Professional Documents
Culture Documents
Miningobjective
Miningobjective
Miningobjective
Q1. Which cut is used for solid blasting in Indian coal Mines
a) Fan cut b) burn cut c) wedge cut d) drag cut
Q2. Permitted explosives are safe to use because
a) They have less strength b) they have low velocity of detonation c) they do not
produce much noise during blasting d) special chemical are used to extinguish
the spark produced during blasting.
Q3. Burden is the distance between
a) Two blast holes in same row b) distance between two rows c) distance between
first row of blast holes and bench d) none of the above
Q4. Which of the following explosive have maximum strength
a) ANFO b) TNT c) RDX d) Nitroglycerine
Q5. To measure the performance of blasting which factor is calculated
a) Tonnage factor b) space factor c) stripping ratio d) Powder factor
Q6. What is the formula for blast ability?
a) B = c / t
b)B= t / c
c) B = c + t d ) B = c X t
Where B = Blast ability
c = compressive strength
t = tensile strength of a
rock
Q7 As per provision of regulation 170 (1a)(b) of CMR 1957 danger zone is an area
falling a radius of -------a) 100 m b) 150 m c) 200m d) 300m
Q8 While blasting in hot strata the temperature of hole should not exceed
a) 50 c b) 60 c c) 70 c d) 80 c
Q9
Q10 While dealing with Misfire shot the relieving hole is drilled at a distance not less
than
a) 10 m b) 20m c) 30 m d) 40 m
Q11 As per CMR the recapping of rope is done once at least in every
a) 3 month b) 4 months c) 6 months d) 1 year.
Q12 what is the maximum angle of fleet is permissible in winding as per CMR
a) 1 b) 1.5 c) 2 d) 2.5
Q13 a coal seam is said to be of degree III if rate of emission of gas in m3 /te of coal
raised is
a) is equal to 10 b) less than 10 c) more than 10 d) in between 1 to 10
Q 14 reportable injury means any injury other than serious bodily injury, which involves
the enforced absence of injured person from work for a period of
a) 24 hours or more b) 36 hours or more c) 48 hours or more d) 72 hours or more
Q15 When the air and mineral flow is in same direction the ventilation is known as
a) Homotropal ventilation b) antitropal ventilation c) boundary ventilation d0
natural ventilation
Q16 Roof falls are more common if the face is at
a)
b)
c)
d)
Q17 A seam is worked at a depth of 70 mtrs . from surface and the width of the
galleries is 3.2 mtr the dimension of the pillar should not exceed
a)
b)
c)
d)
15.0 mtrs
16.5 mtrs
19.5 mtrs
13.5 mtrs
Q18 In board and pillar panel worked in conjunction with hydraulic stowing extraction
line preferred is
a)
b)
c)
d)
Step diagonal
Diagonal
Steep diagonal
Straight
Sedimentary rocks
Igneous rocks
Metamorphic rocks
Any type of rocks
Q22 In India a coal seam is defined as a thick coal seam if its thickness is
a)
b)
c)
d)
3m or more
3.5 m or more
More than 4.8m
2.5m or more
CO2 + N2
CH4 + CO
CO + CO2
O2 + H2S
Diamond drilling
Burn side boring
Jackhammer drilling
Chilled shot drilling
Koepe winding
Direct haulage
Endless haulage
Drum winding
Fire
Inundation
Explosion
Noxious gases
10
15
5
7.5
4.5 years
14 months
2 years
3.5years
To prevent the passage of flame from inside to the outside of the lamp
To prevent the passage of CH4 from outside to the inside of the lamp
To disperse the combustion gases uniformly
For proper circulation of air current
d) Silica gel
Q33 Self-rescuer can be used upto
a)
b)
c)
d)
________ % of CO
2
3
1.5
2.5
Q34 According to CMR 1957 CH4 % in return airway should not exceed
a)
b)
c)
d)
1%
1.75%
0.75%
1.25%
Q35 the wet bulb temperature in development faces should not exceed
a)
b)
c)
d)
33 C
32.5 C
33.5 C
30 C
Q36 In contiguous seams means the parting between two seams is within
a) 10m
b) 9m
c) 15m
d) 20m
Q37 which of the following instruments is used to measure the cooling power of the air
a)
b)
c)
d)
Anemometer
Velometer
Manometer
Katathermometer
Splicing
Capping
Interlocking
Gassing
Q40 when shot hole is blasted at a quarry face, fracture of rock takes place by
a) Compression shock wave
b) Reflected shock wave
c) Both by compression and tensile
e) By gas pressure
Q41 The minimum accuracy of colliery triangulation survey is aimed at
a)
b)
c)
d)
1 in 5000
1in 7000
1in 10000
1 in 15000
Q42 fast and accurate extension of centerlines in long tunnels can be done by
a)
b)
c)
d)
Miners dial
Theodolite
