Professional Documents
Culture Documents
Footing
Footing
Program Description:
"FOOTINGS" is a spreadsheet program written in MS-Excel for the purpose of analysis of rigid rectangular
spread footings with up to 8 total piers, and for either uniaxial or biaxial resultant eccentricities. Overturning
sliding, and uplift stability checks are made when applicable, and resulting gross soil bearing pressures at
the four (4) corners of the footing are calculated. The maximum net soil bearing pressure is also determined.
This program is a workbook consisting of five (5) worksheets, described as follows:
Worksheet Name
Description
Doc
Footing (net pier loads)
Footing (breakdown of loads)
Footings (Table)
Footings (Pier Table)
9. The "Footing (breakdown of loads)" worksheet allows for individual breakdown of dead, live, and wind (or
seismic) loadings.
"FOOTINGS.xls" Program
Version 2.8
Job Name:
Job Number:
Input Data:
+Pz
Footing Data:
+My
+Hx
Footing Length, L =
Footing Width, B =
Footing Thickness, T =
Concrete Unit Wt., c =
Soil Depth, D =
Soil Unit Wt., s =
Pass. Press. Coef., Kp =
Coef. of Base Friction, =
Uniform Surcharge, Q =
8.000
5.000
2.000
0.150
2.000
0.120
3.000
0.400
0.200
ft.
ft.
ft.
Lpx
kcf
ft.
kcf
ksf
Pier/Loading Data:
Number of Piers =
Xp (ft.) =
Yp (ft.) =
Lpx (ft.) =
Lpy (ft.) =
h (ft.) =
Pz (k) =
Hx (k) =
Hy (k) =
Mx (ft-k) =
My (ft-k) =
Nomenclature
Pier #1
0.000
0.000
2.000
2.000
3.000
-80.00
20.00
0.00
0.00
0.00
Y
###
###
###
###
###
###
###
W(total) =
Pier Weigh
Pier #1
D
h
xp =
yp =
Pier Wt. =
T
-(Pz) =
(-Pz) =
Pz(dn) =
Pz(dn) =
Pz(up) =
Pz(up) =
Mex(due to Pz) =
Mex =
Mox(due to Hy & Mx) =
Mox(due to Pz) =
Mox =
Mey(due to Pz) =
Mey =
Moy(due to Hx & My) =
Moy(due to Pz) =
Moy =
Mrx =
Mrx =
Mry =
Mry =
Checker:
Pz =
ex =
ey =
FOOTING PLAN
5 of 10
Mrx =
Mox =
FS(ot)x =
Mry =
Moy =
FS(ot)y =
Pass(x) =
Frict(x) =
FS(slid)x =
Pass(y) =
Frict(y) =
04/01/2016 17:46:29
"FOOTINGS.xls" Program
Version 2.8
FS(slid)y =
Results:
Total Resultant Load and Eccentricities:
Pz = -110.44 kips
ex =
0.906
ft. (<= L/6)
ey =
0.000
Overturning Check:
Mrx =
N.A.
Mox =
N.A.
FS(ot)x =
N.A.
Mry = 409.76
Moy = 100.00
FS(ot)y =
4.098
Sliding Check:
Pass(x) =
Frict(x) =
FS(slid)x =
Passive(y) =
Frict(y) =
FS(slid)y =
Uplift Check:
Pz(down) =
Pz(uplift) =
FS(uplift) =
ft-kips
ft-kips
Line of zero
pressure
ft-kips
Pz(down) =
Pz(uplift) =
FS(uplift) =
Brg. Lx
P3 =
P4 =
Brg. Lx =
Brg. Ly =
Dist. y
% Brg. Area =
ft-kips
(>= 1.5)
-102.44
0.00
N.A.
