Professional Documents
Culture Documents
Design Results: Preliminary Reinforced Concrete Design Design Code: ACI 318-2005
Design Results: Preliminary Reinforced Concrete Design Design Code: ACI 318-2005
Design Results
Preliminary Reinforced Concrete Design
Design code: ACI 318-2005
_________________________________________________________________________________________________________________________________________________________________________
Load conditions
C1=1.4CM
C2=1.2CM+1.6CV
C3=1.2CM+CV+0.18EX+0.05EZ
C4=1.2CM+CV+0.18EX-0.05EZ
C5=1.2CM+CV-0.18EX+0.05EZ
C6=1.2CM+CV-0.18EX-0.05EZ
C7=1.2CM+CV+0.05EX+0.18EZ
C8=1.2CM+CV+0.05EX-0.18EZ
C9=1.2CM+CV-0.05EX+0.18EZ
C10=1.2CM+CV-0.05EX-0.18EZ
C11=0.9CM+0.18EX+0.05EZ
C12=0.9CM+0.18EX-0.05EZ
C13=0.9CM-0.18EX+0.05EZ
C14=0.9CM-0.18EX-0.05EZ
C15=0.9CM+0.05EX+0.18EZ
C16=0.9CM+0.05EX-0.18EZ
C17=0.9CM-0.05EX+0.18EZ
C18=0.9CM-0.05EX-0.18EZ
BEAMS
BEAM
A.left
A.cent
A.right
I.P.left
I.P.rght
SKIN
RcBeamM 20x20cm
1.00
0.00
0.00
0.56
1.00
0.00
0.61
0.59
2.23
2.25
0.00
#3
7.50
7.50
7.50
0.23
-0.47
0.85
0.00
2.84
20
TOP:
BOT:
RcBeamM 20x20cm
1.00
0.00
0.00
0.56
1.00
0.00
0.61
0.59
2.23
2.25
0.00
#3
7.50
7.50
7.50
0.23
-0.47
0.85
0.00
2.84
Page1
_________________________________________________________________________________________________________________________________________________________________________
BEAMS
BEAM
A.left
A.cent
A.right
I.P.left
I.P.rght
SKIN
RcBeamM 20x20cm
1.00
0.00
0.00
0.56
1.00
0.00
0.61
0.59
2.23
2.25
0.00
#3
7.50
7.50
7.50
0.23
-0.47
0.85
0.00
2.84
42
TOP:
BOT:
RcBeamM 20x20cm
1.00
0.00
0.00
0.56
1.00
0.00
0.61
0.59
2.23
2.25
0.00
#3
7.50
7.50
7.50
0.23
-0.47
0.85
0.00
2.84
43
TOP:
BOT:
RcBeamM 20x20cm
6.14
0.00
1.50
3.00
6.14
1.50
1.53
1.52
5.69
5.70
0.00
#3
7.50
7.50
7.50
>[]<
1.51
-3.02
2.37
0.00
7.22
44
TOP:
BOT:
RcBeamM 20x20cm
0.37
0.00
0.00
0.00
0.37
0.00
0.35
0.34
1.30
1.31
0.00
#3
7.50
7.50
7.50
0.08
-0.16
0.43
0.00
1.65
45
TOP:
BOT:
RcBeamM 20x20cm
6.14
0.00
1.50
3.00
6.14
1.50
1.53
1.52
5.69
5.70
0.00
#3
7.50
7.50
7.50
>[]<
1.51
-3.02
2.37
0.00
7.22
46
TOP:
BOT:
RcBeamM 20x20cm
0.37
0.00
0.00
0.00
0.37
0.00
0.35
0.34
1.30
1.31
0.00
#3
7.50
7.50
7.50
0.08
-0.16
0.43
0.00
1.65
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Notes.General information:
- Only selected members are shown.
- Deflection should be verified by user.
- Equivalent rectangular stress block is assumed for concrete beam and column design.
Page2
_________________________________________________________________________________________________________________________________________________________________________
Beams:
- V3, M22 and axial forces are ignored in beam member design.
- Only rectangular and T sections are designed.
- Type: U= opened stirrup []= closed stirrup >[]<= has compression reinforcement.
- Left is J beam node. Right is K beam node.
- IP left (inflection point) is the distance from J node to inflection point.
- IP right (inflection point) is the distance from K node to inflection point.
- Stirrup spacing is given for: 0%-25%, 25%-75%, and 75%-100%
- M min/max are maximum and minimum bending moments found for this beam.
- Skin is required reinforcement to resist torsion. Half the area should lie at each vertical face.
Columns:
- Torsion is ignored.
- Only rectangular and circular sections are designed.
- Columns are verified at 2 stations: top and bottom ends.
- Sway magnifier factors for members due to bending moments are ignored.
- Analyze with P-Delta to consider slenderness in the design of columns.
Important:
- Required areas are calculated according to the section reinforcement distribution in database (LEO). Default sections in database have 5 reinforcement bars per side.
Page3