Professional Documents
Culture Documents
Basic Troubleshooting PDP PDF
Basic Troubleshooting PDP PDF
Basic Troubleshooting PDP PDF
MAIN TOPICS
INTRODUCTION
Trouble shooting on the PLASMA DISPLAY Panel is done on board
level. This training module shows a number of common faults that can
be encountered in all PDP Televisions.
Plasma panel faults
Scan & Sustain board faults
Common & Sustain board
Address driver board faults
Control Logic board faults
Power Supply Unit
More product specific faults are treated in separate service training modules.
10
11
Power Supply
Vs
+5V
+15V
Vsetup
Vsc
Va
Vs
+5V
+15V
+5Vctrl
Scan
sustain
driver
(Y-sus)
Scan Control
(Control Logic)
Plasma Panel
+5V
+15V
Address driver
(X-sus)
common
sustain
driver
(Z-sus)
Vs
Vsetup
Vsc
+5V
+15V
Va
12
PSU
Common
Common
XX- or
or
Z-SUS
Z-SUS
Y-DRIVE
Y-DRIVE
Top
Top
Y-DRIVE
Y-DRIVE
Bottom
Bottom
X-LEFT
X-LEFT
Control
Control
or
orLogic
Logic
X-Right
X-Right
13
The Control Board receives the LVDS video signal from the
Television part.
The control Board converts this LVDS signal into
Lets first
look for
at the
Control
addressing
and have
controlasignals
the other
boardsBoard
in the
PDP.
Therefore the Control Board has connections to Address,
Scan sustain and Common sustain boards.
14
Control Board
To Scan
To
Common
MCM
Multi Chip Module
Addressing signal
to left board
Addressing signal
to right board
15
Y-Driver
Two Y-driver boards are located on the
left-hand side (looking from the back) of
the TV. Each is supporting half of the
screen. The upper one the top half of the
screen and the lower board the lower half.
The sustain and reset waveform from the
Y-SUS board is passed on via the scan
driver IC's on both Y-boards to the plasma
panel.
In case of a 42 inch screen, 8 scan driver
IC's (4 on each Y-board) are needed to
address every horizontal line (Y sustain
electrode).
Y-driver
Y-SUS
Y-driver
16
Y-waveform
Set-up
Sustain
Scan
17
Flicker noise
Solarization
18
19
20
10
21
22
11
23
24
12
25
26
13
27
28
14
Be careful when replacing the Z-board. Just like the X and Y board the FPC,
which is part of the plasma panel, must be handled with extreme care.
How to replace the Z-board
1.
2.
29
30
15
Power Supply
AC / DC
changes the input AC voltage (100~240V) to DC
voltage (380V)
DC / DC
generates a number of DC voltages from the DC
380V DC:
Low voltages: Stand-By 5V, 5/12/15/30V
High voltages: Va, Vs, Vset-up, -Vy, Vsc
Vsc
Vsetup
-Ve
-Vy
Address Voltage
~70 V
Vs
Sustain Voltage
~180 V
Vset_up
Setup Voltage
~265 V
Vsc
Scan Voltage
~120 V
Vy
Philips CE / Euroservice, L. van der Niet, March 2007, AX67-M07-0026
~-75 V
31
180V (Vs)
75V (Va)
Check X-board
120V (Vsc)
240V (Vsetup)
Y-SUS or PSU
32
16
33
34
17
End of Module
Basic PDP Trouble shooting
35
18