niversity
School of Engineering & Technology
Capstone Power and Control Design
Week 6 Tutorial
Question 1
‘A.10 MVA load is installed and couples to a MV bus where the fault level is 1OOOMVA.
(a] Would this load pass a stage 1 flicker assessment?
(b) Using the planning levels given in lectures for MV systems compute the short and
long term MV globally allowable flicker levels assuming a HV->MV transmission
coefficient of 0.7.
(c) Assuming coincidence factors of 0.3 determine the maximum allowable short
and long term flicker levels for this load.
(4) Repeat (c) for a 50 MVA load.
(e) With both the 5 MVA and the 50 MVA loads connected compute the allowable
flicker available for subsequently connected loads ( note the cubic summation
law)
(f) Compute the maximum load for part (e) that could be connected without failing
a stage 2 assessment.
Question 2
(a) Using Excel compute the MV global contribution for all harmonics up to 25 assuming
a transmission coefficient from HV to MV of 1.0
(b) Using this information compute the harmonic emission limits for 750 kVa MV load
fed from HV via a 40 MVA transformerQuestion 3
A salient pole generator with a parameters given on the next page has a EXACA type exciter
and a TGOV1 governor installed. It is connected to an infinite bus via a transformer and line
each with 5% reactances. Assume the generator supplies 1 per unit power to the infinite
bus.
(a) Construct this system in PSSE and perform a load flow.
(b) Construct the dyr file and simulate a bolted three phase fault on the HV side of the
transformer.
{c) Repeat (b) with the exciter disabled
(d) Repeat (b) with the governor disabled
(c) Determine the critical clearing time
(f) Perform an exciter response test for this system
(g) Perform a governor response test for this systemSIEMENS
Generator Model Data Sheets Psst 33.5
GENSAE PSS®E Model Library
ee een eens
1.20 GENSAE
Salient Pole Generator Model (Exponential Saturation on Both Axes)
‘This model is located at system
hone #____ Bus,
\ # :
a as rd
an 4 my LISORCE, sours Curent
and STATES starting with Vr POETS) GENSAE | ETERM terminal Voltage
‘The See is. foreach of Bus
ZSORCE for this machine is +] ANGLES angle
‘on the above MBASE,
CoNe | # | Value Deserintion
J Tao (#0) (sec)
Jet OO LT "do (70) (sec)
Try 0:0. 21] 7" O) (sec)
He (-0 |Finenia
ie @-0 |D, Speed damping
a6 2.25%
i 1-47 [a
7 0.21%
a8 O16 |Re=*a if
#9 Pa
J#10 Ot {80.0
it 0:6 (S02)
Note: Xq, Xq, X's, X°d, X"q, Xi, H, and D are in pu, machine MVA base.
X’q must be equal to X"g.
‘SiaTes [| # Description
K Ey
KH va
Kee vkd
KS A speed (pu)
Kea ‘Angie (radians) a
IBUS, "GENSAE’, ID, CON() to CONW#11)
‘All material contained inthis documentation i proprietary to Siemens industy, ne. Siemens Power Technologies Inernational
1468SIEMENS
pss 33.5 ‘Turbine-Governor Model Data Sheets
PSS®E Model Library TGOVI
ee ea
7.21 TGOV1
Steam Turbine-Governor
This model s located at system bus # 1Bus,
Machine identifier “ 10, an oo
This model uses CONs starting with 4 SPEED | cov: | PMECH,
‘and STATES starting with « kK
‘and VAR * L
cons [_#_| Value Description
J O05 |R
v4 0-4 [1 9) (ee)
Be LS |viwax"
3 0.00 Monn
4 OY [Te (sec?
a 1-2 [ts 0) (sec)
m7 0-0 [oF
1” Vax. Van, Dt and Rare in per unit on generator MVA base.
; ‘T2lTg = high-pressure fraction,
reheate ime constant.
‘stares | # Description
K Valve opening
ie Turbine power
vars | # | Description
T [Reference
IBUS, ‘TGOV1’, ID, CON(J) to CON(#6) 1
Allmaterial contained inthis ocumenttion is proprietary to Siemens Industy, Inc, Siemens Power Technologies Intemational
7-61SIEMENS
‘Turbine-Governor Model Data Sheets pss 33.5
T6OVt PSS®E Model Library
PMECH
‘All material contained in this documentation is propristery to Siemens industry, Inc, Siemens Power Technologies International.
782SIEMENS
Excitation System Model Data Sheets pss®e 33.5
EXAC4 PSS®E Model Library
——
6.28 EXAC4
IEEE Type AC4 Excitation System
This model is located at system bus IBus,
Machine identifier +,
This model uses CONs starting with @ J, a
and STATEs starting with K. =
cons | # | Value Description
Z Gos [TR
a 10 _|Vimax
we =10 [Vim
Es 9-0000i|TC
4 0-00001 |Te (see)
#5 20 |Ka
6 0.02 [TA
#7 | [o_|vrmax
He =10 [VaMIN
8 oO [Ke
states | # Description
K Vmeasvres
a Lead lag
2 Ve
IBUS, 'EXACA’, ID, CON(J) to CON(J+8) /
VReF Vs
] _ viwax rau Koteo
|. + teste] [ka
5 |_|
o> Teste) ert *\ieste| *|Testal 7?
Vian VRMIN-Kc Heo
\VS= VOTHSG + VUEL + VOEL.
All material contained in this documentation is proprietary to Siemens Industry, In. Siemens Power Technologies international
6-86