell to the
receive
messages
in again
DL,but
MS in
call
can receive
parameter
isall
used
to in
concurrently
deliver
channel
activation
message
and
immediate
Occurs
due to
Interference
or
Faulty
TRX
ThisThis
parameter
indicates
whether
to enable
the
function
that
the
TCHH
is
adjusted
according
to
Abis
messages
in DLof signaling. Thus the response speed of
assignment command message to quicken the
processing
the
resources.
Whether to disable all users
in a particular
cell to send messages in DL.
network
is ensured.
The BSC preferably assigns TCHH to the MS according to the Abis resource load when the Abis resources
This function is used in satellite transmission
mode. In satellite transmission mode, the Immediate
are insufficient.
Assignment
Opt
parameter
must
be
set
to
Yes
to
minimize
effect of the
transmission
on time
This parameter indicates whether the enhanced multi
levelthe
precedence
andsatellite
preemption
(eMLPP) function
delay.
terrestrial
transmission
mode,isthe
default
value
of the
thisMS
parameter
is No.
After
this parameter
is set
to Yes,
thethe
BSC
preferably
assigns
to
if the such
Abis
resource
load
is allowed.
The In
eMLPP
means
that
network
allowed
toTCHH
use different
policies
as queuing,
exceeds
the Flex
Abis
Prior Abis
Threshold
or Fix Abis
Prior Abis
Load
preemption,
and direct
retry
according
to Load
the calls
with different
priorities
when
the Threshold
network resources
are seized.
This parameter indicates whether the reassignment function is allowed.
This parameter indicates the reporting threshold for TDD cells.When the receive level of the TDD cell in
the measurement report is greater than the value of this parameter, the measurement report is
valid.After the valid measurement report is filtered, the TDD cell joins in the cell priority rank
This parameter indicates the reporting offset for TDD cells.When ranking the priority of a TDD cell, it is
recommendedThis
to first
add theindicates
value of this
parameter
to the receive
level of
in the measurement
parameter
whether
the reassignment
function
is it
allowed.
report.
If this parameter is set to Yes, the BSC originates a second assignment when the BSC receives the
Assignment Failure message. If this parameter is set to Yes, it is good to raise the call completion rate of
the MS. If there are a lot of MS assignment failures, however, the BSC originates re-assignments for a lot
of MSs. As a result, the BSC will experience more load.
The TDD cell can become a candidate cell only when the average receive level of the TDD cell is greater
than the "FDD Q Offset" of the serving cell.
This parameter indicates the reporting offset for 3G cells.When ranking the priority of a 3G cell, it is
recommended to first add the value of this parameter to the receive level of it in the measurement
report.
This parameter indicates the report offset for 3G cells.
When ranking the priority of a 3G cell, it is recommended to first add the value of this parameter to the
receive level of it in the measurement report
This parameter indicates the reporting offset for DCS1800 cells.When ranking the priority of a
GSM1800cell based on its frequency band, it is recommended to first add the value of this parameter to
the receive level of it in the measurement report
This parameter indicates the reporting offset for DCS1800 cells.When ranking the priority of a
GSM1800cell based on its frequency band, it is recommended to first add the value of this parameter to
the receive level of it in the measurement report
This parameter indicates the reporting threshold for GSM900 cells.When ranking the priority of a
GSM900 cell based on its frequency band, it is recommended to first add the value of this parameter to
thereporting
receive level
offor
it in
the measurement
This parameter indicates the
offset
GSM900
cells.When report
ranking the priority of a GSM900
cell parameter
based on its
frequency
it is recommended
first add the
value of this
parameter
to the
This
indicates
theband,
threshold
of level for cellto
reselection
in connection
mode.In
connection
receive
level
in the
measurement
report.the MS starts to search for 3G
mode, if the signal level in the
service
cell of
is it
below
(0-7)
or above (8-15),
cells.
For example:If this parameter is set to 5 and the signal level in the service cell is below 5, the MS starts
to search for 3G cells.
If this parameter is set to 10 and the signal level in the service cell is above 10, the MS starts to search
This parameter indicates the strength added to
signal strength before the MS delivers the
forthe
3Greceived
cells
enhanced measurement report
This parameter indicates whether a cell with invalid BISC is allowed in the measurement report
ThisThis
parameter
indicates
onewhether
of the threshold
level for
reselection
packet
packet
parameter
indicates
the MS isofallowed
tocell
search
for a 3Gincell
whenmode.In
the BISC
must mode,
be
parameter
one of
the
of or
level
for the
reselection
of 3G to
cells.
Onlyfor
when
the
if This
the signal
level indicates
in the service
cell
is threshold
below (0-7)
above
(8-15),
the MS starts
search
3G cells.
decoded
receive level of a 3G cell is greater than FDD Qmin, the 3G cell can be one of the candidate cells for
reselection.0=
-20dB
For example:If this parameter is set to 5 and
the signal level
in the service cell is below 5, the MS starts
1= for
-6dB
to search
3G cells.
2=in-18dB
If this parameter is set to 10 and the signal level
the service cell is above 10, the MS starts to search
3=
-8dB
for
3G
cells
4= -16dB
5= -10dB
This parameter indicates the number of UTRAN6=
FDD
cells that a best cell list or a measurement report
-14dB
should
include
7= -12dB.
Default value= -20dB
This parameter indicates the strength added to the received signal strength before the MS delivers the
enhanced measurement report
Only when the average receive level of a 3G cells is FDD Q Offset greater than that of the current service
cell, the 3G cell can become a candidate cell
Thisparameter
parameterindicates
indicatesthe
thethreshold
thresholdofoflevel
levelfor
forcell
cellreselection
reselectionininidle
connection
mode
befour
the signal
BTS
This
mode.In idle
mode,
if the
receives
the Qsearch
C. MS starts
This parameter
is service
used forcell
theisMS
to report
neighboring
cell explanation
ofto
multiple
bands.
It is sent in
level
in
the
below
(0-7)
or
above
(8-15),
the
search
for
3G
cells.
If the system information indicates "MBR", the MS reports the quantities of neighbor cells on different
the example:If
system messages
2ter andis5ter.0:
MS
reports
the
measurement
resultsisofbelow
six neighboring
cells
For
this parameter
set to The
5the
and
the
signal
level
in the
service
5, theband
MS starts
frequency bands.When
the MS reports
quantity
of neighbor
cells
on thecell
same frequency
with
known and permitted by the NCC at the bands
with
the
best
signal
regardless
of
the
band
at
which
the
to search
for"Serving
3G cells.
the serving cell, a maximum of the
value of
Band Reporting" can be reported.
neighboring
cell
isservice
located.
If this parameter is set
to
10
and
the
signal
level
in
the
cell
is
above
10,
the
MS
starts
to
search
These neighbor cells must meet the following requirements:
1: The MS reports the measurement result of a for
neighboring
cell known and permitted by the NCC at each
(1) The receive levels of the neighbor cells must3G
becells
higher than "900 Reporting Threshold" or "1800
band with the best signal (the band serving the current cell not included). The MS reports the
Reporting Threshold".
measurement result of the neighboring cell at the band serving the current cell in the redundant
(2)
The
BSIC
of
thereceive
neighbor
mustpower
be valid.
If aposition.
class 3 MS
on redundant
the DCS1800
band is
does
thecells
original
command after
random
access,
If the
position
still not
available,
the
MS
reports
the measurement
results
of other
(3)
The
signals
of
the
neighbor
cells
must
be
the
strongest
among
thethe
neighbor
on the same
the
power thatcells
the regardless
MS uses is of
the
MSbands
maximum
transmit
power levelall
plus
power cells
calculated
the
neighboring
the
at which
the neighboring
cells
are located.2:
The MS from
reports
frequency
band. GSM 05.08
power
deviation.
See
protocol
the measurement results of two
neighboring
cells
known
and permitted by the NCC at each band with
The
MS signal
does not
the original
power command
after random
access.
This
indicates
the
best
(thereceive
band serving
the current
cell not included).
The MS
reports
theparameter
measurement
result
whether
the
power
deviation
is
added
to
the
class
3
MS
on
the
DCS1800
band
on
the
basis
of the
of the neighboring cell at the band serving the current cell in the redundant position. If the redundant
maximum
MS transmit
power
position is still available, the MS reports
the measurement
results
of other neighboring cells regardless of
the bands at which the neighboring cells are located.
3: The MS reports the measurement results of three neighboring cells known and permitted by the NCC
at each
band
with thesupport
best signal
(the
bandthat
serving
current
cell not included).
MS reports
Use for
Dual-Band
MS to
inform
Dualthe
Band
is Supported.
Invalid forThe
Single-Band
MSthe
measurement result of the neighboring cell at the band serving the current cell in the redundant
determins
the
time of Disconnecting
call when the
MS MS
failsreports
to Decode
SAACH sent byresults
BTS,Once
a
position.
If the
redundant
position is stilla available,
the measurement
of other
dedicated
channel iscells
assigned
a Timer
is bands
started.
BTS sussceesfully
Decdes
a SACCH,it
neighboring
regardless
of S
the
atEvery
whichtime
the neighboring
cells are
located.
Increments
by 2 otherwise
Decrement
When this
timer
reaches
0 Radio
will be Fail
For MSs
whose access
class is from
0 to 9, if by
the1.Emergent
Call
Disable
is set
to No,Link
emergency
calls are
When the traffic
volumes
of multiple
the
same
and there
is no
requirement
on the
allowed.For
MSs whose
access
class isbands
from are
11 to
15,
emergency
calls
arespecial
not allowed
only when
the
band, the MBR (Multi
Report)
set
When
the traffic Call
volumes
of multiple
are different
accessBand
control
bit is is
set
toto
0 0.
and
the Emergent
Disable
is set to bands
Yes
and
the
MS is expected
enter
band preferentially,
MBR (Multi
BandofReport)
set to class
3. In other
This
parameter
is usedtofor
loadacontrol.
It determinesthe
whether
the users
specialisaccess
are
cases except the first two cases, theallowed
MBR (Multi
Band the
Report)
is set to 1 or 2. For details, see protocol
to access
network.
This parameter is used to control the load. It determines whether the users of common access class are
allowed to access the network
This parameter indicates the maximum times for sending Channel Request messages by the MS during
an immediate assignment.
This parameter indicates the maximum number of retransmissions of the immediate assignment
message. When this number is reached, no retransmission is performed
Within the period specified by this parameter, the immediate assignment message can be dispatched
and retransmitted. Otherwise, the message cannot be dispatched or retransmitted
Whwther to use Imm Assignment Retry or not
When establishing LAPDm between the BTS and MS, the BTS sends frame I to the MS. When the MS
detects error in the frame I, the BTS should resend frame I.This parameter indicates the Max retransmit
times
of frame
on the
(aBTS
full-rate
channel).
When establishing LAPDm
between
the IBTS
andFACCH
MS, the
sends
frame I to the MS. When the MS
detects error in the frame I, the BTS should resend frame I.This parameter indicates the Max retransmit
times
of frame
on the
(aBTS
full-rate
channel).
When establishing LAPDm
between
the IBTS
andFACCH
MS, the
sends
frame I to the MS. When the MS
detects error in the frame I, the BTS should resend frame I.This parameter indicates the Max retransmit
times
of frame
I onthe
theBTS
SDCCH.
When establishing LAPDm between
the BTS
and MS,
sends frame I to the MS. When the MS
detects error in the frame I, the BTS should resend frame I.This parameter indicates the Max retransmit
of frame
I onthe
theBTS
SACCH
When establishing LAPDm betweentimes
the BTS
and MS,
sends frame I to the MS. When the MS
detects error in the frame I, the BTS should resend frame I.This parameter indicates the maximum
times
frame
I during
the multi-frame
When establishingretransmission
LAPDm between
the of
BTS
and MS,
the BTS
sends framerelease.
I to the MS. When the MS
detects error in the frame I, the BTS should resend frame I.This parameter indicates the maximum
retransmission times of frame I.
This parameter controls whether the BSC delivers the LAPDm N200 parameter to the BTS.
This parameter determines the expiry value of T200 when the SDCCH supports SAPI3 services.
This parameter determines the expiry value of T200 on the SACCH on the SDCCH
This parameter determines the expiry value of T200 on the SACCH over the Um interface when the TCH
supports SAPI3 services
This parameter determines the expiry value of T200 on the SACCH over the Um interface when the TCH
supports SAPI0 services
This parameter determines the expiry value of T200 on the FACCH or full-rate channel over the Um
interface
This parameter determines the expiry value of T200 on the FACCH or full-rate channel over the Um
This parameter
indicates
which
speech
version
is on
supported.
It consists
sixinterface,T200
bits.
This parameter
determines
the expiry
value
ofinterface
timer
T200
the SDCCH
over theofUm
Prevents Dead-Lock on Data Link Layer of Um Interface.two Entities use Acknowlege & Retransmission
The
six bits,
from the any
most
significant
one to
the
least significant
bit indicates whether the
BSC
method.
Whenever
one
entity sends
any
message
it should one,
haveeach
acknowlegment,Otherwise
T200
supports thewill
following
speech versions:
be
Expired.
This is min Level
of
RACH
upon
which
it
will
be
accepted
bythe
network.If
level
is
less
than
this
thrsh
TRX Aiding Not Allowed indicates that the TRX aiding function is not allowed.
then RACH will be disgarded.
