Professional Documents
Culture Documents
Goldstar Chassis Nc-44a (C-TV GCT-2505M CN-26B46 Service Manual)
Goldstar Chassis Nc-44a (C-TV GCT-2505M CN-26B46 Service Manual)
Goldstar Chassis Nc-44a (C-TV GCT-2505M CN-26B46 Service Manual)
SERVICE WARNING
Only qualified service technicians who are familiar with safety checks and guidelines should perform service work. Before replacing parts, disconnect power source to protect electrostatically sensitive parts. Do not attempt to modify any circuit unless so recommended by the manufacturer. When servicing the receiver, use an isolation transformer between the line cord and power receptacle.
SERVICING THE HIGH VOLTAGE AND CRT
Use EXTREME CAUTION when servicing the high voltage circllits. To discharge static high voltage, connect a 10K ohms resistor in series with a test lead between the receiver and CRT anode lead. 00 NOT lift the CRT by the neck. Always wear
SAFETY CHECKS - FIRE AND SHOCK HAZARD Cold Leakage Checks for Receivers with Isolated Ground Unplug the AC cord, connect a jumper across the plug prongs, and turn the power switch on (if applicable). Use an ohmmeter to measure the resistance between the jumped AC plug and any exposed metal cabinet parts such as antenna screw heads, control shafts, or handle brackets. Exposed metal parts with a return path should measure between 1M ohms and 5.2M ohms. Parts without a return path must measure infinity.
Hot Leakage Current Check
Plug the AC cord directly into an AC outlet. 00 NOT use an isolation transformer. Use a 1500 ohms, lOW resistor in parallel
with a capacitor to connect between metal
case
X·RAY RADIATION AND HIGH VOLTAGE LIMITS
Be aware of the instructions and procedures covering X-ray radiation. In solid-state receivers and monitors, the CRT is the only potential source of X-rays. Keep an accurate high voltage meter available at all times. Check meter calibration periodically. Whenever servicing a receiver, check the high voltage at various brightness levels to be sure it is regulating properly. Keep high voltage at rated value, NO HIGHER. Excessive high voltage may cause X-ray radiation or failure of associated components. 00 NOT depend on protection circllits to keep voltage at rated value. When troubleshooting a receiver with excessive high voltage, avoid close contact with the CRT. 00 NOT operate the receiver longer than necessary. To locate the cause of excessive high voltage, use a variable AC transformer to regulate voltage. In present receivers, many electrical and mechanical components have safety related characteristics which are not detectable by visual inspection. Such components are identified by a # on both the schematic and the parts list. For SAFETY, use only eqllivalent replacement parts when replacing these components.
TEST JIG HOOKUP
Chek·A-COlor PC Board
Function Adapter No. Plug No. Pin Color
CRl' B239 P401 I Yellow
Yoke 04137 2 Green
Yoke Setting YPI 3 Blue
Comments FocusThp 4 Red Use an AC voltmeter with at least 5000 ohms per volt sensitivity to measure the voltage across the resistor. Check all exposed metal parts and measure voltage at each point.
Voltage measurements should not exceed .75VAC, 500~. Any value exceeding this limit constitutes a potential shock hazard and must be corrected. If the AC plug is not polarized, reverse the AC plug and repeat exposed metal part voltage measurement at each point.
GENERAL GUIDELINES
Perform a final SAFETY CHECK before returning receiver to customer. Check repaired area for poorly soldered connections, and check entire circuit board for solder splashes. Check inner board wiring for pinched wires or wires contacting any high wattage resistors. Check that all control knobs, shields, covers, grounds, and mounting hardware have been replaced. Be sure to replace all insulators and restore proper lead dress.
VOlTMETER
any part no case or guarantee
Howard W. Sams & Company as to the quality and suitability of such replacement part. The numbers of the listed parts have
been compiled from infonnation furnished to Howard W. Sams & Company by the manufacturers of the specific type of
replacement part listed.
Reproduction or use, without express permission, of editorial or pictorial content, in any manner, is prohibited. No patent liability is assumed with respect to the use of the infonnation contained herein.
@1995 by Howard W. Sams & Company
2647 Waterfront Parkway East Drive, Suite 300 Indianapolis, IN 46214-2012
Printed in the United States of America 5 4 3 2 1
Page 1 SET 3541
95PF02781
o
6 0 41 2
TO ALL EXPOSED METAl. PARTS
PHOTOFACT.
a:
~
en c ....
o ~
INDEX
GridTrace Location
Main Board •• .. .. . .. .. . . . . . . ... 3
Ie Functions .•.•..................... 1
Important Parts Information 1
Miscellaneous Adjustments 1
Parts List 4
Placement Chart 1
Precautions .. . .. .. .. . .. . 1
Schematics
Audio I Video 2
Power Supply 2
System Control 2
Television .. . .. .. .. .. .. .. 2
Schematic Notes 1
Test Equipment 1
Test Jig Hookup .. .. .. .. .. .. .. .. . 1
Troubleshooting 1
Tuner Information 1
For Supplier Address,
See PHOTOFACT Annual Index
Technical Service Data
GOLDSTAR
Models GCT 2505M, C.N26B46 (Chassis NC-44A)
Model GCI'2505M Complete coverage
for servicing a television receiver •.•
• Schematics
• Component locations
• Parts list
• Troubleshooting guide
#f
HOWARD W. SAMS & COMPANY
SEPTEMBER 1995 SET 3541
PAl REMOTE PREAMP
Cl 47pF
5.0V
SYSTEM CONTROL SCHEMATIC
~ ~ ~TA
ll!!::2..
L- __ ~------------------------------------------------------------------------------------------------------ tgcK
ll!!::2..
R98
2200
6
lPARTc%
5.0V R96 L qOP-El~
2200
5
lPART OF
CAl~
5.0V R94 LqoP-E1
2200
4
lPARTc%
R92 L QOP-E1P
2200 02 lS2471
5.0V ls~b
5.0V
5.0V
R3 51K
011 lS2471
5.0V
5.0V
~~iriiW~2--------------~---------2"'Orl~V
PAGE 2A
C129 .01.
L- __ ~----------------------------------------~--------------------------------------------------~-------- ¥~
ll!!::2..
L_ __ ~-------------------------------------------------------------------------------------------------¥g
ll!!::2..
