Professional Documents
Culture Documents
" " Series Variable Displacement Piston Pumps: 21 (3050) A10 A16 A22 A37 A56 A70 A90 A145 A220
" " Series Variable Displacement Piston Pumps: 21 (3050) A10 A16 A22 A37 A56 A70 A90 A145 A220
A37 A1637
A56
A16 A10
A10
21 (3050)
A16
A22 16 (2320)
A37
21 (3050)
Single Pumps A56 30
M
O A70
A90 28 (4060)
A145
A220 16 (2320)
Various control types are available such as pressure compensator type. Refer to page 31 and 32.
The maximum operating pressure for each double pump depends on its combination of pumps. Contact us for details.
27
Hydraulic Fluids
Hydraulic Fluids Control of Contamination
Use petroleum based oils such as anti-wear type hydraulic Due caution must be paid to maintaining control over
oils or R & O (Rust and Oxidation inhibitor) type hydraulic contamination of the operating oil which can otherwise
oils equivalent to ISO VG-32 or 46. The recommended lead to breakdowns and shorten the life of the unit.
viscosity range is from 20 to 400 mm2/s (98 to 1800 SSU) Please maintain the degree of contamination within NAS
and temperature range is from 0 to 60°C (32 to 140°F), Grade 10.
both of which have to be satisfied for the use of the above The suction port must be equipped with at least a 100 µm
hydraulic oils. (150 mesh) reservoir type filter and the return line must
have a line type filter of under 10 µm.
Instructions
Mounting Drain Piping
When installing the pump the filling port should be Install drain piping according to the chart and ensure that
positioned upwards. pressure within the pump housing should be maintained
at a normal pressure of less than 0.1 MPa (14.5 PSI) and
Alignment of Shaft surge pressure of less than 0.5 MPa (72.5 PSI).
Employ a flexible coupling whenever possible, and avoid Length of piping should be less than 1 m (3.3 ft.), and
any stress from bending or thrust. the pipe end should be submerged in oil.
Maximum permissible misalignment is less than 0.1 mm
(.004 inches) TIR and maximum permissible misangular [Recommended Drain Piping Size]
is less than 0.2°.
Fitting Size
Inside Dia.
Suction Pressure Model Japnese Std. "JIS" & N.American of Pipe
European Design Std. Design Std.
Permissible suction pressure at inlet port of the pump is
between -16.7 and +50 kPa (5 in.Hg Vacuum and 7 3/8 SAE #6
A10
PSIG). [Inside Dia. 8.5 mm (.33 in.) or more] 10 mm
For piping to the suction port, use the pipes of the same 3/8 SAE #8 (.39 in.)
diametre as that of the specified pipe flange to be used. A16, A22
[Inside Dia. 8.5 mm (.33 in.) or more]
Make sure that the height of the pump suction port is
1/2 SAE #10 12 mm
within one metre (3.3 ft) from the oil level in the reservoir. A37
[Inside Dia. 10 mm (.47 in.) or more] (.47 in.)
"A" Series
pump is returned direct to the reservoir or the actuator
moves in a free load. Adjustment of Discharge Pressure
Turning the adjustment screw clockwise, increases
[Volume of Pre-fill Oil Required] pressure.
Model Volume cm3 (cu.in.) Volume adjusted by each full turn of the pressure
A10 370 (22.6) adjustment screw
A16/A22 600 (36.6)
Adjustment Volume
A37/A56 1200 (73.2) Model Numbers
MPa (PSI)
A70 2100 (128) A10-FR01B 2.9 (420)
A90 2500 (153) A10-FR01C/H 5.4 (780)
A145 3300 (201) A16/A22/A37/A56-*-R-01-B 3.5 (510)
A16/A22/A37/A56-*-R-01-C 6.5 (940)
A16/A37/A56-*-R-01-H 7.9 (1150)
A70/A90/A145-*-R01B 2.3 (330)
A70/A90/A145-*-R01C 3.2 (460)
A70/A90/A145-*-R01H 4.0 (580)
A70/A90/A145-*-R01K 4.7 (680)
Adjustment of Delivery
Turning the flow adjustment screw clockwise, decreases
delivery.
Adjustable volume
Model with each full turn Minimum adjustment flow
of the adjustment
Numbers screw cm3/rev (cu.in./rev)
cm3/rev (cu.in./rev)
A10 1.1 (.067) 2.0 (.122)
A16 1.4 (.085) 4.0 (.244)
A22 2.0 (.122) 6.0 (.366)
A37 2.9 (.177) 10 (.610)
A56 3.9 (.238) 12 (.732)
A70 4.4 (.268) 30 (1.83)
A90 4.8 (.293) 56 (3.42)
A145 7.2 (.439) 83 (5.06)
Control Piston
Spool
Drain Port
Pivot
Flow Adj. Screw
Shaft
OUT
IN
Yoke
Features
High efficiency Low noise level
Under the conditions of pressure 16 MPa (2320 PSI) In the "A16" pump, the noise level is as low as 57.3
and speed 1800 r/min, the volumetric efficiency is over dB(A) [at the full cut-off pressure 21 MPa (3050 PSI)
98% and the overall efficiency is over 90%. with speed 1500 r/min one metre (3.3 ft.) horizontally
away from pump head cover.]
Output Flow
20
5
Noise Level
Efficiency
8 6 16 4 60
Input Power Full Cut-off
12 3
4 3 8 2 50
4 1
0 0
0 0 40
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3000 PSI 0 500 1000 1500 2000 2500 3000 PSI
Pressure Pressure
"A" Series
Output Flow
When the system pressure increases and comes close
Pressure
to the preset cut-off pressure, the pump flow decreases
"01" Compensator
automatically while maintaining the set pressure as it
33
M
Type
O is.
Pressure
Output Flow
Solenoid-two PL PH This type of control is ideal for an application where the
Pressure SOL SOL output power of the actuator has to be controlled in two
"02" Control "OFF" "ON" 55
different load pressures while keeping the actuator
Type speed nearly constant.
PL PH
M
O
Pressure
Electro-
minimum necessary level to operate the actuator.
Hydraulic
"04" Pump flow rate and cut-off pressure are controlled 64
Load
proportional to the input current to the control device
Sensing
M on the pump and the input current is regurated by the
Type O Pressure
(S Input Current i 1 L) specific amplifier.
Electro-
Hydraulic This type of control has the pressure sensor and tilt
Proportional angle sensor in the pump. The pump is used with the
"04E" Pressure & external amplifier (amplifier is integrated into pump 74
L)
Two-Pressure QH
Output Flow
SOL"OFF"
Two-Pressure QH
Output Flow
by Solenoid PH
changeover from rapid advance, to feed has been made.
Valve PL PH
M
O
Pressure
Output Flow
Pilot Pressure
Control Type control valve. By controlling the pilot
"07" Pressure pressure, the full cut-off pressure can be 96
Compensator
M
O
remote-controlled according to your
Pressure requirements.
Output Flow
Constant Input Power the preset input power.
"09" Power 105
Control Type The pump can act for function of two
M
pumps, low-pressure large-flow and
O
high-pressure small-flow. Therefore, the
Pressure motor capacity can be reduced.
Control type "05" and "06" are not shown in this catalogue. Contact us for the details.
"A" Series
Graphic Symbol
M
O
Specifications
Geometric Minimum Operating Presure Shaft Speed Range Approx. Mass
Displacement Adj. Flow MPa (PSI) r/min kg (lbs.)
Model Numbers
cm3/rev cm3/rev 2 1 Flange Foot
(cu. in. /rev) (cu. in. /rev) Rated Intermittent Max. Min.
Mtg. Mtg.
A10-FR01B-12* 5.1 (11.2)
10.0 (.610) 2 (.122) 16 (2320) 21 (3050) 1800 600
A10-FR01C/H-12* 8.5 (18.7)
A16-*-R-01-*-*-K-32* 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 1800 600 16.5 (36.4) 18.7 (41.2)
A22-*-R-01-*-*-K-32* 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 1800 600 16.5 (36.4) 18.7 (41.2)
A37-*-R-01-*-*-K-32* 36.9 (2.25) 10 (.610) 16 (2320) 21 (3050) 1800 600 28.0 (61.7) 32.3 (71.2)
A56-*-R-01-*-*-K-32* 56.2 (3.43) 12 (.732) 16 (2320) 21 (3050) 1800 600 35.0 (77.2) 39.3 (86.7)
A70-*R01*S-60* 70.0 (4.27) 30 (1.83) 25 (3630) 28 (4060) 1800 600 58.5 (129) 70.5 (155)
A90-*R01*S-60* 91.0 (5.55) 56 (3.42) 25 (3630) 28 (4060) 1800 600 72.5 (160) 93 (205)
A145-*R01*S-60* 145 (8.85) 83 (5.06) 25 (3630) 28 (4060) 1800 600 92.5 (204) 117.5 (259)
1. Whenever setting pressure, make sure the full cut-off pressure never
exceeds the maximum intermittent pressure. One Cycle Time
2. Care should be taken in cases of used at a higher pressure than the rated 1/5 of One Cycle
pressure, because operating terms may be restricted. For example, if (Max. 6s)
used as per maximum illustrated operating conditions, intermittent time
Pressure
at maximum flow is restricted to under 1/5 of one cycle time and under
six seconds simultaneously. Conditions may vary according to the actual 21 MPa (3050 PSI)
working pressure and delivery (inclination angle of the swash plate). {28 MPa (4060 PSI)} *1
Consult factory or Yuken sales representative for further information. Max.
Output
Flow
3. The table above shows specifications for using petroleum based oils.
Pumps (customized design) for special fluids are also available. Their
operating pressure and maximum shaft speed however differ from the 0
20 MPa (2900 PSI)
values in the table above depending on the fluid type. {27 MPa (3920PSI)} *1
Range of operating temperature and viscosities may differ from those
of petroleum based oils due to their characteristics. *1. Applicable only for "A70/90/145"
Specifications and Design numbers for Special Fluids
Allowable Temperature Viscosity Design Numbers for
Type Operating Pressure Maximum
Pump Shaft Speed Range Range Special Fluid
of MPa (PSI)
Series r/min (Occasion of Japanese
Fluids
°C (°F) mm2/s (SSU) Std. “JIS”) 3
Rated Intermittent Rated Max.
16(2320)
Water- A16 – A56 14(2030) 1 2
3230
{14(2030)} 1200 (1800) 0 - 50 (32 - 104)
Glycols
A70 – A145 21(3050) 21(3050) 6030
20 - 200(98 - 927)
16(2320)
Phosphate A16 – A56 14(2030) 1
3206
{14(2030)} 1200 (1800) 2
0 - 60 (32 - 140)
Ester Type
A70 – A145 21(3050) 21(3050) 6006
Polyol A16 – A56 16(2320) 16(2320) 32450
1800 1800 0 - 60 (32 - 140) 20 - 200(98 - 927)
Ester Type A70 – A145 21(3050) 21(3050) 60450
A70 -F R 01 B S -60 *
Series Direction of Control Pres. Adj. Range Port Design Design
Mounting
Number Rotation Type MPa (PSI) Position Number Std.
A10
3 B: 1.2 - 7 (170 - 1020) 4
F: Flange
C: 2.0 - 16 (290 - 2320) 12
(10.0 cm3/rev) Mtg.
H: 2.0 - 21 (290 - 3050)
A70 Viewed from
01: Pressure 60
(70.0 cm3/rev) Shaft End
F: Flange Compensator Refer to 2
1 Type B: 1.2 - 7 (170 - 1020)
A90 Mtg. R: Clockwise C: 1.5 - 16 (220 - 2320)
S: Side Port 60
(91.0 cm3/rev) (Normal) H: 1.8 - 21 (260 - 3050)
L: Foot K: 2.0 - 28 (290 - 4060)
A145 Mtg.
60
(145 cm3/rev)
1. Available to supply pump with anti-clockwise rotation. Consult 3. When A10 pump is used as the foot Mtg., order the Mtg. Bracket kit
Yuken for details. shown below separately. Refer to page 24 for dimensions of the Mtg.
2. Design Standards: None ........... Japanese Standard "JIS" bracket.
80 ............... European Design Standard Note: The mounting bracket kit consists of a mounting bracket, two hex.
950 ............. N. American Design Standard bolts and two plain washer.
"JIS" Design Std. Design Std. European Design Std. European Design Std.
Design Std. Design Std.
A16-*-R-01 Suction F5-06-A-10 F5-06-A-1080 F5-06-B-10 F5-06-B-1090 F5-06-C-10 F5-06-C-1090
A22-*-R-01 Discharge F5-06-A-10 F5-06-A-1080 F5-06-B-10 F5-06-B-1090 F5-06-C-10 F5-06-C-1090
A37-*-R-01 Suction F5-10-A-10 F5-10-A-1080 F5-10-B-10 F5-10-B-1090 F5-10-C-10 F5-10-C-1090
A56-*-R-01 Discharge F5-10-A-10 F5-10-A-1080 F5-10-B-10 F5-10-B-1090 F5-10-C-10 F5-10-C-1090
Suction F5-12-A-10 F5-12-A-1080 F5-12-B-10 F5-12-B-1090 F5-12-C-10 F5-12-C-1090
A70-*R01
Discharge F5-08-A-10 F5-08-A-1080 F5-08-B-10 F5-08-B-1090 F5-08-C-10 F5-08-C-1090
A90-*R01 Suction F5-16-A-10 F5-16-A-1080 F5-16-B-10 F5-16-B-1090 F5-16-C-10 F5-16-C-1090
A145-*R01 Discharge F5-10-A-10 F5-10-A-1080 F5-10-B-10 F5-10-B-1090 F5-10-C-10 F5-10-C-1090
1. In case of using socket welding flanges, there is a case where the operating pressure should be set lower than the normal because of strength of the
flanges. Therefore, please pay cautious attention to the operating pressure when the socket welding flanges are used.
2. As dimensions of the pipe flange mounting surface are conformed to SAE 4 Bolt Split Flange (Standard Pressure Series), pipe flanges conforming
to the SAE Standards can be used.
Details of the pipe flange kits are shown on page 824.
"A" Series
Drive Speed : 1500 r/min
Hydraulic Fluid : ISO VG32 oil
Oil Temperature :A10-A56: 50 °C (122 °F) [Viscosity 20 mm2/s (100 SSU)]
A70-A145: 40 °C (104 °F) [Viscosity 32 mm2/s (150 SSU)]
Result of Measurement
t1 t2 Full Cut-off
Pressure
* Response time except A10, A70, A90 and A145 is measured Yoke travel.
Efficiency
L /min L /min
80 Overall Efficiency 20 U.S.GPM 80 Overall Efficiency 20 U.S.GPM
5 5
Output Flow
60 15 4 60 15 4
Output Flow
Output Flow
Output Flow
HP kW 3 HP kW 3
Input Power
8 40 10
Input Power
8 40 10
8 6 2 8 6 2
wer
4 Powe
r 5 4 t Po 5
4 Input 1 4 Inpu 1
2 2
0 0 0 0
0 0
0 4 8 12 16 20 21 MPa 0 4 8 12 16 20 21 MPa
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
Pressure 3050 PSI Pressure 3050 PSI
Input Power
HP kW N=1500 r/min HP kW N=1800 r/min P=MPa (PSI)
8 8
10 10 P= 20 (2900)
7 P=MPa (PSI) 7 P= 18 (2610)
P= 20 (2900) P= 16 (2320)
8 6 P= 18 (2610) 8 6
P= 14 (2030)
P= 16 (2320)
Input Power
Input Power
5 P= 14 (2030) 5 P= 12 (1740)
6 P= 12 (1740) 6 P= 10 (1450)
4 P= 10 (1450) 4 P= 8 (1160)
P= 8 (1160) P= 6 (870)
4 3 4 3
P= 6 (870) P= 4 (580)
2 P= 4 (580) 2
P= 2 (290) P= 2 (290)
2 2
1 1
0 0
0 0
0 5 10 15 20 L /min 0 5 10 15 20 L /min
0 1 2 3 4 5 U.S.GPM 0 1 2 3 4 5 U.S.GPM
Output Flow Output Flow
1.2
80
0.8
1.0
60 1.0
.8 0.6 A10-FR01C
Drain
1500 r/min
.6 A10-FR01C 40
0.4 1800 r/min
0.5 A10-FR01B
.4 1500 r/min Flow Full
0.2 20
.2 A10-FR01B 800 r/min
1500,1
0 0
0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
Full Cut-off Pressure 3050 PSI Pressure 3050 PSI
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB (A) dB (A)
N=1500 r/min N=1800 r/min
70 70
Full Flow
Full Flow
Noise Level
Noise Level
60 60
50 50
Full Cut-off Full Cut-off
40 40
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
3050 PSI 3050 PSI
Pressure Pressure
"A" Series
100 100
Volumetric Efficiency Volumetric Efficiency
HP kW L /min
Overall Efficiency Overall Efficiency U.S.GPM
80 16 12 80 32
U.S.GPM Output Flow 8
HP kW L /min 28 7
Output Flow 7
12 9 60 24 12 9 60 24
6 6
Input Power
20 20
Output Flow
Output Flow
5 5
Input Power
Efficiency
Efficiency
8 6 16 4 8 6 16 4
Input Power
12 3 12 3
Input Power
4 3 8 2 4 3 8 2
4 1 4 1
0 0 0 0
0 0 0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Pressure Pressure
Input Power
Example: At a pressure of under 10 MPa (1450 PSI), a flow 20 L/min (5.3 U.S.GPM), and rotation 1500 r/min, the axial input becomes
about 3.7 kW (5 HP) as shown the dotted line in the graph.
