Professional Documents
Culture Documents
BOP Operations Maintenance
BOP Operations Maintenance
U BLOWOUT PREVENTERS
FOR SURFACE APPLICATIONS
All the information contained in this manual is the exclusive property of
Cooper Cameron Corporation, Cameron Division. Any reproduction or use
of the calculations, drawings, photographs, procedures or instructions,
either expressed or implied, is forbidden without the written permission of
Cameron or its authorized agent.
Initial Release A1
March 1999
TC1403 2
PREFACE
The procedures included in this book are to be performed in conjunction with
the requirements and recommendations outlined in API Specifications. Any re-
pairs to the equipment covered by this book should be done by an authorized
Cameron service representative. Cameron will not be responsible for loss or ex-
pense resulting from any failure of equipment or any damage to any property or
injury or death to any person resulting in whole or in part from repairs per-
formed by other than authorized Cameron personnel. Such unauthorized re-
pairs shall also serve to terminate any contractual or other warranty, if any, on
the equipment and may also result in equipment no longer meeting applicable
requirements.
File copies of this manual are maintained. Revisions and/or additions will be
made as deemed necessary by Cameron. The drawings in this book are not
drawn to scale, but the dimensions shown are accurate.
This book covers Cameron U Blowout Preventers, which are products of Cooper
Cameron Corporation.
TC1403 3
Contents
Single Open-Face Flange or Clamp Hub Dimensions . . . . . . . . . . . 6
Double Open-Face Flange or Clamp Hub Dimensions. . . . . . . . . . . 8
Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Hydraulic Control System . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Specifications and Accessories . . . . . . . . . . . . . . . . . . . . . . . 18
Large Bore Shear Bonnets . . . . . . . . . . . . . . . . . . . . . . . . . 19
Tandem Boosters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Ram Hang-Off Weights and Shear Requirements . . . . . . . . . . . . . 21
Pipe Rams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Shearing Blind Rams . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DSI and DVS Shear Rams . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Variable Bore Rams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Flexpackers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
CAMRAM™ 350 Packers and Top Seals . . . . . . . . . . . . . . . . . . 34
Rams for Multiple Completions . . . . . . . . . . . . . . . . . . . . . . 35
Bonnet Rebuild Softgoods Kits . . . . . . . . . . . . . . . . . . . . . . . 36
Bonnet Seals and Connecting Rod Seals . . . . . . . . . . . . . . . . . . 38
Bonnet Seal Carriers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
U BOP Operation and Maintenance . . . . . . . . . . . . . . . . . . . . 40
I. Physical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
II. Applicable Operating Characteristics . . . . . . . . . . . . . . . . 42
III. Disassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . 43
IV. Assembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . 45
V. Operation and Installation Procedures . . . . . . . . . . . . . . . 48
VI. Maintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . 49
VII. Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
VIII. Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Bonnet Bolt Torque Requirements . . . . . . . . . . . . . . . . . . . . . 54
TC1403 5
The capital letters in the following designations refer to the U BOP dimensional views below and dimensional charts shown on the following page.
A-1 Length - bonnets closed, locking screws locked D Centerline of preventer to outlet flange or hub face. This distance is variable
A-2 Length - bonnets opened, locking screws unlocked and must be determined per individual specifications.
A-3 Length - bonnets closed, with wedgelocks E-1 Centerline of side outlet to bottom flange face
A-4 Length - bonnets opened, with wedgelocks E-2 Centerline of side outlet to bottom hub face
B-1 Height - flanged F-1 Top of ram to top flange face
B-2 Height - clamp hubs F-2 Top of ram to top hub face
C Width - no side outlets G Height of ram
OPEN
B G
Single U BOP
SD-017499
TC1403 6
Single Open-Face Flange or Clamp Hub U BOP Dimensions*
Pressure Vertical Approx.
Size A-1 A-2 A-3 A-4 B-1 B-2 C E-1 E-2 F-1 F-2 G
Rating Bore Weight
(in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.)
(psi) (in.) (lb)
7-1/16** 3000 7-1/16 74.000 109.500 - - 24.062 - 20.250 8.750 - 7.844 - 5.50 2600
7-1/16** 5000 7-1/16 74.000 109.500 - - 27.500 25.188 20.250 10.406 9.250 9.625 8.469 5.50 2800
7-1/16 10,000 7-1/16 74.000 109.500 - - 30.562 27.188 20.625 11.062 9.375 12.031 10.344 5.50 3550
7-1/16 15,000 7-1/16 74.000 109.500 - - 31.812 - 20.625 11.688 - 12.656 - 5.50 3800
11** 3000 11 96.250 146.875 - - 29.062 - 25.125 9.812 - 10.531 - 6.75 5300
11** 5000 11 96.250 146.875 110.125 150.188 34.312 29.312 25.125 12.438 9.938 13.156 10.656 6.75 5600
11** 10,000 11 96.250 146.875 110.125 150.188 35.688 32.188 25.750 13.125 11.375 13.844 12.094 6.75 6400
11 Model 79 15,000 11 124.000 175.312 124.500 167.125 44.812 33.875 32.000 16.688 11.219 17.781 12.312 9.25 10,300
13-5/8 3000 13-5/8 112.125 171.500 122.688 166.062 31.312 - 29.250 10.312 - 11.531 - 7.50 7200
13-5/8 5000 13-5/8 112.125 171.500 122.688 166.062 33.812 31.938 29.250 11.562 10.625 12.781 11.844 7.50 7700
13-5/8 10,000 13-5/8 114.125 172.750 124.688 167.312 41.688 32.812 30.250 15.125 10.688 17.094 12.656 7.50 10,300
13-5/8 Model B** 15,000 13-5/8 139.000 214.375 152.250 205.500 53.688 42.000 39.500 21.375 15.500 22.844 17.000 8.00 23,700
16-3/4” Model B 3000 16-3/4 127.250 204.562 147.250 199.375 40.062 31.750 35.750 13.312 9.156 15.406 11.250 9.25 13,700
16-3/4 Model B 5000 16-3/4 129.250 202.125 149.250 202.250 43.062 34.938 35.750 14.812 10.750 16.906 12.844 9.25 13,750
16-3/4** 10,000 16-3/4 139.000 218.375 155.500 212.000 49.688 41.938 39.500 19.375 15.500 20.219 16.344 9.25 23,300
18-3/4 10,000 18-3/4 156.375 242.125 166.500 226.625 56.000 43.234 42.500 20.500 13.875 22.000 15.344 12.00 28,900
20-3/4 3000 20-3/4 143.688 226.812 163.938 223.875 40.562 33.312 39.516 14.312 10.688 16.281 12.656 8.00 13,650
21-1/4 2000 21-1/4 143.688 226.812 163.938 223.875 37.188 33.312 39.516 12.625 10.688 14.594 12.656 8.00 13,250
21-1/4 5000 21-1/4 164.250 247.250 180.938 239.250 50.938 46.125 42.500 17.969 17.188 18.719 14.688 13.50 30,000
21-1/4** 10,000 21-1/4 163.375 250.375 181.125 239.500 66.000 53.000 47.250 24.531 18.031 26.250 19.750 13.50 34,650
26-3/4 3000 26-3/4 169.625 275.375 - - 48.312 - 46.250 17.438 - 19.906 - 8.00 24,000
TC1403 7
The capital letters in the following designations refer to the U BOP dimensional views below and dimensional charts shown on the following page.
A-1 Length - bonnets closed, locking screws locked E-1 C enterline of side outlet below rams to bottom flange face
A-2 Length - bonnets opened, locking screws unlocked E-2 Centerline of side outlet below rams to bottom hub face
A-3 Length - bonnets closed, with wedgelocks F-1 Top of upper ram to top flange face
A-4 Length - bonnets opened, with wedgelocks F-2 Top of upper ram to top hub face
B-1 Height - flanged G Height of ram
B-2 Height - clamp hubs H-1 Centerline of side outlet between rams to bottom flange face
C Width - no side outlets H-2 Centerline of side outlet between rams to bottom hub face
D Centerline of preventer to outlet flange or hub face. This distance J Top of lower ram to bottom of upper ram
is variable and must be determined per individual specifications.
OPEN
G
B J
OPEN
G H
Double U BOP
SD-017498
TC1403 8
Double Open-Face Flange or Clamp Hub U BOP Dimensions*
Press. Vert. Approx.
Size A-1 A-2 A-3 A-4 B-1 B-2 B*** C E-1 E-2 F-1 F-2 G H-1 H-2 J
Rating Bore Weight
(in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.)
