Professional Documents
Culture Documents
BBL Crane and Hoist Duty Motors
BBL Crane and Hoist Duty Motors
We also supply motors for special types of duties, Motors with Integral Brakes
on enquiry, including multi-speed motors with How to select motors for hoisting
squirrel cage rotors. and similar duties. These motors can be supplied with integral fail
The common Cyclic Duration Factors (CDF) for safe D.C. brakes in frame sizes upto 132M, with
the above duties are 25%, 40% and 60%. We The formula to establish the rated output Pn in kW built in rectifiers (so that no seperate supply is
also supply, on enquiry, motors for other CDF’s. is : required). The braking torque values are :
The CDF calculations are shown in figures 1(a), Frame size : 71 80 90S/L 100L 112M 132S/M
1(b), 1(c),. Unless otherwise specified a duty cycle F xV Braking
Pn > = kW
is ten minutes long. 102 x efff torque Kgm : 0.5 1 2 4 5 or 6 5 or 6
Please refer to table 1 for examples of typical These are of TEFC contruction, smaller than the
starting duties and selection of starting class. surface cooled motors used conventionally.
where F = maximum total load in Kg. For details, please refer our brake motor
Tables given herein are for load GD2 equal to or
catalogue.
less than rotor GD 2 . For cases where load V = Hoisting speed in mtrs/sec., and
GD2>rotor GD2 the motor should be selected from
the table with a higher no. of starts/hr. as per the
eff = overall mechanical Flame-proof crane duty motors
formula efficiency of the driving unit These are also available on enquiry.
No. of starts allowed = No. of starts as per table
x 2 x GD2 of rotor / (GD2 of rotor - GD2 of load).
1
1/9
Bharat Bijlee Limited
Crane & Hoist Duty Motors CC1/B
If motors in the selection tables are to be
operated under ambient temperature other than
400C, a correction factor shall be applied as
given in Fig. 2
CORRECTION FACTOR
crushers, main and auxiliary drives in rolling mills by rated current x (reduced load/rated load)
Enquiries : etc. These motors are well suited for ‘smooth starting’
drives by suitably stepping the starting resistance. The rotor current while starting is proportional
The following information should be included : They can also be used for variable speed drives, to the motor torque and determines the size of
particularly for short periods and within a small speed the starting resistance.
a) Application. range.
Fine speed variation is possible by inserting
b) Voltage and frequency + variations.
resistances in the rotor circuit calculated per
c) Ambient temperature, and type of protection
required.
Additional Mechanical phase as :
71 MC071433 1310 7 0.55 0.75 1310 1.56 2.25 2.75 3.7 0.0033
80 MC080413 1340 10 0.75 1.0 1340 1.80 2.3 2.8 4.5 0.0061
80 MC080433 1385 11 1.1 1.5 1385 2.80 2.8 2.9 5.0 0.0072
90S MC09S433 1395 19 1.5 2 1395 3.70 2.25 2.75 4.7 0.0124
90L MC09L453 1380 23 2.2 3 1380 4.95 2.5 2.8 5.2 0.0158
100L MC10L453 1390 31 3.7 5 1390 7.95 2.7 3.4 6.0 0.0259
112M MC11M453 1430 48 5.5 7.5 1430 12.4 2.9 3.5 6.5 0.0579
132S MC13S453 1410 70 7.5 10 1410 14.8 2.25 2.9 6.5 0.1270
132M MC13M483 1430 84.5 9.3 12.5 1430 18.1 2.7 3.3 6.5 0.1508
160M MC16M413 1460 92 11 15 1460 21.2 2.25 2.8 6.5 0.2511
160M MC16M433 1450 105 15 20 1450 30.7 2.3 2.9 6.5 0.2767
160L MC16L483 1450 132 18.5 25 1450 34.8 2.6 3.2 6.5 0.3767
180L MC18L473 1460 190 22 30 1460 39.5 3.1 2.75 6.0 0.5400
200L MC20L433 1465 266 30 40 1465 52 2.8 2.75 6.0 0.8600
225S MC22S413 1470 338 37 50 1470 64.5 2.7 2.5 6.0 1.3200
225M MC22M433 1470 366 45 60 1470 78.0 2.7 2.5 6.0 1.6000
Note: 4 pole motors upto and including 15kw and 6 pole motors upto and including 9.3 kW are also suitable for 50 C Amb.