HP kW HP kW P=MPa(PSI)
N=1500 r/min N=1800 r/min
16 12 P=MPa(PSI) 16 12 P= 20 (2900)
P= 20 (2900) P= 18 (2610)
10 P= 18 (2610) 10 P= 16 (2320)
12 P= 16 (2320) 12 P= 14 (2030)
8 P= 14 (2030) 8 P= 12 (1740)
Input Power
Input Power
P= 12 (1740) P= 10 (1450)
8 6 P= 10 (1450) 8 6 P= 8 (1160)
P= 8 (1160) P= 6 (870)
4 P= 6 (870) 4 P= 4 (580)
4 P= 4 (580) 4 P= 2 (290)
2 P= 2 (290) 2 P= 0.7 (100)
P= 0.7 (100)
0 0
0 0
0 5 10 15 20 25 30 L /min 0 5 10 15 20 25 30 L /min
0 1 2 3 4 5 6 7 8 U.S.GPM 0 1 2 3 4 5 6 7 8 U.S.GPM
Output Flow Output Flow
A16- *-R-01-C
0.5 A16- *-R-01-C 1
.5 50 N=1500 r/min
N=1500 r/min
A16- *-R-01-B
A16- *-R-01-B
0 0 1500,1800 r/min
0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Full Cut-off Pressure Pressure
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB(A) dB(A) N=1800 r/min
N=1500 r/min
80 80
70 70
Noise Level
Noise Level
Full Flow
Full Flow
60 60
50 50
Full Cut-off Full Cut-off
40 40
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Pressure Pressure
Efficiency
% N=1500 r/min % N=1800 r/min
Efficiency
Output Flow
Output Flow
12 60 30 8 12 60 30 8
Overall Efficiency
10 10
Input Power
Input Power
12 6 12 6
8 20 8 20
8 6 4 8 6 4
Input Power Input Power
4 10 4 10
4 2 4 2
2 2
0 0 0 0 0 0 0 0
0 4 8 12 16 MPa 0 4 8 12 16 MPa
0 500 1000 1500 2000 2320 PSI 0 500 1000 1500 2000 2320 PSI
Pressure Pressure
Input Power
Example: At a pressure of under 10 MPa (1450 PSI), a flow 30 L/min (7.9 U.S.GPM), and rotation 1500 r/min, the axial input becomes
about 5.4 kW (7.2 HP) as shown the dotted line in the graph.
HP HP
14 kW N=1500 r/min 14 kW N=1800 r/min
10 10
P=MPa(PSI) P= 14 (2030)
12 12
P= 14 (2030) P= 12 (1740)
8 8
10 P= 12 (1740) 10 P= 10 (1450)
P= 10 (1450)
P= 8 (1160)
Input Power
Input Power
8 6 8 6
P= 8 (1160)
P= 6 (870)
6 P= 6 (870) 6
4 4 P= 4 (580)
P= 4 (580)
4 P= 2 (290) 4
P= 2 (290)
2 P= 1 (145) 2
2 2 P= 1 (145)
0 0 P=MPa(PSI)
0 0
0 10 20 30 40 50 L /min 0 10 20 30 40 50 L /min
0 2 4 6 8 10 12 13 U.S.GPM 0 2 4 6 8 10 12 13 U.S.GPM
Output Flow Output Flow
0.5 1
50 A22- *-R-01-B
.5 N=1500 r/min
1500,1800 r/min
A22- *-R-01-B Full Flow
0 0
0 0
0 4 8 12 16 MPa 0 4 8 12 16 MPa
0 500 1000 1500 2000 PSI 0 500 1000 1500 2000 PSI
Full Cut-off Pressure 2320 Pressure 2320
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB(A) N=1500 r/min dB(A) N=1800 r/min
80 80
Noise Level
Noise Level
70 70
Full Flow Full Flow
60 60
Full Cut-off
Full Cut-off
50 50
0 2 4 6 8 10 12 14 MPa 0 2 4 6 8 10 12 14 MPa
0 500 1000 1500 2030 PSI 0 500 1000 1500 2030 PSI
Pressure Pressure
"A" Series
Efficiency
100 100
Efficiency
Output Flow
Output Flow
30 12 30 12
Input Power
Input Power
20 40 20 40
20 8 20 8
Input Power Input Power
10 20 10 20
10 4 10 4
0 0 0 0
0 0 0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Pressure Pressure
Input Power
Example: At a pressure of under 16 MPa (2320 PSI), a flow 45 L/min (11.9 U.S.GPM), and rotation 1500 r/min, the axial input becomes
about 12.6 kW (16.9 HP) as shown the dotted line in the graph.
HP P=MPa(PSI) HP P=MPa(PSI)
35 kW N=1500 r/min 35 kW N=1800 r/min P= 20 (2900)
25 P= 20 (2900) 25
P= 18 (2610)
30 P= 18 (2610) 30
P= 16 (2320) P= 16 (2320)
20 20 P= 14 (2030)
25 P= 14 (2030) 25
Input Power
Input Power
P= 12 (1740)
P= 12 (1740)
20 15 20 15 P= 10 (1450)
P= 10 (1450)
P= 8 (1160)
15 P= 8 (1160) 15
10 P= 6 (870) 10 P= 6 (870)
10 P= 4 (580) 10 P= 4 (580)
5 5 P= 2 (290)
5 P= 2 (290) 5 P= 1 (150)
P= 1 (150)
0 0
0 0
0 10 20 30 40 50 60 70 L /min 0 10 20 30 40 50 60 70 L /min
0 2 4 6 8 10 12 14 16 18 U.S.GPM 0 2 4 6 8 10 12 14 16 18 U.S.GPM
Output Flow Output Flow
3 A37- *-R-01-H
2 N=1800 r/min 120 2 N=1500 r/min
Drain
2 90
A37- *-R-01-C
1 60 1
1 N=1500 r/min A37- *-R-01-B
30 1500,1800 r/min
0 A37- *-R-01-B Full Flow
0
0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Full Cut-off Pressure Pressure
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB(A) N=1500 r/min dB(A) N=1800 r/min
80 80
70 70
Noise Level
Noise Level
Full Flow
Full Flow
60 60
Full Cut-off Full Cut-off
50 50
40 40
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Pressure Pressure
Efficiency
Efficiency
Overall Efficiency 80
80
Overall Efficiency
L /min
U.S.GPM
60 60 120
L /min Output Flow 30
HP U.S.GPM HP
Output Flow 100 100
60 kW 25 60 kW 25
Output Flow
40 80 20 40 80 20
Output Flow
Input Power
Input Power
40 60 15 40 60 15
Input Power
20 40 10 20 40 10
20 Input Power 20
20 5 20 5
0 0 0 0
0 0 0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Pressure Pressure
Input Power
Example: At a pressure of under 16 MPa (2320 PSI), a flow 70 L/min (18.5 U.S.GPM), and rotation 1500 r/min, the axial input becomes
about 20.8 kW (27.9 HP) as shown the dotted line in the graph.
kW N=1500 r/min P= 20 (2900) kW N=1800 r/min P= 20 (2900)
HP 40 HP 40
50 P= 18 (2610) 50 P= 18 (2610)
35 P= 16 (2320) 35 P= 16 (2320)
40 30 P= 14 (2030) 30 P= 14 (2030)
40
P= 12 (1740)
Input Power
P= 12 (1740)
Input Power
25 25 P= 10 (1450)
30 P= 10 (1450) 30
20 20 P= 8 (1160)
P= 8 (1160)
P= 6 (870)
20 15 P= 6 (870) 20 15
P= 4 (580)
10 P= 4 (580) 10 P= 2 (290)
10 P= 2 (290) 10
5 5 P=MPa(PSI)
P=MPa(PSI)
0 0
0 0
0 20 40 60 80 100 120 L /min 0 20 40 60 80 100 120 L /min
0 5 10 15 20 25 30 U.S.GPM 0 5 10 15 20 25 30 U.S.GPM
Output Flow Output Flow
3
150 A56- *-R-01-H
3 N=1800 r/min
Drain
2 2 A56- *-R-01-C
2 100
N=1500 r/min
Full Flow
1 1 A56- *-R-01-B
1 50 N=1500 r/min 1500,1800 r/min
0 0
0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Full Cut-off Pressure Pressure
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB(A) N=1500 r/min dB(A) N=1800 r/min
80 80
Noise Level
Noise Level
70 70
Full Flow Full Flow
60 60
Full Cut-off Full Cut-off
50 50
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Pressure Pressure
"A" Series
100
Efficiency
Efficiency
Overall Efficiency L /min
Overall Efficiency
80 80 140 U.S.GPM
Volumetric Efficiency L /min Output Flow 35
Output Flow
60 120 U.S.GPM 60 120
Output Flow 30 30
HP kW HP kW
Output Flow
80 60 100 80 60 100
25 Volumetric Efficiency 25
Input Power
Input Power
60 60
40 80 40
20 Input Power
40 Input Power 40
20 20
20 20
0 0
0 0
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Pressure 3630 Pressure 3630
Input Power
Example: At a pressure of under 20 MPa (2900 PSI), a flow 70 L/min (18.5 U.S.GPM), and rotation 1500 r/min, the axial input becomes
about 26 kW (35 HP) as shown the dotted line in the graph.
HP kW N=1500 r/min HP kW N=1800 r/min P=MPa(PSI)
80 60 80 60 P= 24 (3480)
P=MPa(PSI)
P= 24 (3480) P= 22 (3190)
50 P= 22 (3190) 50 P= 20 (2900)
60 P= 20 (2900) 60 P= 18 (2610)
40 P= 18 (2610) 40 P= 16 (2320)
Input Power
Input Power
P= 16 (2320) P= 14 (2030)
P= 14 (2030) P= 12 (1740)
40 30 40 30
P= 12 (1740) P= 10 (1450)
P= 10 (1450) P= 8 (1160)
20 P= 8 (1160) 20 P= 6 (870)
20 P= 6 (870) 20 P= 4 (580)
10 P= 4 (580) 10 P= 2 (290)
P= 2 (290)
0 0
0 0
0 20 40 60 80 100 120 140 L /min 0 20 40 60 80 100 120 140 L /min
0 10 20 30 35 U.S.GPM 0 10 20 30 35 U.S.GPM
Output Flow Output Flow
5 300 5
Full Cut-off Power
200
4 3 3
1500 r/min
2 2
2 100
1 1 Full Flow
1500,1800 r/min
0 0
0 0
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Full Cut-off Pressure 3630 Pressure 3630
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB(A) N=1500 r/min dB(A) N=1800 r/min
80 80
Noise Level
Noise Level
70 70 Full Flow
Full Flow
60 60
Full Cut-off Full Cut-off
50 50
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Pressure 3630 Pressure 3630
Efficiency
Efficiency
Output Flow
Output Flow 80
Output Flow
100 42
HP kW 36
80 60 130 80 60 150 40
34
Input Power
Input Power
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Pressure 3630 Pressure 3630
Input Power
Example: At a pressure of under 18 MPa (2610 PSI), a flow 110 L/min (29.1 U.S.GPM), and rotation 1500 r/min, the axial input
becomes about 34 kW (46 HP) as shown the dotted line in the graph.
HP P=MPa(PSI)
kW N=1500 r/min 100 kW N=1800 r/min P= 25 (3630)
70 P=MPa(PSI) 70 P= 24 (3480)
HP P= 25 (3630) P= 22 (3190)
80 60 P= 24 (3480) 80 60 P= 20 (2900)
P= 22 (3190) P= 18 (2610)
50 P= 20 (2900) 50 P= 16 (2320)
P= 18 (2610)
60 60 P= 14 (2030)
P= 16 (2320)
Input Power
Input Power
40 P= 14 (2030) 40 P= 12 (1740)
P= 12 (1740) P= 10 (1450)
40 30 P= 10 (1450) 40 30 P= 8 (1160)
P= 8 (1160) P= 6 (870)
20 P= 6 (870) 20 P= 4 (580)
20 P= 4 (580) 20
P= 2 (290) P= 2 (290)
10 10
0 0
0 0
0 20 40 60 80 100 120 140 L /min 0 20 40 60 80 100 120 140 160 L /min
0 5 10 15 20 25 30 35 U.S.GPM 0 5 10 15 20 25 30 35 40 45 U.S.GPM
Output Flow Output Flow
5 400
Full Cut-off Power
6 6
4 300
Drain
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
3630 3630
Full Cut-off Pressure Pressure
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB(A) N=1500 r/min dB(A) N=1800 r/min
80 80
Full Flow
Noise Level
70
Noise Level
70
Full Flow
60 60
Full Cut-off Full Cut-off
50 50
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
3630 3630
Pressure Pressure
"A" Series
Efficiency
Efficiency
Overall Efficiency Overall Efficiency
80 80
Volumetric Efficiency
60 60
L /min U.S.GPM Volumetric Efficiency L /min
Output Flow 220 58 270 U.S.GPM
Output Flow
70
56
Output Flow
210 Output Flow 260
HP kW HP kW 68
54
160 120 200 160 120 250 66
Input Power
Input Power
120 120
80 80 240
80 Input Power 80 Input Power
40 40
40 40
0 0
0 0
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Pressure 3630 Pressure 3630
Input Power
Example: At a pressure of under 20 MPa (2900 PSI), a flow 180 L/min (47.6 U.S.GPM), and rotation 1500 r/min, the axial input
becomes about 64 kW (86 HP) as shown the dotted line in the graph.
P=MPa(PSI) P=MPa(PSI)
P= 28(4060) P= 28(4060)
kW N=1500 r/min HP kW N=1800 r/min
P= 26(3770) P= 26(3770)
140 140
HP P= 24(3480) 180 P= 24(3480)
160 120 P= 22(3190) 160 120 P= 22(3190)
P= 20 (2900) P= 20 (2900)
140 P= 18 (2610) 140 P= 18 (2610)
100 100
120 P= 16 (2320) 120 P= 16 (2320)
Input Power
Input Power
80 P= 14 (2030) 80 P= 14 (2030)
100 100 P= 12 (1740)
P= 12 (1740)
80 60 P= 10 (1450) 80 60 P= 10 (1450)
P= 8 (1160) P= 8 (1160)
60 40 60
P= 6 (870) 40 P= 6 (870)
40 P= 4 (580) 40 P= 4 (580)
20 20 P= 2 (290) 20 P= 2 (290)
20
0 P= 1 (145) 0 P= 1 (145)
0 0
0 40 80 120 160 200 240 L /min 0 40 80 120 160 200 240 280 L /min
0 10 20 30 40 50 60 U.S.GPM 0 10 20 30 40 50 60 70 U.S.GPM
Output Flow Output Flow
10 7.5 7.5
1800 r/min Full Cut-off
400
1800 r/min
1500 r/min
Drain
5.0 5.0
1500 r/min
5
200
2.5 2.5
Full Flow
1500,1800 r/min
0 0
0 0
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Full Cut-off Pressure 3630 Pressure 3630
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB(A) N=1500 r/min dB(A) N=1800 r/min
90 90
Noise Level
Noise Level
80 80
Full Flow
Full Flow
70 70
Full Cut-off
Full Cut-off
60 60
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Pressure 3630 Pressure 3630
(2.56)
65
(2.07)
(4.06)
(3.35)
103
85
(6.57)
167
(1.61)
41
(1.22)
(.47)
12
31
19.02(.7488) Dia.
82.50(3.2480) Dia.
21.24(.836)
21.08(.830)
2 3 2 3 10.5
19.05(.7500)
82.55(3.2500)
Suction Port 25 25 Discharge Port 106
(.41)
RC 1/2 Thd. (.98) (.98) RC 1/2 Thd. (4.17)
131
64.5 64.5 130
(5.16) (5.12)
(2.54) (2.54) 156
93(3.66) Dia.
(6.14)
159.5
(6.28)
2 3 2 3
Suction Port C C Discharge Port A
"E" Thd. "E" Thd.
B B 159.5(6.28)
For other dimensions, refer to above Pressure Adj. Range "C" & "H".
"A" Series
M 10
A16/A22-F-R-01-*-K-3280 3/8 BSP.F
A16/A22-F-R-01-*-K-3290 SAE #8 3/8-16 UNC
(3.78)
109
(.98)
96
(2.44)
(7.36)
62
187
(1.874)
47.6
(.47)
(.71)
12
18
19.02(.7488) Dia.
21.24(.836)
21.08(.830)
82.50(3.2480) Dia.
19.05(.7500)
R12
95(3.74) Dia. (R .47)
82.55(3.2500)
Suction Port 22.2 "D" Thd. 17(.67) Deep
12 106
19(.75) Dia. (.874) 8 Places
Discharge Port (.47) (4.17)
65
172 130
(2.56) 19 (.75) Dia.
(6.77) (5.12)
188
(7.40)
Install the pump so that the "Filling Port" is at the top.
(3.15)
(.59)
(.55)
15
14
3(.12)
80
50 56.5 95
(1.969) (2.22) (3.74)
95 27.5 72.5 72.5
(3.74) (1.08) (2.854) (2.854)
180
(7.09)
For other dimensions, refer to "Flange Mtg.".
DIMENSIONS IN
Side Port Type
MILLIMETRES (INCHES)
Flange Mtg.: A16-F-R-01-*-S-K-32/3280/32950
A22-F-R-01-*-S-K-32/3280/32950 Discharge Port 19 (.75) Dia.
Rear Side
"D" Thd. 17 (.67) Deep Suction Port 19 (.75) Dia.
4 Places (Both Sides) 44.5
188 Fully Extended (1.75)
(7.40) 219(8.62)
78(3.07) 109(4.29)
47.6(1.874)
74 74 22.2
(2.91) (2.91) (.874)
Surface of Suction Port Surface of Discharge Port 150.5
(5.93)
For other dimensions, refer to "Axial Port Type".
Foot Mtg. Type; Mounting bracket is common to that of "Axial Port Type".
(4.13)
112
(.98)
105
25
(2.68)
(.55)
68
(7.95)
14
(2.311)
202
58.7
22.20(.8740) Dia.
25.01(.985)
24.85(.978)
101.55(3.9980) Dia.
R14
22.23(.8752)
(R .55)
101.60(4.0000)
120(4.72) Dia.
Suction Port 30.2 "D" Thd. "E" Deep 12
8 Places 146
32(1.26) Dia. (1.189) (.47) (5.75)
72 Discharge Port 195 174
(2.83) 32 (1.26) Dia. (7.68) (6.85)
202
(7.95)
Install the pump so that the "Filling Port" is at the top.
102
3(.12)
15
14
60 74 120
(2.362)(2.91) (4.72)
115 39 95 95
(4.53) (1.54) (3.740) (3.740)
230
(9.06)
For other dimensions, refer to "Flange Mtg.".
DIMENSIONS IN
Side Port Type
MILLIMETRES (INCHES)
Flange Mtg.: A37-F-R-01-*-S-K-32/3280/32950
Discharge Port 32 (1.26) Dia.
"D" Thd. "E" Deep Rear Side
4 Places (Both Sides) Suction Port 32 (1.26) Dia.
202 Fully Extended 59
(7.95) 247(9.72) (2.32)
112(4.41)
58.7(2.311)
202(7.95)
86 86 30.2
(3.39) (3.39) (1.189)
Surface of Surface of 178.5
Suction Port Discharge Port (7.03)
For other dimensions, refer to "Axial Port Type".