Dist. x
kips
Pmax
kips
(>= 1.5)
Brg. Ly1
kips
Dist. y
Brg. Ly2
kips
Line of zero
pressure
kips
kips
Dist. x
Brg. Lx2
Pmax
Dist. y
Line of zero
pressure
Brg. Lx1
P3=0.886 ksf
P2=4.636 ksf
Brg. Lx
Pmax
B
P4=0.886 ksf
P(max) =
P(min) =
P3 =
P4 =
Brg. Lx =
Brg. Ly =
% Brg. Area =
P1=4.636 ksf
CORNER PRESSURES
Dist. y
Brg. Ly
P(max) =
P(min) =
P3 =
P4 =
Brg. Lx =
Brg. Ly =
% Brg. Area =
Check Ecc.:
P3 =
P4 =
Brg. Lx =
Brg. Ly =
% Brg. Area =
heck Ecc.:
P3 =
P4 =
Distance dx =
Distance dy =
Brg. Lx =
Brg. Ly =
% Brg. Area =
xial Case =
Brg. Lx =
Brg. Ly =
rg. Area =
Brg. Ly1 =
Brg. Ly2 =
% Brg. Area =
6 of 10
04/01/2016 17:46:29
"FOOTINGS.xls" Program
Version 2.8
Job Name:
Job Number:
Input Data:
+Pz
Footing Data:
+My
+Hx
Footing Length, L =
Footing Width, B =
Footing Thickness, T =
Concrete Unit Wt., c =
Soil Depth, D =
Soil Unit Wt., s =
Pass. Press. Coef., Kp =
Coef. of Base Friction, =
Uniform Surcharge, Q =
16.000
10.000
3.000
0.150
2.000
0.120
3.000
0.400
0.200
ft.
ft.
ft.
Lpx
kcf
ft.
kcf
ksf
Pier/Loading Data:
Number of Piers =
Xp (ft.) =
Yp (ft.) =
Lpx (ft.) =
Lpy (ft.) =
h (ft.) =
Pz(D) (k) =
Pz(L) (k) =
Pz(W) (k) =
Hx(D) (k) =
Hx(L) (k) =
Hx(W) (k) =
Hy(D) (k) =
Hy(L) (k) =
Hy(W) (k) =
Mx(D) (ft-k) =
Mx(L) (ft-k) =
Mx(W) (ft-k) =
My(D) (ft-k) =
My(L) (ft-k) =
My(W) (ft-k) =
Pier #1
-3.000
0.000
2.500
2.000
3.000
-5.00
-5.00
40.00
0.00
0.00
20.00
0.00
0.00
10.00
0.00
0.00
-10.00
0.00
0.00
10.00
Nomenclature
Pier #2
3.000
0.000
2.500
2.000
3.000
-30.00
-10.00
-40.00
0.00
0.00
10.00
0.00
0.00
0.00
0.00
0.00
-10.00
0.00
0.00
20.00
Y
FOOTING PLAN
7 of 10
###
###
###
###
###
###
###
W(total) =
Pier Weights and Lo
Pier #1
D
h
xp =
yp =
Pier Wt. =
T
-Pz =
(-Pz) =
Total Vertical Load:
Pz =
Eccentricity of Resul
Mx(due to Pz) =
Mx(due to HyD & MxD) =
L & MxL) =
Mx(due to HyW & MxW) =
Mx =
My(due to Pz) =
My(due to HxD, & MyD) =
My(due to HxL & MyL) =
My(due HxW & MyW) =
My =
ex =
ey =
Overturning Check:
Mrx(Wf+Ws) =
Mrx(PzD) =
Mrx(HyD) =
Mrx(MxD) =
Mrx =
Mox(PzW) =
Mox(HyW) =
Mox(MxW) =
Mox =
FS(ot)x =
Mry(Wf+Ws) =
Mry(PzD) =
Mry(HxD) =
Mry(MyD) =
Mry =
Moy(PzW) =
Moy(HxW) =
Moy(MyW) =
Moy =
FS(ot)y =
Sliding Check:
Hx(D) =
Hx(D)Resist =
Pass(x) =
Frict(x) =
Hx(W) =
Checker:
04/01/2016 17:46:29
"FOOTINGS.xls" Program
Version 2.8
FS(slid)x =
Hy(D) =
Hy(D)Resist =
Pass(y) =
Frict(y) =
Hy(W) =
FS(slid)y =
Results:
Total Resultant Load and Eccentricities:
Pz = -194.50 kips
ex =
2.776
ft. (> L/6)
ey =
0.411
ft. (<= B/6)
Overturning Check:
Mrx = 737.50
Mox = -80.00
FS(ot)x =
9.219
Mry = 1105.00
Moy = 450.00
FS(ot)y =
