Professional Documents
Culture Documents
GSM (SMS) Controlled DC Motor
GSM (SMS) Controlled DC Motor
GSM (SMS) Controlled DC Motor
com/fyp/
INTRODUCTION
GSM (SMS) Controlled DC Motor is automatic control system which capable of receiving a set
of command instructions in the form of Short message service and performs the necessary actions
like Start , Stop and speed control. We will be using a dedicated modem/mobile at the receiver
module i.e. with the robot it self and send the commands using SMS service as per the required
actions.
The mobile unit which is dedicated at the motor driver is interfaced with an intellectual
device called Micro controller so that it takes the responsibility of reading the received
commands in the form of SMS from the mobile unit and perform the corresponding predefined
tasks such as motor start, stop, motor direction and speed control at different levels etc.
HARDWARE USED
SOFTWARE USED
THEORY OF OPERATION
Final Year Project's is One place for all Engineering Projects, Presentation, seminar,
summer training report and lot more.
NOTE:-This work is copyright to its Authors. This is only for Educational Purpose.
http://www.final-yearprojects.co.cc/ http://troubleshoot4free.com/fyp/
In this project we interfaced 8051 microcontroller with Motorola’s C168 GSM mobile phone to
decode the received message and do the required action. The protocol used for the
communication between the two is AT command.
The microcontroller continuously checks for SMS to take the decision for controlling the DC
motor.
AT-Command set
The following section describes the AT-Command set. The commands can be tried out by
connecting a GSM modem to one of the PC’s COM ports. Type in the test-command,
adding CR + LF (Carriage return + Line feed = \r\n) before executing. Table gives an
overview of the implemented AT-Commands in this application. The use of the
commands is described in the later sections.
Command Description
Check if serial interface and GSM modem is
AT working.
ATE0 Turn echo off, less traffic on serial line.
AT+CNMI Display of new incoming SMS.
AT+CPMS Selection of SMS memory.
AT+CMGF SMS string format, how they are compressed.
Read new message from a given memory
AT+CMGR location.
AT+CMGS Send message to a given recipient.
AT+CMGD Delete message.
A microcontroller is a single chip that contains the processor (the CPU), non-
volatile memory for the program (ROM or flash), volatile memory for input and output
(RAM), a clock and an I/O control unit. Also called a "computer on a chip," billions of
microcontroller units (MCUs) are embedded each year in a myriad of products from toys
Final Year Project's is One place for all Engineering Projects, Presentation, seminar,
summer training report and lot more.
NOTE:-This work is copyright to its Authors. This is only for Educational Purpose.
http://www.final-yearprojects.co.cc/ http://troubleshoot4free.com/fyp/
Final Year Project's is One place for all Engineering Projects, Presentation, seminar,
summer training report and lot more.
NOTE:-This work is copyright to its Authors. This is only for Educational Purpose.
http://www.final-yearprojects.co.cc/ http://troubleshoot4free.com/fyp/
The hardware is driven by a set of program instructions, or software. Once familiar with
hardware and software, the user can then apply the microcontroller to the problems
easily.
The pin diagram of the 8051 shows all of the input/output pins unique to
microcontrollers:
Final Year Project's is One place for all Engineering Projects, Presentation, seminar,
summer training report and lot more.
NOTE:-This work is copyright to its Authors. This is only for Educational Purpose.
http://www.final-yearprojects.co.cc/ http://troubleshoot4free.com/fyp/
Final Year Project's is One place for all Engineering Projects, Presentation, seminar,
summer training report and lot more.
NOTE:-This work is copyright to its Authors. This is only for Educational Purpose.
http://www.final-yearprojects.co.cc/ http://troubleshoot4free.com/fyp/
BLOCK DIAGRAM
L293
DC MOTOR
PORT1
8051
Level
Convert
er
Final Year Project's is One place for all Engineering Projects, Presentation, seminar,
summer training report and lot more.
NOTE:-This work is copyright to its Authors. This is only for Educational Purpose.