LYSAGHT TRIMDEK is a trapezoidal ribbed profile with subtle fluting to the pans. Its bold and widely spaced ribs give pleasing visual affects. It is an ideal and economical choice for housing, commercial and industrial applications.
LYSAGHT TRIMDEK is a trapezoidal ribbed profile with subtle fluting to the pans. Its bold and widely spaced ribs give pleasing visual affects. It is an ideal and economical choice for housing, commercial and industrial applications.
LYSAGHT TRIMDEK is a trapezoidal ribbed profile with subtle fluting to the pans. Its bold and widely spaced ribs give pleasing visual affects. It is an ideal and economical choice for housing, commercial and industrial applications.
LYSAGHT TRIMDEK is a trapezoidal ribbed profile with subtle fluting to the pans. Its bold and widely spaced ribs give pleasing visual affects. It is an ideal and economical choice for housing, commercial and industrial applications.
LYSAGHT TRIMDEK
iene ae)
registered testing laboratory has
been used to develop the limit state
performanceafthe dadding.
‘The Direct Pressure Test Rig offers 9
much better modelling of wind load,
compared to treditonal sr bag test
methods.
Simple, Low Cost Fixing
Specification The long, straight lengths of
LYSAGHT TRIMOEK is a trapezoidal LYSAGHT TRIMDEK canbe lowered
ribbed profile with subtle flting to intoplace and easly aligned. Fixing is
the pars. ts bold and widely spaced simple and fast
ribs give pleasing visual affects. ts
superior spanning capabilities, Minimum Roof Pitch
economical effective cover make Long lengthe and 2 special anti
LYSAGHT TRIMDEK is an ideal and capillary side lap allow LYSAGHT
economical choice for houring, TRIMDEK HI-TEN to be used safoly
commercial and industrial — onpitchesaslowas2’
applications. LYSAGHT TRIMDEK is
aise suitable for carports, verandss, Sprung Curved Sheeting
fences and hordings. When used as LYSAGHT TRIMDEK can be sprung
wall cladding, hording facades, curved over an arched roof for deta
fences, the trapezoidal ribs can be contact PT BlueScope Lysaght
run vertically horizontal Indonesis Techical Depertment.
finish canforms to AS 1397.G550-AZ
150 The Clean COLORBOND” pre-
pointed finish is applied over
ZINCALUME steel, coating class AZ
150 (misimum average 150 g/m2
coating mass) and is accordance with
AS 2728, ‘Pre-painted and Organic
Film /Metal Laminate Product
Mixand Match
‘The wide choice of colours and styles
from BlueScope Lysaght Indonesia
tllows you to mix and match with
Advantage Of High Tensile Steel
‘The yield strength of high tensile
G550 ZINCALUME steel ie almost
four times as high as that of 6300
ZINCALUME or soft steel, Due 0 this
significant difference, G550 high
tensile steel roofing and valing
profes offer the folowing benefits
Latest Technology Material
State ofthe attesting methodshave \ySAGHT TRIMDEK finishes. have
been used to determine the pave steel G5S0(S50 Mpa minimum
performance of LYSAGHTTRIMDEK. yield stres) and 0.35, 0.40, 0.45,
The Diroct Pressure Testing Rig at 0,50,0.55mmbasemetalthickness
BlueScope Lysaght’s NATA The standard ZINCALUME” stee!
overG300 products:
he longerspanringcapabites(less
Mass & Yield LYSAGHT TRIMDEK ke
Thickness (mm) | Clean COLORBOND | ZINCALUME steel higher load carying capabilities
(less permanent deflection
ew [rer | Kam | Kgima | Kam | Kg/ma renter durability ess dents)
03s 040 «2800369278 at reduced building costs
oa) 045318 ate 310
045 050 355 a7 3.49 a9 bomen
Lead or copper are not compatible
O50 055 391 615385 5.08 with Clean COLORBOND orrest Fined Mw BuLDEX rw BuLDeX
Setting Serew Selfsting Serew
CTEKS 12-14X45HGS TEKS 12-11 X45 HGS
Volley Fined for MW BUILDEX rw BULDEX
Walls Only Selling Screw Selling Screw
(CTERS 12-1420 HWES
Side Laps and MW BUILDEX
Accestoree Selling Serew
CSP 10-16% 16 HES.
ZINCALUME steel. Copper gutters,
pipes ts, must not discharged onto
ZINCALUME steel or Clean
‘COLORBOND.
Fasteners
BlueScope Lysaght Indonesia
recommend that fasteners be
selected having durability
compatible wth the roof material
Poor quality fasteners will lead to
Lnsighty staining and or early Flare
of the roof material The use of
Electro Plated Zine or Cadmium
Plated screws without additional
protwetion are nat recommended
Fasteners must comply with
Australian Standard AS 3566
Amendment 1990 else 3 erows self
driling for the Building and
Construction industry. Approved
fasteners, color matched or lain are
avaliable from BlueScope Lyssght
Indonesia
Tolerances
Length 20,15 mm
CoverWidth —£4mm
Lengths
Sheets are avaliable custom cut upto
1Smeustom eut Longe lengths can
be supplied, provided satisfactory
transport and onsite handing ean be
arranges
Care and Stora
Installation
Roof sheeting is delivered in
“rapped bundles and should not be
allowed to get wet. Bundles should
be stored clear of the ground and
protected by waterproof covers. If
bundles become wet, the sheets
should be separated, wiped with a
clean cloth and stacked allow sir
Prior to
ulation and completes dying
Handling On site
Long lengths shouldbe ited using »
spreader bar and fabric sing. Clean
ty gloves should be used. The
sheets should not be dragged
‘ver rough surfaces 0” each other
(Care shoul ao be taken to provent
tooledragging onthe surface.
