2500/2520 Automatic Tank Gauge ~
Simple and reliable liquid level measurement for bulk storage
applications
Highlights
“+ Low cost, continuous measurement - up 0.2” (€ mr) accuracy
‘+ No power required for continuous operation
‘+ Meets API Chapter 3.18 regulations for inventory control
applications
‘+ Easy 10.224 display - metric or imperial in decimals o fractions
“+ Wide variety of installation kits and materials available
‘+ Mounting for optional transmitters or limit switehes
+2520 ATG High pressure version available - 150, 220 or 300 PSI
‘gauge
‘+ Floats available for standard, interface, or stiling well applications
‘+ ATEX approved fo use in potentially explosive atmospheres
‘+ Optional Negator Cassette for reduced maintenance and
Increased safety
Application
‘The 2500 series of Automatic Tank Gauges (ATG) are mechanically
‘operated, float anc tape instruments designed to provide continuous
liquid leve! measurement in bulk storage applications.
“The measured levlis displayed using 2 dial and counter bult into the
{gaugehead. The 2500 ATG has many product options that allow itto be
installed on the tank roof or atthe tank side (at grade}, which would
facilitate ground level reading by the operator. electronic
transmission of level data or temperature measurement integration is
requited in the control room, then the gauge can be fitted with an
‘optional tank gauging transmitter,
Example Tank Gauging System
2500 ATG (foreground) 2520 ATG (background)
Operation
The 2500/2520 Automatic Tank Gauges (ATG) are designed to
provide continuous liquid level measurement for bulk storage
‘applications.
‘The 2520 High Pressure Automatic Tank Gauge is designed to
provide continuous liquid level measurement of products stored in
Pressurized vessels. The 2520 provides the speciiconsiderations or
‘options for installation on high pressure vessels
‘The level measurement i displayed using a dial and counter built
into the augehead. The gaugehead can be installed on the tankroof
‘or at the tank side (at grade), which would facilitate ground level
reading by the operator If electronic transmission of level data or
‘temperature measurement integration is required inthe contral
room, then the gauge can be fited with an optional tank gauging
‘ransmiter
‘As standard, the 2500 ATG utes a large stainless stee! float thats
attached tothe stainless steel perforated tape to detect the liquid
level. The float follows the liquid evel a it rises an falls due tothe
constant pullback tension provided by a powerful negator spring oF
‘cartridge motor. The precisely perforated tape engages pins on 2
sprocket whee! that in turn drive the counter assembly. Ths simple
‘design ané operation allows the gauge to perform with negligible
‘maintenance throughout its working life.
Due to high pressure conditions, the 2520 ATG utilizes a magnetic
‘drive that operates the dal reading mechanism. This drive provides
‘2 postive seal-off ofthe counter compartment and the transmitter
housing eliminating danger of glass breakage, loss of product and
the escape of vapors, makingit an important safety feature for both
personnel and plant facilities.
For more Information visit www-tankgauging.com2500/2520 ATS
Installation Guidelines
‘rious installation options and accessories are available to sult user
installation requirements. The following information should be used
‘as aguide only please refer to the operation and maintenance
‘manual for complete instalation instructions.
All pats of the gaugehead, tape and float should move freely to
reduce wear and maintenance. Ths section recommends general
considerations when insaling afloat and tape operated tank gauge.