(psi) (in.) (lb)
7-1/16** 3000 7-1/16 74.000 109.500 - - 41.00 - 18.562 20.250 8.750 - 7.844 - 5.50 25.688 - 11.438 5000
7-1/16** 5000 7-1/16 74.000 109.500 - - 44.188 41.875 18.812 20.250 10.406 9.250 9.625 8.469 5.50 27.094 25.938 11.188 5200
7-1/16 10,000 7-1/16 74.000 109.500 - - 48.625 45.250 17.438 20.625 11.062 9.375 12.031 10.344 5.50 29.125 27.438 12.562 6400
7-1/16 15,000 7-1/16 74.000 109.500 - - 49.875 - 17.438 20.625 11.688 - 12.656 - 5.50 29.750 - 12.562 6750
11** 3000 11 96.250 146.875 - - 49.250 - 16.562 25.125 9.812 - 10.531 - 6.75 30.000 - 13.438 9900
11** 5000 11 96.250 146.875 110.125 150.188 54.500 49.500 16.562 25.125 12.438 9.938 13.156 10.656 6.75 32.625 30.125 13.438 10,200
11** 10,000 11 96.250 146.875 110.125 150.188 55.875 52.375 16.562 25.750 13.125 11.375 13.844 12.094 6.75 33.312 31.562 13.438 11,300
11 Model 79 15,000 11 124.000 175.312 124.500 167.125 69.750 58.812 14.312 32.000 16.688 11.219 17.781 12.312 9.25 41.625 36.156 15.688 18,400
13-5/8 3000 13-5/8 112.125 171.500 122.688 166.062 53.375 - 15.438 29.250 10.312 - 11.531 - 7.50 32.375 - 14.562 14,300
13-5/8 5000 13-5/8 112.125 171.500 122.688 166.062 55.875 54.000 15.438 29.250 11.562 10.625 12.781 11.844 7.50 33.625 32.688 14.562 14,800
13-5/8 10,000 13-5/8 114.125 172.750 124.688 167.312 66.625 57.750 12.562 30.250 15.125 10.688 17.094 12.656 7.50 40.062 35.625 17.438 18,400
13-5/8 Mod B** 15,000 13-5/8 139.000 214.375 152.250 205.500 81.750 70.125 9.938 39.500 21.375 15.500 22.844 17.000 8.00 49.438 43.562 20.062 43,250
16-3/4” Mod B 3000 16-3/4 127.250 204.562 147.250 199.375 65.875 57.562 13.438 35.750 13.312 9.156 15.406 11.250 9.25 39.125 34.969 16.562 26,650
16-3/4 Mod B 5000 16-3/4 129.250 202.125 149.250 202.250 68.875 60.750 13.438 35.750 14.812 10.750 16.906 12.844 9.25 40.625 36.562 16.562 26,940
16-3/4** 10,000 16-3/4 139.000 218.375 155.500 212.000 77.750 70.000 11.188 39.500 19.375 15.500 20.219 16.344 9.25 47.438 43.562 18.812 43,500
18-3/4 10,000 18-3/4 156.375 242.125 166.500 226.625 87.125 74.000 10.875 42.500 20.500 13.875 22.000 15.344 12.00 51.500 44.875 19.125 56,950
20-3/4 3000 20-3/4 143.688 226.812 163.938 223.875 66.125 58.875 12.438 39.516 14.312 10.688 16.281 12.656 8.00 39.875 36.250 17.562 25,550
21-1/4 2000 21-1/4 143.688 226.812 163.938 223.875 62.750 58.875 12.438 39.516 12.625 10.688 14.594 12.656 8.00 38.188 36.250 17.562 25,150
21-1/4 5000 21-1/4 164.250 247.250 180.938 239.250 82.375 74.000 12.375 42.500 17.969 17.188 18.719 14.688 13.50 49.031 45.000 17.625 58,000
21-1/4** 10,000 21-1/4 163.375 250.375 181.125 239.500 100.062 87.062 9.438 47.250 24.531 18.031 26.250 19.750 13.50 58.594 52.094 20.562 65,500
26-3/4 3000 26-3/4 169.625 275.375 - - 78.875 - 7.438 46.250 17.438 - 19.906 - 8.00 48.000 - 22.562 44,200
TC1403 9
35
17
16
15
2
24
6
11
29
42
10
38
36
37
34
12
28
27
30
31
32
24
26
5
9
33
3
13
8
7
14
22
41
40
21
19
18
20
23
25
Double U BOP
SD-017500
TC1403 10
7-1/16” 3000 - 11” 10,000 psi WP U BOP Part Numbers
7-1/16” 7-1/16” 7-1/16” 7-1/16” 11” 11” 11”
Item Qty Qty 3000 5000 10,000 15,000 3000 5000 10,000
Description
No. Sgl Dbl psi psi psi psi psi psi psi
Model II Model II Model II Model II Model II Model II Model II
1 Body 1 1 - - - - - - -
2 Intermediate Flange 2 4 30266-03 30266-03 30266-01 30266-01 30267-03 30267-03 30267-03
2A Intermediate Flange/Shear - - 41499-03** 41499-03** 41499-01** 41499-01** 41457-03** 41457-03** 41457-03**
3 Bonnet 2 4 30278-04 30278-03 30278-02 30278-01 30268-01 30268-02 30268-03
4 Ram Assembly 2 4 644216-( ) 644216-( ) 644216-( ) 644216-( ) 644219-( ) 644219-( ) 644219-( )
5 Piston, Operating 2 4 236501-15-11-08 236501-15-11-08 236501-15-11-08 236501-15-11-08 673178 163192-01 163192-01
5A Piston, Operating/Shear - - 49116-01** 49116-01** 49116-01** 49116-01** 698914** 698914** 698914**
6 Cylinder, Operating 2 4 30274-02 30274-02 30274-02 30274-02 30274-03 30274-03 30274-03
6A Cylinder, Operating/Shear - - 41365-02 41365-02 41365-02 41365-02 41365-03** 41365-03** 41365-03**
7 Housing, Locking Screw 2 4 30308-01 30308-01 30308-01 30308-01 30308-02 30308-02 30308-02
8 Locking Screw 2 4 30326 30326 30326 30326 30365 30365 30365
8A Locking Screw/Shear - - 49258-01 49258-01 49258-01 49258-01 46628-01 46628-01 46628-01
9 Piston, Ram Change/Open 2 4 30324 30324 30324 30324 30362 30362 30362
10 Piston, Ram Change/Close 2 4 30325 30325 30325 30325 30363 30363 30363
11 Cylinder, Ram Change 4 8 30273-02 30273-02 30273-02 30273-02 30273-03 30273-03 30273-03
12 Bolt, Bonnet 8 16 30312-06 30312-02 30312-07 30312-01 30312-04 30312-03 30312-05
12A Bolt, Bonnet/Shear - - 41366-06 41366-02 41366-07 41366-22 41366-04 41366-03 41366-05
13 Stud, Locking Screw Housing 16 32 219065-10-04-41 219065-10-04-41 219065-10-04-41 5913-26-10 5915-25-10 219065-12-05-01 219065-12-05-01
13A Stud, Locking Screw Housing/Shear - - 38732-57-00-54 38732-57-00-54 38732-57-00-54 38732-57-00-54 38732-59-00-65 38732-59-00-65 38732-59-00-65
14 Nut, Locking Screw Housing 16 32 2709000-10-01 2709000-10-01 2709000-10-01 2709000-10-01 2709000-12-01 2709000-12-01 2709000-12-01
15 Check Valve, Plastic Packing 2 4 M517988 M517988 M517988 M517988 M517988 M517988 M517988
16 Screw, Plastic Packing 2 4 5940-09 5940-09 5940-09 5940-09 5940-09 5940-09 5940-09
17 Pipe Plug, Plastic Packing 2 4 005930-05-10 005930-05-10 005930-05-10 005930-05-10 005930-05-10 005930-05-10 005930-05-10
18 Ring, Plastic Packing 2 4 12469-36 12469-36 12469-36 12469-36 12469-38 12469-38 12469-38
19 Ring, Plastic Energizing 2 4 18586-12 18586-12 18586-12 18586-12 18586-13 18586-13 18586-13
20 Seal Ring, Connecting Rod 2 4 212741-37-00-01 212741-37-00-01 212741-37-00-01 212741-37-00-01 212741-38-00-01 212741-38-00-01 212741-38-00-01
21 Ring Back-Up 4 8 - - 21792-21 21792-21 21792-22 21792-22 21792-22
22 Seal, Bonnet 2 4 644197-01-00-01 644197-01-00-01 644197-01-00-01 644197-01-00-01 644197-02-00-01 644197-02-00-01 644197-02-00-01
23 Pin, Ram Guide 4 8 30313-02 30313-02 30313-02 30313-02 30313-03 30313-03 30313-03
24 O-Ring, Operating Cylinder 4 8 702640-44-61 702640-44-61 702640-44-61 702640-44-61 702640-45-11 702640-45-11 702640-45-11
25 O-Ring, Operating Piston Rod to Int Flg 2 4 18492-92 18492-92 18492-92 18492-92 18492-91 18492-91 18492-91
26 Lip Seal, Operating Piston 2 4 710541 710541 710541 710541 710539 710539 710539
27 Seal Ring, Tail Rod 2 4 212741-32 212741-32 11741-32 11741-32 212741-33-00-01 212741-33-00-01 212741-33-00-01
28 O-Ring, Wiping 2 4 702640-33-11 702640-33-11 702640-33-11 702640-33-11 702640-33-51 702640-33-51 702640-33-51
29 O-Ring, Ram Change Piston to Body 4 8 702640-32-41 702640-32-41 702640-32-41 702640-32-41 702640-32-61 702640-32-61 702640-32-61
30 O-Ring, Ram Change Piston Rod to Int Flg 4 8 702640-32-91 702640-32-91 702640-32-91 702640-32-91 702640-33-11 702640-33-11 702640-33-11
31 O-Ring, Ram Change Cylinder to Int Flg 4 8 702640-33-81 702640-33-81 702640-33-81 702640-33-81 31423-25-13-85 31423-25-13-85 31423-25-13-85
32 O-Ring, Ram Change Cylinder to Bonnet 4 8 702640-34-21 702640-34-21 702640-34-21 702640-34-21 2010180-02 31423-26-13-85 31423-26-13-85
33 O-Ring, Ram Change Piston 4 8 702640-33-21 702640-33-21 702640-33-21 702640-33-21 702640-33-51 702640-33-51 702640-33-51
34 O-Ring, Bonnet Bolt Retainer 8 16 702640-22-51 702640-22-51 702640-22-91 702640-23-21 702640-22-71 702640-22-91 702640-23-41
35 Cap Screw, Int Flange to Bonnet 16*** 32*** 702585-22-00-50 702585-22-00-50 702585-22-00-50 702585-22-00-50 702585-22-00-50 702585-22-00-50 702585-22-00-50
36 Gland, Bleeder 2 4 17454-08 17454-08 17454-08 17454-08 17454-08 17454-08 17454-08
37 Plug, Bleeder 2 4 17454-09 17454-09 17454-09 17454-09 17454-09 17454-09 17454-09
38 Lifting Eye 2 2 11849 11849 11849 11849 11849 11849 11849
39 Packing, Plastic 10 20 7650-25 7650-25 7650-08 7650-08 7650-08 7650-25 7650-25
40 Washer 2 4 689523-04 689523-04 689523-04 689523-04 689523-05 689523-02 689523-02
41 Ring, Retainer 2 4 18572-83 18572-83 18572-83 18572-83 18572-84 18572-84 18572-84
42 Wear Ring, Operating Piston 2 4 49223-03 49223-03 49223-03 49223-03 49223-02 49223-02 49223-02
43 Spacer, Shear**** - - 687117-01 687117-01 687117-01 687117-01 687117-02 687117-02 687117-02
****A large bore shear bonnet is available for these sizes. For part numbers, see page 19.
****Part numbers shown are for old style shear bonnets. For current model large bore shear bonnet part numbers, see page 19.
****13-5/8” through 16-3/4” and 20-3/4” through 26-3/4” require 24 for single and 48 for double. The 18-3/4” requires 32 for single and 64 double.