Half-rate version 3
Allowed
and
Recover
Forbidden
indicates
thatsignal
the TRX
aiding
function
is allowed
is the
the system can determine whether the received
is the
random
access
signal ofbut
theswitchback
MS through
forbidden
after
the
faulty
TRX
is
recovered.
correlation of training
sequence
TSC
(41
bits)
and
can
calculate
the
TA
value.
Half-rate version 2
Allowed and Recover Immediately indicates
that the
TRX 1aiding function is allowed and immediate
Half-rate
version
switchback is allowed after the faulty TRX is recovered.
Full-rate version 3
Allowed and Recover When Check Res indicates that the TRX aiding function is allowed but immediate
switchback is forbidden after the faulty TRX
is recovered.2,
The switchback is not performed until the
Full-rate
Indicates
RLT ofversion
AMR
Rate
resources
are checked
in theHalf
early
morning.
Full-rate version 1.
Indicates RLT of AMR FULL Rate
If the value of one bit is 1, it indicates that the BSC supports the corresponding speech version. If the
value of one bit is 0, however,
it indicates
the BSC of
does
notHalf
support
Indicates
SACCHthat
MultiFrame
AMR
Rate the corresponding speech
version.
Indicates SACCH MultiFrame of AMR FULL Rate
For example, if the parameter is set to 001011, infer that full-rate version 1, full-rate version 2, and halfversion
1 arethe
supported.
When target cells are selected during rate
direct
retry, only
cells whose loads are smaller than or equal to
the Directed Retry Load Access Threshold are selected as candidate target cells
In the BTS2X version (BTS24 not included), this parameter indicates the level threshold for the system to
determine MS random access. When the receive level of the random access burst timeslot is greater
than this threshold and the access demodulation is successful, the BTS considers that the timeslot is
busy and determines whether the RACH access is valid based on the parameter Random Access Error
Threshold. In the BTS2X version, the parameter RACH Busy Threshold determines whether the timeslot is
busy and
affects the normal
access
ofEnabled
the MS. is
The
allowed
the level
the MS
When
the Assignment
Cell Load
Judge
setMS
to access
Yes, theisdirect
try only
flow when
is allowed
if theoffollowing
random access burst
is greater
than
the
RACH Busy Threshold.
two
conditions
are
met:
In the BTS24 version, this parameter
of the MS random access for the
The cell indicates
supports the
the level
directthreshold
try function.
system toThe
determine
thetoreceive
level
of the
access
burst timeslot is
load of the
the RACH
cell is busy
largerstate.
than When
or equal
the Cell
Direct
Try random
Forbidden
Threshold.
greater than the threshold, the BTS
thatsend
the timeslot
is MS
busy. This parameter also indicates
Maxconsiders
Times a Cell
Paging to
whether the MS access is allowed. The MS access is allowed only when access level (including random
access and handover access) is greater than the threshold.
When BTS sends physical information to the MS, the BTS starts the timer T3105.If the timer T3105 times
Informs
the 0Network
about
UPLINK
Connection
Status.Every
BTSinformation
successfullytodecodes
0-63
with
indicating
-110
dBm
and
63 indicating
-47 dBmtime
In the
out before
receive
the
SAMB
frame
from
MS, BTS
re-sends
physical
MS and Measurement
restarts
the
Report
sent
by
MS,Counter
for
determining
Radio
Link
Path
is
Incremented.But
if
fails
decrements
BTS2X
version
nottimes
included),
this parameter
the
level
threshold
forthen
the
system
tothe
During
asynchronous
handover,
thefor
MSre-sending
constantly
sendsindicates
handover
access
bursts to
the
BTS.
Usually,
timer
T3105.
The (BTS24
maximum
physical
information
is Ny1.The
physical
information
is
by
1 MS
untill
0 then
BTS Upon
ends
Radio
&frames
sends
Connection
Failure
BSC
determine
random
access.When
theConnection
receive
level
of
a random
access
burst
timeslot
ofto
the
RACH
Timer
T3124
lasts
320which
ms.
detecting
theTDMA
bursts,
the
BTS
physical
information
to
the MS
sent through
FACCH,
is sent
every
four
andreturns
takes
18
ms. IfIndication
the value
of
T3105
isis
greaterthe
than
this
threshold,
the
BTS
considers
that
the timeslot
is busy.
This parameter
must
be set
through
main
DCCH/FACCH
and
sends
the MSG_ABIS_HO_DETECT
message
to the
BSC.
Meanwhile,
smaller
than
or
equal
to 18 ms,
then
BTS
should
re-send
the physical
information
to the
MS
when
the
based
theT3105
actual
sensitivity
of
thetime.This
BTS
andtimeout
the lowest
access
level ifofthe
the
MS
to ensure
the uplink
the on
timer
information
containing
information
on
different
physical
layers
timer
T3105
times starts.The
out
for thephysical
first
is meaningless
physical
information
sent and
at
downlink
balance.
Thisaccess.
parameter
also
affects
handover
access
of RACH
BURST
during
asynchronous
guarantees
correct
theFACCH
timer
T3105
expires
before
the
BTS
receives
theperiod.Considering
SAMB
frame from
the
previous
time is MS
not
sent
onIfthe
because
the time
is shorter
than
a FACCH
handover.
Forfactors,
the BTS3X
series
and
double-transceiver
BTSs,
thisthis
parameter
affect the
MS access
thems
MS,
BTS
re-sendsminimum
the physical
information
to thedoes
MS.
the
previous
20
is the
the
reasonable
value
for
parameter.
Atnot
present,
default
but affects the report of CCCH_LOAD_IND.
If the
level received
by the BCCH at the network side is
value of this
parameter
is 70 ms.
During
thethan
decision
of 3GBusy
better
cell
handover
algorithm,
3G
better
cell
is is
originated
only SAMB
when
This
parameter
indicates
whether
the
better 3G
cell
algorithm
allowed
the
RACH
Threshold,
the
ishandover
counted
once
the
decoding
is
If greater
the number
of
resending
times
exceeds
thisCCCH_LOAD_IND
parameter
(Ny1)
and
the handover
BTS
haswhether
receive
no correct
theframe,
period
that
meets
the
conditions
of
the
3G
better
cell
handover
algorithm
in
the
measurement
period
successful.
Thesends
RACHthe
whose
is lower than
the
RACH Busy
Threshold
and whose
decoding
is
the BTS
BSC level
a connection
failure
message,
which
also indicates
handover
failure.
is measurement
greater than 3G
Better
Cell RACH
HO Valid
Time.
successful is also counted. The
period
is the
mean
load timeslot. If the value of this
parameter is too small, the BTS easily considers that the RACH timeslot is busy and reports overload
This
valid time
of the
3G better
cell handover
messages to
theparameter
BSC. If theindicates
value is the
too high,
the BTS
cannot
determine
the statealgorithm.
of the RACH timeslot
If the Outgoing-RAT
HO Allowed parameter
is set to Yes and
the3G
Better
3Gcell
Cell
HO Allowed
parameter is
This
better
handover
algorithm
correctly.
In parameter
the BTS24 indicates
version, ifthe
thismeasurement
parameter is time
usedof
tothe
judge
busy
timeslot,
its setting
is consistent
set to Yes,better 3G cell handover is triggered when the RSCP of a 3G neighboring cell is greater than
that in the BTS30. If this parameter is the level threshold for valid random access, its setting is
RSCP Threshold for Better 3G CELL HO in a period.
consistent with that in the BTS20. The setting of this parameter for the BTS312, BTS3001C, BTS3001C+,
and
the double-transceiver
BTSs
is the
same as that in the BTS30.
When the BTS3002C
Inter-RAT0-63
HO
Preference
is set to
2 (2G
cells
with 0 indicating
-110
dBm
andare
63preferentially
indicating -47selected
dBm. according to the
threshold), 3G cells are the preferential selection for handover if the receive level of the first candidate
2G cell is smaller than or equal to HO Preference Threshold for 2G Cell.
This parameter indicates whether a 2G cell or a 3G cell is preferentially selected during cell handover
A quick switchover can be initiated only when the path loss difference between chain-type adjacent cells
and serving cells is not smaller than the value of this parameter within a measurement period.
This parameter indicates the level value to punish the original cell afthe a quick handover is triggerd
This parameter indicates the length of time to punish the orignal cell after a quick handover is performed
When the received number of measurement reports is no larger than the "Neglected Number of
Measurement Reports", the measurement reports are not filtered and the quick handover is not decided
either.
The triggering of quick switchover must conform to
the P/N rule. That is, within P seconds, there must be
This
parameter
preventswhen
you from
making anconditions
incorrect switchover
decision
on the
of in
anconjunction
inaccurate
N
seconds
in succession
the triggering
are met: This
parameter
is basis
applied
measurement
report.
with the following parameters:Quick Handover
Up Trigger
Level (dB) or Quick Handover Down Trigger
Level (dB)
This parameter indicates the number of measurement
reports filtered after the BSC receives
measurement reports from serving cells
Quick Handover Static Time
The quick switchover can be initiated only when the MS speed is greater than Quick Move Speed Thres
within a measurement period.This parameter
isSpeed
applied
in conjunction
with the following parameters:
Quick Move
(m/s) when
This quick
parameter
indicates
P mentioned
IfThres
the duration
the triggering
conditions
are
The
switchover
can the
be initiated
only previously.
when the downlink
level of a serving
cell is lower
than Quick
met is not
smaller
than
the
value
of
this
parameter
within
the
time
preset
by
Quick
Handover
Static
Handover
Down
Trigger
Level
within
a
measurement
period
after
the
measurement
reports
of
the
cell
are
Quick Handover Up Trigger Quick
Level Handover
(dB) or Quick
Handover
Down Trigger Level (dB)
Offset
(dB)
Time,isquick
switchover
is triggered.
compensated.This
parameter
applied
in
conjunction
with
the
following
parameters:
The quick switchover can be initiated only when the uplink level of a serving cell is lower than Quick
Quick Handover
Static
Time
Handover Up Trigger Level within a measurement
period
after
the measurement reports of the cell are
Quick
Move
Threswith
(m/s)
filtered.This parameter is
applied
in Speed
conjunction
the following parameters:
Quick Handover Last Time
Quick
Handover
Static
Time
Quick
Handover
Static
Time(0.5s)
Quick Handover Offset (dB)
Quick
Handover
Quick
Move
Speed Last
ThresTime
(m/s)
If the ratio of channel occupancy in overlaid subcell is greater than the value of this parameter, it is not
Offset
(dB)
allowed to make the load handoverQuick
from Handover
underlaid cell
overlaid cell in an enhanced dual-band
Quick
Handover
Lastto
Time
network.
P/N criterion: In P measurement reports,
N measurement
results
meet handover requirements. Handover
Quick
Handover Offset
(dB)
is started.
In P measurement reports, N measurement results meet handover requirements. Handover is
started.This parameter indicates the P in P/N criterion
After the handover succeeds, handover is not allowed within the time this parameter sets.
This parameter indicates the lowest threshold of overlaid subcell level of the handover from underlaid
subcell to overlaid subcell.
This parameter indicates the lowest threshold of overlaid subcell level of the handover from underlaid
subcell
to overlaid handover
subcell from underlaid subcell to overlaid
This parameter indicates the period of
the hierarchical
subcell. When the ratio of overlaid subcell cell channel occupancy is greater than the value of En Iuo Out
ThisGeneral
parameter
indicates
the level
theinload
from
subcell
underlaid
subcell
Cell
OverLoad
Threshold,
allstep
the of
calls
the handover
cell request
for overlaid
handover
at theto
same
time. The
BSC
load is sharply increased, Thus the call may drop because the target cell is congested.Therefore the
algorithm of hierarchical handover is applied to hand over the calls in the cell hierarchically to the
underlaid subcell.
This parameter indicates whether the load handover from overlaid subcell to underlaid subcell is
This parameter indicates the timeallowed.
duration of every hierarchical handover.
If underlaid subcell load is higher than the value of Out Cell Serious OverLoad Threshold, the period of
handover from underlaid subcell cell to overlaid subcell cell is shortened by the value of Out Cell Serious
This parameter
indicates
period
of theonhierarchical
handover
fromLoad
underlaid
subcell to
OverLoad
Threshold
everythe
second
based
the value of
the Out Cell
classification
HOoverlaid
Period.
subcell.
When theindicates
ratio of overlaid
occupancy
is greater
than the subcell
value oftoEn
Iuo Out
This parameter
the levelsubcell
step ofcell
thechannel
hierarchical
handover
from underlaid
overlaid
Cell General OverLoad Threshold, all the calls in the
cell request for handover at the same time. The BSC
subcell
load is sharply increased, Thus the call may drop because the target cell is congested.Therefore the
algorithm of hierarchical handover is applied to hand over the calls in the cell hierarchically to the
underlaid subcell.
When the ratio of underlaid subcell channel occupancy is high, whether some calls in the overlaid subcell
To prevent ping-pong
handover,
thetoBSC
determines
thehierarchical
handover
the MS from overlaid
are allowed
be
overwhether
to of
the
overlaid
subcell.ofhandover.
This parameter
indicates
thehanded
time duration
every
subcell cell to underlaid subcell cell based on the value of this parameter.Suppose the signal strength of
serving cell is SS(s), and neighboring cell SS(n). If the value of SS(s)-SS(n) is smaller than the value of
Distance Between Out And Inn Cell boundary-Distance Hyst Between Out And Inn Cell boundary, the MS
This parameter indicates
distance
between
subcell
and underlaid
subcell. The value of
handoverthe
from
overlaid
subcell the
celloverlaid
to underlaid
subcell
cell is allowed
this parameter is comparative. The greater the value is, the longer the distance is.
