Professional Documents
Culture Documents
IC Engines Construction and Working
IC Engines Construction and Working
Mail id:
natrajpad@gmail.com
Thermal Engineering
Method of Evaluation:
Total Marks 50
Thermal Engineering
Course Content:
Unit I Internal Combustion Engines
Syllabus:
Review of construction and working of two stroke and four stroke
engines - Wankel engines - SI engines, Fuel systems - Simple
carburetor - Various compensation arrangements - Simple
calculations involved in carburetors ignition systems combustion
detonation factors and remedies - Rating of fuels -Type of
combustion chambers - Introduction to multi point and
microprocessor based fuel injection system. CI engines – Fuel
injection system - Fuel pump – Combustion – Knocking - Factors
and remedies - Rating of fuels - Types of combustion chambers -
Cooling and lubrication of IC engines.
UNIT – I INTERNAL COMBUSTION ENGINES
1. Internal Combustion
Engines
(Combustion of fuel
takes place within the
Engine)
2. External Combustion
Engines
(Combustion of Fuel
takes place Outside the
Engine)
UNIT – I INTERNAL COMBUSTION ENGINES
Internal External
combustion Engine Combustion Engines
Basic Nomenclature:
1. Cylinder Bore: (D):
is the nominal inner diameter of the working cylinder.
is usually measured in mm
2. Piston Area: (A)
Area of the circle diameter equal to the cylinder bore
is expressed in square centimeters
3. Stroke: (L):
is the nominal distance through which a working piston moves
between two successive reversals of its direction of motion.
is designated by “L” and is expressed in mm
4. Displacement or Swept Volume: (Vs):
The nominal value swept by the working piston when traveling from
one dead centre to the other.
is expressed in terms of cubic centimeter
Vs = (/4) d2 L = A X L
UNIT – I INTERNAL COMBUSTION ENGINES
Basic Nomenclature:
5. Clearance Volume: (Vc)
The nominal volume of the combustion chamber above the piston when
2. Compression Stroke:
Piston displacement = From BDC to TDC
Crank Revolution = Second 1800C and completes one
Revolution
Inlet Valve position = Fully Closed
Exhaust Valve position = Fully closed
Pressure inside cylinder = Moderately high Pressure
Temperature inside cylinder = Moderately high Temp.
Charge Condition = Compression of charge into the cylinder
INTERNAL COMBUSTION ENGINES
3. Expansion Stroke:
Piston Displacement = From TDC to BDC
Crank Revolution = third 1800C
Inlet Valve position = Fully Closed
Exhaust Valve position = Fully Closed
Pressure & Temperature = Decreases
During this stroke only power is produced by the system.
4. Exhaust Stroke:
Piston displacement = From BDC to TDC
Crank Revolution = Completes Two strokes
Inlet Valve Position = Fully Closed
Exhaust Valve = Fully Opened
Pressure & Temperature= Falls to atmospheric level a part of burnt
gas escape.
INTERNAL COMBUSTION ENGINES
Two stroke petrol Engine
INTERNAL COMBUSTION ENGINES
2. Downward Stroke or
Expansion Stroke:
Compressed charge is ignited by spark
produced by spark plug.
The piston is forced by gases and is pushed
down producing useful power.
The inlet port is covered by piston, the charge
is compressed in the crankcase.
Further piston, uncovers the exhaust port and
then transfer port.
The expanded gases escaping through the
exhaust port, fresh charge is already
compressed in the crankcase is forced into
the cylinder through the transfer port
simultaneously.
The charge strikes the deflection of piston
crown, rises to the top of the cylinder and
pushes out the most of exhaust gases.
Downward Stroke (OR)
The piston is now at the BDC position.
The cylinder is now completely filled with the Expansion Stroke
fresh pre-compressed charge.
The cycle is events is repeated.
INTERNAL COMBUSTION ENGINES
Working two Stroke Diesel Engine
6. Compression ratio 6 to 10 16 to 20
Higher rate of wear and tear. Greater Lower rate of wear and tear. Lesser cooling
4. cooling and lubrications are required. and lubrications are required.
No Valve mechanisms are used. But
Valve mechanisms are used for opening and
5. there are only ports are available
closing of inlet and exhaust valves.
regulates by piston itself.
6. The initial cost of the engine are less. The initial cost of the engine are high.
Volumetric efficiency is low due to lesser Volumetric efficiency is high due to more
7. time for induction. time for induction.
Thermal Efficiency is lower: Part load Thermal Efficiency is higher. Part load
8. efficiency is poor. efficiency is better.
Used where low cost, compactness, light Used where high efficiency is required. ie in
9. weight ie in mopeds, Scooters, Motor Buses, Trucks, Tractors, Generators, Power
cycles etc., generation etc.,