****Required on all 11” 15,000 psi and 16-3/4” 10,000 psi BOPs with manual locking screws.
TC1403 11
35
17
16
15
2
24
6
11
29
42
10
38
36
37
34
12
28
27
30
31
32
24
26
5
9
33
3
13
8
7
14
22
41
40
21
19
18
20
23
25
Double U BOP
SD-017500
TC1403 12
11” 15,000 - 16-3/4” 5000 psi WP U BOP Part Numbers
11” 13-5/8” 13-5/8” 13-5/8” 13-5/8” 16-3/4” 16-3/4”
Item Qty Qty 15,000 3000 5000 10,000 15,000 3000 5000
Description
No. Sgl Dbl psi psi psi psi psi psi psi
Model 79 Model II Model II Model II Model B Model B Model B
1 Body 1 1 - - - - - - -
2 Intermediate Flange 2 4 49391-01 30270-01 30270-01 31216 698899 38944 38844
2A Intermediate Flange/Shear - - * 686242** 686242** 686767** * - 41408
3 Bonnet 2 4 31241 30284-02 30284-01 31241 691849 38843-02 38843-01
4 Ram Assembly 2 4 644222-( ) 644225-( ) 644225-( ) 644225-( ) 644228-( ) 644231-( ) 644231-( )
5 Piston, Operating 2 4 698481 236501-33-11-08 236501-33-11-08 678512-00-00-02 698996 614374-01 689562
5A Piston, Operating/Shear - - * 687542** 687542** 690791** * - 694085**
6 Cylinder, Operating 2 4 30274-01 30274-01 30274-01 30274-01 30274-06 30274-06 30274-06
6A Cylinder, Operating/Shear - - - 41365-01** 41365-01** 41365-01** - - 41365-06**
7 Housing, Locking Screw 2 4 30308-03 30308-03 30308-03 30308-03 30308-06 30308-06 30308-06
8 Locking Screw 2 4 30846 30307 30307 30307 695234 38901 38901
8A Locking Screw/Shear - - - 30846 30846 30846 - - 695234
9 Piston, Ram Change/Open 2 4 31239 30310 30310 31239 38847 38946 38847
10 Piston, Ram Change/Close 2 4 31238 30309 30309 31238 038848-01 38947 038848-01
11 Cylinder, Ram Change 4 8 30273-01 30273-01 30273-01 30273-01 30273-06 30273-07 30273-06
12 Bolt, Bonnet 8 16 30312-12 30312-09 30312-01 30312-12 30312-25 30312-17 30312-16
12A Bolt, Bonnet/Shear - - - 41366-09 41366-01 41366-12 - - 41366-16
13 Stud, Locking Screw Housing 16 32 38732-61-00-75 219065-14-06-01 219065-14-06-01 219065-14-06-01 5918-34-10 5918-78-10 5918-78-10
13A Stud, Locking Screw Housing/Shear - - - 38732-61-00-75 38732-61-00-75 38732-61-00-75 - - 5918-34-10
14 Nut, Locking Screw Housing 16 32 2709000-14-01 2709000-14-01 2709000-14-01 2709000-14-01 2709000-14-01 2709000-14-01 2709000-14-01
15 Check Valve, Plastic Packing 2 4 M517988 M517988 M517988 M517988 M517988 M517988 M517988
16 Screw, Plastic Packing 2 4 5940-09 5940-09 5940-09 5940-09 5940-09 5940-09 5940-09
17 Pipe Plug, Plastic Packing 2 4 005930-05-10 005930-05-10 005930-05-10 005930-05-10 005930-05-10 005930-05-10 005930-05-10
18 Ring, Plastic Packing 2 4 12469-38 12469-24 12469-24 12469-24 12469-24 12469-52 12469-52
19 Ring, Plastic Energizing 2 4 18586-13 18586-01 18586-01 18586-01 18586-01 18586-14 18586-14
20 Seal Ring, Connecting Rod 2 4 011741-38-00-01 212741-36-00-01 212741-36-00-01 212741-36-00-01 212741-36-00-01 212741-44 212741-44
21 Ring Back-Up 4+ 8+ 21792-22 - - 21792-26 21792-26 - -
22 Seal, Bonnet 2 4 49272-03 644197-03-00-01 644197-03-00-01 644197-03-00-01 644196-01 046613-03 644197-04
23 Pin, Ram Guide 4 8 30313-01 30313-01 30313-01 30313-01 30313-08 30313-06 30313-06
24 O-Ring, Operating Cylinder 4 8 702640-45-51 702640-45-51 702640-45-51 702640-45-51 702645-46-11 702645-46-11 702640-46-11
25 O-Ring, Operating Piston Rod to Int Flg 2 4 18492-91 18492-90 18492-90 18492-90 18492-90 2708811-01 2708811-01
26 Lip Seal, Operating Piston 2 4 710538 710538 710538 710538 710542 710542 710542
27 Seal Ring, Tail Rod 2 4 212741-34-00-01 212741-34-00-01 212741-34-00-01 212741-34-00-01 212741-45 212741-45 212741-45
28 O-Ring, Wiping 2 4 702640-33-71 702640-33-71 702640-33-71 702640-33-71 702640-34-21 702640-34-21 702645-34-21
29 O-Ring, Ram Change Piston to Body 4 8 702640-32-81 702640-32-81 702640-32-81 702640-32-81 702640-33-21 702640-33-21 702640-33-21
30 O-Ring, Ram Change Piston Rod to Int Flg 4 8 702640-33-31 702640-33-31 702640-33-31 702640-33-31 31423-21-13-85 31423-21-13-85 31423-21-13-85
31 O-Ring, Ram Change Cylinder to Int Flg 4 8 702640-34-61 702640-34-61 702640-34-61 702640-34-61 702640-35-41 702640-35-41 702640-35-41
32 O-Ring, Ram Change Cylinder to Bonnet 4 8 702640-42-51 702640-42-51 702640-42-51 702640-42-51 702640-43-41 702640-43-41 702640-43-41
33 O-Ring, Ram Change Piston 4 8 702640-33-81 702640-33-81 702640-33-81 702640-33-81 702640-34-41 702640-34-41 702640-34-41
34 O-Ring, Bonnet Bolt Retainer 8 16 702640-23-91 702640-23-11 702640-23-21 702640-23-91 702640-24-51 702640-23-21 702640-23-71
35 Cap Screw, Int Flange to Bonnet 16*** 32*** 702585-25-00-54 702585-25-00-44 702585-25-00-44 702585-25-00-54 702585-31-00-54 702585-31-00-44 702585-31-00-54
36 Gland, Bleeder 2 4 17454-08 17454-08 17454-08 17454-08 17454-08 17454-08 17454-08
37 Plug, Bleeder 2 4 17454-09 17454-09 17454-09 17454-09 17454-09 17454-09 17454-09
38 Lifting Eye 2 2 11849 11849 11849 11849 11849 11849 11849
39 Packing, Plastic 10 20 7650-08 7650-25 7650-25 7650-25 7650-08 7650-08 7650-25
40 Washer 2 4 689523-05 689523-01 689523-01 689523-01 689523-01 689523-02 689523-02
41 Ring, Retainer 2 4 18572-84 18572-85 18572-85 18572-85 18572-85 33186-85 33186-85
42 Wear Ring, Operating Piston 2 4 49223-01 49223-01 49223-01 49223-01 49223-04 49223-04 49223-04
43 Spacer, Shear**** - - 687117-03 687117-03 687117-03 687117-03 687117-05 - 687117-05
****A large bore shear bonnet is available for these sizes. For part numbers, see page 19. + 11” 15,000 psi requires 8 for single, 16 for double.
****Part numbers shown are for old style shear bonnets. For current model large bore shear bonnet part numbers, see page 19.
****13-5/8” through 16-3/4” and 20-3/4” through 26-3/4” require 24 for single and 48 for double. The 18-3/4” requires 32 for single and 64 double.
****Required on all 11” 15,000 psi and 16-3/4” 10,000 psi BOPs with manual locking screws.
TC1403 13
35
17
16
15
2
24
6
11
29
42
10
38
36
37
34
12
28
27
30
31
32
24
26
5
9
33
3
13
8
7
14
22
41
40
21
19
18
20
23
25
Double U BOP
SD-017500
TC1403 14
16-3/4” 10,000 - 26-3/4” 3000 psi WP U BOP Part Numbers
16-3/4” 18-3/4” 20-3/4” 21-1/4” 21-1/4” 21-1/4” 26-3/4”
Item Qty Qty 10,000 10,000 3000 2000 5000 10,000 3000
Description
No. Sgl Dbl psi psi psi psi psi psi psi
Model II Model II Model II Model II Model II Model II Model II
1 Body 1 1 - - - - - - -
2 Intermediate Flange 2 4 691848 41458 30911-01 30911-01 - 615369-01 -
2A Intermediate Flange/Shear - - * - 41496-01** 41496-01** 49955-01 615418-01 38327
3 Bonnet 2 4 691849 41459 30835-01 30835-02 49963-01 41357 38326
4 Ram Assembly 2 4 644231-( ) 644234-( ) 44256-( ) 44256-( ) 644240-( ) 644240-( ) 44260-( )
5 Piston, Operating 2 4 692828 41460 690058-03 690058 49954-01 41356 614376-01
5A Piston, Operating/Shear - - * - 693405** 693405** - 41374** -
6 Cylinder, Operating 2 4 41365-06 30274-13 30274-04 30274-04 30274-11 30274-11 30274-05
6A Cylinder, Operating/Shear - - - - 41365-04** 41365-04** - 41365-11** -
7 Housing, Locking Screw 2 4 30308-06 30308-09 30308-04 30308-04 30308-08 30308-08 30308-05
8 Locking Screw 2 4 695234 41085 30846 30846 41085 41085 34233
8A Locking Screw/Shear - - - - 34233 34233 - - -
9 Piston, Ram Change/Open 2 4 692756 40961 30848 30848 41064 41064 38174
10 Piston, Ram Change/Close 2 4 692759 40960 30849 30849 41065 41065 38324
11 Cylinder, Ram Change 4 8 30273-13 30273-09 30273-04 30273-04 30273-11 30273-11 30273-05
12 Bolt, Bonnet 8 16 30312-24 30312-23 30312-10 30312-11 30312-26 30312-21 30312-13
12A Bolt, Bonnet/Shear - - - - 41366-10 41366-11 - 41366-21 -
13 Stud, Locking Screw Housing 16 32 5918-34-10 5919-38-10 219065-14-06-01 5918-76-10 5919-38-10 5919-38-10 5918-76-10
13A Stud, Locking Screw Housing/Shear - - - - 38732-61-00-75 38732-61-00-75 - - -
14 Nut, Locking Screw Housing 16 32 2709000-11-01 270900-18-01 2709000-14-01 270900-14-01 2709000-18-01 2709000-18-01 2709111-14-01
15 Check Valve, Plastic Packing 2 4 M517988 M517988 M517988 M517988 M517988 M517988 M517988
16 Screw, Plastic Packing 2 4 5940-09 5940-09 5940-09 5940-09 5940-09 5940-09 5940-09
17 Pipe Plug, Plastic Packing 2 4 005930-05-10 005930-05-10 005930-05-10 005930-05-10 005930-05-10 005930-05-10 005930-05-10
18 Ring, Plastic Packing 2 4 12469-52 12469-72 12469-24 12469-24 12469-70 12469-70 12469-24
19 Ring, Plastic Energizing 2 4 18586-14 18586-19 18586-01 18586-01 18586-18 18586-18 18586-01
20 Seal Ring, Connecting Rod 2 4 212741-44 212741-60 212741-36-00-01 212741-36-00-01 11741-58 11741-58 212741-36-00-01
21 Ring Back-Up 4 8 21792-34 21793-40† - - 21793-39 21793-39 -
22 Seal, Bonnet 2 4 046613-04 644197-05-00-01 046613-16 046613-16 46613-09 46613-09 46613-08
23 Pin, Ram Guide 4 8 30313-06 30313-07 30313-04 30313-04 30313-07 30313-07 30313-05
24 O-Ring, Operating Cylinder 4 8 702645-46-11 2708812-01 702640-45-51 702640-45-51 702640-47-01 702640-47-01 702640-45-51
25 O-Ring, Operating Piston Rod to Int Flg 2 4 2708811-01 41602-04-13-85 18492-90 18492-90 30101-88-13-85 30101-88-13-85 18492-90
26 Lip Seal, Operating Piston 2 4 710542 710543 710538 710538 710544 710544 710538
27 Seal Ring, Tail Rod 2 4 212741-45 212741-36-00-01 212741-34-00-01 212741-34-00-01 212741-36-00-01 212741-36-00-01 212741-34-00-01
28 O-Ring, Wiping 2 4 702640-34-21 702640-34-51 702640-33-71 702640-33-71 702640-34-51 702640-34-51 702640-33-71
29 O-Ring, Ram Change Piston to Body 4 8 702640-33-21 702640-34-01 702640-33-61 702640-33-61 702640-34-31 702640-34-31 702640-34-41
30 O-Ring, Ram Change Piston Rod to Int Flg 4 8 31423-21-13-85 2010180-02 702640-34-11 702640-34-11 31423-52-13-85 31423-52-13-85 702640-34-91
31 O-Ring, Ram Change Cylinder to Int Flg 4 8 702640-35-41 702640-43-51 702640-43-71 702640-43-71 702640-44-01 702640-44-01 702640-43-91
32 O-Ring, Ram Change Cylinder to Bonnet 4 8 702640-43-41 702640-43-81 702640-43-91 702640-43-91 702640-44-21 702640-44-21 702640-44-11
33 O-Ring, Ram Change Piston 4 8 702640-34-41 30101-83-13-85 702640-42-51 702640-42-51 702640-43-11 702640-43-11 702645-42-91
34 O-Ring, Bonnet Bolt Retainer 8 16 702640-24-51 702640-24-71 702640-22-91 702640-22-71 702640-24-71 702640-24-81 702640-23-91
35 Cap Screw, Int Flange to Bonnet 16*** 32*** 702585-31-00-72 702585-36-00-76 702585-28-00-50 702585-28-00-50 702585-36-00-93 702585-36-00-93 702585-31-00-70
36 Gland, Bleeder 2 4 17454-08 17454-08 17454-08 17454-08 17454-08 17454-08 17454-08
37 Plug, Bleeder 2 4 17454-09 17454-09 17454-09 17454-09 17454-09 17454-09 17454-09
38 Lifting Eye 2 2 11849 11849 11849 11849 11849 11849 11849
39 Packing, Plastic 10 20 7650-08 7650-08 7650-25 7650-08 7650-08 7650-08 7650-08
40 Washer 2 4 689523-02 689523-03 689523-01 689523-01 2353-46 2353-46 689523-01
41 Ring, Retainer 2 4 33186-35 33186-01-04 18572-85 18572-85 33186-92 33186-92 18572-85
42 Wear Ring, Operating Piston 2 4 49223-04 49223-07 49223-10 49223-10 49223-11 49223-08 49223-10
43 Spacer, Shear**** - - 687117-05 - 687117-03 687117-03 - - -
****A large bore shear bonnet is available for these sizes. For part numbers, see page 19. †Requires 2 for single and 4 for double.