2.456
Sliding Check:
Hx(D)Resist =
Pass(x) =
Frict(x) =
FS(slid)x =
Hy(D)Resist =
Pass(y) =
Frict(y) =
FS(slid)y =
Uplift Check:
Pz(down) =
Pz(uplift) =
FS(uplift) =
0.00
-37.80
-65.00
3.427
0.00
-60.48
-65.00
12.548
Pmax
Brg. Ly
ft-kips
ft-kips
(>= 1.5)
ft-kips
ft-kips
Dist. y
Line of zero
pressure
(>= 1.5)
Brg. Lx
kips
kips
kips
(>= 1.5)
Dist. x
kips
Pmax
kips
kips
Brg. Ly1
(>= 1.5)
Dist. y
Brg. Ly2
-187.50
40.00
4.688
kips
Line of zero
pressure
kips
(>= 1.5)
P3=0.24 ksf
P2=2.804 ksf
Brg. Lx1
B
L
Brg. Lx
P1=2.179 ksf
CORNER PRESSURES
Pmax
Dist. y
Line of zero
pressure
Dist. x
P4=0 ksf
z(D) (dn) =
Pz(W) (dn) =
Pz(dn) =
Pz(up) =
Pz(up) =
Pz(down) =
Pz(uplift) =
FS(uplift) =
P3 =
P4 =
Brg. Lx =
Brg. Ly =
rg. Area =
P(max) =
P(min) =
P3 =
P4 =
Brg. Lx =
Brg. Ly =
% Brg. Area =
P(max) =
P(min) =
P3 =
P4 =
Brg. Lx =
Brg. Ly =
% Brg. Area =
heck Ecc.:
P3 =
P4 =
Brg. Lx =
Brg. Ly =
% Brg. Area =
Check Ecc.:
P3 =
P4 =
Pmax
Distance dx =
Distance dy =
Brg. Lx =
Dist. y
Brg. Ly =
Brg. Ly
% Brg. Area =
Biaxial Case =
Brg. Lx =
Brg. Ly =
% Brg. Area =
8 of 10
04/01/2016 17:46:29
"FOOTINGS.xls" Program
Version 2.8
Subject:
Originator:
Checker:
+Pz
Input Data:
+Y
Allow. Net Soil Pressure, Pa(net) =
Soil Unit Weight, s =
Passive Pressure Coefficient, Kp =
Coefficient of Base Friction, =
Concrete Unit Weight, c =
Conc. Compressive Strength, f'c =
Reinforcing Yield Strength, fy =
USD Load Fact. for Concrete, LF =
Design for P(max)net or Pa(net) ?
3.000
0.120
3.000
0.400
0.150
3
60
1.6
P(max)
ksf
+My
kcf
+Hx
L/2
ksi
+X
Lpy
B
T
ksi
Lpx
B/2
Footing Plan
COLUMN
LOCATION
A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-11
A-12
Axial
Pz
Lpx
kcf
COLUMN LOADS
Case 1: Maximum Load Condition
Shear
Shear
Moment Moment
Axial
Hx
Hy
Mx
My
Pz
Footing Elevation
Assumptions: 1. For uniaxial eccentricity (either ex or ey) the maximum gross soil pressure is calculated as follows:
for ex <= L/6: P(max)gross = ( Pz)/(B*L)*(1+6*ABS(ex)/L) and P(min)gross = ( Pz)/(B*L)*(1-6*ABS(ex)/L) , for ex > L/6: P(max)gross = (2* Pz)/(3*B*(L/2-ABS(ex))) and P(min)gross = 0
for ey <= B/6: P(max)gross = ( Pz)/(L*B)*(1+6*ABS(ey)/B) and P(min)gross = ( Pz)/(L*B)*(1-6*ABS(ey)/B) , for ey > B/6: P(max)gross = (2* Pz)/(3*L*(B/2-ABS(ey))) and P(min)gross = 0
where: Pz = summation of vertical load and all weights = applied column vertical load (Pz) + soil weight + excess pier weight + surcharge (Q).
2. Concurrent biaxial eccentricities (both ex and ey) are permitted up to point where full contact (100% bearing) on the footing base is still maintained.