In-service vs. Out-of-service Installations
For in-service and out-o-servce installations, how a guidewire is
anchored at the tank bottom and welding parts to on the tank are
‘major considerations
Floating Roof Tank Installations
In floating roof tank installations ts recommended that gauges be
installed ina floatwel, rather than attaching the tape directly to the
tank root. The floatwell should contain abatfl ta prevent the float
{rom escaping, but also allow sufficient product movement to
‘equalize the liquid level. No tape should be exposed, outside of the
roof or pipework. if any section ofthe tape is currently exposed it
should be replaced with a stainiess steel, flexible cable. This will
reduce measurement error due to winddrift. The connector between
‘the tape and cable should not un aver a conduit elbow (or pulley)
Note! An internal floating rootis often referredtoas "Pan e.g.3
‘one roof tank with 2 pan and floatwell
Guidewires
VVarec recommends guidewire installations for the 2500 and 2520,
[ATGs with standaré guidewire centers of 17" (432 mrn) when a
‘standard 14.5" (368 mm) diameter Type 316 stainless steel hollow
shell float is used. Guidewires provide stablity forthe float during
turbulent conditions and provide increased accuracy by reducing the
horizontal movement ofthe float across the surface of the product,
‘The guidewires should be installed centered and free of twists or
inks, Check the movement of the float for friction or impended
‘movement before final operation.
Note! Varec recommends guidewire installations or stiling well,
installations where possible,
Guidewire Anchors
\Varec provides two options for tank bottom, guidewire anchors, in-
service and out-of service anchors, The in-service anchor (weight)
hangs from the rof to level just above the tank bottom. The out
‘of service anchor can be welded tothe tank bottom. See the
‘accessories below for further details. Varec top guidewire anchors
‘an be screwed or welded into the tank roof, maintenance hatch or
manhole cover.
‘Support Brackets
"A" frame brackets suppor the conduit (pipework that caries the
tape. These brackets can be welded or bolted tothe tankand should
be placed at regular intervals (approx. 10ft or 3 meters) to provide
uniform support. The pipework should be held rigidly in place and
correctly aligned so thatthe tane does not touch or rub the internal
pipework
Tank Roof Entry
Varec can provide manhole or inspection covers for ease of,
installation and maintenance ofthe float, tape and guidewires. Tape
conduit and guidewire anchor entries into the tank roof should be
‘eat an existing manhole cover or be made through a manhole
cover, See accessories below for further details,
Float Grounding Cable
Varee provides a grounding cable forthe float to prevent the bud
up of static electricity.
‘ares ne.Automatic Tank Gauge
Tas2mai
=== =6
Recommended
24.00"
(610mm)
Maximum
36.00"
(914)
Winimans
18.00"
{406mm
8.00"
{203mm
Layout for conduit supports
(pipework) Spaced at
‘approximately
401 (2m) intervals
|
5.00" 152mm]
Convenient
eye level
Grade
‘ample deals ofa cone rool tank alain, Note tal measurements
may ary depending onthe specific tank type and instalation.
Technical information2500/2520 ATG
Installation Options
Various accessories are provided, depending onthe installation type selected, inthe product order codes.
Cone Roof Tank
Order Code TO1,
1,721, 722,723, 124,734,733, 734 TAD, 742
Installation parts supplied include
1
+ Gauge U bottt
+ Guidewire batiom anchor
ow assem (2)
1+ Support beacket (6)
+ oat
+ Guidewire top anchors 2)
Bolted Tank
Order Code Tos, 125
Installation parts supplied include
+ 90° elbow assembly (2)
+ Guisewires
+ suppor bracket assembly
4+ Suppor bracket (x7)
+ Gaugehead and ape
+ Float
+ Guidewire top anchors 2)
+ Tape connector:
+ 1a/2beck lange
Cone Roof Tank with Pan and Floatwell
Order Code 102, 112
Installation parts supplied include:
1+ 90" elbow assembly 2)
+ Gouge U'bottkt
+ support bracket (6)
+ Gougehead and tape/eable
+ Float
+ Tape/eabie connectors
Varee, Ine‘Automatic Tank Gauge
Cone Roof Tank and Pan: No Floatwell
Order Code 107,117
Installation parts supplied include:
190" Etbow assembly 2)
+ Gauge’ botekit
+ suppor bracket 6)
+ Gaugenead ané ape/eabe
+ Tape/eable connectors
‘Tank Top Mounting
Order Code TOs, 114,724, 732
Installation parts supplied include:
+ Gauge’ botekt
+ Guidewie bottom anchor
+ Gaugeheadané tape
+ oat
4+ Guidewiretop anchors 2}
+ Tape connectors
Stilling Well Service Cone Roof Tank 6" Diameter Float.