****Part numbers shown are for old style shear bonnets. For current model large bore shear bonnet part numbers, see page 19.
****13-5/8” through 16-3/4” and 20-3/4” through 26-3/4” require 24 for single and 48 for double. The 18-3/4” requires 32 for single and 64 double.
****Required on all 11” 15,000 psi and 16-3/4” 10,000 psi BOPs with manual locking screws.
TC1403 15
U BOP Hydraulic Control System
The U blowout preventer is designed so that hydraulic pressure opens and closes the rams
and provides the means for quick ram change-out.
Ram closing pressure closes the rams. When the bonnet bolts are removed, closing
pressure opens the bonnet. After the bonnet has moved to the fully extended position,
the ram is clear of the body. An eyebolt can be installed in the top of each ram to lift it
out of the preventer.
Ram opening pressure opens the rams. Following ram change-out, this pressure closes
the bonnets. The rams are pulled outward, near the bonnets before the bonnets begin
moving toward the preventer body. This assures that the rams never obstruct the bore or
interfere with the pipe in the hole. Hydraulic pressure draws the bonnets tightly against
the preventer body and the bonnet bolts are reinstalled to hold the bonnets closed.
SD-017501
TC1403 16
U BOP Operating data and Fluid Requirements Large Bore Shear Bonnet Operating Data and Fluid Requirements
Bore Size and Gals to Open Gals to Close Locking Bore Size and Gals to Open Gals to Close Locking
Closing Opening Closing Opening
Working Pipe Rams Pipe Rams Screw Turns Working Pipe Rams Pipe Rams Screw Turns
Ratio Ratio Ratio Ratio
Pressure (1 Set) (1 Set) (Each End) Pressure (1 Set) (1 Set) (Each End)
7-1/16” All WP 1.3 1.3 18 6.9:1 2.2:1 7-1/16” All WP - - - - -
11” Except 15,000 psi 3.4 3.5 27 7.3:1 2.5:1 11” Except 15,000 psi 6.8 6.9 27 12.0:1 4.8:1
11” 15,000 psi 5.7 5.8 32 9.8:1 2.2:1 11” 15,000 psi 8.9 9.0 32 15.2:1 3.7:1
13-5/8” Except 15,000 psi 5.5 5.8 32 7.0:1 2.3:1 13-5/8” Except 15,000 psi 10.5 10.9 32 10.8:1 4.5:1
13-5/8” 15,000 psi Model B 10.4 10.6 45 10.6:1 3.6:1 13-5/8” 15,000 psi Model B 16.0 16.2 45 16.2:1 6.0:1
16-3/4” 3000 psi Model B 9.8 10.6 38 6.8:1 2.3:1 16-3/4” 3000 psi Model B 18.2 19.0 38 10.4:1 4.4:1
16-3/4” 5000 psi Model B 9.8 10.6 38 6.8:1 2.3:1 16-3/4” 5000 psi Model B 18.2 19.0 38 10.4:1 4.4:1
16-3/4” 10,000 psi 11.6 12.5 45 6.8:1 2.3:1 16-3/4” 10,000 psi 18.2 19.1 45 10.4:1 4.4:1
18-3/4” 10,000 psi 21.3 23.1 54 7.4:1 3.7:1 18-3/4” 10,000 psi - - - - -
20-3/4” 3000 psi 8.1 8.7 46 7.0:1 1.3:1 20-3/4” 3000 ps 14.3 14.9 46 10.8:1 1.7:1
21-1/4” 2000 psi 9.0 8.7 46 7.0:1 1.3:1 21-1/4” 2000 psi 14.3 14.9 46 10.8:1 1.7:1
21-1/4” 5000 psi 27.3 30.0 54 7.2:1 4.0:1 21-1/4” 5000 psi - - - - -
21-1/4” 10,000 psi 24.5 26.9 51 7.2:1 4.0:1 21-1/4” 10,000 psi - - - - -
26-3/4” 3000 psi 10.1 10.8 58 7.0:1 1.0:1 26-3/4” 3000 ps - - - - -
U BOP Operating data and Fluid Requirements Large Bore Shear Bonnet Operating Data and Fluid Requirements
Bore Size and Litres to Open Litres to Close Locking Bore Size and Litres to Open Litres to Close Locking
Closing Opening Closing Opening
Working Pipe Rams Pipe Rams Screw Turns Working Pipe Rams Pipe Rams Screw Turns
Ratio Ratio Ratio Ratio
Pressure (1 Set) (1 Set) (Each End) Pressure (1 Set) (1 Set) (Each End)
7-1/16” All WP 4.9 4.9 18 6.9:1 2.2:1 7-1/16” All WP - - - - -
11” Except 15,000 psi 12.9 13.2 27 7.3:1 2.5:1 11” Except 15,000 psi 25.7 26.1 27 12.0:1 4.8:1
11” 15,000 psi 21.6 22.0 32 9.8:1 2.2:1 11” 15,000 psi 33.7 34.1 32 15.2:1 3.7:1
13-5/8” Except 15,000 psi 20.8 22.0 32 7.0:1 2.3:1 13-5/8” Except 15,000 psi 39.7 41.3 32 10.8:1 4.5:1
13-5/8” 15,000 psi Model B 39.4 40.1 45 10.6:1 3.6:1 13-5/8” 15,000 psi Model B 60.6 61.3 45 16.2:1 6.0:1
16-3/4” 3000 psi Model B 37.1 40.1 38 6.8:1 2.3:1 16-3/4” 3000 psi Model B 68.9 71.9 38 10.4:1 4.4:1
16-3/4” 5000 psi Model B 37.1 40.1 38 6.8:1 2.3:1 16-3/4” 5000 psi Model B 68.9 71.9 38 10.4:1 4.4:1
16-3/4” 10,000 psi 43.9 47.3 45 6.8:1 2.3:1 16-3/4” 10,000 psi 68.9 72.3 45 10.4:1 4.4:1
18-3/4” 10,000 psi 80.6 87.4 54 7.4:1 3.7:1 18-3/4” 10,000 psi - - - - -
20-3/4” 3000 psi 30.7 32.9 46 7.0:1 1.3:1 20-3/4” 3000 ps 54.1 56.4 46 10.8:1 1.7:1
21-1/4” 2000 psi 34.1 32.9 46 7.0:1 1.3:1 21-1/4” 2000 psi 54.1 56.4 46 10.8:1 1.7:1
21-1/4” 5000 psi 103.3 113.6 54 7.2:1 4.0:1 21-1/4” 5000 psi - - - - -
21-1/4” 10,000 psi 92.7 101.8 51 7.2:1 4.0:1 21-1/4” 10,000 psi - - - - -
26-3/4” 3000 psi 38.2 40.9 58 7.0:1 1.0:1 26-3/4” 3000 ps - - - - -
TC1403 17
U BOP Specifications and Accessories
The following specifications apply to typical Cameron U type BOPs. Your Cameron repre-
sentative can provide information on non-standard BOP assemblies.
• Side outlets to 4-1/16” (7-1/16” on 26-3/4” BOPs) can be provided beneath each set
of rams on either or both sides of U BOPs. Side outlets can be studded, open-face
flange or clamp hub with the same pressure rating as the vertical run connections.
• Flanges conform to API standard 6A and/or 16A. Hubs conform to API 16A or
applicable standards. Type 6BX flanges are standard for 10,000 and 15,000 psi
working pressures and for 5000 psi for 13-5/8” and larger bore BOPs.
• Hydraulic control connections for operation of rams and bonnets are 1” NPT. There
are two connections for each set of rams. Wedgelock connections are ½” NPT.
U BOP Standard Accessories
*One required. **Two required for single preventer, four for double preventer. ***Commercially available sockets are recommended.