P(max)gross = ( Pz)/(B*L)*(1+6*ABS(ex)/L+6*ABS(ey)/B) and P(min)gross = ( Pz)/(B*L)*(1-6*ABS(ex)/L-6*ABS(ey)/B)
where: controlling biaxial eccentricity criteria is as follows: 6*ABS(ex)/L+6*ABS(ey)/B <= 1.0
3. Maximum net soil pressure is calculated as follows: P(max)net = P(max)gross-(D+T)* s >= 0
4. Program considers all applied moments and horizontal loads as forces causing overturning. However, uplift load (Pz > 0) is considered as a force causing overturning only when there is an applicable
resultant eccentricity in the direction of overturning. Combination of frictional resistance between footing base and soil as well as passive soil pressure against footing base and pier is used for total
sliding resistance.
5. Program includes uniform live load surcharge (Q) in calculation of soil bearing pressures, and is assumed to act over entire footing plan area (L*B). Uniform live load surcharge (Q) is not included in any
of stability checks.
6. One-way and two-way shear capacity checks are based on full uniform design net bearing pressure, P(net) = either P(max)net or Pa(net), as selected by user.
7. Footing flexural reinforcing for bottom face is based on full uniform design net bearing pressure, P(net) = either P(max)net or Pa(net), as selected by user. Footing flexural reinforcing for top face
is determined only when there is an applied column uplift load (Pz > 0), and is based on bending from footing self-weight plus any soil and live load surcharge (Q) weight.
8. Minimum temperature reinforcing is determined as follows: As(temp) = (temp)*12*T (all reinforcing placed in bottom face only) for no column uplift and with soil cover (D > 0)
As(temp) = (temp)/2*12*T (reinforcing divided equally between top/bottom faces) for either with column uplift and/or no soil cover (D = 0)
where: (temp) = 0.0020 for fy = 40 or 50 ksi, (temp) = 0.0018 for fy = 60 ksi, and (temp) = 0.0018*60/fy for fy > 60 ksi.
9. For rectangular footings, the reinforcing in the short direction is calculated by: As(short) = 2/( +1)*As(long) , where = ratio of long side to short side.
FOOTING DATA
Pier Dimensions
Base Dimensions
Length
Width
Height
Length
Width
Thickness
Lpx
Lpy
h
L
B
T
SOIL DATA
& SURCHARGE
Depth
Surch.
D
Q
Bearing Pressures
P(max)
P(max)
(gross)
(net)
Stability Checks
F.S.
F.S.
Sliding
Sliding
Overturning Overturning
F.S.
F.S.
(kips)
(kips)
(kips)
(ft-kips)
(ft-kips)
(kips)
(kips)
(kips)
(ft-kips)
(ft-kips)
(ft.)
(ft.)
(ft.)
(ft.)
(ft.)
(ft.)
(ft.)
(ksf)
(ksf)
(ksf)
X-axis
Y-axis
X-direction
Y-direction
-200.00
-200.00
-200.00
-200.00
-200.00
-200.00
-200.00
-200.00
10.00
-10.00
0.00
0.00
10.00
-10.00
0.00
0.00
0.00
0.00
10.00
-10.00
0.00
0.00
10.00
-10.00
0.00
0.00
-40.00
40.00
0.00
0.00
-40.00
40.00
40.00
-40.00
0.00
0.00
40.00
-40.00
0.00
0.00
-20.00
-20.00
-20.00
-20.00
10.00
-10.00
0.00
0.00
0.00
0.00
10.00
-10.00
0.00
0.00
-40.00
40.00
40.00
-40.00
0.00
0.00
-20.00
-20.00
-20.00
-20.00
10.00
-10.00
0.00
0.00
0.00
0.00
10.00
-10.00
0.00
0.00
-40.00
40.00
40.00
-40.00
0.00
0.00
3.000
3.000
2.000
2.000
3.000
3.000
2.000
2.000
3.000
3.000
2.000
2.000
2.000
2.000
3.000
3.000
2.000
2.000
3.000
3.000
2.000
2.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
12.000
12.000
8.000
8.000
12.000
12.000
8.000
8.000
12.000
12.000
8.000
8.000
8.000
8.000
12.000
12.000
8.000
8.000
12.000
12.000
8.000
8.000
12.000
12.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
0.200
0.200
0.200
0.200
0.200
0.200
0.200
0.200
0.200
0.200
0.200
0.200
3.305
3.305
3.305
3.305
3.305
3.305
3.305
3.305
1.430
1.430
1.430
1.430
2.825
2.825
2.825
2.825
2.825
2.825
2.825
2.825
0.950
0.950
0.950
0.950
----4.87
4.87
----16.87
16.87
----4.87
4.87
4.87
4.87
----16.87
16.87
----4.87
4.87
-----
4.94
4.94
----12.14
12.14
----4.94
4.94
-----
----4.94
4.94
----12.14
12.14
----4.94
4.94
9 of 10
F.S.