Order Code 755, 756
Installation parts supplied include,
190" Etbow assembly 2)
+ Gauge’ botekt
+ Guidewie anchor weight
+ Guidewies
+ Suppor bracket 6)
+ Gaugeheadané tape
+ Float
1+ Guidewietop anchors (2)
+ Tape connectors
Floating Roof Tank and Floatwell
Order Code 103,113,
Installation parts supplied include:
+ 0° Ftbow assembly 2)
+ suppor bracket assem
1 Suppor bracket 6)
‘+ Gaugened ans tape/cabe
+ Float
+ Tapefeable connectors
Technical information2500/2520 ATG
Floating Roof Tank: No Floatwell
Order Code TO6, 726
Installation parts supplied include
1+ 90° Elvow assembly 2)
+ Gauge U bottt
+ Suppor bracket assembly
1+ Suppor bracket (6)
+ Gaugenead and tape/eable
+ Tapeleable connectors
Interface Service
Order Code T51, 152,753, 754
Installation parts supplied include
ow aesemby (2)
+ Guidewir botiom anchor
+ Guisewires
+ Suppor bracket (6)
+ Gaugenead and ape
+ nertace at
+ Guidewire top anchors 2)
+ Tape conn
Sphere Tank to 16ft (4.9 m) or Horizontal Cylinder Tanks
2520 ATG Order Code T01, TO
Installation parts supplied include
+90 elbow assembly 2)
+ Guidewirebatiom anchor
+ Suppor bracket (2)
+ Gougehead and tape
+ Guidewire top anchors 2)
+ Mrcbraciet
Sphere Tank to 48ft (14.6 m) or Horizontal Cylinder Tanks
2520 ATG Order Code T02, 706 - Installation parts supplied include:
+ 90° elbow assembly st)
+45" elbow assembly (2)
+ Guldewire batom anchor
+ Support bracket (2)
+ Gougehead and ape
+ Float
+ Guldewire top anchors 2)
+ wrcbracket
CF
Varee, Ine‘Automatic Tank Gauge
‘Top Mounting for Sphere or Horizontal Cylinder Tanks
2520 ATG Order Code T03, 107
Installation parts supplied include:
+ Guidewie bottom anchor
+ Guidewies
‘+ Gaugenead ans ape
+ Float
+ Guidewie top anchors (2)
‘Sphere Tank to 60ft (18.3 m) or Horizontal Cylinder Tanks
2520 ATG Order Code TO4, TO8
Installation parts supplied include:
1+ So Etbow assembly et)
+ 30° Fbow assembly 5)
+ Guidewies
+ suppor bracket (2)
‘+ Gaugenead ans ape
+ Float
+ Guidewie top anchors 62)
+ MTG bracket
Technical information2500/2520 ATS
Model Options
English and Metr
\Varec provides the following three measurement an¢ display
confguratios:
Configurations
+ English fraction
feet/inches/ 6th
English decimal -feet/inches/1oths
+ Metric configurations - meters/10ths/100ths
English reading gauges are manufactured with 3 reversible
{ractional/decimal dal. For example, ifthe customer desires a
decimal level display, the dal can be removed, reversed and
reinstalled to show decimal units Al diaeounters reflect product
innage. For outage reading requirements, Varec offers 2 conversion
kit (Part #13-08774) for English units of measure only
Check Knob
[An operation checker, provided as a standard feature on both the
2500 and 2520,ATG, permits your technician to check the instrument
for correct operation.
Negator Cassette
‘The negator cassette improves the performance of your mechanical
tank gauge by selFaligning the tape and motor ast provides the
‘constant pullback tension requited for the float to folow the liquid
level. The cassette increases reliability and reduces maintenance by
protecting internal moving parts from pipe debris that could cause
stretching or corrosion It also allows for safer, easier and quicker
service as there sno tape to pullout or negator hubs to unwind in
your hands.