If the current system flow level is greater than the value of this parameter, the handover between the
overlaid subcell and underlaid subcell because the underlaid subcell load is too high or too low, is not
If the ratio of the underlaid cell channel occupancy
is greater than the value of this parameter, the
allowed.
period of handover from underlaid subcell to overlaid subcell is reduced by the value of Out Cell Load HO
Modify Step every second based on the value of Out Cell Load Classification HO Period. Thus the
If the ratio of underlaid
subcell
channel
occupancy
greater
than the
valuespeeds
of this up.
parameter, some calls
handover
from
underlaid
subcellisto
the overlaid
subcell
in the underlaid subcell are handed over to the underlaid subcell. Moreover, calls initiated in the overlaid
subcell are preferably assigned to the overlaid subcell.
This parameter indicates whether the channel request in the overlaid subcell is preferably assigned
between overlaid subcell and underlaid subcell according to the Out Cell Low Load Threshold.
This parameter indicates whether the access request initiated in the underlaid subcell is preferably
assigned between overlaid subcell cell and underlaid subcell cell according to the Out Cell Low Load
Threshold.
If the underlaid subcell channel occupancy ratio
is smaller than the value of this parameter, some calls
of the overlaid subcell is handed over to the underlaid subcell. Moreover, the MS that requests for the
overlaid subcell channel is preferably assigned to the underlaid subcell.
This parameter indicates whether the better 3G cell handover algorithm is allowed
During the decision of 3G better cell handover algorithm, 3G better cell handover is originated only when
the period that meets the conditions of the 3G better cell handover algorithm in the measurement period
is greater than 3G Better Cell HO Valid Time
This parameter indicates the measurement time of the 3G better cell handover algorithm
If the Outgoing-RAT HO Allowed parameter is set to Yes and the Better 3G Cell HO Allowed parameter is
Ifset
the
Allowed
parameter
is set
to Yes
and
the of
Better
Cell HO Allowed
parameter
is
toOutgoing-RAT
Yes, better 3GHO
cell
handover
is triggered
when
the
Ec/No
a 3G3G
neighboring
cell is greater
than
set toThreshold
Yes,betterfor
3GBetter
cell handover
triggered
when thewith
RSCP
of a 3G neighboring
greater than
Ec/No
3G CELLisHO
in a period.0-49
0 indicating
-24 dB andcell
63 is
indicating
0 dB
RSCP Threshold for Better 3G CELL HO in a period.
When the Inter-RAT0-63
HO Preference
is set to
2 (2G
cells
with 0 indicating
-115
dBm
andare
63preferentially
indicating -25selected
dBm. according to the
threshold), 3G cells are the preferential selection for handover if the receive level of the first candidate
2G cell is smaller than or equal to HO Preference Threshold for 2G Cell.
This parameter indicates whether a 2G cell or a 3G cell is preferentially selected during cell handover.
Received level threshold of the handover from the UL subcell to the OL subcell of the PS service in the PS
concentric algorithm
Received level threshold of the handover from the OL subcell to the UL subcell of the PS service in the PS
concentric algorithm
This is one of the parameters that determine the regions of overlaid and underlaid subcells. It is invalid
when Enhanced Concentric Cell is allowed:When Enhanced Concentric Cell is not allowed, the regions are
This parameter
the signal RX_LEV
intensityHysteresis,
compensation
between
the overlaid
and underlaid
co-determined
by indicates
RX_LEV Threshold,
RX_QUAL
Threshold,
TA Threshold,
and TA
subcells.It equals the sum of power difference
between overlaid and underlaid power amplifiers,
Hysteresis
insertion loss difference between combiners, path loss difference caused by antennas, and path loss
difference caused by frequencies.
This parameter indicates whether the TA is used to determine a Concentric Cell handover.
This parameter indicates whether the downlink receive level is used to determine a Concentric Cell
handover
This parameter indicates whether the downlink receive quality is used to determine a Concentric Cell
handover
This parameter indicates whether an OL to UL handover is allowed
This parameter indicates whether an underlay (UL) to overlay (OL) handover is allowed
The load threshold for the tight BCCH handover. To initiate the intra-cell tight BCCH handover, the load
should be greater than the threshold.
Signal quality threshold for the tight BCCH handover. To initiate the intra-cell tight BCCH handover, the
downlinkthe
receiving
should
be lower than
thethe
threshold
This parameter indicates
K offsetquality
used for
K Ordering.To
reduce
ping-pong effect during
switchover, the BSC first deducts K Bias from the actual downlink receiving level of a candidate cell.
Then, the BSC performs K ordering over the downlink receiving level of the candidate cell.
This parameter indicates the expected uplink receive level on a new channel after an MS is handed over
to a new
cell. is performed on the neighboring cells of the
This parameter indicates the period during which
penalty
fast moving MS.During this period, penalty on the neighboring cells (on only the other three layers
except
the umbrella
fastinmoving
MS is valid.
This parameter indicates
the penalty
given layer)
to the of
level
a neighboring
cell when an MS is moving
fast.Only the cells in the umbrella layer can give penalty to the cells in other three layers.
This parameter indicates the period for judging whether two continuous intra-cell handovers are
consecutive
This
that starts
when
thresholdintra-cell
of maximum
consecutive
intra-cell
Thisparameter
parameterindicates
indicatesthe
thetimer
maximum
number
of the
consecutive
handovers
allowed.If
the
handovers
is
reached.Intra-cell
handovers
is
allowed
only
when
the
timer
expires
interval of two continuous intra-cell handovers is less than a specified threshold, the two handovers are
regarded as consecutive handovers.
This parameter indicates the threshold for judging whether an MS moves fast across a cell.The threshold
based
the cell
and specified
velocity.
Intra-cell handoverisisobtained
forbidden
if theon
number
ofradius
consecutive
handovers
exceeds this threshold.
If the that
timethe
for actual
crossing
a cell of
is lower
thancells
this that
threshold,
MS
is regarded
as movingtofast.
Suppose
number
the micro
the MSthe
fast
crosses
is N.According
the P/N
rule,when the MS fast crosses N ones among the P micro cells, a fast moving handover is triggered by
During the hierarchical
load
switchover,
the loadsatisfies
switchover
band starts
from Edge HO DL RX_LEV
the BSC
when
this parameter
the required
conditions.
Threshold
a Loadthe
HOMS
Step
LevelP is
added
to the upper threshold
the when
load switchover
every
During theand
moving,
passes
micro
cells.According
to the P/Nof
rule,
the MS fastband
crosses
N
one Load
Step the
Period.
In this
way,
the
BSC
conducts
switchover
level bymicro
level. cell
Finally,
all the calls
onesHO
among
P micro
cells,
the
BSC
starts
to trigger
a fast-moving
handover.
with the receiving level of the current serving cell ranging from Edge HO DL RX_LEV Threshold to Edge
a cell
load is
not smaller
thanHO
Load
HO Threshold,
all the calls
cell
theHO
serving
send
HOIf DL
RX_LEV
Threshold
+ Load
Bandwidth
are switched
over.with
The this
value
of as
Load
Step cell
Level
must
switchover requests simultaneously.
As the
a result,
system
soars.In serious situations, the
be smaller than
valuethe
of Load
HOload
Bandwidth.
congestion may occur to this cell, thus leading to call drop. To avoid call drop, the BSC uses the
The
setting ofload
this switchover
parameter is
relevantto
with
Edgethe
HOnumber
DL RX_LEV
Threshold.A
user is allowed
to initiate
hierarchical
algorithm
control
of users
who experience
switchover
at a
load switchover only when the receiving levelcertain
of the level.
user's current serving cell is within the range from
Edge HO DL RX_LEV Threshold to Edge HO DL RX_LEV Threshold + Load HO Bandwidth.
When the load handover is switched on, it is recommended that the Load HO Threshold is set to 85.
The cell load refers to TCH usage.
When
the
cell
load
exceeds
the
value
HO Threshold,
the
BSC
starts
load handover.
is,
When the load handover is switched on,ofit Load
is recommended
that
the
Load
HO the
Threshold
is set to That
85.When
the
BSC
starts
the
load
handover
after
the
TCH
in
the
cell
are
proportionally
occupied.
System
Flux
Threshold
for
Load
HO
is
obtained
based
on
message
load,
CPU
load,
and
FID
queuing
load.
the cell load exceeds the value of Load HO Threshold, the BSC starts the load handover. That is, the BSC
The systemstarts
flow level
is the
current flow
level
of the
0-11: There
are 12 flow control
the load
handover
aftercontrol
the TCH
in the
cell system.
are proportionally
occupied.
levels.Level 11 is the highest and level 0 is the lowest.
This parameter
indicates
the urgent
uplink quality
for the
HR service.The
values
A load handover
is allowed
onlyswitchover
when the system
flow is control
lower than
thisAMR
threshold.
Otherwise,
of this parameter
matchsituations
quality levels
multiplying
10.
The
urgent switchover
is triggered
unexpected
may 0-7
occur.
Therefore,
this
parameter
must be set
properl) only when
the uplink
receiving
quality
the MSswitchover
is greater downlink
than the switchover
threshold,
receiving
This
parameter
indicates
theofurgent
quality control
for the that
AMRis,
HRthe
service.The
is poor. 10. The urgent switchover is triggered only
values of this parameter match quality levelsquality
0-7 multiplying
when the downlink receiving quality of the MS is greater than the switchover threshold, that is, the
receiving quality is poor.
This parameter indicates the urgent switchover uplink quality control for the AMR FR service.The values
of this parameter match quality levels 0-7 multiplying 10.The urgent switchover is triggered only when
the uplink
receiving
quality
the MSswitchover
is greater downlink
than the switchover
threshold,
receiving
This
parameter
indicates
theofurgent
quality control
for the that
AMRis,
FRthe
service.
The
quality
is poor. 10.The urgent switchover is triggered only
values
of
this
parameter
match
quality
levels
0-7
multiplying
When determining whether to initiate interference switchover, the system compares the difference
when the
quality
ofand
the this
MS is
greater than
that the
is, the
between
thedownlink
receivingreceiving
quality of
the MS
parameter
withthe
theswitchover
switchoverthreshold,
threshold.For
AMR
receiving
quality
is
poor.
calls, this parameter, together with RXQUALn, is used in interference handover decision. An uplink
interference handover is easily triggered if this parameter is set to a smaller value.
Quality threshold 12 for the interference handover of non-AMR FR voice services. The value corresponds
to (quality level 0-7) x 10.
Quality threshold 11 for the interference handover of non-AMR FR voice services. The value corresponds
to (quality level 0-7) x 10.
Quality threshold 10 for the interference handover of non-AMR FR voice services. The value corresponds
to (quality level 0-7) x 10.
Quality threshold 9 for the interference handover of non-AMR FR voice services. The value corresponds
to (quality level 0-7) x 10.
Quality threshold 8 for the interference handover of non-AMR FR voice services. The value corresponds
to (quality level 0-7) x 10.
Quality threshold 7 for the interference handover of non-AMR FR voice services. The value corresponds
to (quality level 0-7) x 10.
Quality threshold 6 for the interference handover of non-AMR FR voice services. The value corresponds
to (quality level 0-7) x 10.
Quality threshold 5 for the interference handover of non-AMR FR voice services. The value corresponds
to (quality level 0-7) x 10.
Quality threshold 4 for the interference handover of non-AMR FR voice services. The value corresponds
to (quality level 0-7) x 10.
Quality threshold 3 for the interference handover of non-AMR FR voice services. The value corresponds
to (quality level 0-7) x 10
Quality threshold 2 for the interference handover of non-AMR FR voice services. The value corresponds
to (quality level 0-7) x 10.
Quality threshold 1 for the interference handover of non-AMR FR voice services. The value corresponds
This parameter indicates the upper threshold
of consecutive
to (quality
level 0-7) xMRs
10 containing no downlink measurement
result for a call.Each call is configured with a global timer, which counts the number of consecutive MRs
containing no downlink measurement. When the timer exceeds this threshold, the handover is disabled
and the timer is reset.
This parameter indicates the uplink receive quality threshold of triggering an emergency handover when
no measurement result on downlink channels is contained in the MR.
This parameter is used to control the handover algorithm without downlink measurement report.If this
parameter
is set
to 0, the
handover
algorithm
downlink
measurement
report
disabled.
This
parameter
indicates
thenogeneral
trend
of a cellwithout
on receiving
levels
within a period.
Youiscan
set this
Therefore,
handover
decision
without
downlink
measurement
report
is
not
allowed
in
this
cell
These
parameters
used
for the levels
configuration
the fast you
dropattempt
filter. They
are used
conjunction
with
parameter
for theare
filter
when
of a cellofplunge.If
to initiate
theinswitchover
upon
the filter
are 9trend
parameters
in total
as filter
parameters.remarkable
In the program,
is
quick
levelparameter
decrease, B,
thewhich
decrease
of cell levels
must
be increasingly
as the10
filter
deducted from
the actual
values
of parameter
A1-A8.C1(nt)
= A1be
x C(nt)
+ A2
x C(nt-t) + A3
x C(nt-2t)
... + A8 x
parameter
B becomes
greater.
This
should
applied
in conjunction
with
the filter+parameters
C(nt-7t),
where:
A1 through
A8.
