Professional Documents
Culture Documents
Layer 3 Messages
Layer 3 Messages
Layer 3 Messages
Paging Messages
1 Paging Type 1
1. 2 TMSI Combination
2. 1 TMSI & 1 IMSI Combination
3. 2 IMSI Combination
2 Paging Type 2
1. 2 TMSI & 1 IMSI Combination
2. 3 TMSI Combination
3 Paging Type 3
Other L3 Messages
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Created by Jayadevan.N
jayadevan.nirmalan@adacellworks.com
www.adacellworks.com
Note: In this presentation the BTS & BSC is considered together as BSS part.
MS
BSS
HLR
Channel Request
Immediate Assignment
CM Sevice Request
Complete Layer 3 Info
Authentication Request
Authentication Response
Cipher Mode CMD
Ciphering Mode Command
Cipher Mode Complete
Cipher Mode Complete
Setup
Identity Request
Identity Response
Call Proceeding
Assignment Request
Assignment Command
Assignment Complete
Assignment Complete
Initial Address Message (IAM)
Address Complete Message (ACM)
Alerting
Answer Signal/Answer Message (ANM)
Connect
Connect Acknowledge
PSTN
MS
BSS
HLR
PSTN
Send Routing Info
Connect
Connect Acknowledge
MS
BSS
old
VLR
HLR
Channel Request
Immediate Assignment
Location Update Request
Complete Layer 3 Info
Send Authentication para
Authentication Para
Authentication Request
Authentication Response
Update Location
Insert Subsciber data
Sub data insertion acc
Location Update Accept
Cancel Location
TMSI Realloc Command
Loc cancell accept
TMSI Realloc Complete
Location Update Accept
Note:
This message normally for the Cell channel Informations. This will give the no of
frequencies allocated for the particular cell. In hopping case this will indicate the
frequencies in the MAL list along with the BCCH frequency. In non hopping case will
indicate the TCH & BCCH frequencies.
Note:
This message gives the information about the neighbor frequencies in the idle mode.
Will only gives the BCCH of the neighbors defined. And the NCC permitted parameter
allows the mobile to restrict the neighbors to be sent in the measurement report.
Note:
This message gives the information about the CBCH for the mobile to decode the
CBCH. Along with the other cell level details like LAC, RACH control parameters
etc..
Note:
This message gives the information about the neighbor frequencies in the dedicated
mode. Will only gives the BCCH of the neighbors defined.
1. Channel Request
go back
2. Immediate Assignment
go back
3. CM Service Request
go back
4.Authentication Request
go back
5. Authentication Response
go back
go back
go back
8. Setup
go back
Point 2:
In this message only the mobile forward the called number to the sys
9. Identity Request
go back
go back
go back
go back
go back
14. Alerting
go back
15. Connect
go back
go back
Point 1
Once the Mobile sends the RACH it tries to decode all
the AGCH information and waits for the Immediate
assignment targeted to the particular mobile. It is
being identified from the Establishment cause and
Random reference.
In this message only the mobile forward the called number to the system.
1. Paging to the MS
go back
2. Channel Request
go back
3. Immediate Assignment
go back
4. Paging Response
go back
go back
go back
7. Identity Request
go back
8. Identity Response
go back
9. Setup
go back
go back
go back
go back
13. Alerting
go back
14. Connect
go back
go back
SMS Request
Measurement Report 1
Measurement Report 2
Measurement Report 3
Measurement Report 4
Measurement Report 5
Measurement Report 6
Measurement Report 7
Measurement Report 8
Measurement Report 9
Measurement Report 10
Measurement Report 11
Measurement Report 12
Measurement Report 13
Measurement Report 14
Measurement Report 15
Handover Command
Handover Access
Physical Information
Handover Complete
Physical Information
Channel Request
Immediate Assignment
Authentication Request
Authentication Response
Note:
This is scheduled to allocate SDCCH for 2 mobiles
simultaneously.
Release
Release Complete
Channel Release
Measurement Report
Classmark Enquiry
Classmark Change
CM Re-establishment Request
CM Service Reject
CM Service Accept
Note
In dedicated mode or group transmit mode, higher layers can
request the setting of the channel mode.The channel mode
modify procedure allows the network to request the mobile
station to set the channel
mode for one channel. The channel mode covers the coding,
decoding and transcoding mode used on the
indicated channel.