Float Crank
‘The float crank allows your operators to manually aise and lower
‘the loa. This can be useful during turbulent mixing conditions so
‘thatthe float or tape is not damages.
Plug Valve
VVarec recommends the use ofthe 275 Rubber Plug Gate Valve when
installing the 2520 ATG on high pressure vessels. This permits the
user to seal off tank working pressure from the gaugehead and tape
piping system for routine inspection and maintenance. The plug
valves have 14" (38 mm) ANSI RF flanges, Viton-A plug and are rated.
{or either 150 PSI (1034 kPa) or 300 PI (2068 kPa) gauge pressure.
Transmitter Adapters
‘When directly mounting a transmitter or SPDT cam-operate limit
snitch tothe 2520 ATG, Varec recommends the use of a2581 (Oil
Tight) Transmitter Adapter.
Floats
‘The 2500 ATG provided with standard 17° (432mm) lameter Type
316 stainless steel hollow shell float. Depending onthe type of
service kit selected, moderate, severe or extreme, one ofthe floats
‘may be supplied shown in the table below.
‘The 2520 ATG is provided witha standard 8” (203 mm) diameter
‘mult-sphere 36 stainless steel lot, To ensure the highest possible
‘measurement accuracy, the specifi gravity ofthe product being
‘measured is required to properly adjust the weight ofthe float.
Standard 2500 TG fat hollow shel oat (lf), Standard 2520 ATG Mult
sphere lat (idle, 6 interface loa ght)
10
Varee neAutomatic
Tank Gauge
2500 ATG Service Kit Materials
Description ‘Standard Moderate Severe Extreme (N20) xtreme (1,50)
Gauehesd ‘Nuinumy ‘inom ‘astron aston castron
how assembly ‘Aina HOSS, canton Gattiron aston
Top anchors ‘See! HBSS, Stee Stel ‘Sw/Corp. 20
Guidewie weight Steel n1685. 68S. Monel cn.20
Asandardfost
2520 ATG Service Kit Materials
Deserstion Matera
Caugehend Cast cabon eel ASTIN A216, WEB
(Countar housing cover
Ga Auminum
Sprocket, Motor Storage and Tape storage sheaves
Goat Aorinom
‘Negaar spring, Perforated tape and Sprocket Pine
Type 301,303 or BIB aailess eel
Bearnae Sales 8
Floats
art Material Net Weight size
‘8074-000 BESS. 5b aka) 1 (632 me at
122339.000 carp. 20 107 B69 ¥@) 17° (432 mm Fat
1Mi2338-000 ‘Monel 10516 (484g) 1 (422 mm) Fat,
pwizeat 36 ne 203 mm Mult sphere
8237777006 HOSS Depends on specie gravtyet | 8° (208 mm) Sphere interface)
product contact varee
B2a7782 008 es 1 (53 mm Sphere terface}
1737783.006 3655 10" (254 mm Sphere interface)
rae Fibre gas ob 27" (32 mm Flat,
Conduit Elbows
Pare ‘angle | Description Pressure Rating Conduit Materia Wheel Material
eva66 o Ew 1350 PI 2034 a) eae castiron| 3655
evano2 0 Elbow 300 P2068 xP} gage | Castcon ness
v480 = ow 300 P2068 Po) ea Casteon 36s
evaa89 0 ow 300 PS (2068) age | Castron 695
osonsee [90° bow ‘Amosphene ‘Aluminum ebin
osorrs (30° how ‘Atmospheric Alumina 31655
Baers 90" how ‘mosphere Gastron 31658
Bwso7e 3 ow ‘tmospheve 36 Staines tee 3165
eas nas | ebow ‘Nmospherie ‘Alun Delrin
346 180°‘ ebow ‘Amosphene ‘Aluminum Delrin
e623 NA Tope cater ‘Atmospheric ‘Aluinom Debin
Technical information
u2500/2520 ATS
Accessories
Gauge Calibrator Assembly
The Gouge Calibrator allows level A
transmitters with absolute encoders tobe »
> s
calibrated without disassembling the bess “a
‘transmitter from the gaugehead. The Os
calibrators accessed by removing the g
counter assembly cover. By turning the
calibrator, the counter and the transmitter can both be set to the
proper level. The dual calibrator can be retrofitted to existing 2500,
[ATG installations (Part #13-08948),
Condensate Reservoir
‘The condensate reservoirs designed to
collect condensate that would otherwise Fi
accumulate inthe gaugenead. suse is
recommended where an excessive amount
‘of condensate could develop or ino filed
sauge applications (Part #0A8051).