Foot Mtg. Type; Mounting bracket is common to that of "Axial Port Type".
"A" Series
Fully Extended (2.44)
Flow Adj. Screw Lock Nut 17(.67) Hex. Filling Port 1
17(.67) Hex. 259.5(10.22) [22(.87) Hex. Head Plug Furnished]
50.5(1.99) 9.5 Surface of
DEC. Pressure Adj. Screw 2
(.37) Drain Port "C" Thd. Drain Port
17(.67) Hex. (Both Sides)
13 19 43.5(1.71) 41 49
(.51) (.75) INC. (1.61) (1.93)
35.32(1.391)
35.14(1.383)
40 7.97(.3138)
Dia.
(1.57) 7.94(.3126)
(5.43)
101.60(4.0000)
101.55(3.9980)
138
(3.54)
(3.03)
(.55)
90
14
77
(9.29)
(2.311)
236
(.98)
58.7
25
31.70(1.2480) Dia.
R14
31.75(1.2500)
Suction Port 120(4.72) Dia. (R.55)
"D" Thd. "E" Deep
35(1.38) Dia. 30.2 12 146
8 Places (.47) (5.75)
(1.189)
76 Discharge Port 207 174
(2.99) 32 (1.26) Dia. (8.15) (6.85)
232
(9.13)
(4.02)
(.55)
(.59)
102
3(.12)
14
15
60 77 120
(2.362) (3.03) (4.72)
115 42 95 95
(4.53) (1.65) (3.740) (3.740)
230
(9.06)
For other dimensions, refer to "Flange Mtg.".
DIMENSIONS IN
Side Port Type MILLIMETRES (INCHES)
Flange Mtg.: A56-F-R-01-*-S-K-32/3280/32950 Discharge Port 32 (1.26) Dia.
Rear Side
"D" Thd. "E" Deep
Suction Port 35 (1.38) Dia.
4 Places (Both Sides)
232 Fully Extended 62
(9.13) 259.5(10.22) (2.44)
(5.43)
138
58.7(2.311)
(9.29)
236
(7.17)
Y 4 Places X
182
14(.55)
(3.54)
90
(2.063)
(4.504)
(7.09)
52.4
114.4
180
18(.71)
14(.55)
31.70(1.2480) Dia.
(4.65)
118
126.95(4.9980) Dia.
31.75(1.2500)
35.32(1.391)
35.14(1.383)
Discharge Port
26(1.02) Dia.
127.00(5.0000)
16
26.2 (.63) 114.4 35(1.38) Dia.
(1.031) 18 (4.504) Spotface
"E" Thd. 17(.67) Deep (From Rear)
(.71) 134
4 Places 2 Places
246.5 (5.28)
(9.70) 181
(7.126)
211
(8.31)
Flow Adj. Screw Eye Bolt
17(.67) Hex. Pressure Adj. Screw 1 M10
17(.67) Hex. Filling Port
DEC. [22(.87) Hex. Head Plug Furnished]
INC.
Suction Port
38(1.50) Dia.
(2.752)
69.9
View Arrow Y
View Arrow X
F
Model Numbers "C" Thd. "D" Thd. "E" Thd.
mm (IN.)
A70-FR01*S-60 Rc 3/4
M 12 M 10 19 (.75)
A70-FR01*S-6080 3/4 BSP.F
A70-FR01*S-60950 SAE #12 1/2-13 UNC 3/8-16 UNC 21 (.83)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg.: A70-LR01*S-60/6080/60950
42.5
(1.67)
(5.00) Dia.
(5.12)
(.94)
130
24
(.12)
3
(1.02)
125 77 171
26
"A" Series
105 105
329(12.95)
(4.13) (4.13)
119.5 23(.91)
Surface of Drain Port 68 68 Surface of Drain Port
(4.70)
13(.51) (2.68) (2.68)
63(2.48)
(7.50)
(2.311)
190.5
58.7
(4.45)
113
Y 9.56(.3764) X
(6.362)
161.6
9.53(.3752)
(5.00)
127
38.05(1.4980) Dia.
152.35(5.9980) Dia.
Discharge Port
42.36(1.668)
42.18(1.661)
32(1.26) Dia. 21.5(.85) Dia. Through R22
22
38.10(1.5000)
152.40(6.0000)
30.2 (.87) 39(1.54) Dia. Spotface 161.6 (R.87)
"E" Thd. "F" Deep (1.189) (From Rear) (6.362)
4 Places 23
(.91) 4 Places
270
(10.63) 3
Case Drain Port
5(.2) Hex. Soc.
Eye Bolt
Pressure Adj. Screw M10
Flow Adj. Screw 17(.67) Hex. 1
17(.67) Hex. Filling Port
[27(1.06) Hex. Head Plug Furnished]
INC. Suction Port
DEC. 48(1.89) Dia.
(3.063)
77.8
View Arrow Y
"D" Thd. "F" Deep
4 Places
42.9
1. Install the pump so that the "Filling Port" is at the top. (1.689)
2. Use either port of the two drain ports at your option. 270
Keep the remaining port plugged. (10.63)
3. Case drain port is available for use when draining hydraulic
fluid from pump casing. View Arrow X
F
Model Numbers "C" Thd. "D" Thd. "E" Thd.
mm (IN.)
A90-FR01*S-60 Rc 3/4
M 12 M 10 19 (.75)
A90-FR01*S-6080 3/4 BSP.F
A90-FR01*S-60950 SAE #12 1/2-13 UNC 7/16-14 UNC 21 (.83)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg.: A90-LR01*S-60/6080/60950
(.12)
3
(7.81)
198.5
11.14
11.11
(4.33)
X
110
.4386
(9.000)
(2.311)
228.6
.4374
58.7
(5.55)
141
Discharge Port
44.40(1.7480) Dia.
152.35(5.9980) Dia.
49.39(1.944)
49.21(1.937)
32(1.26) Dia. 44.45(1.7500)
152.40(6.0000)
R22 21.5(.85) Dia. Through
30.2 24 228.6
"E" Thd. "H" Deep (R .87) 39(1.54) Dia. Spotface
(1.189) (.94) (9.000)
4 Places (From Rear)
26 273 4 Places
3
Case Drain Port (1.02) (10.75)
5(.2) Hex. Soc. 299.5
(11.79)
1
Filling Port
[27(1.06) Hex. Head Plug Furnished]
Eye Bolt
M10
Pressure Adj. Screw
17(.67) Hex.
INC. 1. Install the pump so that the "Filling Port" is at the top.
Suction Port
48(1.89) Dia. 2. Use either port of the two drain ports at your option. Keep the
remaining port plugged.
(3.063)
3. Case drain port is available for use when draining hydraulic fluid
77.8
42.9
(1.689)
299.5 Dimensions mm (IN.)
(11.79) Model Numbers "C" Thd. "D" Thd. "E" Thd.
F H
A145-FR01*S-60 Rc 3/4
View Arrow X M 12 M 10 19 (.75) 19 (.75)
A145-FR01*S-6080 3/4 BSP.F
A145-FR01*S-60950 SAE #12 1/2-13 UNC 7/16-14 UNC 21 (.83) 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg.: A145-LR01*S-60/6080/60950
22(.87) Dia. Through
43(1.69) Dia. Spotface
4 Places
(7.37)
187.3
(.12)
3
29(1.14)
30(1.18)
A10-FR01-B-12
A10-FR01C/H-12/1280/12950
"A" Series
38 35 64 23 37 36 39 25 23 22 21 20 15 18 19 16 40 28 27 14 29 12 11 1
10
7
8
6
5
2
9
4
3
37 41 33 34 42 24 17 32 30 31 26 13
51 52 53 54 55 56 59 57 58 63 60 62 61 71 70 73 72
A16/A22/A37/A56-*-R-01-*-*-K-32/3280/32950
56
25 40 35 9 43 2 44 3 25 11 52 60 31 4 22 1 32
27
61
X 58
X
29
57
51
5
55
54
49
53
28 50 7 30 19 33 20 17 8 10 21
23 43 37 14 18 15 13 24 12 34 39 16 41 36 6 42
47
46
38
45
Section X-X
A70/A90-*R01*S-60/6080/60950
"A" Series
25 26 27 28 29 30 31 32 33
63
55 27 26 55 37 12 32 56 36 67 3 1 4
53
A 51
46
9
35 42
P
45 X X
Q 60
Z
64 62
34 6
54 40
Z 47 38
48
52
66
39 25 2 61 5 33 31 13 28 16 15 14 17 29 65 30
23 58 44 11 7 8 59 22 44 70
A145-*R01*S-60/6080/60950
58 69 51 52 36 65 62 46 65 14 8 7 33 16 3 60 37 73 59 5 76
25 9
A
59 44
X X
67 54
70 41
35 68
27 4
29 64
74 39
30 57
40 28
53 2 34 26 11 6 1 32 38 10 13 12 16 71 31 72
26 27 28 29 30 31 32 33 34
24 62 56 19 17 50 48 66 23
57 63 15 46
20
21 45 43 18 22 59 47 49
Section X-X Detail "A"
"A" Series
Graphic Symbol Performance Characteristics
PL PH
Output Flow
SOL SOL
"OFF" "ON"
M
O
PL PH
Pressure
Specifications
Geometric Minimum Operating Pressure Shaft Speed Range Approx. Mass
MPa (PSI) Minimum r/min kg (lbs.)
Displacement Adj. Flow
Model Numbers Adj. Pres.
cm3/rev cm3/rev 2 1 Flange Foot
(cu. in. /rev) (cu. in. /rev) Rated Intermittent MPa (PSI) Max. Min.
Mtg. Mtg.
A16-*-R-02-*-K*-32* 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 1.2 (170) 1800 600 24.5 (54.0) 26.7 (58.9)
A22-*-R-02-*-K*-32* 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 1.2 (170) 1800 600 24.5 (54.0) 26.7 (58.9)
A37-*-R-02-*-K*-32* 36.9 (2.25) 10 (.61) 16 (2320) 21 (3050) 1.2 (170) 1800 600 36 (79.4) 40.3 (88.9)
A56-*-R-02-*-K*-32* 56.2 (3.43) 12 (.73) 16 (2320) 21 (3050) 1.2 (170) 1800 600 43 (94.8) 47.3 (104)
A70-*R02S*-60* 70.0 (4.27) 30 (1.83) 25 (3630) 25 (3630) 2 (290) 1800 600 63.5 (140) 75.5 (166)
A90-*R02S*-60* 91.0 (5.55) 56 (3.42) 25 (3630) 25 (3630) 2 (290) 1800 600 80.5 (178) 101 (223)
A145-*R02S*-60* 145 (8.85) 83 (5.06) 25 (3630) 25 (3630) 2 (290) 1800 600 97.5 (215) 122.5 (270)
1. Whenever setting pressure, make sure the full cut-off pressure never 2. When operating the pump exceeding the rated pressure, operating
exceeds the maximum intermittent pressure. conditions are restricted. Refer to page 33 for the details.
Solenoid Ratings
Solenoid operated directional valves used on these pumps are YUKEN DSG-01 series (standard type). For detail
specifications of solenoid operated directional valves, refer to page 345.
A70 AC
A100, A120 60
(70.0 cm3/rev) Viewed from
F: A200, A240
Shaft End 02:
Flange Mtg.
A90 Solenoid Two S: DC 2
60 Refer to
(91.0 cm3/rev) R: Prsuure Control Side Port D12, D24
L: 1
D48
Clockwise Type
Foot Mtg.
A145 (Normal) R(AC DC Rectified)
60
(145 cm3/rev) R100, R200
1. Available to supply pump with anti-clockwise rotation. Consult 2. Design Standards: None ........... Japanese Standard "JIS"
Yuken for details. 80 ............... European Design Standard
950 ............ N. American Design Standard
Performance Characteristics
For performance characteristics, refer to models of pressure compensator type on page 37 to 43.
"A" Series
Fully Extended
256.5(10.10) 2 3
Pilot Port "PP2"
141.5 "E" Thd.
(5.57)
95 136
74.5
(3.74) (5.35)
Lock Nut (2.93)
112 44.5 Electrical Conduit
14(.55) Hex. 3 51.5 Connection
(4.41) (1.75)
(.12) (2.03) "D" Thd. (Both Ends)
59 6.5
1
(2.32) (.26) Filling Port
26.5 [22(.87) Hex. Head Plug Furnished]
"PP1" (1.04) Drain Port
"PP2"
"C" Thd.
(7.66)
194.5
(6.93)
4.79(.1886)
176
(5.71)
145
(10.73)
(4.61)
25
272.5
4.76(.1874)
117
(3.78)
(.98)
96
(2.44)
X
62
18(.71)
(.47)
12
19.02(.7488) Dia.
82.50(3.2480) Dia.
R12(R.47)
21.24(.836)
21.08(.830)
82.55(3.2500)
19.05(.7500)
95(3.74) Dia.
12 106
Lock Nut (.47)
17(.67) Hex. (4.17)
172 130
(6.77) (5.12)
Pressure Adj. Screw (PH)
188
14(.55) Hex.
(7.40)
Works at Solenoid INC.
Energised
Pilot Port "PP1"
2 A16-F-R-02-K-*-3280
16 23
(.63) (.91) "E" Thd. A22-F-R-02-K-*-3280
Cable Departure
3(.12) Pressure Adj. Screw (PL) Cable Applicable:
14(.55) Hex. Outside Dia. ...... 8-10mm(.31-.39 in.)
Conductor Area ...... Not Exceeding 1.5mm2(.0023 Sq. IN.)
Works at Solenoid INC.
De-energised 132.5 77.6
(5.22) (3.06)
Flow Adj. Screw d 51.5
5(.20) Hex. Soc. (2.03)
(6.34)
161
DEC.
(1.874)
47.6
a
b
1. Install the pump so that the "Filling Port" is Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd.
at the top.
A16/A22-F-R-02-K-*-32 Rc 3/8 G 1/2 Rc 1/4
2. The pilot port provided is for connecting a M10
control valve, if multistage pressure control A16/A22-F-R-02-K-*-3280 3/8 BSP.F 1/4 BSP. Tr
is required. A16/A22-F-R-02-K-*-32950 SAE #8 1/2 NPT SAE #4 3/8-16 UNC
3. The pilot port "PP2" is not provided for
N.American Design Standard.
DIMENSIONS IN MILLIMETRES (INCHES)
(7.81)
198.5
(7.09)
180
(5.87)
(11.36)
32(1.26) 6.38(.2512)
149
288.5
(4.76)
121
(4.13)
6.35(.2500)
105
(2.68)
68
(2.311)
58.7
(.55)
(.98)
25
14
R14(R.55)
22.20(.8740) Dia.
101.55(3.9980) Dia.
25.01(.985)
24.85(.978)
120(4.72) Dia.
101.60(4.0000)
22.23(.8752)
Front Side : Discharge Port 32(1.26) Dia. 146
30.2 12
Rear Side : Suction Port 32(1.26) Dia. (5.75)
(1.189) (.47)
178.5 174
"F" Thd. "H" Deep (6.85)
4 Places (7.03)
202
(7.95)
2
13 26 Pilot Port "PP1"
Pressure Adj. INC. (.51) (1.02) "E" Thd.
Screw (PH)
14(.55) Hex.
6(.24)
Pressure Adj. Screw (PL) A37-F-R-02-S-K-*-3280
Works at Solenoid 14(.55) Hex. Cable Departure
Energised Works at Solenoid INC. Cable Applicable:
De-energised Outside Dia. ...... 8-10mm(.31-.39 IN.)
Flow Adj. Screw Conductor Area ...... Not Exceeding 1.5mm2(.0023 Sq. IN.)
5(.20) Hex. Soc. 155.5 74.6
(6.12) (2.94)
(6.50)
165
DEC. d 48.5
(1.91)
a
b
86 86
(3.39) (3.39)
Surface of Surface of
Suction Port Discharge Port
mm (IN.)
View Arrow X Model Numbers
a b d
1. Install the pump so that the "Filling Port" is at the top. A37-F-R-02-S-K-A*-3280 197 (7.76) 185 (7.28) 39 (1.54)
2. The pilot port provided is for connecting a control A37-F-R-02-S-K-D*-3280 208 (8.19) 196 (7.72) 39 (1.54)
valve, if multistage pressure control is required. A37-F-R-02-S-K-R*-3280 211 (8.31) 189.2 (7.45) 53 (2.09)
3. The pilot port "PP2" is not provided for N.American
For other dimensions, refer to 32/32950 design.
Design Standard.
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A37-F-R-02-S-K-*-32 Rc 1/2 G 1/2 Rc 1/4
M10 19 (.75)
A37-F-R-02-S-K-*-3280 1/2 BSP.F 1/4 BSP. Tr
A37-F-R-02-S-K-*-32950 SAE #10 1/2 NPT SAE #4 7/16-14 UNC 20 (.79)
"A" Series
292(11.50)
Lock Nut 177
17(.67) Hex. (6.97) 3 4
Pilot Port "PP2"
95 171.5 "E" Thd.
(3.74) (6.75) 71.5
Lock Nut 147.5 62(2.44) (2.81)
Electrical Conduit
14(.55) Hex. (5.81) 6 48.5 Connection
1 (.24)
50.5(1.99) 9.5(.37) Filling Port (1.91) "D" Thd. (Both Ends)
[22(.87) Hex. Head Plug Furnished]
43.5(1.71) Drain Port 2
"PP1" "C" Thd. (Both Sides)
5
"PP2" 41 49 5
(8.80)
223.5
(8.07)
40
205
7.97(.3138) (1.61) (1.93)
(6.85)
174
(5.75)
(1.57)
(12.66)
7.94(.3126)
321.5
X
146
(3.54)
(3.03)
58.7(2.311)
90
77
(.98)
(.55)
25
14
Dia.
101.55(3.9980) Dia.
35.32(1.391)
35.14(1.383)
R14(R.55)
101.60(4.0000)
31.75(1.2500)
31.70(1.2480) 120(4.72) Dia.
Front Side : Discharge Port 32(1.26) Dia. 146
30.2 12
Rear Side : Suction Port 35(1.38) Dia. (5.75)
(1.189) (.47)
"F" Thd. "H" Deep 207 174
4 Places (8.15) (6.85)
232
(9.13)
3
13 26 Pilot Port "PP1"
Pressure Adj. (.51) (1.02) "E" Thd.