0
90S MC09S813 615 17 0.47 0.63 615 2.05 2.25 2.75 3.5 0.011
90L MC09L853 680 20 0.64 0.84 680 2.40 2.25 2.75 3.5 0.014
100L MC10L813 655 28 1.1 1.5 655 3.4 2.25 2.75 3.7 0.023
100L MC10L833 680 32 1.5 2 680 4.95 2.25 2.75 3.7 0.027
112M MC11M813 700 38 2.2 3 700 7.5 2.25 2.75 4.5 0.051
132S MC13S813 645 57 3.2 4.3 645 9.8 2.25 2.75 4.0 0.099
160M MC16M813 720 91 4.45 6 720 14.8 2.25 2.75 4.8 0.217
160M MC16M833 660 106 6.6 8.8 660 17.5 2.25 2.75 5.2 0.299
160L MC16L873 720 130 9.3 12.5 720 21.5 2.25 2.75 6.0 0.400
3
3/9
Bharat Bijlee Limited
Crane & Hoist Duty Motors CC1/B
71 MC071433 1310 7 0.55 1.56 0.55 1.56 0.55 1.56 0.55 1.56 0.55 1.56 0.55 1.56
80 MC080413 1340 10 0.75 1.80 0.75 1.80 0.75 1.80 0.75 1.80 0.75 1.80 0.75 1.80
80 MC080433 1385 11 1.1 2.80 1.1 2.80 1.1 2.80 1.1 2.80 11 2.80 1.1 2.80
90S MC09S433 1395 19 1.5 3.70 1.5 3.70 1.5 3.70 1.5 3.70 1.5 3.70 1.5 3.70
90L MC09L453 1380 23 2.2 4.95 2.2 4.95 2.2 4.95 2.2 4.95 2.2 4.95 2.2 4.95
100L MC10L453 1390 31 3.7 7.95 3.7 7.95 3.7 7.95 3.7 7.95 3.7 7.95 3.7 7.95
112M MC11M453 1430 48 5.5 12.40 5.5 12.40 5.5 12.40 5.5 12.40 5.5 12.40 5.5 12.40
132S MC13S453 1410 70 7.5 14.80 7.5 14.80 7.5 14.80 7.5 14.80 7.5 14.80 7.5 14.80
132M MC13M483 1430 84.5 9.3 18.10 9.3 18.10 9.3 18.10 9.3 18.10 9.3 18.10 9.3 18.10
160M MC16M413 1460 92 11 21.2 11 21.2 11 22.2 11 22.2 11 22.2 11 22.2
160M MC16M433 1450 105 15 30.7 15 30.7 15 30.7 15 30.7 15 30.7 15 30.7
160L MC16L483 1450 132 18.5 34.8 18.5 34.8 18.5 34.8 18.5 34.8 18.5 34.8 18.5 34.8
180L MC18L473 1460 190 22 39.5 22 39.5 22 39.5 22 39.5 22 39.5 20 38
200L MC20L433 1465 266 30 52.0 30 52.0 30 52.0 30 52.0 28 50 25 45
225S MC22S413 1470 338 37 64.5 37 64.5 37 64.5 35 63 - - - -
225M MC22M433 1470 366 45 78.0 45 78.0 45 78.0 44 75 - - - -
Note: 4 pole motors upto and including 15kw and 6 pole motors upto and including 9.3 kw are also suitable for 500 C Amb.
without applying derating factor.