TC1403 18
Large Bore Shear Bonnets
12A**
24A 2A
26A
5A
42A
Large Bore Shear Ram
Bonnet Assembly
3A
SD-017503
11” 11” 11” 11” 13-5/8” 13-5/8” 13-5/8” 13-5/8” 16-3/4” 16-3/4” 20-3/4” 21-1/4”
Item Description
3000 psi 5000 psi 10,000 psi 15,000 psi 3000 psi 5000 psi 10,000 psi 15,000 psi 5000 psi 10,000 psi 3000 psi 2000 psi
No. (2 Required per Cavity)
Model II Model II Model II Model 79 Model 11 Model II Model II Model B Model B Model II Model II Model II
* Bonnet Assembly (Right) 615195-01 615194-01 614596-01 615419-01 615196-01 615191-01 614498-01 615540-01 615530-01 615537-01 615526-01 615525-01
* Bonnet Assembly (Left) 615195-02 615194-02 614596-02 615419-02 615196-02 615191-01 614498-02 615540-02 615530-02 615537-02 615526-02 615525-02
2A Intermediate Flange/Shear 615188-01 615188-01 615188-01 615459-01 615192-01 615192-01 614766-01 615538-01 615528-01 615535-01 615523-01 615523-01
3A Bonnet/Shear 615189-03 615189-02 615189-01 615640-01 615143-02 615143-01 614772-01 615448-01 615527-01 615534-01 615522-01 615522-02
5A Operating Piston/Shear 645249-01 645249-01 645249-01 615457-01 615209-01 615209-01 614760-01 615539-01 615529-01 615536-01 615524-01 615524-01
702640-45- 702640-45- 702640-45- 702640-45- 702640-45- 702640-45- 702640-45- 702645-46- 702645-46- 702645-46- 702640-45- 702640-45-
24A O-Ring, Int Flg to Bonnet Lip
51 51 51 81 81 81 81 51 51 51 81 81
26A Lip Seal, Operating Piston/Shear 710586 710586 710586 710542 710542 710542 710542 710588 710588 710588 710542 710542
42A Wear Ring, Operating Piston/Shear 49223-15 49223-15 49223-15 49223-04 49223-04 49223-04 49223-04 49223-17 49223-17 49223-17 49223-14 49223-14
**Two shear bonnet assemblies, one right and one left, are required per cavity. The shear bonnet assembly consists of all items shown on the illustration.
**See pages 11, 13 and 15 for bonnet bolt part numbers.
TC1403 19
Tandem Boosters for U BOPs
A BOP equipped with tandem boosters can deliver increased shearing force while not in-
creasing the wear and tear on the packers. Tandem boosters approximately double the
force available to shear pipe. Since the tailrod of the tandem booster has the same stroke
as the BOP’s operating piston, the standard shear locking mechanism can be installed on
the outside end of the booster. For information on lock screws and the required spacers,
see pages 11, 13, and 15.
For information concerning applications where a tandem booster is required, consult
your Cameron representative.
17 7
10
9 4
16
13
11
12
2
6
1
8
3
14 Tandem Booster Assembly
15
23 SD-017504
7-1/16” 3000, 5000, 10,000 and 11’ 15,000 psi 20-3/4” 3000 psi and
Item 11’ 3000, 5000, and 10,000 psi
Description 15,000 psi* 13-5/8” 3000, 5000 and 10,000 psi 21-1/4” 2000 psi
No.
Qty Part Number Qty Part Number Qty Part Number Qty Part Number
1 Cylinder 1 644959-01 2 645113-01 2 645113-03 2 645113-04
2 Cylinder Head 1 644960-01 2 645171-01 2 645171-03 2 645171-03
3 Piston 1 644961-01 2 2032370-02 2 645172-03 2 645172-03
4 Tailrod 1 644962-01 2 645173-01 2 645173-03 2 645173-04
5 Adapter Plate 1 644963-01 2 645115-01 2 645115-03 2 645115-03
6 Screw, SDC HD Cap 8 18541-34 16 18542-13 16 18542-14 16 18542-14
7 O-Ring 1 702640-24-91 2 702640-36-11 2 702645-37-11 2 702645-37-11
8 Seal Ring 1 710541 2 712352 2 710538 2 710538
9 Wear Ring, Operating Piston 1 49223-03 2 49223-21 2 49223-01 2 49223-01
10 Filter, Muffler 1 710621 2 710621 2 710417 2 710417
11 Seal, Lip 1 11741-32 2 212741-33-00-01 2 212741-34-00-01 2 212741-34-00-01
12 Seal Ring 1 710620 2 712351 2 710419 2 710419
13 Wear Ring, Cylinder 1 644443-02 2 644443-03 2 645215-01 2 645215-01
14 Seal Ring 1 705955 2 712445 2 710418 2 710418
15 O-Ring 1 702640-33-11 2 702640-33-51 2 702640-33-71 2 702640-33-71
16 Alignment Ring 1 645116-02 2 645116-01 2 645116-03 2 645116-03
17 Pipe Plug 1 - 2 201018 2 005930-05-10 2 005930-05-10
18 Connector, Tubing 1 19624-01 2 - 4 204887-10-06-57 4 204887-10-06-57
19 Cross 1 6347-08 1 675029-52 1 675029-23 2 675029-23
20 Nipple, Pipe Regular 2 - 1 685902-07-00-30 1 685902-07-00-30 1 685902-07-00-30
21 Hose Assembly 2 711010 2 2708021 2 711374 2 711374
22 Connector, Tubing 1 204888-08-05-56 2 204887-10-05-56 - - - -
23 Stud, Double End - - 16 2010189-03 - - - -
26 Connector, Tubing 1 501133-71-22 2 204887-10-06-56 - - - -
27 Adapter, Pipe - - 2 675029-01 - - - -
*The 7-1/16” tandem booster is a part of the standard land and platform shear configuration for 7-1/16” U BOPs.
TC1403 20
U BOP Ram Hang-Off Weights and
Shear Requirements
Hang-Off Weights
Hang-off weights are estimated capacities with Pipe Size Pipe Rams
hardened top corners of the hang-off rams. This 3-1/2” 300,000 lb (136,078 kg)
enables the rams to dig into the tool joint and 4-1/2” 300,000 lb (136,078 kg)
API Designated Size Ram Type Pressure Rating (psi) Pipe OD (In.) Pipe lb/ft Pipe Grade Shearing Configuration
7-1/16” SBR All 3-1/2 13.3 S Shear Bonnets with Tandem Boosters
11” SBR 10,000 and Lower 5 19.5 E Shear Bonnets with Tandem Boosters
11” DS 10,000 and Lower 5 19.5 E Large Bore Shear Bonnets
11” SBR 15,000 and Higher 5 19.5 G Large Bore Shear Bonnets
13-5/8” SBR 10,000 and Lower 5 19.5 G Shear Bonnets with Tandem Boosters
13-5/8” DS 10,000 and Lower 5 19.5 G Large Bore Shear Bonnets
13-5/8” SBR 15,000 and Higher 5 19.5 S Large Bore Shear Bonnets
16-3/4” SBR All 5 19.5 S Large Bore Shear Bonnets
18-3/4” SBR All 5 19.5 S Standard Bonnets
20-3/4” SBR 3000 and Lower 5 19.5 G Shear Bonnets with Tandem Boosters
21-1/4” SBR 3000 and Lower 5 19.5 G Shear Bonnets with Tandem Boosters
21-1/4” SBR 5000 and Higher 5 19.5 S Standard Bonnets
Note: See pages 19 and 20 for a complete list of part numbers for the large bore shear bonnets and tandem boosters.
TC1403 21
U BOP Pipe Rams
Pipe rams are available for use in Cameron U BOPs to fit all commonly used sizes of tub-
ing, drill pipe, drill collar or casing within the ranges in the charts on pages 23, 24, and 25.
Cameron pipe rams include the following features:
• Cameron pipe rams are self-feeding and incorporate a large reservoir of packer
rubber to ensure a long-lasting seal under all conditions.
• Ram packers lock into place and are not dislodged by well flow.
• All Cameron pipe rams are suitable for H2S service per NACE MR-01-75.
• CAMRAM™ top seals are standard for all U BOP pipe rams from 7-1/16” through
18-3/4” sizes. Packer part numbers beginning with 644xxx indicate the CAMRAM
lipped-plate design. All other packers use standard elastomer material and
reinforcement plates.
• CAMRAM 350™ packers and top seals are available for high temperature service and
for service in which concentrations of H2S are expected.
Top Seal
SD-017508
Ram Packer
TC1403 22
U BOP Pipe Ram Part Numbers
Top Seal
SD-017508
Ram Packer
TC1403 23
Top Seal
SD-017508
Ram Packer
TC1403 24
Top Seal
SD-017508
Ram Packer
TC1403 25
U BOP Shearing Blind Rams
Cameron shearing blind rams shear the pipe in the hole, then bend the lower section of
sheared pipe to allow the rams to close and seal. Shearing blind rams can be used as blind
rams during normal drilling operations.
The DS shearing blind ram can cut larger diameter tubulars or multiple tubing strings
regardless of their orientation to the centerline of the ram. A blade seal between the up-
per and lower faces eliminates the need for moving pipe after shearing.
Features of shearing blind rams and DS rams include:
• Large frontal area on the blade face seal reduces pressure on the rubber and
increases service life.
• Cameron SBRs can cut pipe numerous times without damage to the cutting edge.
• CAMRAM™ top seals are standard for all U BOP shearing blind rams through
18-3/4”. Part numbers beginning with 644xxx indicate CAMRAM. All other top seals
are standard elastomer material.
• H2S SBRs are available for critical service applications and include a blade material of
hardened high alloy suitable for H2S service.
• The Cameron shearing blind ram has a single-piece body with an integrated cutting
edge.
TC1403 26
U BOP H2S Shearing Blind Ram Part Numbers
6
8
7
15 5
12
10
13
4 1
11 14
SD-017509
1
BOP Bore Size and 2 3 4 5 6 7
Upper Ram
Working Pressure (psi) Ram Blade Packer Packer Packer Top Seal Blade Insert
Subassembly
13-5/8” 5000 and 10,000 644781-01 644780-01 644435-01-00-01 46751-01-00-01 46752-01-00-01 644223-01-00-01 644581-01-00-01
18-3/4” 10,000 2010186-01 2010187-01 2010192-01 2010191-01 2010190-01 2010193-01 2010182-01
9
BOP Bore Size and 8 10 11 12 13 14
Lower Ram
Working Pressure (psi) Set Screw Ram Packer Packer Top Seal Blade Insert
Subassembly
13-5/8” 5000 and 10,000 644582-01 644781-02 644780-02 46751-01-00-01 46752-01-00-01 644233-01-00-01 644581-02-00-01
18-3/4” 10,000 644524-01 2010186-02 2010188-01 2010191-01 2010190-01 2010193-01 2010183-01
TC1403 27
U BOP DS Shearing Blind Ram**
6
4 3
4
DS Shearing Blind Ram
SD-017512
TC1403 28
U BOP Shearing Blind Ram Part Numbers
6
1
4 2
3
5
SD-017513
7-1/16”
5000, 10,000 46792-01-00-03 46210-01-00-04 - 49358-01 49358-02-00-01 644214-01-00-01 46792-02 46212-01-00-04 49347-01-00-01 -
and 15,000
11” 5000 and
49392-01-00-02 49009-01-00-02 2010462-04 46751-04 46752-04 644217-01-00-01 049392-02-00-02 049010-01-00-02 46751-04 46752-04
10,000
11” 15,000 614297-01 614275-01 2010462-04 2010460-07 2010461-07 2010453-01 614297-02 614274-01 2010460-07 2010460-07
13-5/8” 5000
46748-01 46749-01 644435-01-00-01 046751-01-00-01 046752-01-00-01 644223-01-00-01 46748-02 46750-01 046751-01-00-01 046752-01-00-01
and 10,000
13-5/8”
614004-01 614002-01 644435-01-00-01 46751-05 46752-05 644226-01 614004-02 614003-01 46751-05 46752-05
15,000
16-3/4” 5000 46766-01 49006-01 46910-03 46751-03-00-01 46752-03-00-01 644229-01-00-01 46766-02 49007-01 46751-03-00-01 46751-03-00-01
16-3/4”
46773-01 46774-01 46910-03 46751-03-00-01 46752-03-00-01 644229-01-00-01 46773-02 46775-01 046751-03-00-01 46751-03-00-01
10,000
18-3/4”
46776-01 46777-01 46910-02 46751-02 46752-02 644232-02 46776-02 46778-01 46751-02 46752-02
10,000
20-3/4” 3000 46783-01 46784-01 - 615235-01-00-01 - 19514-00-00-01 46783-02 46785-01 615247-01-00-01 615247-02-00-01
21-1/4” 2000 46783-01 46784-01 - 615235-01-00-01 - 19514-00-00-01 46783-02 46785-01 615247-01-00-01 615247-02-00-01
21-1/4” 5000 49983-01 49981-01 46910-05 46751-06 46752-06 645478-01 49983-02 49982-01 46751-06 46752-06
21-1/4” 7500
46788-01 49012-01 46910-05 46751-06 46752-06 645478-01 46788-02 49011-01 46751-06 46752-06
and 10,000
TC1403 29
U BOP DSI and DVS Shear Rams
Dual string interlocking (DSI) shear rams and double V shear (DVS) rams are also available
for the U BOP. The interlocking feature of these rams provides the capability of shearing
wireline and braided cable with zero tension in the line, while still maintaining a seal. The
blades are interlocked by using pockets in the lower ram and arms on the upper ram to
prevent any gap between blade surfaces.