Screw (PH) INC. Pressure Adj. Screw (PL) A56-F-R-02-S-K-*-3280
14(.55) Hex. 6(.24) 14(.55) Hex.
Works at Solenoid Works at Solenoid INC. Cable Departure
Energised De-energised Cable Applicable:
Outside Dia. ...... 8-10mm(.31-.39 IN.)
Flow Adj. Screw Conductor Area ...... Not Exceeding 1.5mm2(.0023 Sq. IN.)
5(.20) Hex. Soc.
168
(7.48)
74.6
190
DEC. (6.61)
(2.94)
d
48.5
(1.91)
a
100 100 b
(3.94) (3.94)
Surface of Surface of
Suction Port Discharge Port
View Arrow X
1. Install the pump so that the "Filling Port" is at the top. mm (IN.)
Model Numbers
2. Use either port of two drain ports at your option. a b d
Keep the remaining port plugged.
A56-F-R-02-S-K-A*-3280 222 (8.74) 210 (8.27) 39 (1.54)
3. The pilot port provided is for connecting a control
A56-F-R-02-S-K-D*-3280 233 (9.17) 221 (8.70) 39 (1.54)
valve, if multistage pressure control is required.
A56-F-R-02-S-K-R*-3280 236 (9.29) 214.2 (8.43) 53 (2.09)
4. The pilot port "PP2" is not provided for N.American
Design Standard. For other dimensions, refer to 32/32950 design.
5. Dimensions show surface of drain port.
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A56-F-R-02-S-K-*-32 Rc 3/4 G 1/2 Rc 1/4
M10 19 (.75)
A56-F-R-02-S-K-*-3280 3/4 BSP.F 1/4 BSP. Tr
A56-F-R-02-S-K-*-32950 SAE #12 1/2 NPT SAE #4 7/16-14 UNC 20 (.79)
(9.29)
(1.57)
(8.56)
217.5
236
202.5
(7.97)
X 7.94(.3126)
186.5
(7.34)
Y
18(.71)
14(.55)
(3.54)
90
(2.063)
(4.504)
52.4
(7.09)
114.4
180
(4.65)
118
Discharge Port
31.70(1.2480) Dia.
126.95(4.9980) Dia.
35.32(1.391)
35.14(1.383) 35(1.38) Dia. Spotface
26(1.02) Dia.
(From Rear)
31.75(1.2500)
127.00(5.0000)
19.5 2 Places
"F" Thd. 26.2 (.77) 114.4
17(.67) Deep (1.031) 16 (4.504)
4 Places (.63) 134
18 (5.28)
(.71) 181
246.5 (7.126)
(9.70) 211
(8.31)
INC. Eye Bolt
Pressure Adj. Screw (PH) 87.5 3 M10
14(.55) Hex. Pilot port "PP1" 1
(3.44) Filling Port
"E" Thd.
Works at Solenoid 64.5 [22(.87) Hex. Head Plug Furnished]
Energised (2.54)
10 Suction Port
Pressure Adj. Screw (PL) 38(1.50) Dia.
(.39)
14(.55) Hex.
(2.752)
Works at Solenoid INC.
69.9
De-energised
Flow Adj. Screw
17(.67) Hex.
DEC. 5 "H" Thd. "J" Deep
Case Drain Port 4 Places
5(.20) Hex. Soc. 35.7
View Arrow X
(1.406)
246.5
(9.70)
View Arrow Y
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" Thd. "J" mm (IN.)
A70-FR02S*-60 Rc 3/4 G 1/2 Rc 1/4
M10 M12 19 (.75)
A70-FR02S*-6080 3/4 BSP.F 1/4 BSP. Tr
A70-FR02S*-60950 SAE #12 1/2 NPT SAE #4 7/16-14 UNC 1/2-13 UNC 21 (.83)
DIMENSIONS IN
MILLIMETRES (INCHES)
mm (IN.)
Model Numbers
a b d Foot Mounting Type
A70-FR02SA*-6080 235 (9.25) 223 (8.78) 39 (1.54) Mounting bracket is common to that of pressure compensator
A70-FR02SD*-6080 246 (9.69) 234 (9.21) 39 (1.54) model. Refer to page 48 for the dimensions of mounting
bracket.
A70-FR02SR*-6080 249 (9.80) 227.2 (8.94) 53 (2.09)
For other dimensions, refer to 60/60950 design.
"A" Series
Drain Port (2.68) (2.68) Drain Port
(10.37) (3.74) 2.5 52
119.5 23(.91) 3 4
Pilot Port "PP2" (.1) (2.05) 9.56(.3764)
(4.70) "E" Thd. 9.53(.3752)
13(.51)
63
(9.67)
245.5
(8.90)
(2.48)
(8.35)
226
(7.72)
212
196
X
(4.45)
Y
113
(6.362)
(2.311)
161.6
58.7
(5.00)
127
Discharge Port 38.05(1.4980) Dia.
152.35(5.9980) Dia.
42.36(1.668)
42.18(1.661)
32(1.26) Dia.
21.5 (.85) Dia. Through
38.10(1.5000)
152.40(6.0000)
22 R22(R.87)
30.2 39(1.54) Dia. Spotface 161.6
(.87)
(1.189) 23 (From Rear) (6.362)
"F" Thd. "J" Deep
4 Places 4 Places
(.91)
270
(10.63)
5
Case drain Port
5(.20) Hex. Soc. Fully Extended
3 Eye Bolt
Pilot Port "PP1" M10 379(14.92)
22.5
(.89) "E" Thd. 258 95
1
(10.16) Electrical Conduit Connection
Filling Port (3.74)
Pressure Adj. Screw (PH) 2.5 "D" Thd. (Both Ends)
(.10) [27(1.06) Hex. Head Plug Furnished]
14(.55) Hex.
Works at Solenoid INC. Pressure Adj. Screw (PL)
Energised 14(.55) Hex.
(7.72)
196
(6.61)
Works at Solenoid INC.
168
De-energised
(3.46)
88
(3.063)
77.8
Flow Adj. Screw
17(.67) Hex.
DEC. Suction Port
48(1.89) Dia.
View Arrow X
42.9 "H" Thd. "K" Deep
(1.689) 4 Places
270
(10.63)
View Arrow Y
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" Thd. "J" mm (IN.) "K" mm (IN.)
A90-FR02S*-60 Rc 3/4 G 1/2 Rc 1/4
M10 M12 19 (.75) 19 (.75)
A90-FR02S*-6080 3/4 BSP.F 1/4 BSP. Tr
A90-FR02S*-60950 SAE #12 1/2 NPT SAE #4 7/16-14 UNC 1/2-13 UNC 20 (.79) 21 (.83)
DIMENSIONS IN
MILLIMETRES (INCHES)
mm (IN.)
Model Numbers Foot Mounting Type
a b d
Mounting bracket is common to that of pressure compensator
A90-02FRSA*-6080 244 (9.61) 232 (9.13) 39 (1.54)
model. Refer to page 49 for the dimensions of mounting
A90-02FRSD*-6080 255 (10.04) 243 (9.57) 39 (1.54) bracket.
A90-02FRSR*-6080 258 (10.16) 236.2 (9.30) 53 (2.09)
For other dimensions, refer to 60/60950 design.
(9.74)
247.5
(8.43)
(7.80)
214
198
Y
(4.33)
110
(9.000)
(2.311)
228.6
58.7
(5.55)
141
Discharge Port
152.40(6.0000) Dia.
44.40(1.7480) Dia.
49.39(1.944)
49.21(1.937)
32(1.26) Dia.
44.45(1.7500)
152.35(5.9980)
"F" Thd.
30.2 24 39(1.54) Dia. Spotface 228.6 R22(R .87)
"J" Deep (From Rear)
4 Places (1.189) (.94) (9.000)
4 Places
26 273
5
Case Drain Port (1.02) (10.75)
5(.20) Hex. Soc. 299.5
(11.79) Electrical Conduit Connection
"D" Thd. (Both Ends)
Eye Bolt
M10 279 95
(10.98) (3.74)
1
3 Filling Port
Pressure Adj. Screw (PH) Pilot Port "PP1" [27(1.06) Hex. Head Plug Furnished]
14(.55) Hex. 66.5 "E" Thd.
Works at Solenoid INC. (2.62)
Energised Suction Port
12 Pressure Adj. Screw (PL) 48(1.89) Dia.
(.47)
14(.55) Hex.
(3.063)
77.8
Works at Solenoid INC.
De-energised
Flow Adj. Screw
"H" Thd. "K" Deep
(9.02)
17(.67) Hex.
229
4 Places
DEC.
42.9
(1.689)
299.5
(11.79)
View Arrow X
View Arrow Y
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" Thd. "J" mm (IN.) "K" mm (IN.)
A145-FR02S*-60 Rc 3/4 G 1/2 Rc 1/4
M10 M12 19 (.75) 19 (.75)
A145-FR02S*-6080 3/4 BSP.F 1/4 BSP. Tr
A145-FR02S*-60950 SAE #12 1/2 NPT SAE #4 7/16-14 UNC 1/2-13 UNC 20 (.79) 21 (.83)
DIMENSIONS IN
MILLIMETRES (INCHES)
mm (IN.)
Model Numbers
a b d Foot Mounting Type
A145-FR02SA*-6080 246 (9.69) 234 (9.21) 39 (1.54) Mounting bracket is common to that of pressure compensator
model. Refer to page 50 for the dimensions of mounting
A145-FR02SD*-6080 257 (10.12) 245 (9.65) 39 (1.54) bracket.
A145-FR02SR*-6080 260 (10.24) 238.2 (9.38) 53 (2.09)
For other dimensions, refer to 60/60950 design.
"A" Series
Output Flow
SOL SOL
"OFF" "ON"
M
O
Pressure
Specifications
Geometric Minimum Shaft Speed
Operating Pressure
Displacement Adj. Flow Unloading Pressure Range
Model Numbers MPa (PSI)
cm3/rev cm3/rev MPa (PSI) r/min
(cu. in. /rev) (cu. in. /rev) Rated Intermittent Max. Min.
A16-*-R-03-*-K-*-32* 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 1.2 (170) 1800 600
A22-*-R-03-*-K-*-32* 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 1.2 (170) 1800 600
A37-*-R-03-*-K-*-32* 36.9 (2.25) 10 (.61) 16 (2320) 21 (3050) 1.2 (170) 1800 600
A56-*-R-03-*-K-*-32* 56.2 (3.43) 12 (.73) 16 (2320) 21 (3050) 1.2 (170) 1800 600
A70-*R03S*-60 * 70.0 (4.27) 30 (1.83) 25 (3630) 25 (3630) 1.2 (170) 1800 600
A90-*R03S*-60 * 91.0 (5.55) 56 (3.42) 25 (3630) 25 (3630) 1.2 (170) 1800 600
A145-*R03S*-60 * 145 (8.85) 83 (5.06) 25 (3630) 25 (3630) 1.2 (170) 1800 600
A16
32
(15.8 cm3/rev) AC
F: Viewed from A100,A120
None:
A22 Flange Shaft End 03: A200,A240
Axial Port 32
(22.2 cm3/rev) Mtg. Pressure K: DC Refer to
2
Compensator Keyed Shaft D12,D24
A37 L: R: with D48
1
S: 32
(36.9 cm3/rev) Foot Clockwise Unloading Type
(Normal) Side Port R(AC DC Rectified)
Mtg.
A56 R100,R200
32
(56.2 cm3/rev)
A70 AC
A100,A120 60
(70.0 cm3/rev) Viewed from
F: 03: A200,A240
Shaft End
Flange Mtg. Pressure
A90 S: DC 2
Compensator 60 Refer to
(91.0 cm3/rev) R: Side Port D12,D24
L: 1 with D48
Foot Mtg. Clockwise Unloading Type
A145 (Normal) R(AC DC Rectified)
60
(145 cm3/rev) R100,R200
1. Available to supply pump with anti-clockwise rotation. Consult 2. Design Standards: None ........... Japanese Standard "JIS"
Yuken for details. 80 ............... European Design Standard
950 ............ N. American Design Standard
Large)
2
Output Flow
Current i 2
Input
M
O
A16/A22/A37/A56
(Small
Pressure
(Small Input Large) 1
Current i1
2
M
O
A70/A90/A145
A70 -F R 04 C S -60 *
Direction of Pressure Adj. Range Design
Series Number Mounting Control Type Port Position Design Std.
Rotation MPa (PSI) Number
A70
Viewed from 60
(70.0 cm3/rev)
F: Shaft End 04:
A90 Flange Mtg. Proportional C: 1.5 - 16 (220 - 2320) S:
Electro-Hydraulic 60 Refer to 2
(91.0 cm3/rev) H: 1.5 - 21 (220 - 3050) Side Port
L: Load Sensing
Foot Mtg. R: Type
A145 Clockwise 1
60
(145 cm3/rev)
1. Available to supply pump with anti-clockwise rotation. Consult 2. Design Standards: None ........... Japanese Standard "JIS"
Yuken for details. 80 ............... European Design Standard
Consult Yuken when “N. American Design Standard” is required.
"A" Series
1
Threaded Connection Socket Welding Butt Welding
Pump Model Name of
Numbers Port Japanese European Japanese Standard Japanese Standard
Standard Design "JIS" & "JIS" &
European Design European Design
"JIS" Standard Standard Standard
A16-*-R-04 Suction F5-06-A-10 F5-06-A-1080 F5-06-B-10 F5-06-C-10
A22-*-R-04 Discharge 2 2 2 2
1. In case of using socket welding flanges, there is a case where the operating pressure should be set lower than the normal because of strength of the
flanges. Therefore, please pay cautious attension to the operating pressure when the socket welding flanges are used.
2. Discharge port for pump model "A16" and "A22" is available only the threaded connections.
Detail of the pipe flange kits are shown on page 824.
Instructions
Bleeding Air
In order to get steadily controlled pressure and flow, bleed air by loosening the air vent screw and fill solenoid armature
with operating oil.
Manual Adjustment Screws
Manual adjustment screws may be used for initial running adjustment or in case of electrical failures in order to adjust
pressure and flow temporarily. In case of normal use, put the manual adjustment screws back in their preset positions.
Position of Cable Departure
Position of cable departure can be changed. For details, refer to EDG-01 valve on page 672.
Connection of Surge Cut-off Valve to "A" Series Pump (For A16 to A56 Type)
If using surge cut-off valve (SF1105-A-10), connect between pilot port "PP" of this pump and port "PP" of surge cut-
off valve as pilot piping (refer to drawing below).
Inside diameter of pipe should be more than 8 mm(.32 in.).
Consult Yuken of detail of surge cut-off valve.
i1
"PP"
i2
M
O
Shaft Speed Range Max. 1800 1800 1800 1800 1800 1800 1800
r/min Min. 600 600 600 600 600 600 600
Flow Adj. L/min 1 - 28.4 1 - 40 1 - 66 1 - 101 1 - 126 1 - 163 2 - 261
Range (U.S. GPM) (.26 - 7.5) (.26 - 10.6) (.26 - 17.4) (.26 - 26.7) (.26 - 33.3) (.26 - 43.1) (.53 - 69.0)
Min Pres. Required MPa 1.5 1.5 1.5 2.0 1.0 1.0 1.0
for Flow Adj. (PSI) (220) (220) (220) (290) (145) (145) (145)
Differential Pres.
MPa 0.37 0.22
(Discharge Pres.
(PSI) (55) (30)
Flow -Load Pres.)
Control
Step Response 5
ms 70 80 120 125 100 120 210
(0 Max. Flow)
4
Hysteresis 3% or less
Rated Current mA 900 700 740 790 820 920 920
Coil Resistance
10
[20°C (68°F)]
Pres. Adj. Range MPa (PSI) Refer to Model Number Designation
Step t1 5
80 80 50 55 150 150 160
Response 5
ms t2 140 90 80 80 80 120 180
4
Pres. Hysteresis 2% or less
Control
(Pres. Adj. Range) C: 860 C: 873 C: 875
Rated Current mA
B: 770, C:880, H:790 H: 765 H: 765 H: 755
Coil Resistance
[20°C (68°F)] Ω 10
3
Applicable Amplifier Model AME-D2-1010-*-10
32 32 38 45 72.5 88.5 109.5
Flange Mtg.
Approx. Mass (70.6) (70.6) (83.8) (99.2) (160) (195) (241)
kg
(lbs.) 34.2 34.2 43.2 49.3 84.5 109 134.5
Foot Mtg.
(75.4) (75.4) (95.3) (109) (186) (240) (297)
1. Whenever setting pressure, make sure the full cut-off pressure never Pres. Step Response
exceeds the maximum intermittent pressure. Model Loading Volume
t1 t2
2. When operating the pump exceeding the rated pressure, operating
conditions are restricted. Refer to page 33 for the details. 1.5 16 MPa 16 1.5 MPa High Pressure Hose
A16, A22
(220 2320 PSI) (2320 220 PSI) 3/8" 2 m (6.6 ft)
3. For detail specifications of power amplifiers, refer to page 780.
4. The figure mentioned in the above table are those obtained using 2.0 16 MPa 16 2.0 MPa High Pressure Hose
A37, A56
(290 2320 PSI) (2320 290 PSI) 3/4" 2 m (6.6 ft)
Yuken's amplifier.
5. Step response depends on circuit and operating conditions. Data A70, A90 3.0 16 MPa 16 3.0 MPa High Pressure Hose
shown in the table above is an example based on the condition right. A145 (435 2320 PSI) (2320 435 PSI) 1-1/4" 2 m (6.6 ft)
"A" Series
A16/A22/A37/A56 A70/A90/A145
PSI MPa
PSI MPa 3500 24
3000 21 3000
20 20
Full Cut-off Pressure
Output Flow
6
24 20
6 4
Output Flow
10
2
4 16 0
0
0 200 400 600 800
8 Input Current mA
2
A56
0
0 U.S.GPM L /min
0 200 400 600 800 1000 30 N=1800 r/min
110
Input Current mA 25
100
Output Flow
20 80
A37 15 60
10 40
U.S.GPM L /min N=1800 r/min
18 70 5 20
0
16 60 0
0 200 400 600 800 900
14
50 Input Current mA
12
Output Flow
10 40 A70
8 30 U.S.GPM L /min N=1800 r/min
6 35 140
20
4 30 120
Output Flow
10
2 80
0 20
0
0 200 400 600 800 40
10
Input Current mA
0 0
0 200 400 600 800 1000
Input Current mA
A90
U.S.GPM L /min N=1800 r/min A145
200
50 U.S.GPM L /min N=1800 r/min
75 280
160 70
40
240
Output Flow
120 60
30
200
50
Output Flow
20 80
160
40
10 40 120
30
0
0 20 80
0 200 400 600 800 1000
Input Current mA 10 40
0
0
0 200 400 600 800 1000
Input Current mA
4.79(.1886)
(6.00)
152.5
4.76(.1874)
X
(10.06)
(3.78)
255.5
96
(2.26)
57.5
(.47)
(.71)
12
18
82.50(3.2480) Dia.