71 MC071633 800 7 0.37 1.43 0.35 1.40 0.37 1.43 0.35 1.4 0.37 1.43 0.35 1.4
80 MC080613 890 10 0.37 1.9 0.37 1.9 0.37 1.9 0.37 1.9 0.37 1.9 0.37 1.9
80 MC080613 830 10 0.55 2.0 0.55 2.0 0.55 2.0 0.55 2.0 0.55 2.0 0.55 2.0
80 MC080633 885 11 0.75 2.4 0.75 2.4 0.75 2.4 0.75 2.4 0.75 2.4 0.75 2.4
90L MC09L6A3 900 22 1.1 2.9 1.1 2.9 1.1 2.9 1.1 2.9 1.1 2.9 1.1 2.9
90L MC09L653 895 22 1.5 4.2 1.5 4.2 1.5 4.2 1.5 4.2 1.5 4.2 1.5 4.2
100L MC10L653 930 32 2.2 6.5 2.2 6.5 2.2 6.5 2.2 6.5 2.2 6.5 2.2 6.5
112M MC11M653 920 43 3.7 9.1 3.7 9.1 3.7 9.1 3.7 9.1 3.7 9.1 3.7 9.1
132S MC13S653 920 65 5.5 14.2 5.5 14.2 5.5 14.2 5.5 14.2 5.5 14.2 5.5 14.2
132M MC13M693 925 79 7.5 18.8 7.3 18.8 7.5 18.8 7 18.8 7.5 18.8 6.8 17
160M MC16M633 950 102 9.3 19.2 9.3 19.2 9.3 19.2 9.3 19.2 9.3 19.2 9.3 19.2
160L MC16L663 960 119 11 24 11 24 11 24 11 24 11 24 11 24
160L MC16L673 940 129 15 33 14.5 33 15 33 14.5 33 15 33 14.0 32
200L MC20L613 975 234 18.5 34 18.5 34 18.5 34 18.5 34 18.5 34 18 34
200L MC20L633 975 251 22 40.5 22 40.5 22 4.05 22 40.5 22 40.5 21 40
225M MC22M633 975 341 30 53 30 53 30 53 30 53 28 51 26 50
4
4/9
Bharat Bijlee Limited
Crane & Hoist Duty Motors CC1/B
112M MP11M413 3.6 4.8 1290 9.3 25.8 3.1 4.1 1325 8.2 20.7
112M MP11M433 4.2 5.6 1340 9.7 20.9 3.6 4.8 1370 8.6 18.7
132M MP13M413 5.7 7.6 1310 13.4 31.2 5 6.7 1350 11.4 27.2
112M MP11M623 2.4 3.2 840 6.4 20.5 2.1 2.8 870 6 17.1
112M MP11M643 3.3 4.4 850 8.6 20.5 2.8 3.7 880 8.2 17
132M MP13M663 5.5 7.3 895 13.3 26.5 4.8 6.4 915 12.4 23
160M MP16M613 7.5 10.00 910 16.9 31.3 6.5 8.7 920 14.7 27.2
160L MP16L653 9.5 12.70 915 21.0 28 8.5 11.4 930 18.5 24
5
5/9
Bharat Bijlee Limited
Crane & Hoist Duty Motors CC1/B
Stator
Rotor
Stator
Stator
Rotor
Rotor
Stator
Rotor
Rotor
Load
Torque Torque Torque kg.