Shock Absorber a
‘The Shock Absorber reduces wear and
maintenance on a 2500 ATG by minimizing A
the transfer of wave energy fom the lotto 4
the perforated tape and gaugehead
‘components. It prevents the float from
becoming detached from the tape by wave
action and should always be used in tanks
‘with turbulent conditions near inlet or outlet
Diping and near a mixer (Part HOAG38).
Manhole Cover —
Guidewire Anchor
Varec can supply two
sifferent guidewire anchors
(also referred to as bottom
anchors or weights),
depending on the installation
type. An anchor that can be
welded to the tank bottom is
see when the tank out-of service (Stee! Part #AA1025) (Stainless
Steel Part #05-08208) or (Monel Part #05-08203).A cast iron weight
can be used as an alternative when the installation is performed
While the tanks in-serviee (Part #BA8482),
Conduit Elbows
Conduit elbows reduce wear on the tape and provide various
installation options, depending on the tank type. Varec can arovide
various angles, materials and low/bigh pressure options.
Conduit Oil Seals
Oil seals designed into the
conduit pipework during
Installation can help reduce
wear andmaintenance on the
tape, conduit and gaugehead
pats. The seals also prevent SJ
theloss of damaging fumes or q
corrosive vapors. Depending 5
‘on the installation, the We
following ol seals are
available:
‘This manhole cover (Model 226) allows for
In-service installation of the 2500 ATG
‘through a tank's existing manway. each or
the three port entries i threaded fr simple
installation of pipework or guidewire
‘anchors. (Part HBM3443 for 20°, Part
{#93607 for 24"),
Inspection Cover
This inspection cover (Model 228) can be
installed onto an existing manhole cover, to
provide an easily removable inspection plate
(Pare #6746}.
Float Grounding Kit
‘The Float Grounding Kit positively grounds
the float to the tape or able (Part # 13
10974),
Roof Weight Kit
‘The roof weight is used in floating roof apalications to reduce the
likely hood thatthe tape/cable is damaged by a sudden roof drop. It
sits on top of the float
(Part # 844580-003),
1 oof and is connected ta the tape/cable
x0.0189¢AaA | Auminum | 8.5 (216mm) Water column ope
pressure
sootsse-aaa | castion | 85" (216mm) Water column operating
pressure
10.02851-AKA | Auminam | 27 (686mm) Water column operating
pressure
Teflon Tape Wipe
Generally used with the conduit vent, the Tape Wipe (Model 25465)
can also be used alone. The Tape Wipe mounts in the conduit
between the top of the tank ané the ist elbow and removes excess
residue from the tape. It minimizes vapor loss from the tank into the
conduit and helps prevent vapors and liquids from contaminating
the gaugehead (Part #8A13924),
2
‘ares ne.Plug Gate Valve
\Varec recommends the use of
the 275 Rubber Plug Gate
Valve when instaling the
2520 ATG on high pressure
vessels. Tis permits the user
to seal off tank working
pressure rom the gaugehead
‘and tape piping system for routine inspection and maintenance. The
plug valves have 1-" (38 mr) ANSI RF flanges and are ated for 150
PSI (2034 kPa) (Part #2752V) or 300 PSI (2068 kPa} (Part #2752V)
gage pressure
Guidewire Top Anchors
Guldewire top anchors provide a point on
the tank roof to connect the guidewire
during installation, The internal spring
provides a constant tension on the
Buidewire, which reduces horizontal
movement ofthe float due to turbulent
conditions. Guidewire top anchors can be
screwed or welded directly onto the tank
roof or into an existing manhole cover.
