Professional Documents
Culture Documents
KARBURATOR - Održavanje I Simptomi Zaprljanog Karburatora Održavanje I Simptomi Zaprljanog Karburatora
KARBURATOR - Održavanje I Simptomi Zaprljanog Karburatora Održavanje I Simptomi Zaprljanog Karburatora
Na slici je obeleena glavna dizna koju treba odvrnuti, oprati u benzinu i produvati kompresorom. Nakon ienja dizne vratiti je na mesto i zavrnuti olju.
Potom uzeti istu krpu, provui je kroz karburator i obrisati ga (kao i olju) ili ga produvati na kompresoru. Takav karburator smatra se oienim i spreman
cvele19
Group:Forum Manijak
Posts:4,852
Joined:08-January 08
Skuter:keewaj 70
Cilindar:s6 sport
Auspuh:s6 pro replica
Karburator:dell 19
Kvailo:MF evo
Variomat:malossi multivar
Ostalo:athena torque...ma svasta ponesto...
Garaa:nis
Trgovina:+4
Bicilindrico
I start by removing the 2 phillips scres that hold the auto-enrichener on.
Once it is off, I make sure everything can move freely and clean it off with a little carb cleaner. Carb cleaner harms some plastic so you may want to just get the metal parts with it
and wipe the rest.
I now remove the clamp and float bowl drain hose. Clean it off and be sure it is not cracked or torn. Replace if necessary.
Now I spray the carb with carb cleaner to get rid of a lot of the grease and gunk.
Remove the carb top. There is a gasket under it, inspect that and replace if it is damaged.
Now I take out the 4 screws holding the float bowl in place.
http://www.skuteri.o...ing-mog-kineza/
S6 sport
MF evo radilica
multivar+4.2g+bela centr.+T.C.
s6 pro replica
b9eg-more i bosna f95
dellorto phbg 19 black edition-w9,diz. 82-85....
minarelli CDI by Icatenej+ advace paljenje...
malossi primar 15/41
torque drive Athena
MF evo race +S6 w/c
http://i298.photobuc...ican-mojbok.jpg
http://i298.photobuc...rriDSC00334.jpg
cvele19
Group:Forum Manijak
Posts:4,852
Joined:08-January 08
Skuter:keewaj 70
Cilindar:s6 sport
Auspuh:s6 pro replica
Karburator:dell 19
Kvailo:MF evo
Variomat:malossi multivar
Ostalo:athena torque...ma svasta ponesto...
Garaa:nis
Trgovina:+4
Now I take out the 4 screws holding the float bowl in place.
Bicilindrico
My bowl has some buildup, so I spray some carb cleaner in the bowl and let it sit.
Remove the float bowl gasket and spray the carb out with carb cleaner.
http://www.skuteri.o...ing-mog-kineza/
S6 sport
MF evo radilica
multivar+4.2g+bela centr.+T.C.
s6 pro replica
b9eg-more i bosna f95
dellorto phbg 19 black edition-w9,diz. 82-85....
minarelli CDI by Icatenej+ advace paljenje...
malossi primar 15/41
torque drive Athena
MF evo race +S6 w/c
http://i298.photobuc...ican-mojbok.jpg
http://i298.photobuc...rriDSC00334.jpg
cvele19
Group:Forum Manijak
Posts:4,852
Joined:08-January 08
Skuter:keewaj 70
Cilindar:s6 sport
Auspuh:s6 pro replica
Karburator:dell 19
Kvailo:MF evo
Variomat:malossi multivar
Ostalo:athena torque...ma svasta ponesto...
Garaa:nis
Trgovina:+4
Remove the float bowl gasket and spray the carb out with carb cleaner.
Bicilindrico
I unscrewed the main jet to make sure it isn't clogged or dirty and sprayed it out. I then reinstalled it.
I then removed the idle speed screw and cleaned the screw and passage, then reinstalled. You may want to see how many turns it takes to get the idle screw all the way in, and
write that down. When reinstalling, turn the screw all the way in then back it out that number of turns.
Now I remove the clip that holds jet needle and it's clip in the throttle valve.
http://www.skuteri.o...ing-mog-kineza/
S6 sport
MF evo radilica
multivar+4.2g+bela centr.+T.C.
s6 pro replica
b9eg-more i bosna f95
dellorto phbg 19 black edition-w9,diz. 82-85....
minarelli CDI by Icatenej+ advace paljenje...
malossi primar 15/41
torque drive Athena
MF evo race +S6 w/c
http://i298.photobuc...ican-mojbok.jpg
http://i298.photobuc...rriDSC00334.jpg
cvele19
Group:Forum Manijak
Posts:4,852
Joined:08-January 08
Skuter:keewaj 70
Cilindar:s6 sport
Auspuh:s6 pro replica
Karburator:dell 19
Kvailo:MF evo
Variomat:malossi multivar
Ostalo:athena torque...ma svasta ponesto...
Garaa:nis
Trgovina:+4
remove the clip that holds jet needle and it's clip in the throttle valve.
Bicilindrico
Clean all of these parts then reassemble. Be sure the M clip doesn't block the groove in the throttle valve when you put it back together.
Now I let all of this sit overnight so the carb cleaner can work it's magic on the bowl.
The carb cleaner has done it's work so I dump it out and wipe the bowl out.
I remove the drain screw and clean it and the opening with carb cleaner, then reinstall the screw.
Put the bowl gasket back in place, making sure it is properly seated.
Reinstall the float and float needle. Now is a good time to check float height by measuring from the bottom of the carb to the bottom of the float (which are both kinda the tops
since it's held upside down). Vento wants a 12-14mm float height.
Now I put the throttle valve back in the carburetor. Notice there is a long groove and a small ramp on the throttle valve. The ramp is for your idle speed screw to contact, so aim
int toward the idle speed scew when installing.
Now I put the throttle valve back in the carburetor. Notice there is a long groove and a small ramp on the throttle valve. The ramp is for your idle speed screw to contact, so aim
int toward the idle speed scew when installing.
In my case, make sure the cap for the oil injection port is in good shape.