Dia.
21.24(.836)
21.08(.830)
R12
19.05(.7500) 95(3.74) Dia.
19.02(.7488)
82.55(3.2500)
12 (R.47)
(.47) 106
172 (4.17)
(6.77) 130
Pressure Gauge Connection Surface of Suction Port (5.12)
for Pump Discharge Pressure 187 188
"D" Thd (7.36) (7.40)
262
(10.31) Pilot Port "PP"
152.2 "D" Thd. 2
Surface of Discharge Port Cable Departure
(5.99)
Tank Port (For Flow Control)
Air Vent "F" Thd. 70
3 (.12) Hex. Soc. (2.76)
Manual Pressure Adj. Screw
3 (.12) Hex. Soc. Manual Pressure Adj. Screw
3(.12) Hex. Soc.
INC.
Safety Valve Pressure Adj. Screw 41 INC.
(1.61)
17(.67) Hex.
(4.06)
103
(2.26)
INC.
57.5
(1.89)
48
(1.874)
47.6
22.2(.874) 56
(2.20) Discharge Port
M10 Thd. 17(.67) Deep 32.5 85 "E" Thd.
4 Places (1.28) (3.35)
See 3 94 190.5
(3.70) (7.50)
View Arrow X
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd.
1
A16/A22-F-R-04-*-K-32 Rc 3/8 Rc 1/4 G 3/8 Rc 1/4
A16/A22-F-R-04-*-K-3280 3/8 BSP.F 1/4 BSP.Tr 3/8 BSP.F 1/4 BSP.F
"A" Series
Air Vent 3(.12) Hex. Soc.
3 Places
Air Vent 3(.12) Hex. Soc. 308.5 59
3 Places. (12.15) (2.32) Cable Departure 1
296.5 9.5 (For Pres. Control)
(11.67) (.37)
Manual Flow Adj. Screw
110.5 Filling Port
3(.12) Hex. Soc.
(4.35) [22(.87) Hex. Head Plug Furnished]
INC.
77
77.3 Safety Valve
(3.03) Pressure Adj. Screw
30(1.18) (3.04)
Drain Port 3(.12) Hex. Soc.
"C" Thd. INC.
(7.30)
6.38(.2512)
185.5
(5.80)
147.2
32(1.26)
(5.20)
6.35(.2500)
132
(4.13)
X
(10.85)
105
275.5
(.55)
14
(.28)
(.98)
7
25
101.55(3.9980) Dia.
22.20(.8740) Dia.
25.01(.985)
24.85(.978)
120(4.72) Dia. R14
12
101.60(4.0000)
Pressure Gauge
22.23(.8752)
(R .55)
Connection for Pump (.47) 146
Discharge Pressure 195 (5.75)
"D" Thd (7.68) 174
Surface of Suction Port (6.85)
228
(8.98) 202
282 (7.95)
(11.10)
Surface of Discharge Port
100.5 115.5
(3.96) (4.55)
27
Pilot Port "PP" (1.06) Cable Departure 1 1. Cable Applicable:
"D" Thd. (For Flow Control) Outside Dia......8-10 mm (.31-.39 IN.)
Conductor Area......Not Exceeding 1.5 mm2 (.0023 Sq. IN.)
(3.35)
85
(1.874)
58.7
47.6
Discharge Port
A37-F-R-04-*-K-3280 1/2 BSP.F 1/4 BSP.Tr
Suction Port 20(.79) Dia.
32(1.26) Dia. 30.2 22.2 M10 Thd. 19(.75) Deep
M10 Thd. 19(.75) Deep (1.189) (.874) 4 Places
4 Places 36 42
(1.42) (1.65)
83
(3.27)
View Arrow X
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg. : A37-L-R-04-*-K-32/3280
14(.55) Dia. Through
28(1.10) Dia. Spotface
4 Places
(4.02)
(.59)
(.55)
102
15
14
(.12)
3
60 74 120
(2.362) (2.91) (4.72)
115 39 95 95
(4.53) (1.54) (3.740) (3.740)
230
(9.06)
For other dimensions, refer to "Flange Mtg.".
(5.80)
147.2
7.94(.3126)
X
(11.16)
283.5
(.28)
(3.54)
7
90
(.55)
(.98)
14
25
31.70(1.2480) Dia.
101.55(3.9980) Dia.
35.32(1.931)
35.14(1.383)
R14
31.75(1.2500)
101.60(4.0000)
120(4.72) Dia. (R.55)
Pressure Gauge Connection 12 146
for Pump Discharge Pressure (.47) (5.75)
"D" Thd 207 174
(8.15) (6.85)
Surface of Suction Port 232
240 (9.13)
(9.45)
294
(11.57)
Surface of Discharge Port
100 116
(3.94) (4.57) Cable Departure 1
Pilot Port "PP" 27 (For Flow Control)
"D" Thd. (1.06)
1. Cable Applicable:
Outside Dia......8-10 mm (.31-.39 IN.)
Conductor Area......Not Exceeding 1.5 mm2 (.0023 Sq. IN.)
2. Use either port of two drain ports at your option.
(3.70)
94
(1.874)
58.7
47.6
View Arrow X
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg. : A56-L-R-04-*-K-32/3280
14(.55) Dia. Through
28(1.10) Dia. Spotface
4 Places
(4.02)
(.55)
(.59)
102
14
15
(.12)
3
60 77 120
(2.362)(3.03) (4.72)
115 42 95 95
(4.53) (1.65) (3.740) (3.740)
230
(9.06)
For other dimensions, refer to "Flange Mtg.".
"A" Series
Drain Port (Both Sides) 196.5
(13.56) "C" Thd. Safety Valve INC.
Air Vent (7.74)
227.5 Pilot Port Pressure Adj. Screw
3 (.12) Hex. Soc. 169
(8.96) "D" Thd. 3 (.12) Hex. Soc.
3 Places (6.65)
196.5 62 Secondary Pressure Surface of Suction Port
Manual Flow INC. 140 95
Adj. Screw (7.74) (2.44) Gauge Connection (5.51) (3.74)
3 (.12) Hex. Soc. 191.5 for Pump Discharge 104.3
(7.54) Pressure
Air Vent "D" Thd. (4.11)
137 19.5
Dia.
3 (.12) Hex. Soc. (5.39) (.77) 73 73
3 Places
Dia.
127.00 (5.0000)
126.95 (4.9980)
3 65 9.5 (2.87) (2.87)
Cable Departure
(2.56) (.37)
31.75 (1.2500)
31.70 (1.2480)
(For Flow Control)
35.32 (1.391)
35.14 (1.383)
40 7.97 (.3138)
Tank Port 7.94 (.3126)
(7.74)
(1.57)
196.5
137(5.39)
"E" Thd.
120(4.72)
14(.55)
(3.54)
(3.27)
90
83
180(7.09)
(4.504)
18(.71)
114.4
(1.97)
14(.55)
50
(4.65)
(1.189)
118
30.2
Suction Port
1. Use either port of two drain ports at your option. Keep the remaining 38 (1.50) Dia.
port plugged.
(2.752)
69.9
2. Case drain port is available for use when draining hydraulic fluid
from pump casing.
M12 Thd. 19(.75) Deep
3. Cable Applicable: 4 Places
Outside Dia......8-10 mm (.31-.39 IN.)
Conductor Area......Not Exceeding 1.5 mm2 (.0023 Sq. IN.)
35.7
(1.406)
246.5
Model Numbers "C" Thd. "D" Thd. "E" Thd. (9.70)
Case Drain Port 2
A70-FR04*S-60 Rc 3/4 Rc 1/4 Rc 3/8 5 (.20) Hex. Soc.
A70-FR04*S-6080 3/4 BSP.F 1/4 BSP. Tr 3/8 BSP. F View Arrow X
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg.: A70-LR04*S-60/6080
42.5
(1.67)
(5.00) Dia.
(5.12)
(.94)
130
24
(.12)
3
(1.02)
125 77 171
26
(8.11)
9.56 (.3764)
206
(1.189)
30.2
9.53 (.3752)
(5.39)
(4.72)
137
(4.45)
120
113
(3.27)
83
(6.362)
X
161.6
(1.97)
50
(5.00)
127
Tank Port
38.05(1.4980) Dia.
152.35(5.9980) Dia.
"E" Thd.
42.36(1.668)
42.18(1.661)
Primary Pressure
38.10(1.5000)
152.40(6.0000)
1. Use either port of two drain ports at your option. Keep the remaining
port plugged.
(3.063)
77.8
2. Case drain port is available for use when draining hydraulic fluid
from pump casing.
3. Cable Applicable:
Outside Dia......8-10 mm (.31-.39 IN.) M12 Thd. 19(.75) Deep
Conductor Area......Not Exceeding 1.5 mm2 (.0023 Sq. IN.) 4 Places
42.9
(1.689)
Model Numbers "C" Thd. "D" Thd. "E" Thd. 270
(10.63)
A90-FR04*S-60 Rc 3/4 Rc 1/4 Rc 3/8
A90-FR04*S-6080 3/4 BSP.F 1/4 BSP. Tr 3/8 BSP. F View Arrow X
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg.: A90-LR04*S-60/6080
(.12)
3
"A" Series
Manual Pressure 400 Drain Port (Both Sides) Air Vent
Adj. Screw (15.75) "C" Thd. 3 (.12) Hex. Soc. 216.5
3 (.12) Hex. Soc. 3 Places (8.52)
280.5 112
(11.04) 189
(4.41) (7.44)
INC. Manual Flow Adj. Screw
249.5 23
3 (.12) Hex. Soc. 160 112 Surface of Suction Port
(9.82) (.91)
INC. (6.30) (4.41)
Air Vent 225 72 72
3 (.12) Hex. Soc. (8.86) Pilot Port "D" Thd. Safety Valve
13 (2.83) (2.83) Pressure Adj. Screw
3 Places 168 Secondary Pressure Gauge 85.3 3(.12) Hex. Soc.
3
(6.61) (.51) Connection for Pump
Cable Departure (3.36)
89 Discharge Pressure INC.
(For Flow Control) (3.50) "D" Thd. 11.14 (.4386)
Tank Port 70 11.11 (.4374)
"E" Thd.
(8.19)
(2.76)
208
(1.189)
(5.39)
(4.72)
137
30.2
(4.33)
120
(3.27)
110
83
(9.000)
X
228.6
(1.97)
50
(5.55)
141
Primary Pressure
Dia.
152.35(5.9980) Dia.
49.39(1.944)
49.21(1.937)
152.40(6.0000)
Suction Port
48(1.89) Dia.
1. Use either port of the two drain ports at your option. Keep the remaining
port plugged.
(3.063)
77.8
2. Case drain ports are available for use when draining hydraulic fluid
from pump casing.
3. Cable Applicable: M12 Thd. 19(.75) Deep
Outside Dia......8-10 mm (.31-.39 IN.) 4 Places
Conductor Area......Not Exceeding 1.5 mm2 (.0023 Sq. IN.) 42.9
(1.689)
299.5
Model Numbers "C" Thd. "D" Thd. "E" Thd. (11.79)
A145-FR04*S-60 Rc 3/4 Rc 1/4 Rc 3/8
A145-FR04*S-6080 3/4 BSP.F 1/4 BSP. Tr 3/8 BSP. F View Arrow X
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg.: A145-LR04*S-60/6080
22(.87) Dia. Through
43(1.69) Dia. Spotface
4 Places
(7.37)
187.3
(.12)
3
29(1.14)
30(1.18)
L)
Pressure Control
Sensor Valve
Input Voltage
Output Flow
1 2
(S
Pressure
Control (S Input Voltage L)
Piston
Graphic Symbols
A16/A22/A37/A56 A70/A90/A145
A145
60 60
(145.0 cm3/rev)
1. Available to supply pump with anti-clockwise rotation. Consult Yuken for details.
2. These pumps, except A16 and A22 types, can be connected to outboard pumps.
- A37/A56 type (outboard pump connection symbol: None): spigot diameter: 82.55 mm (3.250 in.) (A16, A22, and PV2R1).
- A70/A90/A145 type (outboard pump connection symbol: "A"): spigot diameter:82.55 mm (3.250 in.) (A16, A22, and PV2R1).
- A70/A90/A145 type (outboard pump connection symbol: "B"): spigot diameter:101.6 mm (4.000 in.)(A37 and PV2R2).
3. Amplifier Compensation Number may differ according to the main machine conditions. Consult Yuken for detail.
4. Design Standards: None ........... Japanese Standard "JIS"
80 ............... European Design Standard
Consult Yuken when “N. American Design Standard” is required.
"A" Series
2 16 16 16 16 25 25 25
Rated
(2320) (2320) (2320) (2320) (3630) (3630) (3630)
Operating Pressure
MPa (PSI) 1 21 16 21 21 28 28 28
Intermittent
(3050) (2320) (3050) (3050) (4060) (4060) (4060)
Shaft Speed Range r/min 600 - 1800
3 L/min 28.4 40.0 66.4 101.0 126.0 163.0 261.0
Max. Flow
(U.S. GPM) (7.5) (10.6) (17.5) (26.7) (33.3) (43.1) (69.0)
Instructions
Input Signal
The pump is on unload condition when the pump is operated without input signal voltage.
Electric Source
Always turn off electric source whenever the connector for swash plate tilt angle sensor is removed.
Compensation of Pump Maximum Regulated Flow at Frequency
If the same maximum flow is required at 50 Hz or 60 Hz, connect short plug in the amplifier to 60 Hz at the place where
supplied frequency is 60 Hz. At this condition, maximum flow comes to the same value at 50 Hz.
If short plug is used at 60 Hz without making the change, maximum flow increased in proportion to frequency.
Painting on Amp. Box and Solenoiod
To maintain suitable radiation effect, the amp. Box and the solenoid of the control valve should not be painted.
"D2" Dia.
SK1106- -56-60-1002
(2842 – 3045)
– 14.7
SK1106- -70-60-10
( – 2132)
Involute-serration 14.7 – 19.6
SK1106- -70-60-1001
(2132 – 2842)
A70-*R04E *-60-60
Dimensions Serration Size 19.6 – 22.6
mm (in.) SK1106- -70-60-1002
Outboard Pump Part Number of Nominal Dia. (2842 – 3277)
Connection Symbol Coupling Ass'y No. of Teeth 22.6 –
"D1" "D2" Mojule SK1106- -70-60-1003
(3277 – )
A37/A56 None 27 19.5 – 14.7
098-PK412588-6 18.75 24 0.75 SK1106- -91-60-10
"A" (1.06) (.77) ( – 2132)
14.7 – 19.6
A70/A90/A145 36 26 SK1106- -91-60-1001
"B" 098-PK412623-1 25 24 1 (2132 – 2842)
(1.42) (1.02) A90-*R04E *-60-60 19.6 – 22.6
SK1106- -91-60-1002
(2842 – 3277)
Selecting an Outboard Pump Type 22.6 –
SK1106- -91-60-1003
The maximum torque of outboard pumps is limited by shaft (3277 – )
and coupling assembly strength. When determining the – 14.7
SK1106- -145-60-10
outboard pump type, the value of the displacement times the ( – 2132)
pressure for a particular pump should not exceed the value SK1106- -145-60-1001
14.7 – 19.6
shown in the table below. (2132 – 2842)
A145-*R04E *-60-60 19.6 – 22.6
SK1106- -145-60-1002
Outboard Pump (2842 – 3277)
Pump Inboard Pump and q2 P2 22.6 –
Model Outboard Pump SK1106- -145-60-1003
Outboard pump connection symbol (3277 – )
No. (q1 P1) (q2 P2)
"None"/"A" "B" Note 1. The symbol " ", shown with pump and amplifier model numbers,
A37 900(7963) and less is the control pressure at input signal of 5 V.
2. Cable for pump-amplifier connection is not included. See Page 85
A56 1742(15413) and less
for details on ordering cables.
A70 2408(21305) and less 519(4592) and less 935(8272) and less
A90 4348(38470) and less 977(8644) and less
A145 4739(41930) and less 951(8414) and less
"A" Series
8 30
1800 r/min
100 1800 r/min
1500 r/min 25
24
6 1500 r/min
Output Flow
80
Output Flow
20
4 16 15 60
10 40
2 8
5 20
0 0
0 0
0 1 2 3 4 5 0 1 2 3 4 5
Input Signal V DC Input Signal V DC
A22 A70
U.S.GPM L /min U.S.GPM L /min
12 45 40 150
40 1800 r/min
10 125 1800 r/min
1500 r/min 30
1500 r/min
Output Flow
8 30 100
Output Flow
6 20 75
20
4 50
10 10
2 25
0 0 0
0
0 1 2 3 4 5 0 1 2 3 4 5
Input Signal V DC Input Signal V DC
A90
A37 U.S.GPM L /min
45 175
L /min 1800 r/min
U.S.GPM 80 40 150
20
1500 r/min
1800 r/min 125
Output Flow
16 60 30
1500 r/min 100
Output Flow
12
40 20 75
8
50
20 10
4 25
0 0 0
0
0 1 2 3 4 5 0 1 2 3 4 5
Input Signal V DC Input Signal V DC
Note: Pump characteristics at 1800 r/min is the same as those at 1500 r/min A145
where frequency is compensated. L /min
(Refer to page 75.) U.S.GPM 280
1800 r/min
240
60
1500 r/min
Full Cut-off Pres. vs. Input Signal 50 200
Output Flow
40 160
A*-*R04E27.5M
PSI MPa 120
28 30
4000
25 20 80
A*-*R04E24.5M
10 40
Full Cut-off Pressure
3000 20 A - R04E20.6M
** 0
0
0 1 2 3 4 5
15
2000 Input Signal V DC
10 A*-*R04E15.7M
1000
5
A*-*R04E6.9M
Refer to page 37 to 43 for performance characteristics of
0 0 pressure compensator type excluding characteristics appeared
0 1 2 3 4 5 on this catalogue.
