The PICNIC TABLE and bench standards shall be made up of galvanized and powder coatd steel tubular supports and channel seat and table frames. TGIC-polyester shall be applied at a film thickness of 3 to 4 mils by electrostatic spray process and bake fmished per manufacturer's directions.
The PICNIC TABLE and bench standards shall be made up of galvanized and powder coatd steel tubular supports and channel seat and table frames. TGIC-polyester shall be applied at a film thickness of 3 to 4 mils by electrostatic spray process and bake fmished per manufacturer's directions.
The PICNIC TABLE and bench standards shall be made up of galvanized and powder coatd steel tubular supports and channel seat and table frames. TGIC-polyester shall be applied at a film thickness of 3 to 4 mils by electrostatic spray process and bake fmished per manufacturer's directions.
The PICNIC TABLE and bench standards shall be made up of galvanized and powder coatd steel tubular supports and channel seat and table frames. TGIC-polyester shall be applied at a film thickness of 3 to 4 mils by electrostatic spray process and bake fmished per manufacturer's directions.
MATERIALS:,
CONCRETE: Shall be either average conerete pi bs,
SONCRETE: Salles piers or concrete slabs, as shown on the plans and as
STANDARDS: The picnic table and bench standards shall be made up of galvanized and powder
Coated steel tubular supports and channel seat and table frames as manufactured by All City Play
Equipment, Brooklyn, NY or A & T Iron Works Corp., New Rochelle, NY, or approved equal, The
tubular supports shall be provided with base angles. The steel tubular supports shall be continuously
welded to the channel and the base angle as indicated on the plans. The standards shall be hot-
dipped galvanized and powder coated after fabrication.
Powder Coating: The galvanized picnic table and bench set standards shall be powder coated
with a polyester thermosetting powder coating such as manufactured by Tiger Drylac USA,
Reading, PA. Color to be gloss black, RAL-8022 or approved equal.
Galvanizing of standards shall provide an acceptable substrate for applied powder coatings. No
lacquer, urethane or other coatings which would prevent proper adhesion of powder coating shall
be applied to the steel.
‘The powder-coating shall be applied to the galvanized standards in such a manner that the
coating will not peel off. Insure surfaces to be coated are clean and dry and free of grease, dust,
rust, etc. All coated parts shall firstreceive phosphating and chromatizing treatments to improve
the adhesion of the surface coating. 5
‘The TGIC-Polyester shall be applied at a film thickness of 3 to 4 mils by electrostatic spray
process and bake finished per manufacturer's directions. The TGIC-Polyester shall be applied
without yoids, tears or cuts that reveal the substrate and shall thoroughly adhere to the metal
without peeling when scratched with a pick device or knife blade point.
‘Touch-up & Repair: For minor damaged caused by installation or transportation, clean damaged
area, then; . . .
1. On damaged galvanized surfaces, apply organic zinc repair paint complying with
ASTM A780, then repair powder coating per number 2 below. Galvanizing repair
paint shall have 65 percent zinc by weight. Thickness of repair paint shall be not ess
‘than that required by ASTM A123.
2. On damaged powder coated surfaces, touch-up finish in conformance with
manufacturer's recommendations. Provide touch-up such that repair is not visible
“4
335from a distance of six feet (69.
LUMBER: All slats for table and benches shall not absorb ‘moisture, corrode, rot, warp, splinter, or
crack and shall not contain fiberglass or any material that will be irritating when in contact to the
skin,
Fabrication Tolerances: Ends shall be smooth with clean cuts, cross-sections shall not have
Voids greater than %" dia, Voids of %" dia. or less shall be filled az Per manufacturer's
Specifications. All edges shall be eased. Maximum variation from flat surface across section
shall be 1/8",
Delivery and Storage: Keep materials protected at all times against exposure to extreme heat or
impact. All material shall be bundled and fully supported during shipping and storage o prevent
creep. /Any lumber that is damaged or excessively scratched will be rejected and replaced with
new. All material must be straight and true when placed in the construction,
All slats for table and benches shall be fabricated from ONE of the following:
A: Recycled Plastic Lumber: At least eighty (80%) percent shall post-consumer recycled plastic,
Pending passing test results and submittal of same, recycled plastic lumber shall be as
manufactured by Seaward, Inc. Clearbrook, VA, Polywood, Inc., Edison, NJ, or approved
equal, Color to be DARK GRAY or BROWN unless otherwise indicated on the plans, ‘Submit
sample for approval. :
Manufacturing of Recycled Plastic Lumber shall comply with or be tested in accordance with
Provisions of the following as applicable to the performance of the work:
ASTM 6108-97 _ Standard Test Method for Compressive Products of Plastic and
Shapes. :
ASTM D6109-97 Standard Test Method for Flexural Properties of Unreinforced and
Reinforced Plastic Lumber.