Uplift
-------------------------
RESULTS
Shear Capacity Checks
One-Way One-Way Two-Way
Vu/Vc
Vu/Vc
Vu/Vc
X-direction
Y-direction
0.57
0.57
0.30
0.30
0.57
0.57
0.30
0.30
0.19
0.19
0.10
0.10
0.30
0.30
0.57
0.57
0.30
0.30
0.57
0.57
0.10
0.10
0.19
0.19
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.17
0.17
0.17
0.17
Footing Reinforcing
Bottom Face
Top Face
X-direction
Y-direction
X-direction
Y-direction
(in.^2/ft.)
(No. - Size)
(in.^2/ft.)
(No. - Size)
(in.^2/ft.)
(No. - Size)
(in.^2/ft.)
(No. - Size)
0.522
0.522
0.518
0.518
0.522
0.522
0.518
0.518
0.518
0.518
0.518
0.518
9 - #7
9 - #7
13 - #7
13 - #7
9 - #7
9 - #7
13 - #7
13 - #7
9 - #7
9 - #7
13 - #7
13 - #7
0.518
0.518
0.522
0.522
0.518
0.518
0.522
0.522
0.518
0.518
0.518
0.518
13 - #7
13 - #7
9 - #7
9 - #7
13 - #7
13 - #7
9 - #7
9 - #7
13 - #7
13 - #7
9 - #7
9 - #7
-------------------------
-------------------------
-------------------------
-------------------------
04/01/2016 17:46:29
"FOOTINGS.xls" Program
Version 2.8
Subject:
Originator:
Checker:
+Pz
Lpx
Input Data:
+Y
Concrete Unit Weight, c =
Conc. Compressive Strength, f'c =
Reinforcing Yield Strength, fy =
USD Load Fact. for Concrete, LF =
Clear Cover to Pier Ties, dc =
0.150
3
60
1.6
2.000
+Hx
Q
ksi
L/2
ksi
D
in.
Lpy
8.
Footing Plan
A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-11
A-12
Ntb
(total)
B/2
COLUMN LOADS
Case 1: Maximum Load Condition
Shear
Shear
Moment Moment
Axial
Hx
Hy
Mx
My
Pz
Nsb
(total)
B
Ldh
6.
7.
+X
Lpx
Axial
Pz
d' (typ.)
+My
kcf
Lpy
COLUMN
LOCATION
Program uses CRSI's "Universal Column Formulas" in developing uniaxial interaction curves for X and Y axes, each load case.
CRSI's "Universal Column Formulas" assume use of fy = 60 ksi.
Program assumes "short", non-slender column analysis for pier.
For cases with axial load only (compression or tension) and no moments (Mx and My = 0) the program calculates total
reinforcing area (Ast) as follows:
Ast = (Ntb + Nsb)*Ab , where: Ab = area of one bar
5. For pure moment capacity with no axial load, program assumes bars in 2 outside faces parallel to axis of bending plus 50%
Footing Elevation
Pier Section
9.
FOOTING DATA
PIER REINFORCING DATA
Pier Dimensions
Base Dimensions
Top/Bot.
Side
Vert.
Horiz. Tie Horiz. Tie
Reinf.
Length
Width
Height
Length
Width
Thickness Vert. Bars Vert. Bars Bar Size Bar Size Bar Spac.
Ratio
g=Ast/Ag
Lpx
Lpy
h
L
B
T
Ntb
Nsb
(#3 - #11) (#3 - #6)
S
(kips)
(kips)
(kips)
(ft-kips)
(ft-kips)
(kips)
(kips)
(kips)
(ft-kips)
(ft-kips)
(ft.)