Input Signal V DC
(6.38)
162
4.79(.1886)
4.76(.1874)
(3.78)
96
Y X
12(.47)
18(.71)
(3.07)
78
82.50(3.2480) Dia.
Dia.
82.55(3.2500)
19.05(.7500)
19.02(.7488)
21.24(.836)
21.08(.830)
12 R12
(.47) (R.47) 106
(4.17)
172
(6.77) 130
(5.12)
3
Pres. Sensor Connector
2
3
Tilt Angle Sensor Connector
M10 Thd. 17(.67) Deep
(1.874)
8 Places
47.6
(1.874)
47.6
View Arrow Y
1. Install the pump so that the "Filling Port" is at the top. Model Numbers "C" Thd.
2. Do not touch the screw because it is adjusted at the time of shipment. A16/A22-FR04E*-*-42 Rc 3/8
3. For cable connection with amplifiers, see page 85. A16/A22-FR04E*-*-4280 3/8 BSP.F
4. Cable Applicable:
Outside Dia. ...... 8-10mm(.31-.39 IN.)
Conductor Area ...... Not Exceeding 1.5mm 2 (.0023 Sq. IN.)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mounting Type
Mounting bracket is common to that of pressure compensator model.
Refer to page 45 for the dimensions of mounting bracket.
Cable Departure 3
Cable Applicable:
"A" Series
Outside Dia. ...... 8-10mm(.31-.39 IN.)
Conductor Area ......
Not Exceeding 1.5mm2(.0023 Sq. IN.)
274.5
(10.81)
251.5
(9.90) Filling Port 1
224.5 [22(.87) Hex. Head Plug Furnished]
(8.84)
166.5 Drain Port "C" Thd. 151.5 146.5
(6.56) (5.96) (5.77)
77 62 Surface of 86 86 Surface of
(3.03) (2.44) Discharge Port (3.39) (3.39) Suction Port
30 9.5
(1.18) (.37)
40(1.57)
(6.54)
Air Vent 7.97(.3138)
166
3 (.12) Hex. Soc. 7.94(.3126)
(4.13)
105
3 Places
X
(2.311)
58.7
25(.98)
14(.55)
(3.54)
90
R14
101.55(3.9980) Dia.
Dia.
1. Install the pump so that the "Filling Port" is at the top. Suction Port
32(1.26) Dia.
2. Do not touch the screw because it is adjusted at the time of shipment.
3. For cable connection with amplifiers, see page 85.
(2.311)
58.7
View Arrow X
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mounting Type
Mounting bracket is common to that of pressure compensator model.
Refer to page 46 for the dimensions of mounting bracket.
4
Cable Departure
Cable Applicable:
Outside Dia. ...... 8-10mm(.31-.39 IN.) Filling Port 1
Conductor Area ...... [22(.87) Hex. Head Plug Furnished]
Not Exceeding 1.5mm2(.0023 Sq. IN.)
287
(11.30) 2
264 Drain Port "C" Thd.
(10.39) (Both Sides)
151.5 160.5
237 Surface of (5.96) (6.32) Surface of
(9.33) Discharge Port 100 100 Suction Port
179 62 (3.94) (3.94)
(7.05) (2.44) Surface of Drain Port 41 49 Surface of Drain Port
50.5 9.5 (1.61) (1.93)
(1.99) (.37)
43.5
(1.71)
40
(1.57)
(7.52)
Air Vent
191
3 (.12) Hex. Soc. 7.97(.3128)
3 Places 7.94(.3126)
R14
(3.54)
(R.55)
90
X
(2.311)
58.7
25(.98)
14(.55)
(3.86)
98
31.70(1.2480) Dia.
101.55(3.9980) Dia.
Discharge Port
31.75(1.2500)
101.60(4.0000)
32 (1.26) Dia.
35.32(1.391)
35.14(1.383)
30.2 12 146
M10 Thd. (1.189) (.47) (5.75)
19(.75) Deep 191
4 Places 174 120(4.72) Dia.
(7.52) (6.85)
265
(10.43)
Suction Port
35(1.38) Dia.
(2.311)
58.7
DIMENSIONS IN
MILLIMETRES (INCHES)
"A" Series
Outside Dia. ...... 8-10mm(.31-.39 IN.)
Conductor Area ......Not Exceeding 1.5mm2(.0023 Sq. IN.)
333.5
(13.13)
307 2
(12.09) Drain Port "C" Thd. 116.5 155
249 (Both Sides) (4.59) (6.10)
(9.80) 62 Surface of Discharge Port 95 95 Surface of Suction Port
(2.44) (3.74) (3.74)
65 19.5(.77) Surface of Drain Port 73 73 Surface of Drain Port
(2.56) (2.87) (2.87)
9.5(.37)
40(1.57) 7.97(.3138)
(8.17)
207.5
Air Vent 7.94(.3126)
3 (.12) Hex. Soc.
3 Places
(3.54)
52.4(2.063)
90
18(.71)
(7.09)
180
Y
(4.65)
118
35(1.38) Dia. Spotface
31.70(1.2480) Dia.
126.95(4.9980) Dia.
127.00(.50000)
35.32(1.391)
35.14(1.383)
16
M10 Thd. (.63) 181
26.2
17(.67) Deep
(1.031) 18 (7.126)
4 Places (.71) 211
246.5 (8.31)
(9.70)
305.5
5 (12.03)
Filling Port 1
[22(.87) Hex. Head Plug Furnished]
4
Tilt Angle Sensor Connector
Eye Bolt
M10 4
Pres. Sensor Connector
3 3
Suction Port
38(1.50) Dia.
(2.752)
69.9
View Arrow Y
Hex. Hd. Screw
Plain Washer
End Cover
35.7 Seal Cover
(1.406) M12 Thd. 19(.75) Deep
246.5 4 Places
(9.70)
1. Install the pump so that the "Filling Port" is at the top. Case Drain Port
2. Use either port of two drain ports at your option. 5 (.20) Hex. Soc.
Keep the remaining port plugged.
View Arrow X
3. Do not touch the screw because it is adjusted at the time of shipment.
4. For cable connection with amplifiers, see page 85.
5. If you do not use the special sequence valve, plug the port (FP-SC-1/32).
A70-FR04E**-60-60 Rc 3/4
A70-FR04E**-60-6080 3/4 BSP.F
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mounting Type
Mounting bracket is common to that of pressure compensator model.
Refer to page 48 for the dimensions of mounting bracket.
4
Cable Departure
Cable Applicable:
Outside Dia. ...... 8-10mm(.31-.39 IN.)
Conductor Area ......Not Exceeding 1.5mm2(.0023 Sq. IN.)
347
(13.66) 2 117.5 155
320 Drain Port "C" Thd. Surface of Discharge Port (4.63) (6.10) Surface of Suction Port
(12.60) (Both Sides)
262 95 105 105
(10.31) (3.74) (4.13) (4.13)
119.5 23(.91) Surface of Drain Port 68 68 Surface of Drain Port
(4.70) (2.68) (2.68)
13(.51)
(8.54)
3 (.12) Hex. Soc.
217
9.56(.3764)
3 Places 9.53(.3752)
(4.45)
113
3 X
(6.362)
(2.311)
161.6
58.7
(5.00)
127
Dia.
152.35(5.9980) Dia.
Discharge Port
32 (1.26) Dia. 21.5(.85) Dia. Through
38.10(1.5000)
38.05(1.4980)
42.36(1.668)
42.18(1.661)
152.40(6.0000)
22 R22
M10 Thd. 19(.75) Deep 30.2 39(1.54) Dia. Spotface 161.6
(.87) (R.87)
4 Places (1.189) (From Rear) (6.362)
23 4 Places
(.91)
270
(10.63)
324
(12.76)
5
Case Drain Port
5 (.20) Hex. Soc.
4
Tilt Angle Sensor Connector
Eye Bolt 4
Pres. Sensor Connector
1 M10
Filling Port
[27(1.06) Hex. Head Plug Furnished]
Suction Port
1. Install the pump so that the "Filling Port" is at the top. 48(1.89) Dia.
2. Use either port of two drain ports at your option. (3.063)
Keep the remaining ports plugged.
77.8
DIMENSIONS IN
MILLIMETRES (INCHES)
4
Cable Departure
"A" Series
Cable Applicable:
Outside Dia. ...... 8-10mm(.31-.39 IN.)
Conductor Area ...... Not Exceeding 1.5mm2(.0023 Sq. IN.)
358.5 112
(14.11) (4.41) Drain Port 2
331.5 23 "C" Thd.
(13.05) (.91) (Both Sides) 169.5
273.5 (6.67)
(10.77) Surface of Discharge Port 112 112 Surface of Suction Port
89 (4.41) (4.41)
(3.50) Surface of Drain Port 72 72 Surface of Drain Port
59 13 (2.83) (2.83)
(2.32) (.51) 11.14(.4386)
11.11(.4374)
70
Air Vent (2.76)
(8.62)
3 (.12) Hex. Soc.
219
3 Places 5 X
(4.33)
110
(9.000)
(2.311)
228.6
58.7
(5.55)
141
Discharge Port
152.35(5.9980) Dia.
Dia.
32 (1.26) Dia.
44.45(1.7500)
152.40(6.0000)
44.40(1.7480)
M10 Thd.
19(.75) Deep 24 39(1.54) Dia. Spotface R22
30.2 228.6
4 Places (From Rear) (R.87)
(1.189) (.94) (9.000)
4 Places
26 273
(1.02) (10.75)
299.5
(11.79)
357.5
Case Drain Port
(14.07)
5 (.20) Hex. Soc.
Suction Port
1. Install the pump so that the "Filling Port" is at the top. 48(1.89) Dia.
2. Use either port of two drain ports at your option.
(3.063)
77.8
DIMENSIONS IN
MILLIMETRES (INCHES)
Specifications
Model No.
SK1106- -*-*-10**
Description
Applicable Coil Resistance 10 Ω [at 20 °C (68 °F)]
Input Impedance 10 kΩ (PIN, QIN)
Power Supply 24 V DC (21 - 28 V Included Ripple)
Power Input (Max.) 30 W
Input Signal Max. Flow/5V (QIN), Specified Pres./5V (PIN)
Output Signal for Sensor Monitor 5V/Max. Flow (SMQ), 5V/Specified Pres. (SMP)
Ambient Temperature 0 - 50 °C (32 - 122 °F)
Approx. Mass 450 g (1.0 lbs.)
15
CN1
Solenoid POWER
1 2
/ POWER SUPPLY
CN2
Fuse
FUSE
FUSE
(5A)
(6.50)
(5.51)
165
140
1 2 3 4 5 1 2 3 4
SK1106- - - -10
AMP. MFG NO.
/ I/O SIGNAL
PUMP MFG NO.
Signal
92
Detail of Connector (3.62)
100
Connector Name of Signal (3.94)
CN1 1
Output to pilot valve solenoid
Solenoid 2
CN2 1 0 [V] (0V )
Power 2 +24 [V] (24V)
Supply 3 0 [V]
1 +5 [V]
CN3 Power Supply for Sensor
2 0 [V]
Pres.
(1.89)
Sensor
4 0 [V]
1 +8 [V]
Power Supply for Sensor N-SK 1106-10 ****-07
CN4 2 0 [V]
Tilt
3 Input Signal - Sensor
Angle
Sensor 4 0 [V]
5
1 Input Signal - Flow (Qin)
2 Input Signal - Common (COM)
CN5
Input/ 3 Input Signal - Pres. (Pin) DIMENSIONS IN
Output 4 Output Signal - Sensor Monitor P (SMP) MILLIMETRES (INCHES)
Signal
5 Output Signal - Sensor Monitor Q(SMQ)
6 0 [V]
"A" Series
Proportional
Pilot Valve
"A" Series Piston Pump
Pressure
Sensor
1
Cable Ass'y
1 : For Solenoid
2 : For Power Supply
Colour of Lead Wire 1 3 : For Pressure Sensor
4 3 4 : For Tilt Angle Sensor
Red......Power Supply, +24V DC
White...Power Supply, 0V 5 : For Signal
Shield...Ground
1 2 3 4 5 6 1 2 3 4 5 1 2 3 4 1 2 3 1 2
2
Amplifier
Sensor
Pres.
FUSE
Supply
Power
Solenoid
Signal
Sensor
Tilt Angle
(5A)
CN5
CN4
CN3
CN2
CN1
Model : SK1106-*-*-*-11**
POWER
1. Cable assemblies are available. When ordering, specify the cable ass'y model numbers from the table below.
L)
Proportional Solenoid
Input Voltage
Pressure
Output Flow
Sensor Control
Valve
1 2
(S
Pressure
(S Input Voltage L)
Control
Piston 1. Unloading pressure when input
signal is 0 V.
2. Safety valve setting pressure
Safety valve
"A" Series
2 16 16 16 16 25 25 25
Rated
(2320) (2320) (2320) (2320) (3625) (3625) (3625)
Operating Pressure
MPa (PSI) 1 21 16 21 21 28 28 28
Intermittent
(3050) (2320) (3050) (3050) (4060) (4060) (4060)
Shaft Speed Range r/min 600 - 1800
3 L/min 28.4 40.0 66.4 101.2 126.0 163.0 261.0
Max. Flow
(U.S. GPM) (7.5) (10.6) (17.5) (26.7) (33.3) (43.1) (69.0)
Instructions
Input Signal
The pump is on unload condition when the pump is operated without input signal voltage.
Electric Source
Always turn off electric source whenever the connector for swash plate tilt angle sensor is removed.
Compensation of Pump Maximum Regulated Flow at Frequency
If the same maximum flow is required at 50 Hz or 60 Hz, connect short plug in the amplifier to 60 Hz at the place where
supplied frequency is 60 Hz. At this condition, maximum flow comes to the same value at 50 Hz.
If short plug is used at 60 Hz without making the change, maximum flow increased in proportion to frequency.
Painting on Amp. Box and Solenoiod
To maintain suitable radiation effect, the amp. box and the solenoid of the control valve should not be painted.
A16 A56
L / min L / min
U.S.GPM 32 U.S.GPM 120
8 30
1800 r/min
100 1800 r/min
24 1500 r/min 25
Output Flow
6
Output Flow
80 1500 r/min
20
4 16 15 60
10 40
2 8
5 20
0 0 0 0
0 1 2 3 4 5 0 1 2 3 4 5
Input Signal V DC Input Signal V DC
A22 A70
U.S.GPM L / min U.S.GPM L / min
12 45 40 150
40 1800 r/min
10 125 1800 r/min
30
Output Flow
1500 r/min
Output Flow
6 20 75
20
4 50
10 10
2 25
0 0 0 0
0 1 2 3 4 5 0 1 2 3 4 5
Input Signal V DC Input Signal V DC
A90
A37 U.S.GPM L / min
45 175
L / min 1800 r/min
U.S.GPM 80 40 150
20
1500 r/min
Output Flow
100
12
40 20 75
8 50
20 10
4 25
0 0 0 0
0 1 2 3 4 5 0 1 2 3 4 5
Input Signal V DC Input Signal V DC
A145
L / min
U.S.GPM 280
70 1800 r/min
240
60
1500 r/min
200
Output Flow
50
Note: Pump characteristics at 1800 r/min is the same as those at 1500 r/min 40 160
where frequency is compensated. 30 120
(Refer to page 87.) 80
20
10 40
0 0
0 1 2 3 4 5
Input Signal V DC
**
3000 20 210 (3000) A*-*R04EH210
15 A*-*R04EH140
2000 140 (2000)
A*-*R04EH20.6M
10
A*-*R04EH15.7M
1000 70 (1000) A*-*R04EH70
5
A*-*R04EH6.9M
0 0 0
0 1 2 3 4 5 0 1 2 3 4 5
Input Signal V DC Input Signal V DC
"A" Series
1
Filling Port
[ 22(.87) Hex. Head Plug Furnished]
239 44.5
(9.41) (1.75)
221 6.5
Air Vent 3(.12) Hex. Soc. (8.70) (.26)
150.5 59
(5.93) (2.32)
144 Electrical Conduit Connection 25
(5.67) G 1/2 Thd. (.98) Drain Port "C" Thd.
25
See 2 (.98)
21.24(.836)
21.08(.830)
(6.83)
173.5
Discharge Port
(5.45)
138.5
19(.75) Dia. (9.90)
251.5
(3.78)
X
96
(1.874)
47.6
19.02(.7488) Dia.
82.50(3.2480) Dia.
19.05(.7500)
82.55(3.2500)
Suction Port "D" Thd. 17(.67) Deep
22.2 8 Places 12
19(.75) Dia.
(.874) (.47)
65 172
(2.56) (6.77)
144 94
(5.67) (3.70)
4.79(.1886)
4.76(.1874)
(.43)
(.71)
11
18
DIMENSIONS IN
MILLIMETRES (INCHES)
1
Filling Port
[ 22(.87) Hex. Head Plug Furnished]
261.5 59
(10.30) (2.32)
243.5 9.5
Air Vent 3(.12) Hex. Soc. (9.59) (.37)
152.5 77
(6.00) (3.03)
146 Electrical Conduit Connection 30 Drain Port "C" Thd.
(5.75) (1.18)
G 1/2 Thd.
32
See 2 (1.26)
(6.99)
177.5
Discharge Port
(5.61)
142.5
32(1.26) Dia. (10.53)
(4.13)
267.5
105
X
(2.311)
58.7
22.20(.8740) Dia.
25.01(.985)
24.85(.978)
101.55(3.9980) Dia.
22.23(.8752)
Suction Port "D" Thd. "E" Deep
101.60(4.0000)
32(1.26) Dia. 30.2 8 Places 12
(1.189) (.47)
72 195
(2.83) (7.68)
148.5 101
(5.85) (3.98)
6.38(.2512)
6.35(.2500)
(.98)
(.55)
25
14
DIMENSIONS IN
MILLIMETRES (INCHES)
"A" Series
1
Filling Port
[ 22(.87) Hex. Head Plug Furnished]
274 62
(10.79) (2.44)
256 9.5
Air Vent 3(.12) Hex. Soc. (10.08) (.37)
152.5 50.5
(6.00) (1.99)
146 Electrical Conduit Connection 43.5
(5.75) (1.71) Drain Port 2
G 1/2 Thd. "C" Thd. (Both Sides)
3
See
40
(1.57)
(7.97)
202.5
(6.59)
167.5
Discharge Port
(11.83)
32(1.26) Dia.