The parameters A1-A8 of the filter must meet the requirement: A1 + A2 + A3 + A4 + A5 + A6 + A7 + A8
= the
80 fast drop filter. They are used in conjunction with
These parameters are used for the configuration of
the filter parameter B, which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with
the filter parameter B, which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with
the filter parameter B, which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with
the filter parameter B, which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with
the filter parameter B, which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with
the filter parameter B, which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with
the filter parameter B, which are 9 parameters in total as filter parameters.
This parameter
indicates
the receive
downlink
receive
quality threshold
of triggering
an emergency
This parameter
indicates
the uplink
quality
threshold
of triggering
an emergency
handover.When
handover.When
quality
of thethan
downlink
is greater
thanan
DLemergency
Qual Threshold,
an emergency
the
receive qualitythe
of receive
the uplink
is greater
UL Qual
Threshold,
handover
is triggered
handover
triggered.When
frequency
hopping
or DTX
of the
is enabled,
is recommended
due to badisquality.When
frequency
hopping
or DTX
of the
cellcell
is enabled,it
is it
recommended
thatthat
you you
set
set this parameter to 70. When an emergency
handover to
is 70
triggered, inter-cell handover takes priority.
this parameter
AnWhen
intra-cell
handover,
however,
triggered
ifinter-cell
nothe
candidate
cell
istakes
available
andAn
intra-cell
handovers
anone
emergency
handover is
is
triggered,
handover
priority.
intra-cell
handover,are
This is
of the parameters
that
determine
regions
of overlaid
and underlaid
subcells.When
allowed.
however,
is
triggered
if
no
candidate
cell
is
available
and
intra-cell
handovers
are
allowed
Concentric Circles HO Allowed is set to No, the regions are co-determined by RX_LEV Threshold, RX_LEV
Hysteresis, RX_QUAL Threshold, TA Threshold, and TA Hysteresis.
When
Concentric
Circles HO Allowed
set to
Yes, the
regions
are co-determined
Threshold,
By setting
this parameter,
you can is
select
values
from
a measurement
report. Ifby
theRX_QUAL
sender uses
DTX
UtoOthis
HO parameter
Receive Level
Threshold,
HO
Receive
Level Threshold,
TA Threshold,
andselect
TA Hysteresis.
when
is set
to Open,OtoU
select
SUB
from measurement
reports.
Otherwise,
FULL from
measurement reports
This parameter indicates the length of the penalty timer for handover failure between adjacent cells due
to incorrect data configuration.
This parameter indicates the length of the penalty timer for handover failure between adjacent cells due
to failed air interface connection.
This parameter indicates the length of the penalty timer for handover failure between adjacent cells due
to cell congestion
Thisparameter
parameterindicates
indicatesthe
thelength
lengthofofthe
thefilter
filterononthe
theNBR_RCVD_BLOCK
NBR_RCVD_BLOCKsignaling
traffic channel
This
channelwhen
whenthe
the
measurement
report
type
is
EMR.By
setting
this
parameter,
you
can
use
NBR_RCVD_BLOCK
of
measurement report type is EMR.By setting this parameter, you can use NBR_RCVD_BLOCK of multiple
multiple
EMRs, thus
thus
avoiding
inaccuracy
owing
to the
the
use
of
only
one EMR.
EMR handovers. Before
This parameter determines
the
penaltyinaccuracy
time for AMR
full to
rate
touse
halfof
rate
(FR-to-HR)
EMRs,
avoiding
owing
only
one
the timer expires, no AMR FR-to-HR handover request is allowed if the previous full-half handover fails
due to channel
or the
channel
mismatch.
As the MS stays on the signaling
channel unavailability
shorter than on
traffic
channel, this parameter should be
set to a smaller value.
The greater the value of this parameter is, the longer the penalty time after AMR TCHF-H HO fails is. That
This
parameter
indicates
the
length
the
filter
the
REP_QUANT
voice channel
when
the
is, triggering
AMR
handover
becomes
more difficult.
This
parameter
indicates
the
length
ofof
the
filter
onon
the
REP_QUANT
signaling
channel
when
the
measurement
report
type
is
EMR.By
setting
this
parameter,
you
can
use
REP_QUANT
of
multiple
measurement report type is EMR.By setting this parameter, you can use REP_QUANT of multiple EMRs,
EMRs,
thus avoiding
avoiding inaccuracy
inaccuracy owing
owing to
to the
the use
use of
of only
only one
one EMR.
EMR
thus
As the MS stays on the signaling channel shorter than on the traffic channel, this parameter should be
This parameter indicates the number ofset
previous
measurement
reports obtained when you average
to a smaller
value.
CV_BEP of the signaling
duringchannel
the process
forthe
averaging
EMRs.By
setting
this parameter, you
CV_BEPchannel
of the traffic
during
process for
averaging
EMRs
can use CV_BEP of multiple EMRs, thus avoiding inaccuracy owing to the use of only one EMR.
This
indicates
the number
of shorter
previousthan
measurement
reports
obtained
when you should
average
As
theparameter
MS stays on
the signaling
channel
on the traffic
channel,
this parameter
be
This parameter
indicates
the number
ofset
previous
measurement
reports
obtained
when youyou
average
MEAN_BEP
of the traffic
channel
during the
process
for
averaging.By
setting
this parameter,
can use
to a smaller
value
MEAN_BEP
of the of
signaling
during
the process
for averaging
this EMR.
parameter,
MEAN_BEP
multiplechannel
EMRs, thus
avoiding
inaccuracy
owing toEMRs.By
the use setting
of only one
you can use MEAN_BEP of multiple
EMRs,measurement
thus avoiding reports
inaccuracy
owing to the use of only one EMR.
enhanced
(EMRs).
As the MS camps on the signaling channel shorter than on the traffic channel, this parameter should be
This parameter indicates the penalty time
given
the original
set
to a to
smaller
value. serving cell where emergency handover
is performed
due
to TA.serving cell where emergency handover
This parameter indicates the penalty level
given to the
original
is performed due to TA.After emergency handover is performed due to TA, the receive level of the
original serving cell is decreased by the penalty level. Thus, other cells are given higher priority and
handover
the given
original
serving
cell is
not allowed.
Thisparameter
parameterindicates
indicatesthe
the
penaltyto
time
toa
the
original
serving
cell
where
emergency
handover
This
penalty
level
given to
target
cell.A
penalty
level
is given
to a target
cell to
is
performed
due
to
bad
quality.
avoid further attempts when a handover fails due to any of the following reasons:
After emergency handover is performed due to bad quality, the receive level of the original serving cell is
decreased by the penalty level. Thus, other Cell
cellscongestion
are given higher priority and handover to the original
serving cell is not allowed.
A message indicating internal handover refusal is received.
ThisAparameter
indicates the
ofhandover
previous measurement
reports
obtained
when
you
average the
message indicating
Umnumber
interface
failure is received
during
out-going
BSC
handover.
timing advances during the process for averaging the measurement reports.
A message
indicating
Um interface
handover
failure is received
internal
This parameter
indicates
the number
of previous
measurement
reports during
obtained
when handover
you average the
signal strength of adjacent cells during the process for averaging measurement reports
This is Filter Length(How many MR are to be taken) Network will require for decision of SDCCH Qual
HO.TVH HO will initiate depending upon specific no of MR.
This is Filter Length(How many MR are to be taken) Network will require for decision of SDCCH HO.TVH
HO will initiate depending upon specific no of MR.
This is Filter Length(How many MR are to be taken) Network will require for decision of TCH Qual HO.TVH
HO will initiate depending upon specific no of MR.
This is Filter Length(How many MR are to be taken) Network will require for decision of TCH HO.TVH HO
will initiate depending upon specific no of MR.
This parameter indicates the number of measurement reports allowed to be continuously lost in the
interpolation calculation.
If the number of continuously lost measurement reports is not larger than the value, the value of the lost
measurement reports is obtained through the linear interpolation method based on the beginning and
ending values of the continuously lost measurement reports.
This parameter is used to select the candidate cells during directed retry
Otherwise, the lost measurement reports are discarded and the measurement reports are calculated
again
the new reports
arrive.
After the MR is preprocessed by BTS,
thewhen
BTS transfers
the preprocessed
MR to the BSC.This parameter
indicates the frequency that the BTS transfers the preprocessed MR to the BSC
This parameter indicates whether the original BS/MS power class is transferred to the BSC
Determines whether MS will process measurement Report & then send it or just send MR to BTS. If it is
Pre-process then MS must also send Originl MR with that MR
Determines whether MS will process measurement Report & then send it or just send MR to BTS. If it is
Pre-process then MS must also send Originl MR with that MR
This parameter indicates whether the MS uses the optimum transmit power to access a new channel
after the handover.
This parameter indicates whether penalty is given to certain cells, including target cells where handover
fails and serving cells where handover is triggered due to excessive TA or poor signal strength.
This parameter indicates whether an inter-BSC SDCCH handover is allowed. An inter-BSC SDCCH
handover is triggered when an MS succeeds in requesting SDCCH but fails to request TCH in a BSC.
This parameter indicates the minimum interval between two consecutive emergency handovers.
This parameter is used to prevent Ping-Pong HO due to any reason. Any kind of HO is not activated after
time
of first
HO upon new SDCCH assignment and triggers
This parameter indicates the duration of a the
timer,
which
starts
handover
timeout. of
Toaavoid
incorrect
handovers
caused
the inaccurate
measurements
at upon
early
To
indicateupon
the duration
timer,
which starts
upon new
TCHby
assignment
and triggers
handover
stage
of
call
establishment.
timeout. To avoid incorrect handovers caused by the inaccurate measurements at early stage of call
This parameter indicates whetherestablishment.
to switch on/off the concentric DTCB handover.
This parameter indicates P of the P/N criterion for the tight BCCH handover
This parameter indicates N of the P/N criterion for the tight BCCH handover.
This parameter indicates whether an quick handover is allowed.
This parameter indicates the threshold of TCHH to TCHF handover.
This parameter indicates the threshold of a handover from full rate data TCH (TCHF) to half rate data TCH
(TCHH).
This parameter indicates the period that satisfies full rate to half rate handover.
This parameter indicates the time threshold that satisfies full rate to half rate handover.
To indicate whether the handover between the full rate and half rate is allowed or not.
This parameter indicates the lower threshold of downlink receive level when a cell becomes a candidate
cell. receive level when a cell becomes a candidate
This parameter indicates the lower threshold of Uplink
This parameter indicates the Threshold of an inter-layer
or inter-priority handover. It is used to avoid
cell.
This parameter indicates the hysteresis of an inter-layer
or inter-priority handover. It is used to avoid
inter-layer ping-pong handovers.
inter-layer ping-pong handovers.
Actual Inter-layer HO Threshold of a serving cell = Inter-layer HO Threshold-Inter-layer HO hysteresis
Actual Inter-layer HO Threshold of a neighboring cell = Inter-layer HO Threshold + Inter-layer HO
hysteresis
with 0whether
indicating
dBm and 63
indicating
-472G
dBm.
This parameter0-63
indicates
the-110
outgoing-RAT
handover
(from
to 3G) is allowed.
To indicate the period that satisfies the PBGT handover.
To indicate the period when path loss of the neighbouring cells are measured and operator can
determine
whether
PBGT handeover
triggered.
If a cell is ranked 1 of the candidate
cells
for a whole
segment ofismeasurement
period, this cell is called
the
best
cell.
Duration to make the decission of handover by comparing the current serving cell with the best
neighbour cell. This parameter compares the best candidate cell with the current serving cell so as to
decide
whether
a layer
handover.
To trigger an edge handover, the
receive
levelto
of trigger
the uplink
or downlink
should constantly remain lower
than their corresponding edge handover thresholds within Edge HO Watch Time(s). This parameter
indicates this duration.
This parameter indicates the period when uplink/downlink receive levels are measured to determine
whether an edge handover neighbor cell is triggered.
To trigger an edge handover, the receive level of the uplink or downlink should constantly remain lower
than their corresponding edge handover thresholds within Edge HO Watch Time(s). This parameter
indicates this duration.
Compare the candidate cells that are better than the current serving cell so as to decide whether to
To indicatetrigger
the DLaReceive
level threshold
of an edge
handover.
edge handover
willdecision.
be triggered if the
layer handover.
This parameter
indicates
theAn
duration
to make the
downlink receive level is lower than "Edge HO UL RX_LEV Thrsh." for a period longer than Edge HO Valid
Time(s) within Edge HO Watch Time(s).
To indicate the UL receive level threshold of an edge handover. An edge handover will be triggered if the
uplink receive level is constantly lower than "Edge HO UL RX_LEV Thrsh." for a period longer than Edge
HO Validhandover
Time(s) within
Edge An
HOinterference
Watch Time(s).
To indicate whether an interference
is allowed.
handover is triggered when the
receive level is higher than the receive threshold, but the transmission quality is lower than the handover
triggering threshold
This parameter indicates whether a concentric circle handover is allowed ( 900 to 1800 & 1800 to 900 )
The parameter indicates whether a Timing Advance (TA) handover is allowed. A TA handover is triggered
when the TA is higher than the triggering threshold
To indicate whether a Bad quality handover is allowed. BQ handover is triggered when Bit Error Ratio
(BER) over uplink/downlink channels is higher than the triggering threshold.
To indicate whether a fringe handover is allowed. A fringe handover is used to prevent call drops in cell
edges and initiated when the downlink level in the serving cell is lower than Edge HO DL RX_LEV
Threshold or the uplink level in the serving cell is lower than Edge HO UL RX_LEV Threshold.