ASTMD6111-97 Standard Test Method for Bulk Density and Specific Gravity of
Plastic, ‘Lumber and Shapes by Displacement.
ASTM D6112-97 Standard Test Method for Compressive and Flexural Creep and Creep
Rupture of Plastic Lumber and Shapes.
ASTM D6117-97 Standard Test Method for Mechanical Fasteners in Plastic Lumber and
Shapes.
ASTM 1248 Standard Specifications for Polyethylene Plastics,
Recycled Plastic Lumber shall be fabricated primarily from High Density Polyethylene (HDPE)
and Low Density Polyethylene (LDPE) recycled polycthylene. HDPE resins shall mect
us
396requirements of ASTM D1248 for Type III or IV (high density), Grade G7. Material shall
contain no toxic materials. Recycled Plastic Lumber shall contain UV-inhibited pigment,
Composition and mechanical properties shall be as follows:
Minimum Recycled Content 90%
Minimum High Density Polyethylene 10%
Maximum percentage of materials other than polyolefins 5%
Minimum Density (ASTM D6111) 45 lb/ft
‘Minimum Strength and Stiffness: Platwise Edgewise
Minimum Ultimate Flexural Strength
(ASTM D6109) ({b-in) 2,500 5,800
Minimum Flexural Stiffness
(ASTM D6109) (Ib-in’) 85,000 450,000
Flame Spread, Class C or better, tested in accordance with ASTM E84,
Coefficient of Thermal Expansion, in the range of -10°C to 30°C, shall not exceed 60 x 10°F,
Creep performance data (time dependent stress/strain characteristics) shall be submitted in
accordance with ASTM D6112.
HARDWARE: All hardware shall be stainless steel. Slats shall be attached to bench standards with
3/8" dia, carriage bolts with 3/8" lock washer and 3/8" nut. Ends of bolts shall be pened,
INSTALLATION: The standards shall be set in concrete with supports vertical and true to line and
Position as shown on the plans or as directed by the Engineer.
The slats shall be secured to the channel frames with vandalproof bolts of 18-8 stainless steel as
indicated on the plans or approved equal. Ends of all bolts shall be pened and filed smooth after
tightening,
‘SUBMITTALS: All submittals shall be submitted prior to manufacture and in accordance with the
requirements of the General Conditions, Section C, Special Provisions, Article 11.
Recycled Plastic Lumber: The following tests shall be provided:
1. ASTM D6108 - Compression Properties
ASTM D6109 - Flexural Properties
ASTM D611] - Density tests
ASTM D6112 - Creep tests
‘ASTM D6117 - Mechanical Fasteners
ASTM D1248 - Standard Specifications for Polyethylene Plastics
ASTM E84 - Flame Spread
AayaLN
34
337Laboratory Test For TGIC-Polyester Powder Coat: At the discretion of the Engineer, a sample
‘TGIC-Polyester powder coated standard shall be laboratory tested for bonding of the powder coating
to the metal, Test shall be the Cross Hatch test per ASTMD3359, Method B. Failure to satisfactorily
pass this test shall be a basis for rejection.
PAY ': The quantity of PICNIC TABLE -FIXED and PICNIC
TABLE -FIXED/ACCESSIBLE to be paid for under these items shall be the number of units
furnished and installed in accordance with the plans, specifications and directions of the Engineer
The price bid shall be a unit price for EACH Picnic Table -Fixed And Picnic Table -
Fixed/Accessible and shall include the cost of all labor, materials and equipment including benches,
steel standards and frames, plastic lumber, hardware, and powder coating and all incidental expenses
necessary to complete the work in accordance with the plans and specifications to the satisfaction of
the Engineer
Conerete pier or slab shall be paid under the item “Average Concrete”. Foundation Material, where
required, shall be paid for under the item “Foundation Material For Concrete”. Excavation shall be
paid for under the item “Unclassified Excavation”.
END OF PAGE
Rev 04/13/2005
338CONTRACT NUMBER-0G-1608A a
ITEM DESCRIPTION Unit Price: Total Bid Price
in Figures laty X Uni
Price in Figures
STEEL EDGING
LINEAR FOOT
GRANITE BLOCK LANDSCAPE EDGING
LINEAR FOOT
RECONSTRUCT CONCRETE CURB
JLINEAR FOOT
BICYCLE RACK
11. | CONCRETE GAME TABLE
ff
BENCH, 1964 WORLD'S FAIR WIRPL SLATS - ARMLESS *
LINEAR FOOT
BENCH, 1964 WORLD'S FAIR WIRPL SLATS & ARMS *
LINEAR FOOT
METAL SHADE STRUCTURE *