300.5
(3.54)
X
90
(2.311)
58.7
35.52(1.391)
35.14(1.383)
31.70(1.2480) Dia.
101.55(3.9980) Dia.
31.75(1.2500)
Suction Port
"D" Thd. "E" Deep
101.60(4.0000)
35(1.38) Dia.
8 Places
30.2 12
(1.189) (.47)
76 207
(2.99) (8.15)
163 116
(6.42) (4.57)
Surface of Drain Port
41 49
(1.61) (1.93)
25
14
"E"
Model Numbers "C" Thd. "D" Thd. R14
mm (IN.)
(R.55)
A56-FR04EH*-*-42 Rc 3/4 M10 19 (.75) 120(4.72) Dia.
146
A56-FR04EH*-*-4290 SAE #12 7/16-14 UNC 20 (.79) (5.75)
174
(6.85)
View Arrow X
DIMENSIONS IN
MILLIMETRES (INCHES)
107.5 155
(4.23) (6.10)
314 62 Surface of Discharge Port 95 95 Surface of Suction Port
(12.36) (2.44) (3.74) (3.74)
65 19.5 Air Vent 3(.12) Hex. Soc. 89.5
(2.56) (.77) (3.52)
9.5 Surface of Drain Port 73 73 Surface of Drain Port
Drain Port 2
"C" Thd. (Both Sides) (.37) (2.87) (2.87)
Electrical Conduit Connection
G 1/2 Thd.
40
7.97(.3138)
Plug 5 (1.57)
(8.41)
213.5
(.55)
7.94(.3126)
14
(7.07)
179.5
2(.079) Hex. Soc.
(3.54)
X
90
(2.063)
(4.504)
(7.09)
114.4
52.4
180
(4.65)
(.71)
35.32(1.391)
35.14(1.383)
31.70(1.2480) Dia.
118
18
Discharge Port 126.95(4.9980) Dia.
26(1.02) Dia.
31.75(1.2500)
(2.752)
69.9
Suction Port
38(1.50) Dia.
View Arrow X
Dimensions mm (IN.)
Model Numbers "C" Thd. "D" Thd. "E" Thd.
F
A70-FR04EH**S-*-60 Rc 3/4 M12 M10 19 (.75)
A70-FR04EH**S-*-60950 SAE #12 1/2-13 UNC 3/8-16 UNC 21 (.83)
DIMENSIONS IN
MILLIMETRES (INCHES)
"A" Series
Surface of 123.7 95 107 155
Electrical Conduit Connection (4.87) (3.74) (4.21) (6.10)
119.5 23 89.5 Air Vent 3(.12) Hex. Soc.
(4.70) (.91) (3.52)
Drain Port 2 13 Surface of 68 68 Surface of
"C" Thd. (Both Sides) (.51) Drain Port (2.68) (2.68) Drain Port
63 Electrical Conduit Connection
(2.48) G 1/2 Thd.
Plug 5
(8.78)
9.56(.3764)
(7.44)
223
189
2(.079) Hex. Soc. 9.53(.3752)
(4.45)
113
X
(2.311)
(6.362)
161.6
58.7
(5.00)
127
42.36(1.668)
42.18(1.661)
38.05(1.4980) Dia.
Discharge Port
152.35(5.9980) Dia.
32(1.26) Dia. 21.5(.85) Dia. Through
38.10(1.5000)
Eye Bolt
(M10)
Amplifier Direction "R" : Filling Port 1
A90-FR04EH*R _S-*-60/60950 [27(1.06) Hex. Head Plug Furnished]
3
(3.063)
77.8
Suction Port
48(1.89) Dia.
View Arrow X
Dimensions mm (IN.)
Model Numbers "C" Thd. "D" Thd. "E" Thd.
F
A90-FR04EH**S-*-60 Rc 3/4 M12 M10 19 (.75)
A90-FR04EH**S-*-60950 SAE #12 1/2-13 UNC 7/16-14 UNC 21 (.83)
DIMENSIONS IN
MILLIMETRES (INCHES)
Plug 5
(8.86)
(7.52)
225
191
2(.079) Hex. Soc.
11.14(.4386)
(4.33)
110
11.11(.4374) X
(2.311)
(9.000)
228.6
58.7
(5.55)
49.39(1.944)
49.21(1.937)
141
Discharge Port 44.40(1.7480) Dia.
152.35(5.9980) Dia.
32(1.26) Dia.
44.45(1.7500)
Eye Bolt
(M10)
Amplifier Direction "R" : Filling Port 1
(3.063)
77.8
Suction Port
48(1.89) Dia.
View Arrow X
Dimensions mm (IN.)
Model Numbers "C" Thd. "D" Thd. "E" Thd.
F H
A145-FR04EH**S-*-60 Rc 3/4 M12 M10 19 (.75) 19 (.75)
A145-FR04EH**S-*-60950 SAE #12 1/2-13 UNC 7/16-14 UNC 21 (.83) 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
"A" Series
50/60 Hz Short Plug
60Hz
50Hz
24 V
Compensation Cartridge
FUSE
0V
ALM ALM SMQ SMP Q IN C P IN CH
C S
SPARE
FUSE
Terminal Name
P IN Input Signal, Pressure (+)
C Input Signal (COM)
Q IN Input Signal, Flow (+)
SMP Sensor Monitor Output, Pressure
SMQ Sensor Monitor Output, Tilt Angle
0V
Power Supply
24 V
ALM S Alarm Output
ALM C Alarm Output (COM)
CH Output Current Check (to COM)
Circuit Schematic
ALARM P SENSOR
SIG COM MONITOR
PRESS.
SENSOR
P IN
A
P GAIN ALARM
C
LQC
Q IN
A
CH
D CMG
OSC
DITHER
POSITION
SENSOR
FMG
24 V 0V Q SENSOR
MONITOR
Output Flow
M
O
Pressure
Specifications
Geometric Minimum Operating Pressure Shaft Speed Range Approx. Mass
MPa (PSI) Minimum r/min kg (lbs.)
Displacement Adj. Flow
Model Numbers Adj. Pres.
cm3/rev cm3/rev 2 1 Flange Foot
Rated Intermittent MPa (PSI) Max. Min.
(cu. in. /rev) (cu. in. /rev) Mtg. Mtg.
10.0 2 16 21 2.0 8.5 10.7
A10-FR07-12* 1800 600
(.610) (.122) (2320) (3050) (290) (18.7) (23.6)
15.8 4 16 21 1.2 21 23.2
A16-*-R-07-*-K-32* 1800 600
(.964) (.244) (2320) (3050) (175) (46.3) (51.2)
22.2 6 16 16 1.2 21 23.2
A22-*-R-07-*-K-32* 1800 600
(1.355) (.366) (2320) (2320) (175) (46.3) (51.2)
36.9 10 16 21 1.2 29 33.3
A37-*-R-07-*-K-32* 1800 600
(2.25) (.610) (2320) (3050) (175) (63.9) (73.4)
56.2 12 16 21 1.2 36 40.3
A56-*-R-07-*-K-32* 1800 600
(3.43) (.732) (2320) (3050) (175) (79.4) (88.9)
70.0 30 25 25 2 60.3 72.3
A70-*R07S-60* 1800 600
(4.27) (1.83) (3630) (3630) (290) (133) (159)
91.0 56 25 25 2 77.5 98
A90-*R07S-60* 1800 600
(5.55) (3.42) (3630) (3630) (290) (171) (216)
145 83 25 25 2 94 119
A145-*R07S-60* 1800 600
(8.85) (5.06) (3630) (3630) (290) (207) (262)
1. Whenever setting pressure, make sure the full cut-off pressure never exceeds the maximum intermittent pressure.
2. When operating the pump exceeding the rated pressure, operating conditions are restricted.
Refer to page 33 for the details.
"A" Series
A16 Viewed from 32
(15.8 cm3/rev) Shaft End
F: None:
A22 Flange Mtg. Axial Port
07: 32
(22.2 cm3/rev) R: Pilot Pressure
1 K: Refer to 3
Clockwise Control Type
A37 Keyed Shaft
L: (Normal) Pressure S:
32
(36.9 cm3/rev) Foot Mtg. Compensator Side Port
A56
32
(56.2 cm3/rev)
A70 -F R 07 S -60 *
Direction of Design
Series Number Mounting Control Type Port Position Design Std.
Rotation Number
A10 F: 2 Viewed from 12
(10.0 cm3/rev) Flange Mtg.
Shaft End
A70 07:
60
(70.0 cm3/rev) F: Pilot Pressure 3
R: Control Type Refer to
A90 Flange Mtg. 1 S:
Clockwise Pressure 60
(91.0 cm3/rev) L: Compensator Side Port
(Normal)
A145 Foot Mtg.
60
(145 cm3/rev)
1. Available to supply pump with anti-clockwise rotation. Consult 3. Design Standards: None ........... Japanese Standard "JIS"
Yuken for details. 80 ............... European Design Standard
950 ............ N. American Design Standard
2. When A10 pump is used as the foot Mtg., order the Mtg. Bracket kit
shown below separately. Refer to page 24 for dimensions of the Mtg.
bracket.
Performance Characteristics
For performance characteristics, refer to models of pressure compensator type on page 36 to 43.
(1.61)
4.76(.1874)
13(.51) Hex. 41
(4.21)
107
(3.62)
(2.56)
92
(6.73)
65
171
DEC.
(.43)
11
82.50(3.2480) Dia.
Dia.
2 3
Suction Port 10.5
19.05(.75000)
19.02(.74880)
82.55(3.2500)
25 25 93 (3.66) 106
RC 1/2 Thd. (.41)
21.24(.836)
21.08(.830)
Dia. (4.17)
(.98) (.98) 2 3 131
64.5 64.5 Discharge Port (5.16) 130
(2.54) (2.54) RC 1/2 Thd. 156 (5.12)
(6.14)
159.5
(6.28)
"H" Thd.
Drain Port
"F" Thd.
Plug
"D" Hex.
2 3 2 3
Suction Port Discharge Port
"E" Thd. C C "E" Thd. A
B B 159.5(6.28)
"A" Series
Fully Extended
227(8.94)
202
2 (7.95)
Pilot Port "PP"
"D" Thd. 187 44.5
(7.36) (1.75)
59 6.5 1
Filling Port
(2.32) (.26) [22(.87) Hex. Head Plug Furnished]
26.5
(1.04) Drain Port "C" Thd.
4.79(.1886)
25(.98)
4.76(.1874)
(4.29)
(3.78)
109
(3.25)
96
82.5
(2.44)
62
(7.36)
187
(.71)
(.47)
18
12
X
82.50(3.2480) Dia.
19.02(.74880) Dia.
R12
(R.47)
19.05(.75000)
82.55(3.2500)
95(3.74) Dia.
21.24(.836)
21.08(.830)
12 106
(.47) (4.17)
172 130
(6.77) (5.12)
188
Flow Adj. Screw (7.40)
5(.20) Hex. Soc.
43.5
DEC. (1.71)
2
16 18 Pilot Port "PP"
Safety Valve Pressure Adj. (.63) (.71) "E" Thd.
Screw 17(.67) Hex. Soc.
INC.
(2.56)
View Arrow X
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd.
A16/A22-F-R-07-K-32 Rc 3/8 Rc 3/8 Rc 1/4
M10
A16/A22-F-R-07-K-3280 3/8 BSP. F 3/8 BSP. F 1/4 BSP. Tr
A16/A22-F-R-07-K-32950 SAE #8 SAE #6 SAE #4 3/8-16 UNC
DIMENSIONS IN
MILLIMETRES (INCHES)
6.38(.2512)
32(1.26) 6.35(.2500)
(4.41)
(4.13)
(3.48)
112
105
88.5
(2.68)
68
(7.95)
(2.311)
202
X
58.7
(.55)
(.98)
14
25
101.55(3.9980) Dia.
Dia. R14
(R.55)
101.60(4.0000)
120(4.72) Dia.
22.23(.87520)
22.20(.87400)
86 86
(3.39) (3.39)
Surface of Suction Port Surface of Discharge Port
View Arrow X
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A37-F-R-07-S-K-32 Rc 1/2 Rc 3/8 Rc 1/4
M10 19 (.75)
A37-F-R-07-S-K-3280 1/2 BSP.F 3/8 BSP.F 1/4 BSP. Tr
A37-F-R-07-S-K-32950 SAE #10 SAE #6 SAE #4 7/16-14 UNC 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
"A" Series
Fully Extended
262.5(10.33)
237.5
2 (9.35)
Pilot Port "PP" 222.5 62
"D" Thd. (8.76) (2.44) Filling Port 1
50.5 9.5 [22(.87) Hex. Head Plug Furnished]
(1.99) (.37) 2
43.5 Drain Port "C" Thd.
(Both Sides) Surface of Drain Port
(1.71)
41 49
(1.61) (1.93)
7.97(.3138)
40(1.57) 7.94(.3126)
(5.43)
138
(3.84)
(3.54)
97.5
(3.03)
90
77
(9.29)
236
X
(2.311)
58.7
(.55)
(.98)
14
25
101.55(3.9980) Dia.
31.70(1.2480) Dia. R14
(R.55)
101.60(4.0000)
31.75(1.2500)
120(4.72)
35.32(1.391)
"F" Thd. "H" Deep 35.14(1.383)
30.2 12 Dia. 146
4 Places (Both Sides) (1.189) (.47) (5.75)
Discharge Port 30(1.18) Dia. 191 174
(Rear Side) (7.52) (6.85)
Suction Port 35(1.38) Dia. 232
(9.13)
Flow Adj. Screw
5(.20) Hex. Soc. 46.5
(1.83) 2
Pilot Port "PP"
DEC. "E" Thd.
13 21
Safety Valve Pressure Adj. (.51) (.83) 1. Install the pump so that the "Filling Port" is at the top.
Screw 5(.20) Hex. Soc. 2. Use either port of two pilot and drain ports at your option.
Keep the remaining ports plugged.
INC.
(3.15)
80
100 100
(3.94) (3.94)
Surface of Suction Port Surface of Discharge Port
View Arrow X
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A56-F-R-07-S-K-32 Rc 3/4 Rc 3/8 Rc 1/4
M10 19 (.75)
A56-F-R-07-S-K-3280 3/4 BSP.F 3/8 BSP.F 1/4 BSP. Tr
A56-F-R-07-S-K-32950 SAE #12 SAE #6 SAE #4 7/16-14 UNC 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
14(.55)
(1.57) 7.94(.3126)
(7.11)
(7.17)
180.5
182
Y
(3.54)
(.71)
90
18
(2.063)
(4.504)
(7.09)
114.4
52.4
180
(4.65)
118
35(1.38) Dia. Spotface
126.95(4.9980) Dia.
Discharge Port
31.70(1.2480) Dia.
(From Rear)
26(1.02) Dia. 2 Places
127.00(5.0000)
31.75(1.2500)
Surface of
Pilot Port "PP1"
2
Pilot Port "PP2"
316.5 "F" Thd.
(14.46)
Eye Bolt 244
M10 (9.61)
1
Safety Valve Pres. Filling Port
2 22(.87) [22(.87) Hex. Head Plug Furnished]
Pilot Port "PP1" Adj. Screw
"F" Thd. 14(.55) Hex.
(6.52)
165.5
INC.
(2.752)
69.9
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A70-FR07S-60 Rc 3/4 Rc 1/4
M12 M10 19 (.75)
A70-FR07S-6080 3/4 BSP.F 1/4 BSP. Tr
A70-FR07S-60950 SAE #12 1/2-13 UNC 3/8-16 UNC SAE #4 21 (.83)
DIMENSIONS IN
MILLIMETRES (INCHES)
2
Drain Port "C" Thd.
"A" Series
(Both Sides) Surface of Discharge Port Surface of Suction Port
95
(3.74) 105 105
119.5 23(.91) (4.13) (4.13)
(4.70) Surface of Drain Port 68 68 Surface of Drain Port
13(.51)
(2.68) (2.68)
63(2.48)
X
(7.48)
(7.50)
190.5
190
9.56(.3764)
(4.45)
Y
113
9.53(.3752)
(6.362)
(2.311)
161.6
58.7
(5.00)
127
Discharge Port
152.35(5.9980) Dia.
Dia.
32(1.26) Dia.
152.40(6.0000)
22
38.10(1.5000)
38.05(1.4980)
(6.69)
170
(.37) (.69)
(3.46)
88
(3.063)
77.8
Suction Port
48(1.89) Dia.
42.9
View Arrow X (1.689)
270 "D" Thd. "H" Deep
(10.63) 4 Places
View Arrow Y
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. H mm (IN.)
A90-FR07S-60 Rc 3/4 Rc 1/4
M12 M10 19 (.75)
A90-FR07S-6080 3/4 BSP.F 1/4 BSP. Tr
A90-FR07S-60950 SAE #12 1/2-13 UNC 7/16-14 UNC SAE #4 21 (.83)
DIMENSIONS IN
MILLIMETRES (INCHES)
2
Drain Port "C" Thd.
(Both Sides)
Surface of Discharge Port Surface of Suction Port
112 112
Fully Extended 112 (4.41) (4.41)
400.5(15.77) (4.41) Surface of Drain Port 72 72 Surface of Drain Port
89 23 (2.83) (2.83)
(3.50) (.91) 15
13 (.59)
(.51)
70
X (2.76)
(7.81)
11.14(.4386)
198.5
11.11(.4374)
(4.33)
110
Y
(9.000)
(2.311)
228.6
58.7
(5.55)
141
Discharge Port
152.35(5.9980) Dia.
44.40(1.7480) Dia.
32(1.26) Dia.
21.5(.85) Dia. Through
152.40(6.0000)
"E" Thd.
44.45(1.7500)
Surface of
Eye Bolt Pilot Port "PP1"
Safety Valve Pres. M10 2
Adj. Screw 362.5 Pilot Port "PP2"
2
24 14(.55) Hex. (14.27) "F" Thd.
Pilot Port "PP1" INC.
(.94) 290
"F" Thd. Flow Adj. Screw
(11.42)
17(.67) Hex. Filling Port 1
DEC. [27(1.06) Hex. Head Plug Furnished]
Suction Port
(6.97)
(7.56)
177
192
48(1.89) Dia.
(3.063)
77.8
View Arrow Y
1. Install the pump so that the "Filling Port" is at the top.
2. Use either port of two pilot and drain ports at your option.
Keep the remaining ports plugged.