The parameter indicates whether the layer level handover is allowed. To guide the traffic to the cell that
has high priority.
To indicate whether a power budget handover is allowed. Calculations for the power budget handovers
are based on path loss and search for desired cell in real time and the cell must provide less path loss
and other requirements.
The parameter indicates whether the emergency handover algorithm is allowed. The emergency
handover algorithm is used to prevent call drops when the receive level of the MS drops rapidly
This parameter indicates whether a fast moving handover is allowed. The fast moving handover enables
a fast
movingwhether
MS to hand
overload-sharing
rapidly to a macro
cell,isthus
reducing
handovers.
This parameter
indicates
a traffic
handover
allowed.
Load-sharing
functions only
within the same BSC or in cells of the same layer. It applies to only TCH.
This parameter indicates whether an intra-cell handover is allowed.
To indicate whether handovers between the signalling channels is allowed.
This parameter indicates whether the sequence of candidate cells is adjusted. After the sequence is
adjusted, the handover within the same BSC/MSC takes priority
To indicate the receive quality gain when the number of frequency hopping is 8. The receive quality is
brought out when the cell is configured with the frequency hopping. BSC performs power control based
the gain.
To indicate the receive quality gain when the on
number
of frequency hopping is 7. The receive quality is
brought out when the cell is configured with the frequency hopping. BSC performs power control based
the gain.
To indicate the receive quality gain when the on
number
of frequency hopping is 6. The receive quality is
brought out when the cell is configured with the frequency hopping. BSC performs power control based
the gain.
To indicate the receive quality gain when the on
number
of frequency hopping is 5. The receive quality is
brought out when the cell is configured with the frequency hopping. BSC performs power control based
the gain.
To indicate the receive quality gain when the on
number
of frequency hopping is 4. The receive quality is
brought out when the cell is configured with the frequency hopping. BSC performs power control based
the gain.
To indicate the receive quality gain when the on
number
of frequency hopping is 3. The receive quality is
brought out when the cell is configured with the frequency hopping. BSC performs power control based
the gain.
To indicate the receive quality gain when the on
number
of frequency hopping is 2. The receive quality is
brought out when the cell is configured with the frequency hopping. BSC performs power control based
the gain.
To indicate the receive quality gain when the on
number
of frequency hopping is 1. The receive quality is
brought out when the cell is configured with the frequency hopping. BSC performs power control based
on the gain.
This parameter indicates the maximum permissible adjustment step when the BSC increases uplink
transmit power according to signal quality.
This parameter indicates the maximum permissible adjustment step when the BSC reduces uplink
transmit power according to signal quality.
This parameter indicates the lower threshold of downlink power control quality level of AMR half-rate
traffic channel. When the receive quality is lower than the value of this parameter, the BSC performs HW
IIIof
power
control.
This parameter indicates the upper threshold
uplink
power control quality level of AMR half-rate traffic
channel. When the receive quality is higher than the value of this parameter, the BSC performs HW III
power
control. power control quality level of AMR full-rate
This parameter indicates the lower threshold
of downlink
traffic channel. When the receive quality is lower than the value of this parameter, the BSC performs HW
III of
power
control.
This parameter indicates the upper threshold
uplink
power control quality level of AMR full-rate traffic
channel. When the receive quality is higher than the value of this parameter, the BSC performs HW III
control.power control quality level of half-rate traffic
This parameter indicates the lower thresholdpower
of downlink
channel. When the receive quality is lower than the value of this parameter, the BSC performs HW III
power
control.
This parameter indicates the upper threshold
of uplink
power control quality level of half-rate traffic
channel. When the receive quality is higher than the value of this parameter, the BSC performs HW III
power
control.power control quality level of full-rate traffic
This parameter indicates the lower threshold
of downlink
channel. When the receive quality is lower than the value of this parameter, the BSC performs HW III
power
control.
This parameter indicates the upper threshold
of uplink
power control quality level of full-rate traffic
channel. When the receive quality is higher than the value of this parameter, the BSC performs HW III
power control.
This parameter indicates the lower threshold of uplink power control signal level. When the receive level
is smaller than the value of this parameter, the BSC performs the HW III power control.
This parameter indicates the upper threshold of uplink power control signal level. When the receive level
is higher than the value of this parameter, the BSC performs the HW III power control.
This parameter indicates the step ratio of the quality level adjusted by uplink power control.
This parameter indicates the step ratio of the signal strength adjusted by uplink power control
This parameter indicates the period of the filtering of quality level smooth window through uplink power
control.
This parameter indicates the period of the filtering of signal level smooth window through uplink power
control.
This parameter indicates the period of the filtering quality level index through uplink power control.
This parameter indicates the period of the filtering of signal level index through uplink power control.
This parameter indicates the maximum permissible adjustment step during up power control adjustment
based on signal quality.
This parameter indicates the maximum permissible adjustment step during down power adjustment
based on signal quality.
This parameter indicates the lower threshold of downlink power control quality level of AMR half-rate
traffic channel. When the receive quality is lower than the value of this parameter, the BSC performs HW
III power
control.
This parameter indicates the upper threshold
of downlink
power control quality level of AMR half-rate
traffic channel. When the receive quality is higher than the value of this parameter, the BSC performs
HW IIIofpower
control.
This parameter indicates the lower threshold
downlink
power control quality level of AMR half-rate
traffic channel. When the receive quality is lower than the value of this parameter, the BSC performs HW
III power
control.power control quality level of AMR full-rate
This parameter indicates the upper threshold
of downlink
traffic channel. When the receive quality is higher than the value of this parameter, the BSC performs
HW III
control.
This parameter indicates the lower threshold
ofpower
downlink
power control quality level of half-rate traffic
channel. When the receive quality is lower than the value of this parameter, the BSC performs HW III
power
control.power control quality level of half-rate traffic
This parameter indicates the upper threshold
of downlink
channel. When the receive quality is higher than the value of this parameter, the BSC performs HW III
power
control.power control quality level of full-rate traffic
This parameter indicates the lower threshold
of downlink
channel. When the receive quality is lower than the value of this parameter, the BSC performs HW III
power
control.power control quality level of full-rate traffic
This parameter indicates the upper threshold
of downlink
channel. When the receive quality is higher than the value of this parameter, the BSC performs HW III
power control.
This parameter indicates the lower threshold of downlink power control signal level. When the receive
level is lower than the value of this parameter, the BSC performs the downlink power control.
This parameter indicates the upper threshold of downlink power control signal level. When the receive
level is higher than the value of this parameter, the BSC performs the downlink power control.
This parameter indicates the step ratio of the quality level adjusted by downlink power control.
This parameter indicates the step ratio of the signal strength adjusted by downlink power control.
This parameter indicates the smooth window filter length of quality level through downlink power
control.
This parameter indicates the smooth window filter length of signal level through downlink power control.
This parameter indicates the exponent filter length of quality level through downlink power control.
This parameter indicates the exponent filter length of signal level through downlink power control.
This parameter indicates the maximum number of allowed discarded TCH measurement reports in a
power control period.
This parameter indicates the maximum number of allowed discarded SDCCH measurement reports in a
power control period.
This parameter indicates the shortest interval between two continuous downlink power control
commands
This parameter indicates the shortest interval between two continuous uplink power control commands.
When the number of discarded measurement reports within the power control period is greater than the
value of this parameter, the BSC stops power control.
This parameter indicates the maximum range of dynamic power adjustment for the BTS. If the value of
this parameter is too small, the dynamic power adjustment capability of the BTS is lowered.
During downlink power control, when the quality of received downlink signals is larger than or equal to
DL Qual Bad TrigThreshold, the actual value of DL RX_LEV Upper Threshold is the one plus the value of
DLquality
Qual Bad
Up LEVDiff.
During downlink power control, when the
of received
downlink signals is larger than or equal to
this trigger threshold, the actual value of DL RX_LEV Upper Threshold is the one plus the value of DL
Qual
Bad the
Up LEVDiff
in received
the data downlink
configuration
During downlink power control,
when
quality of
signals is larger than or equal to
DL Qual Bad TrigThreshold, the actual value of DL RX_LEV Upper Threshold is the one plus the value of
Qualof
Bad
Up LEVDiff.
During uplink power control, when the DL
quality
received
uplink signals is larger than or equal to this
trigger threshold, the actual value of DL RX_LEV Upper Threshold is the one plus the value of DL Qual
Bad Up LEVDiff in the data configuration
This parameter determines the maximum permissible adjustment step during power adjustment based
on the quality.
This parameter determines the maximum permissible adjustment step during up power adjustment
based on the level.
In
the
Huawei
II
power
control
algorithm,
qualityadjustment
zones (0, 1-2,
are defined
according to
the
This parameter determines the maximum three
permissible
step3)
during
power adjustment
based
quality of received signals. A maximum permissible
down power adjustment step is set for each quality
on the quality.
zone. This parameter determines the maximum power adjustment step permitted by the level down
power control when the RQ value is quality zone 2 (quality value3) during down power adjustment
the level. step permitted by the level down power
This parameter determines the maximumbased
poweronadjustment
control when the RQ value is quality zone 1 (0 < quality value < 3) during down power adjustment based
on level.
This parameter determines the maximum power adjustment step permitted by power control when the
When the power control step is calculated according
the signal quality, the quality of the received
RQ value to
is 0.
signal has an upper threshold and a lower threshold. When the signal quality exceeds the upper
threshold or is below the lower threshold, power control is performed. This parameter determines the
downlink quality lower threshold for power control
This parameter determines the downlink quality upper threshold for power control.
This parameter determines the lower threshold of the downlink signal for the AMR power control. If the
signal level is below this threshold, calculate an increased value (= (AMR DL RX_LEV Upper Threshold
+AMR
RX_LEV
Lower of
Threshold)/2
- Received
This parameter determines
theDL
upper
threshold
the downlink
signal forLevel).
the AMR power control. If the
signal level exceeds this threshold, calculate a decreased value (= Received Level- (AMR DL RX_LEV
Upper Threshold +AMR DL RX_LEV Lower Threshold)/2).
This parameter determines the uplink quality lower threshold for the AMR power control.
This parameter determines the uplink quality upper threshold of the stable state quality zone.
This parameter determines the lower threshold of the uplink signal for power control. If the signal level is
below this threshold, calculate an increased value (= (AMR UL RX_LEV Upper Threshold +AMR UL RX_LEV
Lowerthreshold
Threshold)/2
- Received
Level).
This parameter determines the upper
of the
uplink signal
for power control. If the signal level
exceeds this threshold, calculate a level adjustment value (=Received Level-(AMR UL RX_LEV Upper
Thresholdthe
+AMR
UL RX_LEV
Lower
In Huawei II power control algorithm,
prediction
function
is Threshold)/2
added in the ).
filter to compensate the dela
of power adjustment. This parameter determines the number of downlink measurement reports for
prediction.
This parameter determines the number of uplink measurement reports for prediction
When this parameter is set to Yes, the Huawei II power control algorithm puts the received measurement
reports
in the
measurement
report compensation
and then
records
the change
transmit
power
When the
network
receives measurement
reports,queue
an average
value
of downlink
signalinquality
values
in
based on the
MS power
and
BTS power
in thethe
measurement
report where the BTS
consecutive measurement
reports
should
bethe
obtained
to reflect
radio environment
locates.
parameter
indicates
the number
of measurement
reports
in which
the quality
average
of thein
When
theThis
network
receives
measurement
reports,
an average value
of uplink
signal
values
downlink
signal
quality
is
taken
before
BTS
power
adjustment.
consecutive measurement reports should be obtained to reflect the radio environment where the MS
locates. This parameter indicates the number of measurement reports in which the average of the uplink
signal quality is taken before MS power adjustment.
This parameter indicates the number of measurement reports in which the average of the downlink
signal strength is taken before BTS power adjustment
This parameter indicates the number of measurement reports in which the average of the uplink signal
strength is taken before AMR MS power adjustment.
Minimum time interval between two continuous AMR power control commands
To indicate the maximum range of dynamic power adjustment for the BTS. Smaller the value, dynamic
adjustment capability of BTS is lowered.
During downlink power control, when the quality of received downlink signals is larger than or equal to
DL Qual Bad TrigThreshold, the actual value of DL RX_LEV Upper Threshold is the one plus the value of
DLquality
Qual Bad
Up LEVDiff.
During downlink power control, when the
of received
downlink signals is larger than or equal to
this trigger threshold, the actual value of DL RX_LEV Upper Threshold is the one plus the value of DL
QualofBad
Up LEVDiff.
During uplink power control, when the quality
received
uplink signals is larger than or equal to UL Qual
Bad TrigThreshold, the actual value of UL RX_LEV Upper Threshold is the one plus the value of UL Qual
BadofUp
LEVDiff.uplink signals is larger than or equal to this
During uplink power control, when the quality
received
trigger threshold, the actual value of UL RX_LEV Upper Threshold is the one plus the value of UL Qual
Bad Up LEVDiff in the data configuration.
This parameter determines the maximum permissible adjustment step during down power adjustment
based on the quality of received signals.
This parameter determines the maximum permissible adjustment step during up power adjustment
based on the level.
This parameter determines the maximum permissible adjustment step during power adjustment based
In the Huawei II power control algorithm, three
quality
zones (0, 1-2, 3) are defined according to the
on the
quality.
quality of received signals. This parameter indicates the maximum power control step permitted when
the received signals are within quality zone 2 (RQ value 3) and when the power is lowered based on
the level.