TUNER NOT INCLUDED IN THIS COVERAGE
NC
C6l lpF
Rl 9100
.6V 21
VIDEO HORIZ
IN SYNC OUT,..,, ...,
2.BV 4.6V 7
17
051
MUTE lS2471
OV 52
.._ =-IHORIZ SYNC SHARPNESS..,..,~ SEE IC501
~~~g 4.0V 2.7V 35 ~l~E 4~C
TINT SEE IC501
2.7V1-3"4,----- ~l~E 1 ~C
COLOR.J-,;,,-- ~~ ~~501
2.7V 33 PAGE 2C
3~~J3"'2;-------------------------::w;;-;:;;:;~--...,...:.w;;..-r---:=:-:f"--WV--- ~~ ~~501
R60 PAGE 2C
B~~.---:-:f"_I~I~O---OV 24 C18
VOLUME 100pF •
2.W 30
R67
TV /VIDEO 1000
OV 38 R57 R6l0
. . ST4s:6 ~7K --- ----- 1 OaK . --------- ---- -.---.-.----------- .. -.---.------ .---.--.----.--.-.
",-=::::.__.,...,..LCI (OSD) . ~i~ ~C782
14 4.8V PAGE 2F R58
110
5.0V
KTC3198 0100 VIDEO AMP
C67 lpF
R83 100
SEE IC781 PIN 6 PAGE 2B
C56 .0015 I
SEE IC501 PIN 22 PAGE 2C
R87
100 SEE IC602 PIN 4 PAGE 2F
5.0V
R18 33
C70
.0151 100V
ST/MONO 4.7V 4
12.0V
NC
SEE IC781 PIN 5 PAGE 2B
SDA 5.0V 11.5V
OV 7
SCL
4.8V 8 R85
MPX ADJ 47K
5.0V 17
ST. IND. 5.0V
5.0V 18
R643
R56 47K
POWER 1000 SEE Q802
OV 5 BASE
PAGE 2E
5.0V R638
110 7
6 OV GCT2402C
IC101
R639 EEPROM
110 2
5 4.8V
3
4 R6l 110
5.0V
G
H
,
, - !
NC
R129
2.2 12V
TO
~
R130
180 5V
lW TO
C152 ~
ZD10l •011
12.0V HZ5C2
5.W I
I
I
I
I
a:::
0
c
m
r-
(/)
Q
~
~
0'1
~
j:
(')
z
~
eft
se
eft
-
(')
::r
m
==
;;
z
t
.!: NC
NC NC
ANTENNA SHIELD BOX
UHF/VHF~
ANTENNA TO
INPUT ~
75 R999
3.3M
----------------.----.--~-~--,~.------------- ----------i
ADDmONAL SCHEMATIC NOTES, SEE PAGE 1
VOLTAGES TAKEN WITH SIGNAL
A PHOTOFACT STANDARD NOTATION SCHEMATIC
WITH '4i;MiilMW
II) Howord W. So.,. & Co. 1995
SET 3541
Page 2
Obtaining Parts Q .
.. ~~~~::::::========::::::======================================~~~----~~~-~~~~~~--~~--~~~~~--~~~~~~~:~~~~~~~~~~~~-~~~"~~~~~~~~~>~
Many of these parts are available from your local Sarns authorized distributor or the manufacturer of the equipment. Call ~
Sams for the name of your nearest distributor: ;;!
:a
TUNER INFORMATION
TUNER VOLTAGE CHART
Pin VHF Low Band VHF High Band UHF Band Pin VHF Low Band VHF High Band UHF Band
CS .1V .IV .IV l2V l1.9V l1.9V l1.9V
DATA 4.9V 4.9V 4.9V AGe 6.9V 6.9V 6.7V
CLK .1V .1V .IV NC 1.3V 4.SV 6.SV
LOCK OV OV OV
5V 4.9V 4.9V 4.9V N01E: VHF Low Band voltages taken on channel 2.
33V 30.0V 30.0V 30.0V VHF High Band voltages taken on channel 7.
IF OV OV OV UHF Band voltages taken on channel 14. TUNER TERMINAL GUIDE
CS
AGe NC
RF
CLK
5V
IF
DATA
l2V
LOCK 33V
SCHEMATIC NOTES
Waveforms and voltages are taken from ground, unless noted otherwise.
Waveforms taken with triggered scope and colorbar signal.
Waveform voltage is peak to peak. Timebase
~ Circuitry not used in some versions.
Circuitry used in some versions. -+- Ground
_ Chassis ground
V Common tie point
/::;, Taken from common tie point
is per division. Waveforms shown at 10 divisions.
Supply voltages maintained as seen at input.
Voltages measured with digital meter and a lOOOJ.lV RF
signal, with colorbar pattern, applied to antenna terminal.
Controls adjusted for normal operation.
Capacitors are 50 volts or less, 5% or greater unless noted. Electrolytic capacitors are 50 volts or less,
20% or greater unless noted.
Resistors are 112W or less, 5% or greater unless noted. Value in ( ) used in some versions.
Measurements with switching as shown, unless noted. Rated voltage shown on zener diodes.
II Schematic
CIRClJITRACE ®
: Voltage source tie point.
A- Cabling: Heavy lines reduce use of multiple lines.
Important Parts Information
• The" parts listed here are those not usually available from a well·stocked supply cabinet or bin.
• Where ~erns may be replaced with equivalent parts, several alternates are shown from participaijng vendors.
• On the parts lists, safety items are marked with a # to remind you that only exact replacements are recommended for these ~erns.
• When ordering parts, state the model number, part number, and description.
800-428·7267
Or consult the Sams Annual Index for the address of the original equipment manufacturer.
Participating Vendors
Information on test equipment and replacement parts is listed in these pages for the following participating vendors. Consult the Sams Annual Index for their current address.
II Custom Components Corporation (Chek·A-Color)
• NTE ElectroniCS, Inc. (NTE)
• Philips ECG Company (ECG)
• PTS Electronics Corporation (PTS)
• Sencore, Inc.
• Thomson Consumer Electronics, Inc. (SK, TCE)
I
I
,
( ...
TEST EQUIPMENT
I
t ' [
!' .. I
a:
0
c
m
....
en
Q
!l
~
UI
0
UI
1=
n
z
~ I
0)
! !
0) I.·
- I-
n
::r I
I [
I
ii" I "~
z
t
.!: Test equipment listed by participating manufacturer illustrates typical or equivalent equipment used by Sams engineers to obtain measurements. This equipment is compatible with most types used by field service technicians .
.. __ ~ __ ~ ~_!_~~~~~~ __ ~~~~~ __ ~~ __ ~ __ ~~~~~~~~~~~~--~~-I--------·~----tc
Equipment SencoreNo. equipment SencoreNo.