3. Case drain port is available for use when draining hydraulic fluid
from pump casing.
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. H mm (IN.) J mm (IN.)
A145-FR07S-60 Rc 3/4 Rc 1/4
M12 M10 19 (.75) 19 (.75)
A145-FR07S-6080 3/4 BSP.F 1/4 BSP. Tr
A145-FR07S-60950 SAE #12 1/2-13 UNC 7/16-14 UNC SAE #4 21 (.83) 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
"A" Series
Performance Characteristics
Ou
tp
ut
F
lo
w
Output Flow
Input Power
Input Power
Pressure
Graphic Symbols
M M M
O O O
Specifications
Geometric Minimum 2 Operating Pres. Shaft Speed Range Approx. Mass
Displacement Adj. Flow MPa (PSI) r/min kg (lbs.)
Model Numbers
cm3/rev cm3/rev Flange Foot
(cu. in. /rev) (cu. in. /rev) Max. Max. Min.
Mtg. Mtg.
1
A16-*-R-09-*-*-K-32* 15.8 (.964) 21 (3050) 1800 600 29.0 (63.9) 31.2 (68.8)
1
A37-*-R-09-*-*-K-32* 36.9 (2.25) 21 (3050) 1800 600 37.0 (81.6) 41.3 (91.1)
1
A56-*-R-09-*-*-K-32* 56.2 (3.43) 21 (3050) 1800 600 44.0 (97.0) 48.3 (107)
A70-*R09*S-60* 70.0 (4.27) 30 (.295) 25 (3630) 1800 600 72.8 (161) 84.8 (187)
A145-*R09*S-60* 145 (8.85) 83 (5.06) 25 (3630) 1800 600 110 (243) 135 (298)
1. Maximum Operating Pressure of A16/A37/A56 varies according to Input Power Setting. See Model Number Designation for details.
2. Minimum Adjustment Flow of A70/A145 is absolutely minimum flow that can be adjusted with Flow Adjustment Screw.
A90 type pump (91 cm3/rev) is available. Ask Yuken for Details.
A70/A145
A70 -F R 09 A S -60 *
Direction of Design Design
Series Number Mounting Rotation Control Type Input Power Setting Direction of Port Number Std.
A: 15 kW E : 22 kW
A70 (20 HP) (30 HP)
B: 18.5 kW F : 30 kW 60
(70 cm3/rev) F: Flange
Viewed from (25 HP) (40 HP)
Mtg.
Shaft End 09: Constant A: 15 kW E : 37 kW
Power (20 HP) (50 HP) Refer to
Control B: 18.5 kW F : 45 kW S: Side Port
3
L: Foot Type (20 HP) (60 HP)
A145 Mtg. R: Clockwise 1
C: 22 kW G : 55 kW 60
(145 cm3/rev) (Normal) (30 HP) (75 HP)
D: 30 kW H : 75 kW
(40 HP) (100 HP)
1. Available to supply pump with anti-clockwise rotation. Consult Yuken for details.
2. Specify control pressure of A16/A37/A56 with lower than Maximum Operating Pressure depending on Input Power Setting.
Performance Maximum Operating Pressure
Characteristics MPa (PSI)
Model 1.5 kW (2 HP) 2.2 kW (3 HP) 3.7 kW (5 HP) 5.5 kW (7.5 HP) 7.5 kW (10 HP) 11 kW (15 HP) 15 kW (20 HP) 18.5 kW (25 HP) 22 kW(30 HP)
A16 10.5 (1520) 16 (2320) 21 (3050) 21 (3050)
A37 16 (2320) 21 (3050) 21 (3050) 21 (3050)
A56 10.5 (1520) 14 (2030) 17.5 (2540) 21 (3050) 21 (3050) 21 (3050) 21 (3050)
3. Design Standards: None ........... Japanese Standard "JIS"
80 ............... European Design Standard
950 ............ N. American Design Standard
A16 A70
"A" Series
U.S.GPM U.S.GPM
L/min L/min kW HP
8 30 200 40
50 50
Output Flow 5.5 kW kW HP 35
6 8
6 Input Power
Input Power 30 kW
20 5 40 150 30 40
Output Flow
Input Power
3.7 kW 6
4 25
4
Output Flow
Input Power
30 Output Flow 22 kW 30
3 4
2.2 kW 100 20
10 18.5 kW
2 2
2 15 kW
20 15 20
1
1.5 kW 30 kW
0 0 0 50 10
0 22 kW
0 3.5 7 10. 5 14 17. 5 21 MPa 10 10
(500) (1000) (1500) (2000) (2500) (3000) (PSI) 18.5 kW 5
Pressure
15 kW
0 0 0
0
0 10 20 30 MPa
A37
U.S.GPM
L/min 11 kW kW HP
60 Output Flow 12 16
15 Input Power
A145
50 10
12 7.5 kW 10 L/min kW HP
40 8 300 75 100
Output Flow
Input Power
9 U.S.GPM 37 kW 70
5.5 kW 90
30 6 8 70 45 kW
6 60 80
20 4 60 Output Flow Input Power 55 kW
4 55 kW 70
3 200 50
10 2 50
3.7 kW 60
45 kW
Output Flow
Input Power
0 0
0 0 40
0 3.5 7 10. 5 14 17. 5 21 MPa 40 50
(500) (1000) (1500) (2000) (2500) (3000) (PSI) 37 kW
Pressure 30 40
30 30 kW
100
30
20 22 kW 20
30 kW 20
10 22 kW 10
10
A56
0 0 0
U.S.GPM 0
0 10 20 30 MPa
L/min 5.5 kW 7.5 kW11 kW 15 kW 22 kW 18.5 kW kW HP
120 24 32 0 1000 2000 3000 4000 PSI
30 Input Power Pressure
100 20
25 Output Flow
24
80
Output Flow
Input Power
20
15 60 16
10
10 40
8
5 20
3.7 kW
0 0 0
0
0 3.5 7 10. 5 14 17. 5 21 MPa
(500) (1000) (1500) (2000) (2500) (3000) (PSI)
Pressure
25 4.79(.1886)
(4.37)
(3.78)
R12
111
(.98) 4.76(.1874)
96
X (R.47)
(3.07)
(.47)
(.71)
12
18
78
Dia.
Dia.
95(3.74) Dia.
82.55(3.2500)
82.50(3.2480)
19.05(.7500)
19.02(.7488)
12
21.24(.836)
21.08(.830)
(.47)
252
(9.92)
3
Pressure Adj. Screw
Fully Extended
245
(9.65)
63.5
(2.50)
Suction Port
19(.75) Dia.
(1.874)
47.6
View Arrow X
1. Detail of Discharge Port 2. Install the pump so that the "Filling Port" is at the top.
[For Japanese Standard] 3. Do not touch the screw because it is adjusted at the time of shipment.
17
(.67)
0.5 2.5
(.020) (.098)
G1/2 Thd.
15°
22.6(.89) Dia.
34(1.34) Dia.
DIMENSIONS IN
MILLIMETRES (INCHES)
"A" Series
[22(.87) Hex. Head Plug Furnished] (.37) 101 101
30 32 (3.98) (3.98)
(1.18) (1.26)
Fully Extended
(6.10)
155
6.38(.2512)
(4.13)
105
6.35(.2500)
(.28)
7
(.55)
(3.54)
(.98)
14
25
90
R14
Dia.
12 (R.55)
Dia.
101.60(4.0000)
101.55(3.9980)
(.47)
Pressure Gauge Connection
22.23(.8752)
22.20(.8740)
195 146
25.01(.985)
24.85(.978)
for Pump Discharge Pressure (7.68) (5.75)
120(4.72) Dia.
"D" Thd. 228 174
(8.98) (6.85)
282
(11.10)
Surface of Suction Port
2
Pressure Adj. Screw
Fully Extended 2
141 Input Power Setting Screw
(5.55)
Discharge Port
Suction Port
30(1.18) Dia. 20(.79) Dia.
1. Install the pump so that the "Filling Port" is at the top.
(2.311)
(1.874)
58.7
47.6
View Arrow X
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A37-F-R-09-*-K-32 Rc 1/2 Rc 1/4
M10 M10 19 (.75)
A37-F-R-09-*-K-3280 1/2 BSP.F 1/4 BSP.Tr
A37-F-R-09-*-K-32950 SAE #10 SAE #4 7/16-14 UNC 3/8-16 UNC 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg. : A37-L-R-09-*-K-32/3280/32950
14(.55) Dia. Through
28(1.10) Dia. Spotface
4 Places
(4.02)
(.59)
(.55)
102
15
14
(.12)
3
60 74 120
(2.362) (2.91) (4.72)
115 39 95 95
(4.53) (1.54) (3.740) (3.740)
230
(9.06)
For other dimensions, refer to "Flange Mtg.".
7.97(.3138)
161
7.94(.3126)
(3.54)
X
90
(.28)
7
(.98)
25
(.55)
(3.86)
14
98
Dia.
Dia.
12 R14
(R.55) 120(4.72) Dia.
101.60(4.0000)
101.55(3.9980)
(.47)
31.75(1.2500)
31.70(1.2480)
35.32(1.391)
35.14(1.383)
207 146
(8.15) (5.75)
240 174
Pressure Gauge Connection (9.45) (6.85)
for Pump Discharge Pressure 294 232
"D" Thd. (11.57) (9.13)
Surface of Suction Port
3
Pressure Adj. Screw
Fully Extended
141
3
(5.55) Input Power Setting Screw
Discharge Port
20(.79) Dia.
Suction Port
35(1.38) Dia. 1. Install the pump so that the "Filling Port" is at the top.
2. Use either port of two drain ports at your option.
(2.311)
(1.874)
58.7
47.6
View Arrow X
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A56-F-R-09-*-K-32 Rc 3/4 Rc 1/4
M10 M10 19 (.75)
A56-F-R-09-*-K-3280 3/4 BSP.F 1/4 BSP.Tr
A56-F-R-09-*-K-32950 SAE #12 SAE #4 7/16-14 UNC 3/8-16 UNC 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg. : A56-L-R-09-*-K-32/3280/32950 14(.55) Dia. Through
28(1.10) Dia. Spotface
4 Places
(4.02)
(.55)
(.59)
102
14
15
(.12)
3
60 77 120
(2.362)(3.03) (4.72)
115 42 95 95
(4.53) (1.65) (3.740) (3.740)
230
(9.06)
For other dimensions, refer to "Flange Mtg.".
Fully Extended
"A" Series
351.5 62 27(1.06) Dia. Spotface
(13.84) (2.44) (From Rear) 4 places
Drain Port 2 65 19.5 188 95 Surface of Suction Port
"C" Thd. (Both Sides) (2.56) (.77) (7.40) (3.74)
"E" Thd. 17(.67) Deep 9.5 Surface of Drain Port 73 73 Surface of Drain Port
(.37) (2.87)(2.87)
4 Places
40
(1.57) 7.97(.3138)
Y 7.94(.3126)
(7.17)
(7.11)
180.5
182
(3.54)
X
(.71)
18
90
(4.504)
(1.031)
(7.09)
114.4
26.2
180
(4.65)
118
Dia.
Dia.
(.55)
14
Discharge Port
31.75(1.2500)
31.70(1.2480)
127.00(5.0000)
126.95(4.9980)
35.32(1.391)
18(.71) Dia. 35.14(1.383)
52.4 18 114.4 35(1.38) Dia. Spotface
(2.063) (.71) (4.504) (From Rear) 2 places
212.5 134
(8.37) (5.28)
3
Input Power Setting Screw "A" 181
Input Power Setting Screw "B" 3 (7.126)
211
(8.31)
(2.752)
69.9
"D" Thd. "F" Deep
View Arrow Y 4 Places
4
Case Drain Port 35.7
5(.20) Hex. Soc. (1.406)
246.5
(9.70)
View Arrow X
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mounting Type
Mounting bracket is common to that of pressure compensator model.
Refer to page 48 for the dimensions of mounting bracket.
Drain Port 2
3
Input Power Setting Screw "A" Fully Extended "C" Thd. (Both Sides)
397 112
(15.63) (4.41) Surface of Discharge Port 214 112 Surface of Suction Port
89 23 (8.43) (4.41)
(3.50) (.91) Surface of Drain Port 72 72 Surface of Drain Port
13 (2.83)(2.83)
Discharge Port 11.14(.4386)
(.51) 11.11(.4374)
32(1.26) Dia.
70
Fully Extended
(1.189)
(2.76)
30.2
(9.69)
246
(7.81)
198.5
X
(4.33)
110
(2.24)
(9.000)
57
228.6
YUKEN
(5.55)
141
152.35(5.9980) Dia.
"E" Thd. "H" Deep
44.40(1.7480) Dia.
4 Places
152.40(6.0000)
21.5(.85) Dia. Through
44.45(1.7500)
R22
49.39(1.994)
49.21(1.937)
58.7 24 228.6
39(1.54) Dia. Spotface (R.87)
(2.311) (.94) (9.000)
(From Rear)
299.5 273
4 Places
(11.79) (10.75)
4
Case Drain Port
5(.20) Hex. Soc.
Eye Bolt
INC.
M10 Pressure Adj. Screw
Filling Port 1 17(.67) Hex.
[27(1.06) Hex. Head Plug Furnished] Flow Adj. Screw
17(.67) Hex. DEC.
Suction Port
1. Install the pump so that the "Filling Port" is at the top.
48(1.89) Dia.
2. Use either port of two drain ports at your option.
(3.063)
77.8
Keep the remaining port plugged.
3. Do not touch the screw because it is adjusted at the time of shipment.
4. Case drain port is available for use when draining hydraulic fluid from "D" Thd. "F" Deep
pump casing. 4 Places
42.9
(1.689)
299.5
(11.79)
View Arrow X
Model Numbers "C" Thd. "D" Thd. "E" Thd. F mm (IN.) H mm (IN.)
A145-FR09*S-60 Rc 3/4
M12 M10 19 (.75) 19 (.75)
A145-FR09*S-6080 3/4 BSP.F
A145-FR09*S-60950 SAE #12 1/2-13 UNC 7/16-14 UNC 21 (.83) 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mounting Type
Mounting bracket is common to that of pressure compensator model.
Refer to page 50 for the dimensions of mounting bracket.
"A" Series
Graphic Symbol
M
O
Specifications
Shaft Speed
Geometric Min. Adj. Operating Pressure Approx. Mass
Range
Displacement Flow MPa (PSI) kg (lbs.)
Model Numbers r/min
cm3/rev cm3/rev
Flange Foot
(cu.in./rev) (cu.in./rev) Rated Intermittent Max. Min.
Mtg. Mtg.
Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 35.5 37.7
A1616-*R01*01**K-32* 1800 600
Inboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) (98.3) (83.1)
Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 35.5 37.7
A1622-*R01*01**K-32* 1800 600
Inboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) (98.3) (83.1)
Outboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 35.5 37.7
A2222-*R01*01**K-32* 1800 600
Inboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) (98.3) (83.1)
Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 50 54.3
A1637-*R01*01**K-32* 1800 600
Inboard Pump 36.9 (2.25) 10 (.610) 16 (2320) 21 (3050) (110) (120)
Outboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 50 54.3
A2237-*R01*01**K-32* 1800 600
Inboard Pump 36.9 (2.25) 10 (.610) 16 (2320) 21 (3050) (110) (120)
Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 54.5 58.8
A1656-*R01*01**K-32* 1800 600
Inboard Pump 56.2 (3.43) 12 (.732) 16 (2320) 21 (3050) (120) (130)
Outboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 54.5 58.8
A2256-*R01*01**K-32* 1800 600
Inboard Pump 56.2 (3.43) 12 (.732) 16 (2320) 21 (3050) (120) (130)
Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 77.5 89.5
A1670-*R01*01**-60* 1800 600
Inboard Pump 70.0 (4.27) 30 (1.831) 25 (3630) 28 (4060) (171) (197)
Outboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 77.5 89.5
A2270-*R01*01**-60* 1800 600
Inboard Pump 70.0 (4.27) 30 (1.831) 25 (3630) 28 (4060) (171) (197)
Outboard Pump 36.9 (2.25) 10 (.610) 16 (2320) 21 (3050) 86.5 98.5
A3770-*R01*01**-60* 1800 600
Inboard Pump 70.0 (4.27) 30 (1.831) 25 (3630) 28 (4060) (191) (217)
Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 88 108.5
A1690-*R01*01**-60* 1800 600
Inboard Pump 91.0 (5.55) 56 (3.42) 25 (3630) 28 (4060) (194) (239)
Outboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 88 108.5
A2290-*R01*01**-60* 1800 600
Inboard Pump 91.0 (5.55) 56 (3.42) 25 (3630) 28 (4060) (194) (239)
Outboard Pump 36.9 (2.25) 10 (.610) 16 (2320) 21 (3050) 100.5 121
A3790-*R01*01**-60* 1800 600
Inboard Pump 91.0 (5.55) 56 (3.42) 25 (3630) 28 (4060) (222) (267)
Outboard Pump 56.2 (3.43) 12 (.732) 16 (2320) 21 (3050) 107.5 128
A5690-*R01*01**-60* 1800 600
Inboard Pump 91.0 (5.55) 56 (3.42) 25 (3630) 28 (4060) (237) (282)
Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 109 134
A16145-*R01*01**-60* 1800 600
Inboard Pump 145 (8.85) 83 (5.06) 25 (3630) 28 (4060) (240) (295)
Outboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 109 134
A22145-*R01*01**-60* 1800 600
Inboard Pump 145 (8.85) 83 (5.06) 25 (3630) 28 (4060) (240) (295)
Outboard Pump 36.9 (2.25) 10 (.610) 16 (2320) 21 (3050) 121.5 146.5
A37145-*R01*01**-60* 1800 600
Inboard Pump 145 (8.85) 83 (5.06) 25 (3630) 28 (4060) (268) (323)
Outboard Pump 56.2 (3.43) 12 (.732) 16 (2320) 21 (3050) 128.5 153.5
A56145-*R01*01**-60* 1800 600
Inboard Pump 145 (8.85) 83 (5.06) 25 (3630) 28 (4060) (283) (338)
Graphic Symbol
"A" Series
M
O
1. Available to supply pump with anti-clockwise rotation. Consult Yuken for details.
2. Design Standards: None ........... Japanese Standard "JIS"
80 ............... European Design Standard
950 ............. N. American Design Standard