Professional Documents
Culture Documents
12H Global Motor Grader
12H Global Motor Grader
Engine The Cat C-9 engine is designed and rated to handle the tough loads. The Variable Horsepower option maximizes response, power, and efficiency, while the direct drive, power shift transmission optimizes blade control and versatility. Power Train The power shift transmission takes full advantage of the powerful C-9 engine. Variable Horsepower uses specific torque curves for each gear range for optimum performance. Dual air system and multi-disc oil brakes assure reliable braking control. Hydraulics The load-sensing hydraulic system lowers power consumption and system heat. The advanced PPPC control valves provide low lever effort, balanced flow and consistent cylinder speeds for outstanding blade control. Blade float is incorporated into the blade lift valves. Drawbar, Circle, Moldboard Flexible moldboard positioning and a long wheelbase improve material handling. Rugged construction and replaceable wear parts minimize operation costs. Structures The 12H frame is designed and built to exceed the expectations of the customer. Serviceability Caterpillar re-engineered inspection and service points, grouping them into a convenient left-hand side, ground level 'service center.' Ground level fueling and extended engine and hydraulic oil change intervals help minimize downtime. Operator's Station Low effort blade controls, electronic throttle control, EMS III monitoring system, and improved ventilation provide world-class operator control and comfort. Excellent front and rear visibility can increase operator confidence and productivity.
Straight Blades
Environmentally Responsible Design New engine arrangements and operator station designs reduce emissions to meet current and anticipated regulations for interior and exterior sound levels, emissions, exhaust. Customer Support Your Cat dealer offers a range of services that help you operate longer with lower costs.
Hydraulic System
Circuit type Pump type Pump output Maximum system pressure Standby Pressure Pump output measured @ 1850 RPM Closed center load sense Variable piston 196 L/min 51.9 gal/min 24 150 kPa 3500 psi 3100 kPa 450 psi
Operating Specifications
Top Speed - Fwd. Top Speed - Rev. Turning radius (outside front tires) Steering range - left/right Articulation angle - left/right Fwd. 1st Fwd. 2nd Fwd. 3rd Fwd. 4th Fwd. 5th Fwd. 6th Fwd. 7th Fwd. 8th Rev. 1st Rev. 2nd Rev. 3rd Rev. 4th Rev. 5th Rev. 6th 44 kph 34.7 kph 7.4 m 50 20 3.8 kph 5.1 kph 7.4 kph 10.3 kph 16.2 kph 22 kph 30.3 kph 44 kph 3 kph 5.6 kph 8.1 kph 12.8 kph 23.9 kph 34.7 kph 27.4 mph 21.6 mph 24.25 ft 50 20 2.3 mph 3.2 mph 4.6 mph 6.4 mph 10 mph 13.7 mph 18.8 mph 27.4 mph 1.8 mph 3.5 mph 5 mph 7.9 mph 14.8 mph 21.6 mph
Net power advertised is the power available at rated speed of 2000 rpm, measured at the flywheel when engine is equipped with fan, air cleaner, muffler and alternator. No derating required up to 3048 m (10,000 ft) altitude. Deration rate of 1.5% per 304.8 m (1000 feet) above 3048 m (10,000 feet). Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 standards in effect at the time of manufacture. VHP is an optional arrangement.
Service Refill
Fuel Capacity Cooling system Hydraulic system - total Hydraulic system - tank Engine Oil Differential / Final Drives Tandem housing (each) Front wheel spindle bearing housing Circle drive housing 378 L 44 L 74 L 38 L 24 L 47 L 64 L .5 L 7L 100 gal 11.6 gal 19.5 gal 9.9 gal 6.3 gal 12.2 gal 16.9 gal .13 gal 1.8 gal
Power Train
Forward/Reverse Gears Transmission Brakes - Service Brakes - Service, surface area Brakes - Parking Brakes - Secondary 8 fwd / 6 rev Direct drive, power shift Air actuated multiple oil disc 23 948 cm2 3712 in2 Air-actuated, multiple oil-disc Dual circuit
Brakes meet the following standards: SAE J/ISO 3450 JAN 98.