Oscilloscope SC3100 Isolation Transformer PR57
Generators Capacitance Analyzer LCIOI, LCI02
RGB CM2000 CRT Analyzer CR70
Multiburst Signal VG91 AC Leakage Tester PRS7
Color Bar VG91 Inductance Analyzer LCIOI, LCI02
TV Stereo VG91 Flyback Yoke Tester TVA92
Digital VOM SC3100 TV Stereo Power Monitor SR68.PA81
Frequency Meter SC3100 FJeld Strength Meter SL7S0
Hi-Voltage Probe HP200 Transistor Tester TF46
Accessory Probes TP212 Video Analyzer VG9I, TVA92 i ,.
i
I t
,
I
I
I"
SET 3541 Page 1
POWER SUPPLY SCHEMATIC
AUDIO I VIDEO SCHEMATIC
11.5V
LA7222 IC782 SWITCH
BUFFER
C6l8
~i~ ~~50l 4.~7~~ ~~~~~~
PAGE 2B
11.5V
100V SOURCE
C642 1
AN5265 IC602 AUDIO AMP
SP1 r-----~~>------~"\BZ
t,. TAKEN FROM COMMON TIE POINT V
20.0V
~i~ ~%1 ---------;t-----.-AM,----,-I
PAGE 2.G&H
L _
--..,
SEE Q707 +--- BASE PAGE 2B
.5VIh-~~~~----------------------ilJI~§~RCE ~~~-----------------------4~~§~RCE L..:;~':"":"_ ,!-_--..,....-----1----.- .... ~§~RCE
VOLTAGES TAKEN WITH SIGNAL ADDITIONAL SCHEMATIC NOTES, SEE PAGE 1
A PHOTOFACT STANDARD NOTATION SCHEMATIC
WITH ';M§"II#!#G
10 Howard W. Sarna &: C9. 1995
12.0V
Page 2
SET 3541
E
F
Page 1 SET 3541
MISCELLANEOUS ADJUSTMENTS
TROUBLESHOOTING
Connect a color bar generator to the antenna input and tune in a dot Check F80I, if open, check D801 thru D804, C80I, C803 thru C806,
pattern. Loosen the convergence magnets clamp screw. Adjust the 4 and T801. Apply 120VAC and check for 12.0V at the emitter of
pole magnets to converge the red and blue dots at the center of the Q801 and S.SV at pin 1 ofIC3. If the standby voltages are missing,
screen. Adjust the 6 pole magnets to converge the redlblue dots over check Q801, IC3, D80S, and ZD812. Press power button and check
the green dots at the center of the screen. for lS4V at the cathode of D802. If the voltage is incorrect or
missing, check RLSOI, pin S of ICI, Q802, and Q803. Check for Inject a video IF signal at the base of QI0l and check for video on
NOTE: Rotate the two tabs of each set of magnets equally and 101V at pin 4 of1C80l. If voltage is missing, check IC801, F802, the CRT. If video is present, check the tuner and components
opposite to converge vertically and rotate both tabs in the same and T802. If voltage is present, refer to the "Horizontal" section.of associated with the tuner. Check for a video waveform at the base of
~tion to conve~ge horizon~y. The 4 and 6 pole ~gnets this Troubleshooting guide. Q201. If video is present, refer to the "Video" section of this
VERTICAL HEIGHT mteract, repeat adjustment until center convergence IS correct. .. ..... .. . . . .. .. .. . .... Troublesh~ting guide. Apply Am: bias ~_p~ 2 o~IC~Ol. ~"vi~~_.~~
~.~ ... ~. ~.~~. ~.~.~ .. ~,~~~ ... _ .. - .• _ ... _" -.~~_.~"~ .. ~." _. ~."~.-~ .. ~" ~···-~.----'!=>~m~.$('9~~~~~R«nG"~th&rOObe~esGll~t"~;t .. "··~~~~~·~" -~ .. _._. 1iORiZONT1\r-· ~. ~-~~- ~-.~-,~~--~~--.~-."."~~" ~~~~"-~~S on fiieCR'l"";Clieci p1iiS3,4,1O~r.anQ41 on:e.sm:.1f
Tune in a picture. Adjust VR316 for a slight overscan at the top and deflection yoke and the CRT. Loosen the deflection yoke clamp video is missing, check QIOI and IC501.
bottom of the screen. screw. Tilt the deflection yoke up or down to converge the vertical Determine if the receiver is in hold down, refer to "High Voltage
lines at the top and bottom of the screen and the horizontal lines at Hold Down" section of this Troubleshooting guide. If the receiver is
the right and left sides of the screen. Tilt the deflection yoke to the not in hold down, press the power button and check for a horizontal
right or left to converge the horizontal line at the top and bottom of drive signal at pin 33 of IC501. If the horizontal signal is missing,
the screen and the vertical line at the right and left sides of the check pins 29 thru 33 of ICSOl. Check for a horizontal output signal
screen. Replace the rubber wedges. Tighten the clamp screw. at the base of Q40 1. If horizontal signal is missing, check Q402 and
Tighten the screw on retainer. T40l. If horizontal signal is present, check Q401, T402,0403, D301, 0409, and D70l. The high voltage rectifier is part ofT402 and if defective will affect the operation of the horizontal circuits. Width or foldover problems may be caused by C416, C417, and C499.
HIGH VOLTAGE CHECK
CONVERGENCE
POWER SUPPLY
Tune in a picture and set brightness, contrast, and color to minimum. Connect a high voltage probe to CRT anode. High voltage range should be 26.SkV to 28kV.
HORIZONTAL CENTERING
Tum receiver on and tune in an active station. Adjust VR431 for best horizontal centering.
RFAGC
Tum receiver on and tune in an active station. Tum VR204 fully clockwise, then counterclockwise to a point where snow just disappears.
SUB BRIGHTNESS
PURITY
Tune in picture. Set color, contrast, and brightness to minimum. Adjust VR232 to a point where highlights are just visible.
NOTE: Operate the receiver for IS minutes to allow warm up of CRT.
ON SCREEN DISPLAY POSITION
Use a degaussing coil to demagnetize the CRT. Set contrast and brightness to maximum and color to minimum. Tune in a green raster. Loosen the convergence magnets clamp screw. Adjust purity tabs to center the vertical green band. Loosen the deflection yoke clamp screw. Slide the deflection yoke forward to produce a uniform green screen. Tighten both clamp screws.
HIGH VOLTAGE HOLD DOWN CHECK
Adjust L2 to center the on screen display on the lower portion of screen.
Apply power and turn the receiver on. Momentarily short between the unconnected end ofR423 and the anode ofD410. The receiver should lose sound and raster. If receiver does not lose sound and raster, the hold down circuit should be repaired. To restore operation, remove AC power for at least 30 seconds, then apply power and turn the receiver on.
