Professional Documents
Culture Documents
Lab No 06 Full Wave Bridge Rectifier
Lab No 06 Full Wave Bridge Rectifier
University
Department of Electrical Engineering
Electronic Devices and Circuits
Lab Manual 6
1|Page
Roll No.
Session
Signature:________________________
Lab Engineer 1
Name: Engr.Yasir Manzoor
Semester:
Signature:________________________
Lab Engineer 2
Name: Engr.Zafarullah
Date
Signature:________________________
Contents
6
6.8
6.9
INTRODUCTION: .........................................................................................................................................4
OBJECTIVE .................................................................................................................................................4
EQUIPMENT ...............................................................................................................................................4
CONDUCT OF LAB .......................................................................................................................................4
THEORY AND WORKING ...............................................................................................................................4
PERFORMANCE PARAMETERS FOR TWO PULSE RECTIFIER ANALYSIS ......................................................................5
PROCEDURE: ..............................................................................................................................................6
Without Filter ...............................................................................................................................6
With Capacitor Filter ....................................................................................................................9
TROUBLESHOOTING EXERCISE......................................................................................................................10
Diode short circuited ..................................................................................................................10
Diode open circuited ...................................................................................................................11
Full wave bridge rectifier with function generator .....................................................................12
STUDENT LEARNING OUTCOME ...................................................................................................................13
1
2
3
4
5
3|Page
6.2 Objective
1.
2.
3.
4.
5.
6.3 Equipment
1.
2.
3.
4.
5.
6.
7.
8.
9.
Function Generator
Digital Multimeter
Oscilloscope
Transformer 220V to 12V
Diode 1N4007
Resistance 330 / 0.5W, 470, 680, 820, 1K, 2.2K, 3.3K, 4.7K, 6.8K, 10K,100K
Capacitance 0.1uF,1uF,2.2uF,10uF,47uF,56uF,68uF,100uF,220uF,330uF
Breadboard
Connecting wires
4|Page
Figure 1 full wave bridge rectifier during positive half cycle D1 and D2 conducts
When the input cycle is negative as in figure 2, diodes D3 and D4 are forward biased and
conduct current in the same direction through RL as during the positive half-cycle. During the
negative half-cycle, D1 and D2 are reverse-biased. A full-wave rectified output voltage appears
across RL as a result of this action.
Figure 2 full wave bridge rectifier during negative half cycle D3 and D4 conducts
6.6.1.2
6.6.1.3
5|Page
IDC
6.6.1.4
( sin()) =
=
0
2
Irms
Vrms
= VDC IDC =
PDC
PAC
4Vm 2
2 R
Vm 2
=
2R
= 81%
Vrms
VDC
=1.11
Pload = Irms 2 R
6.7 Procedure:
Without Filter
1.
2.
3.
4.
Sr.No
Load Resistance
330 / 0.5 W
470
680
820
1K
3.3 K
4.7 K
6.8 K
10 K
10
100 K
No Load voltage_________________
% Of Voltage
Output Voltage
Ripple Factor
Regulation
Vac
Vdc
100
7|Page
8|Page
S.No
0.1uF
1uF
2.2uF
10uF
47uF
56uF
68uF
100uF
220uF
10
330uF
Vr(max)
Vr(min)
Vr(p-p)=Vr(max)-Vr(min)
( )/2
2
9|Page
Vdc
Ripple
Factor
Reason:
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
6.8.1.2 D3 short circuited
Short the D3 using jumper wire and draw the output wave form obtained on oscilloscope.
Write reason for distorted waveform.
10 | P a g e
Reason:
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
Reason:
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
6.8.2.2 D4 open circuited
Open the D4 and draw the output wave form obtained on oscilloscope. Write reason for
distorted waveform.
Reason:
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
11 | P a g e
Reasons:
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
12 | P a g e
13 | P a g e