Torque
100L MP10L413 1.8 1200 1.85 4.7 23.5 1.5 1280 2.3 4.0 18.0 1.3 1320 2.8 3.7 14.5 1.1 1360 3.4 3.4 12.0 70 0.03 0.08 37
100L MP10L433 2.5 1200 1.85 6.6 26.0 2.5 1200 1.85 6.6 26.0 2.2 1255 2.2 5.7 21.0 1.5 1365 3.5 4.1 12.5 85 0.035 0.09 40
60 Starts per hour
112M MP11M413 4.1 1200 2.0 10.5 32.0 3.6 1290 2.4 9.3 25.8 3.1 1325 2.9 8.2 20.7 2.2 1380 4.3 7.1 14.0 110 0.48 0.12 58
112M MP11M433 5.0 1300 2.2 11.2 27.0 4.2 1340 2.7 9.7 20.9 3.6 1370 3.3 8.6 18.7 3.0 1390 4.0 8.0 15.5 140 0.056 0.14 61
132M MP13M413 6.0 1300 2.0 14.7 33.0 5.7 1310 2.1 13.4 31.3 5.0 1350 2.4 11.4 27.2 4.0 1410 3.2 9.1 21.0 130 0.090 0.22 90
132M MP13M463 8.3 1365 2.0 18.5 32.3 7.5 13752.2 17.0 29.0 6.4 1410 2.6 14.6 23.7 5.5 1420 3.1 13.2 20.0 180 0.14 0.35 94
100L MP10L413 1.7 1240 2.0 4.5 21.5 1.4 1300 2.6 3.9 16.5 1.3 1320 2.8 3.7 14.5 1.1 1360 3.4 2.4 12.0 70 0.03 0.08 37
100L MP10L433 2.5 1200 1.85 6.6 26.0 2.4 1220 2.0 6.3 24.0 2.1 1265 2.3 5.4 20.0 1.5 1365 3.5 4.1 12.5 85 0.035 0.09 40
150 Starts per hour
112M MP11M413 4.1 1200 2.0 10.5 32.0 3.5 1295 2.5 9.0 24.5 .3.0 1330 3.0 8.1 20.0 2.2 1380 4.3 7.1 14.0 110 0.048 0.12 58
112M MP11M433 4.7 1315 2.4 10.6 24.6 4.0 1350 2.9 9.4 19.5 3.5 1375 3.4 8.4 18.5 3.0 1390 4.0 8.0 15.5 140 0.056 0.14 61
132M MP13M413 6.0 1300 2.0 14.7 33.0 5.4 1325 2.2 12.3 29.4 4.7 1365 2.6 10.8 25.6 4.0 1410 3.2 9.1 21.0 130 0.09 0.22 90
132M MP13M463 7.2 1390 2.3 16.2 27.5 6.3 1415 2.7 14.4 23.3 5.6 1420 3.0 13.4 20.3 5.0 1430 3.4 10.9 18.2 180 0.14 0.35 94
100L MP10L413 1.6 1260 2.2 4.3 20.0 1.3 1320 2.8 3.7 14.5 1.2 1340 3.1 3.6 13.5 1.0 1380 3.8 3.3 10.5 70 0.03 0.08 37
100L MP10L433 2.5 1200 1.85 6.6 26.0 2.3 1240 2.1 6.0 22.5 2.6 1280 2.5 5.1 18.5 1.5 1365 3.5 4.1 12.5 85 0.035 0.09 40
300 Starts per hour
112M MP11M413 3.9 1250 2.2 9.9 29.4 3.3 1310 2.7 8.5 22.0 2.8 1345 3.3 7.8 18.3 2.2 1380 4.3 7.1 14.0 110 0.048 0.12 58
112M MP11M433 4.1 1345 2.8 9.6 20.2 3.5 1375 3.4 8.4 18.5 3.2 1385 3.7 8.2 16.7 2.8 1400 4.3 7.8 14.3 140 0.056 0.14 61
132M MP13M413 5.5 1320 2.2 12.5 30.0 4.8 1360 2.6 11.0 26.1 4.3 1390 2.9 9.9 23.0 3.9 1415 3.3 9.0 20.3 130 0.09 0.22 90
132M MP13M463 5.5 1420 3.1 13.2 20.0 5.0 1430 3.4 10.9 18.2 4.5 1435 3.8 10.3 16.4 4.2 1440 4.1 9.9 15.3 180 0.14 0.35 94
6
6/9
Bharat Bijlee Limited
Crane & Hoist Duty Motors CC1/B
Stator
Rotor
Stator
Stator
Rotor
Rotor
Stator
Rotor
Rotor
Load
Torque Torque Torque Torque kg.