EXTERNAL VIDEO LEVEL
Connect a IVp-p video signal to the video input jack. Connect an oscilloscope to base of Q706. Adjust VR751 for I.SVp-p.
CRT NECK ASSEMBLY
HIGH VOLTAGE HOLD DOWN
EXTERNAL AUDIO LEVEL
NOTE: Care should be taken in defeating the high voltage hold down circuit as this may cause excessive x-ray radiation and damage to the CRT and T402. Monitor the high voltage and troubleshoot.
The high voltage is monitored by D407 rectifying the pulses from T402. Should the high voltage increase, the voltage at the cathode of 0410 also increases and triggers ZD402. This causes the deflection portion oflCSOI to shut down the horizontal drive signal oflCSOl, causing the receiver to lose audio and raster. To troubleshoot, remove ZD402 from circuit, use a variable power supply for AC voltage. Start at 70V AC and troubleshoot to locate the defect. Reconnect ZD402 to circuit.
Purity Cony. Magnets Four-Pole Cony. Magnets Six-Pole Cony. Magnets
rCony. Magnets
, Clamp Screw
Connect a 1kHz audio signal to the audio input jack. Connect an oscilloscope to emitter of Q70S. Adjust VR7S3 for 1.SVp-p.
WHITE BALANCE
Tune in an active station, allow a 10 to 30 minute warm up time. Set
_. __ ~Q}m:._bJightness~ntrast_~ree.n._YR2_l2,_YR222,_and_.YR.232~ __ ~ ~~ - ~~ - ._" - ". _~.~-~-.-~--- ... -.-.-.-----~-
controls to minimum. Set VR911 and VR931 controls to midrange. ~ L
Set SWSOI to service position. Advance the screen control until a -~.
faint line of one predominant color appears on the screen. Adjust the
two remaining bias controls for a dim white line. Set SWSOI to Deflection Yoke Retainer Ring
normal position. Adjust VR911 and VR931 for best black and white picture on screen.
VIDEO
Inject a video signal at the base of Q201. If video is present on the CRT, refer to the "IF AGC" section of this Troubleshooting guide. Check for a video waveform at pin 41 ofICSOI. If the waveform is
missing, check IC781 , Q201, and Q202. Check for luminance signal at pin 26 of ICSOI. If missing, check ICSOI. If present, check Q20S. If the brightness is inadequate or cannot be controlled, check Q22I, pin 37 ofICSOl, and pin 7 of the CRT.
IFAGC
VERTICAL
Inject a vertical signal at pin 2 of IC301. If vertical deflection is present, check pin 31 oflCSOl. If vertical deflection is missing, check SW30I, IC301, and the deflection yoke. Vertical linearity or foldover problems may be caused by sweep shaping and bias circuits, check C302, C30S, C306, C31 0, and C311.
RASTER
Check the CRT and CRT voltages. If red is missing, check pin 23 of ICSOl, Q912, and Q911. If green is missing, check pin 2S oflCSOl, Q922, and Q921. If blue is missing, check pin 24 of ICSOI, Q932, and Q931. If the raster has a keystone shape, check the deflection yoke. If the raster has height or width problems, refer to the "Vertical," "Horizontal," or "Power Supply" sections of this Troubleshooting guide.
CHROMA
Check for a chroma waveform at pin 43 of ICSOl. If the waveform is missing, refer to the "Video" section of this Troubleshooting guide. Check for the proper waveforms at pins 23, 24, arid 2S of ICSOI. If these waveforms are missing, check ICSOI. Check the 3.S8MHz oscillator at pins 13 and IS ofICSOl. If there is inadequate tint range, check pin 16 of ICSO 1. If the proper waveforms are present at pins 23, 24, and 25 of ICSO 1, refer to the "Raster" section of this Troubleshooting guide.
AUDIO
Select a station and check for an audio waveform at pin 2 of IC602. If missing, check pins 1,6,9, and S3 thru S6 ofICSOl. If present, check for audio waveforms at pins 10 and 11 of IC782. If present, check IC602. Check the volume control voltage at pin 4 of IC602, it should be .SV in mute and 10.SV at maximum volume.
c
TELEVISION SCHEMATIC continued
~i~ ~~1 -,
~
R290 4.7
P901
-y
SEE IC1
PIN 23 --,
~
SERVICE
P901
D
SET 3541
SEE T402 PIN 9
~
X
P902 3
P902 HT R940
.68 FUSIBLE
2W
TO CRT SHIELD
G-Y
HV,E
HV RANGE 26.5kV TO 28kV
L-----~---~~~~~~~~~~&~CE L-~~----~~.-~~~J~RCE
A2
A3A4
----------------------------~----~~----------~~------------------------------------------------------------------------------------------------------------------------------~~~A
A1
P/902 P902 n2o>-3-p .... G::>-~-1 --, GND
Page 2
C904 .0022 2kV
G2
VOLTAGES TAKEN WITH SIGNAL
ADDITIONAL SCHEMATIC NOTES, SEE PAGE 1
A PHOTOFACT STANDARD NOTATION SCHEMATIC
WITH ijM§il.i@G
(C) Howard W. Sam. &< Co. 1995
A3A4
PLACEMENT CHART
5.0V 5.0V
SWl POWER
MAIN BOARD
SW2 CH+
SW3 CH-
SW4 VOL+
F801 -0\;>-
ICl
L2
@]
= 132
032 IC3 RL801
0@2D '-1---""1 T801 P801
Q~01Q803 0801, 0 ~:J._--.5_.0_V
52
IC10l 0
:0: Q4
Ql02 o
IC781
504
8 1
Ql0l IC501
D 56 Ll06
L223
@]
X501<1s- IC301
1
T
28 29
X401;;!;
T
12 4
D Q205 '" _
SW501 I •••••• 1 P903
IIIIIiiiiiiiiii 0
NORMAL SERVICE Q204
Kt] L203
VR431 HORIZ
CENTER
o
o Q706
Q705
IC702 IC701 6 4 8 5
DD
1 3 1 4
-.t -
~P902
FOCUS & SCREEN
Q221
D
11.0V.I!> 20.0V 12.0V
t:. TAKEN FROM COMMON TIE POINT V
5.0V
SET 3541
Page 1
IC FUNCTIONS
CRT BOARD ICSOl
TA8825AN
Q912
Q932
DI~I D
~ 56
- Kt] VR912
VR911 RED BIAS
RED DRIVE Kt] Q922 55
D Kt] VR922
Kt] GREEN BIAS
][ 54
Kt] .VR932
BLUE BIAS SIr
Q921 \ICC 53 IC2 LA7945N
4
2 ~r-1~~~EP~c~~====~====li~
3 ~H. SUCER h
VERT L 20 SEP I
'-----'
5 i-- H CLOCK JGEN
LPF
7
8
Q
YL--rVC_0-r-...J
11 t------__.J IL...- ---i 12
10
HORIZ c/o
AFCl r- 13
IC602 ------------------ANo265--------------
IC801 sTR52TOOI\
IC301 TA8445K
22
21
lQ
111
17
18
15
27 ~~z
2B~-------------------~
t-----t2Q
Page 2
SET 3541
B
A
TELEVISION SCHEMATIC
VOLTAGES TAKEN WITH SIGNAL ADDITIONAL SCHEMATIC NOTES, SEE PAGE 1
A PHOTOFACT STANDARD NOTATION SCHEMATIC
WITH ;;';&'iI.¥!§a
«:> Howard W. Soms &: Co. 1995
SEE IC1 PIN 20
~
C128 4.7pF
C130 .0033
~~
9.0V
C204 .01
R101 75
SEE Q100 BASE PAGE 2H
TUNER NOT INCLUDED IN THIS COVERAGE
SEE Q706 COLLECTOR PAGE 2F
C226 .01
,fH~
9.0V
AGe RANGE 4.BV TO 7.2V
SEE IC1 PIN 38 PAGE 2G
TA8445K IC301 VERT OUTPUT
I I I I I
l ~~Q~ _
FB410
~
R204
T402 BOTTOM VIEW
ALA1 __ ~~ ~
Page 3 SET 3541
SET 3541 Page 3
MAIN BOARD
S R Q P 0 N M L K J H G F E D C B A
1
2
3
4
5
6
7
8
9
10
11
12
13
14 A HOWARD W. SAMS iiJijj.i1#,'P PHOTO
Page 4 SET 3541
PARTS LIST
SEMICONDUCTORS
(Select the replacement that gives the best results.)