Automatic Tank Gauge
Negator Cassette
The negatoreasset
Improves the performance of
your mechanical tank gouge
by selfaligning the tape and
‘motor ast provides the
constant pullback tension
requited for the float to
follow the liquid level. The
cassette increases reliability and reduces maintenance by protecting
internal moving pats from pipe debris that could cause stretching or
corrosion It also allows for safer, easier and quicker service as there
is no tape to pull out or negator hubs to unwind in your hands.
‘The negator cassette ft all alumninum Varee 2500 (mode! 8}
‘Automatic Tank Gauge and can be ordered as an option, a Cassette
Kit for negator motor to cassette conversion kit (shown) (Part #13.
110652) ora Cassette Assembly only (Part #06-10368),
Maintenance Kits
‘regular schedule of maintenance is recommended, The frequency
lof such inspections depends on the specific environmental
conditions and operation, Due tothe various conditions, even from
tank to tank on the same site, installations shouldbe studied and a
routine of inspection and maintenance should be planned thats
best sulted to individual needs,
arte Materia Pressure rating
5200 Steel ‘maspherie serision
13-08766 2500 Base Maintenance Ki Engih
emsoas B16 Stainess Stee! | Atmosphere
amae4s steel 250 511034 ka) gage - —
13.08768 2300 Extended Maintenance Kt Ealish
aaea7 Steel 300 512068 ka) ange
5.08769 2500 Extended Malntanance Kt- Matic
‘Support Brackets 13.0870 2500 OverhaulfReturbishing KR Enash
frame brackets support (>)? 3308771 2300 OverhaulRefurbishingKt- Metric
‘the condult (pipework) that
‘artes the tape. The steel Le 3.097900 __| Shoulder Bushing Kk
pipe support brackets used canded fone Wodlcaion Fafa
eee rinerank aee L, 33.0877 Extended Range Modification Kt Ergish
#835643.003) and the upper 33.0877 Extended Range Modification Kt- Metric
support bracket assembly is Side
tised at the tank top (Part {bracket 1308778 (Outage Reading Conversion Kit Engish
wem7s7, 33-08785 2520 ATG Base Maintenance Kt- Metric
13.08787 2520 ATG Overhaul/Refrbishing Kt- Metre
3.07824 English Courter
emnesea English to Metric Conversion Kit
‘awesco Metco English Conversion Kt
13.1087 Fst Grounding Kit
Technical information
B2500/2520 ATS
System Integration
Tank Gauge
Loop
comminentons|
Fusobarager more
‘Sofware
LJ
LJ «LJ
Low Conmuncetion a. Meds
LS.
Communeatens
Control Room ele
at 5 J
SORTS ToOO FT System Da
‘Arange of analog and digital tank gauge transmitters is available that
‘mounts rectly to mechanical tank gauges. Level measurement data
is encoded by the transmitter and output va industry standard
‘communications to the contr room. Some transmitters also offer
spot temperature measurement integration that can be used for
inventory control apolications. When a tank gauge transmitter is
used, communications and power are required atthe gaugehead
\Varec transmitters do nat require an adapted flange. When
connecting third party equipment, a specific adaptor flange,
‘depending on the transmitter, is often required
2557 Alarm Limit Switch
The 2587 Alarm Limit Switch
(ALS) i designed to mount
directly to the 2500
Automatic Tank Gauge (ATG)
or ata conduit elbow. It
provides 2 contact closure or
opening ata pre:set cam
position to allow for alarm
indications. The 2557 ALS is
available with 2,4 or 6
switches that can be used to
activate alarms or relays at
any lev! selected by the user. For further information, refer to