This parameter indicates the maximum power control step permitted when the received signals are
within quality zone 1 (0 < RQ value < 3) and when the power is lowered based on the level.
After the BSC delivers the power control command, it will be a period before the BSC receives an
This
parameter indicates
the
maximum
powerreports
controllag
step
permitted
when the
signals are
acknowledgement
message.
The
measurement
behind
the changes
in received
the MS received
level
within
quality
zone
2
(1<
RQ
value
<3)
and
when
the
power
is
lowered
based
on
the
level.
and in the MS received signal quality. Thus the power adjustment is delayed. in a short period
of time,
the BSC samples several downlink measurement reports and performs weighted filtering, predicting N
measurement reports after the current time. This parameter indicates the number of downlink
measurement
predicted
by the
The
value of the reports
parameter
equalsby
thethe
previous
number
This parameterreports
indicates
the number
ofBSC.
uplink
measurement
predicted
BSC. The
value N.
of
parameter
previous
number
N.
If this parameter is set the
to Yes,
the BSCequals
or BTSthe
puts
the received
measurement
reports in the
measurement report compensation queue. Then record the change of transmit power based on the MS
To reflect
theBTS
current
radio
environment
where
MS locates,
BSS receive
measurement
reports and
an
power
and the
power
in the
measurement
report.
After values
are added
in the measurement
report,
average value
of uplink
signal
quality
is historical
obtained measurement
in consecutivereport
MR. This
parameter
indicates
compensate
the received
level
value
in the
based
on the change
of the
power.
number of measurement reports in which the average of the downlink signal quality is taken before BTS
power adjustment.
This parameter indicates the number of measurement reports in which the average of the uplink signal
quality is taken before MS power adjustment
This parameter indicates the number of measurement reports in which the average of the downlink
signal strength is taken before BTS power adjustment.
This parameter indicates the number of measurement reports in which the average of the uplink signal
strength is taken before MS power adjustment.
To indicate whether BSC applies HW III power control algorithm. Yes: BSC Applies; NO: BSC does not
apply
In order to calculate the power control according to the signal quality, the quality of the received signal
has upper threshold and lower threshold. This parameter determines the downlink quality lower
threshold for the power control.
This parameter determines the downlink quality upper threshold for the power control.
This parameter determines the lower threshold of the downlink signal for power control. If the signal
level is below this threshold, calculate an increased value (= (DL RX_LEV Upper Threshold+DL RX_LEV
Lower threshold
Threshold)/2
- Received
Level).
This parameter determines the upper
of the
downlink
signal for power control. If the signal
level exceeds this threshold, calculate a decreased value (= Received Level - (DL RX_LEV Upper
Threshold+DL RX_LEV Lower Threshold)/2).
This parameter determines the uplink quality lower threshold for the power control.
This parameter determines the uplink quality upper threshold of the stable state quality zone. The upper
threshold
is larger
or equalUpper
to theThreshold
lower threshold.
The step of power control
is determined
bythan
UL RX_LEV
and UL RX_LEV Lower Thrsh. If
the uplink signal strength is within the range from UL RX_LEV Upper Threshold to UL RX_LEV Lower
Thrsh, power control on the MS is not performed. If the uplink signal strength is beyond the range, power
If the uplink signal strength is within
the range
from
RX_LEV Upper Threshold to UL RX_LEV Lower
control
on the
MS UL
is performed.
Thrsh, power control on the MS is not performed. If the uplink signal strength is beyond the range, power
control on the MS is performed.
Minimum time interval between two continuous power control commands
If the uplink received level difference of calls of the same timeslot exceeds threshold of the difference
between uplink received levels, the situation must be recorded.During the observation of N seconds, if
this
situation
lasts P seconds,
the call of
with
theofhighest
uplink
signalexceeds
intensity
in the timeslot
should be
If the
uplink received
level difference
calls
the same
timeslot
threshold
of the difference
over
to another
timeslot.
between uplink received levels, thehanded
situation
must
be recorded.During
the observation of N seconds, if
this situation lasts P seconds, the call with the highest uplink signal intensity in the timeslot should be
handed over to another timeslot.
The value is 0-1 in fact; however, RRM and CM are multiplied by 10 to prevent floating-point values.
Threshold of the difference between uplink received levels.
This parameter indicates whether the BSC is allowed to assign the half-rate channels and full-rate
channels
the MSchannels
according
the channel
seizure
the concentric
underlaid subcell
andchannel
overlaidseizure
subcell.
The BSCto
assigns
in to
underlaid
subcell
to theratio
MS of
in the
cell. If the
ratio of underlaid subcell is higher than the value of this parameter, half-rate channels are assigned; if
theBSC
channel
seizure
ratioin
ofoverlaid
underlaid
subcell
not
higher
the value
ofIfthis
full-rate
The
assigns
channels
subcell
to is
the
MS
in thethan
concentric
cell.
theparameter,
channel seizure
ratio
channels
are
assigned.
of overlaid subcell is greater than the value of this parameter, half-rate channels are assigned. If the
channel seizure ratio of overlaid subcell is not greater than the value of this parameter, full-rate channels
This parameter indicates whether dynamic are
HSNassigned.
is permissible to use. To reduce the inter frequency
interference
This parameter indicates whether the BSC enables the function of FlexMAIO. When the frequency
hopping and FlexMAIO are enabled in a cell, part of the intra-frequency interferences can be avoided.
To control the Abis resource load threshold. When Abis resource load is lower than this threshold, full rate
channel
is the
assigned.
When the static Abis resource load is greater
than
static Abis load threshold, half-rate channel is
preferably assigned if the dynamic Abis resource load is greater than the value of this parameter; fullrate channel is preferably assigned when if the dynamic Abis resource load is not greater than the value
of this
If the dynamic PDCHs configured in the cell
are parameter.
occupied by the PCU, the BSC periodically reclaims
dynamic PDCHs from the PCU when the CS services of the cell are overloaded.
The channel type to be assigned is decided according to the channel types that are allowed by the MSC
and the percentage of seized TCHs in the cell.
This parameter indicates whether the TCH/H prior function is allowed during the channel assignment.
The timer delays the connection release. It delays the deactivation of channels after main signaling links
are disconnected. The T311 timer starts when the BSC receives the REL_IND message from the BTS. It
ends when it expires and the RF CHAN REL message is sent to the BTS.
The T3109 timer starts when the Channel Release message is sent and ends when the Release Indication
message is received. If the timer expires, channels are deactivated.
The T8 starts when the handover command is sent and ends when the successful handover message is
received. If the timer expires, the out-BSC handover is regarded as unsuccessful
The T3121 timer starts when the handover request is sent and ends when the handover complete
message is received. If the timer expires, the ClearReq message is sent.
The T3107 timer starts when the assignment command is sent and ends when the assignment complete
message is sent. If the timer expires, the assignment fails and the seized channels are released.
The T7 timer starts when the handover request message is sent and ends when the handover response
message is reported. If the timer expires, the outgoing BSC handover fails.
The T3103 timer starts when the intra-BSC handover command is sent and ends when the handover is
complete. If the timer expires, the intra-BSC handover fails.
This timer starts when the CR message is reported and ends when the CC message is received. If the
timer expires, the seized SDCCH is released.
If the timer expires, the seized SDCCH is released. If the reception of the EST IND message expires, the
BSS releases the seized SDCCH.
This parameter indicates the maximum number of paging messages that a cell is allowed to send within
a statistical period.
This parameter indicates the average number of paging messages that a cell is allowed to send within a
statistical period.
This parameter indicates the maximum number of messages in the buffer of the cell paging group
packet when the Cell Paging Message Group Packet Function Switch is turned on.
This parameter indicates the interval between two cell paging group packets, which is an integral
multiple of 50 ms.
The cell paging message packaging is determined by the system load. If the paging message packaging
timer is enabled, the paging messages are packaged according to cells; otherwise, the paging messages
are packaged according to the MTLS.
This parameter indicates the algorithm type of the interference band measurement when frequency scan
is enabled: interference band algorithm I or interference band algorithm II.
This parameter indicates the algorithm type of the interference band measurement when frequency scan
is enabled: interference band algorithm I or interference band algorithm II.
This parameter indicates when BTSs are cascaded, whether the BSC allows the CS service to preempt
the sublink resources of the PS service of the lower-level BTS if the sublink of the BTS cannot be
preempted.
This parameter indicates whether the BSC allows the CS service to preempt the sublink resources of the
PS service.
This parameter indicates whether the BSC forces the MS to send the handover access message.
This parameter indicates whether the MS can be handed over to other channels through assignment
procedure in intra-cell handover.
Every UL frequency is scanned for 10 times. The average of the 10 levels is reported. The result type is
before,
maximum/average
new
If this parameter is main/diversity
set to 0, the call
drop and
caused
by the expirationisof
theadded.
intra-cell handover is not
measured as a call drop. If this parameter is set to 1, the call drop caused by the expiration of the intrais measured
as a call drop.
If this parameter is set to 0, thecell
callhandover
drop caused
by the expiration
of the intra-BSC out-cell handover is
not measured as a call drop. If this parameter is set to 1, the call drop caused by the expiration of the
intra-BSC
handover
as a call
drop.
If this parameter is set
to 0, theout-cell
call drop
caused is
bymeasured
the expiration
of the
out-BSC handover is not
measured as a call drop. If this parameter is set to 1, the call drop caused by the expiration of the outhandover
is measured
a call drop.
If this parameter is set to 0, BSC
the call
drop caused
by the as
expiration
of the into-BSC handover is not
measured as a call drop. If this parameter is set to 1, the call drop caused by the expiration of the intoIf this parameter is set to 0, theBSC
call handover
drop caused
by the resource
check
is not measured as a call drop. If
is measured
as a call
drop.
this parameter is set to 1, the call drop caused by the resource check is measured as a call drop.
this parameter is set to 0, the call drop caused by the unavailability of measurement reports on the MS
for a long time is not measured as a call drop. If this parameter is set to 1, the call drop caused by the
unavailability of measurement reports on the MS for a long time is measured as a call drop.
If this parameter is set to 0, the call drop caused by the forced handover failure is not measured as a call
drop. If this parameter is set to 1, the call drop caused by the forced handover failure is measured as a
callbydrop.
If this parameter is set to 0, the call drop caused
the Abis territorial link failure is not measured as a
call drop. If this parameter is set to 1, the call drop caused by the Abis territorial link failure is measured
as a by
callthe
drop.
If this parameter is set to 0, the call drop caused
Abis territorial link failure is not measured as a
call drop. If this parameter is set to 1, the call drop caused by the Abis territorial link failure is measured
as a call drop.
If this parameter is set to 0, the call drop caused by either of the following factors is not measured as a
this parameter
setcall
to drop
0, thecaused
call drop
by either
of the following
factors
is not
If call
thisdrop,If
parameter
is set to 0, is
the
by caused
other reasons
of connection
failure
(besides
the
measured
as
a
call
drop:
previous four connection failures) is not measured as a call drop. If this parameter is set to 1, the call
drop caused by other reasons of connection failure (besides the previous four connection failures) is
If this parameter is set to 0, the call dropmeasured
caused by
unavailability
of radio resources is not measured
asthe
a call
drop.
as a call drop. If this parameter is set to 1, the call drop caused by the unavailability of radio resources is
measured as a call drop.
If this parameter is set to 0, the call drop caused by the OM intervention is not measured as a call drop.
If this parameter is set to 1, the call drop caused by the OM intervention is measured as a call drop.
If this parameter is set to 0, the call drop caused by the HO access failure is not measured as a call drop.
If this parameter is set to 1, the call drop caused by the HO access failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by the radio link failure is not measured as a call drop.
If this parameter is set to 1, the call drop caused by the radio link failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by the radio link failure is not measured as a call drop.
If this parameter is set to 1, the call drop caused by the radio link failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by the error of unsolicited DM response is not measured
as a call drop. If this parameter is set to 1, the call drop caused by the error of unsolicited DM response is
measured as a call drop.
If this parameter is set to 0, the call drop caused by the T200 timeout is not measured as a call drop. If
this parameter is set to 1, the call drop caused by the T200 timeout is measured as a call drop.
To indicate whether a repeater is present. This parameter influence the handover between the repeaters.
For repeaters that are far away from each other should have asynchronous handovers, otherwise
handovers
will to
bedetect
failed.whether the TRX mutual-aid function is
To indicates the delay time after the cell
initialization
enabled. To delay detecting whether the trx mutual aid function is enabled because the cell that has
been initialized is not in the stable state.
To indicate whether the flow on Abis interface is allowed. When BSS is congested some requests are
rejected or delayed to decrease the system load. This function applies to call management.
To indicate whether half rate is supported in the cell or not. It is one of the cell re-selection parameters in
system message 3.
This parameter indicates the maximum transmit power level of MSs. It is one of the cell re-selection
parameters in system message 3.
This parameter indicates whether the power control function is allowed. It is one of the cell selection
parameters in system message 3.
--BORE, Angle of a trx.
Measuring the average load value timeslots on the RACH.
To indicate the interval between the transmission of an overload message and the retransmission of the
overload message from the BTS to the BSC
TO indicate the load on CCCH timeslot. Overload message is sent to the BSC by BTS if the load on CCCH
is greater than this threshold.
To indicates the interval between the transmission of a load message and the retransmission of the load
message. Used by BTS to inform the BSC about the load on the CCCH timeslot.