DSI rams are similar to standard DS shear rams except for the interlock feature. DSI
shear rams are capable of shearing tubing, small pipe, braided cable, slickline and solid
sinker bar.
DVS rams are similar in design to the standard shearing blind rams except that both
blades are V shaped and interlocked. The DVS rams are capable of shearing tubing, small
pipe, braided cable and slickline.
TC1403 30
Top Seal
Top Seal
Side Packer
Upper Shear Ram
Blade Seal
Upper Shear Ram
TC1403 31
U BOP Variable Bore Rams
One set of Cameron variable bore rams seals on several sizes of pipe or hexagonal kelly.
Variable bore rams are available in the size ranges listed in the chart below. All rams listed
are suitable for H2S service per NACE MR-01-75.
CAMRAM top seals are standard for all U BOP variable bore rams. CAMRAM packers
are available in most sizes. Packer part numbers beginning with 644xxx indicate
CAMRAM. All other packers are standard elastomer material.
The variable bore ram packer contains steel reinforcing inserts similar to those in the
Cameron annular BOP packer. The inserts rotate inward when the rams are closed so the
steel provides support for the rubber which seals against the pipe.
SD-5129
BOP Size and Working Pressure (psi) Pipe Size Range Ram Subassembly Ram Body Packer Top Seal
7-1/16” 3000, 5000, 10,000 and 15,000 3-1/2” to2-3/8” 615066-01 615065-01 614616-02 644214-02-00-01
7-1/16” 3000, 5000, 10,000 and 15,000 4” to 2-7/8” 644901-01 614605-01 614616-02 644214-02-00-01
11” 3000, 5000 5” to 2-7/8” 645360-01 644836-01 644926-01-00-01 644217-01-00-01
11” 3000, 5000, and 10,000 5” to 3-1/2” 645360-01 644836-01 644926-01-00-01 644217-01-00-01
11” 15,000 5” to 2-7/8” 614456-01 644754-01 644931-01 2010453-02
13-5/8” 3000, 5000, and 10,000 7” to 4-1/2” 46675-01 46671-01 644921-01-00-02 644223-02-00-01
13-5/8” 3000, 5000, and 10,000 5” to 2-7/8” 645166-01 644744-01 645089-01 644223-02-00-01
13-5/8” 15,000 7” to 5” 614104-01 614146-01 644924-02 644226-02
13-5/8” 15,000 5” to 3-1/2” 614129-01 644745-01 644921-01 644226-02
16-3/4” 5000 and 10,000 7” to 3-1/2” 46676-01 46672-01 644920-01-00-01 644229-01-00-01
16-3/4” 10,000 (only) 5” to 2-7/8” 49410-01 644746-01 645128-01-00-01 644229-01-00-01
18-3/4” 10,000 7-5/8” to 3-1/2” 46677-01 46673-01 644927-01 644232-03-00-01
TC1403 32
Flexpackers for U BOPs
The Cameron FLEXPACKER ram is designed to close and seal around several diameters of
tubing and pipe. These packers can be used in existing Cameron BOPs. Features include:
• Stacks of metal inserts bonded into the elastomer move radially in the elastomer as
the BOP rams are closed.
• As rams are energized, the proper set of metal inserts is forced against the pipe. The
top plate of the packer fits the largest diameter of pipe.
SD-10315
BOP Size and Description Pipe Size Diameters Packer Part Number Top Seal Part Number
11” 3000, 5000 and 10,000 psi 2-3/8” to 3-1/2” 2010123-01 644217-01-00-01
11” 3000, 5000 and 10,000 psi 2-3/8” to 3-1/2” 2011740-01
11” 3000, 5000 and10,000 psi 3-1/2” to 5” 2163445-01
13-5/8” 3000, 5000 and 10,000 psi 2-3/8” to 3-1/2” 2010113-01 644223-01-00-01
13-5/8” 3000, 5000 and 10,000 psi 2-3/8” to 3-1/2” 2011716-01
13-5/8” 3000, 5000 and 10,000 psi 3-1/2” to 5” 2011673-01
13-5/8” 3000, 5000 and 10,000 psi 5” to 6-5/8” 2011688-01
18-3/4” 10,000 psi 2-7/8” to 5” 645346-01 644232-04
18-3/4” 10,000 psi 3-1/2” - 5” 2011701-01
18-3/4” 10,000 psi 5” to 6-5/8” 2011907-01
20-3/4” 3000 psi 5” to 7” 645353-01 19514-00-00-01
21-1/4” 2000 psi 5” to 7” 645353-01 19514-00-00-01
TC1403 33
CAMRAM 350 Packers and Top Seals for U BOPs
CAMRAM 350 U BOP pipe ram packers and top seals are available for applications which
require high temperature capabilities and greater H2S resistance than standard CAMRAM
packers and top seals.
CAMRAM 350 is available in all U BOP sizes in which standard CAMRAM packers and
top seals are offered. At present, only pipe sizes (up to 5-1/2”) are manufactured.
Camram 350
Top Seal
Camram 350
Packer
SD-017514
TC1403 34
U BOP Rams for Multiple Completions
Non-sealing centralizing rams and companion subsea dual rams and packers for use with
two strings of the same diameter are available for the U BOP. Also available are offset
bore rams for 7-1/16” and 11” BOPs. Contact a Cameron representative for more informa-
tion.
U Blowout Preventer Offset Bore Ram Part Numbers
Actual Centerline
Preventer Size Tubing Size Offset Range Right-Hand Ram Left-Hand Ram Right-Hand Packer Left-Hand Packer Top Seal
Offset Ram Assembly
(in.) (in.) (in.) (1 Reqd) (1 Reqd) (1 Reqd) (1 Reqd) (2 Reqd)
(in.)
7-1/16 1.315 1-3/4 1-3/8 to 1-7/8 44229-01 44108-05 44109-05 21153-07 21154-07 644214-01-00-01
7-1/16 1.660 1-3/4 1-3/8 to 1-7/8 44229-02 44108-03 44109-03 21153-04 21154-04 644214-01-00-01
7-1/16 1.900 1-3/4 1-3/8 to 1-7/8 44229-03 44108-01 44109-01 21153-01 21154-01 644214-01-00-01
7-1/16 2-1/16 1-3/4 1-3/8 to 1-7/8 44229-04 44108-01 44109-01 21153-02 21154-02 644214-01-00-01
7-1/16 2-3/8 1-3/4 1-3/8 to 1-7/8 44229-05 44108-02 44109-02 21153-03 21154-03 644214-01-00-01
7-1/16 2-7/8 1-3/4 1-3/8 to 1-7/8 44229-06 44108-04 44109-04 21153-05 21154-05 644214-01-00-01
11 1.660 2 1-25/32 to 2-7/16 44238-01 44128-04 44129-04 21157-05 21158-05 644217-01-00-01
11 1.900 2-33/64 1-25/32 to 2-7/16 44238-02 44128-08 44129-08 21157-11 21158-11 644217-01-00-01
11 2-1/16 2 1-25/32 to 2-7/16 44238-04 44128-01 44129-01 21157-02 21158-02 644217-01-00-01
11 2-3/8 2-1/8 1-25/32 to 2-7/16 44238-05 44128-02 44129-02 21157-03 21158-03 644217-01-00-01
11 2-7/8 2 1-25/32 to 2-7/16 44238-07 44128-03 44129-03 21157-04 21158-04 644217-01-00-01
11 3-1/2 2 1-25/32 to 2-7/16 44238-08 44128-05 44129-05 21157-06 21158-06 644217-01-00-01
TC1403 35
Bonnet Rebuild Softgoods Kits
For popular size U BOPs, a bonnet rebuild softgoods kit is available to provide all parts re-
quired to reseal the operating system.
Kit parts are shrink-film packed to prevent loss and assure long shelf life. The kits are
less expensive than individual parts. All parts in each kit are identified with part numbers
and parts list index numbers.
24
42
28
34
30
31
32
24
26
27
33
18 21
20
19
25
SD-017515
TC1403 36
Kit Part Numbers
BOP Size (in.) Pressure Rating/Bonnet Type Kit Part Number*
21 Ring, Backup
28 O-Ring, Wiping
39 Packing, Plastic**
TC1403 37
Bonnet Seals and Connecting Rod Seals
For applications where only bonnet and/or connecting rod seals are required, Cameron of-
fers individually packaged components. Connecting rod seals are nitrile rubber. Bonnet
seals beginning with 644197 are the newest design.
When high temperature and/or high concentrations of H2S are expected, Cameron rec-
ommends the used of CAMLAST bonnet and connecting rod seals along with CAMRAM
350 packers and top seals.
U BOP Bonnet and Connecting Rod Seals
TC1403 38
Bonnet Seal Carriers for U BOPs
The bonnet seal carrier is a bore-type
sealing assembly which replaces the face
seal used as the previous bonnet seal.
Sealing capability is not dependent upon
bonnet bolt torque. One seal is captured
in a machined bore in the BOP body
while the other seal is captured in a ma-
chined bore in the intermediate flange.
The seal carrier was designed, devel-
oped and performance-verified for use in
newly manufactured BOPs or as a re-
placement seal assembly for BOPs where
either the BOP body or the intermediate
flange requires weld repair on the seal-
ing surfaces.
