Professional Documents
Culture Documents
Ilford Film Processing Chart: Plus Plus Plus PRO Professional Professional 200
Ilford Film Processing Chart: Plus Plus Plus PRO Professional Professional 200
20C/68F
EI
PAN F PLUS
25 50 50
FP4 PLUS
125 200 250 320
HP5 PLUS
400 800 1600 3200
DELTA1 00 PRO
50 100 200 200 250
SFX 200
400 800
10
12 1 0 15
10
1 3
20 91/2 1 2 7 1 0
1 4
6 7 10 18 4
8 91/2 14
6 7
7 8
91/2 121/2 17 17
10 10 17
14 14 18
71/2 10 1/2 1 4 1 1 3 6 20
12 /
81/2 1 1/2 0 1 1 1 3
91/2 1 1/2 13 0
1 1
121/2 15 17 20 4 4 6 8 4 4 51/2 4 6 9 10
12 /
15 20 5 71/2 1 4 7
12 /
ILFOTEC HC
1+15 1+31
5 9 5 9
1 1 5 1 1 5 6 8 5 6 8 5
5 6 71/2
13
5 9
7 13 7
101/2 19 101/2
61/2 91/2 5
9 141/2 5 8 13
ILFOTEC LC29
1/2
13 6 71/2
5 9 11
8 12 6
12 /
61/2 91/2 14 9
10 131/2 17 14
9 141/2
13 19
ILFOSOL S
1+9 1+14
12 /
7 91/2
14
12 /
6 1 0 6
12 /
12 /
1/2
8 10
1/2
13
71/2 91/2 8 1 0 1 4 9 1 3 1 2 1 5 9 14 18 1 3 1 8 25 6 13 20 9 1 5 20 6 12
1 4 8 11 1 6
61/2
10 8 5
MICROPHEN
12 /
12 /
12 /
12 /
1 0
12 /
1 4
12 1 6
12 /
12 /
6 11 14 1 5
12 15 23 12 13
10 14 81/2 14 20 16 1 5 1 7 1 0 1 2
12 /
151/2 19
PERCEPTOL
12 1 5
12 /
11
13
1 5
1 8
141/2 20
15 17 17 21 4 6 11 41/2 61/2 6 12
1/ 2
ACUFINE RODINAL
9 9 20 91/2 1 4
11
13
16 51/2 7 9 1 1 20
9 1 5 6 9 1 4 8 1 1 1 6 41/2
7 10 7 91/2 1 4
9 1 4 9 1 2 22
D -76
91/2 1 1/2 13 0
1 7
81/2 1 5
1 3
5 6 7
12 /
8
12 /
13
5 9
9 1 5
1 1
5 1 2
6 1 5
1 1 0 3
12 /
9 1 4
DEVELOPMENT TIMES Follow the recommended times in the chart for the film/developer combination of your choice. CAUTION: These times are intended as a guide only. Times shorter than 5 minutes may lead to uneven development. AGITATION For manual processing in spiral tanks and deep tanks, the development times are based on intermittent agitation. With spiral tanks, invert the tank four times during the first 10 seconds, then invert the tank four times again during the first 10 seconds for each further minute. Where continuous agitation is used for manual processing (as in a dish/tray or with some types of developing tank), reduce these times by up to 15%. For use in rotary processors without a pre-rinse, reduce the spiral tank development times by up to 15%. A pre-rinse is not recommended as it can lead to uneven processing. FIXATION After development, rinse the film in water or ILFORD ILFOSTOP or ILFOSTOP PRO stop bath (1+19) for 10 seconds at 20C/68F, and fix in ILFORD HYPAM or ILFORD RAPID FIXER (1+4) for 25 minutes at 20C/68F. WASHING Where a non-hardening fixer, such as HYPAM or ILFORD RAPID FIXER, has been used, wash the film in running water for 510 minutes at a temperature within 5C/9F of the processing temperature.
10 111/2 1 3
1 8
15 18 17 23 4 5
12 /
T-MAX XTOL
8 8
12 /
7 7
12 /
8 9
12 /
5 6 9
61/2 7
1/2
7 8
12 /
11
3 / 4
19 6
1/2
10 12
11
1 1/2 13 1 1/2 20 1 5