Professional Documents
Culture Documents
Horizon DW CLI Commands
Horizon DW CLI Commands
Horizon DW CLI Commands
get redundancy link monitor parameters get redundancy mode get redundancy override get redundancy partner information get redundancy secondary enet state get redundancy status
get rls get rls link enable get rls link monitor parameters
DragonWave Inc.
178 get rls link control get rls make rsl get rls signal fault parameters get rls status get rsl threshold get sessions get snmp access mode get snmp managers get snmp set request get snmp traps get snmp trap hosts get snmpv3 managers get snmpv3 trap hosts get snr threshold get sntp get sntp offset get ssh server get ssh server fingerprint get ssl certificate status get subnet mask get super user get sw inventory get sw version get system licensed speed downgrade information get system mode get system speed get system summary get system redundancy get telnet access get traffic statistics get transmit power get unique peer authentication key get user accounts get user session get vlan tag get vlan tagging get web server kill ssh sessions list [ftp:file/directory/] lo ping [-w timeout][-n count][-t][ip address] reset [system / modem] save config [ftp:filename] save log [ftp:filename] save ecfmmib save mib save performance log [ftp:filename] save users [ftp:filename] set aam [state<on/off>][inter mode<on/off>] [max Tx-Pwr<on/off>] set aam mode [system mode name|default] set admin user set air interface authentication type [type] set authentication failure [action] set alarms counter [0] set alignment [on/off] set antenna diameter [index of diameter] set atpc [on|off][coordinated power] set bandwidth utilization threshold [threshold][time] set cos default value [0-7] set cos expedite queue [on|off] set cos qinq itag [protocol id] set cos qinq otag [protocol id] set cos queue cir [0-100,0-100,0-100,1-100] set cos queue mapping [mapping] set cos queue cbs set cos type [cos_vlan|cos_qinq_itag|cos_qinq_otag|cos_dscp| cos_mplsexp] set cos wfq weight [w1 w2 w3 w4] set current channel index set date time [dd/mm/yyyy hh:mm:ss:ms] set default gateway [ip address] set dropped frames threshold [threshold][time] set dw access <on/off> set ecfm set ecfm associate vlan-id set ecfm cc enable level set ecfm cc level set ecfm ccm-unicast-mac set ecfm default-domain global set ecfm default-domain vlan set ecfm domain set ecfm error-log set ecfm mep archive-hold-time set ecfm mep-capability level set ecfm mep crosscheck mpid set ecfm mep crosscheck start-delay set ecfm mep level set ecfm mip ccm-database caching set ecfm mip ccm-database size set ecfm mip ccm-database hold-time set ecfm mip dynamic evaluation set ecfm mip level set ecfm oui set ecfm port set ecfm service set ecfm start set ecfm traceroute cache set ecfm traceroute cachesize set ecfm traceroute cache holdtime set ecfm y1731 set enet config [port1|port2] set enet speed [port1|port2] speed[10|100|1000|auto] AutoNeg[auto] set group authentication key [key] set http secure access [Admin|Noc|Super] [on|off] set ip address [address] set logging [on|off] set maximum frame size [1600-9600] set network management interface [port1|port2| port2 extended] set network protocol strict [on|off] set noc user set optical transmitter state [on|off] set pause state [on|off] set performance logging [on|off] set performance log interval [hr:min:sec] set programmed frequency [index] set qos [on|off] set qos policy [strict_priority|wfq] set radio transmitter state [enable|disable] set radio band [band] set radio loopback [on|off]