Professional Documents
Culture Documents
A Novel Optimization Strategy For Composite Beam Type Landing Gear For Light Aircraft PDF
A Novel Optimization Strategy For Composite Beam Type Landing Gear For Light Aircraft PDF
Edwin Spencer *
United Technologies Aerospace Systems
850 Lagoon Drive
Chula Vista
Ca. 91910
Abstract
Composite beam type landing gear have applications in small light aircraft. A novel optimization
strategy using Nastran finite element models and sol 200 (optimization solution sequence) is
presented in this paper. The analysis criteria are to meet stiffness strength and weight
requirements for multiple landing load cases. The optimization analysis strategy is a novel two
stage approach. In the first stage a shape optimization is carried out on a tapered rectangular
hollow cross section beam finite element model . Each beam element had 8 design variables:
height, width, cap thickness and web thickness at each end of the beam. The design constraints
for the optimization analysis is a specified vertical deflection at the wheel attachment to meet
landing energy absorption criteria and stresses below allowable for all elements for all load
cases. The optimum cross-sections from the beam analysis are used to create a 3D composite
shell finite element model with multiple ply lay-up property regions for the second stage of the
optimization analysis. In the second stage a ply thickness optimization analysis was carried out
on the 3D composite shell finite element model. The design variables are the thicknesses of
zero degree, + / - 45 degree and 90 degree plies for the various property regions. The objective
function for both shape optimization and ply thickness optimization was to minimize weight.
*Currently employed at UTAS, work for this paper was carried out while the author was
formerly employed at MSC Software.
Introduction
Landing gear for small light aircraft need to satisfy minimum weight criteria, strength criteria
with adequate margin of safety against failure and a precisely tuned stiffness or deflection on
landing to absorb the landing energy. Laminate composite structures are ideal for this
application because the material system can be tailored to meet the specific requirements in a
very predictable manner. To design the landing gear structure to meet these requirements
manually by trial and error will be very labor intensive and extremely time consuming. Finite
element laminate composite analysis coupled with optimization techniques offer a robust and
efficient methodology to design a beam type landing gear.
Optimization Concept
A novel two stage optimization strategy using Nastran finite element models and Sol 200
optimization solution sequence has been devised which can be used to design any generic
beam type landing gear for multiple landing load cases. In the first stage the landing gear
structure is modeled with tapered rectangular hollow cross section beam elements (see Figure
1). Each beam has 8 design variables : height, width , cap thickness and web thickness at each
end of the beam which are initially set to nominal values and a shape optimization is carried out
whereby the cross sectional shape can change span-wise as shown on Figure 2 which is a 3D
rendering of the optimized beam structure.
The optimum cross-sections from the beam analysis (Figure 2) are used to create a 3D
composite shell finite element model with multiple ply lay-up property regions (Figure 3 and
Figure 4) for the second stage of the optimization analysis. In the second stage a ply thickness
optimization analysis was carried out on the 3D composite shell finite element model. The
design variables are the thicknesses of zero degree, + / - 45 degree and 90 degree plies for the
various property regions. The objective function for both shape optimization and ply thickness
optimization was to minimize weight.
Figure 1 Tapered Rectangular Hollow Cross Section Shape Optimization Beam Model
Figure 3 3D Composite Shell Finite Element Model Lofted from Optimized Shape Beam
Model
Nastran Sol 200 Cards For Design Response, Design Constraint, Design
Variable and Design Variable to Property Relation
The model has 30 property regions and 6 plies in each region. For each of 6 plies in each of 30 property
regions we need to set up 2 design responses , one for failure index based on normal stresses and the
other failure index based on interlaminar shear stress. Therefore there are 30*6*2 = 360 response
items to set up with Dresp1 cards.
DRESP1,1,FP,
DRESP1,360,FP,
cfailure,PCOMP,,5,1,1
cfailure,PCOMP,,7,6,30
All of these response items ( failure indices) are limited to max value 0f 0.95 with as many DCONSTR
cards ( 360 of them):
DCONSTR,200,1,,0.95
DCONSTR,200,3606,,0.95
Z Displacement of a certain node ( 248123) is set up with another Dresp1 card and constrained to have
max and min value set by another DCONSTR card.
DRESP1,999,ZDISP,DISP,,,3,,248123
DCONSTR,100,999,14.24,14.26
The weight is set up as response number 1000 :
DRESP1,1000,
WEIGHT, WEIGHT,
This is a symmetric layup [ 0/ + - 45 /90]s and there are 30 regions , so there are 30*3 =90 design
variables to set up :
DESVAR,1,TPLY,0.006,0.006,1.0
DESVAR,90,TPLY,0.006,0.006,1.0
There are 90 DVPREL1 cards needed to relate each design variable to a property card ( Pcomp) field
DVPREL1,1,PCOMP,1,13,,,,,+
+,1,1.0
DVPREL1,90,PCOMP,30,23,,,,,+
+,90,1.0
Figure 13 - Max. Bond Failure Index Max. Drag Ultimate Load Case
Figure 14 - Max. Failure Index Max. Side Load Ultimate Load Case
Figure 15- Max. Bond Failure Index Max. Side Load Ultimate Load Case
Figure 16 - Max. Failure Index Max. Vertical Load Ultimate Load Case
Figure 17- Max. Failure Index Max. Vertical Load Ultimate Load Case
Figure 18 Eigen Value buckling Load Factor Max. Side Load Ultimate Load Case
2500
2420
-2230
-2050
2818
3270
-2500
-2490
3068
3840
-2700
-3260
1750
1830
Conclusions
A robust and easy to implement shape/composite ply thickness optimization strategy has been
developed for beam type landing gear to meet stiffness, strength and weight criteria for
multiple landing load cases. The predicted strains from the finite element analysis compared
favorably with strain gauge measurements on a test article. Eigen value buckling analysis was
carried out on the optimized structure independent of the optimization solution. For future
development, the buckling check could be also be included in the optimization routine.