Item No. Type No.
Dl,D2,04 IS2471
D9,11 1S2471
D13 Thru
D18 IS2471
D31, 32, 33 IS2471
049,51 IS2471
D201 Thru
'""~----~~ D204 IS241L
-_- -D30"i:04 RUlM
RU-2MV
0305,06 IS2471
D401 IS2471
D403 RU-IAV
D407 RU-IA
RU-IAV
0409 RU3AM
RU3AMV
D410 IS2471
D701 RU1A
RU-IAV
D703 lS2471
1# D80l Thru
1# D804 RMIIAV
RMI1AVM
D80S GP1SJ
D806 RU-IAV
D807 RGP1SJ
D808 RG-2V
RG2
D809 RU2AMV
RU-1AV
D810 RGPlSJ
D811 RU4AM
D8B lS2471
D814 IN4003
1N4003A
D821 lS2471
D911 Z12BMTA
MTZl2B
D912 MTZ3.6B
ZD3.6
D914,21 IS2471
D931,38 IS2471
ICI GS8308-16B
LC864016B
IC2 LA794SN Mfr. Part No.
ODD247109AA ODD247109AA
ODD247109AA ODD247109AA ODD247109AA
ODDlOOOO9AE
ODD300009AC ODD247109AA
ODDl00009AE ODD247109AA
ODDllOOO9DA
ODD1S0009CE ODDlOOOO9AE ODDlS0009CA ODD200009AC
ODD200009AH ODDl00009AE ODDlSOOO9CA ODD410000AD ODD247109AA
ODD400309AD ODD247109AA ODZ120009AA
ODZ360009DA
SET 3541
SEMICONDUCTORS continued
CAPACITORS & ELECTROL YTICS
SK3100 SK3100
QI02
BOOS19 BOOS19
BOOS19 BOOS19 BOOS 19
ECG12S ECGSS2 ECGS80 ECGS80 ECGS80 ECGSS2 ECGSS2 ECGS80 ECGS80 ECGS19 ECG116 ECG116 ECGS19 ECG5021Tl ECG5021A
(Select the replacement that gives the best results.)
NTE Part No. ECG Part No. TCE PIIt No.
ECG8S ECG8S ECG376 ECG376 ECG8S ECG8S ECG376 ECG376 ECG8S ECG8S ECG376 ECG376 ECG8S ECG8S ECGSOI0A ECGS03SA
NTES19 NTES19
NTES19 NTES19 NTES19
NTEI25 NTESS2 NTES80 NTES80 NTES80 NTESS2 NTESS2 NTES80 NTES80 NTES19 NTE116 NTE116 NTES19 NTES021Tl NTE5021A
Item No.
Type No.
Mfr. Part No.
NTE Part No. ECG Part No. TCE Part No.
Ql00
QI01
SK3100 SK3100 SK3100
SK.3081 SK9000 SKS036 SKS036 SKS036 SK9000 SK9000 SK5036 SK5036 SK3100 SK3113 SK3311 SK3100 SK9971 SKllA
Q801
Q802
Q803
NTE8S NTE8S NTE376 NTE376 NTE8S NTE8S NTE376 NTE376 NTE8S NTE8S NTE376 NTE376 NTE8S NTE8S NTESOI0A NTES03SA
Item No.
Rating
Mfr. Part No.
Q911
Q912
OTRl06800BA OTR319809AA OTR319809AA
OCCI0I0K41S 181-064R 181-4S2G
Q921
Q922
OTRl06800BA 0TR319809AA 0TR319809AA
181-091G 181-128B OCK2220WSlS
OCK2220WSlS 181-102E OCEI07BP61A OCK22202S10 167-102D
1# For SAFETY use only equlvaleot replacement part.
SK9229 SK3124A SK3219 SK3219 SK9229 SK3124A SK3219 SK3219 SK9229 SK3124A SK3219 SK3219 SK9229 SK3124A SKSA1 SK30A
441-332A 300-A77E 300-A77A 303-068H 401-734E
Q931
CABINET PARTS
Item
Mfr. Part No.
Q932
Model No GCT2505M
Button Control
Cabinet Front Assembly Cabinet Front Assembly Cabinet Rear
Plate - AntennalAudiolVideo Input
IC101 X24C02P OIXI240200B ZD30S.06 MTZ30B ODZ300009BA NTES03SA ECGS03SA SK30A #f
GCT2402C ZD401,02 MTZ9.1B ODZ910009BA NTE139A ECG139A SK9V1
IC301 TA844SK OIT0844S00A ZD403 MTZ3.6B ODZ360009DA
ICS01 TA8825AN 01T0882S00B ZD404 M1'Z6.8B ODZ680009AA NTES014A ECGS014A SK6A8 Created with pride by the
IC602 ANS26S 0IMA526S00B NTE1789 ECG1789 SK9876 ZD40S MTZ9.1B ODZ910009BA NTE139A ECG139A SK9Vl
1# IC70l TLP651 OIT0651000A ZD702 MTZllB ODZllOOO9AA NTES020A ECGS020A SKIIA employees of Howard W. Sams
1# IC70l TLP631 0IT0631000A NTE3041 ECG3041 SK2041 ZD812 RDllFBD2 ODZ112009AD NTES074A ECGS074A SKllV & Company.
