SUBMITTAL DATA
METAL DUCTS
~ All data provided is based on SMACNA standards
Typical Supply, Return, and Exhaust Ducts ~ Sample Configuration.
Rectangular Ducts (S&D - 1” W.G.)
Rectangular Ducts (TDF ~ 1” W.G.)
Rectangular Ducts (S&D - 2” W.G.)
Rectangular Ducts (TDF - 2” W.G.)
Rectangular Ducts (S&D - 3” W.G.)
Rectangular Ducts (TDF - 3” W.G.)
Rectangular Ducts (TDF - 4” W.G.)
Rectangular Ducts (TDF - 6” W.G.)
Rectangular Ducts (TDF - 10" W.G.)
Rectangular Ducts ~ Connector and Seam Types
Standard Duct Sealing Requirements
SMACNA Table ~ Short Radius Vanes
Construction of Short Radius Vanes ~ (SMACNA Illustration)
Tie Rods
Branch Connections
Dual Wall and Single Wall Rectangular Vanes
Hanger Attachments to Structures (SMACNA Illustration)
Liner Fasteners
Liner Installation
Lower Hanger Attachments (SMACNA Ilustration)
Minimum Hanger Sizes for Round Duct (SMACNA Table)
Minimum Size for Rectangular Duct Hangers (SMACNA Table)
Offsets and Transitions
Rectangular Ducts and Fittings
Rectangular Elbows
Rectangular Gooseneck (SMACNA Illustration)
Riser Supports — From Floor (SMACNA Illustration)
Round Duct Elbows (SMACNA Illustration)
Round Fittings
Round Fittings ~ Other
Round Fittings — Other (Continued)
Round Fittings — Other (Continued)
‘Seams ~ Round Duct and Fittings (SMACNA Illustration)
Upper Attachment Devices — Typical (SMACNA Illustration)
Volume Dampers — Single Blade TypeMETAL DUCTSSLOAN LSAVHXY ANV NYNLaEY “A Tdd AS TVOIdAL
syonugna isnvHXa
‘ONY ‘NanLaa ‘ATddNs
131NI LNaWAINOS, .
‘OL YORd LONG LHOIWALS 40 ‘BOs "GAL 9 LVOUMA SHITE
Sua.awvid 19Nd z 40 “NIN
»
nd == 52 == 10
60 S = 0
2
<0
4 = EB
= 3 4
“0 : 2 7
30 8 5 x
g g
20
» 5 tt 5 +
3 3 g g
Z t 3
= 10 3
58 - .
a, ,
ee f 6
Bs 2 5
‘ ‘
3
NUMBER OF SPLITTERS
"No. 1 of3the, No. 1 vane ofa total of3 vanes. ‘No, 2 of 9* Le, No. 2 vane ol total of vanes.
NUMBER OF SHORT RADIUS VANES
WAAGKAY HVAC Duct Construction Standards Metal and Flexible - Second Edition AN{M4 (6.4 evn) TIE ACOS OM INLET & OUTLET
WELDED TO VANES ANO WISIDE FACE OF ELEOW
LOSS COEFFICIENTS FOR USE OF
1, 2,03 VANES DEPENDS On
ASPEGT RATIO (WW) ANO A CURVE
RATIO (CR) WHICH DEFINES VANE
UCCATION IV TERMS OF THROAT
RADIUS, THIS OATA IS INTHE
1990 SMACHA DUCT DESIGN
MANUAL TABLE 14-10 (6) ANO
IN THE ASHAAE HANOBCOK.
Leow OEPTHH NUMBER OF
REQUIRED (nn) TIEROOS:
0-12" (205) NONE
13+ 20" (20- S0e) 1
21-4 (539. 1213) 2
49-64 (1243 - 1626) 3
65 Gor (1651 - 2002] 4
WELD OR RIVET texte
(2.5125132mm)
ANGLE 1* (25 mm) LONG SAME GA. AS DUCTWORK.
resumen
z_\ a 28.m) S ae gs
FOG. (102 mm} (102m)
BRAZE OF ARC WELD TO ELBOW CHEEK,
4* (02 rm) 0.6, OR FASTEN WITH
14 (65 mmm) BOLTS OR RIVETS,
‘SCREW TO RADIUS ELBOW WITH
(MEHIMUM) #10 SHEETHETAL SCRES
18.GA (1.31 men) HEM ALL FOUR
SIDES BEFORE FORMING
‘SPUTTER DETAIL
CONSTRUCTION OF SHORT RADIUS VANES
Corry HVAC Duct Construction Standards Metal and Flexible - Second Edition
AA&A SHEETMETAL CONTRACTORS CORP. 3067 NW 107" AVE
Doral, Florida 33172
Ph: 305.592.2217 Fax: 305.592.2799
TIE RODS
Based On SMACNA Standards
Stamped, galvanized
disc with neoprene
washer secures the
duet wall,
eon mel
ee
Pipe insert is friction fitted Light Walt
with Internal threads Conduit
Each duct section is
tied at both ends
Bolt Assembly
NX, Rubber Washer tae"
v
Duct Wall
112 or 3f4"
Conduit ”SEE VOLUME DAMPERS IN
FIG. 2-1 ANO FiG 2-15,
7
STRAIGHT TAP
BUTT FLANGE OR CUNCH Lock
CLOSE OPENING
AT CORNERS
45 DEGREE ENTRY 0 45°
OPENING CUT
ACCURATELY (SHAPE & SIZE)
@o@K
CONICAL
—_
DOVETAIL
SOWNT
y ewe, 4° (102 men)
(|
‘CORNER FILLER PIECE
OR USE GASKET
CLINGH Lock
UNED_pUCT
CONNECTION
(NO EXPOSED
UNER EDGES)
0, NOT LESS THAN Oz
45" LEAD IN
00 NOT USE CONNECTIONS WITH SCOOPS.
we
EAD
z PROFILE
T cso vanes
NoTcH
BELLNCUTH, FLANGED, ‘SPIN IN
SEE AG. 3-8
FIT ALL CONNECTIONS:
TO AVOID VISIBLE OPENINGS
ANO SECURE. THEN,
SUITABLY FOR_THE PRESSURE CLASS.
ADDITIONAL MECHANICAL FASTENERS “ARE
REQURED FOR 4° W.6. (100 Pa) AND OVER.
BRANCH CONNECTIONS FIG, 2-6
HVAC Duct Construction Standards Metal and Flexible - Second Edition
Wo CLOSED OUTSIDE ‘CLOSED INSIDE
S10 BEARING END BEARING
REQUIRED ON 3° WG.
(750 Pa) CLASS oUCT
AN OVER. OPTIONAL
FIG. AOR B SEE TEXT ON FOR OTHERS
SIDE" ELEVATION VOLUME DAMPERS
VOLUME DAMPERS - SINGLE BLADE TYPE FIG, 2-12
HVAC Duct Construction Standards Metal and Flexible - Second Edition SMAGHA: