0
ICOM
aA
MANUAL
HF/VHF TRANSCEIVER
IC—7O6MKI
Icom Inc.INTRODUCTION
This service manual describes the latest service information
for the IC-706MK Il HF/VHF TRANSCEIVER at the time of
publication.
VERSION NO
To upgrade quality, any electrical or mechanical parts and
internal circuits are subject to change without notice or
‘obligation,
DANGER
NEVER connect the transceiver to an AC outlet or to a OC
power supply that uses more than 16 V. This will ruin the
transceiver.
DO NOT expose the transceiver to rain, snow or any liquids.
DO NOT reverse the polarities of the power supply when
connecting the transceiver.
DO NOT apply an RF signal of more than 20 dBm (100 mW)
to the antenna connector. This could damage the
transceiver's front end.
ORDERING PARTS
REPAIR NOTES
Be sure to include the following four points when ordering
replacement parts:
1, 10-digit order numbers
2. Component part number and name
3. Equipment model name and unit name
4. Quantity required
SAMPLE ORDER>
1110004080 SIC uPC270ST ——IC-TOBMK IE MAIN UNIT 5 pieces
8810009029 Screw FH M2.6x5ZK IG-70SMK I Top cover 10 pieces
Addresses are provided on the inside back caver for your
convenience.
1, Make sure a problem is internal before disassembling the
transceiver.
2, DO NOT open the transceiver until the transceiver is
disconnected from its power source.
3. DO NOT force any of the variable components. Turn
them slowly and smoothly.
4. DO NOT short any circuits or electronic parts. An
insulated tuning tool MUST be used for all adjustments.
5. DO NOT keep power ON for a long time when the
transceiver is defective.
6. DO NOT transmit power into a signal generator or a
sweep generator.
7. ALWAYS connect a 50 dB to 60 dB attenuator between
the transceiver and a deviation meter or spectrum
analyzer when using such test equipment.
8. READ the instructions of test equipment thoroughly
before conriecting equipment to the transceiver.SECTION
‘SECTION
‘SECTION
‘SECTION
‘SECTION
‘SECTION
SECTION
SECTION
SECTION
SECTION
TABLE OF CONTENTS
1. SPECIFICATIONS
2 INSIDE VIEWS
3 CIRCUIT DESCRIPTION
3-1 RECEIVER CIRCUITS
3-2 TRANSMITTER CIRCUITS......
3-3 PLLCIRCUITS
3-4 LOGIC CIRCUITS...
4 ADJUSTMENT PROCEDURES
4-1 PREPARATION BEFORE SERVICING ...
4-2 PLL ADJUSTMENT
4-3 RECEIVER ADJUSTMENT
4-4 TRANSMITTER ADJUSTMENT
4-5 METER ADJUSTMENT
5 PARTS LIST
6 MECHANICAL PARTS AND DISASSEMBLY
7 SEMI-CONDUCTOR INFORMATION
8 BOARD LAYOUTS
8-1 DISPLAY BOARD . 8-1
8-2 MAIN BOARD...
8-3 PLLUNIT
8-4 PAUNIT ronun
8-5 FILTER BOARD.
9 BLOCK DIAGRAM
10 VOLTAGE DIAGRAMSECTION 1 SPECIFICATIONS
GENERAL @ RECEIVER
= Frequency coverage + Rect syiom
Receive 0.030 ~ 200.000 MHz" SSBICWIAMWFM Double superheterodyne
Transm 3900-00 Mi aw “Tile pentane
300-9900 Ma: +niomediat roqueries
10100= s0te0 une itoDE [i a a
ies teal “SSB/FM | 68.0115 MHz | SO11S MHz | 455 kKHZ
‘ose asa TAWEUENT 60.0700 Mr | @ 700 Miz | ABB WA
ee OW eB oT06 Wiz [9.08 Me [
28.000 — 29.700 Bry 690105 wre [8.0105 Mi [
$0.00 ~ 64000 Ne: WE] 70.00 | 7.7000 | ———
euominponvnen ‘tito BCOMME oe