The bonnet seal carrier can be retrofitted to any U BOP.
TC1403 39
U BOP Operation and Maintenance (T-172, 2-99)
I. Physical Data
A. Lubricants
1. Ram lubricant, P/N 705725 (CHEMLOA #681 BOP oil) or a water resistant non
petroleum base grease.
2. Thread lubricant - which meets the requirements of the latest revision of API
Bulletin 5A or Moly #503, (P/N 705444, 4 lb can)
b. Standard operation - Use a fresh water lubricant that forms a true solu-
tion rather than an emulsion when mixed with water and/or antifreeze.
6. Seals and sealing surfaces - Hydraulic Oil (10-15 wt) P/N 203497.
B. Dimensional Drawings
1. SD-017499, Single U BOP.
TC1403 40
10. SD-5129, Variable Bore Ram.
D. Weights
Refer to pages 7 and 9.
2. Lift ram assemblies by installing a lifting eye, P/N 011849, in the threaded
preparation in the ram.
3. Normal pressure for the hydraulic operating system is 1500 psi (103 Bars).
5. The maximum hydraulic operating pressure limit is 3000 psi (207 Bars) to op-
erate rams.
TC1403 41
H. API 16A Drift Diameter
Size and Working Presure API Drift Size and Working API Drift
Pressure
7-1/16” 3000 psi 7.032” (179 mm) 16-3/4” 3000 & 5000 psi 16.720” (425 mm)
7-1/16” 5000 psi 7.032” (179 mm) 16-3/4” 10,000 psi 16.720” (425 mm)
7-1/16” 10,000 & 15,000 psi 7.032” (179 mm) 18-3/4” 10,000 psi 18.720” (475 mm)
11” 3000, 5000 & 10,000 psi 10.970” (279 mm) 20-3/4” 3000 psi 20.720 (526 mm)
11” 15,000 psi 10.970” (279 mm) 21-1/4” 2000 psi 21.220” (539 mm)
13-5/8” 3000 & 5000 psi 13.595” (345 mm) 21-1/4” 5000 psi 21.220” (539 mm)
13-5/8” 10,000 psi 13.595” (345 mm) 21-1/4” 10,000 psi 21.220” (539 mm)
13-5/8” 15,000 psi 13.595” (345 mm) 26-3/4” 10,000 psi 26.720” (679 mm)
b. Supports 300,000 lb (136, 078 kg) of pipe size at the lower end of the
range, 600,000 lb (272,155 kg) at the higher end of the range.
3. Shear rams
a. Shearing capabilities are dependent upon the size and working pressure
of the BOP and the shearing configuration associated with that BOP.
4. Bonnet
TC1403 42
III. Disassembly Procedure
A. Part Preparation Prior To Disassembly
The work area should be clean and well lighted.
B. BOP Disassembly
Reference page 10.
1. Use an air wrench to break and unscrew the bonnet bolts (12) on both sides
of the BOP.
2. Apply hydraulic closing pressure to the rams CLOSE connection on the BOP to
open the bonnet assembly.
3. Screw the lifting eye (38) into the top of the ram.
4. Use a hoist to lift up on the ram to remove it from the operating piston rod.
5. Remove the seal (22) that resides in the seal bore of the BOP body.
6. With a spanner wrench and a hammer, break loose the locking screw hous-
ing nuts. (14).
7. Remove the nuts, the locking screw housing (7), and the locking screw (8).
8. Remove the locking screw housing studs (13) with a small pipe wrench.
11. Remove the O-ring (34) from each bonnet bolt and remove the bolts from
the bonnet asembly.
12. Insert the lifting eye (38) into the intermediate flange or into the bonnet.
13. Attach a hoisting cable to the lifting eye and apply tension to the cable to
hold up the bonnet asembly.
14. Using a crescent wrench, loosen the ram change pistons (9) and (10) on the
flats provided.
TC1403 43
15. Once the ram change pistons are completely loose, move the assembly to the
side away from the main body of the BOP.
C. Bonnet Disassembly
1. Remove the ram guide pins (23) from the intermediate flange (2).
2. Remove the cap screws (35) to disassemble the intermediate flange from the
bonnet.
4. Remove the ram change cylinder O-rings (31) and (32) from the cylinders, and
remove the cylinders from the bonnet.
5. Remove the operating cylinder O-rings (24) from the operating cylinder, and
remove the cylinder from the bonnet. These O-rings are for standard bonnets
only. The large bore shear bonnets do not have a separate operating cylin-
der.
6. Remove the operating piston seal ring (26) and the operating piston wear
ring (42) from the operating piston, and remove the piston from the bonnet.
7. Pull out the remaining seals in the bonnet bore, including the wiping O-ring
(28) and the lip seal for the tail rod (27).
TC1403 44
IV. Assembly Procedure
A. Part Preparation Prior to Assembly
The work area should be clean and well lighted.
1. Remove all dirt, grit, oil, and contaminates from the ram bore, ram change
piston holes, bonnet stud holes, all fluid passageways in the body, and inter-
mediate flange. Clean water and detergent should be used for cleaning.
High pressure air may also be used if it is dry air.
2. Clean all internal surfaces of bonnets using clean water and detergent. Lubri-
cate internal sealing surfaces.
3. Clean pistons, cylinders, and intermediate flanges, using clean water and de-
tergent. Lubricate areas that will come in contact with other parts.
4. Lubricate sealing surfaces behind the threads in the bonnet stud holes in the
BOP body after cleaning this area.
5. Sealed elastomer containers should not be opened until they are required for
assembly. This is to prevent contamination and damage to the seal.
B. Bonnet Assembly
Reference page 10.
1. Place each bonnet (3) on stands or pallets with the bore side up.
2. Install the tail rod lip seal (27) and the wiping O-ring (28) into the bonnet (3).
3. Place the operating cylinder O-rings (24) on the operating cylinder (6). These
O-rings are for standard bonnets only. The large bore shear bonnets do not
have a separate operating cylinder.
4. Insert the operating cylinder (6) into the standard bonnet bore.
6. Place ram change piston O-rings (33) and the ram change piston to body
O-rings (29) on the both ram change pistons.
7. Insert the assembled ram change pistons (9) and (10) into the bonnet so that
the pistons with side holes are on the OPEN side, and the pistons with center
holes are on the CLOSE side.
Caution: Ensure that the threaded end of the ram change piston does not contact the
floor.
TC1403 45
8. Place the operating piston wear ring (42) and the seal ring (26) onto the op-
erating piston (5).
10. Place the intermediate flange (2) on the assembly table with the threaded
holes for the guide pins (23) in the bottom position.
11. Place the operating piston rod O-ring (25) in the central bore.
12. Install the plastic packing ring (18) and energizing ring (19).
13. Install the connecting rod lip seal (20), lip seal retainer (40), the back-up ring
(21), and spirolox retaining ring (41).
15. Install the cylinder O-rings (31) and (32) onto the ram change cylinder.
16. Apply a light coat of oil on the O-rings and inside the corresponding seal
bores in the bonnet (3) and the intermediate flange (2).
17. Install the assembled intermediate flange onto the assembled bonnet.
18. Install the cap screws (35) from the bottom side of the intermediate flange
and tighten them securely. Be sure that the plastic packing port on the inter-
mediate flange is on the same side of the assembly as the lifting eye hole on
the bonnet.
Caution: a. Ensure the the tail rod seals are not damaged.
b. Ensure that the seals are not damaged during the bonnet seating process.
Important: The threaded holes for the lifting eyes in both the bonnet and the intermedi-
ate flange must be on the same side of the connecting rod.
19. Tighten the cap screws in a crisscross pattern so that the intermediate flange
pulls down straight and level with respect to the face of the bonnet. Torque
the cap screws between 3350 and 3670 ft-lb (4542 and 4976 N•m).
20. Screw the ram guide pins (23) into the intermediate flange. Tighten the
guide pins with a pipe wrench to a maximum of 500 ft-lb (678 N•m).
21. Install the lifting eye (38) into the intermediate flange or into the bonnet.
22. Position the bonnet assembly next to the body and thread the ram change
pistons onto the body.
23. Tighten the rods securely against the body, using a crescent wrench on the
flats provided.
TC1403 46
Warning: Make sure that the open and close pistons are in the appropriate location with
respect to the body.
24. Insert the bonnet bolts (12) through the bonnet and intermediate flange.
25. Push the bonnet bolt O-rings (34) over the bonnet bolt threads onto the un-
dercut.
26. Screw the plastic packing check valve (15) all the way into the preparation in
the intermediate flange.
27. Insert one stick of plastic packing (39) above the check valve and install the
plastic packing screw (16). Do not apply any torque to the plastic packing
screw.
29. Install the bleeder gland (36) with the plug (37) into the bonnet.
30. Install the double ended locking screw studs (13) into the bonnet. The short
threaded ends screw into the bonnet. These studs can be tightened with a
small pipe wrench used close to the bonnet.
31. Install the locking screw (8) into the locking screw housing (7).
32. Install the locking screw housing over the studs with the flats on the housing
flange vertical. Install and tighten the locking screw housing nuts (14).
Note: All hydraulic lines must be in place. Install the seal carrier before the rams are in-
stalled.
33. Lubricate the seal bores for the bonnet seal in both the BOP body (1) and the
intermediate flange (2).
34. Install the bonnet seal (22) that will reside in the seal bore of the intermedi-
ate flange.
36. Close the bonnet asembly with 200 to 500 psi (13.8 to 34.5 Bars) operating
presure, trapping the seal carrier.
38. Once the bonnet seals are securely installed, connect the hydraulic lines to
the OPEN and CLOSE ports on the sides of the preventer body.
TC1403 47
39. With the bleed gland (36) loose, on the top of the bonnets, apply 200-300 psi
(13.8 - 20.7 Bars) OPEN and CLOSE operating pressure alternately to expel air
from the operating system.
40. After the air is bled from the system, tighten the bleed plugs (37).
41. Install the appropriate ram assemblies (4) onto the operating piston rod.
42. After assembling both bonnets, apply 1500 psi (103 Bars) hydraulic pressure
to the rams OPEN connection to close the bonnets.
43. Apply thread lubricant to the threads and below the head of the bolt.
44. Screw in and torque the bonnet bolts to according to the charts on page 54
and 55.
1. The capacity and the pressure rating of the accumulators and the pressure
pumps must comply with the API RP53 recommendations or appropriate reg-
ulatory agency requirements.
2. Ensure that the ring gaskets are correct for the preventer flange, the hub
size, and the pressure rating.
B. Installation
1. Install the preventer, ensuring that the preventer is right-side-up (outlets are
below the center of the preventer).
2. Inspect the preventer, the ram subassemblies, and all rubber parts during in-
stallation.
4. Lift the BOP with slings installed around the body of the BOP.
7. Remove the 1” ball valves or pipe plugs from the inlet and outlet connec-
tions.
TC1403 48
8. Connect the hydraulic control lines, and flush the operating system with
clean fluid.
9. Test for leaks in the operating system (refer to Part VII, TESTING.)
10. Install the rams in accordance with the assembly procedure described in Part
IV, ASSEMBLY.