IC781 GL3820 01GS382000A ZD938 MTZ3.6B ODZ360009DA
IC782 LA7222 OISA 722200A NTE7066 ECG7066 J. Barker, N. Beck, B. Bryant,
1# rcser STR52100A OISKS21000A 1# For SAFETY use only equivalent replacement part. B. Buchanan, T. Clensy;
Q1,Q4 KTC3198-TP-Y 0TR319809AA NTE8S ECG8S SK9229 D. Cobb, G. Farrell, B. Fink,
KTC181S OTR319809AA NTE8S ECG8S SK3124A M. Herkless, J. Kocha,
1# For SAFETY use only equlvaleot replacement part. R Malek, B. Medaris,
R. Raus, B. Skinner, J. Young Page 4
Antenna C12l L-5 C227 1-8 CSOI B-13 D809 1-12 L204 N-6 R24 C-9 R9l B-8 R2l9 L-7 R4ll L-7 R812 0-10
Shield C122 0-7 C244 0-6 C803 B-13 D8l0 H-12 L206 0-7 R25 C-9 R92 B-8 R220 L-8 R4l2 L-12 R813 o-n
Box S-7 C123 0-7 C300 L-10 C804 D-12 D8ll 0-13 L22l H-7 R26 C-8 R93 B-8 R221 0-10 R4l3 N-IO R8l4 n-n
C1 B-12 C128 H-4 C30l K-IO C805 B-14 D8l3 e-n L222 1-7 R27 D-7 R94 B-8 R222 0-10 R4lS L-13 R830 e-n
C2 A-ll C129 F-4 C302 K-IO C806 0-11 D8l4 F-9 L223 J-7 R28 C-9 R95 B-8 R223 0-7 R4l7 0-12 R883 1-12
C4 B-6 C130 a-t C303 K-lO C807 1-14 D82l B-ll L402 M-14 R29 0-10 R96 B-7 R230 R-7 R4l8 N-8 R800 B-14
CS B-S C13l 1-7 C304 J-lO C809 H-14 F80l A-13 L403 K-12 R30 B-9 R97 B-9 R23l R-7 R4l9 N-8 R999 R-7
C7 C-lO C132 H-8 C305 K-ll C8l0 H-12 F802 F-13 L40S 0-9 R3l B-1O R98 B-7 R232 Q-14 R420 S-9 RL801 C-12
C8 D-9 C133 1-7 C306 x-u C811 J-14 FB301 L-1O L70l 0-3 R32 0-8 R99 A-2 R233 P-14 R42l R-9 SWI A-4
C9 0-9 Cl34 1-8 C307 M-ll C8l2 N-14 FB410 0-12 LBOI L-14 R33 F-8 RlOO F-7 R234 Q-14 R422 R-9 SW2 A-5
CIO D-8 C135 1-7 C3l0 K-9 C8l3 0-14 FB501 M-5 P40l L-12 R34 F-8 RlOl K-3 R235 Q-14 R423 S-9 SW3 A-6
Cll D-9 C136 J-7 C3ll L-IO C8l4 0-13 FB502 M-5 POOl P-6 R36 B-8 R102 J-3 R236 R-14 R425 0-5 SW4 A-8
Cl2 C-4 Cl37 J-7 C312 P-I0 CS15 1-9 FB503 M-4 P80! C-14 R37 B-8 RI03 1-3 R237 F-8 R426 E-4 SWS A-9
C15 B-lO C139 K-7 C3l3 M-9 CS16 F-14 FB801 0-13 P90l 0-13 R38 B-9 Rl04 H-6 R238 R-14 R427 P-9 SW6 A-lO 8 I
C16 D-4 C14l M-3 C3l4 F-7 C8l7 a-n FB802 B-lO P902 R-9 R39 F-6 Rl05 1-3 R246 0-5 R428 L-13 SW301 M-lO .- I
~~~,-~~~- .. ~~~-.- .... ~-'~~~~-ej?-~--D=4-~'C-nr~-~' '1:r"'2~-'C40r"~' '~"L-/~~' ~8rg-~c:rO~'-~1IR3I/~~P:V~-t'9{T)-~YVr-3'~--"'-K4(J"'"~~1r-5"~~--RW7~-"~-T-3~-~--"W.::()'~ ~""1Vr29~---'""F-=4~ --SW3or~«-4-- .~~~"-"-~-~~--~---. ~~-~~!-
C18 D-4 C143 N-l C403 M-7 C888 J-12 FR4l6 Q-9 PAl A-12 R4l H-5 Rl09 H-4 R25l R-8 R430 L-13 T40l N-ll ~ i-,
C19 E-4 Cl44 M-3 C405 M-6 CAl B-5 FR4l7 Q-9 PJ1 8-4 R42 D-9 RllO H-4 R252 S-8 R43l M-6 T402 Q-12 ::D '
C2l B-4 C145 K-l C406 8-9 DI B-7 FR4l8 R-IO Ql F-6 R43 D-8 R1l2 K-3 R2S4 R-7 RS27 K-5 T70l R-7 I
C22 C-4 C146 H-2 C407 0-8 D2 B-7 FR4l9 R-IO Q4 C-2 R44 D-9 R1l3 K-4 R255 S-8 R609 0-3 T80l C-13
C23 B-9 C147 1-2 C408 0-8 D4 A-8 FR420 8-10 QlOO F-8 R46 B-9 R1l4 K-4 R256 M-4 R6l0 0-4 T802 0-13
C30 B-7 C148 J-2 C409 P-9 D9 B-lO FR703 R-1O QlOl J-3 R48 B-9 R1l5 1-4 R257 M-4 R62l 0-7 TH901 B-14
CSO C-4 C149 r-i C4l2 M-11 Dll D-4 FR801 1-11 Ql02 1-4 R49 C-6 R116 1-4 R200 N-5 R628 0-5 VR204 K-7
C5l D-3 C150 r-t C4l3 M-lO DI3 C-9 FR805 M-14 Q20l H-8 RSO B-3 R1l7 1-4 R26l H-6 R629 P-5 VR232 R-7
C52 C-2 C15l J-2 C4l4 N-13 DI4 C-8 FR806 P-8 Q202 H-9 RSI 0-4 R1l8 L-3 R270 H-9 R630 P-6 VR3l6 N-9
C55 B-2 C152 K-2 C4l6 M-12 DI5 C-8 ICI C-5 Q203 H-IO R52 B-3 R1l9 L-4 R200 N-5 R63l P-6 VR431 N-7