Used by BTS to inform the BSC of the interference levels on the idle channels of a TRX. This parameter
This parameter indicates
thethe
value
of frequency
The parameter
of 16 bits. The most
indicates
period
of sendingadjustment.
the RF Resource
indication consists
message.
significant bit indicates whether the parameter is valid. Bits 14-8 indicate the level threshold. Bits 7-0
indicate the BER threshold.
If this parameter is set to Yes, the BTS calculates the speed of the MS with the BTS as the reference
object and reports the speed in the uplink measurement report to the BSC. The value Yes is used for
deciding whether to initiate quick cell switchover.
This parameter is used to detect whether the antenna feeder system connecting the TRX is faulty.
Smaller the value, smaller will be the error and vice versa.
This parameter is used to detect whether the antenna feeder system connecting the TRX is faulty.
Smaller the value, smaller will be the error and vice versa.
Indicates the threshold of the error and triggering condition for the generation of alarm. If the output
power of a trx of a transmitter is lower than a fixed value, an error is generated. Greater the value,
the errorcondition
and vice for
versa.
Indicates the threshold of the errorsmaller
and triggering
the generation of alarm. If the output
power of a trx of a transmitter is lower than a fixed value, an error is generated. Greater the value,
the errorthe
anddifference
vice versa.
This parameter is used for BTS 2Xsmaller
to compensate
between the RSSI when the TMA is
installed and the RSSI when the TMA is not installed and to ensure the accuracy of the RSSI value when
BTS 2X has no TMA. For other BTS version, this parameter is not used.
To indicate the start frame number of the BTS. To Keep synchronization between MS and BTS after BTS is
re-initialized.
This parameter indicates the maximum number of levels that the BTS RF power decreases. It controls
the reduction in the BTS RF power. Higher this value, lower will be BTS RF power and vice versa.
Before the BTS transmits the radio resource indication message to the BSC, the interference levels
measured on idle channels in the period defined by this parameter are averaged.
This parameter indicates the threshold used for the interference measurement. The BSS measures the
uplink quality of the radio channels occupied by the serving MSs, calculates, and reports the interference
level for each of the idle channels. This helps the BSC to assign channels. The measurement result of the
interference bands helps to set variable thresholds and analyze the interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the
uplink quality of the radio channels occupied by the serving MSs, calculates, and reports the interference
level for each of the idle channels. This helps the BSC to assign channels. The measurement result of the
interference bands helps to set variable thresholds and analyze the interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the
uplink quality of the radio channels occupied by the serving MSs, calculates, and reports the interference
level for each of the idle channels. This helps the BSC to assign channels. The measurement result of the
interference bands helps to set variable thresholds and analyze the interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the
uplink quality of the radio channels occupied by the serving MSs, calculates, and reports the interference
level for each of the idle channels. This helps the BSC to assign channels. The measurement result of the
interference bands helps to set variable thresholds and analyze the interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the
uplink quality of the radio channels occupied by the serving MSs, calculates, and reports the interference
level for each of the idle channels. This helps the BSC to assign channels. The measurement result of the
interference bands helps to set variable thresholds and analyze the interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the
uplink quality of the radio channels occupied by the serving MSs, calculates, and reports the interference
level for each of the idle channels. This helps the BSC to assign channels. The measurement result of the
interference bands helps to set variable thresholds and analyze the interference.
If the parameter Assignment Cell Load Judge Enabled is set to Yes, the direct retry process is started and
channels are assigned when the cell supports direct retry and the load of the current cell is equal to or
greater than the value of Cell Direct Try Forbidden Threshold during channel assignment.
Short message of cell broadcast DRX mode. Here, DRX means SMSBC DRX MODE (cell broadcast short
message incontinuous receiving mode). BSC supporting SMSBC DRX must send scheduling message for
MS to receive cell broadcast messages incontinuously. A scheduled message includes many broadcast
messages to be sent in a cell. The duration occupied by the broadcast messages in scheduled message
is called scheduled period. The scheduled message includes both the description of short messages
(arranged in the order of transmission sequence) to be broadcasted and their respective positions in the
scheduled period. Therefore, MS can fetch the wanted broadcast message in the least time, and the
powersupported.
consumption
also decreased.
Indicates the types of data services
Thisisparameter
is set according to the requirements
If this parameter is set to StartUp, the BSC sends the handoff command to the MS and adjusts the
transmission power of the BTS to the maximum. During the handoff, the BSC does not change the BTS
This parameter controls whetherpower
the BTS
reports the
the handoff
voice quality
index (VQI). Voice quality becomes
to ensure
success.
better as the voice level decreases.
In the BTS3002C, the signals transmitted through the primary and secondary antennas are optimized by
Maximum
value
of N3105.supports the configuration of diversity
the low noise amplifier (LNA) bypass circuit.
The
BTS3002C
antennas. That is, the main diversity signals
transmitted
on a DRU are treated by the LNA circuit and
Maximum
value of N3103.
After the a to
downlink
TBF is established,
the network
starts N3105.
then connected
the diversity
port
of of
another
DRU through
a tributary.
Maximum
value
N3101.
GPRS
GSN provides
with
flexible
The QoS levelisiscomplete,
determined
in thethe
subscription.
If the
network
receivessubscribers
the last RLC
data
block QoS
whenmechanism.
the uplink transmission
it sends
MS a Packet
After the
network
set the RRBP
onmultiple
the downlinkcan
RLCshare
data one
block,
it resets
N3105
when
receiving
a blocks
valid packet
In uplink
dynamic
assignment
mode,
uplink
if the
downlink
data
carry the
Uplink
Ack/NackMSs
message
with FAI=1
and channel
starts N3103.
acknowledgment
message
on the
uplinkthe
RLC
data block
to the
RRBP.
Otherwise,
N3105
is added
on the
The QoS control
parameters
include
service
priority
class, reliability
class,
delay
class, and
throughput
class.
USFcorresponding
value.
network side and the network resends the downlink RLC data block where the RRBP is set.
If the network does not receive a packet control acknowledgment message within scheduled time, N3103 is added on
InDuring
version
V9R8,
the
built-in
supports
the
configured
inPacket
theeach
overlaid
or message.
in
the
underlaid
subcell,
and
the
negotiation
of to
a PCU
QoS
profile,
an
MSPDCH
can
apply
a value
for
QoSissubcell
attribute.
After
receiving
the
request
After
the
network
starts
assign
a USF
value
to the
uplink
TBF
(uplink
TBF
established),
N3101
is started.
The
the
network
side
and
the
network
resends
the
Uplink
Ack/Nack
When
N3105
the
starts
T3195.
When
T3195
expires,
the
current
TBF
is released
Upper
limit
of
the
bandwidth
the
Poc
services.
supports
thenetwork
handover
between
overlaid
subcell
and
the
underlaid
from
the waits
MS,
the
network
negotiates
a by
class
for
each
attribute
offor
each
QoS
profile
based
onsubcell.
the
current
effective
GPRS
network
foroverflows,
the
uplink
data
sent
the
MS
on the
reserved
uplink
RLC
block
corresponding
to theabnormally
USF. If the
MS
resources.
The network
provides
QoS
profile
corresponding
resource.
a valid
uplink
RLC
block,
N3101
is negotiated
reset.
Otherwise,
N3101
is the
added
on the
network
side.abnormally.
When this sends
counter
overflows,
the
network
starts
T3169.
When
T3169
expires,
current
TBF
is released
Lower
limit
ofthe
the
bandwidth
for the
Poc with
services.
The
Poc
services
have afrom
strictunderlaid
requirement
on transmission
delay. The
network
should
support
the to
detection
of subcell,
the Poc
Value
range:
Handover
subcell
to overlaid subcell,
Handover
from
overlaid
subcell
underlaid
service type
and take
measures
to Not
reduce
the transmission
delay
to
meet
the requirement
of the Pocand
services.
Handover
between
underlaid
subcell
and
overlaid
subcell,
anduplink
NoThe
handover
between
underlaid
overlaid
Supported:
Not
support
QoS
Optimize
When
this
counter
overflows,
the
current
TBF
is released
The
Poc services
have
a strict
requirement
on transmission
delay.
network
shouldabnormally.
support
thesubcell
detection of
the Poc
Packet assignment
refersDefault
to the assignment
of a packet
channel
to the MS
on the
PACCH.
Packet
assignment involves
subcell.
value:
No handover
between
underlaid
subcell
overlaid
subcell.
This parameter
is based
on
the uplink
immediate
assignment.
service type and
take measures
to reduce
the transmission
delay
to meet
theand
requirement
of the Poc services.
only
move-down
of the
uplink
packet
assignment.
To increase
access
rate of type
MSs, is
after
assignment
Thethe
GRLM
detects the
service
type
carried
in the received
message.
If the service
Poc,the
thepacket
uplink/downlink
Supported:
Support
QoSthe
Optimize
is moved
down to
the BTS,
BSC
reserves
uplink
resources
for
the limit
BTS. of
The BTS
translates
the
downlink
GbrValue
required
bythe
the
ABQP
must be
lower
than
theresources
upper
bandwidth
for
the
Poc a
services
Tobandwidth
increase
access
rate
of MSs,
the
BSS pre-assigns
uplink
TBF
to thethe
BTS.
MSuplink/downlink
sends
channel
The
GRLMthe
detects
the
service
type
carried
in the received
message.
If the service
typeWhen
is Poc,an
the
acknowledgment
message
sent
by
the
MS
to
obtain
the
channel
request
message,
and
assigns
the
reserved
uplink
When both
the MS
and
theby
network
support
PFC,
the
parameters
obtained
from
the ABQP
inPoc
the
PFC.
request,
the
BTS
uses
these
pre-assigned
resources
to QoS
send
the
immediate
assignment
message
the
MS.
After
bandwidth
GbrValue
required
the ABQP
must
be higher
than
the
lower are
limit
of the bandwidth
for to
the
services.
resources
to theMCS
MS. type
Thenused
the MS
can
data blocks.
Default
ondata
the send
downlink.
receiving the immediate assignment message,
the MS
can send
blocks. The BTS also sends a secondary channel
When message
the MS ortothe
does
notMCS
support
PFC,
theused
QoS on
parameters
obtained
from the
DL UNITDAT
of the
request
thenetwork
BSC. After
receiving
this request
message,
the
BSCare
sends
a secondary
immediate
assignment
type
fixedly
the
downlink.
If Downlink Fixed MCS Type
is setSGSN
toto
UNFIXED,
need
set
or from
thecomplete
uplinktorequest
ofparameter
the MS. to determine the MCS type for
message
the
BTS you
to
the this
TBF
establishment.
During
the datathe
transmission
process,
the modulation
scheme
and
coding scheme
can on
be the
changed
transmitting
first TBF. The
MCS types
of the
other
TBFs are
dynamically
adjusted
basis to
of dynamically
the signal
MCS
type
on
theimproving
uplink.
To fixedly
usetoathe
MCS
typetransmission
onDefault
the downlink,
set used
this parameter
to a value
amongofMCS1-MCS9.
adapt
radio
environment,
thus
the quality
links.
transmission
quality.
MCS type fixedly used on the uplink.
If Uplink Fixed MCS
Type is set toadjust
UNFIXED,
you need
to set
this
parameter
to determine
MCS type for transmitting
To dynamically
the MCS
type
on
theand
downlink,
set this
parameterthe
to UNFIXED.
- Setting
effect
Average
period
of bit
error probe.
To fixedly
use aofMCS
the are
uplink,
set this
parameter
tothe
a value
MCS1-MCS9.
the first TBF. The
MCS types
the type
otheron
TBFs
dynamically
adjusted
on
basisamong
of the signal
transmission quality.
Link Adaption (LA): The network dynamically adjusts the coding scheme of a channel based on the transmission
This parameter can
be used to obtain
the
which isset
used
for
the MS to calculate
the measurement
To dynamically
adjust
the forgetting
MCS
type factor,
on the
this
parameter
quality of the channel
link. The link
quality
is determined
by uplink,
8PSK MEAN
BEP
and 8PSKto
CVUNFIXED.
BEP carried in the Packet
Retransmission rate threshold for the
downlink TBF to change from CS4 to CS3.
results.
EGPRS Downlink Ack/Nack message. The network selects a proper coding scheme for transmission based on the
rate
threshold
the
downlink
TBF to change
CS3
to CS2.
measurementRetransmission
reports from the
MS.
For cellsfor
with
good
Um interface
quality,from
the LA
mode
is usually used.
When the retransmission rate of the downlink TBF is greater than or equal to the value of this parameter, the coding
Retransmission
rate
threshold
for
the
downlink
TBF
to
change
from
CS2
to
CS1.
scheme of the downlink TBF changes from CS4 to CS3.
When
the retransmission
thenetwork
downlink
TBF isretransmit
greater than
equal todata
the value
thisthe
parameter,
thecoding
coding
Incremental
Redundancyrate
(IR):ofThe
should
onlyordifferent
blocksofwith
puncturing
Retransmission
rate threshold
for the
downlink
TBF
to change
CS4. combined error
scheme
of information
the downlink
TBF
changes
from
CS3 retransmitted
to from
CS2. CS3 tothrough
scheme.