product documentation, itis commended to use 2 2581 (Oil Tight)
Transmitter Adapter (Part #8M19900-200) when directly mounting a
transmitter or SPOT cam-operated limit switch to 22520 ATG,
4
‘ares ne.Automatic Tank Gauge
2910 Float & Tape Transmitter
The 2900 Float & Tape
‘Transmitter (FTT) provides
data from the tankside tothe
‘ontral room for use in
inventory management
volumetric aleuations. The
2910 FTT utilizes an absolute
‘apace encoder to
‘accurately convert the
mechanical level
Technical Specifications
2500 ATG
Product gravity [07191 9/700 9900 kal)
‘lominum — Atmosphere 2.5 PS [72x]
{Cast ton — Atmospheric to 10 51 (6595 kPa}
measurement from the
‘connected tank gauge. The 2910 FTT is als able to integrate a single
temperature sensor and provide cam-operated switches for the
indication of alarms o relays. Level and temperature information is
‘transmitted vi one of the following field communications protocols:
+ Mark space
+ EIA485 MODBUS/GSI Type MODBUS
+ Tankway (L24)
2920 Float & Tape Transmitter
The 2920 Float & Tape trans
side to the control room for use in inventory management
‘applications. It converts mechanical level measurement from the
tank gauge, integrates temperature and HART devices, and provides
ligtal inputs and digital outputs for the indication of alarms or drive
relays. Level and temperature information is transmitted via one of
the folowing field communications protocols:
+ Biphase Mark
+ 14.485 MODBUS/GSI Type MODBUS
£8200 Current Output Transmitter
The 8200 Current Outout
Transmitter (COT) is 3
precision analog transmitter
designed to relay evel
Information via field
‘communications to the
‘ontrl room. The 8200COTIs
designed to provide an
witharisinglevel usinga 420
‘mor 10-50 ma signal, which
varies in direct proportion tothe liquid evel
Gaugingrange | 0-60 RUB)
‘extended ange | 090K (27m) ined roof anks ony requires
“ambient oF te sse0 TF Faa Cte TTS
ranges
‘Materials Dependent on instalation type and pars
selected
‘Shipping weight | 7OTbs (33) (nominal weight increases with
vious)
‘approvals wee
Cerca Number: FOBATExO009
(FT) provides data from the tank es tentona)
2520 ATG
Product gravity | O45 to 069 glee (450-650 kal)
ange specie gravity
Service ating | Atmospheric to 150 PSI 034 KPa) or S00 P51
(20684) ge pressure
‘Gaugingrange | 0- eR GBR)
“Ambient WF io 60 F(a Ce TO
temperature
‘Matera Dependent on installation type and pars selected
‘Shipping weight | 1801bs (62a) t0 250 004)
‘approvals 5 All Medel (optional
150 and 220 Psi (15 Bar) Gauge version conforms
To ATEK class, Zone 2x11 2675) on
Technical information2500/2520 ATS
2500 ATG Order Codes
Notel_ For utagereading, pease spciy "OUT" forexamle N260001-155
(OUT. For outage versions wth metic unit, please contact he factory.
Notel_ For asphalt applications, pease specify "AP, fr example N2S00D-
Note! Foran IP cortfed gouge speify"PES, such as N2S00% TSS IPS.
Notel_Allpaserignate in US. and confor to ATEX; Ex112G,Ta= 40°C
085°C
Note! Foran iron Gaugehesd for usein pressurized apaleavons uote 20
English Configuration
‘Aluminum Gaugehead with Negator Motor
30 Tank Type
}T02 | standars service cone roof tank with pan &
ste
roa | standard service foatng rot tank laste
roa | standard service tank top mounting
708. |standar service floating rot tank; no featwell
Tor | standar service cone raoftank wth pan no
awe
frax |Moderate service cone rat tank
51 _|eeertace service cone rot tank 15-min. 5.