CS6 B-7 C153 x-t C4l7 M-12 DI6 D-7 IC2 B-6 Q204 N-6 R53 B-3 R120 L-4 R299 N-8 R632 0-6 VR751 P-3
CS9 B-7 C154 H-3 C4l8 M-12 DI7 C-9 IC3 B-11 Q205 M-4 RS4 D-4 R12l L-5 R30l M-7 R638 C-2 VR753 P-2
COO D-7 C155 1-3 C4l9 K-13 DI8 D-6 IC4 F-9 Q22l 8~14 R56 B-9 R122 1-6 R302 M-8 R639 C-2 Xl C-4
C6l F-6 C156 0-7 C42l R-8 031 F-4 IClOl c-r Q30l F-4 R57 B-3 R123 1-5 R303 M-8 R643 0-3 X40l M-6
C63 B-7 ClS7 H-7 C422 Q-9 D32 B-lO IC301 K-9 Q40l N-12 R58 B-3 Rl24 1-7 R304 K-1O R64S 0-5 XSOI L-S
C64 B-7 C158 0-8 C423 R-lO D33 B-lO IC501 K-6 Q402 M-11 R59 B-7 Rl25 M-3 R30S K~lO R70l Q-6 ZlOl 1-4
C65 B-7 C200 H-9 C428 K-13 D49 B-2 ICOO2 0-5 Q403 E-4 ROO F-4 R126 K-7 R306 K-lO R702 R-S Zl02 K-4
C67 F-7 C20l 0-9 C43l M-6 D5l F-5 IC701 0.3 Q70l Q-2 R6l C-3 Rl28 M-3 R307 x-u R704 R-S Zl03 H-8
C68 D-8 C202 K-8 C432 N-8 D20l R-8 IC702 Q-2 Q703 R-2 R62 C-lO R129 L-2 R308 L-11 R707 R-3 ZDlOl L-l
C69 D-7 C204 H-1O C433 M-6 D202 S-8 IC781 0-6 Q705 P-2 R63 B-9 R130 M-l R3l0 K-IO R708 R-3 ZDl02 H-3
C70 F-S C206 H-8 C499 N-12 D203 S-13 IC782 N-2 Q706 P-2 R64 A-2 R13l K-8 R3ll 1-10 R709 R-3 ZD202 0-7
C7l F-4 C207 J-8 C6l8 N-l D204 8-10 IC801 J-12 Q707 0-3 R65 A-2 Rl34 H-S R3l4 K-12 R711 R-2 ZD203 M-3
C83 c-i C208 L-8 C630 0-5 D30l P-lO Ll A-ll Q80l C-lO R67 0-5 R136 K-3 R3lS K-12 R713 R-2 ZD302 K-10
C84 c-r C209 1-8 C63l 0-6 D304 L-ll L2 C-3 Q802 C-lO R68 F-9 R137 1-7 R316 F-4 R71S R-2 ZD305 L-ll
ClOl 1-3 C210 K-7 C632 P-6 D30S J-lO L3 D-2 Q803 e-n R70 0-4 R16S 1-4 R3l7 E-4 R717 S-2 ZD306 L-ll
C103 1-4 C2ll H-9 C633 0-6 D306 J-11 Lll B-S R1 F-S R71 C-3 R200 K-7 R318 1-10 R720 Q-3 ZD401 Q-9
CIOS 1-5 C2l2 0-8 C638 P-7 0401 P-9 L12 F-S R2 C-2 R72 B-7 R20l H-8 R3l9 0-5 R72l 0-3 ZD402 R-8
Cl06 1-5 C2l3 L-7 C639 P-8 0403 0-11 L13 B-5 R3 D-4 R73 B-7 R202 H-8 R320 0-9 R722 P-3 ZD403 Q-8
Cl07 1-4 C2l4 B-9 C642 N-2 0407 R-1O L14 H-5 RS C-6 R74 B-7 R203 1-7 R322 1-11 R723 P-3 ZD404 N-7
Cl08 K-S C2lS L-7 C643 P-7 D409 0.10 Ll02 1-3 R8 H-6 R7S D-8 R204 1-9 R323 P-9 R724 Q-2 ZD405 0-9
Cl09 K-3 C2l6 1-10 C646 P-6 D4l0 R-9 Ll03 J-S R13 C-6 R77 F-6 R20S 0-9 R324 L-ll R72S P-2 ZD702 R-4
CllO K-3 C2l7 L-8 C70l Q-6 0701 R-5 Ll05 L-3 R14 D-6 R78 B-5 R206 K-7 R353 L-1O R727 0.2 ZD8l2 D-IO
~~_~ ·_· · · ~ ~·~ I__C..11Z____K_,.s_- ___C218--L~'L_ ~cro2-~R-4- ~DW3~R-3--~U06---!-8- -R-l-S-----D-6--R-7-9-----G-3-~-R209---H-1O--~--R3S6--M=lO__--R~1--0__3- ------I~---··- -----.---------------- ---J-
Cll3 K-4 C2l9 L-3 C703 R-S D80l D-12 Ll07 K-3 R16 D-6 R81 B-8 R210 0-10 R40l P-9 R787 N-3
Cll4 1-4 C220 R-14 C706 8-2 D802 B-13 LllO H-3 R17 D-6 R82 B-8 R2ll H-9 R403 M-8 R792 S-2
ens K-S C221 H-6 C708 R-2 D803 B-13 Llll 1-1 R18 0-5 R83 B-8 R212 H-9 R404 M-7 R800 e-n
Cll6 K-4 C222 R-14 C7l0 P-3 D804 E-12 L1l2 1-1 R19 C-9 R84 B-8 R2l3 1-9 R40S Q-8 R80l B-ll
C1l7 L-4 C223 0-6 C7ll 0-3 D805 a-n L1l3 1-1 R20 C-8 R8S D-3 R2l4 1-8 R406 M-6 R802 a-u
C1l8 L-4 C224 H-7 C713 0-1 D806 1-12 L1l4 1-2 R21 C-8 R87 0-3 R2lS 1-7 R407 Q-9 R803 1-11
C1l9 L-4 C225 0-6 C721 0-2 D807 1-13 L200 H-9 R22 C-7 R89 F-8 R217 0-8 R409 1-10 R804 1-12
Cl20 L-4 C226 0-6 C745 P-3 D808 1-14 L201 H-8 R23 C-9 ROO B-8 R2l8 L-7 R4l0 H-1O asu 0-10
Page 3 SET 3541
MAIN BOARD, GRIDTRACE LOCATION GUIDE
I
II
i
! .
