Professional Documents
Culture Documents
SANYO Error Codes
SANYO Error Codes
SANYO Error Codes
A CODES
GHP ENGINE ISSUES
Code Description
A01
A02
A03
A04
A05
A06
A07
A08
A09
A10
A11
A12
A13
A14
A15
A16
A17
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
C CODES
CENTRAL CONTROLLER ISSUES
Code Description
C01
C02
C03
C04
C05
C06
C12
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
C26
C28
C29
C31
E CODES
ADDRESSING & COMMUNICATION PROBLEMS
Code Description
E01
E02
E03
E04
E05
E06
E07
E08
E09
E10
E11
E12
E13
E14
E15
E16
E17
E18
E20
E24
E25
E26
E29
E31
Remote control detecting error from indoor unit, Address not set/Auto address failed. Check interconnecting wiring etc. Re-address system.
Remote detecting error from indoor unit,
Indoor unit detecting error from remote,
Indoor seeing error from outdoor. Qty of i/d units connected are less than qty set. Check; all i/d units are ON,
reset turn off all units wait 5min power up
Indoor unit detecting error from outdoor unit, Error in sending comms signal
Outdoor unit detecting error from indoor unit, Error in receiving comms signal
Outdoor unit detecting error from indoor unit, Error in sending comms signal
Incorrect setting indoor/controller, Indoor address duplicated
Incorrect setting indoor/controller, Remote address duplicated or IR wireless controller not disabled
Indoor unit detecting error from 'option' plug, Error in sending comms signal
Indoor unit detecting error from 'option' plug, Error in receiving comms signal
Auto addressing failed, Auto address connector CN100 shorted during auto addressing
Indoor unit failed to send signal to remote controller
Setting Failure, Duplication of master indoor units
Auto addressing failed, Number of indoor units connected are less than number set
Auto addressing failed, Number of indoor units connected are more than number set
Group control wiring error, Main indoor unit not sending signal for sub indoor units
Group control wiring error, Main indoor unit not receiving signal for sub indoor units
Auto addressing failed, No indoor units connected
Auto addressing failed, Error on sub outdoor unit
Auto addressing failed, Error on outdoor unit address setting
Auto addressing failed, Quantity of main and sub outdoor units do not correspond to the number set on main
outdoor unit P.C.B.
Auto addressing failed, Sub outdoor unit not receiving comms for main outdoor unit
Between units, Comms failure with MDC, does E31 remain after power is re instated? If so replace PCB. & power
PCB
F & H CODES
SENSOR FAULTS
Code Description
F01
F02
F03
F04
F05
F06
F07
F08
F10
F11
F12
F13
F16
F17
F18
F20
F23
F24
F29
F30
F31
COMPRESSOR ISSUES
Code Description
H01
H02
H03
H05
H06
H07
H08
H11
H12
H13
H15
H27
H28
H31
L CODES
INCORRECT SETTINGS
Code Description
L01
L02
L03
L04
L05
L06
L07
L08
L09
L10
L11
L13
L15
L16
L17
L18
L19
L21
P CODES
Code Description
P01
P02
P03
P04
P05
P09
P10
P11
P12
P14
P15
P16
P17
P18
P19
P20
P22
P26
P29
P30
P31
Indicates conformation
with EC Directives
SANYO reserves the right to make any variation in specification to the equipment described or to withdraw or replace products
without prior notification or public announcement. All descriptions, illustrations, drawings and specifications in this publication
are given in good faith, but are intended to present only general particulars and shall not form any part of the contract. For full
installation details, please contact your SANYO distributor.
Rating Conditions
The cooling and heating capacities are based on the following conditions:
Cooling: Indoor temperature 27C DB/19C WB, Outdoor temperature 35C DB/24 C WB.
Heating: Indoor temperature 20C DB, Outdoor Temperature 7C DB 6C WB.
Printed using paper produced from 50% recycled material and 50% from sustainable forestry.
www.sanyoaircon.com
SANYO Air Conditioners. The natural choice.