Professional Documents
Culture Documents
Hitech Procedure: Lathe How To Check Skip Signal On A Lambda10L
Hitech Procedure: Lathe How To Check Skip Signal On A Lambda10L
Hitech Procedure: Lathe How To Check Skip Signal On A Lambda10L
SV03-999-71-001 1/ 10
In case machine does not touch sensor but the skip signal is ON (beep sounds) 1. Press FR/BK -> F4 (SYSTEM) -> Select 2. DIAGNOSE -> Press INPUT ->Select 3. RELEVENT TO SERVO -> Press INPUT -> Press PAGE DOWN -> You will see RELEVENT TO SERVO 2/2 screen. 2. Check Skip Signal On diagnostic.
0 : Skip Signal already OFF. Try to touch sensor again, then check Skip Signal. 1 : Skip Signal is ON from Skip Board. Go to next step.
All Skip Signal is OFF Skip board does not output signal. Go to step 4.
No.1 sensor (LED) ~ No.8 sensor (LED) is Normal closed (not touch skip off = close / touch skip on = open). No.9 sensor (LED) and No.10 sensor (LED) is Normal open (not touch skip off = open / touch skip on = open)
HITECH
4. Check VID board.
SV03-999-71-001 2/ 11
1 2
4-1. Disconnect skip cable CN3 of VID board. 4-2. Check Skip signal on diagnostic screen. 0 = VID board is OK / 1 = VID board is No Good. 4-3. Turn off NC power. 4-4. Connect CN3-pin1 to 24V, CN3-pin2 to 0V by temporary cable. (24V and 0V is in terminal.) 4-5. Turn on NC power. 4-6. Check Skip signal on diagnostic screen. 0 = VID board is No good / 1 = VID board is Good. VID board is OK -> Change Skip board. VID board is No good -> Change VID board
5. Check skip input signal. Example1 : LED1 is ON. 5-1. Turn off NC power. 5-2. Connect CN1-pin1 to 24V, CN1-pin2 to 0V by temporary cable. 5-3. Turn on NC power. 5-4. Check LED1. ON = Skip board is No good / OFF = Skip board is Good. Example2 : LED9 is ON. 5-5. Turn off NC power. 5-6. Disconnect CN1-pin17. 5-7. Turn on NC power. 5-8. Check LED9. ON = Skip board is No good / OFF = Skip board is Good. Skip board is OK -> Change Skip sensor or Check Wiring to sensor. Skip board is No good -> Change Skip board Skip board CN1-pin1 + CN1-pin2 CN1-pin3 + CN1-pin4 CN1-pin5 + CN1-pin6 CN1-pin7 + CN1-pin8 CN1-pin9 + CN1-pin10 CN1-pin11 + CN1-pin12 -
No.1 Sensor (NC) No.2 Sensor (NC) No.3 Sensor (NC) No.4 Sensor (NC) No.5 Sensor (NC) No.6 Sensor (NC)
CN1-pin13 CN1-pin14 CN1-pin15 CN1-pin16 CN1-pin17 CN1-pin18 CN1-pin19 CN1-pin20 CN1-pin21 CN1-pin22 CN1-pin23 CN1-pin24
+ + + + 24V 24V 0V 0V
No.7 Sensor (NC) No.8 Sensor (NC) No.9 Sensor (NO) No.10 Sensor (NO)
HITECH
SV03-999-71-001 3/ 11
In case the machine is touching the sensor, but the skip signal is still OFF (Machine doesnt stop) 1. Press FR/BK -> F4 (SYSTEM) -> Select 2. DIAGNOSE -> Press INPUT ->Select 3. RELEVENT TO SERVO -> Press INPUT -> Press PAGE DOWN -> You will see RELEVENT TO SERVO 2/2 screen. 2. Touch hold sensor , then Check Skip Signal ON diagnostic.
0 : Skip signal still OFF. Go to next step. 1 : Skip signal is ON. from skip board. Skip signal turn on. No problem. Check NC program.
3. Touch hold sensor , then Check LED on skip board. LED light or dark.
No.1 sensor (LED) ~ No.8 sensor (LED) is Normal closed (not touch skip off = close / touch skip on = open). No.9 sensor (LED) and No.10 sensor (LED) is Normal open (not touch skip off = open / touch skip on = open) 4. Check VID board. 4-1. Disconnect skip cable CN3 of VID board. 4-2. Check Skip signal on diagnose screen. 0 = VID board is OK / 1 = VID board is No Good. 4-3. Turn off NC power. 4-4. Connect CN3-pin1 to 24V , CN3-pin2 to 0V by temporary cable. (24V and 0V is in terminal.) 4-5. Turn on NC power. 4-6. Check Skip signal on diagnose screen. 0 = VID board is No good / 1 = VID board is Good. VID board is OK -> Change Skip board. VID board is No good -> Change VID board
1 2
HITECH
SV03-999-71-001 4/ 11
5. Check skip input signal. (Make sure of which sensor input number by wiring Diagram.) Example 1 : No.1 Sensor. 5-1. Turn off NC power. 5-2. Disconnect CN1-pin1. 5-3. Turn on NC power. 5-4. Check LED1. ON = Skip board is Good / OFF = Skip board is No good. Example 2 : No.9 Sensor. 5-5. Turn off NC power. 5-6. Connect CN1-pin17 to 24V , CN1-pin17 to 0V by temporary cable.. 5-7. Turn on NC power. 5-8. Check LED9. ON = Skip board Good / OFF = Skip board is No good. Skip board is OK -> Change Skip sensor or Check Wiring to sensor. Skip board is No good -> Change Skip board
Finished
HITECH
SV03-999-71-001 5/ 11
CA20II
HITECH
SV03-999-71-001 6/ 11
HT25G
HITECH
HT20RIII
SV03-999-71-001 7/ 11
HITECH
SV03-999-71-001 9/ 11
HITECH
SV03-999-71-001 10/11
HITECH
SV03-999-71-001 11/11