(ft.)
(ft.)
(ft.)
(ft.)
(ft.)
-200.00
-200.00
-200.00
-200.00
-200.00
-200.00
-200.00
-200.00
10.00
-10.00
0.00
0.00
10.00
-10.00
0.00
0.00
0.00
0.00
10.00
-10.00
0.00
0.00
10.00
-10.00
0.00
0.00
-40.00
40.00
0.00
0.00
-40.00
40.00
40.00
-40.00
0.00
0.00
40.00
-40.00
0.00
0.00
-20.00
-20.00
-20.00
-20.00
10.00
-10.00
0.00
0.00
0.00
0.00
10.00
-10.00
0.00
0.00
-40.00
40.00
40.00
-40.00
0.00
0.00
-20.00
-20.00
-20.00
-20.00
10.00
-10.00
0.00
0.00
0.00
0.00
10.00
-10.00
0.00
0.00
-40.00
40.00
40.00
-40.00
0.00
0.00
3.000
3.000
2.000
2.000
3.000
3.000
2.000
2.000
3.000
3.000
2.000
2.000
2.000
2.000
3.000
3.000
2.000
2.000
3.000
3.000
2.000
2.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
12.000
12.000
8.000
8.000
12.000
12.000
8.000
8.000
12.000
12.000
8.000
8.000
8.000
8.000
12.000
12.000
8.000
8.000
12.000
12.000
8.000
8.000
12.000
12.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
of the total side bars divided equally by and added to the 2 outside faces, and calculated reinforcing areas as follows:
for X-axis: As = A's = ((Ntb + 0.50*Nsb)*Ab)/2 , where: Ab = area of one bar
for Y-axis: As = A's = (((Nsb+4) + 0.50*(Ntb-4))*Ab)/2
Reinforcing ratio shown is as follows: g = (Ntb + Nsb)*Ab/(Lpx*12*Lpy*12).
Axial load and flexural uniaxial design capacities, Pn and Mn, at design eccentricity, e = Mu*12/Pu, are determined from
interpolation within the interaction curve for each axis.
Axial load and flexural biaxial capacities, if applicable, are determined by the following approximations:
a. For Pu >= 0.1*f'c*Ag, use Bresler Reciprocal Load Equation:
1/Pn = 1/Pnx + 1/Pny - 1/Po
Biaxial interaction stress ratio, S.R. = Pu/Pn <= 1
b. For Pu < 0.1*f'c*Ag, use Bresler Load Contour interaction equation:
Biaxial interaction stress ratio, S.R. = (Mux/Mnx)^1.15 + (Muy/Mny)^1.15 <= 1
Straight-line interaction formula is used for biaxial shear interaction stress ratio, S.R. = Vux/Vnx + Vuy/Vny <= 1
RESULTS
Case 2: Axial and Flexural Capacity Checks
X-axis
Y-axis
Biaxial
Pu/Pnx Mux/Mnx Pu/Pny
Muy/Mny
S.R.
X-direction Y-direction
Vu/Vnx
Bearing
Check
Pu/Pnb
(in.)
10
10
10
10
10
10
10
10
10
10
10
10
6
6
6
6
6
6
6
6
6
6
6
6
10 of 10
6
6
6
6
6
6
6
6
6
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
12
12
12
12
12
12
12
12
12
12
12
12
0.008
0.008
0.008
0.008
0.008
0.008
0.008
0.008
0.008
0.008
0.008
0.008
0.22
0.22
0.23
0.23
0.22
0.22
0.23
0.23
---------
----0.23
0.23
----0.23
0.23
---------
0.23
0.23
0.22
0.22
0.23
0.23
0.22
0.22
---------
0.23
0.23
----0.23
0.23
-------------
-------------------------
0.02
0.02
0.25
0.25
--------0.02
0.02
0.25
0.25
----0.25
0.25
------------0.25
0.25
0.25
0.25
0.02
0.02
--------0.25
0.25
0.02
0.02
0.25
0.25
------------0.25
0.25
-----
-------------------------
0.12
0.12
----0.11
0.11
----0.12
0.12
-----
----0.12
0.12
----0.11
0.11
----0.12
0.12
-------------------------
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.01
0.01
0.01
0.01
04/01/2016 17:46:29