100L MP10L613 1.3 800 1.75 3.8 17.0 1.1 850 2.2 3.5 13.0 1.0 870 2.5 3.4 12.0 0.75 900 3.4 3.2 8.5 65 0.034 0.09 37
100L MP10L623 1.9 785 2.0 5.4 18.5 1.5 870 2.8 5.0 13.0 1.3 890 3.3 4.7 11.0 1.1 910 4.0 4.4 9.5 80 0.038 0.1 40
112M MP11M623 2.6 820 2.0 9.8 22.5 2.4 840 2.2 6.4 20.5 2.1 870 2.7 6.0 17.1 1.5 910 3.9 4.8 12.5 90 0.068 0.17 58
60 Starts per hour
112M MP11M643 3.8 830 2.0 9.6 23.5 3.3 850 2.3 8.6 20.5 2.8 880 2.8 8.2 17.0 2.2 900 3.7 7.5 13.5 115 0.076 0.19 61
132M MP13M613 4.8 860 2.1 12.5 32.5 4.0 890 2.6 11.0 26.0 3.4 905 3.0 9.7 21.0 3.0 920 3.5 9.0 18.0 110 0.153 0.38 90
132M MP13M663 6.6 870 1.9 16.0 35.0 5.5 895 2.5 13.3 26.5 4.8 915 2.9 12.4 23.0 4.0 930 3.6 11.0 18.0 140 0.18 0.45 94
160M MP16M613 8.0 900 2.0 18.1 33.0 7.5 910 2.1 16.9 31.3 6.5 920 2.5 14.7 27.2 6 930 2.7 13.4 25.0 165 0.31 0.77 129
160L MP16L653 11.5 890 1.6 25.3 46.2 10.0 910 1.8 22.0 28 9.0 920 2.1 19.8 25.2 7.5 940 2.5 16.5 21.0 240 0.378 0.94 139
100L MP10L613 1.3 800 1.75 3.8 17.0 1.1 850 2.2 3.5 13.0 1.0 870 2.5 3.4 12.0 0.75 900 3.4 3.2 8.5 65 0.034 0.09 37
100L MP10L623 1.8 810 2.2 5.3 17.0 1.5 870 2.8 5.0 13.0 1.3 890 3.3 4.7 11.0 1.1 910 4.0 4.4 9.5 80 0.038 0.1 40
112M MP11M623 2.6 820 2.0 6.8 22.5 2.3 850 2.4 6.2 19.5 2.0 875 2.8 5.9 16.0 1.5 910 3.9 4.8 12.5 90 0.068 0.17 58
150 Starts per hour
112M MP11M643 3.8 830 2.0 9.6 23.5 3.2 855 2.4 8.5 20.0 2.7 885 3.0 8.1 16.5 2.2 900 3.7 7.5 13.5 115 0.076 0.19 61
132M MP13M613 4.5 865 2.2 11.9 30.0 3.7 895 2.8 10.4 23.5 3.2 915 3.3 9.4 19.5 2.8 930 3.8 8.7 16.5 110 0.153 0.38 90
132M MP13M663 6.5 870 2.0 15.1 34.0 5.4 895 2.7 13.2 25.0 4.6 920 3.0 12.0 22.0 3.9 935 3.7 10.0 17.5 140 0.18 0.45 94
160M MP16M613 8.0 900 2.0 18.1 33.0 7.0 920 2.3 15.8 29 6.0 930 2.7 13.4 25 5.5 940 2.9 12.3 23.0 165 0.31 0.77 129
160L MP16L653 10.5 900 1.8 23.1 29.4 9.5 915 1.9 21.0 28 8.6 930 2.25 18.5 24 7.5 940 2.5 16.5 21.0 240 0.378 0.94 139
100L MP10L613 1.3 800 1.75 3.8 17.0 1.1 850 2.2 3.5 13.0 0.9 890 2.8 3.3 10.5 0.75 900 3.4 3.2 8.5 65 0.034 0.09 37
100L MP10L623 1.8 810 2.2 5.3 17.0 1.5 870 2.8 5.0 130. 1.3 890 3.3 4.7 11.0 1.1 910 4.0 4.4 9.5 80 0.038 0.1 40
112M MP11M623 2.6 820 2.0 6.8 22.5 2.3 850 2.4 6.2 19.5 1.9 880 3.0 5.7 15.0 1.5 910 3.9 4.8 12.5 90 0.068 0.17 58
300 Starts per hour
112M MP11M643 3.6 840 2.1 9.2 22.0 3.0 870 2.6 8.3 18.5 2.6 890 3.1 8.0 16.0 2.2 900 3.7 7.5 13.5 115 0.076 0.19 61
132M MP13M613 4.0 890 2.6 11.0 26.0 3.4 905 3.0 9.7 21.0 3.0 920 3.5 9.0 18.0 2.6 935 4.1 8.2 15.0 110 0.153 0.38 90