The
MS
buffers
the
history
and
the
dataor
blocks
When the retransmission rate of the error
downlink
TBF is greater
than
equal are
to the value of this
parameter, the coding
correction. In the cell
with bad scheme
Umrate
interface
theTBF
IR mode
can
achieve
transmission
Retransmission
threshold
for the
downlink
TBF
to change
CS2 to CS3.quality, but the MS
of thequality,
downlink
changes
from
CS2 good
to from
CS1.
When the retransmission
of the downlink
TBF bad
is smaller
than or quality,
equal tothe
theIR
value
of is
this
parameter,
must support rate
this mode.
For cells with
Um interface
mode
usually
used. the coding
Retransmission
rate threshold
for theTBF
downlink
TBF
to change
scheme
of the downlink
changes
from
CS3 to from
CS4. CS1 to CS2.
When the retransmission rate of the downlink TBF is smaller than or equal to the value of this parameter, the coding
CS type TBF
usedchanges
on the downlink.
scheme Default
of the downlink
from CS2 to CS3.
When the retransmission rate of the downlink
TBF
is smaller
than
equal to the value of this parameter, the coding
CS type
fixedly
used on
theordownlink.
scheme of the downlink TBF changes from CS1 to CS2.
If Downlink Fixed CS Type is set to UNFIXED, you need to set this parameter to determine the CS type for transmitting
Youofcan
set
this parameter
to fixedly use a CS on
type onbasis
the downlink.
the
first
TBF.
The
CS
types
the
other
are
dynamically
of the
the retransmission
signal transmission
quality.
Retransmission rate threshold for
the TBFs
uplink
TBF
to change adjusted
from CS4 to the
CS3. When
rate of
the
rate
for the
uplink TBF
change
from CS3
to CS2.
uplink TBF is greaterRetransmission
than or equal to
thethreshold
value of this
parameter,
thetocoding
scheme
of the
uplink TBF changes from
To dynamically adjust the CS type on the downlink, set this parameter to UNFIXED.
CS4
to
CS3.
Retransmission rate threshold for the uplink TBF to change from CS2 to CS1.
When the retransmission rate of the uplink TBF is greater than or equal to the value of this parameter, the coding
scheme
of theTBF
uplinkchange
TBF changes
fromtoCS3
to CS2. the retransmission rate of the
Retransmission
rate threshold
for
theuplink
uplink
from
CS4.
When
the retransmission
rate of
the
TBF isto
greater than
orCS3
equal
to
theWhen
value of this parameter, the coding
rate
for the
uplink
TBF
tocoding
change
from
to CS3.
uplink TBF is smallerRetransmission
than or equal
to
thethreshold
value
of this
parameter,
the
scheme
of the
uplink TBF changes from
scheme
of
the uplink
TBF
changes
from
CS2 to
CS1. CS2
CS4. TBF to change from CS1 to CS2.
Retransmission rate threshold forCS3
theto
uplink
When the retransmission rate of the uplink TBF is smaller than or equal to the value of this parameter, the coding
Default
CS
type
on
the
uplink.
scheme
of the
TBFused
changes
from
CS2 to CS3.
Timer
setuplink
to
release
the
Abis
timeslots.
When the retransmission rate of the uplink
TBF
is
smaller
than
equal
to the value of this parameter, the coding
CS type
fixedly
used
on or
the
uplink.
scheme
of
the
uplink
TBF
changes
from
CS1
to CS2.
Timeryou
set need
to release
the
idle
dynamicto
channel.
If Uplink Fixed CS Type isLevel
set toofUNFIXED,
to
set
this
parameter
determine
the CS type for transmitting the
dynamic
preemption
bytimer
CS services
and PS services
Whenchannel
a channel
is idle, this
is started.
You
can
set TBFs
this parameter
to fixedly
use a on
CS the
typebasis
on the
uplink.
first TBF. The CS types of
the
other
are dynamically
adjusted
of the
signal transmission quality.
If an dynamic channel is no longer used,
it is of
not
releasedreserved
immediately.
a timer is started when the channel is
Number
channels
for CSInstead,
services.
Full-rate
TCHs
theexpires,
dynamic
channels
that can
bereleased.
pre-empted.
When
the are
timer
the
Abis timeslots
are
idle.
To dynamically
thesubcell
CS type
on DCS1800
the
uplink,and
setthe
thisunderlaid
parameter
to UNFIXED.
In a concentric
cell, the adjust
overlaid
uses
subcell
uses GSM900.
If this parameter is set to an excessive value, the PS services are affected.
All dynamic
channelsiscan
be
pre-empted:
The
CS
services
can
pre-empt
all
the
dynamic
channels.
If
this
parameter
set
to
an
excessive
value,
the
idle
Abis
timeslots
cannot
PDCH
downlink
multiplex
Before the timer expires, if there are new
services,
the
dynamicthreshold
channel continues tobe
befully
usedutilized.
and the timer is
Value range:
stopped.
If this parameter is set to a modest value,
the
CS
services
are
affected
when
there
are
too
many
PS services
PDCH
uplink
multiplex
threshold.
Control
cannot
CS
services
can
all the
dynamic
channels
except
for the
If this
is set
to The
a the
modest
value,
the pre-empt
Abis
may
be
frequently.
If thischannels
parameter
is parameter
setbe
to pre-empted:
a lower
value,
TBFs
established
ontimeslots
the PDCH
and
theapplied
subscribers
are fewer,
andcontrol
the
Convert dynamic channel
in underlaid subcell.
channels.
downlink
bandwidth
for each
subscriber
is is
higher.
When
the
timer
expires,
the
dynamic
channel
released.
If this parameter is set to a lower value, the TBFs established on the PDCH and the subscribers are fewer, and the
uplink
bandwidth
for
eachThe
subscriber
is
higher.
Convert
dynamic
channel
in overlaid
subcell.
Dynamic
channelsiscarrying
services
cannot
pre-empted:
services
cannot
theare
dynamic
channels
multiplex
threshold
of dynamic
channel
conversion.
IfIfthis
set
toto
aDownlink
higher
value,
thebe
TBFs
onCS
the
PDCH and
the pre-empt
subscribers
more,
thisthreshold
parameter
is
set
an
excessive
value,
theestablished
dynamic
channel
resources
may
be wasted when
thereand
are the
no
that carry
services.
downlink
bandwidth
for
each
subscriber
is
lower.
services
a
long
time.
Uplink
multiplex
threshold
of
dynamic
channel
conversion.
If this threshold is set
to
a
higher
value,
the
TBFs
established
on
the
PDCH
and
the
subscribers
are
more,
and
the
Convert
dynamic
channel reaches
in both subcells
and underlaid
subcell
preferred.
When the
number
of subscribers
this threshold,
the dynamic
channels
are used.
Multi-frequency
uplink bandwidth
for each reporting.
subscriber is lower.
Value
10
indicates
a
maximum
of
one
TBF
can
be
established
on
the
PDCH.
If this parameter
is
set
to
a
modest
value,
it
is
possible
that
a
dynamic
channel
is
requested
immediately
The
totalthe
number
of
TCHs
and
PDCHs
fixed.
The
PDCH
ratio
PDCHs/(TCHs
+ used.
PDCHs). after being
When
number
of subscribers
reaches
this
threshold,
theequals
dynamic
channels
are
Convert
dynamic
channel
inisit
both
subcells
overlaid
subcell
preferred.
If this
threshold
is high,
is difficult
toand
seize
dynamic
channels.
released.
Therefore,
the dynamic
channel
is sent
frequently.
Value
Value
10 indicates
a maximum
of onerange:
TBF canrequest
be established
on the PDCH.
indicates
a maximum
TBFs
be
established
on the PDCH.
If this parameterValue
is set80
tothis
an excessive
value,
are excessive
PDCHs
andchannels.
insufficient
TCHs. This affects CS
If
threshold
is high,there
itofof
iseight
difficult
tocan
seize
dynamic
Threshold
signal
strength.
If reporting
this threshold
is six
low,
it services.
isHCS
easy
to seize
dynamic
Normal
of the
strongest
cells
respective
of channels
the band
used.
Value
70 indicates
a maximum
of seven
TBFs
can
be established
on the
PDCH.
If this in
threshold
is low,
it threshold
is easy to to
seize
dynamic
channels.
The MS uses the signal strength
the MR and
this
calculate
C31,
which is used for cell reselection.
MSto
shall
report value,
the strongest
cell
in each ofPDCHs
the frequency
bands in
the BA
If this parameterThe
is set
a modest
there are
insufficient
and excessive
TCHs.
Thislists.
affects PS services.
If the threshold of HCS signal strength is high, it is difficult for the cell to be selected.
The MS shall report the two strongest cell in each of the frequency bands in the BA lists.
If the threshold of HCS signal strength is low, it is easy for the cell to be selected.
The MS shall report the three strongest cell in each of the frequency bands in the BA lists.
Maximum duration of the non-DRX mode. DRX_Timer_Max (DRX: discontinuous reception) is a parameter carried by
Timer set for the MS to
wait
the Packet
Uplink Assignment message.
the
cellfor
broadcast
message.
Timer set for the MS to wait for the TBF release after receiving the last data block.
Access burst type used by the MS in the PRACH, PTCCH/U, and packet control acknowledgment message.
Afterthe
theMS
MSswitches
sends the
Packet
Request
or Packet
Ack/Nack
When
from
the Resource
packet transfer
mode
to theDownlink
packet idle
mode, itmessage
stays in carrying
non-DRXChannel
mode forRequest
a period
When the MS receives the last RLC data block carrying the last block flag (FBI=1) and confirms that all the RLC data
T3168
is started
wait
for
the all
Packet
Uplink
Assignment
frommode
the network.
of time.Description,
After the TBF
is released,
thetoMS
monitors
the CCCH
blocks
during message
the non-DRX
period and the
8bit:
access
using
the
8-bit
burst.
blocks on the TBF are received, the MS sends the Packet Downlink Ack/Nack message carrying the final
BSC6000 reserves the MS context. The reservation time depends on the smaller value among DRX_Timer_Max and
acknowledgment flag (FAI=1) and starts T3192.
IfNON_DRX_TIMER.
the MS receives the
Packet Uplink Assignment
message
T3168
expires,
T3168 isofreset.
Otherwise,
the MS
negotiated
with
the before
SGSN
during
the
GPRS
MS
and its Operation
value
is
11bit:
access
using
theoperation
11-bit
burst.
Based on the pagingNON_DRX_TIMER
channel used by is
the
system,
the
network
modes
areattach
classifiedthe
into
Network
initiates the PS access
procedure
again
for
four
times. Iftime
the Packet
Uplink
Assignment
message is still not received,
usually high.
Therefore,
the
reservation
actually
depends
on
DRX_TIMER_MAX.
I, releases
Network the
Operation
Mode II,and
andmonitors
Network paging
Operation
Mode III.
When T3192 expires, Mode
the MS
TBF resources
channels.
During the TBF release
the MS regards this uplink TBF establishment as failure.
process, if the MS is in half-duplex
mode
and receives
the
Uplink
command, the MS responds to the
This
parameter
is used
for Packet
the
open
loop Assignment
power
control.
Value
0
indicates
entering
the
DRX
mode
immediately.
When the GS interface iscommand
configured,
Network Operation Mode I is used.
immediately.
If the timer value is short, the time for the MS to decide
that a level.
TBF establishment fails is short. If a TBF establishment
Initial power
ALPHA
is used
for
the
to calculate
the
output
power
the uplink
PDCH.
fails,
average delay
of packet
access
is MS
short,
but the
success
rate
of TBFon
establishment
in bad
radio
environment
Valuethe
1 indicates
entering
the
DRX
mode
second
later.
Value
n
indicates
entering
the
DRX
n seconds
later.
the Gs the
interface
theone
PCCCH
is not
configured,
Network
Mode
IImode
is used.
If the MS doesWhen
not receive
PacketorUplink
Assignment
command during
theOperation
TBF release
process,
the MS enters the
decreases.
In addition,
the the
short
timer value
increases
the probability
of
theside
retransmission
ofuses
the packet
access
This
parameter
determines
expected
receive
signal
strength
on
the
BTS
when
the
MS
GPRS
dynamic
packet
idle mode.Signal
Ifpower
the strength
MS
is in dual
mode,
it enters
the reduced
dedicated
mode.
filter
length
packet
idle mode.
When the
uses
GPRS
control,
thistransfer
parameter
determines
the
level
of the MS
request,
thusMS
increasing
thedynamic
probability
of reassignment
bycontrol.
theinPCU.
Therefore,
many system
resources
aretransmit
wasted. If
power
When the Gs interface is not configured but the
PCCCH
is configured, Network Operation Mode III is used.
power
based
on
the
path
loss.
the timer value is long, the time
for
the
MS
to
decide
that
a
TBF
establishment
fails
is
long.
If
a
TBF
establishment
Signal strength filter length in packet transmission mode.
This
is delay
used when
the MS measures
the
downlink
signal
strength
packet idle mode
and
calculates
Cn of
fails,parameter
the average
of packet
is long,
but
the success
rate
ofpower
TBF in
establishment
in bad
radio
environment
This access
parameter
mainly
affects
the output
of the MS.
the MS output power. The parameter
indicates the relation between Cn and Cn-1.
increases.
This parameter is used
when
the
MS
measures
the
downlink
signal
strength
in
packet
transmission
mode
and
Constant
the interference
filtering
by MS
power
control. for the uplink power
This parameter determines
the of
channel
where the signal
receivestrength
power level
of the
is measured
calculates Cn of the MS output power. The parameter indicates the relation between Cn and Cn-1.
control.
Remarks
None.