Laser beam ranger
Strings with chalk marks
Q45 In an underground coal mine the place where explosive is stored in underground is
called as
a)
b)
c)
d)
Reserve station
Shelter
Magazine
None of the above
Q46 for heavy duty crushing on hard material the type of jaw crusher normally selected is
a)
b)
c)
d)
Q47 To separate two finely divided solids from one another the process to be selected is
a)
b)
c)
d)
Floating
Washing
Jigging
None of the above
Hydrothermal
magmatic separation
supergene
None of the above
Underhand only
Overhand only
Both underhand and overhand
None of the above
Q50 If the RQD of the ore and wall rock are low the method of stoping selected will be
a)
b)
c)
d)
Shrinkage
Sublevel caving
Block caving
Cut and fill
d) Sublevel stoping
Q52 In the panel caving system of block caving the contact between the ore and capping
is kept
a)
b)
c)
d)
Horizontal
Inclined
Vertical
None of the above
12.5 mtrs
13.5 mtrs
14.5 mtrs
15.4 mtrs
Q56 RQD is a quantitative index based on core recovery procedure which is determined
by incorporation of only those pieces of core that are
a)
b)
c)
d)
Q57 In a contoured Map if there are higher values in side the loop it indicates
a)
b)
c)
d)
Ridge
Valley
Plane land
None of the above
Q58 The intersection of a vertical line through the observers station with the upper
portion of the celestrial sphere is called
a) Nadir
b) Ceriestrial horizon
c) Zenith
d) None of the above
Q59 the effect of curvature in leveling is an error, which is
a)
b)
c)
d)
Subtractive
Additive
Multiplicative
None of the above
1in 5000
1in 7000
1in 10000
1in 15000
Q61 The earliest indication of the spontaneous heating of coal can be given by
a)
b)
c)
d)
Sweating of strata
Make of CO2
Temperature rise
None of the above
Q62 In an underground coal mine ventilated by 100 HP fan (Air HP) it is required to
double the quantity of air for the purpose of air HP required will be
a)
b)
c)
d)
200 H.P
400 H.P
800 H.P.
600 H.P.
Galena
Sphalerite
Graphite
Pyrite
b) Labor Ministry
c) Ministry of Coal
d) Law Ministry
Q65 lily controller is used for the protection in winder
a)
b)
c)
d)
Over wind
Over speed
Over current
Over load
Q68 LHD is a
a)
b)
c)
d)
Loading machine
Hauling machine
Dumping machine
Loading, hauling and dumping machine
involute
Circular
Cylindrical
Conical
A dry method
An wet method
Combination of two
None of the above
Q71 Notice to regional inspector of mines about occurrence of serious accident is given
in form
a) IV A
b) IV B
c) IV C
d) IV D
Q72 Blasting Gallery method is not suitable for working seam thickness
a)
b)
c)
d)
Less than 7 m
More than 7m
Up to 11m
More than 11m
Q73 The size and speed of rotation being the same the head developed is max in case of
a) an Arial flow fan
b) a backward bladed centrifugal fan
c) a radial bladed centrifugal fan
d) a forward bladed centrifugal fan
Q74 In water gas explosion the two highly explosive gases that are involved are
a)
b)
c)
d)
H2 and CO
N2 and CO
H2 and CO2
O2 and CO
Q75 In an underground working area CH4 and CO2 are normally expected to be found
respectively
a)
b)
c)
d)
Q76 The most important parameter of a dust that governs its physiological effect is
a)
b)
c)
d)
Q77 In a mine a big roof fall has taken place in the mine intake place in main intake
airway. The fan drift water gauge
a) Will remain unaffected
Q79 60 dB + 60dB
a)
b)
c)
d)
120 dB
3600 dB
63 dB
36 dB
Q80 In ventilation network analysis, kirchhoffs first law is used which states
a)
b)
c)
d)
1 amp
2 amp
3 amp
4 amp
Q86 A 10% increase in cross sectional area of a roadway will reduce the resistance
approximately by
a)
b)
c)
d)
10%
20%
30%
40%
Q87 The recommended instrument for the air borne respirable dust sampling in the Indian
mines is
a)
b)
c)
d)
CLP-10
Konimeter
RAM-I
NCB/MRE-113A
Q88 The oxygen concentration in underground mine should not be less than
a)
b)
c)
d)
20.93%
20%
19%
18%
27 cms
38 cms
35 cms
47 cms
a)
b)
c)
d)
0.25 lumans
0.25 lux
0.25 candlas/m2
0.25 foot candlas
Filtration
Thermal precipitation
Optical
Impaction
PETN
Protosorb
Hopcolite
Potassium palladium sulphate
Sonic velocity
Refractive index
Solid gas absorption
Optical
Fineness of dust
Composition of dust
Presence of methane in air
Colour of dust
10C/
10C/
10C/
10C/
20m
92m
38m
72m
**************************************************************