132M MP13M663 6.1 875 2.2 14.6 30.0 5.1 900 2.7 12.5 24.0 4.4 930 3.2 11.5 20.5 3.7 935 3.8 9.7 15.8 140 0.18 0.45 94
160M MP16M613 6.7 920 2.4 15.2 28.0 5.5 940 2.9 12.3 23 5.0 945 3.2 11.2 21 4.5 950 3.5 10 18.8 165 0.31 0.77 129
160L MP16L653 9.0 920 2.1 19.8 25.2 8.0 935 2.4 17.4 22.6 7.5 940 2.5 16.5 21 5.5 950 3.4 12.1 15.4 240 0.378 0.94 139
7
7/9
Bharat Bijlee Limited
Crane & Hoist Duty Motors CC1/B
IEC
Fr. Size Motor Type B* A* HA BB AB AC AD H* L LC BA AA HD HC K S V C CA X X. D,DA* E,EA GA,GC* F FA* I.I 1 , m 1m 1 d5mm
100l MP10L _ _ 3 140 160 14 245 200 202 61 100 488 570 40 50 262 201 13 16 210 63 247 36 171 28 60 31 8 55 3 M10X20
112M MP11M_ _ 3 140 190 15 176 230 227 63 112 537 620 50 62 292 226 13 16 231 70 290 36 186 28 60 31 8 55 3 M10X20
132M MP13M _ _ 3 178 216 17 218 256 267 74 132 612 715 54 64 328 266 13 17 267 89 288 42 185 38 80 41 10 70 5 M12X28
160M MP16M/L _ 3 254 254 20 294 314 324 88 160 730 866 70 60 374 322 15 19 313 105 287 56 219 42 110 45 12 105 3 M16X32
Tolerance on Dimernsions Marked* (I.S.A. FIT) Also Suitable for mounting arrangement B6; B7; B8; V5 & V6
as per IS 2253
DIMENSIONS TOLERANCES
Note : Dimension details for motors of other type of constructions
B,A ±0.75 will be made available on enquiry.
H 0.5 IS 1231
D, DA 28Ø j6, 38Ø, 42Ø k6
GA, GC; FFA IS 2048
D5 + centering to IS 2540
8
8/9
Bharat Bijlee Limited
Crane & Hoist Duty Motors CC1/B
Offices
REGION CITY ADDRESS PHONE FAX
NORTH NEW DELHI Milap Niketan, 4th floor 2371 14 34 011-2331 9413
8A, Bahadur Shah Zafar Marg, New Delhi 110 002. 2331 96 94 /95/96
LUDHIANA 7, Gian Market, Opp. Ramgarhia Gurudwara, 2531 663 0161-2533826
G. T. Road, Miller Ganj, Ludhiana - 141 003. 2542 131
INDORE C/o. Tirupati Engineering, 128, 3rd Floor, 2704 474 0731-2704390
Dawa Bazar, RNT Marg, Indore 452 001. 2704 486
EAST KO L K ATA Flat No.8, 'Mansarowar', 2nd Floor, 3B Camac Street, 2217 23 82 033-2217 2467
Kolkata 700 016. 2217 23 83/ 84
AHMEDABAD 202, Arth, 8-Rashmi Society, Behind A. K. Patel House, 2642 76 67 079-2656 3581
Mithakhali, Cross Road, Ahmedabad - 380 009. 2643 08 98
SOUTH BANGALORE 204-207, Ramanashree Chambers, 2nd Floor, 559 26 81 080-559 2823
No.37, Lady Curzon Road, Bangalore 560 001. 559 21 37
559 62 74
CHENNAI C/o. Arpan Corporation, AVM Studios Compound, 2372 85 79 044-2372 8579
38, Arcol Road, Vadapalani, Chennai 600 026. 2472 67 34
SECUNDERABAD Krishna Mansion, 2nd Floor, Adjacent to Bible House, 2753 45 12 040-2753 1791
134, Rashtrapati Road, Secunderabad 500 003.
9
9/9