I
I.
I
SET 3541 Page 3
PARTS LIST continued
41 FR317 .47 S% lW Fusible ORF04701607 41 DYOI (1) Yoke 100° IS3-3SSA 41 1'801 Fuse 131-033X 4Amp, 12SVAC, Slow Blow
41 FR416 1 S% 2W Fusible ORFOI0IK607 F2WlDO Hom l.46mH i 1'801 Fuse 0FM2001ASI2 lAmp, 12SV, Fast Acting
i FR417 .47 S% lW Fusible 0RF04701607 Vert 17.2mH i PI Line Cord 174-019M AC, Polarized
FR418 1.2S%2WFusible ORF0121K607 F2WID2 FB301 Ferrite Bead 12S-123A PAl Preamp 106-047B Remote (SBXI620-72)
41 FR41' .47 S% 112W Fusible 0RF0470H609 FB410 IpH Ferrite Bead 12S-022K PH lack 401-734E Assembly
FR420 .47 S% 112WFusibie 0RF0470H609 FBSOl, 02, 03 Ferrite Bead 12S-123A i RLSOI Relay 141-018C Power
41 FR703 1 S% lW Fusible ORFOI011607 FIWlDO FB801 IpH Ferrite Bead 12S-022K SPI Speaker 12O-C93F 2" X 3 112",8 Obms, SW
FR801 .47 S% 112WFusibie 0RF0470H609 FB802 Ferrite Bead 12S-123A SWI Switch 14O-333B Power
41 FR805 .27 S% lW Fusible ORN02701607 Ll loopH OLAlOOOKl19 SW2 Switch 14O ... 333B Channel Up
41 FR806 .47 S% lW Fusible 0RF04701607 L2 OSD IS0-489V SW3 Switch 14O-333B Channel Down C)
R72 ISK 1% 1/6W ORNIS02F409 - L3 . loopH OLAlOOOK1l9 SW4 Switch 14O-333B Volume Up .~. .. ,
'~'~4~'10~M 101J,2W_~_~~~ •..... ~ .. JJID,,7&3E ··~~~~W:S_A7 •. ~._~~ .~.~ •. ~~~· ~ ... ~~ .• ~ .. ~ .• ~- .. _. ~ •• ~ ·~·~~cl,1~4a~~·~-2~~--~·~~-~-S~~i:~--··~·· .. ~ ... ~~ ... ---~.-~.~.~.~---~ .. _. ~~gW~·-~--SWl'teli~·~~····~·~·i«)';SSS·;r·~· ··~·YoiUiiiC fN'Wii-~-·~-·-··-~·~· ~~·~~~·~·~-C······I-
R800 1800 S% 7W Wirewound 180-830E L14 220pH 0LA2200K1l9 SW6 Switch 14O-333B Function en
41 R801 lS% 10WWirewound 180-822A 10W1DO LI02 .79pH IS0-167E SW301 Switch 140-111A Vertical Centering i!
i R801 1l0KS% 112W ORDll03H609 HW411 LI03 1.2pH OLA0121K1l9 SWS01 Switch 140-111A NonnaIIService :D
R883 27 S% SW Wirewound 180-142G SW027 L10S,06 68pH OLA0682K1l9 i VOl CRT 20SS-V6S04B A63ADG2SX
R940 .68 S% 2WFusibie ORF0680K607 LI07 22pH OLA0222K1l9 CRT 112-812A A63ADG2SX
41 TH901 8.0 Cold PTC 163-007A LllO 12pH OLA0122KI39 Xl Crystal 166"23SB 12MHz
VR204 10K RF AGe ORV1103D230 LIII Thru X401 Crystal 166-01SN S03kHz
VR232 2000 Sub Brightness ORVI202D230 L1l4 lSpH OLAOlS2K1l9 XS01 Crystal IS6-001C 3.S8MHz
VR316 10K Vertical Size ORVll03D230 L200 47pH OLA0472Kll9 Z101 FIlter 166-234A SAW
1000 Vertical Size L201 lSpH OLAOIS2K1l9 Z102 Ftlter 166-003D 4.SMHz
10K Horizontal Centering ORVll03D230 L203 loopH OLA1000K139 Z103 Trap 166-0311 4.SMHz
2000 External Video Level ORV1202D230 L206 68pH OLA0682KI39 Adapter 4So-oo3A Antenna 7S To 300 Obms
20KExternal Audio Level ORV1203D230 L221 SIP ISO-S40Z PC Board (I) 401-734E Antenna
330 Red Drive L222 AFT lS0-916A PC Board (1) llO-XI9L CRT
300 Red Drive ORVI30ID230 L223 VCO ISO-S4OT PC Board (I) llO-X19l CRT
VR912 4700 Red Bias • IA01 Horizontal Linearity lSO-716L PC Board (1) 109-279A Main
SOOO Red Bias ORV1S02D230 L403 8.2mH IS0-892A Shield Box 401-068M Antenna
VR922 4700 Green Bias L40S 270pH 0LA27ooK139 • Socket 381-226D CRT
SOOO Green Bias ORV1S02D230 L701 22pH OLA0222K1l9 Transmitter 10S-207C Remote
VR931 330 Blue Drive L801 loopH ISO-23SC Tuner (1) ll3-202T UHFNHF
300 Blue Drive ORVl30ID230 41 L901 Degaussing ISO-DOSH
VR932 4700 Blue Bias L911, 21, 31 120pH OLA1200K139
SOOO Blue Bias ORVlS02D230 T401 Horizontal Driver ISI-060A
T402 (1) Horizontal Output lS4-106D
41 T701 Power ISO-ISlA
41 T801 Line Filter ISO-ISlA
41 T801 Power ISI-340D
CONTROLS & RESISTORS
NTEPartNo.
Item No, FunctlonlRating
Mfr. Part No.
COILS & TRANSFORMERS
Mfr. Part No.
Item No.
FunctionlRatlng
MISCELLANEOUS
Item No. Description
Mfr. Part No. Notea
VR431 VR7S1 VR7S3 VR9ll
i For SAFETY use only equivalent replacement part.
(1) Contact PTS Electronics Corporation for replacement; order by manufacturer's part number.
i For SAFETY use only equivalent replacement part.
(') Z N CD
!
!
•
r .
i
41 For SAFETY use only equivalent replacement part. (1) Focus and screen controls are part of T402.
I
Page 4 SET 3541
SET 3541
Page 4