Moldboard
Blade Width Moldboard Height Thickness Arc radius Throat clearance Cutting edge - width Cutting edge - thickness End Bit - width End Bit - thickness Blade Pull - max GVW Blade Pull - base GVW Down Pressure - max GVW Down Pressure - base GVW 3658 mm 610 mm 22 mm 413 mm 120 mm 152 mm 16 mm 152 mm 16 mm 13 094 kg 9379 kg 10 799 kg 6555 kg 12 ft 24 in .87 in 16.25 in 4.7 in 6 in .63 in 6 in .63 in 28,867 lb 20,677 lb 23,800 lb 14,447 lb
Blade Pull calculated at 0.9 traction coefficient, which is equal to ideal no-slip conditions, and Gross Vehicle Weight (GVW).
Tandems
Height Width Sidewall thickness - inner Sidewall thickness - outer Drive chain pitch Wheel axle spacing Tandem oscillation - forward Tandem oscillation - reverse 506 mm 201 mm 16 mm 18 mm 51 mm 1522 mm 15 25 19.9 in 7.9 in .63 in .71 in 2 in 60 in 15 25
Blade Range
Circle centershift-right Circle centershift - left Moldboard sideshift - right Moldboard sideshift - left Maximum blade position angle Blade tip range (forward) Blade tip range (backward) Maximum shoulder reach outside of tires - right Maximum shoulder reach outside of tires - left Maximum lift above ground Maximum depth of cut 728 mm 752 mm 660 mm 524 mm 90 40 5 1809 mm 1859 mm 480 mm 735 mm 28.7 in 29.6 in 26 in 20.6 in 90 40 5 71.2 in 73.6 in 18.9 in 28.9 in
Ripper
Ripping depth, maximum 462 mm Ripper shank holders 5 Ripper shank holder spacing - min 533 mm Penetration force 8047 kg Pryout force 9281 kg Machine length increase, beam raised 970 mm 18.2 in 21 in 17,740 lb 20,460 lb 38.2 in
Dimensions
Height - low profile cab Height - high profile cab Height - no cab Length - counterweight to ripper Width - Outside front tires Length - front axle to mid tandem Length - front tire to end of rear frame Length - front axle to moldboard Length - between tandem axles Width - outside rear tires Width - tire center lines Height to axle Height to exhaust stack Height to top of cylinders Ground clearance at trans. case 3107 mm 3332 mm 3090 mm 10 012 mm 2440 mm 6086 mm 8571 mm 2575 mm 1523 mm 2422 mm 2077 mm 594 mm 3090 mm 3030 mm 342 mm 122 in 131 in 122 in 394.2 in 96 in 239.6 in 337.4 in 101.3 in 59.9 in 95.3 in 81.8 in 23.4 in 122 in 119 in 13.5 in
4.6 in 71 in 12.5 in
Weights
Gross Vehicle Wt, max - total Gross Vehicle Wt, max - front axle Gross Vehicle Wt, max - rear axles Gross Vehicle Wt, base - total Gross Vehicle Wt, base - front axle Gross Vehicle Wt, base - rear axles 20 783 kg 6234 kg 14 549 kg 14 200 kg 3784 kg 10 416 kg 45,818 lb 13,744 lb 32,074 lb 31,320 lb 8346 lb 22,974 lb
Base operating weight calculated on standard machine configuration with 13.00-24 10PR (G-2) tires, full fuel tank, coolant, lubricants and operator.
Materials and specifications subject to change without notice. Featured machines in photo may include additional equipment. For more complete information on Cat products, dealer services, and industry solutions, visit us on the web at www.cat.com. 2004 Caterpillar All Rights Reserved.
Product ID: 12H Global