erential
152 imertace service cone rf tank 25 mins
rentis
‘Aluminum Gaugeead with loa rank
Tank Type
Hor | standard serve cone oof tank
70s | standard service bates take
30
[Rascoar- | [connie roa cert
tron Gaugehead (ATEX Approved)
30 [tank Type
j122 | Severe service cone rot tank S325,
1123. | extreme service cone root tank carp 20
}r24_ | sovere servic tank top mounting
(Rasoms=—| [eon rome cegiato
‘Aluminum Gaugehead with Negator Cassette
30 [tank Type
frox | Standard service cane rot tank
Hro2 | standard service cone roof tank with pan &
}703 | standard service eating root tank
vet
roa | Standard service tank top mounting
Hros | standard service bolted tank
th loa
1705. |stansard service eating roo! tank; no fatwel
}ro7 | standard service cone roof tank & pa; no feat
vet
raz | Moderate service cone roof tak
755. | suing wetlservic cone root tank
Metric Configuration
‘Aluminum Gaugehead with Negator Motor
10 Tank Type
frit | tondard serve cone roof tank
fri2 standard service cone oof ank with pan & lst
we
113 | standard service Roting oof tank wth flatwall
ria | standard service tank top mounting
ris | standard service bolted tank
ris. standard service fating roof tank no leatwall
Hru7 | tandara service cone oof tank wth pan; na
awa
fra2 | moderate service cone rot tank
rsa |inertace service cone roof tank; 25min. dt.
ret
1755. |stting wall serve cone oof tank "da. feat
ae
‘Aluminum Gaugehead with Float Crank
Tank Type
fan. [Standard seve cone root ane
a
i 3
lon Gaugehead (ATEX Approved)
0 Tank Type
31 |evere servic cone root tank
132 | severe service ane top mounting
133. Jestreme sence cone roof tank: morel
134 |estreme service cone rof tank car.20
‘Aluminum Gaugehead with Negator Cassette
0 Tonk Type
rir [standard serviee cone root tank
112 | standard service cone roo tank with pan
oaswe
113 | standard service Noting oof tank & oatwll
ria | standard service tank top mounting
H116 standard service floating roof tank: no toate
[117 _| standard service cone rf tank & panne ea
wel
jr42 [Moderate service cone rot tank
156 siting wel service cone roo tank
16
‘ares ne.Automatic Tank Gauge
2520 ATG Order Codes
150 PSI (10.3 Bar) Gage Steel Gaugehead
30
30
220 PSI (15 Bar) Gage Stee! Gaugehead
Measurement Unit
ot [Enasn
Jo2 | verre
Tank Type
fo | 26% ameter or sphere or cylinger Tanks
02 | 48 fe Damere or sphere or cylinder Tanks
03 |Top Mounting on sphere o ender Tanks
08 | 60% Oameser or sphere or cylinder Tanks
Plug vate
0 Pug vaivenotusea
1 |" (38m) 150 5: (20:3 Bar) Gage Plug
ave (itn A pl)
Transmitter Adapter
et denraton
Measurement Units
Tank ¥
05 | 161. Oameter or sphere or cylinder Tanks
06 | 481 oameter or sphere or eyinger Tans
107 | Top Mounting on sphere or einer Tanks
708 | 601 ameter or phere or eyinger Tas
Plug Vale
Jo. Pug ave not usee
| 2 a8 mm) 220° (2583 Gage Pug
valve (ton =A lg)
Transmiter Adapter
Note! 150(10.3 Bar) and 220 I (15 Bar) Gage version conforms to
[ATEX, Class Zone 2 (Ex 1126 15)
300 PSI (20.6 Bar) Gage Steel Gaugehead
»
Measurement Units
or
Foetsh
Tank Type
Fos | 16. Diameter or sphere or elinderTerks
70s | 48 Diameter orsahere orclinderTenks
707 J Toe Mounting on sphere or cinder Tanks
Tos | 0. Diameter or sphere or cylinder Tenks
Plug Valve
Jo [Plug vate not used
1 | 29 38.) 3000S (20.8837 Gage Pug
valve (Viton Ape)
Transiter Adapter
Jo | ransmitte Adapter Not Use
Technical information
v2500/2520 Automatic Tank Gauge
2500 ATG Product Dimensions
te ]
re ATG Product Dimensions