11. While installing the rams, inspect the ram bore and bonnet.
b. Inspect the intersection between the vertical bore and the ram bore.
Grind out any raised metal surfaces. Do not remove any metal below the
original surface.
Caution: To avoid damage to the packers, close pipe and variable bore rams only when
pipe is in the preventer.
2. Pressure test and operate the preventer once a week per API RP53 “Periodic
Field Testing” or appropriate regulatory agency requirement.
B. Periodic Maintenance
1. Once a year, or every six months in cold weather conditions, completely dis-
assemble the preventer.
TC1403 49
2. Reassemble the preventer.
a. After reassembling the preventer, test the rams and operating system. Re-
fer to Part VII, TESTING for the correct procedure.
VII. Testing
A. Hydraulic Operating System
1. Test the hydraulic operating system after installation.
1) Apply a maximum of 300 psi (20.7 Bars) hydraulic pressure to the OPEN
port.
4) Apply a maximum of 300 psi (20.7 Bars) hydraulic pressure to the CLOSE
port.
Note: If testing pipe, casing, flex packers, or variable bore rams, be sure that an appropri-
ate size test mandrel is installed into the preventer. DO NOT close the rams on an
open hole unless closing pressure is less than 300 psi (20.7 Bars). Flex Packers and
VBRs should be tested with the largest pipe size for that packer.
2) Apply 300 psi (20.7 Bars) hydraulic pressure to the CLOSE port, and ob-
serve the OPEN port for leaks.
3) Increase the pressure to 3000 psi (207 Bars) and observe the OPEN port
for leaks.
4) Inspect for leaks between the intermediate flange, the bonnet, and the
BOP body. Bleed all pressure from the BOP closing line.
TC1403 50
6) Remove the hydraulic line from the CLOSE port.
7) Apply 300 psi (20.7 Bars) hydraulic pressure to the OPEN port, and ob-
serve the CLOSE port for leaks.
8) Increase the pressure to 3000 psi (207 Bars) and observe the CLOSE port
for leaks.
9) Inspect for leaks between the intermediate flange, body, and bonnet.
Bleed all pressure from the BOP opening line.
11) Replace the seals if leaks were observed and repeat the test with new
seals.
B. Ram Test
(After installation and as required by API RP53 or appropriate regulatory
agency.)
1. Hydraulically test ram packers with water using the following procedure:
a. Install the BOP stack on a prepared test stump or install a test plug below
the BOP if on the wellhead.
b. Inspect for ram packer leaks at low pressure by closing rams on an appro-
priate size test mandrel (none if blinds or shears are used) with 1500 psi
(103 Bars) operating pressure, and apply 200 psi (13.8 Bars) pressure under
the rams. Hold pressure for 3 minutes. Maximum pressure drop is 10 psi
(.7 Bars) in 3 minutes.
d. If rams leak at low pressure or at working pressure, inspect for worn ram
packers and replace if necessary.
e. Repeat the above procedure for each set of casing, pipe and shear rams.
TC1403 51
VIII. Storage
A. Preventer
1. Open the bonnets and remove the ram subassemblies.
2. Remove the top seals and packers, then wash the ram subasemblies.
Note: Rubber products that have been put into service and that are subsequently stored,
will have an unpredictable shelf-life. This is attributable to their varied physical con-
dition when returned to storage, due to the inability to completely remove
elastomeric solvents (hydrocarbon contaminates, etc.) and storage in a container
filled with air (chemically active gases).
6. Dry with an air blaster until no moisture is left inside or outside the
preventer.
7. Inspect the ram bores and the vertical bores for burrs.
10. Lubricate the end and outlet connection faces with a heavy grease, and cover
them with flange protectors.
12. Fill the operating system with preservation fluid Cameron P/N 718100.
13. Install the 1” NPT pipe plugs into the OPEN and CLOSE connections.
14. To lift the preventer, use appropriately rated slings around the ends of the
body.
TC1403 52
B. Elastomers
1. Store rubber products inside a cool, dark, and dry storage area.
a. The preferred storage temperature range for rubber goods is from 40°F to
80°F (4.4°C to 26.7°C).
4. Keep the rubber products clean and free of solvents, oil, greases, or any
other semi-solid or liquid materials during storage. Rubber goods should spe-
cifically be protected against direct contact with: manganese, copper, copper
alloys (including brass), polyvinyl chloride (PVC), creosote-impregnated tim-
ber, other rubber goods of different rubber compounds, sulphur, and copper
napthenate.
5. When cleaning is necessary, rubber goods may be cleaned with either soap
and water or methyl alcohol. After cleaning, the rubber goods should be
dried at room temperature.
Important: Rubber goods taken from storage must ALWAYS be inspected before installa-
tion. Rubber goods should not be flexed at temperatures below 40°F (4.4°C).
Rubber goods in storage should be inspected every 12 months to ensure that
they are still serviceable.
a. Ensure that the part does not have a tacky surface or noticeable softening
or hardening of the surface.
b. Flex the part and inspect with a magnifying glass to ensure that there are
no cracks.
c. Replace items which show any of the aging signs mentioned above.
TC1403 53
Bonnet Bolt Torque Requirements for Seal Carrier BOP Bonnets
Bonnet Hex Cameron Torque Min Torque Max
Bore Size Bolt Thread Across Wrench Moly Lub** Moly Lub**
W.P. (psi) P/N 8-UN Flats * ft-lb N•m ft-lb N•m
7-1/16” 3000 30312-06 1-3/4” 2-3/8” 713114-08 393 533 589 799
7-1/16” 5000 30312-02 2” 2-3/8” 713114-08 468 635 701 950
7-1/16” 10,000 30312-07 2-1/2” 2-3/4” 713114-10 695 942 1042 1413
7-1/16” 15,000 30312-01 2-7/8” 2-3/4” 713114-10 801 1086 1201 1628
11” 3000 30312-04 2-1/4” 2-3/4” 713114-10 1279 1734 1918 2600
11” 5000 30312-03 2-1/2” 2-3/4” 713114-10 1386 1879 2079 2819
11” 10,000 30312-05 3-1/8” 2-3/4” 713114-10 1676 2272 2514 3409
11” 15,000 30312-12 3-3/4” 3-1/2” 713114-13 2198 2980 3297 4470
13-5/8” 3000 30312-09 2-3/4” 2-3/4” 713114-10 1088 1475 1632 2213
13-5/8” 5000 30312-01 2-7/8” 2-3/4” 713114-10 1121 1520 1681 2279
13-5/8” 10,000 30312-12 3-3/4” 3-1/2” 713114-13 1534 2080 2300 3118
13-5/8” 15,000 30312-18 4-1/2” 4-5/8” - 4953 6715 7430 10,074
16-3/4” 3000 30312-17 2-7/8” 3-1/2” 713114-13 1842 2497 2763 3746
16-3/4” 5000 30312-16 3-1/2” 3-1/2” 713114-13 2211 2998 3316 4496
16-3/4” 10,000 30312-24 4-1/2” 4-5/8” - 5931 8041 8896 12,061
18-3/4” 10,000 30312-23 4-3/4” 4-5/8” - 4417 5989 6625 8982
20-3/4” 3000 30312-10 2-1/2” 2-3/8” 713114-08 1923 2607 2884 3910
21-1/4” 2000 30312-11 2-1/4” 2-3/4” 713114-10 1690 2291 2534 3436
21-1/4” 5000 30312-26 4-3/4” 4-5/8” - 3726 5052 5588 7576
21-1/4” 7500 30312-21 5” 4-5/8” - 6976 9458 10,464 14,187
21-1/4” 10,000 30312-21 5” 4-5/8” - 6203 8410 9304 12,615
26-3/4” 2000 30312-10 2-1/2” 2-3/8” 713114-08 1907 2586 2860 3878
26-3/4” 3000 30312-13 3-3/4” 3-1/2” 713114-13 3079 4175 4618 6261
**Where no wrench part number is listed, a commercially available socket is recommended.
**Moly Lub means a molybdenum disulfide lubricant similar to NSW #503 and FEL-PRO #670.
TC1403 54
Bonnet Bolt Torque Requirements for U BOPs without Seal Carriers
Bonnet Hex Cameron Torque Torque
Bore Size Bolt Thread Across Wrench API 5A Lub Moly Lub**
W.P. (psi) P/N 8-UN Flats * ft-lb N•m ft-lb N•m
7-1/16” 3000 30312-06 1-3/4” 2-3/8” 713114-08 1600 2169 900 1220
7-1/16” 5000 30312-02 2” 2-3/8” 713114-08 2200 2983 1200 1627
7-1/16” 10,000 30312-07 2-1/2” 2-3/4” 713114-10 4200 5694 2300 3118
7-1/16” 15,000 30312-01 2-7/8” 2-3/4” 713114-10 6000 8135 3300 4474
11” 3000 30312-04 2-1/4” 2-3/4” 713114-10 3000 41067 1600 2169
11” 5000 30312-03 2-1/2” 2-3/4” 713114-10 4200 5694 2300 3118
11” 10,000 30312-05 3-1/8” 2-3/4” 713114-10 7900 10,711 4100 5559
11” 15,000 30312-12 3-3/4” 3-1/2” 713114-13 14,500 19,659 7500 10,169
13-5/8” 3000 30312-09 2-3/4” 2-3/4” 713114-10 5600 7593 3000 4067
13-5/8” 5000 30312-01 2-7/8” 2-3/4” 713114-10 6000 8135 3300 4474
13-5/8” 10,000 30312-12 3-3/4” 3-1/2” 713114-13 14,500 19,659 7500 10,169
13-5/8” 15,000 30312-18 4-1/2” 4-5/8” - 25,500 34,573 13,000 17,626
16-3/4” 3000 30312-17 2-7/8” 3-1/2” 713114-13 6000 8135 3300 4474
16-3/4” 5000 30312-16 3-1/2” 3-1/2” 713114-13 12,500 16,948 6500 8813
16-3/4” 10,000 30312-24 4-1/2” 4-5/8” - 25,500 34,573 13,000 17,626
18-3/4” 10,000 30312-23 4-3/4” 4-5/8” - 29,500 39,997 15,500 21,015
20-3/4” 3000 30312-10 2-1/2” 2-3/8” 713114-08 4200 5694 2300 3118
21-1/4” 2000 30312-11 2-1/4” 2-3/4” 713114-10 3000 4067 1600 2169
21-1/4” 5000 30312-26 4-3/4” 4-5/8” - 29,500 39,997 15,500 21,015
21-1/4” 7500 30312-21 5” 4-5/8” - 34,000 46,098 17,500 23,727
21-1/4” 10,000 30312-21 5” 4-5/8” - 34,000 46,098 17,500 23,727
26-3/4” 2000 30312-10 2-1/2” 2-3/8” 713114-08 4200 5694 2300 3118
26-3/4” 3000 30312-13 3-3/4” 3-1/2” 713114-13 14,500 19,659 7500 10,169
**Where no wrench part number is listed, a commercially available socket is recommended.
**Moly Lub means a molybdenum disulfide lubricant similar to NSW #503 and FEL-PRO #670.
TC1403 55