CTEKS 12.11 x25 HGS
om
Cutting Sheets On site
Apowerraw withmetalcuttng blade
le the best method for cutting
LWSAGHT TRIMDEK sheets on site
Metal blades are preferred to
cxrborundum discs a¢ they produce
ewer damaging hot mata particles
tnd leave les bur on the cut sheet
coated material. Sheets should be
placed face down on padded
supports. When uttingroofshoeting
take care to protect the sheeting
from swarf. Whenever possible,
futing. should be done on the
ground and not over ther should net
be cared out on top of other
paintedsurfaces
Laying Procedure
LSAGHT TRIMDEK uses male and
female ribs for lapping. Lift sheetsfatng should be done on the
ground and not over other should
not be eared out on top of other
paintedsufaces
Laying Procedu
LYSAGHT SPANDEX uses male and
fomale ribs, Lift sheets ont the right
way up with ether ll male or female
Fibs facing the same direction,
otherwise sheets will have to be
tumed end-forend ducing fing. For
correct side lapping, the lb with the
longtucina ant-cpilary fst (male
1b) is covered bythe side rib without
the longitudinal fute (female 1)
‘Where LYSAGHT SPANDEK roof
pitches re lessthan 25° orwherethe
roof is exposed to extreme weather
conditions, sheets flanges to be
turned up approximately 80" at the
high end ofthe roo, i, at ridges or
fascia, and tured down or inped
slightly atthe guter.turn.up tools
taille for the turn-up operation
‘which can be carried out before or
after the sheets ae fixed in positon.
HW eumed-up aftor fixing, at least 25
rm clearances required atthe end
of the sheets to position the too
Fixing of walling application similar
toroofing
Fastening Shoots to Supports
LYSAGHT SPANDEK may be crest
fined to timber or steel roofing of
waling supports, or valley fixed to
steel supports or timber waling
supports. Do not locate fasteners
less than 251mm from end ofshaets
Walking On Roof sheeting
When walking along the length of
LYSAGHT SPANDEK walk on atleast
‘wo ibe. When walking acrose the
width of roof sheeting, especialy
‘overhangs, walk over or close tothe
roofing supports. Generally keep
weight evenly distributed over the
sols ofthe feet. Clean andeoft soled
shoes should be worn. Care should
bbe takenwith aw sheets as they may
boslopery
Cleaning Up
‘All metalic swart and other debsis
should be swept from the roof area,
and gutters regularly, atthe end of
‘the day and atthe completion ofthe
instalation. Failure todo so ean ead
te surface staring as the meta
particles oxic
Joint Sealing
As it not practical to solder
ZINCALUME steel, where sealed
joints re requited uso ser or rvs
and sileone sealant. Only sealants
branded as suitable for use with
Eso
ARRAS
Ree me
a ane cian
se,
nannies
rear
Bar ate en ge
TERI
LOGY
Galvanized or ZINCALUME stee!
shouldbe ured.
LYSAGHT Products Rainwater
Goods
Whether you're renovating cassie
houte or searching for a ditinetve
look fora new home ad the perfct
finishing touch to the LYSAGHT
SPANDEK roof with our extensive
range o rainwater goods. BueScope
Lysaght Indonesia rainwater goods
provide the perfct fishing touchEon
LYSAGHT TRIMDEK Wind Capacities (KPA) - Limit State
IER ESE
2
140135 amo Oss 03s,
035 G40 Siglo Serenity 280
Stengh 740515240 255 205 170 15D 050
End Sereasbiy 295/275 275) 230 | 180, 125° 080/175 030
Siengh 660 $95 520 445350 27 210 OF as
Intel Sevens | 240° 2706-2556 230 195° 455° 120 | 200 as
Siwegh 750 700 640 S45 425 330 250 040 100
040 045 Single Serenity | 425° 345° 255° 170 140 100 Os
Seng 1025815 595 450 325 200275 06s
End Sercasiy | 445 325° 2900 2401S 435 LoD | 2700
Antal Seibasiy | 435-370 310) 245 | 2274800 44s | 300" 08S
Seng $85 a5 700 Sas ass 370 325, 2a
045 050 Shale Sarsennity| 415 450°/ 410/150 145 DMD 04s
Swergh 1200 1080 905 705 sas 430 350 075
nd Sevens! | $201 4361/50) 2201200) 445/145" |-8100 [050
Stengh 845 TSS 65D S80. 44 4) 34S 148275
Inuanal Soreasbty| 430 S00 400415255. 205175. as S|
Steegn WAS 90-740 430 S35 470 as ass
250055 Single Serenity | 700, 495° 345 215120078 O50
Seng 12001200 1130-920 720 57 440 ass
end Seventy | 00° 490° 380) 295) 2200 dO 15" | 40" 04
Stengh 1445945 78D 625505430 3] 158 325
Antal Serta | 825.460" S10) 360. 2900229 Nas /az6 | 130
Stengh TIS 1000845738 63D SAD 70 395dire maybe rpeacea ned hae
eed ny emery on ua ee,
Fer further nlenaton,brechires
ted you tral dobar eal
phone : (021) 8998-2965
facs (021) 8998-2966
4.18 Dana sh Bok 00272
anand 2100
INDONESIA
www bluescopesteel.co.id
PT BlueScope Lysaght Indonesia
Jakarta:
(62-21) 8998-2965
(62-31) 897-1279
Medan:
(62-61) 685-1555
BLUESCOPE
LYSAGHT